Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (637) (entfernen)
Schlagworte
- Conference (386)
- Konferenz (382)
- Germany (212)
- Deutschland (209)
- Unfall (188)
- Accident (187)
- Safety (123)
- Sicherheit (122)
- Injury (117)
- Verletzung (117)
Institut
When the EEVC proposed the full-scale side impact test procedure, it recommended that consideration should be given to an interior headform test in addition. This was to evaluate areas of contact not assessed by the dummy. EEVC Working Group 13 has been researching the parameters of a possible European headform test procedure in four phases. Earlier stages of the research have been presented at previous ESV conferences. The conclusions from these have suggested that the US free motion headform should be used in any European test procedure and that it should be a free flight test, not guided. This research has now culminated in proposals for a European test procedure. This paper presents the proposed EEVC side impact interior headform test procedure, giving the rationale for the test and the first results from the validation phase of the test protocol.
The development of tyre- and truck-manufacturers leads to the direction to introduce wide base single tyres (size 495/45R22,5) instead of twin tyres on the driving axle of trucks, tractors and busses. To study the driving behaviour and safety of various trucks and units with different tyre combinations and loading conditions was the aim of the study. A computer-aided simulation was used for this investigation. Drive tests with a 40 t unit with prototype single tyres on the drive axle were carried out to verify the simulation. Alterations in driving behaviour and driving safety are mainly dependent on the tyre cornering stiffness. The prototype wide single tyres had a higher lateral stiffness which leads to a higher degree of under-steering (safer driving behaviour). The altered spring base on the drive axle had no influence on the side- tilt stability of vehicle combinations but the solo truck profited from the higher rear axle roll stiffness (less danger for roll-over accidents). As far as the driving safety is concerned nothing speaks against wide base tyres on the drive axle. The simulation of a tyre defect in a bend (assuming 40% of the max. transferable side force for the flat tyre) showed no increased danger using wide single tyres. Later driving tests showed however the need of tyre run flat possibilities to avoid jack-knifing of road trains. Also tyre pressure monitoring systems and electronic stability programs for the trucks are advised.
The frontal crash is still an important contributor to deaths and serious injured resulting from road accidents in Europe. As the Hybrid-III dummy used in crash tests is over two decades old, the European Enhanced Vehicle-safety Committee is studying the potential for a new test device. Key is the availability of a well-defined set of requirements that identifies the minimum level of biofidelity required for an advanced frontal dummy. In this paper, a complete set of frontal impact biofidelity requirements, consisting of references , description of test conditions and corridors, is presented.
The Swedish National Road Administration (SNRA), the Japanese Automobile Research Institute (JARI) and the Federal Highway Research Institute (BASt) are co-operating in the International Harmonized Research Activities on Intelligent Transportation Systems (IHRA-ITS). Under this umbrella a joint study was conducted. The overall objective of this study was to contribute to the definition and validation of a "battery of tools" which enables a prediction and an assessment of changes in driver workload due to the use of in-vehicle information systems (IVIS) while driving. In this sense \"validation\" means to produce empirical evidence from which it can be concluded that these methods reliably discriminate between IVIS which differ in terms of relevant features of the HMI-design. Additionally these methods should also be sensitive to the task demands imposed on the driver by the traffic situation and their interactions with HMI-design. To achieve these goals experimental validation studies (on-road and in the simulator) were performed in Sweden, Germany and Japan. As a common element these studies focused on the secondary task methodology as an approach to the study of driver workload. In a joint German-Swedish on-road study the Peripheral Detection Task (PDT) was assessed with respect to its sensitivity to the complexity of traffic situations and effects of different types of navigation systems. Results show that the PDT performance of both the German and the Swedish subjects reflects the task demands of the traffic situations better than those of the IVIS. However, alternative explanations are possible which will be examined by further analyses. Results of this study are supplemented by the Japanese study where informational demands induced by various traffic situations were analysed by using a simple arithmetic task as a secondary task. Results of this study show that relatively large task demands can be expected even from simple traffic situations.
The European Enhanced Vehicle-safety Committee (EEVC) Working Group 13 for Side Impact Protection has been developing an Interior Headform Test Procedure to complement the full-scale Side Impact Test Procedure for Europe and for the proposed IHRA test procedures. In real world accidents interior head contacts with severe head injuries still occur, which are not always observed in standard side impact tests with dummies. Thus a means is needed to encourage further progress in head protection. At the 2003 ESV-Conference EEVC Working Group 13 reported the results on Interior Headform Testing. Further research has been performed since and the test procedure has been improved. This paper gives an overview of its latest status. The paper presents new aspects which are included in the latest test procedure and the research work leading to these enhancements. One topic of improvement is the definition of the Free Motion Headform (FMH) impactor alignment procedure to provide guidelines to minimize excessive headform chin contact and to minimize potential variability. Research activities have also been carried out on the definition of reasonable approach head angles to avoid unrealistic test conditions. Further considerations have been given to the evaluation of head airbags, their potential benefits and a means of ensuring protection for occupants regardless of seating position and sitting height. The paper presents the research activities that have been made since the last ESV Conference in 2003 and the final proposal of the EEVC Headform Test Procedure.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
Topics of this report are: Securing mobility and making mobility sustainable - Strategies for road safety: Safe behavior, Safe vehicles, Safe infrastructure, Telematics, International vehicle-engineering measures " Accident statistics " Accident research " Passive vehicle safety " Active vehicle safety " Driver assistance systems " Environmental protection through vehicle engineering.
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
Powered Two Wheelers (PTWs) accidents constitute one of the road safety problems in Europe. PTWs fatalities represent 22% at EU level in 2006, having increased during last years, representing an opposite trend compared to other road users" figures. In order to reduce these figures it is necessary to investigate the accident causation mechanisms from different points of view (e.g.: human factor, vehicle characteristics, influence of the environment, type of accident). SAFERIDER project ("Advanced telematics for enhancing the SAFEty and comfort of motorcycle RIDERs", under the European Commission "7th Framework Program") has investigated PTW accident mechanisms through literature review and statistical analyses of National and In-depth accident databases; detecting and describing all the possible PTW's accident configurations where the implementation of ADAS (Advanced Driver Assistance Systems) and IVIS (In-Vehicle Information Systems) could contribute to avoid an accident or mitigate its severity. DIANA, the Spanish in-depth database developed by CIDAUT, has been analyzed for that purpose. DIANA comprises of accident investigation teams, in close cooperation with police forces, medical services, forensic surgeons, garages and scrap yards. An important innovation is the fact that before injured people arrive to hospitals, photographs and explanations about the possible accident injury mechanisms are sent to the respective hospitals (via 3G GPRS technology). By this, additional information to medical staff can be provided in order to predict in advance possible internal injuries and select the best medical treatment. This methodology is presented in this paper. On the other hand, the main results (corresponding to road, rider and PTW characteristics; pre and post-accident manoeuvres; road layout; rider behaviour; impact points; accident causations;...) from the analyses of the PTW accidents used for SAFERIDER are shown. Only accident types relevant to ADAS and IVIS devices have been considered.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
The GRSP informal group on child restraint systems (CRS) finalised phase 1 of a new regulation for the homologation of CRS . This regulation is the subject of several discussions concerning the safety benefits and the advantages and disadvantages that certain specific points may bring. However, these discussions are sometimes not based on scientific facts and do not consider the whole package but only single items. Based on the experience of the CASPER partners in the fields of human behaviour, accident analysis, test procedures and biomechanics in the area of child safety, a consideration of the safety benefits of phase 1 of the new regulation and recommendations for phase 2 will be given.
The objective was to develop and validate a crash trolley (reference vehicle) equipped with a compartment and a full restraint system for driver and front seat passenger which can be used in full scale crash testing. Furthermore, the crash trolley should have a suspension to show rotation and nick effects similar to real vehicles. Within the development phase the reference vehicle was build based on a European family car. Special attention was needed to provide appropriate strength to the trolley and its suspension. The reference vehicle is equipped with a restraint system consisting of airbags, pedals, seats, dashboard, and windscreen. On the front of the vehicle different crash barriers can be installed to provide miscellaneous deceleration pulses. For the validation phase a series of low and high speed crash tests with HIII dummies were conducted and compared with full scale tests. For the comparison deceleration pulse, dummy numbers and vehicle movement were analyzed. Validation tests with velocities up to 60 km/h showed promising results. The compartment and the suspension systems stayed stable. Rotation effects were comparable with full scale car crash tests. The airbags and seat belt system worked reasonable. The acceleration pulse compared to an Euro NCAP test had a similar characteristic but was in general slightly lower. After the successful validation the reference vehicle is already in use in different studies in the field of vehicle safety research at BASt.
Topics of the status report are: Road accidents in Germany " Socio-economic costs due to road traffic accidents in Germany " Vehicle population and road performance " Electromobility " Alternative power train technologies: market penetration and consequences. The following research subjects are presented: Safety of electric vehicles " Driving dynamics of electric propelled vehicles " New requirements for the periodic technical inspection of electric and hybrid vehicles " Forward looking safety systems " Periodic roadworthiness tests " Cooperative systems: integration of existing systems " Safety related traffic information " Urban space: User oriented assistance systems and network management " Automated driving " Study on camera-monitor-systems " Freight transport " BioRID TEG, dummy harmonization " Frontal impact and compatibility " Child safety " FlexPLI " GIDAS: a blueprint for worldwide in-depth road accident investigations " Druid: Driving under the influence of drugs, alcohol and medicines " Smoke and toxicity in bus fires.
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of synthetic and plastic materials as a material for the interior equipment of buses and coaches because of their ood mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years - also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, the production of smoke, the smoke development and propagation and its toxicity for the people as well as the testing methods and limit values are of interest. For those reasons research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behavior of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and on-board extinguishing equipment were elaborated. At the other hand research is carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. The paper describes which effective and economically reasonable fire safety requirements for interiors of buses would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses.
