91 Fahrzeugkonstruktion
Today's volumes of traffic require more and more responsibility from each individual road user in their interactions. Those who drive motor vehicles have the singular obligation to minimise the risk of accidents and hence the severity of injuries, particularly with a view to the most vulnerable road users such as motor bikes, bikes and pedestrians. Since responsible and pro-active driving depends first and foremost on the visual information relayed by our eyes and the visual channel this requires good command of the traffic and all-round visibility from our driver's seat. Granted that human error can never be fully excluded, improving visibility around the car is nevertheless an urgent priority. To do so, we need to rate visibility in the most realistic driving situations. Since the existing visibility metrics and methodology are not applicable to real-life driving situations, this study aimed at developing a new visibility rating methodology based on real-life accident scenarios. On the basis of the cases documented by the accident research project, this study analysed criteria indicative of diminishing visibility on the one hand and revealing some peculiarities in connection with the visibility issue on the other. Based on the above, the project set out to develop a rating methodology allowing to assess all-round visibility in various road situations taking into account both driver and road geometries. In this context, the assessment of visibility while turning a corner, crossing an intersection and joining traffic on a major road (priority through route) is of major importance. The first tests have shown that critical situations can be avoided by adapting the relevant geometries and technical solutions and that significant improvements of road safety can be derived therefrom.
For the estimation of the benefit and effect of innovative Driver Assistance Systems (DAS) on the collision positions and by association on the accident severity, together with the economic benefit, it becomes necessary to simulate and evaluate a variety of virtual accidents with different start values (e.g. initial speed). Taken into account the effort necessary for a manual reconstruction, only an automated crash computation can be considered for this task. This paper explains the development of an automated crash computation based on GIDAS. The focus will be on the design of the virtual vehicle models, the method of the crash computation as well as exemplary applications of the automated crash computation. For the first time an automated crash computation of passenger car accidents has been realized. Using the automated crash computation different tasks within the field of vehicle safety can be elaborated. This includes, for example, the calculation of specific accident parameters (such as EES or delta-V) for various accident constellations and the estimation of the economic benefit of DAS using IRFs (Injury Risk Functions).
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
In 2014 the sixth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
EEVC Status report
(2001)
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
The objective was to develop and validate a crash trolley (reference vehicle) equipped with a compartment and a full restraint system for driver and front seat passenger which can be used in full scale crash testing. Furthermore, the crash trolley should have a suspension to show rotation and nick effects similar to real vehicles. Within the development phase the reference vehicle was build based on a European family car. Special attention was needed to provide appropriate strength to the trolley and its suspension. The reference vehicle is equipped with a restraint system consisting of airbags, pedals, seats, dashboard, and windscreen. On the front of the vehicle different crash barriers can be installed to provide miscellaneous deceleration pulses. For the validation phase a series of low and high speed crash tests with HIII dummies were conducted and compared with full scale tests. For the comparison deceleration pulse, dummy numbers and vehicle movement were analyzed. Validation tests with velocities up to 60 km/h showed promising results. The compartment and the suspension systems stayed stable. Rotation effects were comparable with full scale car crash tests. The airbags and seat belt system worked reasonable. The acceleration pulse compared to an Euro NCAP test had a similar characteristic but was in general slightly lower. After the successful validation the reference vehicle is already in use in different studies in the field of vehicle safety research at BASt.
