Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (72) (entfernen)
Schlagworte
- Vehicle (72) (entfernen)
Institut
Technische Sicherheitsverbesserungen führen im Mensch-Maschine-System Straßenverkehr nicht zwangsläufig zu Sicherheitsgewinnen. Von den Einstellungen und Verhaltensgewohnheiten der Fahrzeugführer hängt es ab, ob vergrößerte sicherheitspotenziale adäquat genutzt oder durch Verhaltensanpassungen wieder verspielt werden. Anhand ausgewählter theoretischer Modelle und empirischer Forschungsergebnisse (OECD-Studie Behavioural adaptations to changes in the road transport system) wird dies diskutiert, und es werden Kriterien zur Vermeidung unerwünschter Adaptationen abgeleitet, die bereits bei der Planung und Realisierung technischer Verbesserungen Berücksichtigung finden sollten.
Internationale Aktivitäten der Forschung auf dem Gebiet "Passive Sicherheit von Kraftfahrzeugen"
(2000)
Eine Fülle von Aktivitäten ist derzeit auf den Gebieten Frontal- und Seitenstoß zu beobachten, die in Europa auf den beiden entsprechenden EG-Richtlinien aufbauen. Das EEVC führt seine Arbeiten, an denen die Automobilindustrie beteiligt ist, fort; hier sind insbesondere die Arbeiten zum Seitenstoß (Kopfaufprall und Barrierenvergleich) zu nennen. Auf weltweiter Ebene beginnen die Arbeiten der IHRA (International Harmonised Research Activities) in ein konkretes Stadium der Zusammenarbeit einzutreten. Auf dem Gebiet der Seitenkollision ist längerfristig ein neues Testverfahren geplant, in das der von ISO entwickelte WORLD-SID einbezogen werden soll. Es gibt derzeit viele ernsthafte Bemühungen der Forschung um Harmonisierung. Auch wenn es nicht zu einer weltweiten Harmonisierung kompletter Regelungen kommt, so gibt es doch Hoffnung auf eine weltweite Harmonisierung von definierten Teilbestimmungen in speziellen Regelungen, so zum Beispiel bezüglich der Testmethode, der Versuchspuppen und der Bewertung der Schutzkriterien. Der Name des EEVC, European Enhanced Vehicle-safety Committee, steht für die Weiterentwicklung der Fahrzeugsicherheit. Die beteiligten Regierungen sind überzeugt, dass moderne Technologien neue Möglichkeiten eröffnen, um die Sicherheit der Kraftfahrzeuge weiter zu verbessern.
Um die Automobilhersteller zu animieren, mehr als die gesetzlich geforderte Sicherheit anzubieten, haben strengere Versuche im Rahmen des Verbraucherschutzes in den letzten Jahren nicht nur in den USA, sondern auch in Europa deutlich an Bedeutung zugenommen. Besonders Initiativen aus England ist es zu verdanken, dass sich heute die Testverfahren nach dem sogenannten Euro NCAP, dem European New Car Assessment Programme, durchgesetzt haben. Diese Entwicklung wurde auch von der Europäischen Kommission unterstützt. Ziel des Euro NCAP ist es, die unabhängige und objektive Bewertung des Sicherheitsniveaus von Fahrzeugen zu einer transparenten und leicht verständlichen Verbraucherberatung zu fördern. Weiterhin sollen objektive Bewertungsverfahren entwickelt werden, um die Fahrzeughersteller zu ermutigen, die Fahrzeuge sicherer zu machen. Im Beitrag wird auf die Struktur des Euro NCAP sowie auf seine Arbeitsweise eingegangen. Vorgestellt werden ferner bisherige Testphasen mit Fahrzeugen deutscher Hersteller oder Tochtergesellschaften sowie deren Bewertung.
Die Anzahl von Informationsdisplays in Fahrzeugen nimmt ständig zu. Neben vielen positiven Aspekten gibt dieser Trend auch Anlass zur Befürchtung, dass die Aufmerksamkeit des Fahrers zu stark in Anspruch genommen und er von der eigentlichen Fahraufgabe abgelenkt wird. Um Sicherheitsrisiken zu vermeiden, ist eine unverzichtbare Auflage an solche Informationsdarstellungen, dass sie schnelle und sichere Informationsaufnahme sowie -verarbeitung gewährleisten und den Fahrer so gering wie möglich beanspruchen. Eine kritische Variable zur Bewertung stellt somit die Zeit dar, die benötigt wird, um solche Darstellungen richtig ablesen zu können. Die Okklusionsmethode bietet die Möglichkeit, sowohl die Geschwindigkeit der Informationsverarbeitung als auch deren Genauigkeit zu erfassen. Es wird entweder die Zeit gemessen, wie lange die Informationsdarstellungen betrachtet werden, oder es wird die Genauigkeit der Ablesung in Abhängigkeit von der Darbietungsdauer der Darstellung ermittelt. In einer Serie von 5 Experimenten wurde das Okklusionsverfahren als Bewertungsinstrument für das Design von einfachen Displays evaluiert. Die durchgeführten Experimente werden im Beitrag vorgestellt. Zusammenfassend stellt sich die Okklusionsmethode als geeignetes Instrument zur Bewertung von Informationsdarstellungen dar, da sie sowohl bei vorgegebenen Präsentationszeiten als auch bei selbstgewählten Betrachtungszeiten zwischen unterschiedlich komplexen Darstellungen zu trennen vermag. Zudem weisen die Ergebnisse darauf hin, dass die Okklusionsmethode auch geeignet ist, um Informationsdarstellungen zu trennen, welche die Wiederaufnahme einer Aufgabe nach einer Unterbrechung unterschiedlich schwer gestalten.
Es wird über ein verbessertes Rückhaltesystem für Rollstuhlfahrer berichtet, die in Behindertentransportwagen befördert werden. Es besteht aus zwei Einzelsystemen, dem Personenrückhaltesystem und dem Rollstuhlrückhaltesystem. Basierend auf Ergebnissen von Aufprallversuchen mit handelsüblichen Rückhaltesystemen konnte ein Adaptersystem entwickelt werden, das der Aufnahme der Gurtbefestigungen für den Dreipunktgurt des Personenrückhaltesystems und der Befestigungen der Gurtzungen für die hinteren Rollstuhlabspannungen dient. Aufgrund eines gemeinsamen Befestigungspunktes wird gewährleistet, dass Rollstuhl- und Personenrückhaltesystem kombiniert wirken. Besonders im Becken- und Schulterbereich wird ein korrekter Gurtverlauf erreicht. Derzeit wird die DIN 75078 (Behindertentransportwagen) Teil 2 von der Bundesanstalt für Straßenwesen mit dem Ziel überarbeitet, das Rückhaltesystem zur Sicherung von Rollstuhlnutzern zu beschreiben.
Since the beginning of the testing activities related to passive pedestrian safety, the width of the test area being assessed regarding its protection level for the lower extremities of vulnerable road users has been determined by geometrical measurements at the outer contour of the vehicle. During the past years, the trend of a decreased width of the lower extremity test and assessment area realized by special features of the outer vehicle frontend design could be observed. This study discusses different possibilities for counteracting this development and thus finding a robust definition for this area including all structures with high injury risk for the lower extremities of vulnerable road users in the event of a collision with a motor vehicle. While Euro NCAP is addressing the described problem by defining a test area under consideration of the stiff structures underneath the bumper fascia, a detailed study was carried out on behalf of the European Commission, aiming at a robust, worldwide harmonized definition of the bumper test area for legislation, taking into account the specific requirements of different certification procedures of the contracting parties of the UN/ECE agreements from 1958 and 1998. This paper details the work undertaken by BASt, also serving as a contribution to the TF-BTA of the UN/ECE GRSP, towards a harmonized test area in order to better protect the lower extremities of vulnerable road users. The German In-Depth Accident Database GIDAS is studied with respect to the potential benefit of a revised test area. Several practical options are discussed and applied to actual vehicles, investigating the differences and possible effects. Tests are carried out and the results studied in detail. Finally, a proposal for a feasible definition is given and a suggestion is made for solving possible open issues at angled surfaces due to rotation of the impactor. The study shows that, in principle, there is a need for the entire vehicle width being assessed with regard to the protection potential for lower extremities of vulnerable road users. It gives evidence on the necessity for a robust definition of the lower extremity test area including stiff and thus injurious structures at the vehicle frontend, especially underneath the bumper fascia. The legal definition of the lower extremity test area will shortly be almost harmonized with the robust Euro NCAP requirements, as already endorsed by GRSP, taking into account injurious structures and thus contributing to the enhanced protection of vulnerable road users. After finalization of the development of a torso mass for the flexible pedestrian legform impactor (FlexPLI) it is recommended to consider again the additional benefit of assessing the entire vehicle width.
