91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (164) (entfernen)
Schlagworte
- Conference (100)
- Konferenz (97)
- Germany (53)
- Deutschland (52)
- Accident (48)
- Unfall (48)
- Safety (44)
- Sicherheit (44)
- Fahrzeug (38)
- Vehicle (36)
Institut
This work aims at bringing evidence for mass incompatibility in frontal impact for cars built according to the UNECE R94 regulation. French national injury accidents database census for years 2005 to 2008 were used for the analysis. The heterogeneity of frontal self-protection among cars of different masses is investigated, as well as the partner protection parameter offered by these cars. The last part of the analysis deals with the estimation of the benefit, in terms of fatal and severe injuries avoided, if crashworthiness was harmonized for the whole fleet of vehicle. This calculation is done for France and is extended to all Europe.
Die UNECE Regelung R58 regelt die Beschaffenheit und die Installation von Heckunterfahrschutzsystemen an schweren Güterkraftfahrzeugen, deren Ziel die Verbesserung der Kompabilität zwischen Pkw-Frontstrukturen und Lkw-Hecks ist. Dennoch verunglücken laut amtlicher Unfallstatistik allein in Deutschland rund 30 Pkw-Insassen in Heckauffahrunfällen auf Lkw tödlich, da diese Vorrichtungen hinsichtlich Einbauhöhe und Steifigkeit den Anforderungen des realen Unfallgeschehens nicht genügen. Das Ziel dieser Studie ist eine quantitative Abschätzung der möglichen Reduzierung der Verletzungsschwere mit Hilfe eines statistischen Modells, die durch eine Anpassung der geltenden Bestimmungen und die damit verbundenen technischen Veränderungen des bereits vorgeschriebenen Heckunterfahrschutzes zu erreichen wäre. In einer Nutzen-Kosten-Analyse wird die Wirtschaftlichkeit dieser Modifizierungen mit einem idealen Notbremsassistenten verglichen. Die Untersuchung orientiert sich dabei an den aktuell in der UN-ECE WP29/GRSG in Genf diskutierten Vorschlägen zur Anpassung der ECE-R58. Das verwendete ordinale Probit-Modell stellt einen Zusammenhang zwischen der Verletzungsschwere im auffahrenden PKW und erklärenden Größen her, in diesem Fall der kinetischen Energie des unterfahrenden Pkws und der strukturellen lnteraktion zwischen Lkw-Heck und Pkw-Front. Diese Maßnahmen könnten demnach 53 - 78% der Getöteten sowie 27 - 49% der Schwerverletzten bei diesen Unfallkonstellationen reduzieren, was pro Jahr 20 Getöteten und 95 Schwerverletzten entsprechen würde. Somit würde eine Modifikation einer bestehenden passiven Schutzmaßnahme an jährlich 100.000 neuzugelassenen Lkw und Anhängern bereits 20 Getötete adressieren. Im Vergleich dazu müssten jährlich 3 Millionen Pkw mit zusätzlicher Sensorik und Aktuatorik für einen idealen Notbremsassistenten ausgestattet werden, um im Idealfall alle Heckauffahrunfälle von Pkw auf andere Pkw oder Lkw und damit 53 Getötete zu vermeiden. Daher fällt auch das Nutzen-Kosten-Verhältnis deutlich zugunsten des verbesserten Heckunterfahrschutzes aus.
Schutz von schwächeren Verkehrsteilnehmern: kommende Anforderungen aus Gesetzgebung und Euro NCAP
(2017)
Systeme der aktiven Fahrzeugsicherheit, insbesondere Notbremsassistenzsysteme und automatische Notbremssysteme, haben in den letzten zwei Dekaden große technische Fortschritte gemacht, und das im Wesentlichen ohne "Druck" von Gesetzgeber oder unabhängigen Testorganisationen " diese können aber durch passende Anforderungen den Vormarsch der Systeme in die Breite und die Ausnutzung von ansonsten für den Hersteller vielleicht nicht wirtschaftlichen Potentialen unterstützen. Dieser Bericht hat das Ziel, einen Überblick über die kommenden Anforderungen an Schutzsysteme für schwächere Verkehrsteilnehmer zu geben und diese Anforderungen in den Kontext Euro NCAP (=welchen Einfluss haben diese Anforderungen auf die Gesamtbewertung?) sowie Gesetzgebung (schwächere Anforderungen, aber dafür ein Markteintrittskriterium) zu stellen: - Anforderungen und Testprozeduren für Notbremsassistenz Fahrradunfälle 2018 und 2020 in Euro NCAP; - Anforderungen und Testprozeduren für Notbremsassistenz bei Nachtunfällen mit Fußgängern in Euro NCAP 2018; - Anforderungen und Testprozeduren für Abbiegeassistenzsysteme zum Schutz von Radfahrern in Unfallsituationen mit rechtsabbiegenden Lkw innerhalb der Fahrzeugtypgenehmigung.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Test and assessment procedures for passive pedestrian protection based on developments by the European Enhanced Vehicle-safety Committee (EEVC) have been introduced in world-wide regulations and consumer test programmes, with considerable harmonization between these programmes. Nevertheless, latest accident investigations reveal a stagnation of pedestrian fatality numbers on European roads running the risk of not meeting the European Union- goal of halving the number of road fatalities by the year 2020. The branch of external road user safety within the EC-funded research project SENIORS under the HORIZON 2020 framework programme focuses on investigating the benefit of modifications to pedestrian test and assessment procedures and their impactors for vulnerable road users with focus on the elderly. Injury patterns of pedestrians and cyclists derived from the German In-Depth Accident Study (GIDAS) show a trend of AIS 2+ and AIS 3+ injuries getting more relevant for the thorax region in crashes with newer cars (Wisch et al., 2017), while maintaining the relevance for head and lower extremities. Several crash databases from Europe such as GIDAS and the Swedish Traffic Accident Data Acquisition (STRADA) also show that head, thorax and lower extremities are the key affected body regions not only for the average population but in particular for the elderly. Therefore, the SENIORS project is focusing on an improvement of currently available impactors and procedures in terms of biofidelity and injury assessment ability towards a better protection of the affected body regions, incorporating previous results from FP 6 project APROSYS and subsequent studies carried out by BASt. The paper describes the overall methodology to develop revised FE impactor models. Matched human body model and impactor simulations against generic test rigs provide transfer functions that will be used for the derivation of impactor criteria from human injury risk functions for the affected body regions. In a later step, the refined impactors will be validated by simulations against actual vehicle front-ends. Prototyping and adaptation of test and assessment procedures as well as an impact assessment will conclude the work of the project at the final stage. The work will contribute to an improved protection of vulnerable road users focusing on the elderly. The use of advanced human body models to develop applicable assessment criteria for the revised impactors is intended to cope with the paucity of actual biomechanical data focusing on elderly pedestrians. In order to achieve optimized results in the future, the improved test methods need to be implemented within an integrated approach, combining active with passive safety measures. In order to address the developments in road accidents and injury patterns of vulnerable road users, established test and assessment procedures need to be continuously verified and, where needed, to be revised. The demographic change as well as changes in the vehicle fleet, leading to a variation of accident scenarios, injury frequencies and injury patterns of vulnerable road users are addressed by the work provided by the SENIORS project, introducing updated impactors for pedestrian test and assessment procedures.
