Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (404) (entfernen)
Schlagworte
- Conference (324)
- Konferenz (320)
- Germany (151)
- Accident (150)
- Unfall (150)
- Deutschland (149)
- Injury (101)
- Verletzung (100)
- Unfallrekonstruktion (81)
- Analyse (math) (64)
Small overlap frontal crashes are defined by a damage pattern with most of the vehicle deformation concentrated outboard of the main longitudinal structures. These crashes are prominent among frontal crashes resulting in serious and fatal injuries, even among vehicles that perform well in regulatory and consumer information crash tests. One of the critical aspects of understanding these crashes is knowing the crash speeds that cause the types of damage associated with serious injuries. Laboratory crash tests were conducted using 12 vehicles in three small overlap test conditions: pole, vehicle-to-vehicle collinear, and vehicle-to-vehicle oblique (15-degree striking angle). Field reconstruction techniques were used to estimate the delta V for each vehicle, and these results were compared with actual delta V values based on vehicle accelerometer data. Estimated delta Vs were 50% lower than actual values. Velocity change estimates for small overlap frontal crashes in databases such as NASS-CDS significantly underestimate actual values.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
Causation patterns and data collection blind spots for fatal intersection accidents in Norway
(2010)
Norwegian fatal intersection accidents from the years 2005-2007 were analysed to identify any causation patterns among their underlying contributing factors, and also to evaluate whether the data collection and documentation procedures used by the Norwegian in-depth investigation teams produces the information necessary to perform causation pattern analysis. A total of 28 fatal accidents were analysed. Details on crash contributing factors for each driver in each crash were first coded using the Driving Reliability and Error Analysis Method (DREAM), and then aggregated based on whether the driver was going straight or turning. Analysis results indicate that turning drivers to a large extent are faced with perception difficulties and unexpected behaviour from the primary conflict vehicle, while at the same time trying to negotiate a demanding traffic situation. Drivers going straight on the other hand have less perception difficulties. Instead, their main problem is that they largely expect turning drivers to yield. When this assumption is violated, they are either slow to react or do not react at all. Contributing factors often pointed to in literature, e.g. high speed, drugs and/or alcohol and inadequate driver training, played a role in 12 of 28 accidents. While this confirms their prevalence, it also indicates that most drivers end up in these situations due to combinations of less auspicious contributing factors. In terms of data collection and documentation, information on blunt end factors (those more distant in time/space, yet important for the development of events) was more limited than information on sharp end factors (those close in time/space to the crash). A possible explanation is that analysts may view some blunt end factors as event circumstances rather than contributing factors in themselves, and therefore do not report them. There was also an asymmetry in terms of reported obstructions to view due to signposts and vegetation. While frequently reported as contributing for turning drivers, they were rarely reported as contributing for their counterparts in the same accidents. This probably reflects an involuntary focus of the analyst on identifying contributing factors for the driver legally held liable, while less attention is paid to the driver judged not at fault. Since who to blame often is irrelevant from a countermeasure development point of view, this underlying investigator mindset needs addressing to avoid future bias in crash investigation reports.
Providing effective occupant protection in rollover crashes requires supplying the occupant with a restraint system proven effective in the dynamic rollover accident mode. Preventing ejection and providing restraint sufficient to prevent potentially injurious contacts with both interior and exterior vehicle components is paramount for effective rollover occupant protection. Research has shown that the injury potential can be decreased by closely coupling the occupant to the seat. This paper focuses on the effect of restraint system slack and its relationship to occupant excursion and ejection potential during rollover. Various restraint system configurations are evaluated in rollover-type test environments. A review of prior research is presented prior to presenting new quasi-static vehicle inversion studies conducted with live surrogate occupants. Additionally, dynamic rollover testing utilizing anthropometric test devices (ATDs) is presented. The influence of belt looseness and effects of various restraint designs on the belted occupants' injury potential are discussed.
In road traffic accidents, a car-seat and its occupant can be subjected to various crash pulses in the case of a rear impact. This study investigates the influence of crash pulse shape on seat-occupant response and evaluates the corresponding risk of whiplash injury. For this purpose, a rigorously validated seat-occupant system model is used to study different carseat designs and crash pulses. Two different car-seat concepts are also presented which can effectively mitigate whiplash injury for a wide range of crash severity. It is shown that for crash pulses of similar severity, the level of whiplash-risk depends strongly on the combined effects of seat design and crash pulse shape.
Although the statistics show a decreasing rate of child injuries and fatalities in German road accidents more efforts can be made to protect children in cars e.g. by developing appropriate child restraint systems. An important part in of this work can be achieved with the help of crash tests using child dummies. However these crash tests cannot completely reflect the situation of real world crashes as factors like children moving out of the optimal position or children incorrectly fastened by their parents are difficult to predict. Therefore this study gives an overview over the current accident and injury situation of child occupants in cars in German road accidents.
Recent findings from real-world accident data have shown that fatality risks for pedestrians are substantially lower than generally reported in the traffic safety literature. One of the keys to this insight has been the large and random sample of car-to-pedestrian crashes available in the German In-Depth Accident Study (GIDAS). Another key factor has been the proper use of weight factors in order to adjust for outcome-based sampling bias in the accident data. However, a third factor, a priori of unknown importance, has not yet been properly analysed. This is the influence of errors in impact speed estimation. In this study, we derived a statistical model of the impact speed errors for pedestrian accidents present in the GIDAS database. The error model was then applied to investigate the effect of the estimation error on the pedestrian fatality risk as a function of car impact speed. To this end, we applied a method known as the SIMulation-EXtrapolation (SIMEX) method. It was found that the risk curve is fairly tolerant to some amount of random measurement error, but that it does become flattened. It is therefore important that the accident investigations and reconstructions are of high quality to assure that systematic errors are minimised and that the random errors are under control.
