The current Brussels EU Regulation No. 1235/2011, valid from May 30, 2012, has introduced an European Tyre Label with wet grip index G classes from A to G for passenger car tyres C1, light commercial vehicles tyres C2 and heavy truck- and bus tyres C3. Every wet grip class for each vehicle category has a defined band of numerical values for the wet grip index G. The legislated wet grip values G in this EU- Regulation are very low. The measured braking distances and corresponding impact speeds of the test vehicles are showing very critical results. Regulation No. 1235/2011 of the European Parliament and the Council for Type Approval of Vehicles (EU) should be changed in such a way, that for C1-tyres (normal passenger cars tyres) the minimum wet grip index G is 1.25. All C2-tyres (light commercial vehicles tyres) should at least meet a minimum wet grip index of G = 1.1. All C3-tyres (heavy trucks and buses tyres) should at least meet a minimum wet grip index of G = 0.95. Due to the missing lower limits for G in the wet grip class F for C1, C2 and C3 tyres according to Commission Regulation (EU) No. 1235/2011, officially valid from 30 May 2012, a tyre-to-road coefficient of adhesion in the extreme of 0 (zero) is legally permitted. This is an apparent flaw in above cited EU Regulation, which causes a potential danger to the road traffic safety for all motor vehicles in Europe with such tyres. The wet grip class F has to be removed urgently from said EURegulation, since a direct liability of the responsible EU-Commission can not be excluded.
The declining trend since 1991 in the number of killed people was broken in 2011 when overall 4 009 people died in traffic accidents in Germany. The question arises if there is a stagnating trend of fatalities in Germany in future? By breaking down the accidents with casualties towards a monthly view one can see a decreasing trend of fatalities in the warmer months especially since 2009. When comparing against winter months higher deviations are observed. In December 2011 an increase of 191 traffic deaths were registered (181 in 2010 compared to 372 in 2011). Further analyses of different accident influences were evaluated and their possibility of drastic change from one year to the other was determined. As seen weather- and environmental conditions are one of the major contributing factors and are one of the causes for the increased number of fatalities. To support the underlying assumption a model had been created to calculate the number of traffic deaths on a daily basis approach. As an input, road conditions projected through weather parameters and also different driving behaviors on weekdays or holidays were used. As a result, estimates of daily fatality with up to 75% precision can be achieved out of the 2009, 2010 and 2011 data. Further on it shows that weather and street conditions have a high influence on the overall resulting number of traffic accidents with casualties, and especially to the number of fatalities. Hence it is estimated that approximately 3 300 people were killed in traffic accidents in Germany in 2013 which would be again a reduction of another 13% compared to 2012. Therefore an answer to the question will be that the decreasing trend in traffic fatalities in Germany somehow is not broken when environmental conditions are included in national statistics. Their effects will become more visible in future accident statistics and it is estimated variances of 5% to 8% of the annual number of traffic fatalities in Germany will be seen.
Today's volumes of traffic require more and more responsibility from each individual road user in their interactions. Those who drive motor vehicles have the singular obligation to minimise the risk of accidents and hence the severity of injuries, particularly with a view to the most vulnerable road users such as motor bikes, bikes and pedestrians. Since responsible and pro-active driving depends first and foremost on the visual information relayed by our eyes and the visual channel this requires good command of the traffic and all-round visibility from our driver's seat. Granted that human error can never be fully excluded, improving visibility around the car is nevertheless an urgent priority. To do so, we need to rate visibility in the most realistic driving situations. Since the existing visibility metrics and methodology are not applicable to real-life driving situations, this study aimed at developing a new visibility rating methodology based on real-life accident scenarios. On the basis of the cases documented by the accident research project, this study analysed criteria indicative of diminishing visibility on the one hand and revealing some peculiarities in connection with the visibility issue on the other. Based on the above, the project set out to develop a rating methodology allowing to assess all-round visibility in various road situations taking into account both driver and road geometries. In this context, the assessment of visibility while turning a corner, crossing an intersection and joining traffic on a major road (priority through route) is of major importance. The first tests have shown that critical situations can be avoided by adapting the relevant geometries and technical solutions and that significant improvements of road safety can be derived therefrom.
For the estimation of the benefit and effect of innovative Driver Assistance Systems (DAS) on the collision positions and by association on the accident severity, together with the economic benefit, it becomes necessary to simulate and evaluate a variety of virtual accidents with different start values (e.g. initial speed). Taken into account the effort necessary for a manual reconstruction, only an automated crash computation can be considered for this task. This paper explains the development of an automated crash computation based on GIDAS. The focus will be on the design of the virtual vehicle models, the method of the crash computation as well as exemplary applications of the automated crash computation. For the first time an automated crash computation of passenger car accidents has been realized. Using the automated crash computation different tasks within the field of vehicle safety can be elaborated. This includes, for example, the calculation of specific accident parameters (such as EES or delta-V) for various accident constellations and the estimation of the economic benefit of DAS using IRFs (Injury Risk Functions).
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
India is one of the leading countries reporting highest road accidents & related injuries. TMARG (Tata Motors Accident Research Group) has been recording crashes in association with M/s. Lokamanya Medical Foundation since 2011 with M/s, Amandeep Hospitals since Aug 2013. This study has highlighted some accident types not discussed extensively in literature. Trucks to Truck impacts " Cabin interaction with overhanging loadbody structures and Offset underside impacts for passenger vehicles are seen in significant numbers. The paper discusses these in more detail including severity.
Within the COST Action TU1101 the working group WG 1 is dealing with acceptance criteria and problems in helmet use while bicycling concerning conspicuity, thermal stress, ventilation deficits and other potential confounding. To analyze the helmet usage practice of bicyclists in Europe a questionnaire was developed in the scope of working group 1 to collect relevant information by means of a field study. The questionnaire consists of some 66 questions covering the fields of personal data of the cyclist, riding und helmet usage habits, information concerning the helmet model and the sensation of the helmet, as well as information on previous bicycle accidents. A second complementary study is conducted to analyze if the use of a bicycle helmet influences the seating geometry and the posture of cyclists when riding a bicycle and if the if the helmet vertically limits the vision. For this purpose cyclists with and without helmets were photographed in real world situations and relevant geometrical values such as the decline of the torso, the head posture of the upper vertical vision limit due to the helmet were established from the photos. The interim results of the field studies which were conducted in Germany by the Hannover Medical School are presented in this study. Some 227 questionnaires were filled out, of which 67 participants had used a helmet and 42 of the 227 participants have had a bicycle accident before. For the analysis of the riding position and posture of the cyclist over 40 pictures of riders with a helmet and over 240 pictures of riders without a helmet were measured concerning the seating geometry to describe the influence of using a bicycle helmet. Some results in summary: From the riders interviewed with the questionnaire only 11% of the city bike riders and 12% of the mountain bike riders always used the helmet, while 38% of the racing bike riders and 88% of the e-bike-riders always used the helmet. The helmet use seems not to change the sensation of safety of cycling compared to the use of a car. The arguments for not wearing a helmet are mostly stated to be the short distance of a trip, high temperatures or carelessness and waste of time. The reasons for using a helmet are stated to be the feeling of safety and being used to using a helmet. Being a role model for others was also stated to be a reason for helmet use. Concerning the sensation of the helmet 9% of the riders reported problems with the field of vision when using a helmet, 57% saw the problem of sweating too much, and 10% reported headaches or other unpleasant symptoms like pressure on the forehead when using the helmet. The analysis of the seating posture from the pictures taken of cyclists revealed that older cyclists generally have a riding position where the handle bar is higher than the seat (0-° to 10-° incline from seat to handlebar), while younger riders had a higher variance (between -10-° decline and 20-° incline). Further, elderly riders and riders with helmets seem to have a more upright position of the upper body when cycling. The vertical vision limit due to the helmet is determined by the front rim of the helmet (mostly the sun shade). Typical values here range from 0-° (horizontal line from the eye to the sun shade) to 75-° upwards, in which elderly riders tend to have a slightly higher vertical vision limit possibly due to the helmet being worn more towards the face.
Introduction: The method of causation analysis applied under the German accident survey GIDAS, which is based on Accident Causation Analysis System (ACAS) focuses on an on-scene data collection of predominantly directly event-related causation factors which were crucial in the accident emergence as situational resulting events and influences. The paradigm underlying this method refers to the findings of the psychological traffic accident research that most causally relevant features of the system components human, infrastructure and vehicle technology are found directly in the situation shortly before the accident. This justifies the survey method which is conducted directly at the accident (on-scene), shortly after the accident occurrence (in-time) with the detection of human-related causes (in-depth). Human aspects of the situation analysis that interact and influence the risk situations shortly before the collision are reported as errors, lapses, mistakes and failures in ACAS in specific categories and subcategories. Thus methodically ACAS is designed primarily for the collection of accident features on the level of operational action, which certainly leads to valid findings and behavioral causes of accidents. The enhancement by means of Moderating Conditions concerns the pre-crash phase in different levels: strategical, tactical and operational.
While it is important to track trends in the number of road accidents in different countries using national statistics, there is a need for data with more detailed information, so called in-depth accident data. For this reason, several accident data projects emerged worldwide in recent years. However, also different data standards were established and so comparative analysis of international in-depth data has been very hard to conduct, so far. This is why the project iGLAD (Initiative for the Global Harmonization of Accident Data) was established and created the prerequisites for building up a standardized dataset out of the common denominator of different in-depth accident databases from Europe, USA and Asia. In the first phase, the project received funding from ACEA to compile an initial database. To accomplish this, a suitable data scheme has been defined, a pilot study has been conducted as proof of concept and the recoding of the first common data base has been initiated. Also, to prepare the project for its self-supporting continuation in the next years, a business model has been developed. This paper reports the history and status of the project, the current challenges and the creation of a capable consortium to maintain the data. In mid-2014, the initial database containing 1550 cases from 10 different countries will be completed and a first detailed view on this data will be possible.