Frontal impact is still the most relevant impact direction in terms of injury causation amongst car occupants. Especially for car-to-car frontal impacts the mass ratio between the involved vehicles has a significant impact on the injury risk (the heavier the opponent car the higher the injury risk). In order to address this issue frontal Mobile Deformable Barrier test procedures have been developed world-wide (for example the MPDB procedure that was fully described during the FIMCAR Project). The objective of this study was to investigate how vehicles of different weight classes perform in a mobile barrier test procedure compared to a fixed barrier test procedure (the full width rigid and offset deformable barrier test). Beyond that, the influence of vehicle mass and vehicle deformation on injuries was evaluated based on real world accident data. Five vehicle types were selected and tested in a fixed offset test procedure (ODB), a full width rigid barrier test procedure (FWRB) and a mobile offset test procedure (MPDB). For the accident analyses data from the German In-Depth Accident Study (GIDAS) was evaluated with a focus on MAIS 2+ injured belted front row car (UN-R 94 compliant cars) occupants in frontal impact accidents. Test data indicates higher dummy loadings, in particular for the head acceleration and chest acceleration, in the MPDB test for the vehicles with a mass lighter than the trolley (1,500 kg) compared to the FWRB test. The trend of increased vehicle stiffness (especially illustrated by tests with the MPDB and small cars) shows the need of a further improvement of passive restraint systems to reduce the occupant loading and with it the injury risk. The analyzed GIDAS data confirm the higher injury risk for occupants in cars with an accident weight of less than 1,500 kg compared to those with a crash weight above 1,500 kg in car-to-car and car-to-object or car-to-HGV, respectively. Furthermore the injury risk increases with decreasing mass ratio (i.e., the opponent car is heavier) in car-to-car accidents. Independent from the higher injury risk, the risk for passenger compartment intrusion in frontal impact appears not to be independent on the crash weight of the car.
Um die Wirkung hochgesetzter Bremsleuchten auf das Uunfallgeschehen abzuschätzen, wurde eine Reihe von Untersuchungen eingeleitet. Die Zusammenfassung ihrer Ergebnisse: 1. Der Anteil der Pkw mit hochgesetzten Bremsleuchten ist gering und scheint weiter zu sinken. 2. Die Wirkung hochgesetzter Bremsleuchten kann noch nicht abschließend beurteilt werden. Es gibt aber Hinweise dafür, dass die auf Grund von Experimenten erwarteten positiven Effekte aus einer Reihe von Gründen relativiert werden müssen: - Wahrnehmungs- (Tiefen- und Entfernungseindruck) und Bremsgewohnheiten des Alltags entsprechen nicht den experimentellen Bedingungen; - Kompensationsverhalten auf Grund vermeintlich besserer Bremssignalisierung ist nicht auszuschließen; - hochgesetzte Bremsleuchten werden von den Betroffenen kontrovers beurteilt, teilweise nicht ohne starke Emotionen; - für das normale alltägliche Bremsverhalten sind Informationen über die Stärke der Verzögerung des Vordermanns wünschenswerter als der bloße Hinweis "Fahrer bremst". 3. Verletzungen von Pkw-Insassen durch hochgesetzte Bremsleuchten sind nicht zu erwarten. 4. Um ein positives Gesamtergebnis bei der Gegenüberstellung von Nutzen und Kosten zu erreichen, müssten hochgesetzte Bremsleuchten etwa 10 % der Folgen des theoretisch zu beeinflussenden Unfallpotentials vermeiden. 5. 36 % der befragten Autofahrer fordern ein Verbot hochgesetzter Bremsleuchten, 20 % eine Einbauvorschrift.
Schutz von Fahrzeuginsassen
(1983)
Ausgehend von unfallstatistischen Daten und Ausführungen über Unfallablauf und Unfallfolgen werden Schutzmaßnahmen diskutiert, die das Verletzungsrisiko für Fahrzeuginsassen möglichst niedrig halten. Die Wirksamkeit von Schutzmaßnahmen wird beeinflusst von der Unfallkonstellation, Eigenschaften der Pperson und vom Fahrzeug (Deformationscharakteristik, Auslegung des rückhaltesystems). Die Gesamtwirksamkeit hängt wiederum ab von der Wirksamkeit des Rückhaltesystems, der Benutzungshäufigkeit und der Benutzungsqualität. Die Arbeit endet mit volkswirtschaftlichen Überlegungen und kommt zu dem Schluss, dass auch in Zukunft als wichtigste Maßnahme zum Schutz von Fahrzeuginsassen die Erhöhung der Anlegequote für Sicherheitsgurte anzusetzen ist.
Für die Überprüfung eines Zusammenhangs zwischen Verkehrssicherheit und Arzneimittel wurde mit Hilfe eines Vergleichs einer Kontroll- und Medikamentengruppe durch Labortests und eigens konstruierten Fahraufgaben die Frage untersucht, ob eine Beurteilung der Versuchspersonen anhand der Ergebnisse aus den Labortests zu ähnlichen Ergebnissen führt wie eine Bewertung aufgrund der Fahrversuche. Zwar wurden teilweise Übereinstimmungen zwischen Labortests und Fahraufgaben festgestellt, es kann jedoch für die einzelne Versuchsperson nicht geschlossen werden, dass sie anhand der Fahraufgaben ähnlich beurteilt wird wie dies mit den Labortests der Fall ist. Es werden Vorschläge für die Weiterentwicklung von Fahrproben unterbreitet.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschreiben. Das Ergebnis kann indes nicht zufriedenstellen: Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird hier, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschreiben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen. Dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
Schutz von schwächeren Verkehrsteilnehmern: kommende Anforderungen aus Gesetzgebung und Euro NCAP
(2017)
Systeme der aktiven Fahrzeugsicherheit, insbesondere Notbremsassistenzsysteme und automatische Notbremssysteme, haben in den letzten zwei Dekaden große technische Fortschritte gemacht, und das im Wesentlichen ohne "Druck" von Gesetzgeber oder unabhängigen Testorganisationen " diese können aber durch passende Anforderungen den Vormarsch der Systeme in die Breite und die Ausnutzung von ansonsten für den Hersteller vielleicht nicht wirtschaftlichen Potentialen unterstützen. Dieser Bericht hat das Ziel, einen Überblick über die kommenden Anforderungen an Schutzsysteme für schwächere Verkehrsteilnehmer zu geben und diese Anforderungen in den Kontext Euro NCAP (=welchen Einfluss haben diese Anforderungen auf die Gesamtbewertung?) sowie Gesetzgebung (schwächere Anforderungen, aber dafür ein Markteintrittskriterium) zu stellen: - Anforderungen und Testprozeduren für Notbremsassistenz Fahrradunfälle 2018 und 2020 in Euro NCAP; - Anforderungen und Testprozeduren für Notbremsassistenz bei Nachtunfällen mit Fußgängern in Euro NCAP 2018; - Anforderungen und Testprozeduren für Abbiegeassistenzsysteme zum Schutz von Radfahrern in Unfallsituationen mit rechtsabbiegenden Lkw innerhalb der Fahrzeugtypgenehmigung.
