Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (637) (entfernen)
Schlagworte
- Conference (386)
- Konferenz (382)
- Germany (212)
- Deutschland (209)
- Unfall (188)
- Accident (187)
- Safety (123)
- Sicherheit (122)
- Injury (117)
- Verletzung (117)
Institut
Mit dem Beitrag soll ein Überblick zum aktuellen Bearbeitungsstand der ZTV Ew-StB vermittelt werden. Insbesondere soll auf Neuerungen und Veränderungen hingewiesen und diese inhaltlich kurz beleuchtet werden. Hervorzuheben ist, dass das Regelwerk um die grabenlose Kanalsanierung erweitert wurde und zulässige Abweichungen beim Bau von Entwässerungseinrichtungen geändert wurden. Nach ca. 4 Jahren ist die Überarbeitung und Abstimmung nunmehr weitgehend abgeschlossen.
Die Straßenverkehrsinfrastruktur und der Straßenverkehr müssen sich künftig vielen Herausforderungen stellen. Zu nennen sind hier die Globalisierung, die Nachhaltigkeit, der Anstieg des Güterverkehrs und der technologische, demografische und klimatische Wandel. Die Straßenverkehrsinfrastruktur und der Straßenverkehr müssen sich den prognostizierten und projizierten Veränderungen anpassen. Die BASt betreut in ihrer Strategie "Anpassung der Straßenverkehrsinfrastruktur an den Klimawandel (AdSVIS)" bereits mehr als ein Dutzend Projekte. Diese Strategie soll dazu beitragen, die Verwundbarkeit gegenüber den Folgen des Klimawandels zu mindern bzw. eine leistungsfähige Straßenverkehrsinfrastruktur zu erhalten. Hierfür entscheidend sind nicht nur die durchschnittlichen Änderungen von klimatischen Parametern, sondern mehr noch das Auftreten von Extremwetterereignissen. Geringe Änderungen bei den Mittelwerten können sich aber in hohen Zunahmen bei der statistischen Verteilung der Extremwerte wie z. B. Hitzeperioden, Starkregen, Sturmböen äußern. Der zentrale Punkt der Anpassungsstrategie ist die Risikoanalyse wichtiger Güter- und Transitverkehrsachsen unter Einbeziehung von Seehäfen. Das Ziel dieses Projektes ist die Identifikation, Analyse und Bewertung der Risiken aus den projizierten Klimaänderungen für ausgewählte Streckenabschnitte im deutschen Teil des TEN-T (Transeuropäisches Netz Transport) in Anlehnung an die im ERA-NET ROAD Projekt RIMAROCC entwickelte Methodik. Hierfür werden für die relevanten meteorologischen Parameter Grenzwerte ermittelt, bei deren Überschreitung es für die Elemente der Straßenverkehrsinfrastruktur aus den Bereichen Erdbau, Entwässerung, Straßenbefestigungen, Ingenieurbau und Verkehrstechnik problematisch bzw. kritisch werden kann. Dabei werden nicht nur nach aktuellen Stand der Technik gefertigte Abschnitte des Straßennetzes betrachtet, sondern auch solche älterer Bauweisen und deren Vorkommen im Netz. Über die Fusion der Straßennetzdaten mit regionalisierten Klimaprojektionen werden schließlich die Lokalitäten mit prioritärem Anpassungsbedarf ermittelt. Anschließend werden für die identifizierten Risikobereiche erforderliche Anpassungsmaßnahmen entwickelt, erprobt und hinsichtlich ihrer Wirksamkeit bewertet. Da im Fokus die kostenintensiven Elemente der Straßenverkehrsinfrastruktur mit langer Nutzungsdauer wie Brücken und Straßengründungen stehen, müssen Anpassungsmaßnahmen bereits bei zeitnah anstehenden Erneuerungsarbeiten erfolgen, um die Folgenkosten der Klimaänderung zu senken. Das derzeit laufende Projekt "Risikoanalyse wichtiger Güter- und Transitverkehrsachsen unter Einbeziehung von Seehäfen" stellt eine erste Annäherung an den Aufbau eines Risikomanagements dar. Die hierbei verwendete RIMAROCC-Methodik muss dazu erweitert, weiterentwickelt und validiert werden. Erst dann kann die Risikoanalyse auf Netzebene durchgeführt und die erforderlichen Anpassungsprogramme aufgestellt werden.
Bankette dienen im Wesentlichen der Verkehrssicherheit und dem Schadstoffrückhalt. Sie müssen dauerhaft standfest sein, damit abkommende Fahrzeuge, insbesondere schwere Lkw, nicht einsinken und verunfallen. Zum Grundwasserschutz müssen sie aber auch die Schadstoffe aus dem Straßenabfluss, der im Bankett versickert, zurückhalten. Der Schadstoffrückhalt im Bankett erfolgt vorwiegend durch mechanische Filtration. Diese wird vor allem durch die sandigen und schluffigen Kornfraktionen im Bankettmaterial bewirkt. Ist ihr Anteil aber zu hoch, nehmen die Standfestigkeit und die Tragfähigkeit ab. Es gilt, diese gegenläufigen Anforderungen an die Zusammensetzung von Bankettmaterial zu optimieren. Die Untersuchungsansätze und erste Ergebnisse der dazu beauftragten Forschung werden im Beitrag vorgestellt. Mit den Feinpartikeln aus dem Straßenabfluss und der Vegetation "wachsen" Bankette im Laufe der Jahre auf. Damit der Straßenabfluss nicht behindert wird und Aquaplaning auftritt, müssen Bankette regelmäßig geschält werden. Das bei dieser Reprofilierung anfallende Bankettschälgut ist grundsätzlich als Abfall einzustufen. Die dadurch bedingten Einschränkungen bei der Verwendung oder Verwertung sind in der "Richtlinie zum Umgang mit Bankettschälgut" beschrieben. Die dort aufgezeigten Möglichkeiten werden vorgestellt. Wenn das Bankettschälgut nicht innerhalb des Straßenbauwerks verbleiben kann, sollte es im Sinne der Ressourcenschonung verwertet werden. Bankettschälgut besteht zu circa 90 Masse-Prozent aus mineralischen Bestandteilen, die wieder für Bauzwecke genutzt werden können, wenn es durch eine geeignete Aufbereitung gelingt, die überwiegend pflanzlichen Anteile (Mähgutreste und Wurzeln) deutlich zu reduzieren. Aus einer Forschungsarbeit zu Kosten und Nutzen der Aufbereitung von Bankettschälgut werden der derzeitige Stand dargestellt und Perspektiven für eine werterhaltende Nutzung von Bankettschälgut aufgezeigt.
Europa bedeutet nicht nur eine gemeinsame Währung, sondern auch die Schaffung eines gemeinsamen Marktes verbunden mit dem Abbau von Handelshemmnissen. Dies bedeutet für Produkte aus dem Bereich Straßenausstattung, dass die unterschiedlichen nationalen Anforderungen durch einheitliche europäische Anforderungen ersetzt werden. Nationale Freigaben scheinen daher nicht im Sinne Europas zu sein, da durch zusätzliche nationale Anforderungen Handelshemmnisse eher aufgebaut als abgebaut werden. Die nationalen Freigaben im Bereich Straßenausstattung dienen jedoch nicht dem Aufbau neuer Handelshemmnisse, sondern der Umsetzung europäischer Vorgaben auf nationaler Ebene. Durch die mithilfe der nationalen Freigaben getroffene Vorauswahl können bereits während der Ausschreibungsphase Produkte erkannt werden, die die nationalen Randbedingungen nicht erfüllen beziehungsweise beim Einsatz zu Kompatibilitätsproblemen führen. Um dies zu verdeutlichen, werden exemplarisch für den Bereich Straßenausstattung die europäischen Anforderungen sowie die zusätzlichen Anforderungen aus den nationalen Freigaben für Fahrzeug-Rückhaltesysteme, Verkehrszeichenfolien und Fahrbahnmarkierungen betrachtet.
Im Mittelpunkt der Überlegungen zu Perspektiven einer zeitgemäßen und sicherheitswirksamen Fahranfängervorbereitung steht die Absenkung des weiterhin hohen Anfangsrisikos bei Fahranfängern. Ausgehend von den positiven Erfahrungen mit dem Begleiteten Fahren ab 17 beauftragte das Bundesministerium für Verkehr, Bau und Stadtentwicklung (BMVBS) die Bundesanstalt für Straßenwesen (BASt) mit der Erarbeitung eines Rahmenkonzepts, in dem Entwicklungsperspektiven für weitere Verbesserungen der Vorbereitung von Fahranfängern und wissenschaftlich begründete Maßnahmenvorschläge für die Erhöhung der Fahranfängersicherheit formuliert werden. Zunächst werden die Aufgaben und die Vorgehensweise der Rahmenkonzepterarbeitung sowie die Kriterien für die Ableitung von Maßnahmenprioritäten skizziert. Ausgehend von den Erkenntnissen zur Entwicklung des Unfallrisikos im Verlauf der Fahrkarriere werden im Anschluss die maßgeblichen Ansatzpunkte zur verbesserten Gestaltung eines sicheren Übergangs in die Automobilität aufgezeigt. Zentrale Maßnahmenvorschläge des Rahmenkonzepts werden vorgestellt. Diese beziehen sich auf die Bekämpfung der maßgeblichen Ursachen des erhöhten Fahranfängerrisikos (Fahrerfahrungsdefizit und Einstellungsmängel), die Optimierung bestehender Fahranfängermaßnahmen und die verstärkte Erschließung von Technik und Wissenschaft für das Fahren lernen.
Various kinds of demerit point systems have been developed and implemented in European countries, aimed at tackling repeat offences in road transport by acting as a deterrent and providing sanctioning. The impact of a demerit point system on the number of crashes is often reported to be significant, but temporary. The objective of the EU BestPoint project was to establish a set of recommended practices that would result in a more effective and sustainable contribution of demerit point systems to road safety. A high actual chance of losing the licence and a high perceived chance of losing the licence are basic prerequisites for the effective operation of demerit point systems. For measures applied within the context of a demerit point system, a four-step-approach is recommended: warning letter, driver improvement course, licence withdrawal, rehabilitation course. Further recommendations concern issues like points and offences, e.g. which offences should lead to points, target groups, and the administration of demerit point systems. The final result of the EU BestPoint project is a handbook (van Schagen & Machata, 2012) which provides a concise overview of all recommended practices. The presentation/paper outlines how sustainable safety improvements can be achieved if national demerit point systems are implemented and maintained according to the recommended practices. In addition, potential further steps towards an EU-wide demerit point system (cross-border exchange on points and/or offences) are presented.