Since integrated safety systems combine active and passive safety elements in one safety system, it is necessary to define new procedures to evaluate vehicle safety from the overall system point of view. The main goal of the ASSESS project is to develop harmonized and standardized assessment procedures for collision mitigation and avoidance systems. Methods and Data Sources: In ASSESS, procedures are developed for: driver behaviour evaluation, pre-crash system performance evaluation, crash performance evaluation, socio-economic assessment. This paper will concentrate on the activities related to the crash evaluation. The objective is to perform simulations, sled tests and crash tests in order tounderstand the influence of the activation of the pre-crash systems on the occupants" injuries during the crash phase. When a traffic accident is unavoidable, pre-crash systems work on various safety devices in order to improve the vehicle occupants" protection. Braking assistance and adaptive restraint systems are the main pre-crash systems whose effect on the occupants" protection will be described in this paper. Results: The results will be a description of the effect of the activation of the pre-crash systems on the crash phase. Additionally, a set of recommendations for future methodology developments will be delivered. Furthermore, a first approach to the study of the effect of the pre-crash systems activation on the occupants" protection when the impact is unavoidable will be presented. This effect will be quantified using the biomechanical values obtained from the simulation and testing activities and their related injury risks. Simulation and testing activities will consider the following scenarios: - No activation of any pre-crash system, - Activation of one or a combination of several pre-crash systems. In this way, differences in the results obtained from different scenarios will show the effect of each pre-crash system separately during the crash phase. Discussion and Limitations: The set of activities developed in this research project is limited by the fact that with the given resources only a limited number of vehicle models could be investigated. In addition, there are also limitations related to the injury risk curves and the passive safety tools currently on the market. Conclusion and Relevance to session submitted: The paper will present a complete analysis of the effect of pre-crash systems during the crash phase when the impact is unavoidable. Details, limitations and first application experience based on a few examples will be discussed. Currently, there is not any regulation, assessment program, or other similar official procedure able to assess pre-crash systems during the crash phase. This project comprises phases of traffic accidents which have been historically analysed separately, and aims to evaluate them taking into account their interrelationship. ASSESS is one of the first European projects which deals in depth with the concept of integrated safety, defining methodologies to analyse vehicle safety from a global point of view.
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
Thoracic injuries are one of the main causes of fatally and severely injured casualties in car crashes. Advances in restraint system technology and airbags may be needed to address this problem; however, the crash test dummies available today for studying these injuries have limitations that prevent them from being able to demonstrate the benefits of such innovations. THORAX-FP7 was a collaborative medium scale project under the European Seventh Framework. It focused on the mitigation and prevention of thoracic injuries through an improved understanding of the thoracic injury mechanisms and the implementation of this understanding in an updated design for the thorax-shoulder complex of the THOR dummy. The updated dummy should enable the design and evaluation of advanced restraint systems for a wide variety (gender, age and size) of car occupants. The hardware development involved five steps: 1) Identification of the dominant thoracic injury types from field data, 2) Specification of biomechanical requirements, 3) Identification of injury parameters and necessary instrumentation, 4) Dummy hardware development and 5) Evaluation of the demonstrator dummy. The activities resulted in the definition of new biofidelity and instrumentation requirements for an updated thorax-shoulder complex. Prototype versions were realised and implemented in three THOR dummies for biomechanical evaluation testing. This paper documents the hardware developments and biomechanical evaluation testing carried out.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Topics of this report are: Road accidents in Germany - Socio-economic costs due to road traffic accidents - Vehicle population and road performance " Automotive IT " Electromobility. The following research subjects are presented: Safety of electric vehicles - Forward looking safety systems - Cooperative systems - Safety related traffic information - Freight transport: Action plan freight transport and trial with longer trucks - Lane departure warning systems and Advanced emergency braking systems (AEBS) for heavy duty vehicles - Dummy harmonization " Compatibility - Child safety - Virtual testing - Driving under the influence of drugs, alcohol and medicines - Fire safety of buses - Milled shoulder rumble strips - Conspicuity of powered-two-wheelers - Automatically dipped high beam and rear view mirrors.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Technical progress in automotive engineering focuses at the moment on two competing branches: improving safety and reducing energy consumption. Recent consideration has been given to a third factor, cost to the consumer. Challenges are presented by demographic changes, especially with increasing participation of elderly people in road traffic. The report considers the recent history of road accidents in Germany and statistics relating to vehicle population and road performance. There is a general trend towards decreasing numbers of accidents and their severity. Transport is responsible for roughly 20% of CO2 emissions and approximately 70% of total petroleum consumption. The Federal Government has responded to these challenges by publishing the Freight Transport and Logistics Masterplan in the summer of 2008. It describes the strategic transport policy direction and the key elements of the future course of action which are to be used to ensure the provision of efficient infrastructure and, at the same time, to reduce the amount of energy consumed by vehicles and make transport more efficient, cleaner and quieter. This document contains a number of concrete measures subsumed under the following six objectives: Making optimum use of transport infrastructure - shaping transport to make it more efficient; Reducing the number of journeys - ensuring mobility; Transferring more traffic to the railways and inland waterways; Upgrading more transport arteries and hubs; Environmentally friendly, climate friendly, quiet and safe transport, and Good working conditions and good training in the freight transport industry. Progress in research is outlined in the following areas: Daytime Running Lights for Motorcycles; Safety of hydrogen vehicles - addressing safety and environmental issues by development of a Global Technical Regulation for hydrogen vehicles; Elements of active vehicle safety for elderly drivers; Periodical Technical Inspection of electronically controlled systems in road vehicles - Electronic Stability Control; Pedestrian protection; Crash Compatibility - role of collision partner in passive safety tests; Child safety; Euro NCAP - Child Restraint Systems, and German Field Operational Test on Car-to-Car and Car-to-Infrastructure Systems (SIM-TD). The research project AKTIV - "Adaptive and Cooperative Technologies for Intelligent Traffic" encompasses the design, development, and evaluation of novel driver assistance systems, knowledge and information technologies and is set up to find solutions for efficient traffic management and Car-to-Car and Car-to-Infrastructure communication for future cooperative vehicle applications. The European Statement of Principles on the Human Machine Interface (HMI), presented at the eSafety Conference, which was held in Berlin on 5/6 June 2007, addresses issues such as Real Time Traffic Information (RTTI), Legal issues of Advanced Driver Assistance Systems (ADAS) and e-security.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
There is a need to continue to set the right vehicle safety policy priorities in the future. Research has to point out the most cost efficient and safety relevant measures to further reduce the number of road traffic casualties. The overall development shows that the constant and rapid decrease in the number of road casualties slows down. New innovations need to enter the vehicle market soon, in order to continue the success achieved in the last decade. Priorities for vehicle safety are driven by safety and mobility demands. It is necessary to keep a strong lid on all aspects of elderly and vulnerable road users. The fraction of powered-two-wheelers (PTW) is a priority group. PTWs have a risk of being involved in an accident, 14times higher than that of a passenger car. However, the figures do also show that every second fatality is a car occupant. Therefore passenger car safety remains to be top priority. Heavy goods vehicles are overly represented in fatal accidents, addressing the need to make these vehicles more compatible with other road users. These facts highlight the necessity not only to increase vehicles" self protection, but also to make cars - and trucks - more compatible and safe. Cycling is a strongly increasing mode of transport. This is a further reason to demand better protection for cyclists and pedestrians from car design and car active and integrated safety systems. Another priority for future vehicle safety is related to demographics. It is less known that the purely demographic effect will be superimposed by an increasing wish of elderly people to be mobile. However, elderly people show deficits concerning their biomechanics. This emphasizes the need for better and more adaptive restraint systems, but also further technological challenges and demands for active safety systems. However, in order to progress, current technological limitations have to be overcome. Cost benefit considerations, but also consumer acceptance and desires, will drive this process.
Accident research 2.0: New methods for representative evaluation of integral safety in traffic
(2013)
BMW has developed a procedure for rating Advanced Driver Assistance Systems (ADAS) benefits that integrates two distinct tools. The tool "S.A.F.E.R." is designed to analyze the pre-crash phase. The aim of S.A.F.E.R. is to simulate all relevant processes in sufficient detail to obtain reproducible estimates of key indicators (effectiveness, false positives, etc.). The relevant processes include not only traffic and vehicle dynamics, but also environmental and most importantly human factors. Representative distributions of factors and parameters are obtained by taking the stochastic variation of all relevant parameters into account in the simulations. The second tool, known as "ICOS", has been designed to provide a high-resolution, high-fidelity description of crash phase dynamics. If one converts the outputs of stochastic simulation into inputs for crash dynamics, the result is a comprehensive description of exactly how a safety system can reduce injuries. Applications currently focus on high-fidelity simulation of individual crashes in order to enhance our understanding and optimization of connected safety systems. An integrated simulation process thus allows an exact prediction of the effectiveness in individual cases in terms of injury severity. The development and rating of integral safety need to reflect the true efficiency in the field. The integrated approach described here could provide a valid and reproducible basis for rating connected systems of active and passive safety. In particular, "virtual experiments" using a traffic-based approach and incorporating models of all relevant processes constitute an essential element of the approach.
The presentation deals with the simulation tool rateEFFECT which intends to answer the following questions: Which active safety systems should be developed to maximize safety benefit in real traffic accidents? What is the effectiveness of a specific active safety system in the real world? How many casualties could be avoided by such a system? It is shown that a lot of information is required to simulate existing accidents in order to estimate ADAS effects. This particularly includes numerical values for the pre-crash and in-crash phase. The database GIDAS provides a required minimum number of these parameters for a statistically significant sample.