Für eine Reihe von EU Regelungen im Bereich Fahrzeugsicherheit erlaubt eine Verordnung bereits seit dem Jahr 2010 virtuelles Testen für die Typzulassungsprüfung. Technische Details bzw. konkrete Prozeduren für spezifische Regelungen sind in dieser Verordnung jedoch nicht enthalten. Das Hauptziel des europäischen Projekts IMVITER (lmplementation of Virtual Testing in Safety Regulations) war es, basierend auf der neuen Verordnung ein virtuelles Testverfahren auszuarbeiten und dabei offene Fragen zu berücksichtigen. Um die im Projekt-Konsortium unter Berücksichtigung der Anliegen aller Interessensgruppen wie Autohersteller, Zulassungsbehörden und technischer Dienste erarbeiteten offenen Punkte zu adressieren, wurde ein generisches Flussdiagramm entwickelt, das den Ablauf einer virtuell basierten Typprüfung darstellt. ln diesem Diagramm ist der virtuelle Typgenehmigungsprozess in drei aufeinander folgende Phasen aufgeteilt, die Verifikations-, Validierungs- und Typgenehmigungsphase. Von entscheidender Bedeutung ist die Phase der Validierung des Simulationsmodells, für die im IMVITER-Projekt eine Methodik vorgeschlagen wurde. Mit der im Projekt vorgeschlagenen Validierungsmethode ist kein Austausch des Simulationsmodells zwischen Fahrzeughersteller und technischem Dienst notwendig, so dass die Vertraulichkeit von Betriebsgeheimnissen nicht gefährdet ist. Zur Validierung des Modells werden jedoch immer Versuche notwendig sein. Dies gilt sowohl für die Überpruefung von passiven als auch aktiven Fahrzeugsicherheitssystemen. Eine zusammenfassende Betrachtung der Erfahrungen aus dem IMVITER-Projekt ergab, dass mit der Einführung von virtuellem Testen keine Erhöhung der Anforderungen an die Fahrzeugsicherheit bzgl. bestehender Regelungen verbunden sein sollte. Jedoch werden auch weiterhin neue zusäztliche Regelungen erforderlich sein, da sich das Unfallgeschehen und die Fahrzeugtechnologie weiterentwickeln und ändern werden. Diese sollten von Beginn an die Möglichkeiten des virtuellen Testens nutzen, insbesondere bei Testverfahren für neue Technologien, z.B. aktiver Fahrzeugsicherheitssysteme. Hier bieten virtuelle Testverfahren nicht nur eine Kosten- oder Zeitersparnis, sondern ermöglichen teilweise erst die sinnvolle Abprüfung von neuen Sicherheitssystemen, die mit aktuellen auf Hardware-Test basierenden Verfahren überhaupt nicht möglich wären.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben. Das Ergebnis kann indes nicht zufriedenstellen. Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird im Beitrag, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der sich auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschrieben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen; dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
Causation of traffic accidents with children from the perspective of all involved participants
(2017)
In the year 2014 about 2,800 children between zero and 14 years got injured due to traffic accidents in Austria. More than 50% were taking part in traffic as active road users like cyclists or pedestrians. Within this study 46 real world traffic accidents between vehicles and children as pedestrians were analysed. In 39 cases, car drivers hit the crossing children. In the other cases, the collision opponents were busses, trucks or motorcycles. Most of the children got hit while crossing a road at urban sites. By analysing the traffic accidents from the perspectives of all involved participants, vehicle drivers and injured children, it is possible to identify factors for each participant, which led to the accident and factors that contributed the accident. The main task is to find patterns in the behaviour of crash victims (children and driver) before the collision. One important fact is that in more than 50% of the analysed cases sight obstructions were an important contributing factor for both, the driver and the child. From drivers view situations in which the child moved unexpected into the driven road lane were often found. For the injured child, factors like: no attention to the road traffic or no sufficient traffic observation were found to be relevant. Further it- possible to sensitise children and adults to possible source of critical traffic situations according to the findings of this study.
The proportion of older road users is increasing because of demographic change (in the group 65+ from current 18% to about 24% by 2030). The mobility needs of people 65+ often differ from those of younger people. Seniors (65+) are already more involved in fatal accidents than younger road users. According to the age development, the senior share of road deaths in the EU of today is increasing nearly one-fifth to one-third. From the in-depth analysis of accidents generic simulation models were developed. Attention has been paid both to psycho-physical characteristics as well as on the social and physical environment and their specifics in conjunction with seniors. By simulating the defined scenarios and varying the defined relevant parameters, accident influencing factors were examined as a basis for avoidance. In addition, the parameters were varied to show the influence from the vehicle, the pedestrian and the infrastructure to avoid the accident or to characterize the conditions for which the accident is inevitable.
Injury probability functions for pedestrians and bicyclists based on real-world accident data
(2017)
The paper is focusing on the modelling of injury severity probabilities, often called as Injury Risk Functions (IRF). These are mathematical functions describing the probability for a defined population and for possible explanatory factors (variables) to sustain a certain injury severity. Injury risk functions are becoming more and more important as basis for the assessment of automotive safety systems. They contribute to the understanding of injury mechanisms, (prospective) evaluation of safety systems and definition of protection criteria or are used within regulation and/or consumer ratings. In all cases, knowledge about the correlation between mechanical behavior and injury severity is needed. IRFs are often based on biomechanical data. This paper is focusing on the derivation of injury probability models from real world accident data of the GIDAS database (German In-depth Accident Study). In contrast to most academic terms there is no explicit term definition or definition of creation processes existing for injury probability models based on empirical data. Different approaches are existing for such kind of models in the field of accident research. There is a need for harmonization in terms of the used methods and data as well as the handling with the existing challenges. These are preparation of the dataset, model assumptions, censored/unknown data, evaluation of model accuracy, definition of dependent and independent variable, and others. In the presented study, several empirical, statistical and phenomenological approaches were analyzed regarding their advantages and disadvantages and also their applicability. Furthermore, the identification of appropriate prediction parameters for the injury severity of pedestrians has been considered. Due to its main effect on injuries of pedestrians and bicyclists, the importance of the secondary impact has also been analyzed. Finally, the model accuracy, evaluated by several criteria, is the rating factor that gives the quality and reliability for application of the resulting models. After the investigation and evaluation of statistical approaches one method was chosen and appropriate prediction variables were examined. Finally, all findings were summarized and injury risk functions for pedestrians in real world accidents were created. Additionally, the paper gives instructions for the interpretation and usage of such functions. The presented results include IRFs for several injury severity levels and age groups. The presented models are based on a high amount of real world accidents and describe very well the injury severity probability of pedestrians and bicyclists in frontal collisions with current vehicles. The functions can serve as basis for the evaluation of effectiveness of systems like Pedestrian-AEB or Bicycle-AEB.
In 2016 the seventh ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Im Rahmen des weltweiten ESV-Programmes (Enhanced Safety of Vehicles) werden seit mehreren Jahren internationale Forschungsbemühungen unternommen (International Harmonized Research Activities, IHRA), um im Vorfeld der Gesetzgebung die wissenschaftlichen Grundlagen gemeinsam zu erarbeiten. Ziel der IHRA-Arbeiten ist es, auf der Grundlage dieser Forschungsergebnisse die Harmonisierung der Vorschriften zu erleichtern. Eine besondere Aktivität bezieht sich auf Intelligent Transportation Systems (ITS). Im vorliegenden Beitrag wird die Aufgabe dieser IHRA-ITS-Arbeiten geschildert, sowie der derzeitige Stand der Forschungsbemühungen beschrieben. Es zeigt sich, dass die beschriebene Sicherheitsbewertung eine Fülle von Fragestellungen aufwirft und weitere Forschungsanstrengungen erfordert. Die zukünftigen Bemühungen sind darauf gerichtet, in internationaler Zusammenarbeit und Arbeitsteilung die als besonders wichtig erkannten Themen zur Bewertung der fahrzeugseitigen Fahrerassistenzsysteme zu bearbeiten.
Ausgehend von den Unfalldaten der letzten Jahre wird die Bedeutung von Fußgängerunfällen im Unfallgeschehen dargestellt. Betrachtet man die bei Unfällen getöteten Verkehrsteilnehmer, so sind am häufigsten Personen in Kraftfahrzeugen betroffen. Am zweithäufigsten werden, gemäß der Unfallstatistik, Fußgänger getötet. Eine Möglichkeit zur Verbesserung des Schutzes von Fußgängern und anderen sogenannten "ungeschützten Verkehrsteilnehmern" im Falle einer Kollision mit einem Kraftfahrzeug sind Maßnahmen am Fahrzeug. Um die Wirksamkeit derartiger Maßnahmen zu beurteilen, wurde durch das EEVC (European Enhanced Vehicle-Safety Committee) ein Prüfverfahren entwickelt. Es handelt sich dabei um ein Komponentenprüfverfahren, mit dem die Frontstruktur von Fahrzeugen, die bei einer Kollision mit einem Fußgänger hauptsächlich betroffen ist, geprüft wird. Es werden keine den gesamten Menschen repräsentierende Dummies verwendet, stattdessen werden Prüfkörper, die einzelne Körperteile simulieren, eingesetzt. Dieser EEVC Vorschlag wird geschildert. Darüber hinaus wird über Aktivitäten außerhalb des EEVC berichtet, sowie über den aktuellen Stand der Bemühungen der Europäischen Kommission in Bezug auf den Fußgängerschutz, die derzeit, auf Grundlage des Prüfvorschlages des EEVC, einen Vorschlag für eine Europäische Richtlinie erarbeitet.
In der Europäischen Union (EU) gab es 1999 circa 1,3 Millionen Straßenverkehrsunfälle mit Personenschaden, wobei circa 42.000 Personen getötet wurden. Ziel der EU ist es diese Zahl auf 25.000 im Jahr 2010 zu senken. Die EEVC befasst sich bereits seit Anfang der 80er Jahre mit der Thematik Fußgängerschutz in verschiedenen Arbeitsgruppen. Im Dezember 1998 legte die EEVC-Arbeitsgruppe 17 "Fußgängersicherheit" ihren Abschlussbericht vor, in dessen Anhang ein Prüfverfahren zum fahrzeugseitigen Fußgängerschutz enthalten ist. Dieses Prüfverfahren wird vorgestellt. Es basiert auf Komponententests. Unterschieden werden drei Prüfkörperarten und insgesamt vier Prüfkörper. Aus wissenschaftlicher Sicht und aus Sicht der Unfallforschung empfiehlt die EEVC-Arbeitsgruppe 17 eine umfassende Einführung des vorgeschlagenen Prüfverfahrens mit allen Prüfkörpern, gegebenenfalls in Form einer stufenweisen Einführung.