The GRSP informal group on child restraint systems (CRS) finalised phase 1 of a new regulation for the homologation of CRS . This regulation is the subject of several discussions concerning the safety benefits and the advantages and disadvantages that certain specific points may bring. However, these discussions are sometimes not based on scientific facts and do not consider the whole package but only single items. Based on the experience of the CASPER partners in the fields of human behaviour, accident analysis, test procedures and biomechanics in the area of child safety, a consideration of the safety benefits of phase 1 of the new regulation and recommendations for phase 2 will be given.
Rollover scenarios in Europe
(2005)
Rollover accidents seem to be a rising problem in Europe and therefore the systematic of this accident scenario should be investigated. Based on statistical investigations on major European accident databases for different countries a series of 73 real world rollover accidents was analysed. These cases were reconstructed using PC-Crash and preliminary categorised using a modified USbased rollover classification. In a first step, the rollover events were reconstructed from the point of conflict to the vehicle- rest position. The vehicles kinematics as well as its linear and rotational velocities were derived. In a second step typical velocity characteristics as well as kinematics were identified and the events categorised according to these criteria. Based on these results four main categories were defined, covering all reconstructed accidents. This categorisation was based on mechanical parameters (rotatory and translator kinematical data of the vehicle). Significant differences can be seen for different scenarios for the "first phase of rollover".
A reduction of around 48% of all road fatalities was achieved in Europe in the past years including a reduced number of fatalities with an older age. However, among all road fatalities, the proportion of elderly is steadily increasing. In an ageing society, the European (Horizon2020) project SENIORS aims to improve the safe mobility of older road users, who have different transportation habits compared to other age groups. To increase their level of safe mobility by determining appropriate requirements for vehicle safety systems, the characteristics of current road traffic collisions involving the elderly and the injuries that they sustain need to be understood in detail. Hereby, the paper focuses on their traffic participation as pedestrian, cyclist or passenger car occupant. Following a literature review, several national and international crash databases and hospital statistics have been analysed to determine the body regions most frequently and severely injured, specific injuries sustained and types of crashes involved, always comparing older road users (65 years and more) with mid-aged road users (25-64 years). The most important crash scenarios were highlighted. The data sources included European statistics from CARE, data on national level from Germany, Sweden, Italy, United Kingdom and Spain as well as in-depth crash information from GIDAS (Germany), RAIDS (UK), CIREN and NASS-CDS (US). In addition, familiar hospital data from Germany (TraumaRegister DGU-®), Italy (Italian Register of Acute Traumas) and UK hospital statistics (TARN) were included in the study to gain further insight into specific injury patterns. Comprehensive data analyses were performed showing injury patterns of older road users in crashes. When comparing with mid-aged road users, all databases showed that the thorax body region is of particularly high importance for the older car occupant with injury severities of AIS 2 or AIS 3+, whereas the body regions lower extremities, head and thorax need to be considered for the older pedestrians and cyclists. Besides these comparisons, the most frequent and severe top 5 injuries were highlighted per road user group. Further, the most important crash configurations were identified and injury risk functions are provided per age group and road user group. Although several databases have been analysed, the picture on the road safety situation of older road users in Europe was not complete, as only Western European data was available. The linkage between crash data and hospital data could only be made on a general level as their inclusion criteria were quite different.
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.
The presentation deals with the simulation tool rateEFFECT which intends to answer the following questions: Which active safety systems should be developed to maximize safety benefit in real traffic accidents? What is the effectiveness of a specific active safety system in the real world? How many casualties could be avoided by such a system? It is shown that a lot of information is required to simulate existing accidents in order to estimate ADAS effects. This particularly includes numerical values for the pre-crash and in-crash phase. The database GIDAS provides a required minimum number of these parameters for a statistically significant sample.
