Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (97) (entfernen)
Volltext vorhanden
- nein (97) (entfernen)
Schlagworte
- Test method (32)
- Prüfverfahren (29)
- Safety (29)
- Sicherheit (29)
- Impact test (veh) (26)
- Bewertung (25)
- Conference (25)
- Evaluation (assessment) (25)
- Fußgänger (25)
- Pedestrian (25)
Institut
- Abteilung Fahrzeugtechnik (97) (entfernen)
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
The EVERSAFE project addressed many safety issues for electric vehicles including the crash and post-crash safety. The project reviewed the market shares of full electric and hybrid vehicles, latest road traffic accident data involving severely damaged electric vehicles in Europe, and identified critical scenarios that may be particular for electric vehicles. Also, recent results from international research on the safety of electric vehicles were included in this paper such as results from performed experimental abuse cell and vehicle crash tests (incl. non-standardized tests with the Mitsubishi i-MiEV and the BMW i3), from discussions in the UN IG REESS and the GTR EVS as well as guidelines (handling procedures) for fire brigades from Germany, Sweden and the United States of America. Potential hazards that might arise from damaged electric vehicles after severe traffic accidents are an emerging issue for modern vehicles and were summarized from the perspective of different national approaches and discussed from the practical view of fire fighters. Recent rescue guidelines were reviewed and used as the basis for a newly developed rescue procedure. The paper gives recommendations in particular towards fire fighters, but also to vehicle manufacturers and first-aiders.
A reduction of around 48% of all road fatalities was achieved in Europe in the past years including a reduced number of fatalities with an older age. However, among all road fatalities, the proportion of elderly is steadily increasing. In an ageing society, the European (Horizon2020) project SENIORS aims to improve the safe mobility of older road users, who have different transportation habits compared to other age groups. To increase their level of safe mobility by determining appropriate requirements for vehicle safety systems, the characteristics of current road traffic collisions involving the elderly and the injuries that they sustain need to be understood in detail. Hereby, the paper focuses on their traffic participation as pedestrian, cyclist or passenger car occupant. Following a literature review, several national and international crash databases and hospital statistics have been analysed to determine the body regions most frequently and severely injured, specific injuries sustained and types of crashes involved, always comparing older road users (65 years and more) with mid-aged road users (25-64 years). The most important crash scenarios were highlighted. The data sources included European statistics from CARE, data on national level from Germany, Sweden, Italy, United Kingdom and Spain as well as in-depth crash information from GIDAS (Germany), RAIDS (UK), CIREN and NASS-CDS (US). In addition, familiar hospital data from Germany (TraumaRegister DGU-®), Italy (Italian Register of Acute Traumas) and UK hospital statistics (TARN) were included in the study to gain further insight into specific injury patterns. Comprehensive data analyses were performed showing injury patterns of older road users in crashes. When comparing with mid-aged road users, all databases showed that the thorax body region is of particularly high importance for the older car occupant with injury severities of AIS 2 or AIS 3+, whereas the body regions lower extremities, head and thorax need to be considered for the older pedestrians and cyclists. Besides these comparisons, the most frequent and severe top 5 injuries were highlighted per road user group. Further, the most important crash configurations were identified and injury risk functions are provided per age group and road user group. Although several databases have been analysed, the picture on the road safety situation of older road users in Europe was not complete, as only Western European data was available. The linkage between crash data and hospital data could only be made on a general level as their inclusion criteria were quite different.
Europe has benefited from a decreasing number of road traffic fatalities. However, the proportion of older road users increases steadily. In an ageing society, the SENIORS project aims to improve the safe mobility of older road users by determining appropriate requirements towards passive vehicle safety systems. Therefore, the characteristics of road traffic crashes involving the elderly people need to be understood. This paper focuses on car occupants and pedestrians or cyclists in crashes with modern passenger cars. Ten crash databases and four hospital statistics from Europe have been analysed to answer the questions on which body regions are most frequently and severely injured in the elderly, and specific injuries sustained by always comparing older (65 years and above) with midâ€aged road users (25â€64 years). It was found that the body region thorax is of particularly high importance for the older car occupant with injury severities of AIS2 or AIS3+, where as the lower extremities, head and the thorax need to be considered for older pedestrians and cyclists. Further, injury risk functions were provided. The hospital data analysis showed less difference between the age groups. The linkage between crash and hospital data could only be made on a general level as their inclusion criteria were quite different.
