Sonstige
Filtern
Dokumenttyp
Sprache
- Englisch (43) (entfernen)
Schlagworte
- Verletzung) (43) (entfernen)
Institut
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
To date, the Trauma Registry (TraumaRegister DGU-® contains data of approximately 100.000 severely injured patients, 65% of which suffered from a road traffic crash. Thus, it is the world's largest data base for severely injured patients. The article describes the development of the registry and explains how it was rolled out over Germany using the established structure of the German Trauma Network (TraumaNetzwerk DGU-®). In addition, this article presents three typical use cases from the fields of quality management, policy making and system-wide interventions, clinical research and injury prevention. In conclusion, the TraumaRegister DGU-® is a well-established tool for various purposes related to the control and reduction of the burden of road injury. Its ongoing expansion to other countries will support the goal of international benchmarking of hospitals and trauma systems.
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
The significant demographic changes are predicted for the European future. The age group over 65 years is permanently increasing and over next 30 years every fourth person will belong to this group. This development will continue so far that by 2050 in many countries will double the percentage of the population aged 65 and more. Many studies analyze the new phenomena of the ageing (graying) society during the last decade. Mobility is integrated part of the life of every citizen, even more it means for the elderly people. The adequate mobility is the precondition for their active life and for their social communication that contribute to their health and functional capacity and their autonomy and independency. The active seniors demand less public support. The mobility of the older citizens is closely linked with health and societal problems and creates an important public challenge. On the other side the participation of seniors in transport due to their limited physical and mental possibilities means for them an increased risk to be injured or killed. The main mobility spaces are roads that can be used not only as a traveler in a vehicle (driver or passenger) but also as a pedestrian or cyclist or even as a motorcyclist. The road traffic is then an opportunity and danger in the same time. The accident analyzes show specific risk features of seniors that are different compared with other age groups. First of all the older road users (65 and more) are facing to the higher risk (number of killed divided by the population size) to be killed in a road accident compared with the group of younger road users (0 - 64). More significant difference can be observed when comparing the road user groups. The fatality percentage of the older pedestrians is 2,5 times higher compared with the group 25 " 64. Similar frequency show the cyclist fatalities. On the other side the vehicle passengers in the younger group have more or less two time higher percentage compared to seniors and in the group of motorcyclists even achieved in 2008 almost five times higher compared with the older group. The share of the old road users fatalities (around 19%) didn"t practically change during the last 10 years in the European average. But comparing the gender involvement (2006) there is an interesting difference " female fatalities make 30, 2%, male fatalities 15, 3% of all fatalities in their groups. The risk of the senior users is more connected with their physical and mental limits than with their risk behavior. According to the Czech statistics (2007) the vehicle drivers over 65 years cause only 3, 6% of all accidents. The solution of the problem is to minimize the risk and to create a safe environment for the elderly people using the roads. In order to achieve this goal a deep knowledge of risk and of accident circumstances, full understanding of the behavior of the seniors and their limitations and accommodating approach of the whole society is necessary. Road risk of the ageing society has to be considered as a part of the health and social policy. These can build a creditable basis for the implementation of the measures that secure safe moving of seniors on the roads.
The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx. However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My. The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was observed. It was also observed that the primary neck response in these tests was flexion, not extension. This correlates well with recent findings from Japan and the United States showing a correlation between neck flexion and injury in accident replication simulations and postmortem human subjects (PMHS) studies, respectively. The present certification tests may not adequately control front cervical spine bumper characteristics, which are important for neck flexion response. The certification sled test also does not include the pelvis and so cannot be used to control pelvis response and does not substantially load the lumbar bumpers and so does not control these parts of the dummy. The stiffness of all spine bumpers and of the pelvis flesh should be much more tightly controlled. It is recommended that a method for certifying the front cervical bumpers should be developed. Recommendations are also made for tighter tolerance on the input parameters for the existing certification tests.
Police records about traffic accidents like used by IRTAD (International Road Traffic and Accident Database) and CARE (Community Road Accident Database) do not represent all road injuries. For instance, road accidents of bicyclists without a counterpart are usually not reported. Furthermore, IRTAD-like data contains hardly any information on injury outcome and accident circumstances. This information gap leads to an under-representation of the safety concerns of the most vulnerable road users like children and the elderly both in accident research and safety promotion. Injury registration for the European Injury Database (IDB), in turn, combines details of accident causation with diagnostic information that can be used to assess injury severity and long term consequences. The IDB is collecting data from hospital emergency department patients and is being implemented in a growing number of countries. In this article IDB results on mode of transport and injury outcome are presented from a sample of nine EU member states.