The practicability and feasibility of using alcohol ignition interlock devices has been discussed for more than 15 years in Germany. Thereby, judicial issues have been treated conversely. Consensus exists about the fact that the voluntary use of alcohol ignition interlocks is in all areas of possible use recommendable. Great reservation is shown concerning the operation of the devices for DUI (Driving Under Influence) offenders. Main doubts regard the missing legal base for application in such cases and potential circumvention attempts while the need of supportive psychological measures is unquestioned. In 2011, the Ministry of Transport, Building and Urban Affairs entered this topic in its newly released traffic safety programme as a matter of future research. Almost in parallel, the Federal Highway Research Institute (BASt) launched an alcohol ignition interlock project for DUI offenders. The study at hand aimed at developing a comprehensive programme concept for the use of alcohol ignition interlocks as additional measure to psychological rehabilitation for DUI offenders. Expert surveys serve as input for the establishment of a widely accepted innovative concept for nationwide implementation. By means of a pilot trial, the added value of using a combination of structural (alcohol interlock) and individual (psychological measure) intervention for DUI offenders to the existing countermeasure system should be studied. In addition, selection criteria for DUI offenders eligible for future programme participation should be defined. The majority of the experts evaluate the introduction of alcohol ignition interlocks as a good option to enhance traffic safety. The possibility of early psychological rehabilitation is emphasized in the process. Those who do not approve alcohol ignition interlock usage estimate the amount of offenders eligible for such programmes too small. The survey also revealed that legal regulations for issuing an alcohol interlock restricted licence to DUI offenders is missing. Hence, a possible amendment to the German Driving Licencing Regulation was developed within the project. Consultations with the Ministry of Transport, Building and Urban Affairs and the Ministry of Justice disclosed the need for a change of the road traffic law before an amendment to the existing regulations may be put into force. At least, the person responsible in the Ministry of Justice developed a proposal for the law section that needs revision. All in all, it became clear within the process of the project that a field trial in Germany is still a distant vision. Nevertheless, all institutions involved are motivated to deal with the matter further on in order to pave the way for a soon start of the pilot trial.
In Germany, courses for the restoration of the fitness to drive after licence revocation are provided for different offender groups (alcohol, drug and demerit point offenders). Providers of these courses are by law required to prove the effectiveness of the applied course programs. For the evaluation of effectiveness, the Federal Highway Research Institute (BASt) established specific "Reference Values" in 2002. The objective of the study at hand was to collect valid data in order to renew the old-established Reference Values from 2002. Additionally, data collection aimed at initializing Reference Values for drug offender programs. Over 66,000 drivers were analysed regarding their traffic probation in the three years after licence reinstatement. Offenders were assigned to an offender group (alcohol, drugs and demerit point offenders) based on the reason for prior licence revocation. Different indicators were used as criteria for re-offending: new alcohol or drug records, culpable accident involvement and repeated licence revocation. For each of the offender groups, frequency distributions regarding these indicators were calculated. Frequencies of recidivism are highest for the group of demerit point offenders. Compared to the Reference Values of this group from 2002, frequencies of re-offending increased. Conversely, re-offence frequencies of alcohol offenders are halved compared to the data from 2001. The analysis of the re-offence frequencies of drug offenders reveals an equal amount of re-offenders as in the alcohol offender group. The collected data serve as a good base for renewal of the old-established Reference Values and may be applicable as comparative data for future evaluations The results reveal significant differences between recent data and earlier studies. These may occur due to improvements of the applied programmes, but also due to situational changes, e.g. increased enforcement levels and expansion of the catalogue of offenses which lead to demerit points.
The 6th RFP project DRUID aimed at supporting European transport policy makers by suggesting scientifically based recommendations to combat impaired driving. The main DRUID objectives were: 1. In-depth analysis of the problem situation with regard to DUI/DUID in Europe; 2. Assessment of prevalence and accident risks of DUI/DUID on the basis of epidemiological and experimental studies; 3. Evaluation of oral fluid screening devices and cost-benefit analysis of a strengthened drug driving enforcement; 4. Development of a classification system for medicines; 5. Evaluation of driver rehabilitation schemes and strategies of licence revocation; 6. Assessment of the effectiveness of new prescribing and dispensing guidelines for medicines; 7. Ddevelopment of policy recommendations on the basis of DRUID results. All in all, the DRUID results revealed that prevalence of psychoactive substance consumption, DUI/DUID, enforcement levels and legal strategies are very heterogeneous in European countries. Nonetheless, DRUID derives general recommendations as base for national solutions.
The DRUID expert consensus established recommendations on how to define limits for psychoactive substance use in traffic. The European DRUID project established a group of experts who are members of national working groups for defining analytical and/or risk thresholds. This group evaluated the results of DRUID, scientific literature and the experience of representatives of several EU Member States and Norway in determining cut-off levels. 1. Cut-offs should be defined for the most frequently used psychoactive substances; 2. In order to achieve compliance of the population towards cut-off regulations, they should be clear and comprehensible, pointing out the risks when used in traffic; 3. Thus, the definition of cut-offs should be based on current scientific knowledge; 4. The lowest substance concentration exerting an effect on driving should be preferred instead of the lowest limit of quantification/ detection; 5. For all psychoactive substances including alcohol, the same risk should be accepted. When a country intends to determine per se cut-off levels, several considerations have to be taken into account. From a scientific point of view, the same risk should be anticipated for all psychoactive substances including alcohol. Nevertheless, every cut-off discussion should address the question if the DRUID approach, to determine risk thresholds equivalent to alcohol limits, is feasible for the respective case.
In dem Beitrag präsentieren die Autoren einige laufende und geplante Forschungsvorhaben der Bundesanstalt für Straßenwesen (BASt), die wesentliche Bestandteile der Forschungslinie (FL) Q5 "Innovationen: Von der Idee in die Praxis" der mittelfristigen Forschungsplanung der BASt darstellen. Bei den konkreten Projekten geht es um die Entwicklung eines geeigneten Bewertungsverfahrens für Innovationen, um das Sichten neuer Forschungsideen aus denen neue Forschungsvorhaben resultieren können, um Nutzung von numerischen Methoden für die Entwicklung neuer Baustoffe und Bauweisen, sowie um den Aufbau einer geeigneten Untersuchungsinfrastruktur.
Ungefähr 20 Jahre nach der Einführung der Bauproduktenrichtlinie (Richtlinie 89/106/EWG, BauPR) wurde im April 2011 im Amtsblatt der Europäischen Union das Nachfolgewerk, die Verordnung (EU) Nummer 305/2011 (Bauproduktenverordnung, BauPVO), veröffentlicht. Zielsetzung der Überarbeitung war der Wunsch nach Klarstellung, nach Erleichterungen für Kleinere und Mittlere Unternehmen bei der Anwendung, aber insbesondere der Wunsch nach mehr Vertrauen in die CE-Kennzeichnung. Mit der Herausgabe einer unmittelbar verbindlichen Verordnung hat die Europäische Kommission den Stellenwert dieses Dokuments verdeutlicht und wirkt damit zugleich auf eine einheitliche Anwendung im europäischen Wirtschaftsraum hin. Darüber hinaus enthält die BauPVO im Detail eine Vielzahl von Änderungen gegenüber der BauPR, sodass eine zweistufige Einführung mit einer vollständigen Wirksamkeit aller Artikel der BauPVO zum 01. Juli 2013 vorgesehen ist, um den Wirtschaftsakteuren eine Frist zur Vorbereitung und Umstellung zu gewähren. Bestehende harmonisierte Normen für Bauprodukte haben auch nach dem 1.7.2013 weiterhin Bestand und müssen erst im Zuge der turnusmäßigen Überarbeitung an die Vorgaben der BauPVO angepasst werden. Unabhängig davon sind die Hersteller von Bauprodukten verpflichtet, anstelle des Konformitätsnachweises eine Leistungserklärung abzugeben. Diese kann auf der Basis der vorhandenen Dokumentation, z.B. der Erstprüfung erstellt werden.
In der Vergangenheit stiegen die Verkehrsbelastung und der Anteil des Schwerverkehrs auf deutschen Straßen und Autobahnen nahezu stetig. Dies wird sich auch in der Zukunft fortsetzen. Um auch zukünftig Mobilität gewährleisten zu können, sind Bauweisen mit maximaler Nutzungsdauer und minimalen Erhaltungsaufwendungen erforderlich. In Deutschland werden Betonfahrbahndecken als unbewehrte direkt befahrene Betonfahrbahnplatten mit Querfugen in regelmäßigen Abständen gefertigt und für Nutzungsdauern von 30 Jahren konzipiert. Die Querfugen stellen dabei den schwächsten Bereich in der Konstruktion dar. Betonfahrbahndecken können auch als Durchgehend Bewehrte Betonfahrbahndecke gefertigt werden. Dabei stellt sich ein freies Rissbild mit schmalen Plattenstreifen ein. Um eine Querkraftübertragung zu sichern, wird die Rissöffnungsweite durch die Anordnung einer durchgehenden Längsbewehrung beschränkt. Die Erfahrungen zeigen, dass mit dieser Bauweise eine längere Nutzungsdauer und ein höherer Fahrkomfort erreicht werden und weniger Erhaltungsmaßnahmen erforderlich sind. Durchgehend Bewehrte Betondecken eignen sich besonders gut für eine Asphaltüberbauung, da es keine Querfugen als Störstellen gibt. Diese Komposition hat das Potenzial für eine Nutzungsdauer von 50 Jahren und erfordert geringere Kosten, wenn man den gesamten Lebenszyklus betrachtet. Um baupraktische Erfahrungen zu sammeln, wurde im Jahr 2011 auf der Bundesautobahn (BAB) A 94 bei Forstinning in Bayern eine Versuchsstrecke eingerichtet. Diese besteht aus drei Abschnitten von je etwa 4 km Länge: Durchgehend Bewehrte Betondecke mit DSH-V-Überbauung, unbewehrte Betondecke in Plattenbauweise mit DSH-V-Überbauung und unbewehrte Betondecke in Plattenbauweise mit Grinding-Oberfläche. Erste Ergebnisse bezüglich Rissbildung, Bewegungen an den Endspornen, Haftverhalten des Blacktopping und der Schallmessungen liegen vor.
Die Reduzierung des Straßenverkehrslärms ist in den letzten Jahren zunehmend in den Fokus der Forschungsaktivitäten gerückt. Laut einer Studie des Umweltbundesamts fühlen sich in Deutschland circa 60 % der Bevölkerung durch den Straßenverkehrslärm belästigt. Diese Zahl ist seit vielen Jahren konstant. Ein Grund dafür sind die steigenden Verkehrsmengen. Neben den bekannten gesundheitlichen Beeinträchtigungen wurden in den letzten Jahren auch zunehmend negative Auswirkungen des Verkehrslärms auf die Stadtentwicklung beobachtet. Die Bundesanstalt für Straßenwesen koordiniert seit über 10 Jahren die durch das Bundesministerium für Wirtschaft und Technologie geförderten Verbundprojekte "Leiser Straßenverkehr". Partner aus Industrie und Forschung verfolgen das gemeinsame Ziel, effektive Lösungen für eine Lärmreduzierung zu erarbeiten. In den letzten Jahren ist es gelungen, die Wirkmechanismen der Lärmentstehung im Zusammenspiel Reifen-Fahrbahn detailliert zu beschreiben und Anforderungen für eine dauerhafte Lärmreduzierung zu formulieren. In der Straßenbautechnik wurden Regelbauweisen lärmtechnisch optimiert und neue Bauweisen entwickelt. Zusammen mit Projektpartnern konnte die Firma Continental Reifen Deutschland GmbH Pkw- und Lkw-Reifen akustisch optimieren. Ein zentrales Ziel im Verbundprojekt Leiser Straßenverkehr 3 ist die Weiterentwicklung eines Simulationsmodells, um künftig unter Berücksichtigung verschiedener Einflussgrößen aus Reifen und Fahrbahn Geräuschprognosen zu ermöglichen.