The presence and performance of Advanced Driver Assistance Systems (ADAS) has increased over last years. Systems available on the market address also conflicts with vulnerable road users (VRUs) such as pedestrians and cyclists. Within the European project PROSPECT (Horizon2020, funded by the EC) improved VRU ADAS systems are developed and tested. However, before determining systems" properties and starting testing, an up-to-date analysis of VRU crashes was needed in order to derive the most important Use Cases (detailed crash descriptions) the systems should address. Besides the identified Accident Scenarios (basic crash descriptions), this paper describes in short the method of deriving the Use Cases for car-to-cyclist crashes. Method Crashes involving one passenger car and one cyclist were investigated in several European crash databases looking for all injury severity levels (slight, severe and fatal). These data sources included European statistics from CARE, data on national level from Germany, Sweden and Hungary as well as detailed accident information from these three countries using GIDAS, the Volvo Cars Cyclist Accident database and Hungarian in-depth accident data, respectively. The most frequent accident scenarios were studied and Use Cases were derived considering the key aspects of these crash situations (e.g., view orientation of the cyclist and the car driver- manoeuvre intention) and thus, form an appropriate basis for the development of Test Scenarios. Results Latest information on car-to-cyclist crashes in Europe was compiled including details on the related crash configurations, driving directions, outcome in terms of injury severity, accident location, other environmental aspects and driver responsibilities. The majority of car-to-cyclist crashes occurred during daylight and in clear weather conditions. Car-to-cyclist crashes in which the vehicle was traveling straight and the cyclist is moving in line with the traffic were found to result in the greatest number of fatalities. Considering also slightly and seriously injured cyclists led to a different order of crash patterns according to the three considered European countries. Finally the paper introduced the Use Cases derived from the crash data analysis. A total of 29 Use Cases were derived considering the group of seriously or fatally injured cyclists and 35 Use Cases were derived considering the group of slightly, seriously or fatally injured cyclists. The highest ranked Use Case describes the collision between a car turning to the nearside and a cyclist riding on a bicycle lane against the usual driving direction. A unified European dataset on car-to-cyclist crash scenarios is not available as the data available in CARE is limited, hence national datasets had to be used for the study and further work will be required to extrapolate the results to a European level. Due to the large number of Use Cases, the paper shows only highest ranked ones.
The Intersection 2020 project was initiated to develop a test procedure for Automatic Emergency Braking systems in intersection car-to-car scenarios to be transferred to Euro NCAP. The project aims to address current road traffic accidents on European roads and therefore sets a priority of the identification of the most important car-to-car accidents and Use Cases. Taking into account technological and practical limitations, Test Scenarios are derived from the Use Cases in a later stage of the project. This paper presents parts of a larger study and provides an overview of common car-to-vehicle(at least four wheels) collision types at junctions in Europe and specifies seven Accident Scenarios from which the three scenarios “Straight Crossing Paths (SCP)”, “Left Turn Across Path – Opposite Direction Conflict (LTAP/OD)” and “Left Turn Across Path – Lateral Direction (LTAP/LD)” are most important due to their high relevance regarding severe car-to-car accidents. Technical details about crash parameters such as collision and initial speeds are delivered. The analysis work performed is input for the definition and selection of the Use Cases as well as for the project’s benefit estimation. The numbers of accidents and fatalities in accidents at intersections involving a passenger car were shown per intersection type. In both statistics, it was found that accidents at crossroads and T- or staggered junctions are of highest relevance, followed by roundabouts. Focusing on accidents at intersections between one passenger car and another road user shows that around one-third of all accidents and related fatalities could have been assigned to car-to-PTW accidents and one-fifth of all accidents and fatalities to car-to-car accidents. Regarding car-to-car accidents with at least serious injury outcome 38% out of 34,489 car-to-car accidents happened at intersections. These figures correspond to 18% of the fatalities (4,236 fatalities in total). Considering all intersection types, around half of all related accidents happened in urban environments whereas this number decreased to one-third of all fatalities. Further, the proportion of road fatalities per country occurring at intersections varies widely across the EU. Also, there are proportionately more fatalities in daylight or twilight conditions at junctions. Use Cases are supposed to be derived from Accident Scenarios and by adding detailed information for example about the road layout, right-of-way and the vehicle trajectories prior to the collision. Instead of applying cluster algorithms to the accident data, a pragmatic approach was finally preferred to create them. Note: Use Cases serve as an intermediate step between the Accident Scenarios and the Test Scenarios which describe the actual testing conditions. Finally, 74 Use Cases were identified. This large number indicates the complexity of intersection crashes due to the combination of several parameters.