Qualität von on-trip Verkehrsinformationen im Straßenverkehr : BASt-Kolloquium 23. und 24.03.2011
(2011)
Am 23. und 24. März 2011 veranstaltete die Bundesanstalt fuer Straßenwesen ein, um die Ergebnisse der erwähnten Projekte und Initiativen präsentieren zu lassen und mit anderen Experten zu diskutieren. Der vorliegende Tagungsband fasst die Ergebnisse des Kolloquiums zur "Qualität von on-trip Verkehrsinformationen" zusammen. Die Bereitstellung von Verkehrsinformationen ist geprägt von vielen Akteuren. Die Wertschöpfungskette beginnt bei der Sammlung grundlegender Verkehrsdaten zur Erstellung von Verkehrsinformationen und setzt sich mit der Datenverarbeitung und -interpretation bis hin zur Meldungserstellung fort. Die Weitergabe kann über verschiedene Übertragungsmedien erfolgen und beim Nutzer (z.B. im Navigationsgerät) empfangen werden. Jeder einzelne Schritt der Wertschoepfungskette kann sowohl von unterschiedlichen Partnern (privat oder öffentlich) übernommen werden als auch in der Hand eines Partners liegen. Diese Komplexität der Zusammenarbeit spiegelt sich demzufolge auch in Qualitätsmanagementprozessen wider. Im Rahmen des Kolloquiums wurden zwei wesentliche Qualitätsaspekte näher betrachtet: - die Datenqualität mit dem Focus auf Aktualitaet, Stimmigkeit der Daten verglichen mit einer gemessenen Realitaet sowohl zu Beginn der Wertschöpfungskette als auch an jeglichen Schnittstellen, - die Prozessqualität, welche sich insbesondere mit der reibungslosen Datenübergabe an den Schnittstellen der Wertschoepfungskette beschäftigt. Beide Qualitätsaspekte helfen zu verstehen, worin die heutigen Qualitätsprobleme bestehen und welche Massnahmen im Einzelnen ergriffen werden müssten, um eine nachhaltige Verbesserung zu erreichen. Einerseits kann es vorkommen, dass die Information über ein Verkehrsereignis an einer oder mehreren Stellen der Wertschöpfungskette korrekt vorliegt, jedoch durch ungenuegende technische oder organisatorische Schnittstellen im Prozessablauf wieder verloren geht und dem Nutzer folglich nicht zur Verfügung steht. Prominentes Beispiel eines solchen Problems in der Prozessqualität ist die fehlerhafte Interpretation der Meldung im Navigationsgerät, denkbar sind solche Informationsverluste jedoch an jeder Stelle der Wertschoepfungskette. Eine wichtige Massnahme zur Verbesserung der Prozessqualität ist die Standardisierung sowie die Überprüfung, ob die definierten Standards an jeder Stelle der Wertschöpfungskette eingehalten werden. Andererseits kann es vorkommen, dass die Datenqualität in Bezug auf ihre Genauigkeit von Anfang an so schlecht ist, dass der Nutzer eine fehlerhafte oder gar keine Nachricht übermittelt bekommt. Beispiel hierfür ist die Vielzahl von Stauereignissen, die entweder nicht gesendet wurden oder gesendet wurden, obwohl sie nicht vorhanden waren. Eine wichtige Massnahme zur Verbesserung dieser Situation ist die Verbesserung der Ereignisdetektion. Der Tagungsband enthaelt Präsentationen, die den Status Quo analysieren, Methoden zur verbesserten Datenerfassung vorschlagen und Möglichkeiten zur Verbesserung von Daten- und Prozessqualität vorstellen. Offen geblieben sind darüber hinaus folgende Fragestellungen: - Wie kann die Prozessqualität der gesamten Wertschöpfungskette bei der Vielzahl der Partner kontrolliert werden? Wer überwacht die Wertschöpfungskette? Wird hierfuer überhaupt eine zentrale Stelle benötigt? Oder ist es ausreichend, wenn jeder Partner eine angemessene Eingangs bzw. Ausgangskontrolle durchführt? - Obwohl es nur eine Realität gibt, entsteht doch Wettbewerb über die (Qualität der) Information zu dieser Realität. Wie kann Konsistenz zwischen allen Anbietern von sicherheitsrelevanten Informationen erreicht werden? Wo sollte der Wettbewerb enden und wie kann dies technisch, organisatorisch und wirtschaftlich realisiert werden? - Welche Prozesse sollten geschaffen werden, um Partner zu integrieren, die sich nicht an geschaffene Qualitätsstandards halten (z.B. kommerzielle Diensteanbieter, die nicht mit der Verkehrsinformationsszene vernetzt sind)? - Und nicht zuletzt, wie kann die Wahrnehmung des Nutzers über verschiedene Qualitätslevel unterschiedlicher Produkte verbessert werden? Ist der Nutzer in der Lage, die unterschiedlichen Qualitätsstufen von Verkehrssystemen zu unterscheiden? Falls nicht, welche Art von Unterstuetzung braucht der Kunde? Ein "European Information Services Assessment Programme" vergleichbar zu Euro NCAP für Fahrzeuge? Die Ergebnisse des Kolloquiums sollen die laufende Diskussion um die Verbesserung der Qualität von Verkehrsinformationen unterstützen.