Topics of the status report are: Road accidents in Germany " Socio-economic costs due to road traffic accidents in Germany " Vehicle population and road performance " Electromobility " Alternative power train technologies: market penetration and consequences. The following research subjects are presented: Safety of electric vehicles " Driving dynamics of electric propelled vehicles " New requirements for the periodic technical inspection of electric and hybrid vehicles " Forward looking safety systems " Periodic roadworthiness tests " Cooperative systems: integration of existing systems " Safety related traffic information " Urban space: User oriented assistance systems and network management " Automated driving " Study on camera-monitor-systems " Freight transport " BioRID TEG, dummy harmonization " Frontal impact and compatibility " Child safety " FlexPLI " GIDAS: a blueprint for worldwide in-depth road accident investigations " Druid: Driving under the influence of drugs, alcohol and medicines " Smoke and toxicity in bus fires.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Topics of this report are: Road accidents in Germany - Socio-economic costs due to road traffic accidents - Vehicle population and road performance " Automotive IT " Electromobility. The following research subjects are presented: Safety of electric vehicles - Forward looking safety systems - Cooperative systems - Safety related traffic information - Freight transport: Action plan freight transport and trial with longer trucks - Lane departure warning systems and Advanced emergency braking systems (AEBS) for heavy duty vehicles - Dummy harmonization " Compatibility - Child safety - Virtual testing - Driving under the influence of drugs, alcohol and medicines - Fire safety of buses - Milled shoulder rumble strips - Conspicuity of powered-two-wheelers - Automatically dipped high beam and rear view mirrors.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Technical progress in automotive engineering focuses at the moment on two competing branches: improving safety and reducing energy consumption. Recent consideration has been given to a third factor, cost to the consumer. Challenges are presented by demographic changes, especially with increasing participation of elderly people in road traffic. The report considers the recent history of road accidents in Germany and statistics relating to vehicle population and road performance. There is a general trend towards decreasing numbers of accidents and their severity. Transport is responsible for roughly 20% of CO2 emissions and approximately 70% of total petroleum consumption. The Federal Government has responded to these challenges by publishing the Freight Transport and Logistics Masterplan in the summer of 2008. It describes the strategic transport policy direction and the key elements of the future course of action which are to be used to ensure the provision of efficient infrastructure and, at the same time, to reduce the amount of energy consumed by vehicles and make transport more efficient, cleaner and quieter. This document contains a number of concrete measures subsumed under the following six objectives: Making optimum use of transport infrastructure - shaping transport to make it more efficient; Reducing the number of journeys - ensuring mobility; Transferring more traffic to the railways and inland waterways; Upgrading more transport arteries and hubs; Environmentally friendly, climate friendly, quiet and safe transport, and Good working conditions and good training in the freight transport industry. Progress in research is outlined in the following areas: Daytime Running Lights for Motorcycles; Safety of hydrogen vehicles - addressing safety and environmental issues by development of a Global Technical Regulation for hydrogen vehicles; Elements of active vehicle safety for elderly drivers; Periodical Technical Inspection of electronically controlled systems in road vehicles - Electronic Stability Control; Pedestrian protection; Crash Compatibility - role of collision partner in passive safety tests; Child safety; Euro NCAP - Child Restraint Systems, and German Field Operational Test on Car-to-Car and Car-to-Infrastructure Systems (SIM-TD). The research project AKTIV - "Adaptive and Cooperative Technologies for Intelligent Traffic" encompasses the design, development, and evaluation of novel driver assistance systems, knowledge and information technologies and is set up to find solutions for efficient traffic management and Car-to-Car and Car-to-Infrastructure communication for future cooperative vehicle applications. The European Statement of Principles on the Human Machine Interface (HMI), presented at the eSafety Conference, which was held in Berlin on 5/6 June 2007, addresses issues such as Real Time Traffic Information (RTTI), Legal issues of Advanced Driver Assistance Systems (ADAS) and e-security.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
Accident research 2.0: New methods for representative evaluation of integral safety in traffic
(2013)
BMW has developed a procedure for rating Advanced Driver Assistance Systems (ADAS) benefits that integrates two distinct tools. The tool "S.A.F.E.R." is designed to analyze the pre-crash phase. The aim of S.A.F.E.R. is to simulate all relevant processes in sufficient detail to obtain reproducible estimates of key indicators (effectiveness, false positives, etc.). The relevant processes include not only traffic and vehicle dynamics, but also environmental and most importantly human factors. Representative distributions of factors and parameters are obtained by taking the stochastic variation of all relevant parameters into account in the simulations. The second tool, known as "ICOS", has been designed to provide a high-resolution, high-fidelity description of crash phase dynamics. If one converts the outputs of stochastic simulation into inputs for crash dynamics, the result is a comprehensive description of exactly how a safety system can reduce injuries. Applications currently focus on high-fidelity simulation of individual crashes in order to enhance our understanding and optimization of connected safety systems. An integrated simulation process thus allows an exact prediction of the effectiveness in individual cases in terms of injury severity. The development and rating of integral safety need to reflect the true efficiency in the field. The integrated approach described here could provide a valid and reproducible basis for rating connected systems of active and passive safety. In particular, "virtual experiments" using a traffic-based approach and incorporating models of all relevant processes constitute an essential element of the approach.