In 2014 the sixth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Topics of this report are: Road construction (highways, interstate roads, urban by-passes, cycle tracks, construction sites, level crossings removal), traffic management systems, road tunnel equipment, harmonisation of vehicle regulations, accident statistics and accident research, passive vehicle safety, active vehicle safety , automotive environmental protection and rescue systems.
EEVC Status report
(2001)
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
Es wird über einen Kongress zur Gestaltung von Verkehrssicherheitskampagnen berichtet. Ziel dieses Kongresses war es, im europäischen Vergleich Stellenwert und Wirkung verschiedener Stilmittel und insbesondere die Vor- und Nachteile der Konfrontation als Instrument von Kampagnen herauszuarbeiten. Der Kongress bestätigte die verkehrspolitische These, dass es in der Verkehrssicherheitsarbeit keine für alle Staaten richtigen Konzepte für Erziehung und Aufklärung geben kann.
Die Autoren erläutern die Beratungen des 37. Deutschen Verkehrsgerichtstages zum Thema "Arzneimittel und Verkehrssicherheit". Die nur durch Prüfung des Einzelfalls zu belegende arzneimitttelbedingte Fahruntüchtigkeit wird in ihrer Komplexität dargestellt. Die offiziellen Empfehlungen des Verkehrsgerichtstages zu diesem Thema werden vorgestellt.
Es wird über aktuelle Arbeiten zur Unfallprävention bei jungen Fahrern und Fahranfängern berichtet. Hierzu hat im Oktober 2001 die internationale Konferenz "Junge Fahrer und Fahrerinnen" stattgefunden. Außerdem wird auf die Auswertung internationaler Erfahrungen mit neuen Maßnahmenansätzen zur Unfallprävention bei jungen Fahrern und Fahranfängern und die Einrichtung einer Projektgruppe "Begleitetes Fahren" der Bundesanstalt für Straßenwesen hingewiesen.
Das zweite Treffen der Koordinierungsstelle "Vernetzte Verkehrssicherheitsarbeit im Verkehrsverbund Rhein-Sieg" mit den örtlichen Kinderunfallkommissionen fand im September 2006 statt. Über 40 Teilnehmer vertraten die überwiegend aus Nordrhein-Westfalen kommenden Kommissionen. Schwerpunkt der Veranstaltung war das Thema "Schulweg- und Mobilitätspläne - Erfahrungen aus der Praxis". In drei Workshops wurden folgende Themen diskutiert: 1. Der Schulweg- und Mobilitätsplan als gemeinsame Aufgabe von Schule, Polizei, Gemeinde und Eltern; 2. Verkehrssicherheitsprobleme und wie man sie erkennen kann; 3. Gestaltungsmöglichkeiten der Pläne für Grund- und weiterführende Schulen und Überprüfung der Effektivität von Schulweg- und Mobilitätsplänen. In den Workshops berichteten Vertreter verschiedener Kinderunfallkommissionen über ihre Erfahrungen aus der Praxis bei der Erstellung der Pläne. Für die Verkehrssicherheitsanalyse verwiesen die Teilnehmer auf positive Erfahrungen mit der elektronischen Unfalltypensteckkarte. Die Erstellung von Schulweg- und Mobilitätsplänen könnte durch die Bereitstellung von Computerprogrammen sehr vereinfacht werden. Die Pläne selbst sollten in verschiedenen Formen zur Verfügung stehen: als Flyer, im Internet und als Poster. Die Abschlussdiskussion zeigte, dass bei der Erstellung von Schulweg- und Mobilitätsplänen noch viele Fragen zu klären sind. Zudem sollte grundsätzlich geklärt werden, welche Rahmenbedingungen geschaffen werden müssen, um die Arbeit der Kinderkommissionen zu fördern und zu unterstützen.
Das 11. Kolloquium Straßenbetriebsdienst der Forschungsgesellschaft für Straßen- und Verkehrswesen fand nach 10 Veranstaltungen in der Technischen Universität Darmstadt erstmals in der Universität (TH) Karlsruhe statt. Die Veranstaltung hatte erneut über 250 Zuhörer aus dem In- und Ausland nach Karlsruhe geführt. Ihnen wurde ein umfangreiches Vortragsprogramm mit insgesamt 17 Vorträgen angeboten, das alle wesentlichen Aspekte des Straßenbetriebsdienstes umfasste. Sie wurden in den Themenblöcken "Aktuelle Themen im Straßenbetriebsdienst", "Ergebnisse laufender und abgeschlossener Forschungsvorhaben", "Techniken und Strategien im Winterdienst und Umweltaspekte des Straßenbetriebsdienstes" präsentiert. Zum Rahmenprogramm der Veranstaltung gehörten eine Begleitausstellung, eine Werksbesichtigung und praktische Gerätevorführungen.
Vor etwa 70 Teilnehmern aus Straßenbauverwaltungen, Ingenieurbüros und Herstellerfirmen wurde die Problematik des Lärms im Zusammenhang mit Fahrbahnübergängen (FÜ) als Verbindungsglied zur Überbrückung des Spalts zwischen Brücke und anschließender Straße dargestellt und erörtert. Beteiligt waren neben den Experten des Brückenbaus auch die zuständigen Fachleute aus dem Bereich Immissionsschutz und Fahrzeug/Fahrbahn der BASt. Von den Vortragenden wurden die verschiedenen Gesichtspunkte der Lärmentstehung, die bereits angestellten Versuche zur Lärmminderung und die weiteren Möglichkeiten zur Reduzierung des Lärms dargestellt. Das Problem ist noch nicht gelöst. Der Lamellenübergang stellt den heutigen Stand der Technik dar. Man muss in überschaubarer Zeit zu Verbesserungen gelangen.
Es wird über die Fachvorträge des Kolloquiums "Straßenbetriebsdienst" informiert, das zum neunten Mal gemeinsam von der Forschungsgesellschaft für Straßen- und Verkehrswesen und dem Fachgebiet Straßenwesen der Technischen Universität Darmstadt im Oktober 1999 veranstaltet wurde. In kurzen Zusammenfassungen wird über die Vorträge der drei Themenblöcke "Aktuelle Probleme des Straßenbetriebsdienstes", "Umweltaspekte der betrieblichen Straßenunterhaltung" und "Techniken und Strategien für einen wirksamen Straßenwinterdienst" berichtet.
Die Bundesanstalt für Straßenwesen (BASt) führte gemeinsam mit dem Laboratoire Central des Ponts et Chaussées (LCPC) am 7. und 8.12.2000 in Straßburg eine Fachtagung zum Thema "Straßenverkehrslärm" durch. Im Laufe des Workshops wurden Projekte aus nationalen Forschungsprogrammen vorgestellt, Forschungsergebnisse ausgetauscht sowie Möglichkeiten der Kooperation von BASt und LCPC im Bereich Straßenverkehrslärm auf bilateraler und europäischer Ebene erörtert. Der Workshop beinhaltete die beiden Schwerpunktbereiche Lärmemissionen des Straßenverkehrslärms und Schallausbreitung im Straßenverkehr.
Die Arbeitsgruppe Erd- und Grundbau der Forschungsgesellschaft für Straßen- und Verkehrswesen (FGSV) hat am 12. und 13. März 2003 ihre 10. Erd- und Grundbautagung in Stade ausgerichtet. Im Zusammenhang damit wurde eine Exkursion zu den umfangreichen Erdbauarbeiten auf schwierigsten Untergrundverhältnissen im Zuge der Baumaßnahme der BAB A26 zwischen Stade und Horneburg realisiert. Die Tagung wurde von circa 300 Teilnehmern besucht, darunter 13 Fachkollegen aus den europäischen Nachbarländern. In insgesamt vier Blöcken der Vortrags- und Diskussionsveranstaltung wurde über neue Technische Regelwerke, Erfahrungen aus der Baupraxis sowie über aktuelle Forschungsergebnisse berichtet und diskutiert.
Die Arbeitsgruppe Erd- und Grundbau der Forschungsgesellschaft für Straßen- und Verkehrswesen (FGSV) hat am 12. und 13. März 2003 ihre 10. Erd- und Grundbautagung in Stade ausgerichtet. Im Zusammenhang damit wurde eine Exkursion zu den umfangreichen Erdbauarbeiten auf schwierigsten Untergrundverhältnissen im Zuge der Baumaßnahme der BAB A 26 zwischen Stade und Horneburg realisiert. Die Tagung wurde von circa 300 Teilnehmern besucht, darunter 13 Fachkollegen aus den europäischen Nachbarländern. In insgesamt vier Blöcken der Vortrags- und Diskussionsveranstaltung wurde über neue Technische Regelwerke, Erfahrungen aus der Baupraxis sowie über aktuelle Forschungsergebnisse berichtet und diskutiert.
Das 10. Kolloquium "Straßenbetriebsdienst", das in zweijährigem Turnus von der Forschungsgesellschaft für Straßen- und Verkehrswesen in Zusammenarbeit mit dem Fachgebiet Straßenwesen der Technischen Universität Darmstadt veranstaltet wird, fand am 17. und 18. Oktober 2001 in Darmstadt statt. Über 250 Teilnehmer waren wiederum der Einladung gefolgt. Auf vielfachen Wunsch wurde erstmals eine kleine Begleitausstellung organisiert, die Highlights, nicht aber ein umfassendes Lieferprogramm zeigen sollte. Die insgesamt 17 Vorträge der Veranstaltung wurden in drei Themenblöcken präsentiert: Aktuelle Probleme des Straßenbetriebsdienstes, Techniken und Strategien für einen wirksamen Straßenwinterdienst und Umweltaspekte der betrieblichen Straßenunterhaltung. Die Vorträge haben auf breiter Linie erneut unter Beweis gestellt, dass auf allen Ebenen der Verwaltung, der Industrie und der wissenschaftlichen Forschung vielfältige Anstrengungen unternommen werden, das bereits erreichte, auch im internationalen Vergleich hohe Niveau des Straßenunterhaltungs- und Winterdienstes weiter zu verbessern. Die eingeleiteten Maßnahmen bedürfen jedoch der konsequenten Weiterverfolgung. Der abschließende Teil 2 enthält die Übersicht über die Themenblöcke Techniken und Strategien für einen wirksamen Straßenwinterdienst (3.) und Umweltaspekte der betrieblichen Straßenunterhaltung (4.) sowie ein Resümee (5.).