The NHTSA-sponsored Crash Injury Research and Engineering Network (CIREN) has collected and analyzed crash, vehicle damage, and detailed injury data from over 4000 case occupants who were patients admitted to Level-I trauma centers following involvement in motor vehicle crashes. Since 2005, CIREN has used a methodology known as "BioTab" to analyze and document the causes of injuries resulting from passenger vehicle crashes. BioTab was developed to provide a complete evidenced-based method to describe and document injury causation from in-depth crash investigations with confidence levels assigned to the causes of injury based on the available evidence. This paper describes how the BioTab method is being used in CIREN to leverage the data collected from in-depth crash investigations, and particularly the detailed injury data available in CIREN, to develop evidence-based assessments of injury causation. CIREN case examples are provided to demonstrate the ability of the BioTab method to improve real-world crash/injury data assessment.
Bone fracture patterns could be crucial in reconstructing the nature of loading, especially in the lower limb and upper limb kinematics in vehicle-pedestrian crashes. In addition, use of FE bone models can be a handy tool to predict vehicle impact velocity and the impact direction. The point of fracture initiation in bone loading has been predicted quite accurately earlier. A methodology that predicts bone crack initiation and its propagation pattern for the six known loading directions using a single material and failure model is presented.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
Brücken in ungünstiger geographischer/geomorphologischer Lage " z.B. über Gewässer, in Einschnitten, Schattenlagen und Niederungsbereichen " neigen konstruktionsbedingt gegenüber den angrenzenden bodengebundenen Fahrbahnen zur vorzeitigen Glättebildung, die eine besondere Gefährdung der Verkehrsteilnehmer - vor allem im Spätherbst und im zeitigen Frühjahr - darstellt. Die Erneuerung der Straßenbrücke B 208 / Elbe-Lübeck-Kanal in der Ortslage Berkenthin im Kreis Herzogtum Lauenburg bot auf Grund ihrer besonderen kleinklimatischen Situation die Möglichkeit, im Rahmen eines Pilotprojektes - aufbauend auf den Ergebnissen des Forschungsprojektes 15.401 "Vermeidung von Glatteisbildung auf Brücken" der BASt " die Fahrbahntafel mittels oberflächennaher geothermischer Energie zu temperieren. Die bei Planung, Bau sowie in der nunmehr anlaufenden Nutzungsphase gewonnenen Erkenntnisse sollen den Straßenbaulastträgern Hinweise und Entscheidungshilfen geben, die Verkehrssicherheit wie auch die Nachhaltigkeit bei glättegefährdeten Brücken und Straßenabschnitten durch den Einsatz alternativer Energien zu erhöhen und gleichzeitig den Aufwand für den präventiven Winterdienst zu reduzieren. Der hierfür erforderliche Kapitaleinsatz ist eher in volkswirtschaftlicher Hinsicht und erst in zweiter Linie betriebswirtschaftlich zu bewerten.
Im Rahmen eines von der Bundesanstalt für Straßenwesen (BASt) initiierten Forschungsvorhabens (15.449/2007/ERB: "Prüfverfahren zur Beurteilung der Lebensdauer von Kunststoffdichtungsbahnen für Straßentunnel") wurden anhand von Untersuchungen an Kunststoffdichtungsbahnen (KDB) auf Basis von Polyolefinwerkstoffen die Möglichkeiten der Beurteilung der oxidativen Langzeitbeständigkeit sondiert. Im Mittelpunkt stand die Erprobung des Autoklaventests in Anlehnung an DIN EN ISO 13438 (Methode C1/C2) an ausgewählten, für den Tunnelbau repräsentativen marktüblichen KDB-Produkten. Die Untersuchungen im Autoklaven bei erhöhten Temperaturen (60 -°C, 70 -°C und 80 -°C) und Sauerstoffdrücken (11, 21 und 51 bar) wurden durch vergleichende Versuche im Wärmeschrank (Ofen) bei erhöhter Temperatur (85 -°C) in Anlehnung an DIN EN 14575 ergänzt. Die KDB-Produkte wurden außerdem einer eingehenden Materialcharakterisierung (Zugprüfung, OMA, DSC) unterzogen. Weiterhin wurden Bauwerksdaten recherchiert und auf ihre Nutzbarkeit zur Bewertung und Prüfbarkeit der Langzeitbeständigkeit von KDB in Tunneln betrachtet. Ziel war auch, die Anwendbarkeit des bisher vorgeschlagenen Extrapolationsmodells zur Auswertung der Ergebnisse von Autoklaventests an im Tunnelbau marktüblichen Produkten für Nutzungsdauern über 25 Jahre zu überprüfen und zur Entwicklung eines geeigneten Prüfverfahrens beizutragen. Der Beitrag geht auf Ergebnisse des Vorhabens ein und zeigt erste Schlussfolgerungen und weiteren Untersuchungsbedarf auf. Die Ergebnisse werden in den "Empfehlungen zu Dichtungssystemen im Tunnelbau EAG-EDT" des Arbeitskreises 5.1 "Kunststoffe in der Geotechnik und im Wasserbau" berücksichtigt, deren 2. Auflage in Vorbereitung ist. Aspekte des thermischen Verhaltens der eingesetzten Werkstoffe sowie mögliche Anpassungen der Prüfrandbedingungen für die Autoklaventests werden ergänzt und Hinweise zur Interpretation von Prüfergebnissen gegeben. Außerdem wurden inzwischen ausgehend von den Ergebnissen des Forschungsvorhabens erste Autoklaven-Ringversuche in drei Prüfinstitutionen initiiert.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Kategorie-1-Schäden bei orthotropen Fahrbahnplatten treten als bauweisenunabhängige Schäden in Form von Rissen im Anschlussbereich Deckblech-Längsrippe auf. Zur Vermeidung dieser Schäden sind geeignete Instandsetzungsmaßnahmen zu entwickeln, die zu einer Verminderung der Spannungen und Durchbiegungen in den gefährdeten Bereichen führen. Im Rahmen eines aktuellen Forschungsvorhabens an der Universität Duisburg-Essen wird der Ansatz verfolgt, einen modifizierten Fahrbahnbelag bestehend aus einem mit Epoxydharz oder alternativ mit Bioharz verfüllten Asphalttraggerüsts mit erhöhter mittragender Wirkung einzusetzen. Des Weiteren wird im vorliegenden Beitrag der Einsatz von Betonfertigteilen aus UHPC erläutert.