Für die Instandsetzung von schadhaften Betonfahrbahnplatten mittels "Heben und/oder Festlegen" werden in zunehmendem Maße Injektionsmaterialien aus Kunststoff verwendet. Aktuell existieren für die Prüfung und Bewertung derartiger Materialien mittels straßenbauspezifischer Kennwerte jedoch noch keine hinlänglichen Erfahrungen und Prüfvorschriften. In Laborversuchen wurden nunmehr geeignete Prüfungen und Auswertalgorithmen entwickelt und zweckgerichtete Festigkeitskennwerte an ausgesuchten Materialien bestimmt sowie erste Anforderungswerte formuliert. Zudem wurden die Wirksamkeit und die Dauerhaftigkeit von Unterpressungen im Hinblick auf das verwendete Injektionsmaterial in Praxisversuchen überprüft. Aus den Ergebnissen der Tragfähigkeitsmessungen ließ sich vorerst folgern, dass durch das Unterpressen von Fahrbahnplatten die Tragfähigkeits- und Lagerungsbedingungen signifikant verbessert werden können. Unterschiede in der kurzfristigen Wirksamkeit - im Hinblick auf das verwendete Injektionsmaterial - konnten hierbei nicht explizit deduziert werden. Vielmehr zeigte sich, dass die Dauerhaftigkeit maßgeblich von den vorliegenden Randbedingungen, das heisst, faktisch von der richtigen Auswahl des Materials abhängt.
Die neuen TL/ZTV/TP Fug-StB
(2013)
Eine Betondecke kann nur so gut sein wie ihre Fugen und Fugenfüllsysteme. Funktionierende Fugen sind daher ein wesentlicher Bestandteil der Betonstraße. Nur mit funktionierendem Fugenfüllsystem kann die prognostizierte Lebensdauer einer Betondecke von mindestens 30 Jahren erreicht werden. In diesem Sinne wurden im Jahre 2001 die ZTV Fug-StB 01) eingeführt, um durch technische Vorgaben einen hohen Standard bei der Herstellung von Fugen zu gewährleisten. Aufgrund notwendiger Neuerungen, technischer Weiterentwicklung bei der Herstellung von Fugenmassen und -profilen sowie der Umsetzung der Europäischen Normen in das Deutsche Regelwerk war nach 10 Jahren nun eine Überarbeitung notwendig. Der Entwurf der neuen ZTV Fug-StB gliedert sich nach dem Kapitel "Allgemeines" in vier Teile für die unterschiedlichen Fugenfüllsysteme. Die neuen ZTV Fug-StB sind für Beton- und Asphaltflächen ebenso wie für Verkehrsflächen auf Bauwerken, Pflasterflächen, Schienenfugen und Riss-Sanierungen anwendbar. Es werden neu entwickelte Fugenkonstruktionen behandelt. Die Bedeutung funktionierender Fugen und Fugenfüllsysteme wird anhand aktueller Themen sehr deutlich. Derzeit werden verstärkt Schäden bei Fugen an neuen Betondecken, insbesondere Flankenablösungen und Versprödungen der Fugenvergussmasse beobachtet. Hier werden mögliche Schadensursachen ermittelt mit dem Ziel, über die komplexen Wirkungszusammenhänge ein Fugenfüllsystem mit Heißvergussmassen zu entwickeln, das den technischen Anforderungen an das Gesamtsystem "Betonstraße" gerecht wird.
Enhanced protection of pedestrians and cyclists remains on the focus. Besides infrastructural and behavioral aspects it is necessary to exploit technical solutions placed on motorized vehicles. Accident research needs reliable data as well as national road accident statistics. Changing the view on seriously injured road users is one of the challenges which will substantially contribute to the optimization on future traffic safety. The missing accuracy in the definition of personal injury has a detrimental effect on making cost efficient road safety policy which is not only focused on fatal accidents. The European commission requested that, starting in 2015, all EU member states provide more detailed data on the injury status of road casualties, with special regard to the group of seriously injured. Conventional accident data will always be essential. But to obtain detailed data about driver behavior in real traffic situations further data sources are required. These could be EDR data, data from electronic control units, data from traffic surveys and traffic counting, naturalistic diving studies and field operational tests. Gaining insight into normal as well as critical driver behavior will enable accident researchers to deduct functions estimating the increase or decrease of accident risk associated with certain behaviors or vehicle functions. Also with view to the introduction of highly automated driving functions in the future such data is urgently needed. Computer simulation based tools to estimate the benefits of active safety systems are another step on the way towards the safety assessment of automated driving. It is now the duty of the scientific community to ask the right questions, to develop a methodology and to merge all these data sources into a common framework for the assessment of future traffic safety innovations.
The current paper reports on the results of a pilot study aiming to investigate the effect of mobile telephone use on the driving performance of 5 amateur and 5 professional drivers. Their driving acuity was tested through a driving simulator. Analysis and interpretation of the results occurred comparing the drivers' driving performance while talking, reading messages and writing a message on the mobile phone (intervention time) with the drivers' driving performance engaged in no activity (control time). The variables affected by the mobile phone were the "steering", the "lane offset" and the "duration of lane offset". Moreover, the drivers involved in a car crash in the last five years appeared to differ from those who were not involved in a crash in both "lane offset" and "following distance". The results of this pilot study will inform the design of a large experimental study on 50 professional and 50 amateur drivers.
Although the annual traffic accident statistics published by the national police is available in public, the detailed traffic accident data has not been released in Korea. Recently the Ministry of Land, Infrastructure and Transport recognized the importance of in-depth accident data to enhance road traffic safety and initiated a research project to establish a collection of the detailed accident data. The main objective of the project is a feasibility study to establish KIDAS (Korea In-Depth Accident Study). Within this project, three university hospitals which are located in mid-size cities have been selected to collect accident data. Annually, more than 500 cases of accidents have been collected from the in-patient's interviews and diagnosis. Unlike GIDAS (German In-Depth Accident Study), currently on-site investigation can"t be performed by the Korean police. The only available data is patient medical records, patient's description of accident circumstances and the damaged vehicle. Occasionally the police provide the accident investigation reports containing very brief information on accident causation and vehicle safety. In a first step, the concept of KIDAS is to adopt the format of iGLAD (Initiative for the Global Harmonization of Accident Data) for harmonization. Since the currently collected accident information is extremely limited compared with GIDAS, the other sources of data and calculations such as KNCAP vehicle data, pc-crash simulations, vehicle registration information, insurance company data are utilized to complete the iGLAD template. Results from KIDAS_iGLAD and the cases of assessment of active safety devices such as AEBS, ESC, and LDWS will be evaluated.
Road accidents are typically analyzed to address influences of human, vehicle, and environmental (primarily infrastructure) factors. A new methodology, based on a "Venn diagram" analysis, gives a broader perspective on the probable factors, and combinations of factors, contributing both to the occurrence of a crash and to sustaining injuries in that crash. The methodology was applied to 214 accidents on the Mumbai-Pune expressway. Factors contributing to accidents and injuries were addressed. The major human factors influencing accidents on this roadway were speeding (30%) and falling asleep (29%), while injuries were primarily due to lack of seat belt use (46%). The leading infrastructure factor for injuries was impact with a roadside manmade structure (28%), and the main vehicle factor for injuries was passenger compartment intrusion (73%). This methodology can help identify effective vehicle and infrastructure-related solutions for preventing accidents and mitigating injuries in India.
Injury severity of e.g. pedestrians or bikers after crashes with cars that are reversing is almost unknown. However, crash victims of these injuries can frequently be seen in emergency departments and account for a large amount of patients every year. The objective of this study is to analyze injury severity of patients that were crashed into by reversing cars. The Hannover Medical School local accident research unit prospectively documented 43,000 road traffic accidents including 234 crashes involving reversing cars. Injury severity including the abbreviated injury scale (AIS) and the maximum abbreviated injury scale (MAIS) was analyzed as well as the location of the accident. As a result 234 accidents were included into this study. Pedestrians were injured in 141 crashes followed by 70 accidents involving bikers. The mean age of all crash victims was 57 -± 23 years. Most injuries took place on straight stretches (n = 81) as well as parking areas (n = 59), entries (n = 36) or crossroads (n = 24). The AIS of the lower extremities was highest followed by the upper extremities. The AIS of the neck was lowest. The mean MAIS was 1.3 -± 0.6. The paper concludes that the lower extremities show the highest risk to become injured during accidents with reversing cars. However, the risk of severe injuries is likely low.
Ruptures and dissections of the thoracic and abdominal aortic vessel caused by traffic accidents are rare but potentially life-threatening injuries. They can occur by blunt trauma via seat belt or dashboard injury. The study aimed at evaluating the overall mortality, morbidity, neurological disorders, and differences in operative procedures of open repair and stenting. It shows that, with a change and improvement in diagnostic tools and surgical approach, mortality and morbidity of blunt aortic injuries were significantly reduced. Still an immediate life-threatening injury early diagnosis via multiple-slice and scans and surgical repair with minimally invasive stents showed excellent short-time results for selected patients.
Assessment of the effectiveness of Intersection Assistance Systems at urban and rural accident sites
(2015)
An Intersection Collision Avoidance System is a promising safety system for accident avoidance or injury mitigation at junctions. However, there is still a lack of evidence of the effectiveness, due to the missing real accident data concerning Advanced Driver Assistance Systems. The objective of this study is the assessment of the effectiveness of an Intersection Collision Avoidance System based on real accidents. The method used is called virtual pre-crash simulation. Accidents at junctions were reconstructed by using the numerical simulation software PC-Crashâ„¢. This first simulation is called the baseline simulation. In a second step the vehicles of these accidents were equipped with an Intersection Collision Avoidance System and simulated again. The second simulation is called the system simulation. In the system simulation two different sensors and four different intervention strategies were used, based on a time-to-collision approach. The effectiveness of Intersection Collision Avoidance System has been evaluated by using an assessment function. On average 9% of the reviewed junction accidents could have been avoided within the system simulations. The other simulation results clearly showed a change in the principal direction of force, delta-v and reduction of the injury severity.