Per definition, SAE Level 2 (L2) Systems perform both the lateral and longitudinal vehicle motion control with the expectation that the driver completes the Object and Event Detection and Response (OEDR). Since every system performs also parts of the OEDR itself and this amount of OEDR also varies between different L2 systems depending on the intended system design, it cannot be taken for granted that drivers automatically understand their roles and responsibilities in interaction with the system. Especially highly reliable L2 systems performing a greater amount of OEDR while at the same time requiring only little driver input over time can make it difficult for drivers to correctly identify their role and responsibility. Until now, neither application-oriented assessment methods nor design guidelines for OEDR related system design features taking safety of human-machine-interaction into account are available. The objective is therefore to deliver a standardized tool for the assessment of human-machine-interaction-related safety of vehicles with L2 systems currently available on the market. To evaluate the impact of different system design aspects on safety of human-machine-interaction and also to be able to differentiate between system designs, a holistic, standardized and application-oriented assessment procedure is proposed. The novel tablet-based assessment tool focuses not only on available standards and guidelines but measures also concrete user behaviour and user understanding in interaction with the L2 systems. The aim is to gain further insights which cannot be measured directly by simple checklist instruments. For preparation, based on international standards, literature reviews and expert consultations, a first checklistbased expert-evaluation for currently available vehicles with L2 systems was developed. These assessments are focusing on different sources of user information (e.g. user manual), human-machine-interface design as well as the prevention of unintended use by different driver monitoring techniques. The checklist-tool was developed in cooperation with experts of different EuroNCAP test laboratories and validated in a common expert workshop to gain high level of standardization and agreement. However, to assess safety of human-machine-interaction holistically beyond these rather explicit forms of information design criteria, also implicit forms of drivervehicle-communication via vehicle dynamics, functional behavior or reliability play an important role and should be taken into account. Therefore, the main and novel methodological aim is to consider also interaction related processes regarding user´s understanding of roles and responsibilities when applying automated driving functions as well as user´s awareness of automation modes or traffic situations in the modular tablet-based assessment tool.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
Schutz von schwächeren Verkehrsteilnehmern: kommende Anforderungen aus Gesetzgebung und Euro NCAP
(2017)
Systeme der aktiven Fahrzeugsicherheit, insbesondere Notbremsassistenzsysteme und automatische Notbremssysteme, haben in den letzten zwei Dekaden große technische Fortschritte gemacht, und das im Wesentlichen ohne "Druck" von Gesetzgeber oder unabhängigen Testorganisationen " diese können aber durch passende Anforderungen den Vormarsch der Systeme in die Breite und die Ausnutzung von ansonsten für den Hersteller vielleicht nicht wirtschaftlichen Potentialen unterstützen. Dieser Bericht hat das Ziel, einen Überblick über die kommenden Anforderungen an Schutzsysteme für schwächere Verkehrsteilnehmer zu geben und diese Anforderungen in den Kontext Euro NCAP (=welchen Einfluss haben diese Anforderungen auf die Gesamtbewertung?) sowie Gesetzgebung (schwächere Anforderungen, aber dafür ein Markteintrittskriterium) zu stellen: - Anforderungen und Testprozeduren für Notbremsassistenz Fahrradunfälle 2018 und 2020 in Euro NCAP; - Anforderungen und Testprozeduren für Notbremsassistenz bei Nachtunfällen mit Fußgängern in Euro NCAP 2018; - Anforderungen und Testprozeduren für Abbiegeassistenzsysteme zum Schutz von Radfahrern in Unfallsituationen mit rechtsabbiegenden Lkw innerhalb der Fahrzeugtypgenehmigung.
Euro NCAP will start to test pedestrian Automatic Emergency Braking Systems (AEB) from 2016 on. Test procedures for these tests had been developed by and discussed between the AsPeCSS project and other initiatives (e.g. the AEB group with Thatcham Research from the UK). This paper gives an overview on the development process from the AsPeCSS side, summarizes the current test and assessment procedures as of March 2015 and shows test and assessment results of five cars that had been tested by BASt for AsPeCSS and the respective manufacturer. The test and assessment methodology seems appropriate to rate the performance of different vehicles. The best test result - still one year ahead of the test implementation - is around 80%, while the worst rating result is around 10%. Other vehicles are between these boundaries.
PROSPECT (Proactive Safety for Pedestrians and Cyclists) is a collaborative research project involving most of the relevant partners from the automotive industry (including important active safety vehicle manufacturers and tier-1 suppliers) as well as academia and independent test labs, funded by the European Commission in the Horizon 2020 research program. PROSPECT's primary goal is the development of novel active safety functions, to be finally demonstrated to the public in three prototype vehicles. A sound benefit assessment of the prototype vehicle's functionality requires a broad testing methodology which goes beyond what has currently been used. Since PROSPECT functions are developed to prevent accidents in intersections, a key aspect of the test methodology is the reproduction of natural driving styles on the test track with driving robots. For this task, data from a real driving study with subjects in a suburb of Munich, Germany was used. Further data from Barcelona will be available soon. The data suggests that intersection crossing can be broken down into five phases, two phases with straight deceleration / acceleration, one phase with constant radius and speed turning, and two phases where the bend is imitated or ended. In these latter phases, drivers mostly combine lateral and longitudinal accelerations and drive what is called a clothoid, a curve with curvature proportional to distance travelled, in order to change lateral acceleration smoothly rather than abrupt. The data suggests that the main parameter of the clothoid, the ratio distance travelled to curvature, is mostly constant during the intersections. This parameter together with decelerations and speeds allows the generation of synthetic robot program files for a reproduction of natural driving styles using robots, allowing a much greater reproducibility than what is possible with human test drivers. First tests show that in principle it is possible to use the driving robots for vehicle control in that manner; a challenge currently is the control performance of the robot system in terms of speed control, but it is anticipated that this problem will be solved soon. Further elements of the PROSPECT test methodology are a standard intersection marking to be implemented on the test track which allows the efficient testing of all PROSPECT test cases, standard mobile and light obstruction elements for quick reproduction of obstructions of view, and a concept for tests in realistic surroundings. First tests using the PROSPECT test methodology will be conducted over the summer 2017, and final tests of the prototype vehicles developed within PROSPECT will be conducted in early 2018