Für eine Reihe von EU Regelungen im Bereich Fahrzeugsicherheit erlaubt eine Verordnung bereits seit dem Jahr 2010 virtuelles Testen für die Typzulassungsprüfung. Technische Details bzw. konkrete Prozeduren für spezifische Regelungen sind in dieser Verordnung jedoch nicht enthalten. Das Hauptziel des europäischen Projekts IMVITER (lmplementation of Virtual Testing in Safety Regulations) war es, basierend auf der neuen Verordnung ein virtuelles Testverfahren auszuarbeiten und dabei offene Fragen zu berücksichtigen. Um die im Projekt-Konsortium unter Berücksichtigung der Anliegen aller Interessensgruppen wie Autohersteller, Zulassungsbehörden und technischer Dienste erarbeiteten offenen Punkte zu adressieren, wurde ein generisches Flussdiagramm entwickelt, das den Ablauf einer virtuell basierten Typprüfung darstellt. ln diesem Diagramm ist der virtuelle Typgenehmigungsprozess in drei aufeinander folgende Phasen aufgeteilt, die Verifikations-, Validierungs- und Typgenehmigungsphase. Von entscheidender Bedeutung ist die Phase der Validierung des Simulationsmodells, für die im IMVITER-Projekt eine Methodik vorgeschlagen wurde. Mit der im Projekt vorgeschlagenen Validierungsmethode ist kein Austausch des Simulationsmodells zwischen Fahrzeughersteller und technischem Dienst notwendig, so dass die Vertraulichkeit von Betriebsgeheimnissen nicht gefährdet ist. Zur Validierung des Modells werden jedoch immer Versuche notwendig sein. Dies gilt sowohl für die Überpruefung von passiven als auch aktiven Fahrzeugsicherheitssystemen. Eine zusammenfassende Betrachtung der Erfahrungen aus dem IMVITER-Projekt ergab, dass mit der Einführung von virtuellem Testen keine Erhöhung der Anforderungen an die Fahrzeugsicherheit bzgl. bestehender Regelungen verbunden sein sollte. Jedoch werden auch weiterhin neue zusäztliche Regelungen erforderlich sein, da sich das Unfallgeschehen und die Fahrzeugtechnologie weiterentwickeln und ändern werden. Diese sollten von Beginn an die Möglichkeiten des virtuellen Testens nutzen, insbesondere bei Testverfahren für neue Technologien, z.B. aktiver Fahrzeugsicherheitssysteme. Hier bieten virtuelle Testverfahren nicht nur eine Kosten- oder Zeitersparnis, sondern ermöglichen teilweise erst die sinnvolle Abprüfung von neuen Sicherheitssystemen, die mit aktuellen auf Hardware-Test basierenden Verfahren überhaupt nicht möglich wären.
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
A means of assessing the passive safety of automobiles is a desirable instrument for legislative bodies, the automobile industry, and the consumer. As opposed to the dominating motor vehicle assessment criteria, such as engine power, spaciousness, aerodynamics and consumption, there are no clear and generally accepted criteria for assessing the passive safety of cars. The proposed method of assessment combines the results of experimental safety tests, carried out according to existing legally prescribed or currently discussed testing conditions, and a biomechanical validation of the loading values determined in the test. This evaluation is carried out with the aid of risk functions which are specified for individual parts of the body by correlating the results of accident analysis with those obtained by computer simulation. The degree of conformance to the respective protection criterion thus deduced is then weighted with factors which take into account the frequency of occurrence and the severity of the accident on the basis of resulting costs. Each of the test series includes at least two frontal and one lateral crash test against a deformable barrier. The computer-aided analysis and evaluation of the simulation results enables a vehicle-specific overall safety index as well as partial and individual safety values to be determined and plotted graphically. The passive safety provided by the respective vehicle under test can be defined for specific seating positions, special types of accident, or for individual endangered parts of the body.
An analysis of NASS and FARS was conducted to determine crash conditions that involved injuries that are not currently being directly addressed by vehicle safety standards or by consumer information test protocols. Analysis of both field data and US NCAP tests were conducted to determine the relative safety provided by seating position and by vehicle model year. Opportunities for improvements were determined by crash categories with large populations of injuries that were not addressed by safety tests or smaller numbers that were increasing in frequency. Areas of opportunities include improved occupant restrain in rollovers, improved frontal protection for rear seat occupants and improved fire prevention in frontal and rollover crashes.
This paper set out to examine the possibilities for injury avoidance implications for older drivers in crashes, based on crash and injury patterns among older drivers and current trends in ageing in most western societies. A number of safety technologies were identified and discussed which have potential for improving vehicle older driver crash avoidance and crashworthiness. While there were some promising estimates available of the likely benefits of this technology for improving safety, it is evident that they need to be confirmed for older drivers, given their age-related disabilities and sensory limitations. Further research is urgently required to ensure that these technologies yield safety benefits without any disbenefits for older drivers.rn
From an automotive safety occupant protection standpoint, effective occupant restraint requires a system capable of providing non-injurious occupant ride down of anticipated crash forces. This is not only the case for frontal collisions, where occupant restraint is provided primarily by seatbelts and airbags, but is also critical for other crash modes such as side impacts, rear impacts, rollovers, as well as multiple impact events. In the rear impact crash mode, occupant restraint is provided primarily by the seatbacks and to some extent the seatbelts. Foundationally, therefore, what becomes fundamental to the seatback's role in rear occupant protection is its ability to contain the occupant within the seat, preventing occupant ramping, as well as preventing the seat's, and/or its occupant's, dangerous intrusion into the rear occupant's survival space where contact with rear compartment components and/ or rear seated occupants can present a significant injury risk. An analysis is presented of a series of rear impact sled testing conducted by the authors that evaluates the timing, position and extent of the front seatback's reward displacement toward and into the rear occupant compartment as well as consideration of the front seat occupant' ramping potential and its injury potential relative to the rear compartment. Additionally, three other series of testing are presented which assess various seat designs occupant retention capabilities. Lastly, a matched-pair comparison test series is presented which evaluates occupant motion in rear impact with and without use of a typical vehicle body mounted 3-point seatbelt. Discussion of restraint system performance observed in all the testing is included along with ATD biofidelity and thigh-gap considerations. The data collected and presented includes accelerometer instrumentation and high speed video analysis.