The main focus of the benefit estimation of advanced safety systems with a warning interface by simulation is on the driver. The driver is the only link between the algorithm of the safety system and the vehicle, which makes the setup of a driver model for such simulations very important. This paper describes an approach for the use of a statistical driver model in simulation. It also gives an outlook on further work on this topic. The build-up process of the model suffices with a distribution of reaction times and a distribution of reaction intensities. Both were combined in different scenarios for every driver. Each scenario has then a specific probability to occur. To use the statistical driver model, every accident scene has to be simulated with each driver scenario (combinations of reaction times and intensities). The results of the simulations are then combined regarding the probabilities to occur, which leads to an overall estimated benefit of the specific system. The model works with one or more equipped participants and delivers a range for the benefit of advanced safety systems with warning interfaces.
Event data recorders (EDRs) are a valuable tool for in-depth investigation of traffic accidents. EDRs are installed on the airbag control module (ACM) to record vehicle and occupant information before, during, and after a crash event. This study evaluates EDR characteristics and aims at better understanding EDR performance for the improvement of accident reconstruction with more reliable and accurate information regarding accidents. The analysis is based on six crash tests with corresponding EDR datasets.
The study aimed at estimating the impact of pedelecs (with an assumed higher speed than bicycles) on the traffic accident severity in Germany for different penetration rates. The analysis shows that in many real situations (68%) an electrical support of bicycles has no influence on the sequence of accident events. Taking into account a number of unreported "single bicycle accidents", the adoption of similar traffic behavior and similar age distribution, the authors determined a shift of 400 former slightly to seriously injured cyclists in Germany per year. Overall this would be an increase of approximately 2.3% in case of 10% of pedelec penetration with the pessimistic assumption of 10 km/h speed increase although first natural driving studies predict a much lower average speed increase of pedelecs. The hypothesis verbalized in the initial question whether a higher distribution of pedelecs will result in more severe accidents in Germany is not verified. The study shows that electrical support didn"t result in higher collision speed in general. In many accident situations, the speed of pedelecs has only a minor influence on the accident severity. Further research focusing on a possible change of driver behavior especially in new target groups (elderly people) will be needed.
The Traffic Accident Research Institute at University of Technology Dresden investigates about 1,000 accidents annually in the area around and in Dresden. These datasets have been summarized and evaluated in the GIDAS (German Accident In-Depth Study) project for 13 years. During the project it became apparent that the specific traffic situation of a covert exit of a passenger car and an intersecting two-wheeler involves a high risk potential. This critical situation develops in a large part due to the lack of visibility between the driver and the intersecting bike. In this paper the accident avoidance potential of front camera systems with lateral field of view, which allows the driver to have an indirect sight into the crossing street area will be presented.
In North America, frontal crash tests in both the regulatory environment and consumer-based safety rating schemes have historically been based on full-width and moderate-overlap (40%) vehicle to barrier impacts. The combination of improved seat-belt technologies, notably belt tensioning and load limiting systems, together with advanced airbags, has proven very effective in providing occupant protection in these crash modes. Recently, however, concern has been raised over the contribution of narrower frontal impacts, involving primarily the vehicle corners, to the incidence of fatality and serious injury as a result of the potential for increased occupant compartment intrusion and performance limitations of current restraint systems. Drawing on data documented in the National Automotive Sampling System (NASS)/ Crashworthiness Data System (CDS) for calendar years 1999 to 2012, the present study examines the characteristics of existing and proposed corner crash test configurations, and the nature of real-world collisions that approximate the test environments. In this analysis, particular emphasis is placed on crash pulse information extracted from vehicle-based event data recorders (EDR's).
Analysis of pedestrian leg contacts and distribution of contact points across the vehicle front
(2015)
Determining the risk to pedestrians that are impacted by areas of the front bumper not currently regulated in type-approval testing requires an understanding of the target population and the injury risk posed by the edges of the bumper. National statistics show that approximately 10% of all accident casualties are pedestrians, with 20% to 30% of these pedestrian casualties being killed or seriously injured. However, the contact position across the front of the bumper is not recorded in national statistics and so in-depth accident databases (OTS, UK and GIDAS, Germany) were used to examine injury risk in greater detail. The results showed that some injury types and severities of injuries appear to peak around the bumper edges. Although there are sometimes inconsistencies in the data, generally there is no evidence to suggest that the edges of the bumper are less likely to be contacted or cause injury.
Many safety-relevant tasks in control or diagnostics require binary choices such as "conflict versus separation" in air traffic control, "normal versus pathological" when interpreting x-ray pictures, or "permitted versus forbidden" when inspecting airport security scans. Deciders often are uncertain, but nevertheless required to decide between two alternatives, that is, they have not only to decide upon an action, but also about the admissible level of uncertainty. If the accepted level of judgment certainty is not taken into account, the sequence of decisions does not capture the full picture of the underlying decision process. Differences in judgment certainty are relevant, because they reflect not only the adequacy of the human-machine interface that is evaluated, but also the differences in expertise of the decider and the requirements of the actual situation or task. Therefore, capturing both judgment certainty and discrimination performance is essential. A comparison of different human-machine-interfaces (for air traffic control) is used to illustrate a methodological approach, which allows for integrated analyses of decision processes based on receiver-operator-characteristics and practical guidelines for the evaluation of human-machine-interfaces for safety-relevant operation procedures are provided.
Detailed anthropometric data of pregnant women have been collected and used in the development of a computational model of the pregnant occupant model "Expecting". The model is complete with a finite element uterus and multi-body fetus, which is a novel feature in the models of this kind. The computational pregnant occupant model has been validated and used to simulate a range of impacts. The strains developed in the utero-placental interface are used as the main criteria for fetus safety. Stress distributions due to inertial loading of the fetus on the utero-placental interface play a role on the strain levels. Inclusion of fetus model is shown to significantly affect the strain levels in the utero-placental interface. This series of studies has led to the design of seatbelt features specifically for the pregnant women to enable them use the seatbelt correctly and comfortably.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
In general the passive safety capability is much greater in newer versus older cars due to the stiff compartment preventing intrusion in severe collisions. However, the stiffer structure which increases the deceleration can lead to a change in injury patterns. In order to analyse possible injury mechanisms for thoracic and lumbar spine injuries, data from the German Inâ€Depth Accident Study (GIDAS) were used in this study. A twoâ€step approach of statistical and caseâ€byâ€case analysis was applied for this investigation. In total 4,289 collisions were selected involving 8,844 vehicles, 5,765 injured persons and 9,468 coded injuries. Thoracic and lumbar spine injuries such as burst, compression or dislocation fractures as well as soft tissue injuries were found to occur in frontal impacts even without intrusion to the passenger compartment. If a MAIS 2+ injury occurred, in 15% of the cases a thoracic and/or lumbar spine injury is included. Considering AIS 2+ thoracic and lumbar spine, most injuries were fractures and occurred in the lumbar spine area. From the case by case analyses it can be concluded that lumbar spine fractures occur in accidents without the engagement of longitudinals, lateral loading to the occupant and/or very severe accidents with MAIS being much higher than the spine AIS.
Die UNECE Regelung R58 regelt die Beschaffenheit und die Installation von Heckunterfahrschutzsystemen an schweren Güterkraftfahrzeugen, deren Ziel die Verbesserung der Kompabilität zwischen Pkw-Frontstrukturen und Lkw-Hecks ist. Dennoch verunglücken laut amtlicher Unfallstatistik allein in Deutschland rund 30 Pkw-Insassen in Heckauffahrunfällen auf Lkw tödlich, da diese Vorrichtungen hinsichtlich Einbauhöhe und Steifigkeit den Anforderungen des realen Unfallgeschehens nicht genügen. Das Ziel dieser Studie ist eine quantitative Abschätzung der möglichen Reduzierung der Verletzungsschwere mit Hilfe eines statistischen Modells, die durch eine Anpassung der geltenden Bestimmungen und die damit verbundenen technischen Veränderungen des bereits vorgeschriebenen Heckunterfahrschutzes zu erreichen wäre. In einer Nutzen-Kosten-Analyse wird die Wirtschaftlichkeit dieser Modifizierungen mit einem idealen Notbremsassistenten verglichen. Die Untersuchung orientiert sich dabei an den aktuell in der UN-ECE WP29/GRSG in Genf diskutierten Vorschlägen zur Anpassung der ECE-R58. Das verwendete ordinale Probit-Modell stellt einen Zusammenhang zwischen der Verletzungsschwere im auffahrenden PKW und erklärenden Größen her, in diesem Fall der kinetischen Energie des unterfahrenden Pkws und der strukturellen lnteraktion zwischen Lkw-Heck und Pkw-Front. Diese Maßnahmen könnten demnach 53 - 78% der Getöteten sowie 27 - 49% der Schwerverletzten bei diesen Unfallkonstellationen reduzieren, was pro Jahr 20 Getöteten und 95 Schwerverletzten entsprechen würde. Somit würde eine Modifikation einer bestehenden passiven Schutzmaßnahme an jährlich 100.000 neuzugelassenen Lkw und Anhängern bereits 20 Getötete adressieren. Im Vergleich dazu müssten jährlich 3 Millionen Pkw mit zusätzlicher Sensorik und Aktuatorik für einen idealen Notbremsassistenten ausgestattet werden, um im Idealfall alle Heckauffahrunfälle von Pkw auf andere Pkw oder Lkw und damit 53 Getötete zu vermeiden. Daher fällt auch das Nutzen-Kosten-Verhältnis deutlich zugunsten des verbesserten Heckunterfahrschutzes aus.
Regarding to the German road traffic licensing regulations it is mandatory to have a light system using a bicycle in public traffic. All attached components must be approved. The admission requires additional restrictions such as a dynamo as energy source with a nominal voltage of 6 V. Batteries are only allowed in addition to this. To adopt the German bicycle regulation to the state of art of an energy efficient lighting, additional power sources such as a battery respectively rechargeable batterie should be evaluated. The project will propose amendments for German Road Traffic Regulations and technical requirements.
Im von der DG Home (CIPS Program) geförderten Projekt "SecMan " Security Manual for Road Infrastructures" wurde ein vierstufiges Verfahren zur Identifikation kritischer Straßeninfrastrukturen, ihre Bewertung hinsichtlich diverser von Menschen verursachter Gefahren sowie die Bestimmung effektiver Schutzmaßnahmen entwickelt. Diese Ergebnisse wurden in einem ganzheitlichen "best-practice" Handbuch zusammen getragen, welches einen trans-nationalen Sicherheitsmanagement-Ansatz für Betreiber und Eigentümer von Straßeninfrastrukturen in Europa ermöglicht. Im Folgenden wird die entwickelte Methodik vorgestellt, ausgehend von der Bewertung der Netzkritikalität über die Attraktivität und Vulnerabilität eines Bauwerks hin zu einer Bewertungsmethodik für die Auswahl geeigneter Schutzmaßnahmen.
In the project SECMAN " SECurity MANual " a simple four-step procedure for the identification of critical road infrastructures, assessment of these infrastructures regarding various man-made threats and the determination of effective protection measures was developed. These methodologies are summarized and combined into a comprehensive best-practice manual which allows for a trans-national structured and holistic security-risk-management approach for owners and operators of road infrastructures in Europe. This paper presents the developed methodology starting from the assessment procedures of a network's criticality over an object's attractiveness and vulnerability to the selection process of appropriate protection measures.