The presentation deals with the simulation tool rateEFFECT which intends to answer the following questions: Which active safety systems should be developed to maximize safety benefit in real traffic accidents? What is the effectiveness of a specific active safety system in the real world? How many casualties could be avoided by such a system? It is shown that a lot of information is required to simulate existing accidents in order to estimate ADAS effects. This particularly includes numerical values for the pre-crash and in-crash phase. The database GIDAS provides a required minimum number of these parameters for a statistically significant sample.
The misuse of CRS (child restraint system) is one of the most urgent problems in connection of child safety in cars. Numerous field studies show that more than two thirds of all CRS are used in a wrong way. This misuse could lead to serious injuries for the children. Surprisingly the quality of CRS use is coded much better in accident data (e.g. GIDAS) than the results of observatory field studies show. It is expected that misuse of CRS was not detected by the accident teams in a large number of the cases. An essential part in improving child seats and their usability is the knowledge of the relation between misuse and resulting injuries. For that the analysis and experimental reconstruction of accidents is an important part. For allowing an exact experimental accident reconstruction, it is necessary to have detailed information about the securing situation of the child and about the installation of the CRS in the car.
Automotive interiors have long been a potentially injurious impact area to occupants during accidents, especially in the absence of adequate padding. The U.S. Federal Motor Vehicle Safety Standard (FMVSS) 201, Occupant Protection in Interior Impact, outlines test procedures and performance criteria in order to mitigate potentially injurious head impacts to interior surfaces. FMVSS 201 specifies a finite set of impact locations and applies to passenger vehicles of a specified year range and with a gross vehicle weight rating less than 10,000 lb. In this paper, two head impact test methodologies are presented, a pendulum-test device and a Free Motion Headform (FMH) launching device, which allows for dynamic, repeatable impact evaluation of various vehicle interior surfaces and their impact attenuation abilities. The presented testing includes multiple series that evaluate the effect of differing vehicle upper interior padding on occupant head injury. One study in particular, analyzes a head impact to the side header of a heavy truck (not included in FMVSS 201) during a 90 degree rollover. Additionally, two other series of tests are presented which assess the injury reduction effect of side airbags to near side as well as far side occupants in a side impact scenario. Lastly, a forensic analysis is presented which evaluates two possible head impact locations experienced in a real world accident by analysis of the resulting interior compartment damage utilizing the FMH launching device test method. The data collected and presented includes accelerometer instrumentation and high speed video analysis. These studies demonstrate that adequate padding and airbags are very effective at mitigating head injury potential at impact speeds of 12-25 mph (19-40 kph).