Im Jahr 2005 wurde mit dem Bau der Niederrheinbrücke Wesel der Bau der Ortsumgehung Wesel begonnen. Der Beitrag berichtet über einige Ausführungsdetails der im Jahr 2009 fertiggestellten Baumaßnahme: die Herstellung des Pylons in hochfestem Beton, die Montage der Strombrücke, der Einsatz von Parallellitzenbündeln.
W.-D. FRIEDRICH schildert in seinem Einführungsvortrag die praktischen Erfahrungen und Probleme der DEGES Deutsche Einheit, Fernstraßenplanungs- und -bau GmbH beim straßenrechtlichen Grunderwerb. Die DEGES ist dazu übergegangen, den Grunderwerb unter Einbeziehung von Dienstleistungsfirmen zu realisieren, was sich als effizient, kostengünstig und flexibel erwiesen hat. Im Zuge der Vorbereitung und Durchführung von Besitzeinweisungsverfahren bilden namentlich der Nachweis der Dringlichkeit und die Besitzeinweisung für Ausgleichs- und Ersatzmaßnahmen Problemschwerpunkte. Im Zentrum der Rechtsstreitigkeiten der eigentlichen Enteignungsverfahren steht die Verkehrswertermittlung, wobei FRIEDRICH beispielhaft die Bewertung von Grundstücken, in denen bergfreie Bodenschätze lagern, und die kontrovers umstrittene Frage der Berücksichtigung von Betriebsprämien als gesicherte Rechtsposition diskutiert. E. ALLESCH berichtet über aktuelle Rechtsfragen der straßenrechtlichen Enteignung, die sich aus Sicht der Verwaltungsgerichtsbarkeit stellen. Er verdeutlicht das Zusammenspiel der Vorschriften des Bundesfernstraßengesetzes (-§ 18f, -§ 19 FStrG) mit dem Enteignungsrecht der Länder und behandelt als Einzelprobleme unter anderem die Probleme der Enteignung und Besitzeinweisung auf Grundlage eines isolierten Straßenbebauungsplans, die Fragen der Wirksamkeit und Durchsetzbarkeit einer Einigung in und ausserhalb des Enteignungsverfahrens, das Erfordernis des sofortigen Baubeginns im Sinne des -§ 18f Abs. 1 Satz 1 FStrG und die Frage nach dem Ausschluss "weiterer Voraussetzungen" nach -§ 18f Abs. 1 Satz 3 FStrG. H. SCHMITZ liefert einen Bericht zum Stand der geplanten Vereinheitlichung der Fachplanungsgesetze im Verwaltungsverfahrensgesetz, die insbesondere auf eine Verallgemeinerung der Regelungen des Infrastrukturplanungsbeschleunigungsgesetzes abzielt. Er stellt dabei namentlich den Inhalt des Musterentwurfs der Verwaltungsverfahrensrechtsreferenten von Bund und Ländern mit den letzten Fortschreibungen vor. T. TEGTBAUER beschreibt in ihrem Beitrag zur "Privatisierung im Straßenbau" die aktuellen Erfahrungen des Bundes mit dem sog. A-Modell. Einer Darstellung des Konzepts selbst folgen eine Chronologie der Entwicklung der A-Modelle, eine Vorstellung der vier A-Modell-Pilotprojekte sowie des strukturierten Verhandlungsverfahrens und insbesondere der Wirtschaftlichkeitsuntersuchung i. S. v. -§ 7 BHO. Die Auswertung der vier Pilotprojekte ergab, dass die selbst gesteckten Ziele mit den Pilotprojekten teilweise erreicht wurden, weshalb der Bund mit den Ländern bereits acht weitere Projekte abstimmen konnte. G. RECKER vervollständigt dieses Bild aus Sicht eines Landes und berichtet über die Grundsanierung und den erforderlichen Ausbau auf sechs Streifen eines Streckenabschnitts der BAB 1, die die stark befahrenen Strecken von Schleswig-Holstein bis Saarbrücken und die Seehäfen Norddeutschlands mit dem Westen Deutschlands verbindet und Teil der transeuropäischen Netze ist. Im Ergebnis ist der Aufwand für das gebündelte Vergabeverfahren im Vergleich zur Durchführung von sieben Einzelverfahren geringer ausgefallen, wobei weitere Synergieeffekte als möglich angesehen werden. Allerdings ist gerade in der Umsetzungsphase auch auf Seiten des Konzessionsnehmers noch die erforderliche Routine auszubauen.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
Herber diskutiert angesichts des Auseinanderklaffens einerseits der aktuellen Verkehrsprognosen " die namentlich auf den Autobahnen von 2004 bis 2025 Verkehrszuwächse von 44 % veranschlagen " und andererseits der finanziellen und ökologischen Begrenzungen der künftigen Verkehrspolitik verschiedene Vorschläge zur Reform der Bundesauftragsverwaltung, der Netzplanung, der Netzbereinigung und der Netzbildung sowie zur besseren Einbindung der Bürger in die Planungsverfahren von Straßeninfrastrukturprojekten. Geigers Beitrag zum planfeststellenden Bebauungsplan gelangt zu einem skeptischen Befund: Nach seiner Einschätzung sprechen insgesamt überwiegende Gründe dafür, Straßenbauvorhaben regelmäßig durch Planfeststellung und nicht durch planfeststellungsersetzenden Bebauungsplan festzusetzen. Insbesondere von dem Instrument des isolierten Straßenbebauungsplans solle nur in Ausnahmefällen Gebrauch gemacht werden. Selbst im Gesamtkontext einer umfassenden städtebaulichen Umgestaltung empfehle sich meist eine zeitlich und inhaltlich aufeinander abgestimmte Planung, bei der sich die Gemeinde auf die städtebaulichen Planungen beschränke und die straßenseitige Planung der Straßenbauverwaltung überlasse. Der Beitrag zu "notwendigen Folgemaßnahmen" von Gaentzsch diagnostiziert trotz einer ganzen Reihe einschlägiger Präjudizen weiterhin erhebliche Rechtsunsicherheiten bei der Anwendung des -§ 75 Absatz 1 Satz 1 und des -§ 78 VwVfG. Skeptisch äußert sich Gaentzsch gegenüber dem Versuch, die Voraussetzungen beider Regelungen weiter gesetzlich zu konkretisieren. Er empfiehlt stattdessen, in Zweifels- oder Streitfällen die gemeinsame oberste Behörde entscheiden zu lassen und zudem die Fehlerfolgenregelung des -§ 75 Absatz 1a VwVfG auch auf Fehler im Bereich der Folgemaßnahmen auszuweiten. Der abschließende Beitrag von Sauthoff zur "Abstufung nicht mehr fernverkehrsrelevanter Bundesfernstraßen" widmet sich einem zentralen verfassungsrechtlichen Streitpunkt des Straßenrechts der letzten Jahrzehnte. Er diskutiert neuere gutachtliche Ausarbeitungen zur Überprüfung des Bundesfernstraßennetzes, die er als Verhandlungsgrundlage zwischen Bund und Ländern ansieht. Die in den Richtlinien für integrierte Netzgestaltung (RIN) vorgesehene Anknüpfung an das raumordnerische Zentrale"Orte"System bei der Klassifizierung des Straßennetzes sei jedoch nur mit Modifikationen möglich; rechtlich entscheidend seien allein die verfassungsrechtlich fundierten Kriterien des -§ 1 Absatz 1 FStrG und damit letztlich die " gegebenenfalls geänderte " Verkehrsbedeutung der Straße. Bei Anwendung dieser Maßstäbe sei grundsätzlich auch eine Weisung des Bundes auf Einziehung zulässig. Einen Bedarf für eine Novellierung des Bundesfernstraßengesetzes verneint der Referent.