Introduction: The incidence of trauma-related cervical-spine fractures is 19-88 / 100.000. In contrast, the incidence of cervical spine injuries is as high as 19% - 51% of all spinal trauma. Cervical spine injuries in non-polytrauma patients are rare. However, due to the potential damage to the spinal cord these traumata are feared and mustn't be missed. Cervical spine injuries represent the highest reported early mortality rate of all spinal trauma. The rate of functional impairment afterwards is high and the rate of reintegration into work is low compared to other organ systems. In the past, trauma surgeons often did x-rays of the cervical spine with low inhibition threshold and often without strong clinical suggestion for vertebral or discoligamental injuries. This practice was queried by the Canadian C-Spine rule and extensively discussed in the past. Therefore we did a retrospective study whether non-polytrauma patients benefit from cervical spine x-rays.
This paper will outline ETSC's contribution to the European Union's road safety policy 2011-2020. It will present some of the main recommendations from ETSC's Blueprint for the 4th Road Safety Action Programme and will introduce the response to the European Commission's Road Safety Policy Orientations 2011-2020 (published July 2010). The second framework document presented is the Transport White Paper (published March 2011). The paper will focus on new targets and the new vision set for Europe's Road Safety policy picking out some issues in particular such as traffic law enforcement and the protection of vulnerable road users. It will argue that by reinforcing the current Road Safety Policy Orientations, the EU will be better placed to reach its new ambitious goal of halving road deaths by 2020 and the longer term zero casualty vision.
Analysis of the accident scenario of powered two-wheelers on the basis of real-world accidents
(2013)
For the first time since 20 years the German national statistics of traffic accidents revealed an increasing number of fatalities and seriously injured persons in 2011. This negative development was especially caused by increasing numbers in all groups of vulnerable road users (VRU). Furthermore, the comparison of fatality reduction rates between several categories of road users shows that persons on motorcycles show the worst performance over years. Although every second fatality in German traffic accidents is still a car occupant, users of PTW make up more than 20% in the meantime. Assuming further improvements in the field of occupant protection this trend will continue. For that reason, a study on the basis of real-world accidents was conducted to describe the accident scenario involving motorcycles and to identify the reasons of the above-described fact. Approximately 1.800 motorcycle accidents out of GIDAS database were used for the analyses. The first part of the study deals with the question how representative the GIDAS database is for the German motorcycle accident scenario. Afterwards, detailed descriptive statistics on motorcycle accidents were presented considering numerous parameters about the accident scene, environmental influences, vehicle information, individual characteristics, interview data, injury severity and injury causation. One important point is the identification of the most frequent critical situations that are typical for motorcycle accidents. Furthermore, a special focus was on accident causation. Finally, conspicuous facts out of the analysis are emphasized. All in all, the study gives a comprehensive overview about the German motorcycle accident scenario. One the one hand, the use of weighted GIDAS data allows representative and robust statements on the basis of large case numbers; on the other hand highly detailed conclusions can be drawn. The results of the study help to understand the particularities of motorcycle accidents and provide approaches for further improvements in the field of PTW safety.
It is very important for Automotive OEMs to get feedback on their product performance on real roads for continuous improvement. Every OEM has a way of collecting this feedback for various performance parameters. Systematic accident research is a way to generate the information related to safety performance of the vehicle. In India, while there is a large amount of data related to the accidents, it is found this data is aimed at understanding the gross statistics and not directly useful for technology development. This paper explains learnings from a pilot study carried out in collaboration with an Emergency Medical Services provider on one of the expressways (motorways). This pilot study has resulted in development of working model that could now be scaled up at for wider application. The paper also presents some of the important observations based on the data collected.
Police records about traffic accidents like used by IRTAD (International Road Traffic and Accident Database) and CARE (Community Road Accident Database) do not represent all road injuries. For instance, road accidents of bicyclists without a counterpart are usually not reported. Furthermore, IRTAD-like data contains hardly any information on injury outcome and accident circumstances. This information gap leads to an under-representation of the safety concerns of the most vulnerable road users like children and the elderly both in accident research and safety promotion. Injury registration for the European Injury Database (IDB), in turn, combines details of accident causation with diagnostic information that can be used to assess injury severity and long term consequences. The IDB is collecting data from hospital emergency department patients and is being implemented in a growing number of countries. In this article IDB results on mode of transport and injury outcome are presented from a sample of nine EU member states.
While accident statistics on a national level are provided by many countries, there is a need for international data that includes more detailed information about the accident, so called in-depth data. As a consequence, accident data projects have been emerging in different regions of the world. This creates a need for comparable and mergeable data from different countries, enabling the use of already existing accident data resources and helping to expedite the improvement of global road safety. While existing approaches focus that mostly on building a comprehensive accident database from scratch, the iGLAD project (Initiative for the Global Harmonization of Accident Data) attempts a more pragmatic approach by building on top of the work already accomplished in this area and complementing it. The target of iGLAD is to help setting up an additional dataset as a compatibility layer between already existing world wide data sets and integrating the structure of these by defining a common data scheme. This dataset is limited to the common denominator between the existing data sets and is inherently rather small and simple. Eventually, an individual converter for each participating accident investigation group will be built that enables pooling all data sets in a common repository. This not only saves costs and time, and hence makes such a target more feasible, but also creates data that is usable right from the start. This paper gives an overview of the current status of iGLAD and first steps taken. Additionally, some methodological aspects are discussed, next to a glance at other projects working currently on related issues, providing additional input for iGLAD. Finally, an overview of next steps and intended future work is given.
The increasing economics in India has an enormous growth of its road traffic. As observed from official Indian accident statistics the number of road fatalities are one of the highest worldwide. In contrast to most industrialized nations they have an rapidly increasing trend. To come along with this trend it becomes more than essential to understand the traffic accident situation. The official Indian accident statistics gives a glimpse of only basic information. Therefore more detailed data is needed. By using In-depth accident data and officially representative statistics the current accident situation can be evaluated in India, if a suitable weighting methodology is considered. Hence in 2009/2010 a pilot study with the collaboration partner JP-Research India pvt. Ldt. was gathered in Tamil Nadu in south of India. In-depth accident investigations were done around the Coimbatore area on four highways. At first, the collected data is evaluated. Due to consequent and continuous further development based on the first approach a methodology similar to NASS/CDS/GES in the US and GIDAS in Germany was developed. Of course all relevant accident related parameters including pictures and severity information were collected. As a matter of fact based on scaled sketches and reconstruction benefit analyses can be done in order to analyze the accident scenery in India. As a first outcome influence from infrastructure, missing education and vehicle safety were identified as key parameters in order to reduce the number of accidents and casualties. To compare the accident situation against international standards an accident classification for left hand traffic was developed based on the German Insurance classification system. Looking into detail additional accident types were identified and added to create an Indian accident type catalogue. The positive results encouraged several OEMs to participate in this investigation and together with BOSCH a consortium was established in 2010/11. Within one year from beginning in May 2011 about 200 highway accidents were collected, reported and reconstructed using the new standard. Hence a first good overview of the accident situation is available for the Coimbatore Tamil Nadu area. The major target for establishing accident investigations is the extension towards other states of India and urban areas to achieve a better overview of the accident scenery. Therefore local and national authorities have to be embedded in order to strengthen the awareness against traffic safety.
Do learner gain sufficient braking capabilities at the end of education for collision avoidance?
(2013)
The paper describes a test design to evaluate the braking behaviour in the course of the driver education. The results show that the braking capabilities increased during the driver education and the learning effects are the same for males and females. The evaluation limit is set to 6 m/s-². At the beginning of education, 50% of the drivers do not reach this limit, although the driver education car is equipped with an emergency brake assist, which is regularly installed in all vehicles since 2009. After the education, 100% of the drivers can reach the limit. The results are mapped to a collision avoidance scenario.
Since 2008, the authors inspected fatal traffic accidents on the spot every year, with the cooperation of Toyota police station in Aichi pref. In the jurisdiction, numbers of fatal accidents were 18 in 2008, 12 in 2009, 14 accidents in 2010, and 16 in 2011. We here report the results of our analysis of information obtained by detailed inspection for those that occurred from 2008 to 2010. We focused on vehicle-to-pedestrian accidents, which accounted for about 45% of all accidents in 2008. Because many accidents occurred on residential roads not far from pedestrians" homes, it was revealed that the decrease of the collision speed by traffic calming such as humps and zone speed management, was highly effective. On the other hand, pedestrian detection technologies seemed to be also effective as a countermeasure on vehicle side. Every pedestrian position against a vehicle was clarified and TTC (Time to Collision) was calculated provisionally. Pedestrian accidents in intersections were also examined. Among the intersection pedestrian accidents within the jurisdiction, compared with the national average in Japan, the ratio of intersections without a signal and the ratio without a pedestrian crossing were high. According to the comparison of the Japanese traffic accident patterns between 2001 and 2008, pedestrian accidents during turning right and turning left did not decrease much. For elderly drivers, these accidents occurred very often. Finally, single vehicle accidents were analysed with the accident pattern analysis methods used above. There were high numbers of single vehicle accidents against object on single roads. Although fatal accidents against guardrails decreased, the numbers of fatal accidents against a utility pole and a sign pole were nearly constant. As for the impact with narrow width objects such as utility poles, the fatality rate was very high, and countermeasures of both road infrastructure and vehicles seem to be effective.
A concept for Safe-Driving-Trainings with a focus on risky behavior and safety related attitudes has been evaluated. 519 participants have been tested before and after the training by means of a questionnaire with the topics: technical driving competence, awareness of risks, and propensity for anticipation. A control group (131 subjects) was used to check for the possibility of response artifacts. Three months later, 92 members of the treatment group and 25 members of the control group have been tested again. The results show significant positive changes in driving competence, risk awareness, and safety related attitudes, especially anticipation, due to the training. Compared to the control group the participants have become more risk aware and they regard of risk avoiding behavior as more important. The results show that this concept for Safe-Driving-Trainings has not only short-term but, more importantly, long-term positive effects on the safety-relevant attitudes and cognitions of young drivers.