Betonfahrbahndecken werden seit vielen Jahrzehnten mit guten Gebrauchseigenschaften und langer Nutzungsdauer hergestellt. Um den wachsenden Anforderungen hinsichtlich der Verkehrssicherheit, der Umweltverträglichkeit und der Wirtschaftlichkeit gerecht werden zu können, ist eine stetige Weiterentwicklung erforderlich. Im September 2006 fand in Brüssel das 10. Internationale Betonstraßen Symposium statt. Im Rahmen umfangreicher Forschungsarbeiten und Studien auf Erprobungsstrecken wurden auf internationaler Ebene Untersuchungen zur Dauerhaftigkeit von Betonfahrbahnen durchgeführt. Der vorliegende Bericht stellt die Zusammenfassung von insgesamt 12 Fachbeiträgen aus 9 Nationen zum Themenblock "Kosteneffiziente und langlebige Straßen" dar.
Traditionsgemäß berichtet der Arbeitsgruppenleiter anlässlich der Erd- und Grundbautagung über die Tätigkeiten der Arbeitsausschüsse und Arbeitskreise zwischen den Tagungen. Die wesentlichen Aufgaben der Gremien bestehen in der Fortschreibung der Regelwerke auf der Basis der initiierten und betreuten Forschungsprojekte. Diese Aufgaben sind Schwerpunkte des Berichts. Außerdem wird auf die bisherigen Ergebnisse bei der Erprobung der Zusammenarbeit von Eisenbahnbundesamt, Deutsche Bahn AG (DB AG) und Forschungsgesellschaft für Straßen- und Verkehrswesen (FGSV) eingegangen. In einem Überblick wird die seit 1. Januar 2007 gültige Struktur der Arbeitsgruppe "Erd- und Grundbau" mit ihren Arbeitsausschüssen und Arbeitskreisen vorgestellt.
In der Öffentlichkeit wird allgemein angenommen, dass Massenunfälle aufgrund schlechter Straßen- und Sichtverhältnisse passieren, vor allem bei Nebel. Statistisch gesehen ereignet sich das Ineinanderfahren zahlreicher Fahrzeuge aber wesentlich häufiger bei guter Sicht. Was sind die Gründe? Dieser Frage wurde auf einem Presseseminar des Bundesministeriums für Verkehr am 14. und 15. September 1994 in Kassel nachgegangen. Dabei wurde das Phänomen des Massenunfalls aus den verschiedensten Blickwinkeln betrachtet: Was ist ein Massenunfall? Wie arbeitet die Polizei? Welche Probleme haben Rettungsdienste und Notfallmediziner? Was geht im Kopf der beteiligten Autofahrer vor sich? Gibt es technische Hilfen und wirksame Lernsysteme?
T. DÜNCHHEIM erörtert in seinem Einführungsvortrag zu "Die Stellung der Gemeinden im Straßenrecht" die kommunalen Gestaltungsspielräume hinsichtlich ihres Satzungsrechts, das sich auf -§ 19 StrWG NRW stützen lässt. Er schildert die Auswirkungen dieser Gestaltung auf das Straßen- und Straßenverkehrsrecht, die letztlich Ausfluss der gemeindlichen Selbstverwaltungsgarantie sind. Dabei problematisiert er die Abgrenzung zwischen straßenrechtlichem Gemeingebrauch und Sondernutzung sowie die Bedeutung der rechtlichen Ausgestaltung des Straßen- und Straßenverkehrsrechts. Hierbei wird die Anwendung des -§ 45 StVO durch die Gemeinden einer kritischen Analyse unterzogen. A. NETTER schildert in seinem Beitrag "Aktuelle Rechtsfragen der Ortsdurchfahrten" die Gremienstruktur im Straßenwesen und den Einfluss des Europarechts, des Bundes- und Landesstraßenrechts sowie den Ortsdurchfahrtenrichtlinien auf das Straßenwesen. Er stellt dabei die Folgen der Aufhebung der Radwegbenutzungspflicht sowie die aus der Straßenbaulast folgende Entwässerungsverpflichtung der Straßenbaulastträger und ihre Umsetzung in den Gemeinden dar. U. WEGNER berichtet in ihrem Beitrag "Aktuelle Entwicklungen des Verbandsklagerechts" über die Auswirkungen europäischer Richtlinien auf das Umweltrecht. In diesem Zusammenhang wird eine wegweisende Entscheidung des BVerwG erörtert, welche die direkte Anwendung des Art. 9 Abs. 3 AK zum Gegenstand hat. Trotz der Einführung einer bundesrechtlichen Verbandsklage in -§ 64 BNatSchG sei das Problem der Wahrung von Allgemeininteressen nicht gelöst, da diese Norm die Interessen des Umweltschutzes nicht hinreichend zu schützen vermöge. Der Beitrag "Inanspruchnahme öffentlicher Wege durch TK-Unternehmen" von U. STELKENS, stellt eine differenzierte Auseinandersetzung mit dem TKG-Wegerecht dar. Er konstatiert, dass die Bestimmungen des TKG im Wesentlichen auf den Normen des Telegraphenwegegesetz (TWG) basieren. Daher bestehen Spannungsverhältnisse und Reibungsflächen zwischen den verschiedenen Abschnitten des TKG, da das TKG und das TWG unterschiedliche Ziele verfolgen. Beispielsweise seien die -§ 77a bis -§ 77e TKG nicht auf die -§ 68 bis -§ 77 TKG abgestimmt worden. Der abschließende Beitrag "Fachplanerische Auswirkungen des Umweltschadensgesetzes" von M. PETERSEN widmet sich der Frage, ob und welche Auswirkungen das Umweltschadensgesetz auf das Fachplanungsrecht hat. Zunächst wird allgemein herausgearbeitet, dass das Umweltschadensgesetz nicht Schadensersatz- oder Ausgleichsleistungen eines geschädigten Dritten bezweckt; vielmehr sollen Umweltschäden vermieden und die Wiederherstellung geschädigter Umweltgüter erreicht werden. Die Frage, ob und inwieweit das Umweltschadensgesetz Auswirkungen auf das Fachplanungsrecht hat, hängt davon ab, ob die Haftungstatbestände des -§ 3 Abs. 1 USchadG einschlägig sind.
The frontal crash is still an important contributor to deaths and serious injured resulting from road accidents in Europe. As the Hybrid-III dummy used in crash tests is over two decades old, the European Enhanced Vehicle-safety Committee is studying the potential for a new test device. Key is the availability of a well-defined set of requirements that identifies the minimum level of biofidelity required for an advanced frontal dummy. In this paper, a complete set of frontal impact biofidelity requirements, consisting of references , description of test conditions and corridors, is presented.
The Swedish National Road Administration (SNRA), the Japanese Automobile Research Institute (JARI) and the Federal Highway Research Institute (BASt) are co-operating in the International Harmonized Research Activities on Intelligent Transportation Systems (IHRA-ITS). Under this umbrella a joint study was conducted. The overall objective of this study was to contribute to the definition and validation of a "battery of tools" which enables a prediction and an assessment of changes in driver workload due to the use of in-vehicle information systems (IVIS) while driving. In this sense \"validation\" means to produce empirical evidence from which it can be concluded that these methods reliably discriminate between IVIS which differ in terms of relevant features of the HMI-design. Additionally these methods should also be sensitive to the task demands imposed on the driver by the traffic situation and their interactions with HMI-design. To achieve these goals experimental validation studies (on-road and in the simulator) were performed in Sweden, Germany and Japan. As a common element these studies focused on the secondary task methodology as an approach to the study of driver workload. In a joint German-Swedish on-road study the Peripheral Detection Task (PDT) was assessed with respect to its sensitivity to the complexity of traffic situations and effects of different types of navigation systems. Results show that the PDT performance of both the German and the Swedish subjects reflects the task demands of the traffic situations better than those of the IVIS. However, alternative explanations are possible which will be examined by further analyses. Results of this study are supplemented by the Japanese study where informational demands induced by various traffic situations were analysed by using a simple arithmetic task as a secondary task. Results of this study show that relatively large task demands can be expected even from simple traffic situations.
The objective was to develop and validate a crash trolley (reference vehicle) equipped with a compartment and a full restraint system for driver and front seat passenger which can be used in full scale crash testing. Furthermore, the crash trolley should have a suspension to show rotation and nick effects similar to real vehicles. Within the development phase the reference vehicle was build based on a European family car. Special attention was needed to provide appropriate strength to the trolley and its suspension. The reference vehicle is equipped with a restraint system consisting of airbags, pedals, seats, dashboard, and windscreen. On the front of the vehicle different crash barriers can be installed to provide miscellaneous deceleration pulses. For the validation phase a series of low and high speed crash tests with HIII dummies were conducted and compared with full scale tests. For the comparison deceleration pulse, dummy numbers and vehicle movement were analyzed. Validation tests with velocities up to 60 km/h showed promising results. The compartment and the suspension systems stayed stable. Rotation effects were comparable with full scale car crash tests. The airbags and seat belt system worked reasonable. The acceleration pulse compared to an Euro NCAP test had a similar characteristic but was in general slightly lower. After the successful validation the reference vehicle is already in use in different studies in the field of vehicle safety research at BASt.