Seit 1997 gibt es in Europa unter dem Namen Euro NCAP (European New Car Assessment Programme) einheitliche Test- und Ratingverfahren. Sie liefern Informationen über den Insassen- und über den Fußgängerschutz. Euro NCAP hat seither fast 90 Fahrzeugmodelle in jeweils drei unterschiedlichen Crashtest-Konfigurationen untersucht und die Ergebnisse den europäischen Konsumenten zugänglich gemacht. Im Beitrag wird auf die Testbedingungen, die Euro NCAP-Ratingverfahren sowie auf die Weiterentwicklung von Euro NCAP eingegangen. Ein wichtiger Aspekt wird dabei auch die weltweite Harmonisierung der Test- und Ratingverfahren sein.
Das Fahrverhalten ändert sich mit zunehmendem Alter. Damit ändern sich auch die Risiken. Neben den jungen Fahranfängern im Alter von 18 bis etwa 25 Jahren stellen Fahrer über 75 Jahre eine besondere Problemgruppe dar. Mit zunehmender Zahl alter Fahrer (demographische Entwicklung plus Zunahme der Fahrerlaubnisinhaber in dieser Altersgruppe) besteht hier in naher Zukunft akuter Handlungsbedarf. Ansatzpunkte gibt es im gesamten Mensch-Maschine-Umwelt-System. Fahrzeuge müssen vermehrt im Hinblick auf alte Fahrer konstruiert und optimiert werden. Die Infrastruktur muss den Bedürfnissen einer eindeutigen Verkehrsführung angepasst werden. Aber nur, wenn der Mensch selbst geeignet ist, als Fahrer am Straßenverkehr teilzunehmen, ist ein Gewinn bei der Verkehrssicherheit zu erwarten. Dies muss gewährleistet werden. Wichtig ist, dass die Problematik der alten Fahrer als solche erkannt wird und schnell eine tragfähige Lösung für die Zukunft gefunden wird.
Although the annual traffic accident statistics published by the national police is available in public, the detailed traffic accident data has not been released in Korea. Recently the Ministry of Land, Infrastructure and Transport recognized the importance of in-depth accident data to enhance road traffic safety and initiated a research project to establish a collection of the detailed accident data. The main objective of the project is a feasibility study to establish KIDAS (Korea In-Depth Accident Study). Within this project, three university hospitals which are located in mid-size cities have been selected to collect accident data. Annually, more than 500 cases of accidents have been collected from the in-patient's interviews and diagnosis. Unlike GIDAS (German In-Depth Accident Study), currently on-site investigation can"t be performed by the Korean police. The only available data is patient medical records, patient's description of accident circumstances and the damaged vehicle. Occasionally the police provide the accident investigation reports containing very brief information on accident causation and vehicle safety. In a first step, the concept of KIDAS is to adopt the format of iGLAD (Initiative for the Global Harmonization of Accident Data) for harmonization. Since the currently collected accident information is extremely limited compared with GIDAS, the other sources of data and calculations such as KNCAP vehicle data, pc-crash simulations, vehicle registration information, insurance company data are utilized to complete the iGLAD template. Results from KIDAS_iGLAD and the cases of assessment of active safety devices such as AEBS, ESC, and LDWS will be evaluated.
Road accidents are typically analyzed to address influences of human, vehicle, and environmental (primarily infrastructure) factors. A new methodology, based on a "Venn diagram" analysis, gives a broader perspective on the probable factors, and combinations of factors, contributing both to the occurrence of a crash and to sustaining injuries in that crash. The methodology was applied to 214 accidents on the Mumbai-Pune expressway. Factors contributing to accidents and injuries were addressed. The major human factors influencing accidents on this roadway were speeding (30%) and falling asleep (29%), while injuries were primarily due to lack of seat belt use (46%). The leading infrastructure factor for injuries was impact with a roadside manmade structure (28%), and the main vehicle factor for injuries was passenger compartment intrusion (73%). This methodology can help identify effective vehicle and infrastructure-related solutions for preventing accidents and mitigating injuries in India.
Pedestrians represent about 20% of the overall fatalities in Europe- road traffic accidents. In this paper a methodology is proposed to understand why the numbers are so high, especially in the south of Europe and particularly in Portugal, . First a detailed statistical analysis using Ordinal Logistic Regression model (OLR) was applied to the gathered data from all Portuguese accidents with victims in the period 2010-2012. In a second stage accident reconstruction computational techniques using pedestrian biomechanical models are used to evaluate the accident conditions that lead to the injuries, such as the speed and the impact location. For biomechanical injury criterions, the AIS (Abbreviated Injury Scale), the HIC (Head Injury Criterion) and other injury criterions based on the resulting accelerations in the pedestrian's body are used. The statistical model reported that there were several predictors that significantly influenced the pedestrian injury severity in the event of a road accident, such as Pedestrian's age, Pedestrian's gender, Vehicle Design/Category or Driver's gender. The use of injury scales and biomechanical criterions in in-depth investigation of road accidents, such as AIS, can significantly improve the quality of the reconstruction process.
India is one of the leading countries reporting highest road accidents & related injuries. TMARG (Tata Motors Accident Research Group) has been recording crashes in association with M/s. Lokamanya Medical Foundation since 2011 with M/s, Amandeep Hospitals since Aug 2013. This study has highlighted some accident types not discussed extensively in literature. Trucks to Truck impacts " Cabin interaction with overhanging loadbody structures and Offset underside impacts for passenger vehicles are seen in significant numbers. The paper discusses these in more detail including severity.
In 2014 the sixth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Topics of this report are: Road construction (highways, interstate roads, urban by-passes, cycle tracks, construction sites, level crossings removal), traffic management systems, road tunnel equipment, harmonisation of vehicle regulations, accident statistics and accident research, passive vehicle safety, active vehicle safety , automotive environmental protection and rescue systems.
EEVC Status report
(2001)
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
When the EEVC proposed the full-scale side impact test procedure, it recommended that consideration should be given to an interior headform test in addition. This was to evaluate areas of contact not assessed by the dummy. EEVC Working Group 13 has been researching the parameters of a possible European headform test procedure in four phases. Earlier stages of the research have been presented at previous ESV conferences. The conclusions from these have suggested that the US free motion headform should be used in any European test procedure and that it should be a free flight test, not guided. This research has now culminated in proposals for a European test procedure. This paper presents the proposed EEVC side impact interior headform test procedure, giving the rationale for the test and the first results from the validation phase of the test protocol.
The objective was to develop and validate a crash trolley (reference vehicle) equipped with a compartment and a full restraint system for driver and front seat passenger which can be used in full scale crash testing. Furthermore, the crash trolley should have a suspension to show rotation and nick effects similar to real vehicles. Within the development phase the reference vehicle was build based on a European family car. Special attention was needed to provide appropriate strength to the trolley and its suspension. The reference vehicle is equipped with a restraint system consisting of airbags, pedals, seats, dashboard, and windscreen. On the front of the vehicle different crash barriers can be installed to provide miscellaneous deceleration pulses. For the validation phase a series of low and high speed crash tests with HIII dummies were conducted and compared with full scale tests. For the comparison deceleration pulse, dummy numbers and vehicle movement were analyzed. Validation tests with velocities up to 60 km/h showed promising results. The compartment and the suspension systems stayed stable. Rotation effects were comparable with full scale car crash tests. The airbags and seat belt system worked reasonable. The acceleration pulse compared to an Euro NCAP test had a similar characteristic but was in general slightly lower. After the successful validation the reference vehicle is already in use in different studies in the field of vehicle safety research at BASt.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
There is a need to continue to set the right vehicle safety policy priorities in the future. Research has to point out the most cost efficient and safety relevant measures to further reduce the number of road traffic casualties. The overall development shows that the constant and rapid decrease in the number of road casualties slows down. New innovations need to enter the vehicle market soon, in order to continue the success achieved in the last decade. Priorities for vehicle safety are driven by safety and mobility demands. It is necessary to keep a strong lid on all aspects of elderly and vulnerable road users. The fraction of powered-two-wheelers (PTW) is a priority group. PTWs have a risk of being involved in an accident, 14times higher than that of a passenger car. However, the figures do also show that every second fatality is a car occupant. Therefore passenger car safety remains to be top priority. Heavy goods vehicles are overly represented in fatal accidents, addressing the need to make these vehicles more compatible with other road users. These facts highlight the necessity not only to increase vehicles" self protection, but also to make cars - and trucks - more compatible and safe. Cycling is a strongly increasing mode of transport. This is a further reason to demand better protection for cyclists and pedestrians from car design and car active and integrated safety systems. Another priority for future vehicle safety is related to demographics. It is less known that the purely demographic effect will be superimposed by an increasing wish of elderly people to be mobile. However, elderly people show deficits concerning their biomechanics. This emphasizes the need for better and more adaptive restraint systems, but also further technological challenges and demands for active safety systems. However, in order to progress, current technological limitations have to be overcome. Cost benefit considerations, but also consumer acceptance and desires, will drive this process.