Accidents between right turning trucks and straight driving cyclists often show massive consequences. Accident severity in terms of seriously or fatally injured cyclists that are involved is much higher than in accidents of other traffic participants in other situations. It seems clear that adding additional mirrors will very likely not improve the situation. At ESV 2015, a methodology to derive test procedures and first test cases as well as requirements for a driver assist system to address blind spot accidents has been presented. However, it was unclear if and how testing of these cases is feasible, to what extent characteristics of different truck concepts (e.g. articulated vehicles, rigid vehicles) influence the test conduction and outcome, and what tolerances should be selected for the different variables. This work is important for the acceptance of a draft regulation in the UN working group on general safety. In the meantime, three test series using a single tractor vehicle, a tractor-semitrailer combination and a rigid vehicle have been conducted. The test tools (e.g. surrogate devices) have been refined. A fully crashable, commercially available bicycle dummy has been tested. If used correct, this dummy does follow a straight line quite precisely and it does not cause any damage to the truck under test in case of accidental impact. The dummy specifications are freely available. During testing, the different vehicle categories resulted in different trajectories being driven. Articulated vehicle combinations did first execute a turn into the opposite direction, and on the other hand, single tractor vehicles did behave comparable to passenger cars. A possible solution to take these behaviors into account is to require the vehicles to drive through a corridor that is narrow for a precise straight-driving phase and extends during the turn. Other investigated parameters are the dummy and vehicle speed tolerances. The results from this research make it possible to draft a regulation for a driver assistance system that helps to avoid blind spot accidents: test cases have been refined, their feasibility has been checked, and corridors for the vehicles and for important parameters (e.g. test speeds) have been set. The test procedure is applicable to all types of heavy goods vehicles. In combination with the accidentology (ESV 2015 paper), the work provides the basis for a regulation for such an assistance system.
A methodology to derive precision requirements for automatic emergency braking (AEB) test procedures
(2015)
AEB Systems are becoming important to increase traffic safety. Test procedures in testing for consumer information, manufacturer self-certification and technical regulations are used to ensure a certain minimum performance of these systems. Consequently, test robustness, test efficiency and finally test cost become increasingly important. The key driver for testing effort and test costs is the required repeatable accuracy in a test design - the higher the accuracy, the higher effort and test costs. On the other hand, the performance of active safety systems depends on time discretization in the environment perception and other sub-systems: for instance, typical sensors supply information with a cycle time of 50 - 150 ms. Time discretization results in an inherent spread of system performance, even if the test conditions are perfectly equal. The proposed paper shows a methodology to derive requirements for a test setup (e.g. test repeats, use of driving robots, ...) as function of AEB system generation and rating method (e.g. Euro NCAP points awarded, pass/fail, ...). While the methodology itself is applicable to AEB pedestrian and AEB Car-Car scenarios, due to the lack of sufficient test data for AEB Car-Car, the focus of this paper is on AEB pedestrian scenarios. A simulation model for the performance of AEB Pedestrian systems allows for the systematic variation of the discretization time as well as test condition accuracy. This model is calibrated with test results of 4 production vehicles for AEB Pedestrian, all fully tested by BASt according to current Euro NCAP test protocols. Selected parameters to observe the accuracy of the test setup in case of pedestrian AEB is the calculated impact position of pedestrian on the vehicle front (as if no braking would have occurred), and the test vehicle speed accuracy. These variable was shown in real tests to be repeatable in the range of ± 5 cm and ± 0,25 km/h, respectively, with a fully robotized state of the art test setup. The sensitivity of AEB performance (measured in achieved speed reduction as well as overall rating result according to current Euro NCAP rating methods) towards discretization and the sensitivity of performance towards test accuracy then is compared to identify economic yet robust test concepts. These comparisons show that the available repeatability accuracy of current test setups is more than sufficient for today's AEB system capabilities. Time discretization problems dominate the performance spread especially in test scenarios with a limited pedestrian dummy reveal time (e.g. child behind obstruction, running adult scenarios with low car speeds). This would allow to increase test tolerances to decrease test cost. A methodology which allows to derive the required tolerances in active safety tests might be valuable especially for NCAPs of emerging countries that do not have the necessary equipment (e.g. driving robots, positioning units) available for the full-scale and high tolerance EuroNCAP active safety procedures yet still want to rate active safety systems, thus improving the global safety.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben. Das Ergebnis kann indes nicht zufriedenstellen. Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird im Beitrag, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der sich auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschrieben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen; dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschreiben. Das Ergebnis kann indes nicht zufriedenstellen: Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird hier, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschreiben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen. Dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
Neue Herausforderungen an die Unfallforschung durch Fahrerassistenz und automatisiertes Fahren
(2019)