The paper describes the development of transitions between different safety barriers in Germany but also in the context of the European standardization. In the paper practical and impact test expriences with transitions are shown. In view of the sheer number of theoretically possible combinations of safety barriers, the demand for testing every transition, even if the connecting safety barriers differ only slightly, appears to be economically unacceptable. On the other hand the experience from accidents and also from failed impact tests shows that transitions can be a risk to traffic safety. Therefore criteria for the distinction between transitions (impact test required/impact test unnecessary) are explained. In order to distinguish transitions which do not have to be impact-tested from those that require impact tests, criteria were developed and formulated.
Improving the security of critical road infrastructure is a major task for owners and operators of tunnels and bridges in the European TEN-T Network (Trans-European Networks of Transport) (European Parliament and Council 1996). Up to now, there has not been a systematic procedure for identifying and assessing critical infrastructure objects and selecting appropriate protection measures. The EC FP7 project SeRoN for the first time presents an innovative methodology in order to support road owners and operators in handling this complex task. This paper describes the methodology and project results in detail by giving an introduction into its practical application.
According to an investigation in March 2008 by the Federal Ministry of Transport, Building and Urban Affairs (BMVBS) about 14,000 truck parking spaces are missing in the near of motorways in Germany. Beside constructional enlargement of rest areas, intelligent traffic systems ought to be used to detect automatically the occupancy rate of rest areas and to provide better demand management and also to achieve an increase of capacity of truck parking spaces. The essay describes the newly developed control procedure "Compact parking", which is currently under development by German Federal Highway Research Institute (BASt). The method achieves that a number of trucks are parking in a compact way, side by side and without a driving lane between them. With the help of dynamic displays above the parking rows, the drivers receive the needful information to park their vehicle in a parking row, in which other trucks have the same or an earlier departure time. This system is able to increase the rest area capacity in short-term, more quickly than constructional enlargement of rest areas.
Due to the publication of guidelines in Germany the possibility exists to offer analytical designed construction works within an alternative proposal. But the extent to which the test specimen production influences the design relevant properties (for the same asphalt mixture) is not sufficiently investigated at present. Objective of this research project was to determine the design relevant asphalt properties by tests and do comparative considerations on two selected locations within the renewal of a federal trunk road (Germany). For the comparative consideration of the design relevant asphalt properties mixture samples were taken during paving and afterwards drill cores were taken at the same locations. Fatigue tests and tests to determine the stiffness were conducted with the Indirect Tensile Test (ITT). Then design calculations having regard to the test results were performed. At this different bearing conditions of the asphalt package were considered. The calculated fatigue conditions were comparative evaluated and they are presented and discussed in this paper.
Tempered road system
(2014)
The road performance is strongly influenced by climatic conditions. Winter conditions have massive impact on traffic security but also pavement lifetime decreases as an effect of temperature variation during wintertime and summertime. Heating and cooling of a pavement is a possibility to work against these impacts. To discuss the boundary conditions for an efficient construction and operation of a tempered road system a feasibility study has been made. The study shows the feasibility and identifies thermal energy buffering as a main challenge. When thinking of a fully regenerative operation of a large tempered road system (e.g. 20.000 m-²) the storage volume has to be too large for an economic and structurally engineered satisfactory solution. However, the location dependent usage of natural geothermal storage possibilities and as well smart alignment and construction promises a feasibility realization.
Various climate projections predict changing climatic parameters like temperature, precipitation, wind speed etc. for Germany. This could have severe impacts on road transport infrastructure as well as road traffic itself. At the Federal Highway Research Institute (Bundesanstalt für Straßenwesen (BASt) a strategy was developed to adapt roads and engineering structures to the impacts of climate change. The strategy "Anpassung der Straßenverkehrsinfrastruktur an den Klimawandel / Adaptation of the road infrastructure to climate change (AdSVIS)" comprises currently about 15 projects. On the basis of the identification of the hazards and the combination of the climate and road network data, the road transport infrastructure which might be affected is to be determined. Adaptation measures are to be developed for the identified risk areas and assessed as to their effectiveness. Special attention is given to international cooperation since climate change is a truly global challenge.
Das Symposium umfasste folgende Beiträge: Who is afraid of more bicycle use? (Dijkstra,A); Safety of main roads in built-up-areas (Huber,CA); Safety of rural roads (Hehlen,P); Behavioural adaptation to vehicle design (Pfafferott,I); Adaptation to safety measures: there is still a lot to do (Levelt,PBM); Using sociological data to define target groups the speed limit's case (Barjonet,P); Definition of target groups for safety campaigns (Michalik,C); Influence speed choise (Clough,WS); Automatic speed management systems: great safety potential? (Oei,HL); Road accident risk factors in childhood and adolescence (Assailly,JP); What makes the young driver risky? (Hatakka,M); Influencing young driver's attitude by short-term reduction in traffic-risk factors (Johansen,HJ); Border crossing traffic and traffic safety (Elsner,A); Border-crossing traffic and security (Lukaschek,H); Enhancing police road accident data with information from other sources: the role of hospital data (Hopkin,JM); Exposure of unprotected road users (Thulin,H); Misuse of restraint systems for childs and adults (Wenaell,J); Emergency medical services systems (EMMS) and the care of traffic casualities in the Federal Republic of Germany (Kuehner,R).
Radfahren - aber sicher!
(1989)
Bei der Veranstaltung, die am 16. und 17. November 1987 zu dem Thema "Radfahren - aber sicher!" in Wiesbaden stattfand, ging es darum, dem Sicherheitsbedürfnis des zunehmenden Radfahrverkehrs in der Bundesrepublik Deutschland gerecht zu werden, andererseits aber auch das nicht unproblematische Verhältnis zwischen der Radfahrerpopulation auf der einen und den übrigen Verkehrsteilnehmergruppen auf der anderen Seite auszuleuchten. In der jüngeren Vergangenheit wurden Klagen geäußert wie etwa die, dass sich die Radfahrer ihr eigenes Gesetz schafften. Von den Betroffenen wird dagegengehalten, dass die den Straßenverkehr betreffenden Gesetze und Verordnungen aus dem Blickwinkel des Kraftfahrers heraus gemacht worden seien und ein Verstoß dagegen für Radfahrer oft die naheliegendste Möglichkeit sei, einer Selbstgefährdung zu entgehen. Aus diesem Grunde wurde die Thematik in dem von der Deutschen Verkehrswacht gemeinsam mit der Bundesanstalt für Straßenwesen (BASt) und dem Bundesverkehrsministerium durchgeführten Symposium aus unterschiedlichster Sicht angesprochen. Vertreten war sowohl die Unfallforschung, die Straßenplanung, die Fahrzeugtechnik und die Polizei wie auch die Interessenvertreter der Rad- und der Autofahrer. Von vornherein war klar, dass ein Symposium dieser Art nicht dazu angetan sein konnte, "Patentlösungen" zu erarbeiten. Ziel der Veranstaltung war es vielmehr, das gegenseitige Verständnis der unterschiedlichen Verkehrsteilnehmergruppen füreinander zu wecken bzw. zu fördern. Dabei wurde deutlich, dass auch die Problematik des "Rollenwechsels" keineswegs frei von Schwierigkeiten ist: Das Verhalten des möglicherweise überwiegenden Teils der Verkehrsteilnehmer ist nicht so sehr an einem Grundwissen und ein Grundverhalten gebunden, als vielmehr von der Art der jeweiligen Verkehrsteilnahme abhängig.
This study aimed at prediction of long bone fractures and assessment of lower extremity injury mechanisms in real world passenger car to pedestrian collision. For this purpose, two pedestrian accident cases with detail recorded lower limb injuries were reconstructed via combining MBS (Multi-body system) and FE (Finite element) methods. The code of PC Crash was used to determine the boundary conditions before collision, and then MBS models were used to reproduce the pedestrian kinematics and injuries during crash. Furthermore, a validated lower limb FE model was chosen to conduct reconstruction of injuries and prediction of long bone fracture via physical parameters of von Mises stress and bending moment. The injury outcomes from simulations were compared with hospital recorded injury data and the same long bone fracture patterns and positions can be observed. Moreover, the calculated long bone fracture tolerance corresponded to the outcome from cadaver tests. The result shows that FE model is capable to reproduce the dynamic injury process and is an effective tool to predict the risk of long bone fractures.
Cycling supports the independence and health of the aging population. However, elderly cyclists have an increased injury risk. The majority of injured cyclists is victim of a single-sided accident, an accident in which there is no other party involved. The aim of the project "Safe and Aware on the bicycle" is to develop guidelines for an advisory system that is useful in preventing single-sided accidents. This system is able to support the elderly cyclist; enabling the cyclist to timely adapt his cycling behaviour and improve cycling safety and comfort. For the development of such advisory system the causes of singles accidents and the wishes of the elderly cyclist must be known. First step to obtain this insight was a literature survey and an GIDAS research. Unfortunately accidentology research with GIDAS did not give the full understanding of the pre-crash situations and (especially the behaviour related) factors leading to the accident. The second step was consultation of elderly cyclist through a questionnaire (n=800), in-depth interviews (n=12) and focus group sessions (n=15). This offered complementary information and a much better understanding of the behavioural aspects. Results concern the behaviour in traffic and identify specific physical (i.e. problems looking backwards over the shoulder) and mental issues. Furthermore, the needs and wishes for support in specific cycling situations were identified. In conclusion; The GIDAS results together with the information obtained contacting the elderly cyclists enabled setting up requirements for an advisory system, which is useful in preventing single-sided accidents.
Since a number of human models have been developed it appears sensible to use these models also in the accident analysis. Especially the understanding of injury mechanisms and probably even injury risk curves can be significantly improved when interesting accidents are reconstructed using human body models. However, an important limitation for utilising human models for accident reconstruction is the effort needed to develop detailed FE models of the accident partners or to prepare the human model reconstruction by running physical accident reconstructions. The proposed approach for using human models for accident reconstruction is to use simplified and parametric car models. These models can be adapted to the crash opponents in a fast and cost effective way. Although, accuracy is less compared to detailed FE models, the relevant change in velocity can be simulated well, indicating that the computation of a detailed crash pulse is not needed. Two frontal impact test accidents that were reconstructed experimentally and using the parametric car models are indicating sufficient correlation of the adapted parametric car models with the full scale crash reconstructions. However, further developments of the parametric models to be capable for the use in lateral impacts and rear impacts are needed. For the PC Crash simulation runs the output sampling rate is too large to allow sufficient analysis. In addition the performance appears to be too general.
This study aimed at developing an injury estimation algorithm for AACN technologies for Germany and compared them to findings based on Japanese data. The data to build and to verify the algorithm was obtained from the German in-depth Accident Database (GIDAS) and split into a training and a validation dataset. Significant input variables and the generalized linear regression model to predict severe injuries (ISS>15) were selected to maximize area under the receiver operating characteristic curve (AUC). Probit regression with the input parameter multiple impact, delta v, seatbelt use and impact direction gave the largest AUC of 0.91. Sensitivity of the algorithm was validated at 90% and specificity at 76% for an injury risk threshold of 2%. It appears that no major differences between Japan and Germany exist for injury estimation based on delta v and impact direction. However, far side impact and multiple crash events appear to be associated with a larger risk increase in the German data.