In 2012 the fifth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
The utilisation of secondary-safety systems to protect occupants has attained a very high level over the past decades. Further improvements are still possible, but increasingly minor progress is only to be had with a high degree of effort. Thus, a key aspect must be the impact to overall safety in an accident. If reliable information is available on an imminent crash, measures already taken in the pre-crash phase can result in a significantly great influence on the outcomes of the crash. With this background preventive measures are the key to a sustainable further reduction of the figures of crash victims on our roads. This paper aims to show a preventive approach that can contribute to lessening the consequences of a crash by creating an optimum interaction of measures in the fields of primary and secondary safety. To further enhance vehicle safety, driver assistant systems are already available that warn the driver of an imminent front-to-rear-end crash. The next step is to support him in his reactions or if he fails to react sufficiently, to even initiate an automatic braking when the crash becomes unavoidable. Automatic pre-crash braking can, in an ideal situation, fully prevent a crash or can significantly reduce the impact speed and thus the impact energy (and the severity of the accident). If a vehicle is being braked in the pre-crash phase, the occupants are already being pre-stressed by the deceleration. The information available about the imminent crash can be used to activate the belt tensioners and likewise other secondary safety systems in the vehicle right before the impact. The pre-crash deceleration also causes the front of the vehicle to dip. Conventional crash tests do not take this specific impact situation into consideration. This is why, for example, the influences of the pre-crash displacements of the occupants are not recorded in the test results. Furthermore, a reproducible representation of the benefit of the vehicle safety systems which prepare the occupants for the imminent impact is not possible. In order to demonstrate the functions of automated pre-crash braking and to investigate the differences during the impact as a consequence of the altered occupant positions as well as the initiation of force and deformations of the vehicle front, DEKRA teamed up with BMW to carry out a joint crash test with the latest BMW 5 series vehicle. It involved the vehicle braking automatically from a starting test speed of 64 km/h (corresponding to the impact speed set by Euro NCAP) down to 40 km/h. The test was still run by the intelligent drive system of the crash test facility. This required several modifications to be made to the test facility as well as to the vehicle. The paper will describe and discuss some relevant results of the crash test. In addition, the possible benefits of such systems will also be considered. The test supplemented the work of the vFSS working group (vFSS stands advanced Forward-looking Safety Systems).
From literature well-known analyzes on risks, hazards and causes of accidents of older drivers are amended by the present study in which a comparison of the specific features of accident causes of older car drivers (older than 60 years) and of younger car drivers (under 25 years) is conducted. Mainly the question is pursued if specific errors, mistakes and lapses are predominant in the two different age groups. The analysis system ACAS (Accident Causation Analysis System) used hereby consists of a sequential system of accident causation factors from the human, the technical and the infrastructural field, whereupon for this study the influence of the human features on the accident development in two different age groups is of interest. ACAS is both an accident model and an analysis and classification system, which describes the human participation factors of an accident and their causes in the temporal sequence (from the perceptibility to concrete action errors) taking into consideration the logical sequence of individual basic functions. In five steps (categories) of a logical and temporal sequence the hierarchical system makes human functions and processes as determinants of accident causes identifiable. The methodology specifically focuses on the use in so-called "In-Depth" and "On-Scene" investigation studies. With the help of the system for each accident participant one or more of five hypotheses of human cause factors are formed and then specified by appropriate verification criteria. These hypotheses in turn are further specified by indicators in such manner that the coding of the causation factors by a code system meets the needs of database processing and are accessible to a quantitative data analysis. The first results of the descriptive comparison of the two age groups concern mainly differences in the functional levels "information admission/perception" (where the elderly drivers have more difficulties than the young ones) and "information processing/evaluation" (where the younger drivers show more problems). Concerning the cognitive function of "planning" the group of younger drivers seems to be more often involved in an accident because of excessive speed.
Real world accident reconstruction with the Total Human Model for Safety (THUMS) in Pam-Crash
(2013)
Further improvement of vehicle safety needs detailed analysis of real world accidents. According to GIDAS (German In-Depth Accident Study) most car to car front accidents occur at mid-crash severity. In this range thoracic injuries already occur. In this study a real world frontal crash with mid-crash severity out of the AARU database was reconstructed. The selected car to car accident was reconstructed by AARU by means of pc-crash software in order to get the initial dynamic accident conditions. These initial conditions were used to reconstruct the complete accident in more detail using FE models for the car structure and the occupants. Occupant simulations were performed with FE HIII-dummy models and the THUMS using Pam-Crash code. An initial THUMS validation was performed in order to verify the model-´s biofidelity by means of table-top test simulations. THUMS bone stiffness values were modified to match the real word occupant age. A comparison between driver and passenger restraint system loading was done, as well as an injury prediction comparison between the HIII-dummy model and THUMS response for both cases. Detailed comparison between the HIII-dummy models and THUMS regarding thoracic loading are discussed.
