Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (404) (entfernen)
Schlagworte
- Conference (324)
- Konferenz (320)
- Germany (151)
- Accident (150)
- Unfall (150)
- Deutschland (149)
- Injury (101)
- Verletzung (100)
- Unfallrekonstruktion (81)
- Analyse (math) (64)
Small overlap frontal crashes are defined by a damage pattern with most of the vehicle deformation concentrated outboard of the main longitudinal structures. These crashes are prominent among frontal crashes resulting in serious and fatal injuries, even among vehicles that perform well in regulatory and consumer information crash tests. One of the critical aspects of understanding these crashes is knowing the crash speeds that cause the types of damage associated with serious injuries. Laboratory crash tests were conducted using 12 vehicles in three small overlap test conditions: pole, vehicle-to-vehicle collinear, and vehicle-to-vehicle oblique (15-degree striking angle). Field reconstruction techniques were used to estimate the delta V for each vehicle, and these results were compared with actual delta V values based on vehicle accelerometer data. Estimated delta Vs were 50% lower than actual values. Velocity change estimates for small overlap frontal crashes in databases such as NASS-CDS significantly underestimate actual values.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
Causation patterns and data collection blind spots for fatal intersection accidents in Norway
(2010)
Norwegian fatal intersection accidents from the years 2005-2007 were analysed to identify any causation patterns among their underlying contributing factors, and also to evaluate whether the data collection and documentation procedures used by the Norwegian in-depth investigation teams produces the information necessary to perform causation pattern analysis. A total of 28 fatal accidents were analysed. Details on crash contributing factors for each driver in each crash were first coded using the Driving Reliability and Error Analysis Method (DREAM), and then aggregated based on whether the driver was going straight or turning. Analysis results indicate that turning drivers to a large extent are faced with perception difficulties and unexpected behaviour from the primary conflict vehicle, while at the same time trying to negotiate a demanding traffic situation. Drivers going straight on the other hand have less perception difficulties. Instead, their main problem is that they largely expect turning drivers to yield. When this assumption is violated, they are either slow to react or do not react at all. Contributing factors often pointed to in literature, e.g. high speed, drugs and/or alcohol and inadequate driver training, played a role in 12 of 28 accidents. While this confirms their prevalence, it also indicates that most drivers end up in these situations due to combinations of less auspicious contributing factors. In terms of data collection and documentation, information on blunt end factors (those more distant in time/space, yet important for the development of events) was more limited than information on sharp end factors (those close in time/space to the crash). A possible explanation is that analysts may view some blunt end factors as event circumstances rather than contributing factors in themselves, and therefore do not report them. There was also an asymmetry in terms of reported obstructions to view due to signposts and vegetation. While frequently reported as contributing for turning drivers, they were rarely reported as contributing for their counterparts in the same accidents. This probably reflects an involuntary focus of the analyst on identifying contributing factors for the driver legally held liable, while less attention is paid to the driver judged not at fault. Since who to blame often is irrelevant from a countermeasure development point of view, this underlying investigator mindset needs addressing to avoid future bias in crash investigation reports.
Providing effective occupant protection in rollover crashes requires supplying the occupant with a restraint system proven effective in the dynamic rollover accident mode. Preventing ejection and providing restraint sufficient to prevent potentially injurious contacts with both interior and exterior vehicle components is paramount for effective rollover occupant protection. Research has shown that the injury potential can be decreased by closely coupling the occupant to the seat. This paper focuses on the effect of restraint system slack and its relationship to occupant excursion and ejection potential during rollover. Various restraint system configurations are evaluated in rollover-type test environments. A review of prior research is presented prior to presenting new quasi-static vehicle inversion studies conducted with live surrogate occupants. Additionally, dynamic rollover testing utilizing anthropometric test devices (ATDs) is presented. The influence of belt looseness and effects of various restraint designs on the belted occupants' injury potential are discussed.