This study aimed at comparing head Wrap Around Distance (WAD) of Vulnerable Road User (VRU) obtained from the German in-depth Accident Database (GIDAS), the China in-depth Accident Database (CIDAS) and the Japanese in-depth Accident Database (ITARDA micro). Cumulative distribution of WAD of pedestrian and cyclist were obtained for each database (AIS2+) showing that WAD of cyclists were larger than the ones of pedestrians. Comparing three regions, the 50%tile WAD of GIDAS was larger than that of both Asian accident databases. Using linear regression that might predict WAD of pedestrians and cyclists from Impact speed and VRU height, WADs were calculated to be 206cm/219cm (Pedestrian/Cyclist) for GIDAS, 170cm/192cm for CIDAS and 211cm/235cm for ITARDA. In addition, this study may be helpful for reconsideration of WAD measurement alignment between accident reconstruction and test procedures.
Pedestrians represent about 20% of the overall fatalities in Europe- road traffic accidents. In this paper a methodology is proposed to understand why the numbers are so high, especially in the south of Europe and particularly in Portugal, . First a detailed statistical analysis using Ordinal Logistic Regression model (OLR) was applied to the gathered data from all Portuguese accidents with victims in the period 2010-2012. In a second stage accident reconstruction computational techniques using pedestrian biomechanical models are used to evaluate the accident conditions that lead to the injuries, such as the speed and the impact location. For biomechanical injury criterions, the AIS (Abbreviated Injury Scale), the HIC (Head Injury Criterion) and other injury criterions based on the resulting accelerations in the pedestrian's body are used. The statistical model reported that there were several predictors that significantly influenced the pedestrian injury severity in the event of a road accident, such as Pedestrian's age, Pedestrian's gender, Vehicle Design/Category or Driver's gender. The use of injury scales and biomechanical criterions in in-depth investigation of road accidents, such as AIS, can significantly improve the quality of the reconstruction process.
The current Brussels EU Regulation No. 1235/2011, valid from May 30, 2012, has introduced an European Tyre Label with wet grip index G classes from A to G for passenger car tyres C1, light commercial vehicles tyres C2 and heavy truck- and bus tyres C3. Every wet grip class for each vehicle category has a defined band of numerical values for the wet grip index G. The legislated wet grip values G in this EU- Regulation are very low. The measured braking distances and corresponding impact speeds of the test vehicles are showing very critical results. Regulation No. 1235/2011 of the European Parliament and the Council for Type Approval of Vehicles (EU) should be changed in such a way, that for C1-tyres (normal passenger cars tyres) the minimum wet grip index G is 1.25. All C2-tyres (light commercial vehicles tyres) should at least meet a minimum wet grip index of G = 1.1. All C3-tyres (heavy trucks and buses tyres) should at least meet a minimum wet grip index of G = 0.95. Due to the missing lower limits for G in the wet grip class F for C1, C2 and C3 tyres according to Commission Regulation (EU) No. 1235/2011, officially valid from 30 May 2012, a tyre-to-road coefficient of adhesion in the extreme of 0 (zero) is legally permitted. This is an apparent flaw in above cited EU Regulation, which causes a potential danger to the road traffic safety for all motor vehicles in Europe with such tyres. The wet grip class F has to be removed urgently from said EURegulation, since a direct liability of the responsible EU-Commission can not be excluded.
The declining trend since 1991 in the number of killed people was broken in 2011 when overall 4 009 people died in traffic accidents in Germany. The question arises if there is a stagnating trend of fatalities in Germany in future? By breaking down the accidents with casualties towards a monthly view one can see a decreasing trend of fatalities in the warmer months especially since 2009. When comparing against winter months higher deviations are observed. In December 2011 an increase of 191 traffic deaths were registered (181 in 2010 compared to 372 in 2011). Further analyses of different accident influences were evaluated and their possibility of drastic change from one year to the other was determined. As seen weather- and environmental conditions are one of the major contributing factors and are one of the causes for the increased number of fatalities. To support the underlying assumption a model had been created to calculate the number of traffic deaths on a daily basis approach. As an input, road conditions projected through weather parameters and also different driving behaviors on weekdays or holidays were used. As a result, estimates of daily fatality with up to 75% precision can be achieved out of the 2009, 2010 and 2011 data. Further on it shows that weather and street conditions have a high influence on the overall resulting number of traffic accidents with casualties, and especially to the number of fatalities. Hence it is estimated that approximately 3 300 people were killed in traffic accidents in Germany in 2013 which would be again a reduction of another 13% compared to 2012. Therefore an answer to the question will be that the decreasing trend in traffic fatalities in Germany somehow is not broken when environmental conditions are included in national statistics. Their effects will become more visible in future accident statistics and it is estimated variances of 5% to 8% of the annual number of traffic fatalities in Germany will be seen.
Today's volumes of traffic require more and more responsibility from each individual road user in their interactions. Those who drive motor vehicles have the singular obligation to minimise the risk of accidents and hence the severity of injuries, particularly with a view to the most vulnerable road users such as motor bikes, bikes and pedestrians. Since responsible and pro-active driving depends first and foremost on the visual information relayed by our eyes and the visual channel this requires good command of the traffic and all-round visibility from our driver's seat. Granted that human error can never be fully excluded, improving visibility around the car is nevertheless an urgent priority. To do so, we need to rate visibility in the most realistic driving situations. Since the existing visibility metrics and methodology are not applicable to real-life driving situations, this study aimed at developing a new visibility rating methodology based on real-life accident scenarios. On the basis of the cases documented by the accident research project, this study analysed criteria indicative of diminishing visibility on the one hand and revealing some peculiarities in connection with the visibility issue on the other. Based on the above, the project set out to develop a rating methodology allowing to assess all-round visibility in various road situations taking into account both driver and road geometries. In this context, the assessment of visibility while turning a corner, crossing an intersection and joining traffic on a major road (priority through route) is of major importance. The first tests have shown that critical situations can be avoided by adapting the relevant geometries and technical solutions and that significant improvements of road safety can be derived therefrom.
For the estimation of the benefit and effect of innovative Driver Assistance Systems (DAS) on the collision positions and by association on the accident severity, together with the economic benefit, it becomes necessary to simulate and evaluate a variety of virtual accidents with different start values (e.g. initial speed). Taken into account the effort necessary for a manual reconstruction, only an automated crash computation can be considered for this task. This paper explains the development of an automated crash computation based on GIDAS. The focus will be on the design of the virtual vehicle models, the method of the crash computation as well as exemplary applications of the automated crash computation. For the first time an automated crash computation of passenger car accidents has been realized. Using the automated crash computation different tasks within the field of vehicle safety can be elaborated. This includes, for example, the calculation of specific accident parameters (such as EES or delta-V) for various accident constellations and the estimation of the economic benefit of DAS using IRFs (Injury Risk Functions).
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
The changed focus in vehicle safety technology from secondary to primary safety systems need to evolve new methods to investigate accidents, high critical, critical and normal driving situations. Current Naturalistic Driving Studies mostly use vehicles that are highly equipped with additional measuring devices, video cameras, recording technology, and sensors. These equipped fleets are very expensive regarding the setup and administration of the study. Due to the great rarity of crashes it is additionally necessary to have a high distribution and a homogeneous distribution of subject groups. At the end all these facts are leading to a very expensive study with a manageable number of data. Smartphones are becoming more and more popular not only for younger people. Contrary to traditional mobile phones they are mostly equipped with sensors for acceleration and yaw rates, GPS modules as well as cameras in high definition resolution. Additionally they have high-performance processors that enable the execution of CPU-intensive tools directly on the phone. The wide distribution of these smartphones enables researchers to get high numbers of users for such studies. The paper shows and demonstrates a software app for smartphones that is able to record different driving situations up to crashes. Therefore all relevant parameter from the sensors, camera and GPS device are saved for a given duration if the event was triggered. The complete configuration is independently adjustable to the relevant driver and all events were sent automatically to the research institute for a further process. Direct after the event, interviews with the driver can be done and important data regarding the event itself are documented. The presentation shows the methodology and gives a demonstration of the working progress as well as first results and examples of the current study. In the discussion the advantages of this method will be discussed and compared with the disadvantages. The paper shows an alternative method to investigate real accident and incident data. This method is thereby highly cost efficient and comparable with existing methods for benefit estimation.
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
India is one of the leading countries reporting highest road accidents & related injuries. TMARG (Tata Motors Accident Research Group) has been recording crashes in association with M/s. Lokamanya Medical Foundation since 2011 with M/s, Amandeep Hospitals since Aug 2013. This study has highlighted some accident types not discussed extensively in literature. Trucks to Truck impacts " Cabin interaction with overhanging loadbody structures and Offset underside impacts for passenger vehicles are seen in significant numbers. The paper discusses these in more detail including severity.
Within the COST Action TU1101 the working group WG 1 is dealing with acceptance criteria and problems in helmet use while bicycling concerning conspicuity, thermal stress, ventilation deficits and other potential confounding. To analyze the helmet usage practice of bicyclists in Europe a questionnaire was developed in the scope of working group 1 to collect relevant information by means of a field study. The questionnaire consists of some 66 questions covering the fields of personal data of the cyclist, riding und helmet usage habits, information concerning the helmet model and the sensation of the helmet, as well as information on previous bicycle accidents. A second complementary study is conducted to analyze if the use of a bicycle helmet influences the seating geometry and the posture of cyclists when riding a bicycle and if the if the helmet vertically limits the vision. For this purpose cyclists with and without helmets were photographed in real world situations and relevant geometrical values such as the decline of the torso, the head posture of the upper vertical vision limit due to the helmet were established from the photos. The interim results of the field studies which were conducted in Germany by the Hannover Medical School are presented in this study. Some 227 questionnaires were filled out, of which 67 participants had used a helmet and 42 of the 227 participants have had a bicycle accident before. For the analysis of the riding position and posture of the cyclist over 40 pictures of riders with a helmet and over 240 pictures of riders without a helmet were measured concerning the seating geometry to describe the influence of using a bicycle helmet. Some results in summary: From the riders interviewed with the questionnaire only 11% of the city bike riders and 12% of the mountain bike riders always used the helmet, while 38% of the racing bike riders and 88% of the e-bike-riders always used the helmet. The helmet use seems not to change the sensation of safety of cycling compared to the use of a car. The arguments for not wearing a helmet are mostly stated to be the short distance of a trip, high temperatures or carelessness and waste of time. The reasons for using a helmet are stated to be the feeling of safety and being used to using a helmet. Being a role model for others was also stated to be a reason for helmet use. Concerning the sensation of the helmet 9% of the riders reported problems with the field of vision when using a helmet, 57% saw the problem of sweating too much, and 10% reported headaches or other unpleasant symptoms like pressure on the forehead when using the helmet. The analysis of the seating posture from the pictures taken of cyclists revealed that older cyclists generally have a riding position where the handle bar is higher than the seat (0-° to 10-° incline from seat to handlebar), while younger riders had a higher variance (between -10-° decline and 20-° incline). Further, elderly riders and riders with helmets seem to have a more upright position of the upper body when cycling. The vertical vision limit due to the helmet is determined by the front rim of the helmet (mostly the sun shade). Typical values here range from 0-° (horizontal line from the eye to the sun shade) to 75-° upwards, in which elderly riders tend to have a slightly higher vertical vision limit possibly due to the helmet being worn more towards the face.