The paper aims to study the injury risk and kinematics of pedestrians involved in different passenger vehicle collisions. Furthermore, the difference of pedestrian kinematics in the accidents involved minivan and sedan was analyzed. The 18 sample cases of passenger car to pedestrian collisions were selected from the database of In-depth Investigation of Vehicle Accident in Changsha of China (IVAC),of which the 12 pedestrian accidents involved in a minivan impact for each case, and the 6 accidents in a sedan impact for each. The selected cases were reconstructed by using mathematical models of pedestrians and accident vehicles in a multi-body dynamic code MADYMO environment. The logistic regression models of the risks for pedestrian AIS 3+ injuries and fatalities were developed in terms of vehicle impact speed by analyzing the minivan-pedestrian and sedan-pedestrian accidents. The difference of pedestrian kinematics was identified by comparing the results from reconstructed pedestrian accidents between the minivans and sedans collisions. The result shows that there is a significant correlation among the impact speed and the severity of pedestrian injuries. The minivan poses greater risk to pedestrian than sedan at the same impact speed. The kinematics of pedestrian was greatly influenced by vehicle front shape.
This study analyses no.39 cases in which n.41 motorcyclists were fatally injured, or 36% of total motorcycle fatalities in Northern Ireland between 2004 and 2010 (n.114). There were n.17 cases (43.6%) where the actions of another vehicle driver caused the collision, in thirteen of these cases the motorcycles had their lights switched on. The remaining n.22 collisions (56.4%) were due to the actions of the motorcyclist. In the approach to the collision scene, there were n.13 cases (31.7%) in which the approach was a right hand bend and in n.8 (19.5%) cases, the approach was a left hand bend. In the remaining n.18 (43.9%) cases, the approach was a straight road. Of the n.17 (41.4%) motorcycles that slid after falling, n.10 (24.4%) fell onto their right side and the remaining n.7 (17.1%) fell onto their left side. The information from this study identifies primary and contributory causes of motorcycle collisions.
The misuse of CRS (child restraint system) is one of the most urgent problems in connection of child safety in cars. Numerous field studies show that more than two thirds of all CRS are used in a wrong way. This misuse could lead to serious injuries for the children. Surprisingly the quality of CRS use is coded much better in accident data (e.g. GIDAS) than the results of observatory field studies show. It is expected that misuse of CRS was not detected by the accident teams in a large number of the cases. An essential part in improving child seats and their usability is the knowledge of the relation between misuse and resulting injuries. For that the analysis and experimental reconstruction of accidents is an important part. For allowing an exact experimental accident reconstruction, it is necessary to have detailed information about the securing situation of the child and about the installation of the CRS in the car.
Automotive interiors have long been a potentially injurious impact area to occupants during accidents, especially in the absence of adequate padding. The U.S. Federal Motor Vehicle Safety Standard (FMVSS) 201, Occupant Protection in Interior Impact, outlines test procedures and performance criteria in order to mitigate potentially injurious head impacts to interior surfaces. FMVSS 201 specifies a finite set of impact locations and applies to passenger vehicles of a specified year range and with a gross vehicle weight rating less than 10,000 lb. In this paper, two head impact test methodologies are presented, a pendulum-test device and a Free Motion Headform (FMH) launching device, which allows for dynamic, repeatable impact evaluation of various vehicle interior surfaces and their impact attenuation abilities. The presented testing includes multiple series that evaluate the effect of differing vehicle upper interior padding on occupant head injury. One study in particular, analyzes a head impact to the side header of a heavy truck (not included in FMVSS 201) during a 90 degree rollover. Additionally, two other series of tests are presented which assess the injury reduction effect of side airbags to near side as well as far side occupants in a side impact scenario. Lastly, a forensic analysis is presented which evaluates two possible head impact locations experienced in a real world accident by analysis of the resulting interior compartment damage utilizing the FMH launching device test method. The data collected and presented includes accelerometer instrumentation and high speed video analysis. These studies demonstrate that adequate padding and airbags are very effective at mitigating head injury potential at impact speeds of 12-25 mph (19-40 kph).
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
Supervision of the safety performance in public transport is one of the main tasks of the Federal Office of Transport (FOT) in Switzerland. Recently a three level system of safety indicators has been defined to cover all means of Swiss public transport. The safety indicators are fed by the FOT incident database since the year 2000. In cooperation with the Institute for Traffic Safety and Automation Engineering (iVA) at TU Braunschweig, Germany, FOT is developing a suitable methodology for the definition and evaluation of the safety targets in Swiss public transport. The methodology is applied for evaluation of safety indicators on a country level and for single transport companies. In a new approach the abovementioned methodology is applied to car incident data to develop an indicator based cross-modal safety measure.
The effect of fatigue on driving has been compared to the effect of alcohol impairment in both driver performance and crash studies. However are crash characteristics and causation mechanisms similar in crashes involving fatigue to those involving alcohol when studied in the real world? This has been explored by examining data held in the EC project SafetyNet Accident Causation Database. Causation data was recorded using the SafetyNet Accident Causation System (SNACS). The focus was on Cars/MPV crashes and drivers assigned the SNACS code Alcohol or Fatigue. The Alcohol group included 44 drivers and the Fatigue group included 47. "Incorrect direction" was a frequently occurring critical event in both the Alcohol and Fatigue groups. The Alcohol group had more contributory factors related to decision making and the Fatigue group had more contributory factors relating to incorrect observations. This analysis does not allow for generalised statements about the significance of the similarities and differences between crashes involving alcohol and fatigue, however the observed differences do suggest that attempts to quantify the effect of fatigue by using levels of alcohol impairment as a benchmark should be done with care.
Real world accident reconstruction with the Total Human Model for Safety (THUMS) in Pam-Crash
(2013)
Further improvement of vehicle safety needs detailed analysis of real world accidents. According to GIDAS (German In-Depth Accident Study) most car to car front accidents occur at mid-crash severity. In this range thoracic injuries already occur. In this study a real world frontal crash with mid-crash severity out of the AARU database was reconstructed. The selected car to car accident was reconstructed by AARU by means of pc-crash software in order to get the initial dynamic accident conditions. These initial conditions were used to reconstruct the complete accident in more detail using FE models for the car structure and the occupants. Occupant simulations were performed with FE HIII-dummy models and the THUMS using Pam-Crash code. An initial THUMS validation was performed in order to verify the model-´s biofidelity by means of table-top test simulations. THUMS bone stiffness values were modified to match the real word occupant age. A comparison between driver and passenger restraint system loading was done, as well as an injury prediction comparison between the HIII-dummy model and THUMS response for both cases. Detailed comparison between the HIII-dummy models and THUMS regarding thoracic loading are discussed.
With an ever rising human life expectancy the share of elderly people in society is constantly rising. This leads to the fact that at the same rate the share of people with age related diseases such as dementia and poor eyesight taking part in traffic will rise and therefore traffic accidents caused by this group of people due to the disease will play an ever greater role. This Situation will be among the future challenges of road safety work. At present this study displays specific characteristics of accidents caused by elderly car drivers (aged 65 or higher) based on the analysis of the German In-Depth Accident Study GIDAS. Herein almost 1000 elderly car drivers were identified as accident participants in the years 2008 to 2011. The focus of this study lies on identifying special types of accidents which are caused by elderly drivers and on characterizing these types with the information gathered on scene and by interviewing the participants. The main evidence analyzed is the knowledge about the accident locality, the trajectories of the participants as well as the reasons for the occurrence of the accidents. Furthermore personal information such as the personal condition before the accident and driving purposes is used to identify patterns of contributing circumstances for accidents caused by elderly traffic participants.
Beside numerous information about vehicles injuries and environmental data the GIDAS database contains detailed reconstruction data. This data is calculated by a reconstruction engineer who handles about 1000 accidents per year. The spectrum of one reconstruction ranges from simple crossing accidents to complex run-off accidents with rollover events. Especially for complex accident scenarios there is a large effort to design the environment of the accident scene within PC-Crash ®. To reduce the reconstruction time by maintaining the high quality of reconstruction 3D-geodata can be useful. Geodata is available for nearly every area in Germany and can be used for a fast and detailed creation of complex accident environments. In combination with the accident sketch areal images of the accident scene can be created and the participants are implemented in the new-built 3D-reconstruction environment. As a consequence, the characteristics of the terrain can be considered within the reconstruction which is especially important for run-off accidents.
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
The GIDAS-investigation team of Dresden (VUFO) has documented more than 11.500 accidents since 1999. The documentation of the accident includes beside vehicle-, injury- and environmental-data very detailed reconstruction data. Within this accident investigation the VUFO began to record the skid resistance of the accident site in 2009. The measurements are divided in macro- and microroughness (Sand depth method and Portable Skid Resistance Tester-SRT-by Munro-Stanley London-©). Both methods are used to determine the skid resistance for more than 1000 passenger cars. The aim of the present study is to find out a relationship between the measured skid resistance, the road conditions and the friction coefficient, which is used to calculate the maximum accelerations and decelerations during a reconstruction of an accident. Basic approach to convert the SRT-value into the friction coefficient is the calculation of the theoretical absorbed energy of the spring rubber system of the swinging arm of lever. This absorbed energy is used to get the friction coefficient by using the equations for the work of friction. To consider the road-behavior, in correlation to the friction coefficient, the results will be merged with existing literature. Last step for this study will be a comparison between actual used friction coefficients all over the GIDAS-database and the theoretical results. The study shows, if it is possible to use the SRT-Measurement for the estimation of a friction coefficient for the reconstruction of a traffic accident. As expected, the GIDAS-Database and the additional measurement of the roughness of the road directly on the spot are an enormous useful dataset.