In der Vergangenheit stiegen die Verkehrsbelastung und der Anteil des Schwerverkehrs auf deutschen Straßen und Autobahnen nahezu stetig. Dies wird sich auch in der Zukunft fortsetzen. Um auch zukünftig Mobilität gewährleisten zu können, sind Bauweisen mit maximaler Nutzungsdauer und minimalen Erhaltungsaufwendungen erforderlich. In Deutschland werden Betonfahrbahndecken als unbewehrte direkt befahrene Betonfahrbahnplatten mit Querfugen in regelmäßigen Abständen gefertigt und für Nutzungsdauern von 30 Jahren konzipiert. Die Querfugen stellen dabei den schwächsten Bereich in der Konstruktion dar. Betonfahrbahndecken können auch als Durchgehend Bewehrte Betonfahrbahndecke gefertigt werden. Dabei stellt sich ein freies Rissbild mit schmalen Plattenstreifen ein. Um eine Querkraftübertragung zu sichern, wird die Rissöffnungsweite durch die Anordnung einer durchgehenden Längsbewehrung beschränkt. Die Erfahrungen zeigen, dass mit dieser Bauweise eine längere Nutzungsdauer und ein höherer Fahrkomfort erreicht werden und weniger Erhaltungsmaßnahmen erforderlich sind. Durchgehend Bewehrte Betondecken eignen sich besonders gut für eine Asphaltüberbauung, da es keine Querfugen als Störstellen gibt. Diese Komposition hat das Potenzial für eine Nutzungsdauer von 50 Jahren und erfordert geringere Kosten, wenn man den gesamten Lebenszyklus betrachtet. Um baupraktische Erfahrungen zu sammeln, wurde im Jahr 2011 auf der Bundesautobahn (BAB) A 94 bei Forstinning in Bayern eine Versuchsstrecke eingerichtet. Diese besteht aus drei Abschnitten von je etwa 4 km Länge: Durchgehend Bewehrte Betondecke mit DSH-V-Überbauung, unbewehrte Betondecke in Plattenbauweise mit DSH-V-Überbauung und unbewehrte Betondecke in Plattenbauweise mit Grinding-Oberfläche. Erste Ergebnisse bezüglich Rissbildung, Bewegungen an den Endspornen, Haftverhalten des Blacktopping und der Schallmessungen liegen vor.
Die neuen TL/ZTV/TP Fug-StB
(2013)
Eine Betondecke kann nur so gut sein wie ihre Fugen und Fugenfüllsysteme. Funktionierende Fugen sind daher ein wesentlicher Bestandteil der Betonstraße. Nur mit funktionierendem Fugenfüllsystem kann die prognostizierte Lebensdauer einer Betondecke von mindestens 30 Jahren erreicht werden. In diesem Sinne wurden im Jahre 2001 die ZTV Fug-StB 01) eingeführt, um durch technische Vorgaben einen hohen Standard bei der Herstellung von Fugen zu gewährleisten. Aufgrund notwendiger Neuerungen, technischer Weiterentwicklung bei der Herstellung von Fugenmassen und -profilen sowie der Umsetzung der Europäischen Normen in das Deutsche Regelwerk war nach 10 Jahren nun eine Überarbeitung notwendig. Der Entwurf der neuen ZTV Fug-StB gliedert sich nach dem Kapitel "Allgemeines" in vier Teile für die unterschiedlichen Fugenfüllsysteme. Die neuen ZTV Fug-StB sind für Beton- und Asphaltflächen ebenso wie für Verkehrsflächen auf Bauwerken, Pflasterflächen, Schienenfugen und Riss-Sanierungen anwendbar. Es werden neu entwickelte Fugenkonstruktionen behandelt. Die Bedeutung funktionierender Fugen und Fugenfüllsysteme wird anhand aktueller Themen sehr deutlich. Derzeit werden verstärkt Schäden bei Fugen an neuen Betondecken, insbesondere Flankenablösungen und Versprödungen der Fugenvergussmasse beobachtet. Hier werden mögliche Schadensursachen ermittelt mit dem Ziel, über die komplexen Wirkungszusammenhänge ein Fugenfüllsystem mit Heißvergussmassen zu entwickeln, das den technischen Anforderungen an das Gesamtsystem "Betonstraße" gerecht wird.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
In general the passive safety capability is much greater in newer versus older cars due to the stiff compartment preventing intrusion in severe collisions. However, the stiffer structure which increases the deceleration can lead to a change in injury patterns. In order to analyse possible injury mechanisms for thoracic and lumbar spine injuries, data from the German Inâ€Depth Accident Study (GIDAS) were used in this study. A twoâ€step approach of statistical and caseâ€byâ€case analysis was applied for this investigation. In total 4,289 collisions were selected involving 8,844 vehicles, 5,765 injured persons and 9,468 coded injuries. Thoracic and lumbar spine injuries such as burst, compression or dislocation fractures as well as soft tissue injuries were found to occur in frontal impacts even without intrusion to the passenger compartment. If a MAIS 2+ injury occurred, in 15% of the cases a thoracic and/or lumbar spine injury is included. Considering AIS 2+ thoracic and lumbar spine, most injuries were fractures and occurred in the lumbar spine area. From the case by case analyses it can be concluded that lumbar spine fractures occur in accidents without the engagement of longitudinals, lateral loading to the occupant and/or very severe accidents with MAIS being much higher than the spine AIS.
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
While accident statistics on a national level are provided by many countries, there is a need for international data that includes more detailed information about the accident, so called in-depth data. As a consequence, accident data projects have been emerging in different regions of the world. This creates a need for comparable and mergeable data from different countries, enabling the use of already existing accident data resources and helping to expedite the improvement of global road safety. While existing approaches focus that mostly on building a comprehensive accident database from scratch, the iGLAD project (Initiative for the Global Harmonization of Accident Data) attempts a more pragmatic approach by building on top of the work already accomplished in this area and complementing it. The target of iGLAD is to help setting up an additional dataset as a compatibility layer between already existing world wide data sets and integrating the structure of these by defining a common data scheme. This dataset is limited to the common denominator between the existing data sets and is inherently rather small and simple. Eventually, an individual converter for each participating accident investigation group will be built that enables pooling all data sets in a common repository. This not only saves costs and time, and hence makes such a target more feasible, but also creates data that is usable right from the start. This paper gives an overview of the current status of iGLAD and first steps taken. Additionally, some methodological aspects are discussed, next to a glance at other projects working currently on related issues, providing additional input for iGLAD. Finally, an overview of next steps and intended future work is given.