Unfallrekonstruktion hat die Ableitung von Maßnahmen zur Minimierung der Unfallfolgen ermöglicht, vor allem durch Verbesserungen bei passiven Sicherheitseinrichtungen, aber auch durch die Verbesserung der Rettungskette, beispielsweise eCall. Heute können aktive Sicherheitssysteme die Unfallfolgen bereits vor der eigentlichen Kollision reduzieren oder durch Umfeldwahrnehmung und mittels Eingriff in die Fahrzeugsteuerung gegebenenfalls sogar vollständig verhindern. Funktionen, die aktiv in die Fahrzeugsteuerung eingreifen, lassen sich nach ihrer Wirkweise unterscheiden: zum einen handelt es sich um kontinuierlich automatisierende Funktionen, die meist länger aktiv bleiben (zum Beispiel ACC). Zum anderen um Funktionen, die in kritischen Fahrsituationen temporär in die Fahrzeugsteuerung eingreifen. Aufgezeigt wird, welche Konsequenzen und Risiken in Bezug auf diese Systeme sowie für bestimmte (zum Beispiel kritikale) Fahrsituationen anzunehmen sind. Zur Bewertung von aktiven Reglern, die in kritischen Fahrsituationen eingreifen, sind Unfalldaten nur noch eingeschränkt tauglich. Ähnliches gilt für die Bewertung von Ereignissen/ Zuständen im Rahmen kontinuierlicher Fahrzeugsteuerung, vor allem, wenn diese weiter vorausliegen. Wirkzusammenhänge automatisierter Fahrfunktionen müssen jedoch - gerade für den Mischverkehr mit konventionell gesteuerten Fahrzeugen - identifiziert werden. Dafür wird eine Szenariendatenbank mit relevanten Verkehrssituationen benötigt, in die Daten aus Naturalistic Driving Studies (NDS), aus Fahrversuchen oder Versuchen im Fahrsimulator eingehen können. Die zunehmende Durchdringung der Fahrzeugflotte mit kontinuierlich automatisierten Fahrfunktionen lässt eine Abnahme kritischer Fahrsituationen und eine Reduktion der Zahl der Verkehrsopfer erwarten. Allerdings verbleibt eine Restzahl an systemimmanenten Unfällen, die als unvermeidbar gelten müssen.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.
Within the automotive context camera monitor systems (CMS) can be used to present views of the traffic situation behind the vehicle to the driver via a monitor mounted inside the cabin. This offers the opportunity to replace classical outside rearview mirrors and therefore to implement new design concepts, aerodynamically optimized vehicle shapes and to reduce the width of the vehicle. Further, the use of a CMS offers the potential to implement functionalities like warnings or situation-adaptive fields of view that are not feasible with conventional rearview mirrors. Despite these potential advantages, it is important to consider the possible technical constraints of this technology and its effect on driver perception and behavior. On the technical side next to the field of view and die robustness of die system, aspects as its functionality at day and night as well as under varying weather conditions should be object to scientific investigation. Concerning human machine interaction, it has to be considered, that the perception of velocities and distances of approaching vehicles might be different for CMS as compared to conventional rearview mirrors and potential influences of factors as the Position of the displays or drivers' age should be taken into account. In order to shed light on these and further open issues, BASt is currently conducting a study that will cover the use of CMS under controlled conditions as well in real traffic. The first part of the study will focus on passenger cars, while in a second step the empirical investigation will be extended to heavy goods vehicles, where the potentials as well as the limitations of CMS might differ considerably. The presentation will cover the first part, with regard to the experimental design, implementation and initial results if already available.
This paper describes the methodology for the assessment of the socio-economic impact of SAFESPOT applications. The applications selected for the assessment cover vehicle to vehicle (v2v) as well as vehicle to infrastructure (v2i) communication systems. The applications address main problem areas of road safety: accidents at intersections, accidents due to hazardous road and weather conditions and accidents due to over speeding and inappropriate distance. The assessment methodology relies in its core on cost-benefit analysis (CBA) as the most widespread tool to assess the profitability of applications form the society point of view. The assessment is however not limited to CBA but also considers the economic effects for particular stakeholder groups such as users, public authorities and the like. Their individual cost and benefits can be investigated in stakeholder analyses. Both elements, CBA and stakeholder analysis, form an integrated assessment approach which is applied here. The assessment makes use of the sound methodological base which was provided by projects such as SEiSS and eIMPACT. Some characteristics of co-operative systems however call for special attention within the assessment. Most prominently, the assessment will concentrate on a bundle of applications. The impact of this bundle will be assessed under the conditions of different business and service models. These issues will be addressed in the paper. Moreover, this paper also provides insight in likely patterns of results and first results of socio-economic impact assessment itself.
During a lifecycle a tyre undergoes degradations due to mechanical wear and chemical ageing which affect not only durability and safety but also tyre/road noise emission and rolling resistance. This paper presents a study with the purpose to study how much tyre/road noise and rolling resistance change when car tyres are worn down from the original 8 mm tread depth to 2 mm, and when chemical ageing of the tyre rubber is simulated by exposure to heat. Six car tyres of different types were selected for the study which were worn on a wear machine in steps of 2 mm tread depth. Before, between and after these wear sessions tyre/road noise and rolling resistance were measured on two drum facilities with different surface textures, including replicas of ISO surfaces. Additionally, coast-by and CPX measurements were made on outdoor ISO test tracks. The results show that the wear and age effect was low on ISO surfaces but dramatic (noise increased with wear) on the rough-textured surface and high but opposite on an extremely smooth surface.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
When the EEVC proposed the full-scale side impact test procedure, it recommended that consideration should be given to an interior headform test in addition. This was to evaluate areas of contact not assessed by the dummy. EEVC Working Group 13 has been researching the parameters of a possible European headform test procedure in four phases. Earlier stages of the research have been presented at previous ESV conferences. The conclusions from these have suggested that the US free motion headform should be used in any European test procedure and that it should be a free flight test, not guided. This research has now culminated in proposals for a European test procedure. This paper presents the proposed EEVC side impact interior headform test procedure, giving the rationale for the test and the first results from the validation phase of the test protocol.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
In line with the new definition introduced by the European Commission (EC), the number of seriously injured road casualties in Germany for 2014 is assessed in this study. The number of MAIS3+ casualties is estimated by two different methodological approaches. The first approach is based on data from the German Inâ€Depth Accident Study (GIDAS), which is closely related to the German Road Traffic Accident Statistics. The second approach is based on data from the German TraumaRegister DGU-® (TRâ€DGU), which includes many more hospitals but not all MAIS3+ injuries.