The grip between the road surface and vehicle tires is the physical basis for the moving of all vehicles in road traffic. In case of an accident the available grip level is one of the most relevant influence factors, influencing the causation and the procedure of the accident. However, the estimation of the grip level is not easy and therefore, is commonly not done on the accident scene. This is especially true for the measurement of the water depth. Until now, real accident databases provide no measurement data about the grip level and the water film depth and thus, the estimation of its influence is not possible yet. From the tyre manufacturers point of view, it is important to know about the road conditions (namely grip level, macro-texture, water depth, temperature) at the accident scene, as well as the operating conditions of the vehicles (braking, loss of control, speed, etc). These data is necessary to define relevant tyre traction tests for the end-user and for regulations. For this reason VUFO and Michelin developed a consistent method for the measurements of grip level and water depth for the accidents of the GIDAS database. The accident research team of Dresden, which documents about 1000 accidents with at least one injured person every year, is measuring the micro-roughness and the macro-roughness directly on the spot. For the measurement of the micro-roughness a Skid Resistance Tester (British Pendulum) is used. The Mean Texture Depth (describing the macro-roughness) is measured by the Sand Depth Method. Since June 2009, measurements for more than 700 accidents including 1200 participants have been carried out. In case of wet or damp road conditions during the accident, the water depth is measured additionally. Therefore VUFO and Michelin developed a special measurement device, which allows measurements with an accuracy of 1/10 millimetre. The measurement point at the accident scene is clearly defined and thus, the results are comparable for all different accidents and participants. The use of the GIDAS database and the accident sampling plan allows representative statements for the German accident scenario. With this data it is possible for the first time to have an accurate view of the road conditions at the accident scene. One possibility is a more detailed estimation of hydroplaning accidents using the actually measured water depths. The development of new testing methods and new tires can be based on the real situation of the road infrastructure. Furthermore, the combination of the technical GIDAS data and the measured road surface properties can also be used for the estimation of effectiveness of several safety systems like the brake assist and/or emergency braking systems. The calculation of a reduced collision speed due to the use of a brake assist is only one example for the application of real measured grip level data.
Having a look at safety to traffic and the prevention of accidents it can be observed that technical improvements in active safety of vehicles have let to various positive effects in this area. Among other components the tyre-road-contact takes a key role in the development of active safety technologies. All forces in accelerating, breaking and vehicle guidance have to be transmitted through the tyre-road contact area by friction forces. A common way to characterize a friction process is to identify the coefficient of friction μ between two touching materials. Even though there are several approaches to experimentially characterise road surfaces, no standard method exists. In this paper an overview of existing test methods is given. Furthermore the preliminary design of a newly developed portable test device with its possibility to investigate the tyre-road-friction of arbitrary roads or even places of accidents is shown.
The European CASPER (Child Advanced Safety Project for European Roads) project studying car child safety includes a sociological approach in order to have a better understanding of the behaviour of parents driving children under 12 years old. A questionnaire was distributed via the internet in Europe with 998 parents (representing 1638 children) from 22 European countries responding. The results inform on the way parents secure their children during a car trip. Many parents did not control how their children were installed in the child restraint system (CRS). A toddler was more likely to travel into a child seat than an older child was. Regarding misuse situations, an important part of the participants did not think that they could make mistakes when fixing the child seat to the car (26%) or when placing the child into the seat (39%). This leaves an important field of action especially by communication via different media and in the CRS sale outlets.
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
The utilisation of secondary-safety systems to protect occupants has attained a very high level over the past decades. Further improvements are still possible, but increasingly minor progress is only to be had with a high degree of effort. Thus, a key aspect must be the impact to overall safety in an accident. If reliable information is available on an imminent crash, measures already taken in the pre-crash phase can result in a significantly great influence on the outcomes of the crash. With this background preventive measures are the key to a sustainable further reduction of the figures of crash victims on our roads. This paper aims to show a preventive approach that can contribute to lessening the consequences of a crash by creating an optimum interaction of measures in the fields of primary and secondary safety. To further enhance vehicle safety, driver assistant systems are already available that warn the driver of an imminent front-to-rear-end crash. The next step is to support him in his reactions or if he fails to react sufficiently, to even initiate an automatic braking when the crash becomes unavoidable. Automatic pre-crash braking can, in an ideal situation, fully prevent a crash or can significantly reduce the impact speed and thus the impact energy (and the severity of the accident). If a vehicle is being braked in the pre-crash phase, the occupants are already being pre-stressed by the deceleration. The information available about the imminent crash can be used to activate the belt tensioners and likewise other secondary safety systems in the vehicle right before the impact. The pre-crash deceleration also causes the front of the vehicle to dip. Conventional crash tests do not take this specific impact situation into consideration. This is why, for example, the influences of the pre-crash displacements of the occupants are not recorded in the test results. Furthermore, a reproducible representation of the benefit of the vehicle safety systems which prepare the occupants for the imminent impact is not possible. In order to demonstrate the functions of automated pre-crash braking and to investigate the differences during the impact as a consequence of the altered occupant positions as well as the initiation of force and deformations of the vehicle front, DEKRA teamed up with BMW to carry out a joint crash test with the latest BMW 5 series vehicle. It involved the vehicle braking automatically from a starting test speed of 64 km/h (corresponding to the impact speed set by Euro NCAP) down to 40 km/h. The test was still run by the intelligent drive system of the crash test facility. This required several modifications to be made to the test facility as well as to the vehicle. The paper will describe and discuss some relevant results of the crash test. In addition, the possible benefits of such systems will also be considered. The test supplemented the work of the vFSS working group (vFSS stands advanced Forward-looking Safety Systems).
Nowadays human-created systems are increasing in complexity due to the interaction of humans and technology. Especially road traffic systems are composed of multitudinous resources (e.g. personnel, vehicles, organizations, etc.), which make it even harder to anticipate the positive and negative effects on safety. One key in achieving a significant reduction of fatalities is seen in driver assistant systems counterbalancing the lack of drivers' capabilities. But the actual outcome of implementing these sophisticated technologies especially on influencing driver's capabilities are yet unknown. Latest research exemplifies an increase of reaction times of drivers in case of dysfunctional driver assistant systems. This research paper applies STAMP/STPA (STAMP = systems-theoretic accident model and processes; STPA = systems-theoretic process analysis) to the German automobile traffic system focusing on the effects of driver assistant systems on drivers. By doing so, the potential hazards caused by technology can be identified.
The sequence of accident events can be classified by three essential phases, the pre-crash-sequence, the crash-sequence and the post-crash-sequence. The level of reliability of the information in the GIDAS-database (German In Depth Accident Study) is provided predominantly on the passive side. The period to evaluate active safety systems begins already in the pre-crash-sequence. The assessment of the potential of sensor- or communication-based active safety systems can only be accomplished by a detailed analysis of the pre-crash-phase. Hence the necessity to analyze the early period of the accident event in detail arises. This is possible with the help of the digital sketches of the accident site and the simulation of the accident by a simulation method of the VUFO GmbH. After simulating the pre-crash scenario it is possible to generate additional and standardized data to describe the pre-crash-sequences of an accident in a very high detail. These data are documented in a second database called the GIDAS Pre-Crash-Matrix (PCM). The PCM contains various tables with all relevant data to reproduce the pre-crash-sequence of traffic accidents from the GIDAS database until 5 seconds before the first collision. This includes parameters to describe the environment data, participant data and motion or dynamic data. This paper explains the creation of the PCM, the simulation itself and the contents and structure of the PCM. With this information of the pre-crash-sequence for various accident scenarios an improved benefit estimation and development of active safety systems can be made possible.
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
To date, the Trauma Registry (TraumaRegister DGU-® contains data of approximately 100.000 severely injured patients, 65% of which suffered from a road traffic crash. Thus, it is the world's largest data base for severely injured patients. The article describes the development of the registry and explains how it was rolled out over Germany using the established structure of the German Trauma Network (TraumaNetzwerk DGU-®). In addition, this article presents three typical use cases from the fields of quality management, policy making and system-wide interventions, clinical research and injury prevention. In conclusion, the TraumaRegister DGU-® is a well-established tool for various purposes related to the control and reduction of the burden of road injury. Its ongoing expansion to other countries will support the goal of international benchmarking of hospitals and trauma systems.
The number of injured car occupants decreases constantly. Nevertheless, they account for nearly 50% of all fatalities and about 44% of all seriously injured persons in German traffic accidents. Further reductions of casualties require multiple efforts in all parts of traffic safety. In this paper a detailed analysis of the important pre-hospital rescue phase was done. The basis for future improvements is the knowledge about injury causation of car occupants in combination with other corresponding influence factors. For that reason more than 1.200 severe (AIS3+) injuries of frontal car occupants were analyzed. For the most relevant injuries of car occupants multivariate analysis models were created to predict the probability of these injuries in a real crash scenario. In addition to the collision severity different influence factors like impact direction, seat belt usage, age of the occupant, and gender were analyzed. Furthermore, the models were checked regarding the goodness of fit and all results all results were checked concerning their robustness. The prediction models were created on the basis of 5.000 car accidents. Afterwards, the models were validated using 4.000 different car accidents. The prediction of the probability of severe injuries could be used for different applications in the field of traffic safety. One possibility is the implementation of the models in a tool for the on-the-spot diagnosis. The background for the development of such applications is the fact, that there are only limited diagnostic possibilities available at the accident scene. Nevertheless, the rescue forces have to make essential decisions like the alerting of the necessary medical experts, appropriate treatment, the type of transportation and the choice of an adequate hospital. These decisions quite often decide between life and death or influence the long-term effects of injured persons. At this point, indications of expectable injuries could help enormously. To enable even persons with limited technical knowledge to use the tool, a procedure was developed that facilitates the assumption of the given crash severity. Another important possibility for the application of the prediction models is the use for the qualification of information sent by e-call systems.