In road traffic accidents, a car-seat and its occupant can be subjected to various crash pulses in the case of a rear impact. This study investigates the influence of crash pulse shape on seat-occupant response and evaluates the corresponding risk of whiplash injury. For this purpose, a rigorously validated seat-occupant system model is used to study different carseat designs and crash pulses. Two different car-seat concepts are also presented which can effectively mitigate whiplash injury for a wide range of crash severity. It is shown that for crash pulses of similar severity, the level of whiplash-risk depends strongly on the combined effects of seat design and crash pulse shape.
Although the statistics show a decreasing rate of child injuries and fatalities in German road accidents more efforts can be made to protect children in cars e.g. by developing appropriate child restraint systems. An important part in of this work can be achieved with the help of crash tests using child dummies. However these crash tests cannot completely reflect the situation of real world crashes as factors like children moving out of the optimal position or children incorrectly fastened by their parents are difficult to predict. Therefore this study gives an overview over the current accident and injury situation of child occupants in cars in German road accidents.
Recent findings from real-world accident data have shown that fatality risks for pedestrians are substantially lower than generally reported in the traffic safety literature. One of the keys to this insight has been the large and random sample of car-to-pedestrian crashes available in the German In-Depth Accident Study (GIDAS). Another key factor has been the proper use of weight factors in order to adjust for outcome-based sampling bias in the accident data. However, a third factor, a priori of unknown importance, has not yet been properly analysed. This is the influence of errors in impact speed estimation. In this study, we derived a statistical model of the impact speed errors for pedestrian accidents present in the GIDAS database. The error model was then applied to investigate the effect of the estimation error on the pedestrian fatality risk as a function of car impact speed. To this end, we applied a method known as the SIMulation-EXtrapolation (SIMEX) method. It was found that the risk curve is fairly tolerant to some amount of random measurement error, but that it does become flattened. It is therefore important that the accident investigations and reconstructions are of high quality to assure that systematic errors are minimised and that the random errors are under control.
The NHTSA-sponsored Crash Injury Research and Engineering Network (CIREN) has collected and analyzed crash, vehicle damage, and detailed injury data from over 4000 case occupants who were patients admitted to Level-I trauma centers following involvement in motor vehicle crashes. Since 2005, CIREN has used a methodology known as "BioTab" to analyze and document the causes of injuries resulting from passenger vehicle crashes. BioTab was developed to provide a complete evidenced-based method to describe and document injury causation from in-depth crash investigations with confidence levels assigned to the causes of injury based on the available evidence. This paper describes how the BioTab method is being used in CIREN to leverage the data collected from in-depth crash investigations, and particularly the detailed injury data available in CIREN, to develop evidence-based assessments of injury causation. CIREN case examples are provided to demonstrate the ability of the BioTab method to improve real-world crash/injury data assessment.
Bone fracture patterns could be crucial in reconstructing the nature of loading, especially in the lower limb and upper limb kinematics in vehicle-pedestrian crashes. In addition, use of FE bone models can be a handy tool to predict vehicle impact velocity and the impact direction. The point of fracture initiation in bone loading has been predicted quite accurately earlier. A methodology that predicts bone crack initiation and its propagation pattern for the six known loading directions using a single material and failure model is presented.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
Brücken in ungünstiger geographischer/geomorphologischer Lage " z.B. über Gewässer, in Einschnitten, Schattenlagen und Niederungsbereichen " neigen konstruktionsbedingt gegenüber den angrenzenden bodengebundenen Fahrbahnen zur vorzeitigen Glättebildung, die eine besondere Gefährdung der Verkehrsteilnehmer - vor allem im Spätherbst und im zeitigen Frühjahr - darstellt. Die Erneuerung der Straßenbrücke B 208 / Elbe-Lübeck-Kanal in der Ortslage Berkenthin im Kreis Herzogtum Lauenburg bot auf Grund ihrer besonderen kleinklimatischen Situation die Möglichkeit, im Rahmen eines Pilotprojektes - aufbauend auf den Ergebnissen des Forschungsprojektes 15.401 "Vermeidung von Glatteisbildung auf Brücken" der BASt " die Fahrbahntafel mittels oberflächennaher geothermischer Energie zu temperieren. Die bei Planung, Bau sowie in der nunmehr anlaufenden Nutzungsphase gewonnenen Erkenntnisse sollen den Straßenbaulastträgern Hinweise und Entscheidungshilfen geben, die Verkehrssicherheit wie auch die Nachhaltigkeit bei glättegefährdeten Brücken und Straßenabschnitten durch den Einsatz alternativer Energien zu erhöhen und gleichzeitig den Aufwand für den präventiven Winterdienst zu reduzieren. Der hierfür erforderliche Kapitaleinsatz ist eher in volkswirtschaftlicher Hinsicht und erst in zweiter Linie betriebswirtschaftlich zu bewerten.