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
The European CASPER (Child Advanced Safety Project for European Roads) project studying car child safety includes a sociological approach in order to have a better understanding of the behaviour of parents driving children under 12 years old. A questionnaire was distributed via the internet in Europe with 998 parents (representing 1638 children) from 22 European countries responding. The results inform on the way parents secure their children during a car trip. Many parents did not control how their children were installed in the child restraint system (CRS). A toddler was more likely to travel into a child seat than an older child was. Regarding misuse situations, an important part of the participants did not think that they could make mistakes when fixing the child seat to the car (26%) or when placing the child into the seat (39%). This leaves an important field of action especially by communication via different media and in the CRS sale outlets.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
In 2012 the fifth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Die EU hat für die Verkehrssicherheit in Europa ein anspruchsvolles Ziel vorgegeben: Bis 2010 soll die Anzahl der im Straßenverkehr Getöteten gegenüber 2000 halbiert werden. Für Deutschland kann eine erfolgreiche Zwischenbilanz gezogen werden: In den letzten 5 Jahren nahm trotz Vergrößerung des Kraftfahrzeugbestandes um 6% die Anzahl der Verkehrstoten um 29% ab, in den vergangenen 10 Jahren ist ein Rückgang um 43% zu verzeichnen. Diese im internationalen Vergleich überdurchschnittlichen Erfolge sind nicht zuletzt auch auf Fortschritte in der Fahrzeugtechnik zurückzuführen, wobei die zunehmende Verbreitung von Systemen der Aktiven Sicherheit wie ABS, BAS, ESP einen entscheidenden Anteil hat. Nach der deutlichen Reduzierung von Fahrunfällen durch ESP-® stehen nun die Auffahrunfälle im Fokus der Sicherheitsentwicklung von Mercedes-Benz. Das Paket aus verbessertem rückwärtigen Signalbild (Adaptives Bremslicht) und Brems-Assistent (BAS) wurde kürzlich durch radarbasierte Bremsassistenz ergänzt (BAS PLUS und PRE-SAFE-®-Bremse). Der Beitrag geht auf Funktion und Wirksamkeit der einzelnen Systeme ein und gibt einen Ausblick in die nähere Zukunft.
Motorcycle safety research
(2007)
Honda- global motorcycle sales exceeded the 10 million units mark since 2004, and further expansion is expected. As a responsibility for a company to provide mobility, Honda is focusing on motorcycle safety as top priority and has been working on various activities for both aspects of hardware and software. Here, we present Honda- activity for the safety technology of motorcycles. At present, Honda is promoting motorcycle safety in the four themes of prevention and collision safety such as safety education, recognition assistance, accident prevention and injury reduction. First, in the area of the safety education, the "Honda Safety Driving Promotion Center" was established in 1970, and motorcycle riders and vehicle driver trainings have been organized, and the traffic training centers are used as an actual practice field not only in Japan but also in many other regions in the world. Through our training activities, the new area of safety training with hardware assistance was developed and Honda- unique technology was accumulated such as the riding simulator which can provide experience of potentially dangerous situations without risk. Especially, the "riding trainer", the popular version of the riding simulator, was introduced at several motor shows in various countries and launched in September 2005. It was distributed first in Europe and is expected to expand globally aiming at 3000 units worldwide.. And in Europe, the newest version, which includes the suburban roads program, jointly developed with ADAC, will be released in near future. In the area of recognition assistance, "vehicle to vehicle communication technology" is under development using the advantage of being a manufacturer of both motorcycles and cars. This technology is under research as Honda "ASV-3" in Japan, and as part of C2C activity in Europe. As for the accident prevention, advanced brake systems for motorcycles to assist more effective brake operation have been expanded, Honda signed the European Road Safety Charter in April 2004 with the advanced brake systems commitment and furthermore, they are expanding according to vehicle characteristics and region. Then all models above 250 cc will have a version of the system by 2010. And as the last theme, "motorcycle airbag system" is introduced which is equipped on a mass production motorcycle for the first time in the world. It has been researched and developed for a long time as an injury reduction technology for collision accidents. Honda automobile technology was used for the research and development of the motorcycle airbag, and many specific issues such as the analysis of the collision conditions particular to motorcycles have been solved to realize today- success. It might be known that ADAC in-house crash test held in August this year confirmed the high effectiveness of the airbag system and showed a positive result. This motorcycle airbag system is equipped to the Honda Gold Wing and launched in North America in August, 2006. Also in Europe, it will be sold by the end of this year. Each theme of Honda motorcycle safety technology can be seen at the Honda booth.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 13. Oktober 2006 in Baden-Baden das 6. Symposium "Sicher fahren in Europa". Die Fachvorträge befassten sich mit den Themenbereichen: Ansätze zu mehr Verkehrssicherheit, - Verbesserung der Fahrzeugsicherheit, - Besondere Zielgruppen. Die CD-ROM dokumentiert die Grußworte, die Referate und die Podiumsdiskussion.