Mit der EU-Verordnung Nummer 661/2009 zur Typgenehmigung und allgemeinen Sicherheit von Kraftfahrzeugen wird von der EU für schwere Nutzfahrzeuge der Einbau von Spurverlassenswarnsystemen und automatischen Notbremssystemen vorgeschrieben. Mit dem obligatorischen Einbau der Systeme wird eine Reduktion der Abkommens- und Auffahrunfälle von Nutzfahrzeugen aus den Klassen M2, M3, N2 und N3, die auf Grund der hohen Masse der Fahrzeuge folgenschwer sind, erwartet. Als Einführungsdaten werden der 1. November 2013 für neue Fahrzeugtypen und der 1. November 2015 für neue Fahrzeuge genannt. Leistungsanforderungen beziehungsweise technische Spezifikationen, denen die Systeme genügen müssen, liegen jedoch noch nicht vor. Diese werden derzeit von einer Expertengruppe auf UN-ECE-Ebene entwickelt. Dabei wird versucht, technologieneutrale Beschreibungen für die Ausgestaltung der Systeme zu erstellen, die gleichzeitig sowohl den gewünschten Nutzen für die Verkehrssicherheit garantieren, sich aber auch an der derzeit vorhandenen und realisierbaren Technologie orientieren. Darüber hinaus müssen die Systemkosten in einem vernünftigen Verhältnis zum Sicherheitsnutzen stehen. Ziel ist es, im Laufe des Jahres 2011 Vorschläge für die Legislative vorzulegen. Es wird über den Stand der Arbeiten, offene Fragestellungen, Herausforderungen bei der Ausgestaltung der technischen Anforderungen sowie sich abzeichnende Ergebnisse berichtet. Dabei sind die Arbeiten in Bezug auf Lane Departure Warning Systems (LDWS) bereits weiter fortgeschritten als zu Advanced Emergency Braking Systems (AEBS).
PROSPECT (Proactive Safety for Pedestrians and Cyclists) is a collaborative research project involving most of the relevant partners from the automotive industry (including important active safety vehicle manufacturers and tier-1 suppliers) as well as academia and independent test labs, funded by the European Commission in the Horizon 2020 research program. PROSPECT's primary goal is the development of novel active safety functions, to be finally demonstrated to the public in three prototype vehicles. A sound benefit assessment of the prototype vehicle's functionality requires a broad testing methodology which goes beyond what has currently been used. Since PROSPECT functions are developed to prevent accidents in intersections, a key aspect of the test methodology is the reproduction of natural driving styles on the test track with driving robots. For this task, data from a real driving study with subjects in a suburb of Munich, Germany was used. Further data from Barcelona will be available soon. The data suggests that intersection crossing can be broken down into five phases, two phases with straight deceleration / acceleration, one phase with constant radius and speed turning, and two phases where the bend is imitated or ended. In these latter phases, drivers mostly combine lateral and longitudinal accelerations and drive what is called a clothoid, a curve with curvature proportional to distance travelled, in order to change lateral acceleration smoothly rather than abrupt. The data suggests that the main parameter of the clothoid, the ratio distance travelled to curvature, is mostly constant during the intersections. This parameter together with decelerations and speeds allows the generation of synthetic robot program files for a reproduction of natural driving styles using robots, allowing a much greater reproducibility than what is possible with human test drivers. First tests show that in principle it is possible to use the driving robots for vehicle control in that manner; a challenge currently is the control performance of the robot system in terms of speed control, but it is anticipated that this problem will be solved soon. Further elements of the PROSPECT test methodology are a standard intersection marking to be implemented on the test track which allows the efficient testing of all PROSPECT test cases, standard mobile and light obstruction elements for quick reproduction of obstructions of view, and a concept for tests in realistic surroundings. First tests using the PROSPECT test methodology will be conducted over the summer 2017, and final tests of the prototype vehicles developed within PROSPECT will be conducted in early 2018
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Neue Herausforderungen an die Unfallforschung durch Fahrerassistenz und automatisiertes Fahren
(2019)
Unfallrekonstruktion hat die Ableitung von Maßnahmen zur Minimierung der Unfallfolgen ermöglicht, vor allem durch Verbesserungen bei passiven Sicherheitseinrichtungen, aber auch durch die Verbesserung der Rettungskette, beispielsweise eCall. Heute können aktive Sicherheitssysteme die Unfallfolgen bereits vor der eigentlichen Kollision reduzieren oder durch Umfeldwahrnehmung und mittels Eingriff in die Fahrzeugsteuerung gegebenenfalls sogar vollständig verhindern. Funktionen, die aktiv in die Fahrzeugsteuerung eingreifen, lassen sich nach ihrer Wirkweise unterscheiden: zum einen handelt es sich um kontinuierlich automatisierende Funktionen, die meist länger aktiv bleiben (zum Beispiel ACC). Zum anderen um Funktionen, die in kritischen Fahrsituationen temporär in die Fahrzeugsteuerung eingreifen. Aufgezeigt wird, welche Konsequenzen und Risiken in Bezug auf diese Systeme sowie für bestimmte (zum Beispiel kritikale) Fahrsituationen anzunehmen sind. Zur Bewertung von aktiven Reglern, die in kritischen Fahrsituationen eingreifen, sind Unfalldaten nur noch eingeschränkt tauglich. Ähnliches gilt für die Bewertung von Ereignissen/ Zuständen im Rahmen kontinuierlicher Fahrzeugsteuerung, vor allem, wenn diese weiter vorausliegen. Wirkzusammenhänge automatisierter Fahrfunktionen müssen jedoch - gerade für den Mischverkehr mit konventionell gesteuerten Fahrzeugen - identifiziert werden. Dafür wird eine Szenariendatenbank mit relevanten Verkehrssituationen benötigt, in die Daten aus Naturalistic Driving Studies (NDS), aus Fahrversuchen oder Versuchen im Fahrsimulator eingehen können. Die zunehmende Durchdringung der Fahrzeugflotte mit kontinuierlich automatisierten Fahrfunktionen lässt eine Abnahme kritischer Fahrsituationen und eine Reduktion der Zahl der Verkehrsopfer erwarten. Allerdings verbleibt eine Restzahl an systemimmanenten Unfällen, die als unvermeidbar gelten müssen.