Do learner gain sufficient braking capabilities at the end of education for collision avoidance?
(2013)
The paper describes a test design to evaluate the braking behaviour in the course of the driver education. The results show that the braking capabilities increased during the driver education and the learning effects are the same for males and females. The evaluation limit is set to 6 m/s-². At the beginning of education, 50% of the drivers do not reach this limit, although the driver education car is equipped with an emergency brake assist, which is regularly installed in all vehicles since 2009. After the education, 100% of the drivers can reach the limit. The results are mapped to a collision avoidance scenario.
Injuries in motorbike accidents in correlation with protective clothes and mechanism of the accident
(2013)
This study deals with a possible connection between safety clothing / accident mechanism and injury severity in a state-wide traffic accident investigation with focus on light and small motorbike-involvement for accidents in the area of the Saarland in which the persons riding the bike have been injured or killed. An interdisciplinary team of medical scientists and engineers collected the medical and technical data as well as all the relevant traces of the accident on scene and in time. During twenty months of data collection a total of 401 cases could be gathered. Grave injuries were more common for the group of heavier motorcycles (>125 ccm). Motorcyclists had been polytraumatized only in the group where the accident was connected with a collision. Significant correlation between protective clothes and injury severity could only be found for protective gloves and protective trousers. The knowledge about mechanism of the accident, protective clothes and severity of injuries can be helpful for the improvement of road and motorcyclists' safety.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
This study analyses no.39 cases in which n.41 motorcyclists were fatally injured, or 36% of total motorcycle fatalities in Northern Ireland between 2004 and 2010 (n.114). There were n.17 cases (43.6%) where the actions of another vehicle driver caused the collision, in thirteen of these cases the motorcycles had their lights switched on. The remaining n.22 collisions (56.4%) were due to the actions of the motorcyclist. In the approach to the collision scene, there were n.13 cases (31.7%) in which the approach was a right hand bend and in n.8 (19.5%) cases, the approach was a left hand bend. In the remaining n.18 (43.9%) cases, the approach was a straight road. Of the n.17 (41.4%) motorcycles that slid after falling, n.10 (24.4%) fell onto their right side and the remaining n.7 (17.1%) fell onto their left side. The information from this study identifies primary and contributory causes of motorcycle collisions.
The objective of the study is to measure the risk of pedestrian and bicyclist in urban traffic through an analysis of real-world accident data. The kinematics and injury mechanisms for both pedestrian and bicyclists are investigated to find the correlation of injury risks with injury related parameters. For this purpose, firstly 338 cases are selected as a sample from an IVAC accident database based on the In-depth Investigation of Vehicle Accident in Changsha of China. A statistic measurement of the fatality and serious injury risks with respect to impact speed was carried out by logistic regression analysis. Secondly, 12 pedestrian and 12 bicyclist accidents were further selected for reconstruction with MADYMO program. A comparative analysis was conducted based on the results from accident analysis and computer reconstructions for the injury risk, head impact conditions and dynamic response of pedestrians and bicyclists. The results indicate that bicyclists suffered lower risks of severe injuries and fatalities compared with pedestrians. The risks of AIS 3+ injury and fatality are 50% for pedestrians at impact speeds of 53.2 km/h and 63.3 km/h, respectively, while that for bicyclists at 62.5 km/h and 71.1 km/h, respectively. The findings could have a contribution to get a better understanding of pedestrians" and bicyclists" exposures in urban traffic in China, and provide background knowledge to generate strategies for pedestrian protection.
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
The effect of fatigue on driving has been compared to the effect of alcohol impairment in both driver performance and crash studies. However are crash characteristics and causation mechanisms similar in crashes involving fatigue to those involving alcohol when studied in the real world? This has been explored by examining data held in the EC project SafetyNet Accident Causation Database. Causation data was recorded using the SafetyNet Accident Causation System (SNACS). The focus was on Cars/MPV crashes and drivers assigned the SNACS code Alcohol or Fatigue. The Alcohol group included 44 drivers and the Fatigue group included 47. "Incorrect direction" was a frequently occurring critical event in both the Alcohol and Fatigue groups. The Alcohol group had more contributory factors related to decision making and the Fatigue group had more contributory factors relating to incorrect observations. This analysis does not allow for generalised statements about the significance of the similarities and differences between crashes involving alcohol and fatigue, however the observed differences do suggest that attempts to quantify the effect of fatigue by using levels of alcohol impairment as a benchmark should be done with care.
The European CASPER (Child Advanced Safety Project for European Roads) project studying car child safety includes a sociological approach in order to have a better understanding of the behaviour of parents driving children under 12 years old. A questionnaire was distributed via the internet in Europe with 998 parents (representing 1638 children) from 22 European countries responding. The results inform on the way parents secure their children during a car trip. Many parents did not control how their children were installed in the child restraint system (CRS). A toddler was more likely to travel into a child seat than an older child was. Regarding misuse situations, an important part of the participants did not think that they could make mistakes when fixing the child seat to the car (26%) or when placing the child into the seat (39%). This leaves an important field of action especially by communication via different media and in the CRS sale outlets.
Cycle helmets have continued to increase in popularity since their introduction half a century ago. Many studies indicate that overall, head injury can be significantly reduced by wearing them. This study was conducted using two distinct sets of real-world cycling collision data from Ireland, namely cases involving police collision reports and cases involving admission to a hospital emergency department. The analyses sought to simulate and analyse the protective performance of cycle helmets in such collision scenarios, by comparing the Head Injury Criterion score and peak head accelerations, both linear and angular. Cycle collisions were simulated using the specialised commercial software MADYMO. From the simulation results, these key metrics were compared between the same-scenario helmeted and unhelmeted cyclist models. Results showed that the inclusion of bicycle helmets reduced linear accelerations very significantly, but also increased angular accelerations significantly compared to unhelmeted situations. Given the modest protective performance of cycle helmets against angular accelerations, it is recommended that cycle helmet manufacturers and international test standards need to pay more attention to head angular accelerations.