The paper gives an overview of the recent (mostly 2012) figures of killed bus/coach occupants (drivers and passengers) in 27 Member States of the European Union as reported by CARE. The Evolution of the figures of bus/coach occupants killed in road accidents urban, rural without motorway and on motorways from 1991 to 2010 in 15 Member States of the EU supplements this information. More detailed are the figures reported for Germany by the Federal Statistics. The paper displays long-term evaluations (1957 to 2012) for killed, seriously and slightly injured occupants in all kinds of buses/coaches. Midterm evaluations (1995 to 2012) of the figures of fatalities and casualties are displayed for different busses according to their identification of road using as coaches, urban buses, school buses, trolley buses and "other buses". To be able to compare the evolutions of the safety of vehicle occupants it is customary to use different risk indicators. Calculations and illustrations for three often used indicators with their development over time are given: fatalities, seriously injured and slightly injured per 100,000 vehicles registered, per 1 billion (109) vehicle-kilometres travelled and per 1 billion (109) person-kilometres. These indicators are shown for occupants of cars, goods vehicles and buses/coaches. For the period from 1957 until 2012 it is obvious, that for all three vehicle categories analysed there was a clear long-term trend towards more occupant safety in terms of casualties per vehicles registered and per vehicle mileage. This was most significant for car occupants but it can be seen for bus/coach occupants and goodsvehicle occupants as well. Figures of killed occupants and of casualties related to person-kilometres are calculated and displayed for the shorter period 1995 to 2012. Here it becomes obvious that the bus/coach is still the safest mode of transport for the occupants of road vehicles. Graphs for the casualty risk indices still show significantly higher risks for car occupants despite the corresponding curve moved sustainable downwards. It is remarkable, that the risks of being killed or injured for the occupants of urban buses is growing whereas the corresponding risk for the occupants of coaches in line traffic tends downwards. The article ends with a short comparison and discussion of the risk indicators which are actually published for the occupants (driver and passengers) of cars and the passengers of buses/coaches, railroads, trams and airplanes. The interpretation of such information depends on the perception and it seems that for a complete view not only one indicator should be used and the evolutions of the indicator values during longer periods (as displayed with examples in the paper) should also be taken into account.
Introduction: The method of causation analysis applied under the German accident survey GIDAS, which is based on Accident Causation Analysis System (ACAS) focuses on an on-scene data collection of predominantly directly event-related causation factors which were crucial in the accident emergence as situational resulting events and influences. The paradigm underlying this method refers to the findings of the psychological traffic accident research that most causally relevant features of the system components human, infrastructure and vehicle technology are found directly in the situation shortly before the accident. This justifies the survey method which is conducted directly at the accident (on-scene), shortly after the accident occurrence (in-time) with the detection of human-related causes (in-depth). Human aspects of the situation analysis that interact and influence the risk situations shortly before the collision are reported as errors, lapses, mistakes and failures in ACAS in specific categories and subcategories. Thus methodically ACAS is designed primarily for the collection of accident features on the level of operational action, which certainly leads to valid findings and behavioral causes of accidents. The enhancement by means of Moderating Conditions concerns the pre-crash phase in different levels: strategical, tactical and operational.
Accident simulation and reconstruction for enhancing pedestrian safety: issues and challenges
(2015)
The enhancement of pedestrian safety represents a major challenge in traffic accidents. This study allows a better understanding of the issues in pedestrian protection. It highlights the potential of in-depth studies in identifying relevant crash parameters interfering in the pedestrian safety. A computational simulation tool was developed to reconstruct pedestrian real-world crashes. A sample of 100 in-depth accident cases was reconstructed from two sources: 40 crashes provided by IFSTTAR-LMA and 60 crashes from CASR. To exemplify the methodology, two accident cases from each database were illustrated. A description of the sample of crashes was presented including the travel and impact speed of the vehicle, the driver reaction, the pedestrian walking speed, the scene configuration with the eventual obstacles, etc. This detailed description is pointing to the major factors affecting the limits of pedestrian safety systems.
This work aimed for getting the main features of accidents involving Light Goods Vehicles (LGV), using accident cases collected in the In-Depth Accidents Studies built up at IFSTTAR-LMA (France), in order to analyse thoroughly the proceedings of these accidents and identify the major factors for the different types of LGV. This work was based on the analysis of 88 accident cases involving LGV with a Maximum Authorised Mass inferior to 3.5 tonnes. In particular kinematics reconstruction of these accidents were performed to calculate the average impact speeds and to better understand the compatibility problems between LGV and antagonist vehicles. Specific features have been reviewed to pick up problems concerning safety, maintenance, loading, LGV design: general conditions of the accident, vehicle features, and passive safety. The main results of this study are presented in this paper.
While it is important to track trends in the number of road accidents in different countries using national statistics, there is a need for data with more detailed information, so called in-depth accident data. For this reason, several accident data projects emerged worldwide in recent years. However, also different data standards were established and so comparative analysis of international in-depth data has been very hard to conduct, so far. This is why the project iGLAD (Initiative for the Global Harmonization of Accident Data) was established and created the prerequisites for building up a standardized dataset out of the common denominator of different in-depth accident databases from Europe, USA and Asia. In the first phase, the project received funding from ACEA to compile an initial database. To accomplish this, a suitable data scheme has been defined, a pilot study has been conducted as proof of concept and the recoding of the first common data base has been initiated. Also, to prepare the project for its self-supporting continuation in the next years, a business model has been developed. This paper reports the history and status of the project, the current challenges and the creation of a capable consortium to maintain the data. In mid-2014, the initial database containing 1550 cases from 10 different countries will be completed and a first detailed view on this data will be possible.
In 2014 the sixth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Topics of this report are: Road construction (highways, interstate roads, urban by-passes, cycle tracks, construction sites, level crossings removal), traffic management systems, road tunnel equipment, harmonisation of vehicle regulations, accident statistics and accident research, passive vehicle safety, active vehicle safety , automotive environmental protection and rescue systems.
EEVC Status report
(2001)
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
An approach to the standardization of accident and injury registration systems (STAIRS) in Europe
(1998)
STAIRS is a European Commission funded study whose aim is to produce a set of guidelines for a harmonised, crash injury database. The need to evaluate the effectiveness of the forthcoming European Union front and side impact directives has emphasised the need for real world crash injury data-sets that can be representative of the crash population throughout Europe. STAIRS will provide a methodology to achieve this. The ultimate aim of STAIRS is to produce a set of data collection tools which will aid decision making on vehicle crashworthiness as well as providing a means to evaluate the effectiveness of safety regulations. This paper will disseminate the up-to-date findings of the group as they try to harmonise their methods. The stage has been reached where studies into the diverse methods of the UK, French and German systems of crash injury investigation have been undertaken. An assessment has already been made of the relationships between the three current systems in order to define the areas of agreement and divergence. The conclusions reached stated that there were many areas that are already closely related and that the differences were only at the detailed level. With the emphasis on secondary safety and injury causation, core data sets were decided upon, taking into account: vehicle description, collision configuration, structural response of vehicles, restraint and airbag performance, child restraint performance, Euro NCAP, pedestrian and vehicle occupant kinematics, injury description and causation. Each variable was studied objectively, the important elements isolated and developed into a form that all partners were agreeable on. A glossary of terms is being developed as the project progresses which includes ISO standards and other definitions from the associated CAREPLUS project, which addresses the comparability of national data sets. A major consideration of the group was the data collection method to be employed. The strengths and weaknesses of each study were investigated to obtain a clear idea of which aspects offered the best way forward. The quality of this information and transference into a common format, as well as the necessary error checking systems to be employed have just been completed and are described. In tandem with this area of study the problem of the statistical relationship of each sample to the national population is also being investigated. The study proposes a mechanism to use a sample of crash injury data to represent the national and international crash injury problem
A means of assessing the passive safety of automobiles is a desirable instrument for legislative bodies, the automobile industry, and the consumer. As opposed to the dominating motor vehicle assessment criteria, such as engine power, spaciousness, aerodynamics and consumption, there are no clear and generally accepted criteria for assessing the passive safety of cars. The proposed method of assessment combines the results of experimental safety tests, carried out according to existing legally prescribed or currently discussed testing conditions, and a biomechanical validation of the loading values determined in the test. This evaluation is carried out with the aid of risk functions which are specified for individual parts of the body by correlating the results of accident analysis with those obtained by computer simulation. The degree of conformance to the respective protection criterion thus deduced is then weighted with factors which take into account the frequency of occurrence and the severity of the accident on the basis of resulting costs. Each of the test series includes at least two frontal and one lateral crash test against a deformable barrier. The computer-aided analysis and evaluation of the simulation results enables a vehicle-specific overall safety index as well as partial and individual safety values to be determined and plotted graphically. The passive safety provided by the respective vehicle under test can be defined for specific seating positions, special types of accident, or for individual endangered parts of the body.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
In der Öffentlichkeit wird allgemein angenommen, dass Massenunfälle aufgrund schlechter Straßen- und Sichtverhältnisse passieren, vor allem bei Nebel. Statistisch gesehen ereignet sich das Ineinanderfahren zahlreicher Fahrzeuge aber wesentlich häufiger bei guter Sicht. Was sind die Gründe? Dieser Frage wurde auf einem Presseseminar des Bundesministeriums für Verkehr am 14. und 15. September 1994 in Kassel nachgegangen. Dabei wurde das Phänomen des Massenunfalls aus den verschiedensten Blickwinkeln betrachtet: Was ist ein Massenunfall? Wie arbeitet die Polizei? Welche Probleme haben Rettungsdienste und Notfallmediziner? Was geht im Kopf der beteiligten Autofahrer vor sich? Gibt es technische Hilfen und wirksame Lernsysteme?
Um ein zuverlässiges Straßennetz aufrechtzuerhalten, ist es notwendig, neue innovative Ansätze in das Erhaltungsmanagement der Brückenbauwerke im Bundesfernstraßennetz zu integrieren und weiterzuentwickeln. Ergänzend zu den turnusmäßigen Bauwerksprüfungen nach DIN 1076 wird daher ein adaptives Konzept bereitgestellt, das es ermöglichen soll zum einen Zustandsveränderungen frühzeitig zu erfassen und zu bewerten und zum anderen mit Hilfe von erfassten Einwirkungen und Widerständen zukünftige Zustandsentwicklungen zu prognostizieren. Die zu konzipierenden Systeme setzen sich im Wesentlichen aus der Datenerfassung mit Hilfe von Sensorik und den zur echtzeitnahen Verwendung und Bewertung notwendigen Modellen zusammen. Im Rahmen mehrerer Forschungsprojekte wurden einzelne Bausteine eines solchen adaptiven Systems erarbeitet.
