91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (159) (entfernen)
Schlagworte
- Conference (89)
- Konferenz (86)
- Germany (54)
- Deutschland (53)
- Safety (49)
- Sicherheit (48)
- Accident (44)
- Unfall (44)
- Anfahrversuch (41)
- Fahrzeug (38)
Institut
The UN Regulation No. 79 is going to be amended to allow automatically commanded steering functions (ACSF) at speeds above 10 km/h. Hence, requirements concerning the approval of automatically performed steering manoeuvres have to be set in order to allow safe use of automatic steering on public roads as well as improve overall road safety for the driver and the surroundings. By order of the German Federal Ministry of Transport and Digital Infrastructure (BMVI), BASt developed and verified physical test procedures for automatic steering to be implemented in UN Regulation No. 79. The usability of currently available test tools was examined. The paper at hand describes these test procedures and presents results from verification tests. The designated tests are divided in three sections: functionality tests, verifications for the transition of control and emergency tests. System functionality tests are auto matic lane keeping, automatic lane change and an automatic abort of an initiated lane change due to traffic. Those tests check if the vehicle remains in its lane (under normal operating conditions), is able to perform safe automatic lane change manoeuvres and if it considers other road users during its manoeuvres. Transition tests examine the vehicle's behaviour when the driver fails to monitor the system and in situations when the system has to hand over the steering control back to the driver. For instance these tests provoke driver-in-the-loop requests by approaching system boundary limitations, like missing lane markings, surpassing maximum lateral acceleration in a bend or even a major system failure. Even further the driver and his inputs are monitored and if the system detects that he is overriding system actions or contrary want to quit the driving task and unfastens the seat belt, it has to shut down and put the human back into manually control and the responsibility of driving. The last series of test consists of two emergency situations in which the system has to react to a time critical event: A hard decelerating vehicle and a stationary vehicle in front both with no lane change possibility for the ACSF vehicle. Some of the tests, especially the emergency manoeuvres, require special target vehicles and propulsion systems. Since no fully automatic steering vehicles are available, a current Mercedes E-Class with Mercedes' "drive pilot" system was used. It was shown that the vehicle is automatically able to brake to a full stop towards a static Euro NCAP target from partial-automatic driving at 90 km/h, that it could brake towards a rapidly decelerating lead vehicle when travelling at 70 km/h, that it was able during partially automatic driving to remain in its lane in normal operation conditions and to perform a automatic (driver initiated) lane change while surveilling the driver- activities.
Accidents between right turning trucks and straight driving cyclists often show massive consequences. Accident severity in terms of seriously or fatally injured cyclists that are involved is much higher than in accidents of other traffic participants in other situations. It seems clear that adding additional mirrors will very likely not improve the situation. At ESV 2015, a methodology to derive test procedures and first test cases as well as requirements for a driver assist system to address blind spot accidents has been presented. However, it was unclear if and how testing of these cases is feasible, to what extent characteristics of different truck concepts (e.g. articulated vehicles, rigid vehicles) influence the test conduction and outcome, and what tolerances should be selected for the different variables. This work is important for the acceptance of a draft regulation in the UN working group on general safety. In the meantime, three test series using a single tractor vehicle, a tractor-semitrailer combination and a rigid vehicle have been conducted. The test tools (e.g. surrogate devices) have been refined. A fully crashable, commercially available bicycle dummy has been tested. If used correct, this dummy does follow a straight line quite precisely and it does not cause any damage to the truck under test in case of accidental impact. The dummy specifications are freely available. During testing, the different vehicle categories resulted in different trajectories being driven. Articulated vehicle combinations did first execute a turn into the opposite direction, and on the other hand, single tractor vehicles did behave comparable to passenger cars. A possible solution to take these behaviors into account is to require the vehicles to drive through a corridor that is narrow for a precise straight-driving phase and extends during the turn. Other investigated parameters are the dummy and vehicle speed tolerances. The results from this research make it possible to draft a regulation for a driver assistance system that helps to avoid blind spot accidents: test cases have been refined, their feasibility has been checked, and corridors for the vehicles and for important parameters (e.g. test speeds) have been set. The test procedure is applicable to all types of heavy goods vehicles. In combination with the accidentology (ESV 2015 paper), the work provides the basis for a regulation for such an assistance system.