Since 2008, the authors inspected fatal traffic accidents on the spot every year, with the cooperation of Toyota police station in Aichi pref. In the jurisdiction, numbers of fatal accidents were 18 in 2008, 12 in 2009, 14 accidents in 2010, and 16 in 2011. We here report the results of our analysis of information obtained by detailed inspection for those that occurred from 2008 to 2010. We focused on vehicle-to-pedestrian accidents, which accounted for about 45% of all accidents in 2008. Because many accidents occurred on residential roads not far from pedestrians" homes, it was revealed that the decrease of the collision speed by traffic calming such as humps and zone speed management, was highly effective. On the other hand, pedestrian detection technologies seemed to be also effective as a countermeasure on vehicle side. Every pedestrian position against a vehicle was clarified and TTC (Time to Collision) was calculated provisionally. Pedestrian accidents in intersections were also examined. Among the intersection pedestrian accidents within the jurisdiction, compared with the national average in Japan, the ratio of intersections without a signal and the ratio without a pedestrian crossing were high. According to the comparison of the Japanese traffic accident patterns between 2001 and 2008, pedestrian accidents during turning right and turning left did not decrease much. For elderly drivers, these accidents occurred very often. Finally, single vehicle accidents were analysed with the accident pattern analysis methods used above. There were high numbers of single vehicle accidents against object on single roads. Although fatal accidents against guardrails decreased, the numbers of fatal accidents against a utility pole and a sign pole were nearly constant. As for the impact with narrow width objects such as utility poles, the fatality rate was very high, and countermeasures of both road infrastructure and vehicles seem to be effective.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
The objective of the study is to measure the risk of pedestrian and bicyclist in urban traffic through an analysis of real-world accident data. The kinematics and injury mechanisms for both pedestrian and bicyclists are investigated to find the correlation of injury risks with injury related parameters. For this purpose, firstly 338 cases are selected as a sample from an IVAC accident database based on the In-depth Investigation of Vehicle Accident in Changsha of China. A statistic measurement of the fatality and serious injury risks with respect to impact speed was carried out by logistic regression analysis. Secondly, 12 pedestrian and 12 bicyclist accidents were further selected for reconstruction with MADYMO program. A comparative analysis was conducted based on the results from accident analysis and computer reconstructions for the injury risk, head impact conditions and dynamic response of pedestrians and bicyclists. The results indicate that bicyclists suffered lower risks of severe injuries and fatalities compared with pedestrians. The risks of AIS 3+ injury and fatality are 50% for pedestrians at impact speeds of 53.2 km/h and 63.3 km/h, respectively, while that for bicyclists at 62.5 km/h and 71.1 km/h, respectively. The findings could have a contribution to get a better understanding of pedestrians" and bicyclists" exposures in urban traffic in China, and provide background knowledge to generate strategies for pedestrian protection.
In 2012 the fifth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Im Jahr 2004 fand an der Medizinischen Hochschule Hannover die erste ESAR-Konferenz (Expert Symposium on Accident Research) statt. Die Idee einer internationalen Konferenz war aus der Notwendigkeit entstanden, diejenigen Experten zusammen zu bringen, die weltweit tätig sind und Verkehrsunfälle wissenschaftlich analysieren, um ihre Ergebnisse gemeinsam zu diskutieren und einem Zielpublikum von Behördenvertretern, Entwicklungsingenieuren der Automobilindustrie und anderen Wissenschaftlern darzubringen. Die durch Professor Otte initiierte und nun zum vierten Male organisierte Konferenz fand eine breite Akzeptanz und ist mittlerweile Bestandteil einer Konferenzlandschaft mit Zielvorträgen von der Fahrzeugsicherheit bis hin zur Verletzungsanalyse und den Unfallursachen. ESAR kann als wissenschaftliches Kolloquium und Plattform für einen Informationsaustausch der Unfallforscher angesehen werden, die sich speziell mit Methoden der Unfalluntersuchung, mit Verletzungsmechanismen und der Bewertung von Verletzungen, Unfallursachen und anderen Bereichen der statistischen Unfalldatenanalyse befassen. Experten aus den Bereichen der Medizin, der Verkehrspsychologie und der Technik sowie Vertreter zuständiger Behörden kommen hier zusammen, um die Erfahrungen in der Unfallprävention und der Unfallrekonstruktion zu diskutieren und um der Forschung neue Felder zu eröffnen. Neben den Belangen der Europäischen Gemeinschaft werden auch die weltweit zu registrierenden hohen Verletztenzahlen berücksichtigt. Wissenschaftliche Vorträge aus aller Welt tragen dazu bei, geeignete Maßnahmen und Methoden zur Analyse und drastischen Verringerung der Zahl der bei Verkehrsunfällen Getöteten zu entwickeln. Die Zusammensetzung des Teilnehmerkreises dieser wie früherer ESAR-Konferenzen hat längst eine über Europa hinausgreifende Internationalitaet erreicht und bietet daher einen aufschlussreichen Überblick über die verschiedenen Standards bestehender Verkehrssicherheit und unterschiedlichen Unfallszenarien und über die Anforderungen an die Unfallanalysen. Die Ergebnisse langjähriger Forschungsarbeiten in Europa, USA, Australien und asiatischen Ländern beinhalten unterschiedliche infrastrukturelle Zusammenhänge und geben Erkenntnisse über Population, Fahrzeugbestand und Fahrereigenschaften. Derartige Informationen bilden eine exzellente Basis für abzuleitende Empfehlungen und Maßnahmen für die Erhöhung der Verkehrssicherheit international.
This work aims at bringing evidence for mass incompatibility in frontal impact for cars built according to the UNECE R94 regulation. French national injury accidents database census for years 2005 to 2008 were used for the analysis. The heterogeneity of frontal self-protection among cars of different masses is investigated, as well as the partner protection parameter offered by these cars. The last part of the analysis deals with the estimation of the benefit, in terms of fatal and severe injuries avoided, if crashworthiness was harmonized for the whole fleet of vehicle. This calculation is done for France and is extended to all Europe.
Looking at the total of sum of fatal car accidents the number of single-vehicle accidents and particularly run-offroad (ROR) accidents are most frequent. In Austria on the Autobahn ROR accidents amounts to almost 45% of all fatal accidents, i.e. nearly every second fatal accident is caused by ROR accidents and interaction with infrastructure. Approximately 43 people were killed on Autobahns in ROR accidents with passenger cars. One possibility of protection against impacts with infrastructure is the use of guardrails. However, the initial element identified as a turned down terminal could become a dangerous impact object. These turned down terminals may lead a vehicle to roll over or the car "takes-off" when impacting the turned down guardrail. In many cases it is reported that the vehicle is jumping into road side objects such as traffic sign poles or overpasses. On average, nine people are killed in such accidents every year in Austria.
Accident data shows that the vast majority of pedestrian accidents involve a passenger car. A refined method for estimating the potential effectiveness of a technology designed to support the car driver in mitigating or avoiding pedestrian accidents is presented. The basis of the benefit prediction method consists of accident scenario information for pedestrian-passenger car accidents from GIDAS, including vehicle and pedestrian velocities. These real world pedestrian accidents were first reconstructed and the system effectiveness was determined by comparing injury outcome with and without the functionality enabled for each accident. The predictions from Volvo Cars" general Benefit Estimation Model are refined by including the actual system algorithm and sensing models for a relevant car in the simulation environment. The feasibility of the method is proven by a case study on a authentic technology; the Auto Brake functionality in Collision Warning with Full Auto Brake and Pedestrian Detection (CWAB-PD). Assuming the system is adopted by all vehicles, the Case Study indicates a 24% reduction in pedestrian fatalities for crashes where the pedestrians were struck by the front of a passenger car.
In a first step, we have examined approximately 23 000 single vehicle accidents within the Austrian National Statistics database. In a second step, we considered 15% of all fatal "running off the road" accidents that occurred in Austria in 2003. As a result, two accident categories were specified; "leaving the road without preceding manoeuvre" and "leaving the road with preceding manoeuvre". These two categories can be basically characterised by the vehicle- heading angle and its velocity angle. In this report, we further suggest theoretical approaches for the dimensioning of a safety zone, an area adjacent to the road free of fixed objects or dangerous slopes. We also show the link between the two accident categories mentioned above and the real world accidents analysed in detail. These observations also form the basis for the required length for safety devices. Finally, we summarise accident avoidance strategies.