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
T. DÜNCHHEIM erörtert in seinem Einführungsvortrag zu "Die Stellung der Gemeinden im Straßenrecht" die kommunalen Gestaltungsspielräume hinsichtlich ihres Satzungsrechts, das sich auf -§ 19 StrWG NRW stützen lässt. Er schildert die Auswirkungen dieser Gestaltung auf das Straßen- und Straßenverkehrsrecht, die letztlich Ausfluss der gemeindlichen Selbstverwaltungsgarantie sind. Dabei problematisiert er die Abgrenzung zwischen straßenrechtlichem Gemeingebrauch und Sondernutzung sowie die Bedeutung der rechtlichen Ausgestaltung des Straßen- und Straßenverkehrsrechts. Hierbei wird die Anwendung des -§ 45 StVO durch die Gemeinden einer kritischen Analyse unterzogen. A. NETTER schildert in seinem Beitrag "Aktuelle Rechtsfragen der Ortsdurchfahrten" die Gremienstruktur im Straßenwesen und den Einfluss des Europarechts, des Bundes- und Landesstraßenrechts sowie den Ortsdurchfahrtenrichtlinien auf das Straßenwesen. Er stellt dabei die Folgen der Aufhebung der Radwegbenutzungspflicht sowie die aus der Straßenbaulast folgende Entwässerungsverpflichtung der Straßenbaulastträger und ihre Umsetzung in den Gemeinden dar. U. WEGNER berichtet in ihrem Beitrag "Aktuelle Entwicklungen des Verbandsklagerechts" über die Auswirkungen europäischer Richtlinien auf das Umweltrecht. In diesem Zusammenhang wird eine wegweisende Entscheidung des BVerwG erörtert, welche die direkte Anwendung des Art. 9 Abs. 3 AK zum Gegenstand hat. Trotz der Einführung einer bundesrechtlichen Verbandsklage in -§ 64 BNatSchG sei das Problem der Wahrung von Allgemeininteressen nicht gelöst, da diese Norm die Interessen des Umweltschutzes nicht hinreichend zu schützen vermöge. Der Beitrag "Inanspruchnahme öffentlicher Wege durch TK-Unternehmen" von U. STELKENS, stellt eine differenzierte Auseinandersetzung mit dem TKG-Wegerecht dar. Er konstatiert, dass die Bestimmungen des TKG im Wesentlichen auf den Normen des Telegraphenwegegesetz (TWG) basieren. Daher bestehen Spannungsverhältnisse und Reibungsflächen zwischen den verschiedenen Abschnitten des TKG, da das TKG und das TWG unterschiedliche Ziele verfolgen. Beispielsweise seien die -§ 77a bis -§ 77e TKG nicht auf die -§ 68 bis -§ 77 TKG abgestimmt worden. Der abschließende Beitrag "Fachplanerische Auswirkungen des Umweltschadensgesetzes" von M. PETERSEN widmet sich der Frage, ob und welche Auswirkungen das Umweltschadensgesetz auf das Fachplanungsrecht hat. Zunächst wird allgemein herausgearbeitet, dass das Umweltschadensgesetz nicht Schadensersatz- oder Ausgleichsleistungen eines geschädigten Dritten bezweckt; vielmehr sollen Umweltschäden vermieden und die Wiederherstellung geschädigter Umweltgüter erreicht werden. Die Frage, ob und inwieweit das Umweltschadensgesetz Auswirkungen auf das Fachplanungsrecht hat, hängt davon ab, ob die Haftungstatbestände des -§ 3 Abs. 1 USchadG einschlägig sind.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
When the EEVC proposed the full-scale side impact test procedure, it recommended that consideration should be given to an interior headform test in addition. This was to evaluate areas of contact not assessed by the dummy. EEVC Working Group 13 has been researching the parameters of a possible European headform test procedure in four phases. Earlier stages of the research have been presented at previous ESV conferences. The conclusions from these have suggested that the US free motion headform should be used in any European test procedure and that it should be a free flight test, not guided. This research has now culminated in proposals for a European test procedure. This paper presents the proposed EEVC side impact interior headform test procedure, giving the rationale for the test and the first results from the validation phase of the test protocol.
The development of tyre- and truck-manufacturers leads to the direction to introduce wide base single tyres (size 495/45R22,5) instead of twin tyres on the driving axle of trucks, tractors and busses. To study the driving behaviour and safety of various trucks and units with different tyre combinations and loading conditions was the aim of the study. A computer-aided simulation was used for this investigation. Drive tests with a 40 t unit with prototype single tyres on the drive axle were carried out to verify the simulation. Alterations in driving behaviour and driving safety are mainly dependent on the tyre cornering stiffness. The prototype wide single tyres had a higher lateral stiffness which leads to a higher degree of under-steering (safer driving behaviour). The altered spring base on the drive axle had no influence on the side- tilt stability of vehicle combinations but the solo truck profited from the higher rear axle roll stiffness (less danger for roll-over accidents). As far as the driving safety is concerned nothing speaks against wide base tyres on the drive axle. The simulation of a tyre defect in a bend (assuming 40% of the max. transferable side force for the flat tyre) showed no increased danger using wide single tyres. Later driving tests showed however the need of tyre run flat possibilities to avoid jack-knifing of road trains. Also tyre pressure monitoring systems and electronic stability programs for the trucks are advised.
The frontal crash is still an important contributor to deaths and serious injured resulting from road accidents in Europe. As the Hybrid-III dummy used in crash tests is over two decades old, the European Enhanced Vehicle-safety Committee is studying the potential for a new test device. Key is the availability of a well-defined set of requirements that identifies the minimum level of biofidelity required for an advanced frontal dummy. In this paper, a complete set of frontal impact biofidelity requirements, consisting of references , description of test conditions and corridors, is presented.
The Swedish National Road Administration (SNRA), the Japanese Automobile Research Institute (JARI) and the Federal Highway Research Institute (BASt) are co-operating in the International Harmonized Research Activities on Intelligent Transportation Systems (IHRA-ITS). Under this umbrella a joint study was conducted. The overall objective of this study was to contribute to the definition and validation of a "battery of tools" which enables a prediction and an assessment of changes in driver workload due to the use of in-vehicle information systems (IVIS) while driving. In this sense \"validation\" means to produce empirical evidence from which it can be concluded that these methods reliably discriminate between IVIS which differ in terms of relevant features of the HMI-design. Additionally these methods should also be sensitive to the task demands imposed on the driver by the traffic situation and their interactions with HMI-design. To achieve these goals experimental validation studies (on-road and in the simulator) were performed in Sweden, Germany and Japan. As a common element these studies focused on the secondary task methodology as an approach to the study of driver workload. In a joint German-Swedish on-road study the Peripheral Detection Task (PDT) was assessed with respect to its sensitivity to the complexity of traffic situations and effects of different types of navigation systems. Results show that the PDT performance of both the German and the Swedish subjects reflects the task demands of the traffic situations better than those of the IVIS. However, alternative explanations are possible which will be examined by further analyses. Results of this study are supplemented by the Japanese study where informational demands induced by various traffic situations were analysed by using a simple arithmetic task as a secondary task. Results of this study show that relatively large task demands can be expected even from simple traffic situations.
The European Enhanced Vehicle-safety Committee (EEVC) Working Group 13 for Side Impact Protection has been developing an Interior Headform Test Procedure to complement the full-scale Side Impact Test Procedure for Europe and for the proposed IHRA test procedures. In real world accidents interior head contacts with severe head injuries still occur, which are not always observed in standard side impact tests with dummies. Thus a means is needed to encourage further progress in head protection. At the 2003 ESV-Conference EEVC Working Group 13 reported the results on Interior Headform Testing. Further research has been performed since and the test procedure has been improved. This paper gives an overview of its latest status. The paper presents new aspects which are included in the latest test procedure and the research work leading to these enhancements. One topic of improvement is the definition of the Free Motion Headform (FMH) impactor alignment procedure to provide guidelines to minimize excessive headform chin contact and to minimize potential variability. Research activities have also been carried out on the definition of reasonable approach head angles to avoid unrealistic test conditions. Further considerations have been given to the evaluation of head airbags, their potential benefits and a means of ensuring protection for occupants regardless of seating position and sitting height. The paper presents the research activities that have been made since the last ESV Conference in 2003 and the final proposal of the EEVC Headform Test Procedure.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
Topics of this report are: Securing mobility and making mobility sustainable - Strategies for road safety: Safe behavior, Safe vehicles, Safe infrastructure, Telematics, International vehicle-engineering measures " Accident statistics " Accident research " Passive vehicle safety " Active vehicle safety " Driver assistance systems " Environmental protection through vehicle engineering.
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
Powered Two Wheelers (PTWs) accidents constitute one of the road safety problems in Europe. PTWs fatalities represent 22% at EU level in 2006, having increased during last years, representing an opposite trend compared to other road users" figures. In order to reduce these figures it is necessary to investigate the accident causation mechanisms from different points of view (e.g.: human factor, vehicle characteristics, influence of the environment, type of accident). SAFERIDER project ("Advanced telematics for enhancing the SAFEty and comfort of motorcycle RIDERs", under the European Commission "7th Framework Program") has investigated PTW accident mechanisms through literature review and statistical analyses of National and In-depth accident databases; detecting and describing all the possible PTW's accident configurations where the implementation of ADAS (Advanced Driver Assistance Systems) and IVIS (In-Vehicle Information Systems) could contribute to avoid an accident or mitigate its severity. DIANA, the Spanish in-depth database developed by CIDAUT, has been analyzed for that purpose. DIANA comprises of accident investigation teams, in close cooperation with police forces, medical services, forensic surgeons, garages and scrap yards. An important innovation is the fact that before injured people arrive to hospitals, photographs and explanations about the possible accident injury mechanisms are sent to the respective hospitals (via 3G GPRS technology). By this, additional information to medical staff can be provided in order to predict in advance possible internal injuries and select the best medical treatment. This methodology is presented in this paper. On the other hand, the main results (corresponding to road, rider and PTW characteristics; pre and post-accident manoeuvres; road layout; rider behaviour; impact points; accident causations;...) from the analyses of the PTW accidents used for SAFERIDER are shown. Only accident types relevant to ADAS and IVIS devices have been considered.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
The GRSP informal group on child restraint systems (CRS) finalised phase 1 of a new regulation for the homologation of CRS . This regulation is the subject of several discussions concerning the safety benefits and the advantages and disadvantages that certain specific points may bring. However, these discussions are sometimes not based on scientific facts and do not consider the whole package but only single items. Based on the experience of the CASPER partners in the fields of human behaviour, accident analysis, test procedures and biomechanics in the area of child safety, a consideration of the safety benefits of phase 1 of the new regulation and recommendations for phase 2 will be given.