The overall purpose of the ASSESS project is to develop a relevant and standardised set of test and assessment methods and associated tools for integrated vehicle safety systems, primarily focussing on currently available pre-crash sensing systems. The first stage of the project was to define casualty relevant accident scenarios so that the test scenarios will be developed based on accident scenarios which currently result in the greatest injury outcome, measured by a combination of casualty severity and casualty frequency. The first analysis stage was completed using data from a range of accident databases, including those which were nationally representative (STATS19, UK and STRADA, SE) and in-depth sources which provided more detailed parameters to characterise the accident scenarios (GIDAS, DE and OTS, UK). A common analysis method was developed in order to compare the data from these different sources, and while the data sets were not completely compatible, the majority of the data was aligned in such a way that allowed a useful comparison to be made. As the ASSESS project focuses on pre-crash sensing systems fitted to passenger cars, the data selected for the analysis was "injury accidents which involved at least one passenger car". The accident data analysis yielded the following ranked list of most relevant accident scenarios: Rank Accident scenario 1 Driving accident - single vehicle loss of control 2 Accidents in longitudinal traffic (same and opposite directions) 3 Accidents with turning vehicle(s) or crossing paths in junctions 4 Accidents involving pedestrians The ranked list highlights the relatively large role played by "accidents in longitudinal traffic", and "accidents with turning vehicle(s) or crossing paths in junctions" (the second and third most prevalent accident scenarios, respectively). The pre-crash systems addressed in ASSESS propose to yield beneficial safety outcomes with specific regard to these accident scenarios. This indicates that the ASSESS project is highly relevant to the current casualty crash problem. In the second stage of the analysis a selection of these accident scenarios were analysed further to define the accident parameters at a more detailed level .This paper describes the analysis approach and results from the first analysis stage.
This work aims at bringing evidence for mass incompatibility in frontal impact for cars built according to the UNECE R94 regulation. French national injury accidents database census for years 2005 to 2008 were used for the analysis. The heterogeneity of frontal self-protection among cars of different masses is investigated, as well as the partner protection parameter offered by these cars. The last part of the analysis deals with the estimation of the benefit, in terms of fatal and severe injuries avoided, if crashworthiness was harmonized for the whole fleet of vehicle. This calculation is done for France and is extended to all Europe.
An analysis of NASS and FARS was conducted to determine crash conditions that involved injuries that are not currently being directly addressed by vehicle safety standards or by consumer information test protocols. Analysis of both field data and US NCAP tests were conducted to determine the relative safety provided by seating position and by vehicle model year. Opportunities for improvements were determined by crash categories with large populations of injuries that were not addressed by safety tests or smaller numbers that were increasing in frequency. Areas of opportunities include improved occupant restrain in rollovers, improved frontal protection for rear seat occupants and improved fire prevention in frontal and rollover crashes.
The share of high-tensile steel in car bodies has increased over the last years. While occupant safety has generally benefited from this measure, there is a potential risk that, as a result, rescue time may increase considerably. In more than 60% of all car occupant fatalities a technical rescue has been necessary. These are in particular those cases where occupants die immediately at the accident scene. Therefore, in these cases "rescue time" is a very sensitive parameter. In addition to the general analysis of the need of technical rescue and the actual rescue time depending on model years, the injury pattern of occupants requiring technical rescue will be analysed to provide advice for rescue teams. Furthermore, a detailed analysis of rescue measures for the most popular car models depending on the safety cell design is given.
The paper presents a methodology for the benefit estimation of several secondary safety systems for pedestrians, using the exceptional data depth of GIDAS. A total of 667 frontal pedestrian accidents up to 40kph and more than 500 AIS2+ injuries have been considered. In addition to the severity, affected body region, exact impact point on the vehicle, and the causing part of every injury, the related Euro NCAP test zone was determined. One results of the study is a detailed impact distribution for AIS2+ injuries across the vehicle front. It can be stated, how often a test zone or vehicle part is hit by pedestrians in frontal accidents and which role the ground impact plays. Basing on that, different secondary safety measures can be evaluated by an injury shift method concerning their real world effectiveness. As an example, measures concerning the Euro NCAP pedestrian rating tests have been evaluated. It was analysed which Euro NCAP test zones are the most effective ones. In addition, real test results have been evaluated. Using the presented methodology, other secondary safety like the active bonnet (pop-up bonnet) or a pedestrian airbag measures can be evaluated.