Topics of the status report are: Road accidents in Germany " Socio-economic costs due to road traffic accidents in Germany " Vehicle population and road performance " Electromobility " Alternative power train technologies: market penetration and consequences. The following research subjects are presented: Safety of electric vehicles " Driving dynamics of electric propelled vehicles " New requirements for the periodic technical inspection of electric and hybrid vehicles " Forward looking safety systems " Periodic roadworthiness tests " Cooperative systems: integration of existing systems " Safety related traffic information " Urban space: User oriented assistance systems and network management " Automated driving " Study on camera-monitor-systems " Freight transport " BioRID TEG, dummy harmonization " Frontal impact and compatibility " Child safety " FlexPLI " GIDAS: a blueprint for worldwide in-depth road accident investigations " Druid: Driving under the influence of drugs, alcohol and medicines " Smoke and toxicity in bus fires.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Topics of this report are: Road accidents in Germany - Socio-economic costs due to road traffic accidents - Vehicle population and road performance " Automotive IT " Electromobility. The following research subjects are presented: Safety of electric vehicles - Forward looking safety systems - Cooperative systems - Safety related traffic information - Freight transport: Action plan freight transport and trial with longer trucks - Lane departure warning systems and Advanced emergency braking systems (AEBS) for heavy duty vehicles - Dummy harmonization " Compatibility - Child safety - Virtual testing - Driving under the influence of drugs, alcohol and medicines - Fire safety of buses - Milled shoulder rumble strips - Conspicuity of powered-two-wheelers - Automatically dipped high beam and rear view mirrors.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Technical progress in automotive engineering focuses at the moment on two competing branches: improving safety and reducing energy consumption. Recent consideration has been given to a third factor, cost to the consumer. Challenges are presented by demographic changes, especially with increasing participation of elderly people in road traffic. The report considers the recent history of road accidents in Germany and statistics relating to vehicle population and road performance. There is a general trend towards decreasing numbers of accidents and their severity. Transport is responsible for roughly 20% of CO2 emissions and approximately 70% of total petroleum consumption. The Federal Government has responded to these challenges by publishing the Freight Transport and Logistics Masterplan in the summer of 2008. It describes the strategic transport policy direction and the key elements of the future course of action which are to be used to ensure the provision of efficient infrastructure and, at the same time, to reduce the amount of energy consumed by vehicles and make transport more efficient, cleaner and quieter. This document contains a number of concrete measures subsumed under the following six objectives: Making optimum use of transport infrastructure - shaping transport to make it more efficient; Reducing the number of journeys - ensuring mobility; Transferring more traffic to the railways and inland waterways; Upgrading more transport arteries and hubs; Environmentally friendly, climate friendly, quiet and safe transport, and Good working conditions and good training in the freight transport industry. Progress in research is outlined in the following areas: Daytime Running Lights for Motorcycles; Safety of hydrogen vehicles - addressing safety and environmental issues by development of a Global Technical Regulation for hydrogen vehicles; Elements of active vehicle safety for elderly drivers; Periodical Technical Inspection of electronically controlled systems in road vehicles - Electronic Stability Control; Pedestrian protection; Crash Compatibility - role of collision partner in passive safety tests; Child safety; Euro NCAP - Child Restraint Systems, and German Field Operational Test on Car-to-Car and Car-to-Infrastructure Systems (SIM-TD). The research project AKTIV - "Adaptive and Cooperative Technologies for Intelligent Traffic" encompasses the design, development, and evaluation of novel driver assistance systems, knowledge and information technologies and is set up to find solutions for efficient traffic management and Car-to-Car and Car-to-Infrastructure communication for future cooperative vehicle applications. The European Statement of Principles on the Human Machine Interface (HMI), presented at the eSafety Conference, which was held in Berlin on 5/6 June 2007, addresses issues such as Real Time Traffic Information (RTTI), Legal issues of Advanced Driver Assistance Systems (ADAS) and e-security.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
There is a need to continue to set the right vehicle safety policy priorities in the future. Research has to point out the most cost efficient and safety relevant measures to further reduce the number of road traffic casualties. The overall development shows that the constant and rapid decrease in the number of road casualties slows down. New innovations need to enter the vehicle market soon, in order to continue the success achieved in the last decade. Priorities for vehicle safety are driven by safety and mobility demands. It is necessary to keep a strong lid on all aspects of elderly and vulnerable road users. The fraction of powered-two-wheelers (PTW) is a priority group. PTWs have a risk of being involved in an accident, 14times higher than that of a passenger car. However, the figures do also show that every second fatality is a car occupant. Therefore passenger car safety remains to be top priority. Heavy goods vehicles are overly represented in fatal accidents, addressing the need to make these vehicles more compatible with other road users. These facts highlight the necessity not only to increase vehicles" self protection, but also to make cars - and trucks - more compatible and safe. Cycling is a strongly increasing mode of transport. This is a further reason to demand better protection for cyclists and pedestrians from car design and car active and integrated safety systems. Another priority for future vehicle safety is related to demographics. It is less known that the purely demographic effect will be superimposed by an increasing wish of elderly people to be mobile. However, elderly people show deficits concerning their biomechanics. This emphasizes the need for better and more adaptive restraint systems, but also further technological challenges and demands for active safety systems. However, in order to progress, current technological limitations have to be overcome. Cost benefit considerations, but also consumer acceptance and desires, will drive this process.
Accident research 2.0: New methods for representative evaluation of integral safety in traffic
(2013)
BMW has developed a procedure for rating Advanced Driver Assistance Systems (ADAS) benefits that integrates two distinct tools. The tool "S.A.F.E.R." is designed to analyze the pre-crash phase. The aim of S.A.F.E.R. is to simulate all relevant processes in sufficient detail to obtain reproducible estimates of key indicators (effectiveness, false positives, etc.). The relevant processes include not only traffic and vehicle dynamics, but also environmental and most importantly human factors. Representative distributions of factors and parameters are obtained by taking the stochastic variation of all relevant parameters into account in the simulations. The second tool, known as "ICOS", has been designed to provide a high-resolution, high-fidelity description of crash phase dynamics. If one converts the outputs of stochastic simulation into inputs for crash dynamics, the result is a comprehensive description of exactly how a safety system can reduce injuries. Applications currently focus on high-fidelity simulation of individual crashes in order to enhance our understanding and optimization of connected safety systems. An integrated simulation process thus allows an exact prediction of the effectiveness in individual cases in terms of injury severity. The development and rating of integral safety need to reflect the true efficiency in the field. The integrated approach described here could provide a valid and reproducible basis for rating connected systems of active and passive safety. In particular, "virtual experiments" using a traffic-based approach and incorporating models of all relevant processes constitute an essential element of the approach.
The presentation deals with the simulation tool rateEFFECT which intends to answer the following questions: Which active safety systems should be developed to maximize safety benefit in real traffic accidents? What is the effectiveness of a specific active safety system in the real world? How many casualties could be avoided by such a system? It is shown that a lot of information is required to simulate existing accidents in order to estimate ADAS effects. This particularly includes numerical values for the pre-crash and in-crash phase. The database GIDAS provides a required minimum number of these parameters for a statistically significant sample.
This paper will outline ETSC's contribution to the European Union's road safety policy 2011-2020. It will present some of the main recommendations from ETSC's Blueprint for the 4th Road Safety Action Programme and will introduce the response to the European Commission's Road Safety Policy Orientations 2011-2020 (published July 2010). The second framework document presented is the Transport White Paper (published March 2011). The paper will focus on new targets and the new vision set for Europe's Road Safety policy picking out some issues in particular such as traffic law enforcement and the protection of vulnerable road users. It will argue that by reinforcing the current Road Safety Policy Orientations, the EU will be better placed to reach its new ambitious goal of halving road deaths by 2020 and the longer term zero casualty vision.
Analysis of the accident scenario of powered two-wheelers on the basis of real-world accidents
(2013)
For the first time since 20 years the German national statistics of traffic accidents revealed an increasing number of fatalities and seriously injured persons in 2011. This negative development was especially caused by increasing numbers in all groups of vulnerable road users (VRU). Furthermore, the comparison of fatality reduction rates between several categories of road users shows that persons on motorcycles show the worst performance over years. Although every second fatality in German traffic accidents is still a car occupant, users of PTW make up more than 20% in the meantime. Assuming further improvements in the field of occupant protection this trend will continue. For that reason, a study on the basis of real-world accidents was conducted to describe the accident scenario involving motorcycles and to identify the reasons of the above-described fact. Approximately 1.800 motorcycle accidents out of GIDAS database were used for the analyses. The first part of the study deals with the question how representative the GIDAS database is for the German motorcycle accident scenario. Afterwards, detailed descriptive statistics on motorcycle accidents were presented considering numerous parameters about the accident scene, environmental influences, vehicle information, individual characteristics, interview data, injury severity and injury causation. One important point is the identification of the most frequent critical situations that are typical for motorcycle accidents. Furthermore, a special focus was on accident causation. Finally, conspicuous facts out of the analysis are emphasized. All in all, the study gives a comprehensive overview about the German motorcycle accident scenario. One the one hand, the use of weighted GIDAS data allows representative and robust statements on the basis of large case numbers; on the other hand highly detailed conclusions can be drawn. The results of the study help to understand the particularities of motorcycle accidents and provide approaches for further improvements in the field of PTW safety.
It is very important for Automotive OEMs to get feedback on their product performance on real roads for continuous improvement. Every OEM has a way of collecting this feedback for various performance parameters. Systematic accident research is a way to generate the information related to safety performance of the vehicle. In India, while there is a large amount of data related to the accidents, it is found this data is aimed at understanding the gross statistics and not directly useful for technology development. This paper explains learnings from a pilot study carried out in collaboration with an Emergency Medical Services provider on one of the expressways (motorways). This pilot study has resulted in development of working model that could now be scaled up at for wider application. The paper also presents some of the important observations based on the data collected.
Police records about traffic accidents like used by IRTAD (International Road Traffic and Accident Database) and CARE (Community Road Accident Database) do not represent all road injuries. For instance, road accidents of bicyclists without a counterpart are usually not reported. Furthermore, IRTAD-like data contains hardly any information on injury outcome and accident circumstances. This information gap leads to an under-representation of the safety concerns of the most vulnerable road users like children and the elderly both in accident research and safety promotion. Injury registration for the European Injury Database (IDB), in turn, combines details of accident causation with diagnostic information that can be used to assess injury severity and long term consequences. The IDB is collecting data from hospital emergency department patients and is being implemented in a growing number of countries. In this article IDB results on mode of transport and injury outcome are presented from a sample of nine EU member states.