Im Rahmen eines von der Bundesanstalt für Straßenwesen (BASt) initiierten Forschungsvorhabens (15.449/2007/ERB: "Prüfverfahren zur Beurteilung der Lebensdauer von Kunststoffdichtungsbahnen für Straßentunnel") wurden anhand von Untersuchungen an Kunststoffdichtungsbahnen (KDB) auf Basis von Polyolefinwerkstoffen die Möglichkeiten der Beurteilung der oxidativen Langzeitbeständigkeit sondiert. Im Mittelpunkt stand die Erprobung des Autoklaventests in Anlehnung an DIN EN ISO 13438 (Methode C1/C2) an ausgewählten, für den Tunnelbau repräsentativen marktüblichen KDB-Produkten. Die Untersuchungen im Autoklaven bei erhöhten Temperaturen (60 -°C, 70 -°C und 80 -°C) und Sauerstoffdrücken (11, 21 und 51 bar) wurden durch vergleichende Versuche im Wärmeschrank (Ofen) bei erhöhter Temperatur (85 -°C) in Anlehnung an DIN EN 14575 ergänzt. Die KDB-Produkte wurden außerdem einer eingehenden Materialcharakterisierung (Zugprüfung, OMA, DSC) unterzogen. Weiterhin wurden Bauwerksdaten recherchiert und auf ihre Nutzbarkeit zur Bewertung und Prüfbarkeit der Langzeitbeständigkeit von KDB in Tunneln betrachtet. Ziel war auch, die Anwendbarkeit des bisher vorgeschlagenen Extrapolationsmodells zur Auswertung der Ergebnisse von Autoklaventests an im Tunnelbau marktüblichen Produkten für Nutzungsdauern über 25 Jahre zu überprüfen und zur Entwicklung eines geeigneten Prüfverfahrens beizutragen. Der Beitrag geht auf Ergebnisse des Vorhabens ein und zeigt erste Schlussfolgerungen und weiteren Untersuchungsbedarf auf. Die Ergebnisse werden in den "Empfehlungen zu Dichtungssystemen im Tunnelbau EAG-EDT" des Arbeitskreises 5.1 "Kunststoffe in der Geotechnik und im Wasserbau" berücksichtigt, deren 2. Auflage in Vorbereitung ist. Aspekte des thermischen Verhaltens der eingesetzten Werkstoffe sowie mögliche Anpassungen der Prüfrandbedingungen für die Autoklaventests werden ergänzt und Hinweise zur Interpretation von Prüfergebnissen gegeben. Außerdem wurden inzwischen ausgehend von den Ergebnissen des Forschungsvorhabens erste Autoklaven-Ringversuche in drei Prüfinstitutionen initiiert.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Kategorie-1-Schäden bei orthotropen Fahrbahnplatten treten als bauweisenunabhängige Schäden in Form von Rissen im Anschlussbereich Deckblech-Längsrippe auf. Zur Vermeidung dieser Schäden sind geeignete Instandsetzungsmaßnahmen zu entwickeln, die zu einer Verminderung der Spannungen und Durchbiegungen in den gefährdeten Bereichen führen. Im Rahmen eines aktuellen Forschungsvorhabens an der Universität Duisburg-Essen wird der Ansatz verfolgt, einen modifizierten Fahrbahnbelag bestehend aus einem mit Epoxydharz oder alternativ mit Bioharz verfüllten Asphalttraggerüsts mit erhöhter mittragender Wirkung einzusetzen. Des Weiteren wird im vorliegenden Beitrag der Einsatz von Betonfertigteilen aus UHPC erläutert.