Qualität von on-trip Verkehrsinformationen im Straßenverkehr : BASt-Kolloquium 23. und 24.03.2011
(2011)
Am 23. und 24. März 2011 veranstaltete die Bundesanstalt fuer Straßenwesen ein, um die Ergebnisse der erwähnten Projekte und Initiativen präsentieren zu lassen und mit anderen Experten zu diskutieren. Der vorliegende Tagungsband fasst die Ergebnisse des Kolloquiums zur "Qualität von on-trip Verkehrsinformationen" zusammen. Die Bereitstellung von Verkehrsinformationen ist geprägt von vielen Akteuren. Die Wertschöpfungskette beginnt bei der Sammlung grundlegender Verkehrsdaten zur Erstellung von Verkehrsinformationen und setzt sich mit der Datenverarbeitung und -interpretation bis hin zur Meldungserstellung fort. Die Weitergabe kann über verschiedene Übertragungsmedien erfolgen und beim Nutzer (z.B. im Navigationsgerät) empfangen werden. Jeder einzelne Schritt der Wertschoepfungskette kann sowohl von unterschiedlichen Partnern (privat oder öffentlich) übernommen werden als auch in der Hand eines Partners liegen. Diese Komplexität der Zusammenarbeit spiegelt sich demzufolge auch in Qualitätsmanagementprozessen wider. Im Rahmen des Kolloquiums wurden zwei wesentliche Qualitätsaspekte näher betrachtet: - die Datenqualität mit dem Focus auf Aktualitaet, Stimmigkeit der Daten verglichen mit einer gemessenen Realitaet sowohl zu Beginn der Wertschöpfungskette als auch an jeglichen Schnittstellen, - die Prozessqualität, welche sich insbesondere mit der reibungslosen Datenübergabe an den Schnittstellen der Wertschoepfungskette beschäftigt. Beide Qualitätsaspekte helfen zu verstehen, worin die heutigen Qualitätsprobleme bestehen und welche Massnahmen im Einzelnen ergriffen werden müssten, um eine nachhaltige Verbesserung zu erreichen. Einerseits kann es vorkommen, dass die Information über ein Verkehrsereignis an einer oder mehreren Stellen der Wertschöpfungskette korrekt vorliegt, jedoch durch ungenuegende technische oder organisatorische Schnittstellen im Prozessablauf wieder verloren geht und dem Nutzer folglich nicht zur Verfügung steht. Prominentes Beispiel eines solchen Problems in der Prozessqualität ist die fehlerhafte Interpretation der Meldung im Navigationsgerät, denkbar sind solche Informationsverluste jedoch an jeder Stelle der Wertschoepfungskette. Eine wichtige Massnahme zur Verbesserung der Prozessqualität ist die Standardisierung sowie die Überprüfung, ob die definierten Standards an jeder Stelle der Wertschöpfungskette eingehalten werden. Andererseits kann es vorkommen, dass die Datenqualität in Bezug auf ihre Genauigkeit von Anfang an so schlecht ist, dass der Nutzer eine fehlerhafte oder gar keine Nachricht übermittelt bekommt. Beispiel hierfür ist die Vielzahl von Stauereignissen, die entweder nicht gesendet wurden oder gesendet wurden, obwohl sie nicht vorhanden waren. Eine wichtige Massnahme zur Verbesserung dieser Situation ist die Verbesserung der Ereignisdetektion. Der Tagungsband enthaelt Präsentationen, die den Status Quo analysieren, Methoden zur verbesserten Datenerfassung vorschlagen und Möglichkeiten zur Verbesserung von Daten- und Prozessqualität vorstellen. Offen geblieben sind darüber hinaus folgende Fragestellungen: - Wie kann die Prozessqualität der gesamten Wertschöpfungskette bei der Vielzahl der Partner kontrolliert werden? Wer überwacht die Wertschöpfungskette? Wird hierfuer überhaupt eine zentrale Stelle benötigt? Oder ist es ausreichend, wenn jeder Partner eine angemessene Eingangs bzw. Ausgangskontrolle durchführt? - Obwohl es nur eine Realität gibt, entsteht doch Wettbewerb über die (Qualität der) Information zu dieser Realität. Wie kann Konsistenz zwischen allen Anbietern von sicherheitsrelevanten Informationen erreicht werden? Wo sollte der Wettbewerb enden und wie kann dies technisch, organisatorisch und wirtschaftlich