Empirical vehicle crashworthiness studies are usually based on national or in-depth traffic accident surveys: Data on accident-involved cars/drivers are analysed in order to quantify the chance of driver injury and to assess certain risk factors like car make and model. As the cars/drivers involved in the same accident form a "cluster", where the size of the cluster equals the number of accident-involved parties, traffic accident survey data are typical multi-level data with accidents as first-level or primary and cars/drivers as secondlevel or secondary units (car occupants in general are to be considered as third level units). Consequently, appropriate statistical multi-level models are to be used for driver injury risk estimation purposes as these models properly account for the cluster structure of traffic accident survey data. In recent years various types of regression models for clustered data have been developed in the statistical sciences. This paper presents multi-level statistical models, which are generally applicable for vehicle crashworthiness assessment in the sense that data on single and multiple car crashes can be analysed simultaneously. As a special case of multi-level modelling driver injury risk estimation based on paired-by-collision car/driver data is considered. It is demonstrated that assessment results may be seriously biased, if the cluster structure inherent in traffic accident survey data is erroneously ignored in the data analysis stage.
Electronic Stability Program (ESP) aims to prevent the lateral instability of a vehicle. Linked to the braking and powertrain systems, it prevents the car from running wide on a corner or the rear from sliding out. It also helps the driver control his trajectory, without replacing him, in the case of loss of control where the driver is performing an emergency manoeuvrer (confused and exaggerated steering wheel actions). A new ESP function optimizes ESP action in curves with hard under steering (situations in which the front wheels lose grip and the vehicle slides towards the outside of the curve). A complementary feature prevents the wheels from spinning when pulling away and accelerating. The name given to the ESP system varies according to the vehicle manufacturer, but other terms include: active stability control (ASC), automotive stability management system (ASMS), dynamic stability control (DSC), vehicle dynamic control (VDC), vehicle stability control (VSC) or electronic stability Control (ESC). This paper proposes an evaluation of the effectiveness of ESP in terms of reduction of injur accidents in France. The method consists of 3 steps: - The identification, in the French National injury accident census (Gendarmerie Nationale only), of accident-involved cars for which the determination of whether or not the car was fitted with ESP is possible. A sample of 1 356 cars involved in injury accidents occurred in 2000, 2001, 2002 and 2003 was then selected. But we had to restrict the analysis to only 588 Renault Lagunas. - The identification of accident situations for which we can determine whether or not ESP is pertinent (for example ESP is pertinent for loss of control accidents whilst it is not for cars pulling out of a junction). - The calculation, via a logistic regression, of the relative risk of being involved in an ESPpertinent accident for ESP equipped cars versus unequipped cars, divided by the relative risk of being involved in a non ESP-pertinent accident for ESP equipped cars versus unequipped cars. This relative risk is assumed to be the best estimator of ESP effectiveness. The arguments for such a method, effectiveness indicator and implicit hypothesis are presented and discussed in the paper. Based on a few assumptions, ESP is proved to be highly effective. Currently, the relative risk of being involved in an ESP pertinent accident for ESP-equipped cars is lower (-44%, although not statistically significant)rnthan for other cars.rn
Rollover scenarios in Europe
(2005)
Rollover accidents seem to be a rising problem in Europe and therefore the systematic of this accident scenario should be investigated. Based on statistical investigations on major European accident databases for different countries a series of 73 real world rollover accidents was analysed. These cases were reconstructed using PC-Crash and preliminary categorised using a modified USbased rollover classification. In a first step, the rollover events were reconstructed from the point of conflict to the vehicle- rest position. The vehicles kinematics as well as its linear and rotational velocities were derived. In a second step typical velocity characteristics as well as kinematics were identified and the events categorised according to these criteria. Based on these results four main categories were defined, covering all reconstructed accidents. This categorisation was based on mechanical parameters (rotatory and translator kinematical data of the vehicle). Significant differences can be seen for different scenarios for the "first phase of rollover".
This paper describes the methodology of In-Depth Investigation in Germany on the example of GIDAS (German In-Depth Accident Study). Since 1999 in Germany a joint project between FAT (Forschungsvereinigung Automobiltechnik or Automotive Industry Research Association) and BASt (Bundesanstalt für Straßenwesen or the Federal Road Research Institute) is being carried out in Hannover and Dresden. The methodology of this project is based on a statistically orientated procedure of data sampling (sampling plan, weighting factors). The paper describes the possibilities of such in-depth investigation on the results of the offered title. The accident cases were collected randomly within GIDAS at Hannover. There are more cases existing from previous investigation started in 1985 under the same methodology. The portion of rollovers can be established at 3.7% of all accidents with casualties in the year 2000. For the study 434 cases of car accidents with rollovers are used for a detail comprehensive analysis. The accidents happened in the years 1994 to 2000 in the Hannover area. The injury distribution will report about 741 occupants with rollover accident event. The presented paper will give an overview of the accident situations following in rollover movements of cars. The distributions of injury frequencies, injury severity AIS for the whole body and for the body regions of occupants will be presented and compared to technical details like the impact speed and the deformation pattern. The speed of the car was determined at the point of rollover and on the point of accident initiency. The characteristics of the kinematics followed in a rollover movement are analyzed and the major defined types of rollover will be shown in the paper. The paper will describe the possibilities of In-Depth Investigation methods for the approach of finding countermeasures on the example of car accidents with rollover and explaining the biomechanics of injuries in rollover movements.
This paper set out to examine the possibilities for injury avoidance implications for older drivers in crashes, based on crash and injury patterns among older drivers and current trends in ageing in most western societies. A number of safety technologies were identified and discussed which have potential for improving vehicle older driver crash avoidance and crashworthiness. While there were some promising estimates available of the likely benefits of this technology for improving safety, it is evident that they need to be confirmed for older drivers, given their age-related disabilities and sensory limitations. Further research is urgently required to ensure that these technologies yield safety benefits without any disbenefits for older drivers.rn
This report gives an overview of pedestrian accidents on Japanese roads. Database used for the analysis is national traffic accident data based on police reports. Relevant measures and background information ranging from vehicle safety, engineering and education are briefly reviewed, and area for further improvement is discussed.rn
In order to improve the protection of children transported in cars, within the CHILD programme (GR3D-CT2002-00791) real world road accidents are thoroughly analysed and then reconstructed in laboratory. Prior to comparing injury severities of real victims to physical parameter values measured on the dummies, the quality of the reconstructions is evaluated by experts who use their experience based on the investigation of numerous and various accidents. This paper presents a new tool aiming at better evaluating and validating accident reconstructions. It is based on statistical evaluation of vehicle deformations which gives weighing factors for every part of the car body structure finally leading to a specific Reconstruction Quality Score (RQS indicator). Furthermore, the reliability of this score, depending on the number of measured points, can be established. This tool includes a function aiming at adjusting the speed for a further reconstruction and at defining the launching speed and the pulse shape for complementary sled tests. Finally, the functions of the RQS software and database are presented.
Data concerning accidents involving personal injury which have been collected in the context of in-depth investigations on scene in the Hannover area since 1973 and in the Dresden area since 1999 represent an important basis for empirical traffic safety research. At national and international level various analyses and comparisons are carried out on the basis of "in-depth data" from the above mentioned investigations. In-depth data play a decisive role e.g. within the validation of EuroNCAP results on secondary safety (crashworthiness) of individual passenger car models. Thus, statistically sound methods of data analysis and population parameter estimation are of high importance. Since the 1st of August 1984 the "in-depth investigations on scene" in the Hannover area have been carried out according to a sampling plan developed by HAUTZINGER in the context of a research project on behalf of BASt. In the meantime a second region of in-depth investigation on scene was added with surveys in Dresden and the surrounding area. Internationally, the acronym GIDAS (German In-Depth Accident Study) is commonly used for the two above mentioned surveys. The objective of a current research project (topic of this contribution) is, among other things, to examine and adjust the previous weighting and expansion method for the two regional accident investigations to the current general conditions.
In-depth road traffic accident research in Spain is a fairly recent activity. In the past, only accident data that had been retrospectively processed by the national and regional traffic police forces was available. In 1999 Applus+IDIADA set up a permanent accident research unit to carry out indepth analysis of road accidents in Spain. Since then accidents involving cars, motorcycles, coaches and vulnerable road users have been thoroughly studied. The Applus+IDIADA accident research team has carried out work for the various traffic polices in Spain and it is currently involved in several research projects in which accidentology is one of the main tasks. The working methodology of the team is presented in the first part of the paper. In the framework of the European research project "Rollover" (GRD2-2001-50086), Applus+IDIADA has collected data, inspected scenarios and performed virtual reconstructions of twenty-six of the total seventy-six rollover accidents studied. The second half of the paper describes how these accident investigations were used to develop a test procedure for identifying possible improvements to the vehicle structure which augment occupant protection in a rollover scenario. In particular, a proposal for a new drop test for rollover assessment is presented. The cases were analysed for severity, in terms of injury to the occupants and damage to the vehicle, and taking into account whether a seatbelt was worn or not. The worst possible cases were identified as those that had severe occupant injuries and sizable damage to the occupant compartment when seatbelts had been worn. The most severe cases were then analysed further for impact position (roll and pitch angles) and the impact velocity. With these parameters taken into account, the most representative combinations could be found. This resulted in a series of configurations for possible drop tests. The results of the tests indicate where passenger vehicle structures need to be improved in order to increase occupant safety in the event of a rollover crash.