Motorcycle safety research
(2007)
Honda- global motorcycle sales exceeded the 10 million units mark since 2004, and further expansion is expected. As a responsibility for a company to provide mobility, Honda is focusing on motorcycle safety as top priority and has been working on various activities for both aspects of hardware and software. Here, we present Honda- activity for the safety technology of motorcycles. At present, Honda is promoting motorcycle safety in the four themes of prevention and collision safety such as safety education, recognition assistance, accident prevention and injury reduction. First, in the area of the safety education, the "Honda Safety Driving Promotion Center" was established in 1970, and motorcycle riders and vehicle driver trainings have been organized, and the traffic training centers are used as an actual practice field not only in Japan but also in many other regions in the world. Through our training activities, the new area of safety training with hardware assistance was developed and Honda- unique technology was accumulated such as the riding simulator which can provide experience of potentially dangerous situations without risk. Especially, the "riding trainer", the popular version of the riding simulator, was introduced at several motor shows in various countries and launched in September 2005. It was distributed first in Europe and is expected to expand globally aiming at 3000 units worldwide.. And in Europe, the newest version, which includes the suburban roads program, jointly developed with ADAC, will be released in near future. In the area of recognition assistance, "vehicle to vehicle communication technology" is under development using the advantage of being a manufacturer of both motorcycles and cars. This technology is under research as Honda "ASV-3" in Japan, and as part of C2C activity in Europe. As for the accident prevention, advanced brake systems for motorcycles to assist more effective brake operation have been expanded, Honda signed the European Road Safety Charter in April 2004 with the advanced brake systems commitment and furthermore, they are expanding according to vehicle characteristics and region. Then all models above 250 cc will have a version of the system by 2010. And as the last theme, "motorcycle airbag system" is introduced which is equipped on a mass production motorcycle for the first time in the world. It has been researched and developed for a long time as an injury reduction technology for collision accidents. Honda automobile technology was used for the research and development of the motorcycle airbag, and many specific issues such as the analysis of the collision conditions particular to motorcycles have been solved to realize today- success. It might be known that ADAC in-house crash test held in August this year confirmed the high effectiveness of the airbag system and showed a positive result. This motorcycle airbag system is equipped to the Honda Gold Wing and launched in North America in August, 2006. Also in Europe, it will be sold by the end of this year. Each theme of Honda motorcycle safety technology can be seen at the Honda booth.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
The Traffic Accident Research Institute at University of Technology Dresden investigates about 1,000 accidents annually in the area around and in Dresden. These datasets have been summarized and evaluated in the GIDAS (German Accident In-Depth Study) project for 13 years. During the project it became apparent that the specific traffic situation of a covert exit of a passenger car and an intersecting two-wheeler involves a high risk potential. This critical situation develops in a large part due to the lack of visibility between the driver and the intersecting bike. In this paper the accident avoidance potential of front camera systems with lateral field of view, which allows the driver to have an indirect sight into the crossing street area will be presented.
Injury probability functions for pedestrians and bicyclists based on real-world accident data
(2017)
The paper is focusing on the modelling of injury severity probabilities, often called as Injury Risk Functions (IRF). These are mathematical functions describing the probability for a defined population and for possible explanatory factors (variables) to sustain a certain injury severity. Injury risk functions are becoming more and more important as basis for the assessment of automotive safety systems. They contribute to the understanding of injury mechanisms, (prospective) evaluation of safety systems and definition of protection criteria or are used within regulation and/or consumer ratings. In all cases, knowledge about the correlation between mechanical behavior and injury severity is needed. IRFs are often based on biomechanical data. This paper is focusing on the derivation of injury probability models from real world accident data of the GIDAS database (German In-depth Accident Study). In contrast to most academic terms there is no explicit term definition or definition of creation processes existing for injury probability models based on empirical data. Different approaches are existing for such kind of models in the field of accident research. There is a need for harmonization in terms of the used methods and data as well as the handling with the existing challenges. These are preparation of the dataset, model assumptions, censored/unknown data, evaluation of model accuracy, definition of dependent and independent variable, and others. In the presented study, several empirical, statistical and phenomenological approaches were analyzed regarding their advantages and disadvantages and also their applicability. Furthermore, the identification of appropriate prediction parameters for the injury severity of pedestrians has been considered. Due to its main effect on injuries of pedestrians and bicyclists, the importance of the secondary impact has also been analyzed. Finally, the model accuracy, evaluated by several criteria, is the rating factor that gives the quality and reliability for application of the resulting models. After the investigation and evaluation of statistical approaches one method was chosen and appropriate prediction variables were examined. Finally, all findings were summarized and injury risk functions for pedestrians in real world accidents were created. Additionally, the paper gives instructions for the interpretation and usage of such functions. The presented results include IRFs for several injury severity levels and age groups. The presented models are based on a high amount of real world accidents and describe very well the injury severity probability of pedestrians and bicyclists in frontal collisions with current vehicles. The functions can serve as basis for the evaluation of effectiveness of systems like Pedestrian-AEB or Bicycle-AEB.
This study aimed at developing an injury estimation algorithm for AACN technologies for Germany and compared them to findings based on Japanese data. The data to build and to verify the algorithm was obtained from the German in-depth Accident Database (GIDAS) and split into a training and a validation dataset. Significant input variables and the generalized linear regression model to predict severe injuries (ISS>15) were selected to maximize area under the receiver operating characteristic curve (AUC). Probit regression with the input parameter multiple impact, delta v, seatbelt use and impact direction gave the largest AUC of 0.91. Sensitivity of the algorithm was validated at 90% and specificity at 76% for an injury risk threshold of 2%. It appears that no major differences between Japan and Germany exist for injury estimation based on delta v and impact direction. However, far side impact and multiple crash events appear to be associated with a larger risk increase in the German data.