Powered Two Wheelers (PTWs) accidents constitute one of the road safety problems in Europe. PTWs fatalities represent 22% at EU level in 2006, having increased during last years, representing an opposite trend compared to other road users" figures. In order to reduce these figures it is necessary to investigate the accident causation mechanisms from different points of view (e.g.: human factor, vehicle characteristics, influence of the environment, type of accident). SAFERIDER project ("Advanced telematics for enhancing the SAFEty and comfort of motorcycle RIDERs", under the European Commission "7th Framework Program") has investigated PTW accident mechanisms through literature review and statistical analyses of National and In-depth accident databases; detecting and describing all the possible PTW's accident configurations where the implementation of ADAS (Advanced Driver Assistance Systems) and IVIS (In-Vehicle Information Systems) could contribute to avoid an accident or mitigate its severity. DIANA, the Spanish in-depth database developed by CIDAUT, has been analyzed for that purpose. DIANA comprises of accident investigation teams, in close cooperation with police forces, medical services, forensic surgeons, garages and scrap yards. An important innovation is the fact that before injured people arrive to hospitals, photographs and explanations about the possible accident injury mechanisms are sent to the respective hospitals (via 3G GPRS technology). By this, additional information to medical staff can be provided in order to predict in advance possible internal injuries and select the best medical treatment. This methodology is presented in this paper. On the other hand, the main results (corresponding to road, rider and PTW characteristics; pre and post-accident manoeuvres; road layout; rider behaviour; impact points; accident causations;...) from the analyses of the PTW accidents used for SAFERIDER are shown. Only accident types relevant to ADAS and IVIS devices have been considered.
A means of assessing the passive safety of automobiles is a desirable instrument for legislative bodies, the automobile industry, and the consumer. As opposed to the dominating motor vehicle assessment criteria, such as engine power, spaciousness, aerodynamics and consumption, there are no clear and generally accepted criteria for assessing the passive safety of cars. The proposed method of assessment combines the results of experimental safety tests, carried out according to existing legally prescribed or currently discussed testing conditions, and a biomechanical validation of the loading values determined in the test. This evaluation is carried out with the aid of risk functions which are specified for individual parts of the body by correlating the results of accident analysis with those obtained by computer simulation. The degree of conformance to the respective protection criterion thus deduced is then weighted with factors which take into account the frequency of occurrence and the severity of the accident on the basis of resulting costs. Each of the test series includes at least two frontal and one lateral crash test against a deformable barrier. The computer-aided analysis and evaluation of the simulation results enables a vehicle-specific overall safety index as well as partial and individual safety values to be determined and plotted graphically. The passive safety provided by the respective vehicle under test can be defined for specific seating positions, special types of accident, or for individual endangered parts of the body.