Impact severity is a fundamental measure for all in-depth crash investigation projects. One methodology used in the UK is based on the US Calspan software package CRASH3. The UK- in-depth crash investigation studies routinely use AiDamage3 a software package which is based on an updated version of the original CRASH3 algorithm, including enhancements to the vehicle stiffness coefficients. Real world accident-damaged vehicles are measured and their crush is correlated with a library of stiffness coefficients. These measurements are then used, along with other parameters, to calculate the crash energy and equivalent changes of velocity of the vehicles (delta-v), which is a measure of the impact severity. UK in-depth accident studies routinely validate the crash severity methodologies applied as the vehicle fleet changes. This is achieved by analysing crash test data and using the appropriate residual crush damage and other inputs to AiDamage3 and checking the program- outputs with the known crash severity parameters. This procedure checks, at least in part, the default stiffness values in the data libraries and the reconstruction methods used.
The bicyclist accidents were analyzed to get better understanding of the occurrences and frequency of the accidents, injury distributions, as well as correlation of injury severity/outcomes with engineering and human factors in two different countries of China and Germany. The accident cases that occurred from 2001 to 2006 were collected from IVAC database in Changsha and GIDAS database in Hannover. Based on specified sampling criteria, 1,570 bicyclist cases were selected from IVAC database in Changsha, and 1806 cases were collected from Hannover, documented in GIDAS database. Statistical analyses were carried out by using these selected data. The results from the statistical analysis are presented and discussed in this study.
Introduction: Spine injuries pose a considerable risk to life and quality of life. The total number of road deaths in developed countries has markedly decreased, e.g. in Germany from over 20000 in 1970 to less than 4000 in 2010, but little is known how this is reflected in the burden of spine fractures of motor vehicle users. In this study, we aimed to show the actual incidence of spine injuries among drivers and front passengers and elucidate possible dependencies between crash mechanisms and types of injuries.
This study aims to analyze spine injuries in motor vehicle accidents. Between 1985 and 2004 the Hannover accident research unit documented 18353 accidents. We identified 161 front passengers (0.53%) with cervical spine injuries, 84 (0.28%) with thoracic and 95 (0.31%) with lumbar injuries. Technical and medical data was reviewed. Patients" records were retrieved. X-rays were evaluated and fractures were classified according to the Magerl classification. 68% and 57% of thoracic and lumbar fractures occurred in accidents with multiple impacts. Delta-v was 50, 40 and 40 kph in passengers with cervical, thoracic and lumbar spine, resp. Passengers with spinal fractures frequently showed numerous concomitant injuries, e.g. additional vertebral fractures. The influence of seat belts and airbags is discussed. Patient work-up has to include a thorough investigation for additional injuries.
In Germany averagely two million traffic accidents happen each year and emergency medical services are called to more than 400 000 patients. Even though this number is decreasing continuously (due to improvements in the fields of vehicle safety, road construction, and accident prevention) every case is yet a challenge for the rescuers and requires improvements in emergency medicine as well. Especially during diagnostics right at the accident scene, there are only limited instruments available to gain the necessary knowledge of the injuries suffered, to come to essential decisions about treatment or transport. To provide an additional diagnostic aid by scouting and estimating the situation, a software-tool calculating the likeliness of the most frequent severe injuries (AIS 3-6) of front occupants in passenger cars has been developed to deliver this necessary information about particular accident scenarios. To achieve this, logistic likelihood functions have been calculated in a multivariate regression analysis analysing all AIS 3+ injuries in the GIDAS database of the years 1999-2006 that happened more than four times
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Test and assessment procedures for passive pedestrian protection based on developments by the European Enhanced Vehicle-safety Committee (EEVC) have been introduced in world-wide regulations and consumer test programmes, with considerable harmonization between these programmes. Nevertheless, latest accident investigations reveal a stagnation of pedestrian fatality numbers on European roads running the risk of not meeting the European Union- goal of halving the number of road fatalities by the year 2020. The branch of external road user safety within the EC-funded research project SENIORS under the HORIZON 2020 framework programme focuses on investigating the benefit of modifications to pedestrian test and assessment procedures and their impactors for vulnerable road users with focus on the elderly. Injury patterns of pedestrians and cyclists derived from the German In-Depth Accident Study (GIDAS) show a trend of AIS 2+ and AIS 3+ injuries getting more relevant for the thorax region in crashes with newer cars (Wisch et al., 2017), while maintaining the relevance for head and lower