The grip between the road surface and vehicle tires is the physical basis for the moving of all vehicles in road traffic. In case of an accident the available grip level is one of the most relevant influence factors, influencing the causation and the procedure of the accident. However, the estimation of the grip level is not easy and therefore, is commonly not done on the accident scene. This is especially true for the measurement of the water depth. Until now, real accident databases provide no measurement data about the grip level and the water film depth and thus, the estimation of its influence is not possible yet. From the tyre manufacturers point of view, it is important to know about the road conditions (namely grip level, macro-texture, water depth, temperature) at the accident scene, as well as the operating conditions of the vehicles (braking, loss of control, speed, etc). These data is necessary to define relevant tyre traction tests for the end-user and for regulations. For this reason VUFO and Michelin developed a consistent method for the measurements of grip level and water depth for the accidents of the GIDAS database. The accident research team of Dresden, which documents about 1000 accidents with at least one injured person every year, is measuring the micro-roughness and the macro-roughness directly on the spot. For the measurement of the micro-roughness a Skid Resistance Tester (British Pendulum) is used. The Mean Texture Depth (describing the macro-roughness) is measured by the Sand Depth Method. Since June 2009, measurements for more than 700 accidents including 1200 participants have been carried out. In case of wet or damp road conditions during the accident, the water depth is measured additionally. Therefore VUFO and Michelin developed a special measurement device, which allows measurements with an accuracy of 1/10 millimetre. The measurement point at the accident scene is clearly defined and thus, the results are comparable for all different accidents and participants. The use of the GIDAS database and the accident sampling plan allows representative statements for the German accident scenario. With this data it is possible for the first time to have an accurate view of the road conditions at the accident scene. One possibility is a more detailed estimation of hydroplaning accidents using the actually measured water depths. The development of new testing methods and new tires can be based on the real situation of the road infrastructure. Furthermore, the combination of the technical GIDAS data and the measured road surface properties can also be used for the estimation of effectiveness of several safety systems like the brake assist and/or emergency braking systems. The calculation of a reduced collision speed due to the use of a brake assist is only one example for the application of real measured grip level data.
The GIDAS-investigation team of Dresden (VUFO) has documented more than 11.500 accidents since 1999. The documentation of the accident includes beside vehicle-, injury- and environmental-data very detailed reconstruction data. Within this accident investigation the VUFO began to record the skid resistance of the accident site in 2009. The measurements are divided in macro- and microroughness (Sand depth method and Portable Skid Resistance Tester-SRT-by Munro-Stanley London-©). Both methods are used to determine the skid resistance for more than 1000 passenger cars. The aim of the present study is to find out a relationship between the measured skid resistance, the road conditions and the friction coefficient, which is used to calculate the maximum accelerations and decelerations during a reconstruction of an accident. Basic approach to convert the SRT-value into the friction coefficient is the calculation of the theoretical absorbed energy of the spring rubber system of the swinging arm of lever. This absorbed energy is used to get the friction coefficient by using the equations for the work of friction. To consider the road-behavior, in correlation to the friction coefficient, the results will be merged with existing literature. Last step for this study will be a comparison between actual used friction coefficients all over the GIDAS-database and the theoretical results. The study shows, if it is possible to use the SRT-Measurement for the estimation of a friction coefficient for the reconstruction of a traffic accident. As expected, the GIDAS-Database and the additional measurement of the roughness of the road directly on the spot are an enormous useful dataset.
Analysis of the accident scenario of powered two-wheelers on the basis of real-world accidents
(2013)
For the first time since 20 years the German national statistics of traffic accidents revealed an increasing number of fatalities and seriously injured persons in 2011. This negative development was especially caused by increasing numbers in all groups of vulnerable road users (VRU). Furthermore, the comparison of fatality reduction rates between several categories of road users shows that persons on motorcycles show the worst performance over years. Although every second fatality in German traffic accidents is still a car occupant, users of PTW make up more than 20% in the meantime. Assuming further improvements in the field of occupant protection this trend will continue. For that reason, a study on the basis of real-world accidents was conducted to describe the accident scenario involving motorcycles and to identify the reasons of the above-described fact. Approximately 1.800 motorcycle accidents out of GIDAS database were used for the analyses. The first part of the study deals with the question how representative the GIDAS database is for the German motorcycle accident scenario. Afterwards, detailed descriptive statistics on motorcycle accidents were presented considering numerous parameters about the accident scene, environmental influences, vehicle information, individual characteristics, interview data, injury severity and injury causation. One important point is the identification of the most frequent critical situations that are typical for motorcycle accidents. Furthermore, a special focus was on accident causation. Finally, conspicuous facts out of the analysis are emphasized. All in all, the study gives a comprehensive overview about the German motorcycle accident scenario. One the one hand, the use of weighted GIDAS data allows representative and robust statements on the basis of large case numbers; on the other hand highly detailed conclusions can be drawn. The results of the study help to understand the particularities of motorcycle accidents and provide approaches for further improvements in the field of PTW safety.
The sequence of accident events can be classified by three essential phases, the pre-crash-sequence, the crash-sequence and the post-crash-sequence. The level of reliability of the information in the GIDAS-database (German In Depth Accident Study) is provided predominantly on the passive side. The period to evaluate active safety systems begins already in the pre-crash-sequence. The assessment of the potential of sensor- or communication-based active safety systems can only be accomplished by a detailed analysis of the pre-crash-phase. Hence the necessity to analyze the early period of the accident event in detail arises. This is possible with the help of the digital sketches of the accident site and the simulation of the accident by a simulation method of the VUFO GmbH. After simulating the pre-crash scenario it is possible to generate additional and standardized data to describe the pre-crash-sequences of an accident in a very high detail. These data are documented in a second database called the GIDAS Pre-Crash-Matrix (PCM). The PCM contains various tables with all relevant data to reproduce the pre-crash-sequence of traffic accidents from the GIDAS database until 5 seconds before the first collision. This includes parameters to describe the environment data, participant data and motion or dynamic data. This paper explains the creation of the PCM, the simulation itself and the contents and structure of the PCM. With this information of the pre-crash-sequence for various accident scenarios an improved benefit estimation and development of active safety systems can be made possible.