Im Jahr 2005 wurde mit dem Bau der Niederrheinbrücke Wesel der Bau der Ortsumgehung Wesel begonnen. Der Beitrag berichtet über einige Ausführungsdetails der im Jahr 2009 fertiggestellten Baumaßnahme: die Herstellung des Pylons in hochfestem Beton, die Montage der Strombrücke, der Einsatz von Parallellitzenbündeln.
W.-D. FRIEDRICH schildert in seinem Einführungsvortrag die praktischen Erfahrungen und Probleme der DEGES Deutsche Einheit, Fernstraßenplanungs- und -bau GmbH beim straßenrechtlichen Grunderwerb. Die DEGES ist dazu übergegangen, den Grunderwerb unter Einbeziehung von Dienstleistungsfirmen zu realisieren, was sich als effizient, kostengünstig und flexibel erwiesen hat. Im Zuge der Vorbereitung und Durchführung von Besitzeinweisungsverfahren bilden namentlich der Nachweis der Dringlichkeit und die Besitzeinweisung für Ausgleichs- und Ersatzmaßnahmen Problemschwerpunkte. Im Zentrum der Rechtsstreitigkeiten der eigentlichen Enteignungsverfahren steht die Verkehrswertermittlung, wobei FRIEDRICH beispielhaft die Bewertung von Grundstücken, in denen bergfreie Bodenschätze lagern, und die kontrovers umstrittene Frage der Berücksichtigung von Betriebsprämien als gesicherte Rechtsposition diskutiert. E. ALLESCH berichtet über aktuelle Rechtsfragen der straßenrechtlichen Enteignung, die sich aus Sicht der Verwaltungsgerichtsbarkeit stellen. Er verdeutlicht das Zusammenspiel der Vorschriften des Bundesfernstraßengesetzes (-§ 18f, -§ 19 FStrG) mit dem Enteignungsrecht der Länder und behandelt als Einzelprobleme unter anderem die Probleme der Enteignung und Besitzeinweisung auf Grundlage eines isolierten Straßenbebauungsplans, die Fragen der Wirksamkeit und Durchsetzbarkeit einer Einigung in und ausserhalb des Enteignungsverfahrens, das Erfordernis des sofortigen Baubeginns im Sinne des -§ 18f Abs. 1 Satz 1 FStrG und die Frage nach dem Ausschluss "weiterer Voraussetzungen" nach -§ 18f Abs. 1 Satz 3 FStrG. H. SCHMITZ liefert einen Bericht zum Stand der geplanten Vereinheitlichung der Fachplanungsgesetze im Verwaltungsverfahrensgesetz, die insbesondere auf eine Verallgemeinerung der Regelungen des Infrastrukturplanungsbeschleunigungsgesetzes abzielt. Er stellt dabei namentlich den Inhalt des Musterentwurfs der Verwaltungsverfahrensrechtsreferenten von Bund und Ländern mit den letzten Fortschreibungen vor. T. TEGTBAUER beschreibt in ihrem Beitrag zur "Privatisierung im Straßenbau" die aktuellen Erfahrungen des Bundes mit dem sog. A-Modell. Einer Darstellung des Konzepts selbst folgen eine Chronologie der Entwicklung der A-Modelle, eine Vorstellung der vier A-Modell-Pilotprojekte sowie des strukturierten Verhandlungsverfahrens und insbesondere der Wirtschaftlichkeitsuntersuchung i. S. v. -§ 7 BHO. Die Auswertung der vier Pilotprojekte ergab, dass die selbst gesteckten Ziele mit den Pilotprojekten teilweise erreicht wurden, weshalb der Bund mit den Ländern bereits acht weitere Projekte abstimmen konnte. G. RECKER vervollständigt dieses Bild aus Sicht eines Landes und berichtet über die Grundsanierung und den erforderlichen Ausbau auf sechs Streifen eines Streckenabschnitts der BAB 1, die die stark befahrenen Strecken von Schleswig-Holstein bis Saarbrücken und die Seehäfen Norddeutschlands mit dem Westen Deutschlands verbindet und Teil der transeuropäischen Netze ist. Im Ergebnis ist der Aufwand für das gebündelte Vergabeverfahren im Vergleich zur Durchführung von sieben Einzelverfahren geringer ausgefallen, wobei weitere Synergieeffekte als möglich angesehen werden. Allerdings ist gerade in der Umsetzungsphase auch auf Seiten des Konzessionsnehmers noch die erforderliche Routine auszubauen.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