While accident statistics on a national level are provided by many countries, there is a need for international data that includes more detailed information about the accident, so called in-depth data. As a consequence, accident data projects have been emerging in different regions of the world. This creates a need for comparable and mergeable data from different countries, enabling the use of already existing accident data resources and helping to expedite the improvement of global road safety. While existing approaches focus that mostly on building a comprehensive accident database from scratch, the iGLAD project (Initiative for the Global Harmonization of Accident Data) attempts a more pragmatic approach by building on top of the work already accomplished in this area and complementing it. The target of iGLAD is to help setting up an additional dataset as a compatibility layer between already existing world wide data sets and integrating the structure of these by defining a common data scheme. This dataset is limited to the common denominator between the existing data sets and is inherently rather small and simple. Eventually, an individual converter for each participating accident investigation group will be built that enables pooling all data sets in a common repository. This not only saves costs and time, and hence makes such a target more feasible, but also creates data that is usable right from the start. This paper gives an overview of the current status of iGLAD and first steps taken. Additionally, some methodological aspects are discussed, next to a glance at other projects working currently on related issues, providing additional input for iGLAD. Finally, an overview of next steps and intended future work is given.
The increasing economics in India has an enormous growth of its road traffic. As observed from official Indian accident statistics the number of road fatalities are one of the highest worldwide. In contrast to most industrialized nations they have an rapidly increasing trend. To come along with this trend it becomes more than essential to understand the traffic accident situation. The official Indian accident statistics gives a glimpse of only basic information. Therefore more detailed data is needed. By using In-depth accident data and officially representative statistics the current accident situation can be evaluated in India, if a suitable weighting methodology is considered. Hence in 2009/2010 a pilot study with the collaboration partner JP-Research India pvt. Ldt. was gathered in Tamil Nadu in south of India. In-depth accident investigations were done around the Coimbatore area on four highways. At first, the collected data is evaluated. Due to consequent and continuous further development based on the first approach a methodology similar to NASS/CDS/GES in the US and GIDAS in Germany was developed. Of course all relevant accident related parameters including pictures and severity information were collected. As a matter of fact based on scaled sketches and reconstruction benefit analyses can be done in order to analyze the accident scenery in India. As a first outcome influence from infrastructure, missing education and vehicle safety were identified as key parameters in order to reduce the number of accidents and casualties. To compare the accident situation against international standards an accident classification for left hand traffic was developed based on the German Insurance classification system. Looking into detail additional accident types were identified and added to create an Indian accident type catalogue. The positive results encouraged several OEMs to participate in this investigation and together with BOSCH a consortium was established in 2010/11. Within one year from beginning in May 2011 about 200 highway accidents were collected, reported and reconstructed using the new standard. Hence a first good overview of the accident situation is available for the Coimbatore Tamil Nadu area. The major target for establishing accident investigations is the extension towards other states of India and urban areas to achieve a better overview of the accident scenery. Therefore local and national authorities have to be embedded in order to strengthen the awareness against traffic safety.
Do learner gain sufficient braking capabilities at the end of education for collision avoidance?
(2013)
The paper describes a test design to evaluate the braking behaviour in the course of the driver education. The results show that the braking capabilities increased during the driver education and the learning effects are the same for males and females. The evaluation limit is set to 6 m/s-². At the beginning of education, 50% of the drivers do not reach this limit, although the driver education car is equipped with an emergency brake assist, which is regularly installed in all vehicles since 2009. After the education, 100% of the drivers can reach the limit. The results are mapped to a collision avoidance scenario.
Since 2008, the authors inspected fatal traffic accidents on the spot every year, with the cooperation of Toyota police station in Aichi pref. In the jurisdiction, numbers of fatal accidents were 18 in 2008, 12 in 2009, 14 accidents in 2010, and 16 in 2011. We here report the results of our analysis of information obtained by detailed inspection for those that occurred from 2008 to 2010. We focused on vehicle-to-pedestrian accidents, which accounted for about 45% of all accidents in 2008. Because many accidents occurred on residential roads not far from pedestrians" homes, it was revealed that the decrease of the collision speed by traffic calming such as humps and zone speed management, was highly effective. On the other hand, pedestrian detection technologies seemed to be also effective as a countermeasure on vehicle side. Every pedestrian position against a vehicle was clarified and TTC (Time to Collision) was calculated provisionally. Pedestrian accidents in intersections were also examined. Among the intersection pedestrian accidents within the jurisdiction, compared with the national average in Japan, the ratio of intersections without a signal and the ratio without a pedestrian crossing were high. According to the comparison of the Japanese traffic accident patterns between 2001 and 2008, pedestrian accidents during turning right and turning left did not decrease much. For elderly drivers, these accidents occurred very often. Finally, single vehicle accidents were analysed with the accident pattern analysis methods used above. There were high numbers of single vehicle accidents against object on single roads. Although fatal accidents against guardrails decreased, the numbers of fatal accidents against a utility pole and a sign pole were nearly constant. As for the impact with narrow width objects such as utility poles, the fatality rate was very high, and countermeasures of both road infrastructure and vehicles seem to be effective.
A concept for Safe-Driving-Trainings with a focus on risky behavior and safety related attitudes has been evaluated. 519 participants have been tested before and after the training by means of a questionnaire with the topics: technical driving competence, awareness of risks, and propensity for anticipation. A control group (131 subjects) was used to check for the possibility of response artifacts. Three months later, 92 members of the treatment group and 25 members of the control group have been tested again. The results show significant positive changes in driving competence, risk awareness, and safety related attitudes, especially anticipation, due to the training. Compared to the control group the participants have become more risk aware and they regard of risk avoiding behavior as more important. The results show that this concept for Safe-Driving-Trainings has not only short-term but, more importantly, long-term positive effects on the safety-relevant attitudes and cognitions of young drivers.
The paper aims to study the injury risk and kinematics of pedestrians involved in different passenger vehicle collisions. Furthermore, the difference of pedestrian kinematics in the accidents involved minivan and sedan was analyzed. The 18 sample cases of passenger car to pedestrian collisions were selected from the database of In-depth Investigation of Vehicle Accident in Changsha of China (IVAC),of which the 12 pedestrian accidents involved in a minivan impact for each case, and the 6 accidents in a sedan impact for each. The selected cases were reconstructed by using mathematical models of pedestrians and accident vehicles in a multi-body dynamic code MADYMO environment. The logistic regression models of the risks for pedestrian AIS 3+ injuries and fatalities were developed in terms of vehicle impact speed by analyzing the minivan-pedestrian and sedan-pedestrian accidents. The difference of pedestrian kinematics was identified by comparing the results from reconstructed pedestrian accidents between the minivans and sedans collisions. The result shows that there is a significant correlation among the impact speed and the severity of pedestrian injuries. The minivan poses greater risk to pedestrian than sedan at the same impact speed. The kinematics of pedestrian was greatly influenced by vehicle front shape.
This study analyses no.39 cases in which n.41 motorcyclists were fatally injured, or 36% of total motorcycle fatalities in Northern Ireland between 2004 and 2010 (n.114). There were n.17 cases (43.6%) where the actions of another vehicle driver caused the collision, in thirteen of these cases the motorcycles had their lights switched on. The remaining n.22 collisions (56.4%) were due to the actions of the motorcyclist. In the approach to the collision scene, there were n.13 cases (31.7%) in which the approach was a right hand bend and in n.8 (19.5%) cases, the approach was a left hand bend. In the remaining n.18 (43.9%) cases, the approach was a straight road. Of the n.17 (41.4%) motorcycles that slid after falling, n.10 (24.4%) fell onto their right side and the remaining n.7 (17.1%) fell onto their left side. The information from this study identifies primary and contributory causes of motorcycle collisions.
The misuse of CRS (child restraint system) is one of the most urgent problems in connection of child safety in cars. Numerous field studies show that more than two thirds of all CRS are used in a wrong way. This misuse could lead to serious injuries for the children. Surprisingly the quality of CRS use is coded much better in accident data (e.g. GIDAS) than the results of observatory field studies show. It is expected that misuse of CRS was not detected by the accident teams in a large number of the cases. An essential part in improving child seats and their usability is the knowledge of the relation between misuse and resulting injuries. For that the analysis and experimental reconstruction of accidents is an important part. For allowing an exact experimental accident reconstruction, it is necessary to have detailed information about the securing situation of the child and about the installation of the CRS in the car.
Automotive interiors have long been a potentially injurious impact area to occupants during accidents, especially in the absence of adequate padding. The U.S. Federal Motor Vehicle Safety Standard (FMVSS) 201, Occupant Protection in Interior Impact, outlines test procedures and performance criteria in order to mitigate potentially injurious head impacts to interior surfaces. FMVSS 201 specifies a finite set of impact locations and applies to passenger vehicles of a specified year range and with a gross vehicle weight rating less than 10,000 lb. In this paper, two head impact test methodologies are presented, a pendulum-test device and a Free Motion Headform (FMH) launching device, which allows for dynamic, repeatable impact evaluation of various vehicle interior surfaces and their impact attenuation abilities. The presented testing includes multiple series that evaluate the effect of differing vehicle upper interior padding on occupant head injury. One study in particular, analyzes a head impact to the side header of a heavy truck (not included in FMVSS 201) during a 90 degree rollover. Additionally, two other series of tests are presented which assess the injury reduction effect of side airbags to near side as well as far side occupants in a side impact scenario. Lastly, a forensic analysis is presented which evaluates two possible head impact locations experienced in a real world accident by analysis of the resulting interior compartment damage utilizing the FMH launching device test method. The data collected and presented includes accelerometer instrumentation and high speed video analysis. These studies demonstrate that adequate padding and airbags are very effective at mitigating head injury potential at impact speeds of 12-25 mph (19-40 kph).