extremities. Several crash databases from Europe such as GIDAS and the Swedish Traffic Accident Data Acquisition (STRADA) also show that head, thorax and lower extremities are the key affected body regions not only for the average population but in particular for the elderly. Therefore, the SENIORS project is focusing on an improvement of currently available impactors and procedures in terms of biofidelity and injury assessment ability towards a better protection of the affected body regions, incorporating previous results from FP 6 project APROSYS and subsequent studies carried out by BASt. The paper describes the overall methodology to develop revised FE impactor models. Matched human body model and impactor simulations against generic test rigs provide transfer functions that will be used for the derivation of impactor criteria from human injury risk functions for the affected body regions. In a later step, the refined impactors will be validated by simulations against actual vehicle front-ends. Prototyping and adaptation of test and assessment procedures as well as an impact assessment will conclude the work of the project at the final stage. The work will contribute to an improved protection of vulnerable road users focusing on the elderly. The use of advanced human body models to develop applicable assessment criteria for the revised impactors is intended to cope with the paucity of actual biomechanical data focusing on elderly pedestrians. In order to achieve optimized results in the future, the improved test methods need to be implemented within an integrated approach, combining active with passive safety measures. In order to address the developments in road accidents and injury patterns of vulnerable road users, established test and assessment procedures need to be continuously verified and, where needed, to be revised. The demographic change as well as changes in the vehicle fleet, leading to a variation of accident scenarios, injury frequencies and injury patterns of vulnerable road users are addressed by the work provided by the SENIORS project, introducing updated impactors for pedestrian test and assessment procedures.
Real world accident reconstruction with the Total Human Model for Safety (THUMS) in Pam-Crash
(2013)
Further improvement of vehicle safety needs detailed analysis of real world accidents. According to GIDAS (German In-Depth Accident Study) most car to car front accidents occur at mid-crash severity. In this range thoracic injuries already occur. In this study a real world frontal crash with mid-crash severity out of the AARU database was reconstructed. The selected car to car accident was reconstructed by AARU by means of pc-crash software in order to get the initial dynamic accident conditions. These initial conditions were used to reconstruct the complete accident in more detail using FE models for the car structure and the occupants. Occupant simulations were performed with FE HIII-dummy models and the THUMS using Pam-Crash code. An initial THUMS validation was performed in order to verify the model-´s biofidelity by means of table-top test simulations. THUMS bone stiffness values were modified to match the real word occupant age. A comparison between driver and passenger restraint system loading was done, as well as an injury prediction comparison between the HIII-dummy model and THUMS response for both cases. Detailed comparison between the HIII-dummy models and THUMS regarding thoracic loading are discussed.
To improve vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility aims to improve both the self and partner protection properties of vehicles. Although compatibility has received worldwide attention for many years, no final assessment approach has been defined. Within the Frontal Impact and Compatibility Assessment Research (FIMCAR) project, different frontal impact test procedures (offset deformable barrier [ODB] test as currently used for Economic Commission for Europe [ECE] R94, progressive deformable barrier test as proposed by France for a new ECE regulation, moveable deformable barrier test as discussed worldwide, full-width rigid barrier test as used in Federal Motor Vehicle Safety Standard [FMVSS] 208, and full-width deformable barrier test) were analyzed regarding their potential for future frontal impact legislation. The research activities focused on car-to-car frontal impact accidents based on accident investigations involving newer cars. Test procedures were developed with both a crash test program and numerical simulations. The proposal from FIMCAR is to use a full-width test procedure with a deformable element and compatibility metrics in combination with the current offset test as a frontal impact assessment approach that also addresses compatibility. By adding a full-width test to the current ODB test it is possible to better address the issues of structural misalignment and injuries resulting from high acceleration accidents as observed in the current fleet. The estimated benefit ranges from a 5 to 12 percent reduction of fatalities and serious injuries resulting from frontal impact accidents. By using a deformable element in the full-width test, the test conditions are more representative of real-world situations with respect to acceleration pulse, restraint system triggering time, and deformation pattern of the front structure. The test results are therefore expected to better represent real-world performance of the tested car. Furthermore, the assessment of the structural alignment is more robust than in the rigid wall test.