realisiert werden? - Welche Prozesse sollten geschaffen werden, um Partner zu integrieren, die sich nicht an geschaffene Qualitätsstandards halten (z.B. kommerzielle Diensteanbieter, die nicht mit der Verkehrsinformationsszene vernetzt sind)? - Und nicht zuletzt, wie kann die Wahrnehmung des Nutzers über verschiedene Qualitätslevel unterschiedlicher Produkte verbessert werden? Ist der Nutzer in der Lage, die unterschiedlichen Qualitätsstufen von Verkehrssystemen zu unterscheiden? Falls nicht, welche Art von Unterstuetzung braucht der Kunde? Ein "European Information Services Assessment Programme" vergleichbar zu Euro NCAP für Fahrzeuge? Die Ergebnisse des Kolloquiums sollen die laufende Diskussion um die Verbesserung der Qualität von Verkehrsinformationen unterstützen.
Providing effective occupant protection in rollover crashes requires supplying the occupant with a restraint system proven effective in the dynamic rollover accident mode. Preventing ejection and providing restraint sufficient to prevent potentially injurious contacts with both interior and exterior vehicle components is paramount for effective rollover occupant protection. Research has shown that the injury potential can be decreased by closely coupling the occupant to the seat. This paper focuses on the effect of restraint system slack and its relationship to occupant excursion and ejection potential during rollover. Various restraint system configurations are evaluated in rollover-type test environments. A review of prior research is presented prior to presenting new quasi-static vehicle inversion studies conducted with live surrogate occupants. Additionally, dynamic rollover testing utilizing anthropometric test devices (ATDs) is presented. The influence of belt looseness and effects of various restraint designs on the belted occupants' injury potential are discussed.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
Accident data shows that the vast majority of pedestrian accidents involve a passenger car. A refined method for estimating the potential effectiveness of a technology designed to support the car driver in mitigating or avoiding pedestrian accidents is presented. The basis of the benefit prediction method consists of accident scenario information for pedestrian-passenger car accidents from GIDAS, including vehicle and pedestrian velocities. These real world pedestrian accidents were first reconstructed and the system effectiveness was determined by comparing injury outcome with and without the functionality enabled for each accident. The predictions from Volvo Cars" general Benefit Estimation Model are refined by including the actual system algorithm and sensing models for a relevant car in the simulation environment. The feasibility of the method is proven by a case study on a authentic technology; the Auto Brake functionality in Collision Warning with Full Auto Brake and Pedestrian Detection (CWAB-PD). Assuming the system is adopted by all vehicles, the Case Study indicates a 24% reduction in pedestrian fatalities for crashes where the pedestrians were struck by the front of a passenger car.
An eCall device has been mounted on some vehicles in France since 2003. It is an integrated car radio/GSM/GPS system that can be used with a SIM card. When an accident occurs, a call can be sent manually or automatically made to a telephone call centre. Knowing the geographic location, the vehicle identity and the possibility of a direct communication with the people involved enables the nearest emergency services to be called out. In this context, the LAB / CEESAR have set up a study aimed at evaluating the effectiveness of this system. The purpose of this paper is to detail the E-call system evaluation method of effectiveness used and give a global synthesis of the results.