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
Supervision of the safety performance in public transport is one of the main tasks of the Federal Office of Transport (FOT) in Switzerland. Recently a three level system of safety indicators has been defined to cover all means of Swiss public transport. The safety indicators are fed by the FOT incident database since the year 2000. In cooperation with the Institute for Traffic Safety and Automation Engineering (iVA) at TU Braunschweig, Germany, FOT is developing a suitable methodology for the definition and evaluation of the safety targets in Swiss public transport. The methodology is applied for evaluation of safety indicators on a country level and for single transport companies. In a new approach the abovementioned methodology is applied to car incident data to develop an indicator based cross-modal safety measure.
The effect of fatigue on driving has been compared to the effect of alcohol impairment in both driver performance and crash studies. However are crash characteristics and causation mechanisms similar in crashes involving fatigue to those involving alcohol when studied in the real world? This has been explored by examining data held in the EC project SafetyNet Accident Causation Database. Causation data was recorded using the SafetyNet Accident Causation System (SNACS). The focus was on Cars/MPV crashes and drivers assigned the SNACS code Alcohol or Fatigue. The Alcohol group included 44 drivers and the Fatigue group included 47. "Incorrect direction" was a frequently occurring critical event in both the Alcohol and Fatigue groups. The Alcohol group had more contributory factors related to decision making and the Fatigue group had more contributory factors relating to incorrect observations. This analysis does not allow for generalised statements about the significance of the similarities and differences between crashes involving alcohol and fatigue, however the observed differences do suggest that attempts to quantify the effect of fatigue by using levels of alcohol impairment as a benchmark should be done with care.
Real world accident reconstruction with the Total Human Model for Safety (THUMS) in Pam-Crash
(2013)
Further improvement of vehicle safety needs detailed analysis of real world accidents. According to GIDAS (German In-Depth Accident Study) most car to car front accidents occur at mid-crash severity. In this range thoracic injuries already occur. In this study a real world frontal crash with mid-crash severity out of the AARU database was reconstructed. The selected car to car accident was reconstructed by AARU by means of pc-crash software in order to get the initial dynamic accident conditions. These initial conditions were used to reconstruct the complete accident in more detail using FE models for the car structure and the occupants. Occupant simulations were performed with FE HIII-dummy models and the THUMS using Pam-Crash code. An initial THUMS validation was performed in order to verify the model-´s biofidelity by means of table-top test simulations. THUMS bone stiffness values were modified to match the real word occupant age. A comparison between driver and passenger restraint system loading was done, as well as an injury prediction comparison between the HIII-dummy model and THUMS response for both cases. Detailed comparison between the HIII-dummy models and THUMS regarding thoracic loading are discussed.
With an ever rising human life expectancy the share of elderly people in society is constantly rising. This leads to the fact that at the same rate the share of people with age related diseases such as dementia and poor eyesight taking part in traffic will rise and therefore traffic accidents caused by this group of people due to the disease will play an ever greater role. This Situation will be among the future challenges of road safety work. At present this study displays specific characteristics of accidents caused by elderly car drivers (aged 65 or higher) based on the analysis of the German In-Depth Accident Study GIDAS. Herein almost 1000 elderly car drivers were identified as accident participants in the years 2008 to 2011. The focus of this study lies on identifying special types of accidents which are caused by elderly drivers and on characterizing these types with the information gathered on scene and by interviewing the participants. The main evidence analyzed is the knowledge about the accident locality, the trajectories of the participants as well as the reasons for the occurrence of the accidents. Furthermore personal information such as the personal condition before the accident and driving purposes is used to identify patterns of contributing circumstances for accidents caused by elderly traffic participants.
Beside numerous information about vehicles injuries and environmental data the GIDAS database contains detailed reconstruction data. This data is calculated by a reconstruction engineer who handles about 1000 accidents per year. The spectrum of one reconstruction ranges from simple crossing accidents to complex run-off accidents with rollover events. Especially for complex accident scenarios there is a large effort to design the environment of the accident scene within PC-Crash ®. To reduce the reconstruction time by maintaining the high quality of reconstruction 3D-geodata can be useful. Geodata is available for nearly every area in Germany and can be used for a fast and detailed creation of complex accident environments. In combination with the accident sketch areal images of the accident scene can be created and the participants are implemented in the new-built 3D-reconstruction environment. As a consequence, the characteristics of the terrain can be considered within the reconstruction which is especially important for run-off accidents.
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
The GIDAS-investigation team of Dresden (VUFO) has documented more than 11.500 accidents since 1999. The documentation of the accident includes beside vehicle-, injury- and environmental-data very detailed reconstruction data. Within this accident investigation the VUFO began to record the skid resistance of the accident site in 2009. The measurements are divided in macro- and microroughness (Sand depth method and Portable Skid Resistance Tester-SRT-by Munro-Stanley London-©). Both methods are used to determine the skid resistance for more than 1000 passenger cars. The aim of the present study is to find out a relationship between the measured skid resistance, the road conditions and the friction coefficient, which is used to calculate the maximum accelerations and decelerations during a reconstruction of an accident. Basic approach to convert the SRT-value into the friction coefficient is the calculation of the theoretical absorbed energy of the spring rubber system of the swinging arm of lever. This absorbed energy is used to get the friction coefficient by using the equations for the work of friction. To consider the road-behavior, in correlation to the friction coefficient, the results will be merged with existing literature. Last step for this study will be a comparison between actual used friction coefficients all over the GIDAS-database and the theoretical results. The study shows, if it is possible to use the SRT-Measurement for the estimation of a friction coefficient for the reconstruction of a traffic accident. As expected, the GIDAS-Database and the additional measurement of the roughness of the road directly on the spot are an enormous useful dataset.
The grip between the road surface and vehicle tires is the physical basis for the moving of all vehicles in road traffic. In case of an accident the available grip level is one of the most relevant influence factors, influencing the causation and the procedure of the accident. However, the estimation of the grip level is not easy and therefore, is commonly not done on the accident scene. This is especially true for the measurement of the water depth. Until now, real accident databases provide no measurement data about the grip level and the water film depth and thus, the estimation of its influence is not possible yet. From the tyre manufacturers point of view, it is important to know about the road conditions (namely grip level, macro-texture, water depth, temperature) at the accident scene, as well as the operating conditions of the vehicles (braking, loss of control, speed, etc). These data is necessary to define relevant tyre traction tests for the end-user and for regulations. For this reason VUFO and Michelin developed a consistent method for the measurements of grip level and water depth for the accidents of the GIDAS database. The accident research team of Dresden, which documents about 1000 accidents with at least one injured person every year, is measuring the micro-roughness and the macro-roughness directly on the spot. For the measurement of the micro-roughness a Skid Resistance Tester (British Pendulum) is used. The Mean Texture Depth (describing the macro-roughness) is measured by the Sand Depth Method. Since June 2009, measurements for more than 700 accidents including 1200 participants have been carried out. In case of wet or damp road conditions during the accident, the water depth is measured additionally. Therefore VUFO and Michelin developed a special measurement device, which allows measurements with an accuracy of 1/10 millimetre. The measurement point at the accident scene is clearly defined and thus, the results are comparable for all different accidents and participants. The use of the GIDAS database and the accident sampling plan allows representative statements for the German accident scenario. With this data it is possible for the first time to have an accurate view of the road conditions at the accident scene. One possibility is a more detailed estimation of hydroplaning accidents using the actually measured water depths. The development of new testing methods and new tires can be based on the real situation of the road infrastructure. Furthermore, the combination of the technical GIDAS data and the measured road surface properties can also be used for the estimation of effectiveness of several safety systems like the brake assist and/or emergency braking systems. The calculation of a reduced collision speed due to the use of a brake assist is only one example for the application of real measured grip level data.
Having a look at safety to traffic and the prevention of accidents it can be observed that technical improvements in active safety of vehicles have let to various positive effects in this area. Among other components the tyre-road-contact takes a key role in the development of active safety technologies. All forces in accelerating, breaking and vehicle guidance have to be transmitted through the tyre-road contact area by friction forces. A common way to characterize a friction process is to identify the coefficient of friction μ between two touching materials. Even though there are several approaches to experimentially characterise road surfaces, no standard method exists. In this paper an overview of existing test methods is given. Furthermore the preliminary design of a newly developed portable test device with its possibility to investigate the tyre-road-friction of arbitrary roads or even places of accidents is shown.
The European CASPER (Child Advanced Safety Project for European Roads) project studying car child safety includes a sociological approach in order to have a better understanding of the behaviour of parents driving children under 12 years old. A questionnaire was distributed via the internet in Europe with 998 parents (representing 1638 children) from 22 European countries responding. The results inform on the way parents secure their children during a car trip. Many parents did not control how their children were installed in the child restraint system (CRS). A toddler was more likely to travel into a child seat than an older child was. Regarding misuse situations, an important part of the participants did not think that they could make mistakes when fixing the child seat to the car (26%) or when placing the child into the seat (39%). This leaves an important field of action especially by communication via different media and in the CRS sale outlets.
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
Nowadays human-created systems are increasing in complexity due to the interaction of humans and technology. Especially road traffic systems are composed of multitudinous resources (e.g. personnel, vehicles, organizations, etc.), which make it even harder to anticipate the positive and negative effects on safety. One key in achieving a significant reduction of fatalities is seen in driver assistant systems counterbalancing the lack of drivers' capabilities. But the actual outcome of implementing these sophisticated technologies especially on influencing driver's capabilities are yet unknown. Latest research exemplifies an increase of reaction times of drivers in case of dysfunctional driver assistant systems. This research paper applies STAMP/STPA (STAMP = systems-theoretic accident model and processes; STPA = systems-theoretic process analysis) to the German automobile traffic system focusing on the effects of driver assistant systems on drivers. By doing so, the potential hazards caused by technology can be identified.