The increasing economics in India has an enormous growth of its road traffic. As observed from official Indian accident statistics the number of road fatalities are one of the highest worldwide. In contrast to most industrialized nations they have an rapidly increasing trend. To come along with this trend it becomes more than essential to understand the traffic accident situation. The official Indian accident statistics gives a glimpse of only basic information. Therefore more detailed data is needed. By using In-depth accident data and officially representative statistics the current accident situation can be evaluated in India, if a suitable weighting methodology is considered. Hence in 2009/2010 a pilot study with the collaboration partner JP-Research India pvt. Ldt. was gathered in Tamil Nadu in south of India. In-depth accident investigations were done around the Coimbatore area on four highways. At first, the collected data is evaluated. Due to consequent and continuous further development based on the first approach a methodology similar to NASS/CDS/GES in the US and GIDAS in Germany was developed. Of course all relevant accident related parameters including pictures and severity information were collected. As a matter of fact based on scaled sketches and reconstruction benefit analyses can be done in order to analyze the accident scenery in India. As a first outcome influence from infrastructure, missing education and vehicle safety were identified as key parameters in order to reduce the number of accidents and casualties. To compare the accident situation against international standards an accident classification for left hand traffic was developed based on the German Insurance classification system. Looking into detail additional accident types were identified and added to create an Indian accident type catalogue. The positive results encouraged several OEMs to participate in this investigation and together with BOSCH a consortium was established in 2010/11. Within one year from beginning in May 2011 about 200 highway accidents were collected, reported and reconstructed using the new standard. Hence a first good overview of the accident situation is available for the Coimbatore Tamil Nadu area. The major target for establishing accident investigations is the extension towards other states of India and urban areas to achieve a better overview of the accident scenery. Therefore local and national authorities have to be embedded in order to strengthen the awareness against traffic safety.
Im von der DG Home (CIPS Program) geförderten Projekt "SecMan " Security Manual for Road Infrastructures" wurde ein vierstufiges Verfahren zur Identifikation kritischer Straßeninfrastrukturen, ihre Bewertung hinsichtlich diverser von Menschen verursachter Gefahren sowie die Bestimmung effektiver Schutzmaßnahmen entwickelt. Diese Ergebnisse wurden in einem ganzheitlichen "best-practice" Handbuch zusammen getragen, welches einen trans-nationalen Sicherheitsmanagement-Ansatz für Betreiber und Eigentümer von Straßeninfrastrukturen in Europa ermöglicht. Im Folgenden wird die entwickelte Methodik vorgestellt, ausgehend von der Bewertung der Netzkritikalität über die Attraktivität und Vulnerabilität eines Bauwerks hin zu einer Bewertungsmethodik für die Auswahl geeigneter Schutzmaßnahmen.
With an ever rising human life expectancy the share of elderly people in society is constantly rising. This leads to the fact that at the same rate the share of people with age related diseases such as dementia and poor eyesight taking part in traffic will rise and therefore traffic accidents caused by this group of people due to the disease will play an ever greater role. This Situation will be among the future challenges of road safety work. At present this study displays specific characteristics of accidents caused by elderly car drivers (aged 65 or higher) based on the analysis of the German In-Depth Accident Study GIDAS. Herein almost 1000 elderly car drivers were identified as accident participants in the years 2008 to 2011. The focus of this study lies on identifying special types of accidents which are caused by elderly drivers and on characterizing these types with the information gathered on scene and by interviewing the participants. The main evidence analyzed is the knowledge about the accident locality, the trajectories of the participants as well as the reasons for the occurrence of the accidents. Furthermore personal information such as the personal condition before the accident and driving purposes is used to identify patterns of contributing circumstances for accidents caused by elderly traffic participants.
Having a look at safety to traffic and the prevention of accidents it can be observed that technical improvements in active safety of vehicles have let to various positive effects in this area. Among other components the tyre-road-contact takes a key role in the development of active safety technologies. All forces in accelerating, breaking and vehicle guidance have to be transmitted through the tyre-road contact area by friction forces. A common way to characterize a friction process is to identify the coefficient of friction μ between two touching materials. Even though there are several approaches to experimentially characterise road surfaces, no standard method exists. In this paper an overview of existing test methods is given. Furthermore the preliminary design of a newly developed portable test device with its possibility to investigate the tyre-road-friction of arbitrary roads or even places of accidents is shown.
Since 2008, the authors inspected fatal traffic accidents on the spot every year, with the cooperation of Toyota police station in Aichi pref. In the jurisdiction, numbers of fatal accidents were 18 in 2008, 12 in 2009, 14 accidents in 2010, and 16 in 2011. We here report the results of our analysis of information obtained by detailed inspection for those that occurred from 2008 to 2010. We focused on vehicle-to-pedestrian accidents, which accounted for about 45% of all accidents in 2008. Because many accidents occurred on residential roads not far from pedestrians" homes, it was revealed that the decrease of the collision speed by traffic calming such as humps and zone speed management, was highly effective. On the other hand, pedestrian detection technologies seemed to be also effective as a countermeasure on vehicle side. Every pedestrian position against a vehicle was clarified and TTC (Time to Collision) was calculated provisionally. Pedestrian accidents in intersections were also examined. Among the intersection pedestrian accidents within the jurisdiction, compared with the national average in Japan, the ratio of intersections without a signal and the ratio without a pedestrian crossing were high. According to the comparison of the Japanese traffic accident patterns between 2001 and 2008, pedestrian accidents during turning right and turning left did not decrease much. For elderly drivers, these accidents occurred very often. Finally, single vehicle accidents were analysed with the accident pattern analysis methods used above. There were high numbers of single vehicle accidents against object on single roads. Although fatal accidents against guardrails decreased, the numbers of fatal accidents against a utility pole and a sign pole were nearly constant. As for the impact with narrow width objects such as utility poles, the fatality rate was very high, and countermeasures of both road infrastructure and vehicles seem to be effective.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.