The number of injured car occupants decreases constantly. Nevertheless, they account for nearly 50% of all fatalities and about 44% of all seriously injured persons in German traffic accidents. Further reductions of casualties require multiple efforts in all parts of traffic safety. In this paper a detailed analysis of the important pre-hospital rescue phase was done. The basis for future improvements is the knowledge about injury causation of car occupants in combination with other corresponding influence factors. For that reason more than 1.200 severe (AIS3+) injuries of frontal car occupants were analyzed. For the most relevant injuries of car occupants multivariate analysis models were created to predict the probability of these injuries in a real crash scenario. In addition to the collision severity different influence factors like impact direction, seat belt usage, age of the occupant, and gender were analyzed. Furthermore, the models were checked regarding the goodness of fit and all results all results were checked concerning their robustness. The prediction models were created on the basis of 5.000 car accidents. Afterwards, the models were validated using 4.000 different car accidents. The prediction of the probability of severe injuries could be used for different applications in the field of traffic safety. One possibility is the implementation of the models in a tool for the on-the-spot diagnosis. The background for the development of such applications is the fact, that there are only limited diagnostic possibilities available at the accident scene. Nevertheless, the rescue forces have to make essential decisions like the alerting of the necessary medical experts, appropriate treatment, the type of transportation and the choice of an adequate hospital. These decisions quite often decide between life and death or influence the long-term effects of injured persons. At this point, indications of expectable injuries could help enormously. To enable even persons with limited technical knowledge to use the tool, a procedure was developed that facilitates the assumption of the given crash severity. Another important possibility for the application of the prediction models is the use for the qualification of information sent by e-call systems.
This study aimed at developing an injury estimation algorithm for AACN technologies for Germany and compared them to findings based on Japanese data. The data to build and to verify the algorithm was obtained from the German in-depth Accident Database (GIDAS) and split into a training and a validation dataset. Significant input variables and the generalized linear regression model to predict severe injuries (ISS>15) were selected to maximize area under the receiver operating characteristic curve (AUC). Probit regression with the input parameter multiple impact, delta v, seatbelt use and impact direction gave the largest AUC of 0.91. Sensitivity of the algorithm was validated at 90% and specificity at 76% for an injury risk threshold of 2%. It appears that no major differences between Japan and Germany exist for injury estimation based on delta v and impact direction. However, far side impact and multiple crash events appear to be associated with a larger risk increase in the German data.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
India is one of the leading countries reporting highest road accidents & related injuries. TMARG (Tata Motors Accident Research Group) has been recording crashes in association with M/s. Lokamanya Medical Foundation since 2011 with M/s, Amandeep Hospitals since Aug 2013. This study has highlighted some accident types not discussed extensively in literature. Trucks to Truck impacts " Cabin interaction with overhanging loadbody structures and Offset underside impacts for passenger vehicles are seen in significant numbers. The paper discusses these in more detail including severity.
The increasing economics in India has an enormous growth of its road traffic. As observed from official Indian accident statistics the number of road fatalities are one of the highest worldwide. In contrast to most industrialized nations they have an rapidly increasing trend. To come along with this trend it becomes more than essential to understand the traffic accident situation. The official Indian accident statistics gives a glimpse of only basic information. Therefore more detailed data is needed. By using In-depth accident data and officially representative statistics the current accident situation can be evaluated in India, if a suitable weighting methodology is considered. Hence in 2009/2010 a pilot study with the collaboration partner JP-Research India pvt. Ldt. was gathered in Tamil Nadu in south of India. In-depth accident investigations were done around the Coimbatore area on four highways. At first, the collected data is evaluated. Due to consequent and continuous further development based on the first approach a methodology similar to NASS/CDS/GES in the US and GIDAS in Germany was developed. Of course all relevant accident related parameters including pictures and severity information were collected. As a matter of fact based on scaled sketches and reconstruction benefit analyses can be done in order to analyze the accident scenery in India. As a first outcome influence from infrastructure, missing education and vehicle safety were identified as key parameters in order to reduce the number of accidents and casualties. To compare the accident situation against international standards an accident classification for left hand traffic was developed based on the German Insurance classification system. Looking into detail additional accident types were identified and added to create an Indian accident type catalogue. The positive results encouraged several OEMs to participate in this investigation and together with BOSCH a consortium was established in 2010/11. Within one year from beginning in May 2011 about 200 highway accidents were collected, reported and reconstructed using the new standard. Hence a first good overview of the accident situation is available for the Coimbatore Tamil Nadu area. The major target for establishing accident investigations is the extension towards other states of India and urban areas to achieve a better overview of the accident scenery. Therefore local and national authorities have to be embedded in order to strengthen the awareness against traffic safety.