Herber diskutiert angesichts des Auseinanderklaffens einerseits der aktuellen Verkehrsprognosen " die namentlich auf den Autobahnen von 2004 bis 2025 Verkehrszuwächse von 44 % veranschlagen " und andererseits der finanziellen und ökologischen Begrenzungen der künftigen Verkehrspolitik verschiedene Vorschläge zur Reform der Bundesauftragsverwaltung, der Netzplanung, der Netzbereinigung und der Netzbildung sowie zur besseren Einbindung der Bürger in die Planungsverfahren von Straßeninfrastrukturprojekten. Geigers Beitrag zum planfeststellenden Bebauungsplan gelangt zu einem skeptischen Befund: Nach seiner Einschätzung sprechen insgesamt überwiegende Gründe dafür, Straßenbauvorhaben regelmäßig durch Planfeststellung und nicht durch planfeststellungsersetzenden Bebauungsplan festzusetzen. Insbesondere von dem Instrument des isolierten Straßenbebauungsplans solle nur in Ausnahmefällen Gebrauch gemacht werden. Selbst im Gesamtkontext einer umfassenden städtebaulichen Umgestaltung empfehle sich meist eine zeitlich und inhaltlich aufeinander abgestimmte Planung, bei der sich die Gemeinde auf die städtebaulichen Planungen beschränke und die straßenseitige Planung der Straßenbauverwaltung überlasse. Der Beitrag zu "notwendigen Folgemaßnahmen" von Gaentzsch diagnostiziert trotz einer ganzen Reihe einschlägiger Präjudizen weiterhin erhebliche Rechtsunsicherheiten bei der Anwendung des -§ 75 Absatz 1 Satz 1 und des -§ 78 VwVfG. Skeptisch äußert sich Gaentzsch gegenüber dem Versuch, die Voraussetzungen beider Regelungen weiter gesetzlich zu konkretisieren. Er empfiehlt stattdessen, in Zweifels- oder Streitfällen die gemeinsame oberste Behörde entscheiden zu lassen und zudem die Fehlerfolgenregelung des -§ 75 Absatz 1a VwVfG auch auf Fehler im Bereich der Folgemaßnahmen auszuweiten. Der abschließende Beitrag von Sauthoff zur "Abstufung nicht mehr fernverkehrsrelevanter Bundesfernstraßen" widmet sich einem zentralen verfassungsrechtlichen Streitpunkt des Straßenrechts der letzten Jahrzehnte. Er diskutiert neuere gutachtliche Ausarbeitungen zur Überprüfung des Bundesfernstraßennetzes, die er als Verhandlungsgrundlage zwischen Bund und Ländern ansieht. Die in den Richtlinien für integrierte Netzgestaltung (RIN) vorgesehene Anknüpfung an das raumordnerische Zentrale"Orte"System bei der Klassifizierung des Straßennetzes sei jedoch nur mit Modifikationen möglich; rechtlich entscheidend seien allein die verfassungsrechtlich fundierten Kriterien des -§ 1 Absatz 1 FStrG und damit letztlich die " gegebenenfalls geänderte " Verkehrsbedeutung der Straße. Bei Anwendung dieser Maßstäbe sei grundsätzlich auch eine Weisung des Bundes auf Einziehung zulässig. Einen Bedarf für eine Novellierung des Bundesfernstraßengesetzes verneint der Referent.