The GRSP informal group on child restraint systems (CRS) finalised phase 1 of a new regulation for the homologation of CRS . This regulation is the subject of several discussions concerning the safety benefits and the advantages and disadvantages that certain specific points may bring. However, these discussions are sometimes not based on scientific facts and do not consider the whole package but only single items. Based on the experience of the CASPER partners in the fields of human behaviour, accident analysis, test procedures and biomechanics in the area of child safety, a consideration of the safety benefits of phase 1 of the new regulation and recommendations for phase 2 will be given.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
Thoracic injuries are one of the main causes of fatally and severely injured casualties in car crashes. Advances in restraint system technology and airbags may be needed to address this problem; however, the crash test dummies available today for studying these injuries have limitations that prevent them from being able to demonstrate the benefits of such innovations. THORAX-FP7 was a collaborative medium scale project under the European Seventh Framework. It focused on the mitigation and prevention of thoracic injuries through an improved understanding of the thoracic injury mechanisms and the implementation of this understanding in an updated design for the thorax-shoulder complex of the THOR dummy. The updated dummy should enable the design and evaluation of advanced restraint systems for a wide variety (gender, age and size) of car occupants. The hardware development involved five steps: 1) Identification of the dominant thoracic injury types from field data, 2) Specification of biomechanical requirements, 3) Identification of injury parameters and necessary instrumentation, 4) Dummy hardware development and 5) Evaluation of the demonstrator dummy. The activities resulted in the definition of new biofidelity and instrumentation requirements for an updated thorax-shoulder complex. Prototype versions were realised and implemented in three THOR dummies for biomechanical evaluation testing. This paper documents the hardware developments and biomechanical evaluation testing carried out.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
The European Enhanced Vehicle-safety Committee (EEVC) Working Group 13 for Side Impact Protection has been developing an Interior Headform Test Procedure to complement the full-scale Side Impact Test Procedure for Europe and for the proposed IHRA test procedures. In real world accidents interior head contacts with severe head injuries still occur, which are not always observed in standard side impact tests with dummies. Thus a means is needed to encourage further progress in head protection. At the 2003 ESV-Conference EEVC Working Group 13 reported the results on Interior Headform Testing. Further research has been performed since and the test procedure has been improved. This paper gives an overview of its latest status. The paper presents new aspects which are included in the latest test procedure and the research work leading to these enhancements. One topic of improvement is the definition of the Free Motion Headform (FMH) impactor alignment procedure to provide guidelines to minimize excessive headform chin contact and to minimize potential variability. Research activities have also been carried out on the definition of reasonable approach head angles to avoid unrealistic test conditions. Further considerations have been given to the evaluation of head airbags, their potential benefits and a means of ensuring protection for occupants regardless of seating position and sitting height. The paper presents the research activities that have been made since the last ESV Conference in 2003 and the final proposal of the EEVC Headform Test Procedure.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
In the paper it is investigated to what extend one can extrapolate the detailed accident database GIDAS (German In-Depth Accident Study), with survey area Hanover and Dresden region, to accident behavior in other regions and countries within Europe and how such an extrapolation can be implemented and evaluated. Moreover, it is explored what extent of accident data for the target country is necessary for such an extrapolation and what can be done in situations with sparse and low accident information in a target region. It will be shown that a direct transfer of GIDAS injury outcomes to other regions does not lead to satisfactory results. But based on GIDAS and using statistical decision tree methods, an extrapolation methodology will be presented which allows for an adequate prediction of the distribution of injury severity in severe traffic accidents for European countries. The method consists essentially of a separation of accidents into well-described subgroups of accidents within which the accident severity distribution does not vary much over different regions. In contrast the distribution over the various subgroups of accidents typically is rather different between GIDAS and the target. For the separation into the subgroups meaningful accident parameters (like accident type, traffic environment, type of road etc.) have been selected. The developed methodology is applied to GIDAS data for the years 1999-2012 and is evaluated with police accident data for Sweden (2002 to 2012) and the United Kingdom (2004 to 2010). It is obtained that the extrapolation proposal has good to very good predictive power in the category of severe traffic accidents. Moreover, it is shown that iterative proportional fitting enables the developed extrapolation method to lead to a satisfactory extrapolation of accident outcomes even to target regions with sparse accident information. As an important potential application of the developed methodology the a priori extrapolation of effects of (future) safety systems, the operation of which can only be well assessed on the basis of very detailed GIDAS accident data, is presented. Based on the evaluation of the presented extrapolation method it will be shown that GIDAS very well represents severe accidents, i.e. accidents with at least one severely or fatally injured person involved, for other countries in Europe. The developed extrapolation method reaches its limits in cases for which only very little accident information is available for the target region.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
Since integrated safety systems combine active and passive safety elements in one safety system, it is necessary to define new procedures to evaluate vehicle safety from the overall system point of view. The main goal of the ASSESS project is to develop harmonized and standardized assessment procedures for collision mitigation and avoidance systems. Methods and Data Sources: In ASSESS, procedures are developed for: driver behaviour evaluation, pre-crash system performance evaluation, crash performance evaluation, socio-economic assessment. This paper will concentrate on the activities related to the crash evaluation. The objective is to perform simulations, sled tests and crash tests in order tounderstand the influence of the activation of the pre-crash systems on the occupants" injuries during the crash phase. When a traffic accident is unavoidable, pre-crash systems work on various safety devices in order to improve the vehicle occupants" protection. Braking assistance and adaptive restraint systems are the main pre-crash systems whose effect on the occupants" protection will be described in this paper. Results: The results will be a description of the effect of the activation of the pre-crash systems on the crash phase. Additionally, a set of recommendations for future methodology developments will be delivered. Furthermore, a first approach to the study of the effect of the pre-crash systems activation on the occupants" protection when the impact is unavoidable will be presented. This effect will be quantified using the biomechanical values obtained from the simulation and testing activities and their related injury risks. Simulation and testing activities will consider the following scenarios: - No activation of any pre-crash system, - Activation of one or a combination of several pre-crash systems. In this way, differences in the results obtained from different scenarios will show the effect of each pre-crash system separately during the crash phase. Discussion and Limitations: The set of activities developed in this research project is limited by the fact that with the given resources only a limited number of vehicle models could be investigated. In addition, there are also limitations related to the injury risk curves and the passive safety tools currently on the market. Conclusion and Relevance to session submitted: The paper will present a complete analysis of the effect of pre-crash systems during the crash phase when the impact is unavoidable. Details, limitations and first application experience based on a few examples will be discussed. Currently, there is not any regulation, assessment program, or other similar official procedure able to assess pre-crash systems during the crash phase. This project comprises phases of traffic accidents which have been historically analysed separately, and aims to evaluate them taking into account their interrelationship. ASSESS is one of the first European projects which deals in depth with the concept of integrated safety, defining methodologies to analyse vehicle safety from a global point of view.