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
To date, the Trauma Registry (TraumaRegister DGU-® contains data of approximately 100.000 severely injured patients, 65% of which suffered from a road traffic crash. Thus, it is the world's largest data base for severely injured patients. The article describes the development of the registry and explains how it was rolled out over Germany using the established structure of the German Trauma Network (TraumaNetzwerk DGU-®). In addition, this article presents three typical use cases from the fields of quality management, policy making and system-wide interventions, clinical research and injury prevention. In conclusion, the TraumaRegister DGU-® is a well-established tool for various purposes related to the control and reduction of the burden of road injury. Its ongoing expansion to other countries will support the goal of international benchmarking of hospitals and trauma systems.
The number of injured car occupants decreases constantly. Nevertheless, they account for nearly 50% of all fatalities and about 44% of all seriously injured persons in German traffic accidents. Further reductions of casualties require multiple efforts in all parts of traffic safety. In this paper a detailed analysis of the important pre-hospital rescue phase was done. The basis for future improvements is the knowledge about injury causation of car occupants in combination with other corresponding influence factors. For that reason more than 1.200 severe (AIS3+) injuries of frontal car occupants were analyzed. For the most relevant injuries of car occupants multivariate analysis models were created to predict the probability of these injuries in a real crash scenario. In addition to the collision severity different influence factors like impact direction, seat belt usage, age of the occupant, and gender were analyzed. Furthermore, the models were checked regarding the goodness of fit and all results all results were checked concerning their robustness. The prediction models were created on the basis of 5.000 car accidents. Afterwards, the models were validated using 4.000 different car accidents. The prediction of the probability of severe injuries could be used for different applications in the field of traffic safety. One possibility is the implementation of the models in a tool for the on-the-spot diagnosis. The background for the development of such applications is the fact, that there are only limited diagnostic possibilities available at the accident scene. Nevertheless, the rescue forces have to make essential decisions like the alerting of the necessary medical experts, appropriate treatment, the type of transportation and the choice of an adequate hospital. These decisions quite often decide between life and death or influence the long-term effects of injured persons. At this point, indications of expectable injuries could help enormously. To enable even persons with limited technical knowledge to use the tool, a procedure was developed that facilitates the assumption of the given crash severity. Another important possibility for the application of the prediction models is the use for the qualification of information sent by e-call systems.
Introduction: Spine injuries pose a considerable risk to life and quality of life. The total number of road deaths in developed countries has markedly decreased, e.g. in Germany from over 20000 in 1970 to less than 4000 in 2010, but little is known how this is reflected in the burden of spine fractures of motor vehicle users. In this study, we aimed to show the actual incidence of spine injuries among drivers and front passengers and elucidate possible dependencies between crash mechanisms and types of injuries.
The objective of the study is to measure the risk of pedestrian and bicyclist in urban traffic through an analysis of real-world accident data. The kinematics and injury mechanisms for both pedestrian and bicyclists are investigated to find the correlation of injury risks with injury related parameters. For this purpose, firstly 338 cases are selected as a sample from an IVAC accident database based on the In-depth Investigation of Vehicle Accident in Changsha of China. A statistic measurement of the fatality and serious injury risks with respect to impact speed was carried out by logistic regression analysis. Secondly, 12 pedestrian and 12 bicyclist accidents were further selected for reconstruction with MADYMO program. A comparative analysis was conducted based on the results from accident analysis and computer reconstructions for the injury risk, head impact conditions and dynamic response of pedestrians and bicyclists. The results indicate that bicyclists suffered lower risks of severe injuries and fatalities compared with pedestrians. The risks of AIS 3+ injury and fatality are 50% for pedestrians at impact speeds of 53.2 km/h and 63.3 km/h, respectively, while that for bicyclists at 62.5 km/h and 71.1 km/h, respectively. The findings could have a contribution to get a better understanding of pedestrians" and bicyclists" exposures in urban traffic in China, and provide background knowledge to generate strategies for pedestrian protection.
From literature well-known analyzes on risks, hazards and causes of accidents of older drivers are amended by the present study in which a comparison of the specific features of accident causes of older car drivers (older than 60 years) and of younger car drivers (under 25 years) is conducted. Mainly the question is pursued if specific errors, mistakes and lapses are predominant in the two different age groups. The analysis system ACAS (Accident Causation Analysis System) used hereby consists of a sequential system of accident causation factors from the human, the technical and the infrastructural field, whereupon for this study the influence of the human features on the accident development in two different age groups is of interest. ACAS is both an accident model and an analysis and classification system, which describes the human participation factors of an accident and their causes in the temporal sequence (from the perceptibility to concrete action errors) taking into consideration the logical sequence of individual basic functions. In five steps (categories) of a logical and temporal sequence the hierarchical system makes human functions and processes as determinants of accident causes identifiable. The methodology specifically focuses on the use in so-called "In-Depth" and "On-Scene" investigation studies. With the help of the system for each accident participant one or more of five hypotheses of human cause factors are formed and then specified by appropriate verification criteria. These hypotheses in turn are further specified by indicators in such manner that the coding of the causation factors by a code system meets the needs of database processing and are accessible to a quantitative data analysis. The first results of the descriptive comparison of the two age groups concern mainly differences in the functional levels "information admission/perception" (where the elderly drivers have more difficulties than the young ones) and "information processing/evaluation" (where the younger drivers show more problems). Concerning the cognitive function of "planning" the group of younger drivers seems to be more often involved in an accident because of excessive speed.
In 2012 the fifth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Injuries in motorbike accidents in correlation with protective clothes and mechanism of the accident
(2013)
This study deals with a possible connection between safety clothing / accident mechanism and injury severity in a state-wide traffic accident investigation with focus on light and small motorbike-involvement for accidents in the area of the Saarland in which the persons riding the bike have been injured or killed. An interdisciplinary team of medical scientists and engineers collected the medical and technical data as well as all the relevant traces of the accident on scene and in time. During twenty months of data collection a total of 401 cases could be gathered. Grave injuries were more common for the group of heavier motorcycles (>125 ccm). Motorcyclists had been polytraumatized only in the group where the accident was connected with a collision. Significant correlation between protective clothes and injury severity could only be found for protective gloves and protective trousers. The knowledge about mechanism of the accident, protective clothes and severity of injuries can be helpful for the improvement of road and motorcyclists' safety.
Cycle helmets have continued to increase in popularity since their introduction half a century ago. Many studies indicate that overall, head injury can be significantly reduced by wearing them. This study was conducted using two distinct sets of real-world cycling collision data from Ireland, namely cases involving police collision reports and cases involving admission to a hospital emergency department. The analyses sought to simulate and analyse the protective performance of cycle helmets in such collision scenarios, by comparing the Head Injury Criterion score and peak head accelerations, both linear and angular. Cycle collisions were simulated using the specialised commercial software MADYMO. From the simulation results, these key metrics were compared between the same-scenario helmeted and unhelmeted cyclist models. Results showed that the inclusion of bicycle helmets reduced linear accelerations very significantly, but also increased angular accelerations significantly compared to unhelmeted situations. Given the modest protective performance of cycle helmets against angular accelerations, it is recommended that cycle helmet manufacturers and international test standards need to pay more attention to head angular accelerations.
Im Jahr 2004 fand an der Medizinischen Hochschule Hannover die erste ESAR-Konferenz (Expert Symposium on Accident Research) statt. Die Idee einer internationalen Konferenz war aus der Notwendigkeit entstanden, diejenigen Experten zusammen zu bringen, die weltweit tätig sind und Verkehrsunfälle wissenschaftlich analysieren, um ihre Ergebnisse gemeinsam zu diskutieren und einem Zielpublikum von Behördenvertretern, Entwicklungsingenieuren der Automobilindustrie und anderen Wissenschaftlern darzubringen. Die durch Professor Otte initiierte und nun zum vierten Male organisierte Konferenz fand eine breite Akzeptanz und ist mittlerweile Bestandteil einer Konferenzlandschaft mit Zielvorträgen von der Fahrzeugsicherheit bis hin zur Verletzungsanalyse und den Unfallursachen. ESAR kann als wissenschaftliches Kolloquium und Plattform für einen Informationsaustausch der Unfallforscher angesehen werden, die sich speziell mit Methoden der Unfalluntersuchung, mit Verletzungsmechanismen und der Bewertung von Verletzungen, Unfallursachen und anderen Bereichen der statistischen Unfalldatenanalyse befassen. Experten aus den Bereichen der Medizin, der Verkehrspsychologie und der Technik sowie Vertreter zuständiger Behörden kommen hier zusammen, um die Erfahrungen in der Unfallprävention und der Unfallrekonstruktion zu diskutieren und um der Forschung neue Felder zu eröffnen. Neben den Belangen der Europäischen Gemeinschaft werden auch die weltweit zu registrierenden hohen Verletztenzahlen berücksichtigt. Wissenschaftliche Vorträge aus aller Welt tragen dazu bei, geeignete Maßnahmen und Methoden zur Analyse und drastischen Verringerung der Zahl der bei Verkehrsunfällen Getöteten zu entwickeln. Die Zusammensetzung des Teilnehmerkreises dieser wie früherer ESAR-Konferenzen hat längst eine über Europa hinausgreifende Internationalitaet erreicht und bietet daher einen aufschlussreichen Überblick über die verschiedenen Standards bestehender Verkehrssicherheit und unterschiedlichen Unfallszenarien und über die Anforderungen an die Unfallanalysen. Die Ergebnisse langjähriger Forschungsarbeiten in Europa, USA, Australien und asiatischen Ländern beinhalten unterschiedliche infrastrukturelle Zusammenhänge und geben Erkenntnisse über Population, Fahrzeugbestand und Fahrereigenschaften. Derartige Informationen bilden eine exzellente Basis für abzuleitende Empfehlungen und Maßnahmen für die Erhöhung der Verkehrssicherheit international.
Im Rahmen des zweitägigen Kolloquiums "Luftqualität an Straßen 2013" wurden aktuelle Forschungsaktivitäten und Maßnahmen auf dem Gebiet der Luftreinhaltung im Einflussbereich von Straßenbau und Straßenverkehr vorgestellt. Der Tagungsband gibt 14 Fachvorträge und die 4 Beiträge der Posterausstellung wieder.