Sedan type vehicles in which adult rear seat passengers were present and which were involved in frontal collisions were investigated, and the influence of unbelted rear seat passengers on the injuries of front seat occupants was studied. Unbelted rear seat passengers move forward during impact. It was observed that there were not only cases in which front seat occupants sustained injuries caused by direct contact with rear seat passengers, but also cases where front seat occupants received severe injuries due to additional force from rear seat passengers, either impacting directly or indirectly as a result of deformation of the front seat. Severe injuries of front seat occupants were observed in the latter cases. This research validates the importance of seat-belt use for rear seat passengers, not only to protect themselves but also to mitigate injuries of front seat occupants.
Interaction of road environment, vehicle and human factors in the causation of pedestrian accidents
(2005)
The UK On-the-Spot project (OTS) completed over 1500 in-depth investigations of road accidents during 2000-2003 and is continuing for a further 3 years. Cases were sampled from two regions of England using rotating shifts to cover all days of the week and all hours of the day and night. Research teams were dispatched to accidents notified to police during the shifts; arrival time to the scene of the accident was generally less than 20 minutes. The methodology of OTS includes sophisticated systems for describing accident causation and the interaction of road, vehicle and human factors. The purpose of this paper is to describe and illustrate these systems by reference to pedestrian accidents. This type of analysis is intended to provide an insight into how and why pedestrian accidents occur in order to assist the development of effective road, vehicle and behavioural countermeasures.
The European Union has set a target to reduce all road fatalities (over 40,000) with 50% in 2010. This target percentage remained unchanged with the introduction of the ten new member states within the EU as by May 1st, 2004. According to Eurostat, 34% of all fatalities in 1998 in the, then, fifteen states of the European Union were the result of single vehicle collisions. This represents over 14,000 lives lost each year of which many can likely be saved through better roadside infrastructure design. The challenge for road safety professionals is to find methods and design strategies that help to reduce these casualties. Procedures for full-scale vehicle crash testing of guard rails were first published in the US in 1962. Present European regulation is mainly based on these procedures and later developments. Since then the vehicle fleet has changed considerably. Due to the complexity of the actual safety problem the numerical simulation approach offers a good opportunity to evaluate the different parameters involved in road safety, such as infrastructure properties, vehicle type, vehicle occupants and injuries. The ideal situation would be that simulation tools are coupled or integrated and all involved effects would be related. At the moment this is not the case yet, but initiatives are taken and a new virtual era has started. This paper offers a method looking at two components that encompass the driving environment: the car and the guardrail. As part of the EC-funded project, RISER (Roadside Infrastructure for Safer European Roads) a multi body simulation program study is carried out to determine sensitivities of some parameters in car to guardrail collisions and gives insides in performance of the car with passive safety equipment, the guardrail and the interaction of these objects with each other. By offering a set of methods that includes these two aspects and their intertwining relations, more confidence can be gained in actually reducing fatalities due to single vehicle collisions with, or due to, roadside furniture. Reducing the number of fatalities of single vehicle crashes would contribute greatly to the stated goal of reducing casualties altogether.
In recent years the boundaries between active and passive safety blurred more and more. Passive safety in the traditional term includes all safety aspects to prevent occupants to be injured or at least injury severity should be reduced. Passive Safety starts with the collision (first vehicle contact) and ends with rescue (open vehicle doors). Within this phase the occupant has to be protected by the passenger compartment whereby no intrusion should occur. Active safety on the other side was developed to interact prior to the collision whereby the goal is to prevent accidents. The extensive interaction between active and passive safety led to the terminologies "Primary" and "Secondary" safety whereas the expression Integrated Safety Concept was generated. Within this study the most well documented single vehicle accidents with cars not equipped with ESP were identified from the PENDANT database and reconstructed. Additional cases were found in the database ZEDATU of TU Graz. In comparison each case was simulated with the assumption that the cars were equipped with ESP. The differences regarding accident avoidance or crash severity as well as reduction of injury risk were analysed.
Description of road traffic related knee injuries in published investigations is very heterogeneous. The purpose of this study was to estimate the risk of knee injuries in real world car impacts in Germany focusing vulnerable road users (pedestrians, bicyclists and motorcyclists) and restrained car drivers. The accident research unit analyses technical and medical data collected shortly after the accident at scene. Two different periods (years 1985-1993 and 1995-2003) were compared focusing on knee injuries (Abbreviated Injury Scale (AISKnee) 2/3). In order to determine the influences type of collision, direction and speed as well as the injury pattern and different injury scores (AIS, MAIS, ISS) were examined. 1.794 pedestrians, 742 motorcyclists, 2.728 bicyclists and 1.116 car drivers were extracted. 2% had serious ligamentous or bony injuries in relation to all injured. The risk of injury is higher for twowheelers than for pedestrians, but knee injury severity is higher for the latter group. Overall the current knee injury risk is low and significant reduced comparing both time periods (27%, p<0,0001). Severe injuries (AISKnee 2/3) were below 1%). Improved aerodynamic design of car fronts reduced the risk for severe knee injuries significantly (p=0,0015). Highest risk of injury is for motorcycle followed by pedestrians, respectively. Knee protectors could prevent injuries by reducing local forces. The classically described dashboard injury was rarely identified. The overall injury risk for knee injuries in road traffic is lower than estimated and reduced comparing both periods. The aerodynamic shape of current cars compared to older types reduced the incidence and severity of knee injuries. Further modification and optimization of the interior and exterior design could be a proper measurement. Classic described injury mechanisms were rarely identified. It seems that the AIS is still underestimating extremity injuries and their long term results.
Die Lastübertragung von den Fahrzeugrädern auf die Fahrbahntafel wird beschrieben, und es wird eine Übersicht der ermüdungsempfindlichen Schweissnahtbereiche von Deckblech, Längssteifen und Querträgern gegeben. Die charakteristischen Schwachpunkte der Schweissverbindungen werden in Skizzen dargestellt.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.
This paper describes the methodology for the assessment of the socio-economic impact of SAFESPOT applications. The applications selected for the assessment cover vehicle to vehicle (v2v) as well as vehicle to infrastructure (v2i) communication systems. The applications address main problem areas of road safety: accidents at intersections, accidents due to hazardous road and weather conditions and accidents due to over speeding and inappropriate distance. The assessment methodology relies in its core on cost-benefit analysis (CBA) as the most widespread tool to assess the profitability of applications form the society point of view. The assessment is however not limited to CBA but also considers the economic effects for particular stakeholder groups such as users, public authorities and the like. Their individual cost and benefits can be investigated in stakeholder analyses. Both elements, CBA and stakeholder analysis, form an integrated assessment approach which is applied here. The assessment makes use of the sound methodological base which was provided by projects such as SEiSS and eIMPACT. Some characteristics of co-operative systems however call for special attention within the assessment. Most prominently, the assessment will concentrate on a bundle of applications. The impact of this bundle will be assessed under the conditions of different business and service models. These issues will be addressed in the paper. Moreover, this paper also provides insight in likely patterns of results and first results of socio-economic impact assessment itself.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 15. Oktober 2009 in Baden-Baden ihr 7. Symposium \"Sicher fahren in Europa\". Nach 1991, 1994, 1997, 2000, 2003 und zuletzt 2006 trafen sich auch dieses Mal wieder zahlreiche Fachleute aus Wissenschaft und Politik, Industrie, Wirtschaft und Verbänden aus dem In- und Ausland, trugen neue Forschungsergebnisse vor und erörterten aktuelle Ansätze zur Erhöhung der Verkehrssicherheit. Dabei ging es in den Referaten und Diskussionsbeiträgen und in den vier Workshops vor allem darum, die verkehrspolitischen Entwicklungen und Herausforderungen für die europäische Verkehrssicherheitsarbeit im Hinblick auf folgende Themen zu beleuchten: "Verkehrssicherheit Junger Fahrer", - Das "Auto der Zukunft", - "Demographischer Wandel", - "Landstraßensicherheit". Den Grundsatzreferaten folgten vertiefte Bearbeitungen in den Workshops. Die CD-ROM dokumentiert die Grußworte, Referate und Diskussionsbeiträge.