Introduction: Spine injuries pose a considerable risk to life and quality of life. The total number of road deaths in developed countries has markedly decreased, e.g. in Germany from over 20000 in 1970 to less than 4000 in 2010, but little is known how this is reflected in the burden of spine fractures of motor vehicle users. In this study, we aimed to show the actual incidence of spine injuries among drivers and front passengers and elucidate possible dependencies between crash mechanisms and types of injuries.
The objective of the study is to measure the risk of pedestrian and bicyclist in urban traffic through an analysis of real-world accident data. The kinematics and injury mechanisms for both pedestrian and bicyclists are investigated to find the correlation of injury risks with injury related parameters. For this purpose, firstly 338 cases are selected as a sample from an IVAC accident database based on the In-depth Investigation of Vehicle Accident in Changsha of China. A statistic measurement of the fatality and serious injury risks with respect to impact speed was carried out by logistic regression analysis. Secondly, 12 pedestrian and 12 bicyclist accidents were further selected for reconstruction with MADYMO program. A comparative analysis was conducted based on the results from accident analysis and computer reconstructions for the injury risk, head impact conditions and dynamic response of pedestrians and bicyclists. The results indicate that bicyclists suffered lower risks of severe injuries and fatalities compared with pedestrians. The risks of AIS 3+ injury and fatality are 50% for pedestrians at impact speeds of 53.2 km/h and 63.3 km/h, respectively, while that for bicyclists at 62.5 km/h and 71.1 km/h, respectively. The findings could have a contribution to get a better understanding of pedestrians" and bicyclists" exposures in urban traffic in China, and provide background knowledge to generate strategies for pedestrian protection.
From literature well-known analyzes on risks, hazards and causes of accidents of older drivers are amended by the present study in which a comparison of the specific features of accident causes of older car drivers (older than 60 years) and of younger car drivers (under 25 years) is conducted. Mainly the question is pursued if specific errors, mistakes and lapses are predominant in the two different age groups. The analysis system ACAS (Accident Causation Analysis System) used hereby consists of a sequential system of accident causation factors from the human, the technical and the infrastructural field, whereupon for this study the influence of the human features on the accident development in two different age groups is of interest. ACAS is both an accident model and an analysis and classification system, which describes the human participation factors of an accident and their causes in the temporal sequence (from the perceptibility to concrete action errors) taking into consideration the logical sequence of individual basic functions. In five steps (categories) of a logical and temporal sequence the hierarchical system makes human functions and processes as determinants of accident causes identifiable. The methodology specifically focuses on the use in so-called "In-Depth" and "On-Scene" investigation studies. With the help of the system for each accident participant one or more of five hypotheses of human cause factors are formed and then specified by appropriate verification criteria. These hypotheses in turn are further specified by indicators in such manner that the coding of the causation factors by a code system meets the needs of database processing and are accessible to a quantitative data analysis. The first results of the descriptive comparison of the two age groups concern mainly differences in the functional levels "information admission/perception" (where the elderly drivers have more difficulties than the young ones) and "information processing/evaluation" (where the younger drivers show more problems). Concerning the cognitive function of "planning" the group of younger drivers seems to be more often involved in an accident because of excessive speed.
In 2012 the fifth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Injuries in motorbike accidents in correlation with protective clothes and mechanism of the accident
(2013)
This study deals with a possible connection between safety clothing / accident mechanism and injury severity in a state-wide traffic accident investigation with focus on light and small motorbike-involvement for accidents in the area of the Saarland in which the persons riding the bike have been injured or killed. An interdisciplinary team of medical scientists and engineers collected the medical and technical data as well as all the relevant traces of the accident on scene and in time. During twenty months of data collection a total of 401 cases could be gathered. Grave injuries were more common for the group of heavier motorcycles (>125 ccm). Motorcyclists had been polytraumatized only in the group where the accident was connected with a collision. Significant correlation between protective clothes and injury severity could only be found for protective gloves and protective trousers. The knowledge about mechanism of the accident, protective clothes and severity of injuries can be helpful for the improvement of road and motorcyclists' safety.
Cycle helmets have continued to increase in popularity since their introduction half a century ago. Many studies indicate that overall, head injury can be significantly reduced by wearing them. This study was conducted using two distinct sets of real-world cycling collision data from Ireland, namely cases involving police collision reports and cases involving admission to a hospital emergency department. The analyses sought to simulate and analyse the protective performance of cycle helmets in such collision scenarios, by comparing the Head Injury Criterion score and peak head accelerations, both linear and angular. Cycle collisions were simulated using the specialised commercial software MADYMO. From the simulation results, these key metrics were compared between the same-scenario helmeted and unhelmeted cyclist models. Results showed that the inclusion of bicycle helmets reduced linear accelerations very significantly, but also increased angular accelerations significantly compared to unhelmeted situations. Given the modest protective performance of cycle helmets against angular accelerations, it is recommended that cycle helmet manufacturers and international test standards need to pay more attention to head angular accelerations.
MANSSEN diskutiert das Generalthema des Forschungsseminars, ob sich "das straßenrechtliche Nutzungsregime" tatsächlich im Umbruch befindet und diagnostiziert eine Gewichtsverschiebung vom Straßenrecht hin zum Straßenverkehrsrecht. Das klassische Straßenrecht habe immer weniger zur Weiterentwicklung des Straßenwesens beizutragen. In diesem Zusammenhang behandelt er auch neue Verkehrskonzepte wie "Simply City" und "Shared Space". SIEGELs Beitrag über Grundrechtsgebrauch auf öffentlichen Straßen verdeutlicht anhand aktueller Beispiele die praktische Bedeutung des Straßenrechts bei der Verwirklichung von Grundrechten. Nach seiner Einschätzung verfügt das Straßenrecht insoweit nach wie vor ein adäquates Steuerungspotenzial. Etwaige Lücken könnten durch das Straßenverkehrsrecht, vor allem aber durch eine ergänzende Heranziehung des Polizeirechts geschlossen werden. Der Beitrag von ENDERLE über "Grenzüberschreitende Infrastrukturen " Planungs- und naturschutzrechtliche Besonderheiten" bezieht sein Anschauungsmaterial von dem Projekt der Fehmarnbelt-Querung. Als typische Abstimmungsprobleme bei der Planung und Genehmigung grenzüberschreitender Projekte behandelt sie namentlich die Frage der Linienbestimmung sowie grenzüberschreitende Verträglichkeitsprüfungen für FFH- und Vogelschutzgebiete. Der abschließende Beitrag von DURNER "Das Netzausbaubeschleunigungsgesetz 2011" stellt dar, dass die in diesem Gesetz geschaffene neue "Fachplanung" des Bundes teils Elemente des Raumordnungsverfahrens, teilweise jedoch auch solche der straßenrechtlichen Linienbestimmung und der standortbezogenen Raumordnungsziele aufweist. Letztlich folgt die Bundesfachplanung im Hinblick auf die Bindungswirkung im Wesentlichen dem Modell des -§ 4 ROG. Das Modell des NABEG mag für den Netzausbau sachgerecht sein, erscheint jedoch im sonstigen Infrastrukturbereich unrealistisch.
Im Jahr 2004 fand an der Medizinischen Hochschule Hannover die erste ESAR-Konferenz (Expert Symposium on Accident Research) statt. Die Idee einer internationalen Konferenz war aus der Notwendigkeit entstanden, diejenigen Experten zusammen zu bringen, die weltweit tätig sind und Verkehrsunfälle wissenschaftlich analysieren, um ihre Ergebnisse gemeinsam zu diskutieren und einem Zielpublikum von Behördenvertretern, Entwicklungsingenieuren der Automobilindustrie und anderen Wissenschaftlern darzubringen. Die durch Professor Otte initiierte und nun zum vierten Male organisierte Konferenz fand eine breite Akzeptanz und ist mittlerweile Bestandteil einer Konferenzlandschaft mit Zielvorträgen von der Fahrzeugsicherheit bis hin zur Verletzungsanalyse und den Unfallursachen. ESAR kann als wissenschaftliches Kolloquium und Plattform für einen Informationsaustausch der Unfallforscher angesehen werden, die sich speziell mit Methoden der Unfalluntersuchung, mit Verletzungsmechanismen und der Bewertung von Verletzungen, Unfallursachen und anderen Bereichen der statistischen Unfalldatenanalyse befassen. Experten aus den Bereichen der Medizin, der Verkehrspsychologie und der Technik sowie Vertreter zuständiger Behörden kommen hier zusammen, um die Erfahrungen in der Unfallprävention und der Unfallrekonstruktion zu diskutieren und um der Forschung neue Felder zu eröffnen. Neben den Belangen der Europäischen Gemeinschaft werden auch die weltweit zu registrierenden hohen Verletztenzahlen berücksichtigt. Wissenschaftliche Vorträge aus aller Welt tragen dazu bei, geeignete Maßnahmen und Methoden zur Analyse und drastischen Verringerung der Zahl der bei Verkehrsunfällen Getöteten zu entwickeln. Die Zusammensetzung des Teilnehmerkreises dieser wie früherer ESAR-Konferenzen hat längst eine über Europa hinausgreifende Internationalitaet erreicht und bietet daher einen aufschlussreichen Überblick über die verschiedenen Standards bestehender Verkehrssicherheit und unterschiedlichen Unfallszenarien und über die Anforderungen an die Unfallanalysen. Die Ergebnisse langjähriger Forschungsarbeiten in Europa, USA, Australien und asiatischen Ländern beinhalten unterschiedliche infrastrukturelle Zusammenhänge und geben Erkenntnisse über Population, Fahrzeugbestand und Fahrereigenschaften. Derartige Informationen bilden eine exzellente Basis für abzuleitende Empfehlungen und Maßnahmen für die Erhöhung der Verkehrssicherheit international.