Entgegen populären Meinungen, welche älteren Kraftfahrern ein generelles Gefahrenpotenzial für die allgemeine Verkehrssicherheit zuschreiben, weisen die Unfallstatistiken eher auf eine besondere Gefährdung dieser Gruppe von Verkehrsteilnehmern hin, woraus sich Forderungen nach einer zielgruppenspezifischen Verkehrssicherheitsarbeit begründen. Kompetentes und damit sicheres Verhalten kann als Ergebnis der Passung zwischen den individuell verfügbaren Ressourcen und den Anforderungen der Umwelt betrachtet werden. Überschreiten die Umweltanforderungen die Verhaltenspotenziale des Individuums, kann es zu Überforderung kommen. Verdeutlichen lässt sich diese Perspektive durch genaue Betrachtung von Verkehrsunfällen unter Beteiligung älterer Kraftfahrer: So spiegeln die aktuellen Unfallstatistiken aus 2008 wider, dass ein großer Teil der Unfälle von Kraftfahrern im Alter über 65 Jahren auf sogenanntes Fehlverhalten in Knoten, wie z.B. Fehler beim Abbiegen, Ein- und Ausfahren in Kreuzungen und Vorfahrtbeachtung, zurückzuführen sind. Diese im Vergleich zu jüngeren Fahrern häufigere Verwicklung Älterer in Unfälle dieser Art legt nahe, dass es in genau diesen Situationen zu einem Ungleichgewicht zwischen individuell verfügbaren Ressourcen und den Anforderungen der Verkehrsumwelt kommt. Beispielsweise könnten in diesen Situationen Beeinträchtigungen der visuellen Wahrnehmungsfähigkeit, verlangsamte Reaktionszeiten oder auch Einschränkungen der Bewegungsausführung zu einer zu langsamen oder auch falschen Entscheidungsfindung oder Handlungsausführung im Straßenverkehr führen. Dieser Perspektive folgend können Maßnahmen zur Erhöhung der Verkehrssicherheit älterer Kraftfahrer zum einen auf Seiten des Individuums ansetzen und dazu beitragen, die Kompetenzen des älteren Kraftfahrers zu erhöhen, zum anderen Bezug auf den Kontext nehmen, indem durch Anpassungen der Bedingungen der Verkehrsumwelt zur Sicherheit " nicht nur " älterer Kraftfahrer beigetragen wird. Personenzentrierte Ansätze zielen dabei auf die Ausschöpfung der individuellen Potenziale zur Aufrechterhaltung, Verbesserung oder auch Wiederherstellung einer sicheren Verkehrsteilnahme bis ins hohe Lebensalter. Diese Ansätze umfassen Trainings- und Rehabilitationsprogramme der Fahrkompetenz gleichermaßen wie verkehrspädagogische Programme, mediale Informationskampagnen oder auch Beratungsmaßnahmen und Screening-Tests. Eine Schlüsselposition kann in diesem Kontext dem (Haus)-Arzt als Experten hinsichtlich Konstitution und Lebensverhältnissen seines Patienten und Vertrauensperson zukommen. In der Regel passen ältere Kraftfahrer ihr Fahrverhalten ihren individuell verfügbaren Kompetenzen an. Auf diese Weise können altersbegleitende oder auch mit Erkrankungen oder Medikamenteneinnahmen einhergehende Veränderungen der körperlichen oder geistigen Leistungsfähigkeit zumeist erfolgreich kompensiert werden. Personenzentrierten Ansätzen kommt jedoch eine besondere Relevanz für den kleinen Anteil älterer Fahrer zu, welche keine oder nur unzureichende Kompensation aufweisen. Kontextorientierte Ansätze beziehen sich auf Maßnahmen, welche eine möglichst optimale Gestaltung der Bedingungen der Verkehrsumwelt auf die Bedürfnisse und Anforderungen älterer Kraftfahrer herbeiführen sollen. Maßnahmen dieser Art zielen zum Beispiel auf eine Entschleunigung des Straßenverkehrs durch Geschwindigkeitsbegrenzungen oder auch bauliche Maßnahmen. Auch die Potenziale moderner Fahrzeugtechnik werden unter dieser Perspektive zur Erhöhung der Verkehrssicherheit älterer Fahrer nutzbar. So können Fahrerassistenz- oder Fahrerinformationssysteme den älteren Fahrer in komplexen Situationen unterstützen. Dabei ist der Nutzen für die Verkehrssicherheit jedoch stark von der Handhabbarkeit und Bedienqualität der technischen Hilfsmittel abhängig. Technologien, welche die Komplexität der Fahrzeugbedienung erheblich erhöhen oder die Aufmerksamkeit vom Straßenverkehr ablenken, können ggf. auch zu einer weiteren Diskrepanz zwischen Anforderungssituation und verfügbaren Kompetenzen beitragen. Neben diesen eher auf die individuelle Verkehrsteilnahme als Autofahrer bezogenen Maßnahmen sind weitere wichtige kontextorientierte Ansatzpunkte in alternativen Mobilitätsvarianten zum Auto, wie in der Verbesserung der Attraktivität von Angeboten des ÖPNV oder auch den Bedingungen für Fußgänger und Radfahrer, zu finden. In diesem Sinne erscheint ein mehrdimensionaler Ansatz für die Gestaltung von Maßnahmen zur Erhöhung der Verkehrssicherheit älterer Kraftfahrer am erfolgversprechendsten. Interventionsansätze sollten sich gegenseitig ergänzen und möglichst sowohl die Ressourcen auf Seiten des älteren Menschen selbst als auch der Umwelt umfassen.
The National Roads Authority in Ireland is responsible for planning and supervision of construction and maintenance works on the National Road network. Its primary function is "to secure the provision of a safe and efficient network of national roads". The population of Ireland has grown rapidly from 3.5 million to 4 million within the past 10 years, and vehicle ownership has also risen rapidly to 2 million vehicles, with 2.2 million drivers. Collisions rates in Ireland are at approximately 1.5 collisions per 1,000 population (in 2002), and 8.4 deaths per 1,000,000 population (in 2003). This ranked 8th out of the 15 countries in the European Union at the time. Ireland- current Road Safety Strategy includes Engineering Targets. These are to complete construction of certain lengths of new motorway, dual carriageway and 2+1 highway, to implement a certain number of accident remedial and traffic calming schemes, and to implement road safety audit on all new schemes. The accident remedial schemes, traffic calming schemes, and road safety audit are all the responsibility of the Road Safety section of NRA. The road safety programme of the NRA is divided into four main areas; a) accident remedial measures at individual sites, b) accident remedial treatment of entire routes, c) traffic calming of towns and villages on main roads, d) road safety audit. Examples of these measures are described. Evaluation of past programmes of single site accident remedial measures show a reduction in collision occurrence at these sites, but the effectiveness and the economic rate of return is decreasing over successive programmes. A similar programme has now been adopted on the rest of the country- road network, on regional and local roads. The programme of remedial treatment of entire routes has only recently started and has not been evaluated. Evaluation of the first programme of traffic calming of towns and villages shows an overall decrease in collisions and their severity, and a small reduction in speed. Road Safety Audit, examining new schemes a number of times during design and after construction, has been standard procedure on the national road network for nearly 6 years. An evaluation is currently underway.
Die EU hat für die Verkehrssicherheit in Europa ein anspruchsvolles Ziel vorgegeben: Bis 2010 soll die Anzahl der im Straßenverkehr Getöteten gegenüber 2000 halbiert werden. Für Deutschland kann eine erfolgreiche Zwischenbilanz gezogen werden: In den letzten 5 Jahren nahm trotz Vergrößerung des Kraftfahrzeugbestandes um 6% die Anzahl der Verkehrstoten um 29% ab, in den vergangenen 10 Jahren ist ein Rückgang um 43% zu verzeichnen. Diese im internationalen Vergleich überdurchschnittlichen Erfolge sind nicht zuletzt auch auf Fortschritte in der Fahrzeugtechnik zurückzuführen, wobei die zunehmende Verbreitung von Systemen der Aktiven Sicherheit wie ABS, BAS, ESP einen entscheidenden Anteil hat. Nach der deutlichen Reduzierung von Fahrunfällen durch ESP-® stehen nun die Auffahrunfälle im Fokus der Sicherheitsentwicklung von Mercedes-Benz. Das Paket aus verbessertem rückwärtigen Signalbild (Adaptives Bremslicht) und Brems-Assistent (BAS) wurde kürzlich durch radarbasierte Bremsassistenz ergänzt (BAS PLUS und PRE-SAFE-®-Bremse). Der Beitrag geht auf Funktion und Wirksamkeit der einzelnen Systeme ein und gibt einen Ausblick in die nähere Zukunft.
The Swedish "Vision Zero" regards road fatalities and severe injuries as unacceptable. The vision is based on this ethical perspective together with a fundament of shared responsibility between the system designers and the road user. The design of the traffic system shall protect the road user from these effects as long as he or she follows the traffic rules. It should be possible to make a mistake without being killed. This policy has, during the first period of the "vision zero" (since 1997) put high priority on road and car design where the purpose has been to develop a forgiving environment. Gradually it has, however, become clear that much more effort has to be focused on the responsibility of the road user. Protecting measures will have limited effect as long as the understanding and acceptance from road users is limited. During the last years, Sweden has gone through several improvements of the driver education and is in the middle of important improvements of road safety education for children in schools. Several EU-projects has contributed to this development. One aspect that has received large international interest is the lay instructed driver training from 16 years of age supervised by parents. This has been in use since 1993. Another is the development of mandatory courses, such as an introduction for the learner and the lay instructor, a "risk awareness" courses dealing specifically with speeding, seat belt use, drunk driving, tiredness, and driving on low friction. The presentation will share some of the "vision zero" fundaments together with the latest experiences, research and development concerning driver education in Sweden.