Airbags are, together with the three-point belt, the most effective passive safety equipment of vehicles. However, literature shows that sound pressure levels of up to 170 dB can occur during airbag deployment. A literature review revealed no systematic experimental data on possible hearing loss by airbag deployment, that also takes any other crash accompanied noise into account, such as deformation and impact noise. Also the rising number of airbags per vehicle resulting in a higher number of deployed airbags in an accident was not addressed with respect to hearing loss. Thus, an extensive test matrix of noise measurements during airbag deployments was conducted including onboard measuring during crashes and static measurements. Dynamic and static experiments with single and multiple airbag deployments were conducted. The results of this study show, that in the analyzed crash constellations the acoustic emission of the collision as well as the car deformation can trigger the stapedius reflex before the airbag deployment. The stapedius reflex protects the inner ear at least partially in case of dangerous sound levels. However, it seems that multiple airbag deployments in a short sequence pose a considerable risk for hearing impairments despite the fully contracted stapedius muscle. Further and in line with Price et al. (2013) it was found that the risk of hearing loss is lower with closed windows. The analysis of patient and accident data showed no link between airbag deployment and hearing loss. This might be caused by low case numbers of reported hearing loss problems up to now. In conclusion the results show that a singular analysis of the sound pressure of airbag deployments without crash accompanied noises is not sufficient as the protective effect of the stapedius reflex is neglected. Still, successive airbag deployments in a short timeframe raise the risk of hearing loss. Further investigation on hearing impairment due to airbag deployment and triggering of the stapedius reflex is needed and the data acquisition of accidents and patients should consider hearing loss aspects.
The development of tyre- and truck-manufacturers leads to the direction to introduce wide base single tyres (size 495/45R22,5) instead of twin tyres on the driving axle of trucks, tractors and busses. To study the driving behaviour and safety of various trucks and units with different tyre combinations and loading conditions was the aim of the study. A computer-aided simulation was used for this investigation. Drive tests with a 40 t unit with prototype single tyres on the drive axle were carried out to verify the simulation. Alterations in driving behaviour and driving safety are mainly dependent on the tyre cornering stiffness. The prototype wide single tyres had a higher lateral stiffness which leads to a higher degree of under-steering (safer driving behaviour). The altered spring base on the drive axle had no influence on the side- tilt stability of vehicle combinations but the solo truck profited from the higher rear axle roll stiffness (less danger for roll-over accidents). As far as the driving safety is concerned nothing speaks against wide base tyres on the drive axle. The simulation of a tyre defect in a bend (assuming 40% of the max. transferable side force for the flat tyre) showed no increased danger using wide single tyres. Later driving tests showed however the need of tyre run flat possibilities to avoid jack-knifing of road trains. Also tyre pressure monitoring systems and electronic stability programs for the trucks are advised.
The Swedish National Road Administration (SNRA), the Japanese Automobile Research Institute (JARI) and the Federal Highway Research Institute (BASt) are co-operating in the International Harmonized Research Activities on Intelligent Transportation Systems (IHRA-ITS). Under this umbrella a joint study was conducted. The overall objective of this study was to contribute to the definition and validation of a "battery of tools" which enables a prediction and an assessment of changes in driver workload due to the use of in-vehicle information systems (IVIS) while driving. In this sense \"validation\" means to produce empirical evidence from which it can be concluded that these methods reliably discriminate between IVIS which differ in terms of relevant features of the HMI-design. Additionally these methods should also be sensitive to the task demands imposed on the driver by the traffic situation and their interactions with HMI-design. To achieve these goals experimental validation studies (on-road and in the simulator) were performed in Sweden, Germany and Japan. As a common element these studies focused on the secondary task methodology as an approach to the study of driver workload. In a joint German-Swedish on-road study the Peripheral Detection Task (PDT) was assessed with respect to its sensitivity to the complexity of traffic situations and effects of different types of navigation systems. Results show that the PDT performance of both the German and the Swedish subjects reflects the task demands of the traffic situations better than those of the IVIS. However, alternative explanations are possible which will be examined by further analyses. Results of this study are supplemented by the Japanese study where informational demands induced by various traffic situations were analysed by using a simple arithmetic task as a secondary task. Results of this study show that relatively large task demands can be expected even from simple traffic situations.
Automated driving will provide many kinds of benefits - some direct and some indirect. The benefits originate at the individual level, from changes in the behaviour of drivers and travellers with regard to driving and mobility, ending up with benefits at the social level via changes in the whole transport system and society, where many of the current planning and operations paradigms are likely to be transformed by automated driving. There may also be disbenefits, particularly at a social level, for example in intensity of travel which could result in additional congestion and increased use of natural resources. There may also be unintended consequences. For example, we do not know the impacts on public transport: driverless vehicles could provide a means to a lower cost service provision, but the availability of automated cars could lead to more car travel at the expense of collective transport.