Im Rahmen des zweitägigen Kolloquiums "Luftqualität an Straßen 2013" wurden aktuelle Forschungsaktivitäten und Maßnahmen auf dem Gebiet der Luftreinhaltung im Einflussbereich von Straßenbau und Straßenverkehr vorgestellt. Der Tagungsband gibt 14 Fachvorträge und die 4 Beiträge der Posterausstellung wieder.
Entgegen populären Meinungen, welche älteren Kraftfahrern ein generelles Gefahrenpotenzial für die allgemeine Verkehrssicherheit zuschreiben, weisen die Unfallstatistiken eher auf eine besondere Gefährdung dieser Gruppe von Verkehrsteilnehmern hin, woraus sich Forderungen nach einer zielgruppenspezifischen Verkehrssicherheitsarbeit begründen. Kompetentes und damit sicheres Verhalten kann als Ergebnis der Passung zwischen den individuell verfügbaren Ressourcen und den Anforderungen der Umwelt betrachtet werden. Überschreiten die Umweltanforderungen die Verhaltenspotenziale des Individuums, kann es zu Überforderung kommen. Verdeutlichen lässt sich diese Perspektive durch genaue Betrachtung von Verkehrsunfällen unter Beteiligung älterer Kraftfahrer: So spiegeln die aktuellen Unfallstatistiken aus 2008 wider, dass ein großer Teil der Unfälle von Kraftfahrern im Alter über 65 Jahren auf sogenanntes Fehlverhalten in Knoten, wie z.B. Fehler beim Abbiegen, Ein- und Ausfahren in Kreuzungen und Vorfahrtbeachtung, zurückzuführen sind. Diese im Vergleich zu jüngeren Fahrern häufigere Verwicklung Älterer in Unfälle dieser Art legt nahe, dass es in genau diesen Situationen zu einem Ungleichgewicht zwischen individuell verfügbaren Ressourcen und den Anforderungen der Verkehrsumwelt kommt. Beispielsweise könnten in diesen Situationen Beeinträchtigungen der visuellen Wahrnehmungsfähigkeit, verlangsamte Reaktionszeiten oder auch Einschränkungen der Bewegungsausführung zu einer zu langsamen oder auch falschen Entscheidungsfindung oder Handlungsausführung im Straßenverkehr führen. Dieser Perspektive folgend können Maßnahmen zur Erhöhung der Verkehrssicherheit älterer Kraftfahrer zum einen auf Seiten des Individuums ansetzen und dazu beitragen, die Kompetenzen des älteren Kraftfahrers zu erhöhen, zum anderen Bezug auf den Kontext nehmen, indem durch Anpassungen der Bedingungen der Verkehrsumwelt zur Sicherheit " nicht nur " älterer Kraftfahrer beigetragen wird. Personenzentrierte Ansätze zielen dabei auf die Ausschöpfung der individuellen Potenziale zur Aufrechterhaltung, Verbesserung oder auch Wiederherstellung einer sicheren Verkehrsteilnahme bis ins hohe Lebensalter. Diese Ansätze umfassen Trainings- und Rehabilitationsprogramme der Fahrkompetenz gleichermaßen wie verkehrspädagogische Programme, mediale Informationskampagnen oder auch Beratungsmaßnahmen und Screening-Tests. Eine Schlüsselposition kann in diesem Kontext dem (Haus)-Arzt als Experten hinsichtlich Konstitution und Lebensverhältnissen seines Patienten und Vertrauensperson zukommen. In der Regel passen ältere Kraftfahrer ihr Fahrverhalten ihren individuell verfügbaren Kompetenzen an. Auf diese Weise können altersbegleitende oder auch mit Erkrankungen oder Medikamenteneinnahmen einhergehende Veränderungen der körperlichen oder geistigen Leistungsfähigkeit zumeist erfolgreich kompensiert werden. Personenzentrierten Ansätzen kommt jedoch eine besondere Relevanz für den kleinen Anteil älterer Fahrer zu, welche keine oder nur unzureichende Kompensation aufweisen. Kontextorientierte Ansätze beziehen sich auf Maßnahmen, welche eine möglichst optimale Gestaltung der Bedingungen der Verkehrsumwelt auf die Bedürfnisse und Anforderungen älterer Kraftfahrer herbeiführen sollen. Maßnahmen dieser Art zielen zum Beispiel auf eine Entschleunigung des Straßenverkehrs durch Geschwindigkeitsbegrenzungen oder auch bauliche Maßnahmen. Auch die Potenziale moderner Fahrzeugtechnik werden unter dieser Perspektive zur Erhöhung der Verkehrssicherheit älterer Fahrer nutzbar. So können Fahrerassistenz- oder Fahrerinformationssysteme den älteren Fahrer in komplexen Situationen unterstützen. Dabei ist der Nutzen für die Verkehrssicherheit jedoch stark von der Handhabbarkeit und Bedienqualität der technischen Hilfsmittel abhängig. Technologien, welche die Komplexität der Fahrzeugbedienung erheblich erhöhen oder die Aufmerksamkeit vom Straßenverkehr ablenken, können ggf. auch zu einer weiteren Diskrepanz zwischen Anforderungssituation und verfügbaren Kompetenzen beitragen. Neben diesen eher auf die individuelle Verkehrsteilnahme als Autofahrer bezogenen Maßnahmen sind weitere wichtige kontextorientierte Ansatzpunkte in alternativen Mobilitätsvarianten zum Auto, wie in der Verbesserung der Attraktivität von Angeboten des ÖPNV oder auch den Bedingungen für Fußgänger und Radfahrer, zu finden. In diesem Sinne erscheint ein mehrdimensionaler Ansatz für die Gestaltung von Maßnahmen zur Erhöhung der Verkehrssicherheit älterer Kraftfahrer am erfolgversprechendsten. Interventionsansätze sollten sich gegenseitig ergänzen und möglichst sowohl die Ressourcen auf Seiten des älteren Menschen selbst als auch der Umwelt umfassen.
The National Roads Authority in Ireland is responsible for planning and supervision of construction and maintenance works on the National Road network. Its primary function is "to secure the provision of a safe and efficient network of national roads". The population of Ireland has grown rapidly from 3.5 million to 4 million within the past 10 years, and vehicle ownership has also risen rapidly to 2 million vehicles, with 2.2 million drivers. Collisions rates in Ireland are at approximately 1.5 collisions per 1,000 population (in 2002), and 8.4 deaths per 1,000,000 population (in 2003). This ranked 8th out of the 15 countries in the European Union at the time. Ireland- current Road Safety Strategy includes Engineering Targets. These are to complete construction of certain lengths of new motorway, dual carriageway and 2+1 highway, to implement a certain number of accident remedial and traffic calming schemes, and to implement road safety audit on all new schemes. The accident remedial schemes, traffic calming schemes, and road safety audit are all the responsibility of the Road Safety section of NRA. The road safety programme of the NRA is divided into four main areas; a) accident remedial measures at individual sites, b) accident remedial treatment of entire routes, c) traffic calming of towns and villages on main roads, d) road safety audit. Examples of these measures are described. Evaluation of past programmes of single site accident remedial measures show a reduction in collision occurrence at these sites, but the effectiveness and the economic rate of return is decreasing over successive programmes. A similar programme has now been adopted on the rest of the country- road network, on regional and local roads. The programme of remedial treatment of entire routes has only recently started and has not been evaluated. Evaluation of the first programme of traffic calming of towns and villages shows an overall decrease in collisions and their severity, and a small reduction in speed. Road Safety Audit, examining new schemes a number of times during design and after construction, has been standard procedure on the national road network for nearly 6 years. An evaluation is currently underway.
Die EU hat für die Verkehrssicherheit in Europa ein anspruchsvolles Ziel vorgegeben: Bis 2010 soll die Anzahl der im Straßenverkehr Getöteten gegenüber 2000 halbiert werden. Für Deutschland kann eine erfolgreiche Zwischenbilanz gezogen werden: In den letzten 5 Jahren nahm trotz Vergrößerung des Kraftfahrzeugbestandes um 6% die Anzahl der Verkehrstoten um 29% ab, in den vergangenen 10 Jahren ist ein Rückgang um 43% zu verzeichnen. Diese im internationalen Vergleich überdurchschnittlichen Erfolge sind nicht zuletzt auch auf Fortschritte in der Fahrzeugtechnik zurückzuführen, wobei die zunehmende Verbreitung von Systemen der Aktiven Sicherheit wie ABS, BAS, ESP einen entscheidenden Anteil hat. Nach der deutlichen Reduzierung von Fahrunfällen durch ESP-® stehen nun die Auffahrunfälle im Fokus der Sicherheitsentwicklung von Mercedes-Benz. Das Paket aus verbessertem rückwärtigen Signalbild (Adaptives Bremslicht) und Brems-Assistent (BAS) wurde kürzlich durch radarbasierte Bremsassistenz ergänzt (BAS PLUS und PRE-SAFE-®-Bremse). Der Beitrag geht auf Funktion und Wirksamkeit der einzelnen Systeme ein und gibt einen Ausblick in die nähere Zukunft.