Institute for Traffic Accident Research and Data Analysis <Tokyo>rnAbstract: Analyses were conducted to clarify the features of rear-end collisions, using an integrated accident database developed by the Institute for Traffic Accident Research and Data Analysis (ITARDA). Focusing on neck injuries in rear-end collisions, analyses were made of the relation to struck-vehicle properties. Regarding the relation to the initial year of registration, the results did not show that newer vehicles tended to have a lower no-neck-injury rate, which was defined in this study as an index. On the contrary, in some passenger car classes, it was observed that the no-neck-injury rate was higher in newer vehicles. The effect of an active head restraint system, which is one type of anti-whiplash device, was analyzed by using not only the no-neck-injury rate but also a regression analysis. The results showed that the effect of an active head restraint system on suppressing the incidence of neck injuries was statistically significant.rn
The share of high-tensile steel in car bodies has increased over the last years. While occupant safety has generally benefited from this measure, there is a potential risk that, as a result, rescue time may increase considerably. In more than 60% of all car occupant fatalities a technical rescue has been necessary. These are in particular those cases where occupants die immediately at the accident scene. Therefore, in these cases "rescue time" is a very sensitive parameter. In addition to the general analysis of the need of technical rescue and the actual rescue time depending on model years, the injury pattern of occupants requiring technical rescue will be analysed to provide advice for rescue teams. Furthermore, a detailed analysis of rescue measures for the most popular car models depending on the safety cell design is given.
This work describes the results of the experimental activity, illustrating the driving behavior observed in different conditions, relating them to the different methods of ADAS intervention and comparing the driver behavior without ADAS. In the present study, driver behavior was studied in road accidents involving elderly pedestrians, with different ADAS HMIs, as a base to develop a driver model in near missing pedestrian accidents. A literature research was conducted with the aim of finding out the main influencing factors, including environment, boundary conditions, configuration of impact, pedestrian and driver information, when pedestrian fatalities occur and an analysis of frequent road accidents was conducted to get more detailed information about the driver- behavior. In order to obtain more detailed information about pedestrian accidents, real road accidents were reconstructed with multibody simulations on PC-Crash and, by the comparison between literature findings and reconstructions, a generic accident scenario was defined. The generic accident scenario was implemented on the full scale dynamic driving simulator in use at the Laboratory for Safety and Traffic Accident Analysis (LaSIS, University of Florence, Italy) in order to analyse the driving behaviors of volunteers, also considering the influence of ADAS devices. Forty-five young volunteers were enrolled for this study, resulting in forty valid tests on different testing scenarios. Two different scenarios consisted in driving with or without ADAS in the vehicle. Different kinds of ADAS, acoustic and optical, with different time of intervention were tested in order to study the different reactions of the driver. The tests showed some interesting differences between driver's behavior when approaching the critical situation. Drivers with ADAS reacted earlier, but more slowly, depending also on the type of alarm, and often with double reaction when braking. In fact, the results of the activity showed that with ADAS intervention the time to collision (TTC) increases, but the reaction time and braking modality change: a) there is a sort of "latency" time between the accelerator pedal release and the brake pressure; b) the brake pressure is initially less intense. So the driver only partially takes advance from the TTC increase. These differences were valued not only qualitatively, but quantitatively as well. This work revealed to be useful to improve the knowledge of drivers" behavior, in order to realize a driver model that can be implemented to help attaining and assessing higher levels of automation through new technology.
It has been pointed that most of the accidents on the roads are caused by driver faults, inattention and low performance. Therefore, future active safety systems are required to be aware of the driver status to be able to have preventative features. This probe study gives a system structure depending on multi-channel signal processing for three modules: Driver Identification, Route Recognition and Distraction Detection. The novelty lies in personalizing the route recognition and distraction detection systems according to particular driver with the help of driver identification system. The driver ID system also uses multiple modalities to verify the identity of the driver; therefore it can be applied to future smart cars working as car-keys. All the modules are tested using a separate data batch from the training sets using eight drivers" multi-channel driving signals, video and audio. The system was able to identify the driver with 100% accuracy using speech signals of length 30 sec or more and a frontal face image. After identifying the driver, the maneuver/ route recognition was achieved with 100% accuracy and the distraction detection had 72% accuracy in worst case. In overall, system is able to identify the driver, recognize the maneuver being performed at a particular time and able to detect driver distraction with reasonable accuracy.
This work aimed for getting the main features of accidents involving Light Goods Vehicles (LGV), using accident cases collected in the In-Depth Accidents Studies built up at IFSTTAR-LMA (France), in order to analyse thoroughly the proceedings of these accidents and identify the major factors for the different types of LGV. This work was based on the analysis of 88 accident cases involving LGV with a Maximum Authorised Mass inferior to 3.5 tonnes. In particular kinematics reconstruction of these accidents were performed to calculate the average impact speeds and to better understand the compatibility problems between LGV and antagonist vehicles. Specific features have been reviewed to pick up problems concerning safety, maintenance, loading, LGV design: general conditions of the accident, vehicle features, and passive safety. The main results of this study are presented in this paper.
Bus or heavy vehicle passenger accidents are rare events, compared with car accidents, but sometimes leads to a large number of victims especially in rollover crash scenarios. Two accidents occurred in Portugal in 2007 and 2013 in which 28 people died and more than 50 are injured, shown the importance of the investigation of such accidents. For the investigation of these accidents multidisciplinary teams are constituted with engineers and police officers. All the factors involved are taken into consideration including road design, traffic signs, maintenance and hardware, human factors, and vehicle factors. In this work a methodology to an accurate collection of the data is proposed. From the information collected the accident is reconstructed using the PC-CrashTM software. From this all the contribution factors are determined and recommendations to mitigate these crashes are listed. These two accidents are rollover accidents and the analysis of the injuries and its correlation with the use of retention systems is very important. From the medical data and with the dynamics of the accident determined simulations of the occupants with biomechanical models are carried out in order to evaluate the effect of the retention systems in the injuries. This analysis is based on injury criteria (such as Abbreviated Injury Score (AIS) or Injury Severity Scale (ISS)). With this it is possible to determine if the seat belt was worn or not.