In spite of today's highly sophisticated crash test procedures like the different NCAP programs running world-wide, bad real world crash performance of cars is still an issue. There are crash situations which are not sufficiently represented by actual test configurations. This is especially true for car to car, as well as for car to object impacts. The paper describes reasons for this bad performance. The reasons are in principal bad structural interaction between the car and its impact partners (geometric incompatibility), unadjusted front end stiffness (stiffness incompatibility) and collapse of passenger compartments. To show the efficiency of improving cars' structural behaviour in accidents with different impact partners an accident data analysis has been taken out by members of European Project VC-COMPAT. Accident data analysis has shown that in Germany between 15,000 and 20,000 of the now severely injured car occupants might get less injured and between 600 and 900 car occupant fatalities might be saved. Similar results arise for the UK.
In September 2004 the first international symposium called ESAR (Expert Symposium on Accident Research) was carried out at the University of Hannover (Germany). The idea for such international conference was to bring together experts from the fields of accident investigation teams worldwide to present their results for a common audience of people from government, industry and other universities. The first conference was a really sufficient one and followed by the second symposium also at the Hannover Medical School two years later in 2006. This two year rhythm was now continued with the third conference in Hannover again in 2008. It is planned to carry out ESAR every two years also in the future. ESAR is a scientific colloquium and can be seen as a platform for exchange of information on accident research issues based on methodologies of investigation, injury mechanisms and injury assessment, accident causation and other issues of statistical accident data analysis. Representatives from authorities as well as from medical and technical institutions come together to discuss new research issues and exchange experiences on accident prevention and the complex field of accident reconstruction. Special focus was given to the target the European Union set for itself in 2000 which stipulates that within 10 years the number of person killed in road traffic accidents must be cut in half. To reach this goal, optimized measures, comprehensive research and analysis are necessary. A key hurdle comes from the European Union extension to 27 member states, each featuring different levels of traffic safety standards and different accident scenarios. Existing results from long term research projects in Europe, the USA, Australia and Japan including analyses of infrastructure, population, vehicle fleet and driver behaviour offer an excellent basis for understanding and improving countermeasures and research support needs in underdeveloped countries. ESAR's goal is to bring together researchers from all parts of the world, who will report on their methods and recommendations to improve traffic safety based on "In-Depth-Investigations" of real world accidents. These In-depth-investigations of accidents require thorough documentation and an accident data analysis on multidisciplinary levels which must be carried out immediately after it occurs. ESAR presents scientists the opportunity to present their studies on a common basis of research level.
In recent years considerable progress in active and passive safety of road vehicles has been made. The road traffic of today is much safer than in the past. A current vehicle has a lot more safety elements resulting in an improved inner and outer technique. In most European countries the number of fatalities is decreasing despite growing traffic and road usage. Nevertheless, the number of casualties in road traffic accidents is high enough, thus more progress is needed if the number of fatalities is to be reduced by 50%, as postulated by the European Commission for the year 2010. In order to develop countermeasures and further possibilities for injury prevention, it is increasingly important to have accident data available, supplying results quickly and giving the best overview across Europe. In-Depth-Data Sampling Procedures have a huge historical development, starting in the 60ies by the car manufactures, continued during the 70ies mostly by some universities mainly in England, Sweden, France and Germany, today a net of in-depth-investigation teams are working across Europe and around the world.One of the oldest teams is located at the Hannover Medical School, founded in 1973 by the German Government on behalf of the Federal Highway Research Institute Bast. It was the only team worldwide that was equipped with blue light emergency cars, working on scene in time so directly after the event and working continuously during the years, collecting 20 thousand accidents within 30 years period. Since 1999 the order is carried out in cooperation with the German car industry, which is interested and has benefit on the data too. On the basis of the new data collection, so called GIDAS (German In-Depth Accident Study), that has been run at the Technical University Dresden and the Medical University Hannover), a special tool for In-Depth-Accident Analysis was founded. It is the task of this conference to build a platform for such research based on In-Depth-Investigation. The conference is specially aimed at the area of accident data analysis in order to contribute to the harmonization of different investigation methods and accumulation of different results that does exist for different countries worldwide. Up to now no special conference did exist to deal with accident data only following in the discussion for an improvement in traffic and vehicle safety. ESAR - expert symposium on accident research - should be a step forward. This first international conference is being organized by the Accident Research Unit at the Medical University Hannover jointly with the German Federal Highway Research Institute Bast and the Research Association of German Car Manufacturers FAT. The conference should be a platform for an interdisciplinary exchange of information based on the different presentations from participants around the world.
Zum gegenwärtigen Zeitpunkt werden verschiedene Ansätze diskutiert, wie der Verbesserung der Straßenverkehrssicherheit durch den Einsatz moderner Fahrerassistenzsysteme (FAS) neue Impulse gegeben werden können. Unter dem Dach der von der Europäischen Kommission gemeinsam mit der Industrie im Frühjahr 2002 ins Leben gerufenen eSafety-Initiative soll die Entwicklung und Implementierung "Intelligenter Integrierter Sicherheitssysteme" (Intelligent Integrated Road Safety Systems) koordiniert und vorangetrieben werden. Erwartet werden hiervon entscheidende Beiträge zur Erreichung der bis zum Jahr 2010 angestrebten Halbierung der Zahl der Verkehrstoten in Europa, entsprechend dem Weissbuch der Europäischen Kommission. Intelligente Unterstützung des Fahrers meint in diesem Zusammenhang die Berücksichtigung des Gesamtsystems "Fahrer-Fahrzeug-Umwelt". Für die fahrzeugseitige Umsetzung der Unterstützungsfunktion wurden verschiedene Ausformungsgrade (zum Beispiel Information, Warnung, korrigierender Eingriff) vorgeschlagen und entwickelt. Die BASt ist an einer Reihe von Projekten und Arbeitsgruppen beteiligt, die sich direkt oder indirekt mit Fragen befassen, die sich bei der Entwicklung und Bewertung intelligenter FAS zur Beeinflussung der Fahrzeuggeschwindigkeit stellen. Im Mittelpunkt stehen dabei vor allem Fragen der Sicherheitsbewertung und der Machbarkeit, wie zum Beispiel - Realisierung der fahrzeugseitigen Umsetzung, - Kosten-Nutzen-Gesichtspunkte, - Rechtliche Aspekte, - Voraussetzungen der Datenbasis. Beispielsweise ist die BASt an der von ERTICO koordinierten "SpeedAlert"-Initiative beteiligt. Ziel dieser Aktivität ist die europaweite Implementierung eines Geschwindigkeitswarnsystems. An der hierzu im Jahre 2001 gegründeten "SpeedAlert" Arbeitsgruppe beteiligen sich Industrie und Verwaltung.
Der Allgemeine Deutsche Automobilclub e. V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 7. und 8. Oktober 2003 in Wiesbaden ihr 5. Symposium "Sicher fahren in Europa". Nach 1991, 1994, 1997 und 2000 trafen sich erneut über 200 Fachleute aus Wissenschaft, Politik, Verwaltung, Industrie, Wirtschaft und Verbänden aus ganz Europa und einigen außereuropäischen Ländern, trugen neue Forschungsergebnisse vor und erörterten aktuelle Ansätze zur Erhöhung der Sicherheit im Straßenverkehr. Dabei ging es in Vortrags- und Diskussionsbeiträgen vor allem darum, folgende verkehrspolitischen Herausforderungen und Entwicklungen für eine europaweite Verkehrssicherheitsarbeit zu beleuchten: - die Umsetzung des 3. Verkehrssicherheits-Aktionsprogrammes der EU-Kommission bis 2010, dessen Diskussion gerade begonnen hat, - die zusätzlichen Probleme und Herausforderungen für die Verkehrssicherheit, die ab 2004 durch den EU-Beitritt von 10 weiteren Mitgliedsländern entstehen, - das Bestreben vieler EU-Mitgliedsstaaten, ihre nationale Identität und ihre regionalen Besonderheiten auch auf dem Gebiet der Verkehrssicherheit zu bewahren, um die Akzeptanz und Effizienz von praktischen Maßnahmen zu sichern, ein Ziel, dem sich auch der "EU-Konvent zur Zukunft Europas" verschrieben hat. Diesen ebenso aktuellen wie grundsätzlichen Anforderungen entsprach das Veranstaltungsprogramm mit seinen verkehrspolitischen Eröffnungs-vorträgen und mit drei Fachsitzungen - zur Verbesserung der Fahrzeugsicherheit, - der Verbesserung der Straßensicherheit und - zur Verbesserung des Verhaltens von Verkehrsteilnehmern. Eine Podiumsdiskussion "Zur Harmonisierung von Verkehrsüberwachung und Sanktionen" schloss die Veranstaltung ab.