The Swedish "Vision Zero" regards road fatalities and severe injuries as unacceptable. The vision is based on this ethical perspective together with a fundament of shared responsibility between the system designers and the road user. The design of the traffic system shall protect the road user from these effects as long as he or she follows the traffic rules. It should be possible to make a mistake without being killed. This policy has, during the first period of the "vision zero" (since 1997) put high priority on road and car design where the purpose has been to develop a forgiving environment. Gradually it has, however, become clear that much more effort has to be focused on the responsibility of the road user. Protecting measures will have limited effect as long as the understanding and acceptance from road users is limited. During the last years, Sweden has gone through several improvements of the driver education and is in the middle of important improvements of road safety education for children in schools. Several EU-projects has contributed to this development. One aspect that has received large international interest is the lay instructed driver training from 16 years of age supervised by parents. This has been in use since 1993. Another is the development of mandatory courses, such as an introduction for the learner and the lay instructor, a "risk awareness" courses dealing specifically with speeding, seat belt use, drunk driving, tiredness, and driving on low friction. The presentation will share some of the "vision zero" fundaments together with the latest experiences, research and development concerning driver education in Sweden.
Mobil sein zählt zu den Grundbedürfnissen und im Rahmen des westlichen Wertesystems zu den Grundrechten von Menschen. Dies gilt umso mehr, je mobiler die Gesamtgesellschaft wird und je mehr Menschen im Zuge der demographischen Entwicklung zum Kreis der "älteren Menschen" zählen. Dementsprechend wertet der dritte Bericht zur Lage der älteren Generation in der Bundesrepublik Deutschland den Erhalt der Mobilität im Alter als Basis für die "Erschließbarkeit der verschiedensten Ressourcen der Außenwelt" und als "entscheidenden Faktor von Lebensqualität im Alter", d.h. Aufrechterhaltung der Unabhängigkeit der Lebensführung durch Bewahrung von Fertigkeiten inkl. der Ermutigung zur Mobilität spielt für Ältere eine besonders wichtige Rolle. Die Entwicklung von Interventionsansätzen zur Förderung einer lebenslangen, sicheren Mobilität älterer Menschen stellt eine gesamtgesellschaftliche Herausforderung dar. Dementsprechend lebendig ist die Diskussion über Möglichkeiten ältere Verkehrsteilnehmer/innen in der Erhaltung ihrer Mobilität zu unterstützen und die Forschungsaktivität auf diesem Gebiet. Im Vortrag werden u. a. folgende Bereiche thematisiert: - Senioren stellen keine homogene Gruppe dar; dieses gut erforschte Faktum gilt auch für ihr Mobilitätsverhalten, aber auch für das Risikoverhalten. Ältere Menschen sind durch ausgesprochene Vielfalt mobilitätsbezogener Erwartungen, Verhaltensmuster und Lebensstile charakterisiert. - Die gegenwärtig durchaus wachsende positive Bewertung und Einstellung gegenüber Alter und Altern muss bei der Entwicklung neuer Sicherheitsmodelle berücksichtigt werden, gar Vorteil sollte daraus gezogen werden. - Um höhere Straßenverkehrssicherheit - nicht nur für Ältere - zu erreichen, ist eine stärkere Orientierung auf schwache, ungeschützte, vulnerable Verkehrsteilnehmer notwendig. - Teilnahme am Straßenverkehr ist Ergebnis eines lebenslangen Lernprozesses. Mobilitätsgewohnheiten, die während des Lebenslaufes erworben wurden, werden auch im Alter (unter Einsatz diverser Kompensationsstrategien) zum Großteil beibehalten. - Technologische Systeme (z.B. Telematik) können Mobilitätsplanung erleichtern und (bis zu einem gewissen Grad) Verluste in Fertigkeiten und Fähigkeiten zur Verkehrsteilnahme kompensieren und auf diese Weise zur Unfallreduktion beitragen. Die Alterssensitivität der Systeme muss ein zentraler Entwicklungsbereich sein. - Es sollte eine sehr viel stärkere Beteiligung der Älteren an der Entwicklung, Einführung und Implementation von verkehrsbezogenen Sicherheitsmaßnahmen und neuen Technologien ermöglicht werden. - Augenmerk sollte auch auf "alternative" Mobilitätsformen gelenkt werden: Smart Modes (zu Fuß gehen, Radfahren). Auch die Nutzung des ÖPNV sollte dadurch erleichtert werden, dass er so "benutzerfreundlich" wie nur möglich wird. - Ältere haben weiterhin ein hohes Interesse an und eine positive Einstellung zu Lernen, Übung und Training. Dies gilt auch für technischen Fortschritt und moderne Entwicklungen bezüglich der Straßenverkehrssicherheit. - Wenn Verkehrssicherheitsmaßnahmen implementiert werden, sollten die Kommunikationsmöglichkeiten dergestalt genutzt werden, dass sie für die verschiedenen Lebenssituationen und Lebensstile der Älteren angemessen sind. "Neue" Medien können dabei durchaus in Betracht gezogen werden. Fachdisziplinen wie Politikwissenschaft, Verkehrswesen, Ingenieurwissenschaften, Raumplanung, Architektur, Soziologie, Medizin, Psychologie, Pädagogik, Rechtswissenschaften, Ökonomie und Ökologie müssen künftig kooperieren, um einen Synergie-Effekt im Bereich der Mobilitätsförderung und der Verkehrssicherheitsarbeit für ältere Verkehrsteilnehmer und Verkehrsteilnehmerinnen zu erzielen. Dabei ist eine enge, interdisziplinäre Zusammenarbeit notwendig - ebenso wie ein vorurteilsfreier Umgang der Menschen miteinander in unserer Gesellschaft.
Before 2002, France was in the queue of Europeans countries in terms of road safety results because of the low density of population and the faulty behaviour of French due itself to a very low level of traffic law enforcement Even if there were signs of the change of mind in France towards road safety before, the turning point was in summer 2002, when the President declared road safety as a priority work during his mandate. The more symbolic measure was the decision to settle an automatic speed control system (700 fixed and 300 mobile). Over three years, the average speed on French roads decreased by 5 km/h and the number of fatalities on road turned down from an average of 8000 deaths per year to 5 300, which represents a decrease of more than 34 %. For the next months, we anticipate that, as many drivers have kept loosing points on their driving licence through light speed violations, this will lead drivers to check their speed and the speed limits more systematically as loosing points on one's driving license has longer time effects than paying a fine. Consequently, we expect a decrease of 10 % to 15% of fatalities in 2006, which is a very good result if we compare with the trend of the last twenty five years (about 2,3 %). The reverse effect of this system that lies on the changes of behaviour of the majority is that, there is more and more discontent against the system taking into account that automatic speed control system allows only a minor tolerance above limits and that local speed limits are not always adapted to local infrastructure and traffic conditions. Another weakness of the system is that motorcyclists are too rarely caught by the system; the system is being gradually improved by placing the new speed cameras in position of taking photographs of the back of the vehicle. But this would not be sufficient to reduce the speed of motorcyclists that are a very high risk group (16% of fatalities for 0,8 % of traffic) For alcohol, there is no easy route for progress: all what is done nowadays is toward festive impaired driving (through designating sober drivers or mass alcohol preventive screenings) although there is not enough done towards chronic alcoholic driving.
Motorcycle safety research
(2007)
Honda- global motorcycle sales exceeded the 10 million units mark since 2004, and further expansion is expected. As a responsibility for a company to provide mobility, Honda is focusing on motorcycle safety as top priority and has been working on various activities for both aspects of hardware and software. Here, we present Honda- activity for the safety technology of motorcycles. At present, Honda is promoting motorcycle safety in the four themes of prevention and collision safety such as safety education, recognition assistance, accident prevention and injury reduction. First, in the area of the safety education, the "Honda Safety Driving Promotion Center" was established in 1970, and motorcycle riders and vehicle driver trainings have been organized, and the traffic training centers are used as an actual practice field not only in Japan but also in many other regions in the world. Through our training activities, the new area of safety training with hardware assistance was developed and Honda- unique technology was accumulated such as the riding simulator which can provide experience of potentially dangerous situations without risk. Especially, the "riding trainer", the popular version of the riding simulator, was introduced at several motor shows in various countries and launched in September 2005. It was distributed first in Europe and is expected to expand globally aiming at 3000 units worldwide.. And in Europe, the newest version, which includes the suburban roads program, jointly developed with ADAC, will be released in near future. In the area of recognition assistance, "vehicle to vehicle communication technology" is under development using the advantage of being a manufacturer of both motorcycles and cars. This technology is under research as Honda "ASV-3" in Japan, and as part of C2C activity in Europe. As for the accident prevention, advanced brake systems for motorcycles to assist more effective brake operation have been expanded, Honda signed the European Road Safety Charter in April 2004 with the advanced brake systems commitment and furthermore, they are expanding according to vehicle characteristics and region. Then all models above 250 cc will have a version of the system by 2010. And as the last theme, "motorcycle airbag system" is introduced which is equipped on a mass production motorcycle for the first time in the world. It has been researched and developed for a long time as an injury reduction technology for collision accidents. Honda automobile technology was used for the research and development of the motorcycle airbag, and many specific issues such as the analysis of the collision conditions particular to motorcycles have been solved to realize today- success. It might be known that ADAC in-house crash test held in August this year confirmed the high effectiveness of the airbag system and showed a positive result. This motorcycle airbag system is equipped to the Honda Gold Wing and launched in North America in August, 2006. Also in Europe, it will be sold by the end of this year. Each theme of Honda motorcycle safety technology can be seen at the Honda booth.
Auf der zweitägigen Fachtagung "Luftqualität an Straßen" wurden aktuelle Forschungsaktivitäten auf dem Gebiet der Luftreinhaltung und besonders der verkehrsbedingten Luftschadstoffe präsentiert. Der Tagungsband gibt die 17 Fachvorträge und die Übersicht der tagungsbegleitenden Posterausstellung wieder.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 13. Oktober 2006 in Baden-Baden das 6. Symposium "Sicher fahren in Europa". Die Fachvorträge befassten sich mit den Themenbereichen: Ansätze zu mehr Verkehrssicherheit, - Verbesserung der Fahrzeugsicherheit, - Besondere Zielgruppen. Die CD-ROM dokumentiert die Grußworte, die Referate und die Podiumsdiskussion.