In-depth road traffic accident research in Spain is a fairly recent activity. In the past, only accident data that had been retrospectively processed by the national and regional traffic police forces was available. In 1999 Applus+IDIADA set up a permanent accident research unit to carry out indepth analysis of road accidents in Spain. Since then accidents involving cars, motorcycles, coaches and vulnerable road users have been thoroughly studied. The Applus+IDIADA accident research team has carried out work for the various traffic polices in Spain and it is currently involved in several research projects in which accidentology is one of the main tasks. The working methodology of the team is presented in the first part of the paper. In the framework of the European research project "Rollover" (GRD2-2001-50086), Applus+IDIADA has collected data, inspected scenarios and performed virtual reconstructions of twenty-six of the total seventy-six rollover accidents studied. The second half of the paper describes how these accident investigations were used to develop a test procedure for identifying possible improvements to the vehicle structure which augment occupant protection in a rollover scenario. In particular, a proposal for a new drop test for rollover assessment is presented. The cases were analysed for severity, in terms of injury to the occupants and damage to the vehicle, and taking into account whether a seatbelt was worn or not. The worst possible cases were identified as those that had severe occupant injuries and sizable damage to the occupant compartment when seatbelts had been worn. The most severe cases were then analysed further for impact position (roll and pitch angles) and the impact velocity. With these parameters taken into account, the most representative combinations could be found. This resulted in a series of configurations for possible drop tests. The results of the tests indicate where passenger vehicle structures need to be improved in order to increase occupant safety in the event of a rollover crash.
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
The objective of this study was to identify aspects of the individual experience and behaviour of drivers in intersection accidents. A total of 40 accident drivers sketched their ideas and expectations relating to intersection assistance using the method of Structure Formation Technique. Using this method prepared content cards and relation cards for a subject matter are formed together in a structure through the application of an explicit set of rules. The structures generated in this process were compared with the structures of 20 control persons who have not recently experienced an accident at intersections. The basis for this comparison was a case-control design with matched samples regarding the variables age, sex, education, occupation, driving experience and annual mileage. The results of the accident reports indicate that additional assistance is instrumental in the perception of other road users. Generally the interviewed drivers were open-minded towards the use of intersection assistance systems. Drivers who have recently experienced an accident at intersections significantly more often approved of warning assistance in their vehicle than drivers who have not recently experienced an accident. Further accident experienced drivers favoured warning and information via audio warning more frequently. The ideas of the drivers were strongly shaped by the experiences with already available advanced driver assistance systems. Hence acoustic and visual warnings were generally preferred to tactile warnings. The findings also indicate a relationship between the variable age and the acceptance of automatic vehicle intervention, and the suggestion of a head up display as a configuration of a visual warning system.
The market introduction and penetration of electric vehicles can be seen as a milestone in order to reduce the environmental burden imposed by the transport sector. The wide-spread use of electric vehicles powered by electricity from renewable sources promises a substantial reduction of local emissions in urban areas as well as greenhouse gas emissions. To be a successful mobility alternative several obstacles and challenges have to be overcome first. Especially the customers' purchase decision determines finally whether an innovation like electromobility will be successful. Therefore, this paper concentrates on demand-related obstacles and barriers for a broad market deployment of electric cars. Within the Electromobility+ project eMAP these issues are investigated via a consumer survey. It was designed to identify the awareness of potential consumers of electric cars as well as give an estimate of the attitude towards this new technology. In addition to the picture of potential demand-related obstacles the consumers were asked to evaluate the suitability of various promotion measures.
The misuse of CRS (child restraint system) is one of the most urgent problems in connection of child safety in cars. Numerous field studies show that more than two thirds of all CRS are used in a wrong way. This misuse could lead to serious injuries for the children. Surprisingly the quality of CRS use is coded much better in accident data (e.g. GIDAS) than the results of observatory field studies show. It is expected that misuse of CRS was not detected by the accident teams in a large number of the cases. An essential part in improving child seats and their usability is the knowledge of the relation between misuse and resulting injuries. For that the analysis and experimental reconstruction of accidents is an important part. For allowing an exact experimental accident reconstruction, it is necessary to have detailed information about the securing situation of the child and about the installation of the CRS in the car.
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of synthetic and plastic materials as a material for the interior equipment of buses and coaches because of their ood mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years - also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, the production of smoke, the smoke development and propagation and its toxicity for the people as well as the testing methods and limit values are of interest. For those reasons research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behavior of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and on-board extinguishing equipment were elaborated. At the other hand research is carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. The paper describes which effective and economically reasonable fire safety requirements for interiors of buses would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Today's volumes of traffic require more and more responsibility from each individual road user in their interactions. Those who drive motor vehicles have the singular obligation to minimise the risk of accidents and hence the severity of injuries, particularly with a view to the most vulnerable road users such as motor bikes, bikes and pedestrians. Since responsible and pro-active driving depends first and foremost on the visual information relayed by our eyes and the visual channel this requires good command of the traffic and all-round visibility from our driver's seat. Granted that human error can never be fully excluded, improving visibility around the car is nevertheless an urgent priority. To do so, we need to rate visibility in the most realistic driving situations. Since the existing visibility metrics and methodology are not applicable to real-life driving situations, this study aimed at developing a new visibility rating methodology based on real-life accident scenarios. On the basis of the cases documented by the accident research project, this study analysed criteria indicative of diminishing visibility on the one hand and revealing some peculiarities in connection with the visibility issue on the other. Based on the above, the project set out to develop a rating methodology allowing to assess all-round visibility in various road situations taking into account both driver and road geometries. In this context, the assessment of visibility while turning a corner, crossing an intersection and joining traffic on a major road (priority through route) is of major importance. The first tests have shown that critical situations can be avoided by adapting the relevant geometries and technical solutions and that significant improvements of road safety can be derived therefrom.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.