Advancing active safety towards the protection of vulnerable road users: the PROSPECT project
(2017)
Accidents involving Vulnerable Road Users (VRU) are still a very significant issue for road safety. According to the World Health Organisation, pedestrian and cyclist deaths account for more than 25% of all road traffic deaths worldwide. Autonomous Emergency Braking Systems have the potential to improve safety for these VRU groups. The PROSPECT project (Proactive Safety for Pedestrians and Cyclists) aims to significantly improve the effectiveness of active VRU safety systems compared to those currently on the market by expanding the scope of scenarios addressed by the systems and improving the overall system performance. The project pursues an integrated approach: Newest available accident data combined with naturalistic observations and HMI guidelines represent key inputs for the system specifications, which form the basis for the system development. For system development, two main aspects are considered: advanced sensor processing with situation analysis, and intervention strategies including braking and steering. All these concepts are implemented in several vehicle prototypes. Special emphasis is put on balancing system performance in critical scenarios and avoiding undesired system activations. For system validation, testing in realistic scenarios will be done. Results will allow the performance assessment of the developed concepts and a cost-benefit analysis. The findings within the PROSPECT project will contribute to the generation of state -of-the-art knowledge, technical innovations, assessment methodologies and tools for advancing Advanced Driver Assistance Systems towards the protection of VRUs. The introduction of a new generation safety system in the market will enhance VRU road safety in 2020-2025, contributing to the "Vision Zero" objective of no fatalities or serious injuries in road traffic set out in the Transport White Paper. Furthermore, the test methodologies and tools developed within the project shall be considered for the New Car Assessment Programme (Euro NCAP) future roadmaps, supporting the European Commission goal of halving the road toll in the 2011-2020 timeframe.
The presence and performance of Advanced Driver Assistance Systems (ADAS) has increased over last years. Systems available on the market address also conflicts with vulnerable road users (VRUs) such as pedestrians and cyclists. Within the European project PROSPECT (Horizon2020, funded by the EC) improved VRU ADAS systems are developed and tested. However, before determining systems" properties and starting testing, an up-to-date analysis of VRU crashes was needed in order to derive the most important Use Cases (detailed crash descriptions) the systems should address. Besides the identified Accident Scenarios (basic crash descriptions), this paper describes in short the method of deriving the Use Cases for car-to-cyclist crashes. Method Crashes involving one passenger car and one cyclist were investigated in several European crash databases looking for all injury severity levels (slight, severe and fatal). These data sources included European statistics from CARE, data on national level from Germany, Sweden and Hungary as well as detailed accident information from these three countries using GIDAS, the Volvo Cars Cyclist Accident database and Hungarian in-depth accident data, respectively. The most frequent accident scenarios were studied and Use Cases were derived considering the key aspects of these crash situations (e.g., view orientation of the cyclist and the car driver- manoeuvre intention) and thus, form an appropriate basis for the development of Test Scenarios. Results Latest information on car-to-cyclist crashes in Europe was compiled including details on the related crash configurations, driving directions, outcome in terms of injury severity, accident location, other environmental aspects and driver responsibilities. The majority of car-to-cyclist crashes occurred during daylight and in clear weather conditions. Car-to-cyclist crashes in which the vehicle was traveling straight and the cyclist is moving in line with the traffic were found to result in the greatest number of fatalities. Considering also slightly and seriously injured cyclists led to a different order of crash patterns according to the three considered European countries. Finally the paper introduced the Use Cases derived from the crash data analysis. A total of 29 Use Cases were derived considering the group of seriously or fatally injured cyclists and 35 Use Cases were derived considering the group of slightly, seriously or fatally injured cyclists. The highest ranked Use Case describes the collision between a car turning to the nearside and a cyclist riding on a bicycle lane against the usual driving direction. A unified European dataset on car-to-cyclist crash scenarios is not available as the data available in CARE is limited, hence national datasets had to be used for the study and further work will be required to extrapolate the results to a European level. Due to the large number of Use Cases, the paper shows only highest ranked ones.
A reduction of around 48% of all road fatalities was achieved in Europe in the past years including a reduced number of fatalities with an older age. However, among all road fatalities, the proportion of elderly is steadily increasing. In an ageing society, the European (Horizon2020) project SENIORS aims to improve the safe mobility of older road users, who have different transportation habits compared to other age groups. To increase their level of safe mobility by determining appropriate requirements for vehicle safety systems, the characteristics of current road traffic collisions involving the elderly and the injuries that they sustain need to be understood in detail. Hereby, the paper focuses on their traffic participation as pedestrian, cyclist or passenger car occupant. Following a literature review, several national and international crash databases and hospital statistics have been analysed to determine the body regions most frequently and severely injured, specific injuries sustained and types of crashes involved, always comparing older road users (65 years and more) with mid-aged road users (25-64 years). The most important crash scenarios were highlighted. The data sources included European statistics from CARE, data on national level from Germany, Sweden, Italy, United Kingdom and Spain as well as in-depth crash information from GIDAS (Germany), RAIDS (UK), CIREN and NASS-CDS (US). In addition, familiar hospital data from Germany (TraumaRegister DGU-®), Italy (Italian Register of Acute Traumas) and UK hospital statistics (TARN) were included in the study to gain further insight into specific injury patterns. Comprehensive data analyses were performed showing injury patterns of older road users in crashes. When comparing with mid-aged road users, all databases showed that the thorax body region is of particularly high importance for the older car occupant with injury severities of AIS 2 or AIS 3+, whereas the body regions lower extremities, head and thorax need to be considered for the older pedestrians and cyclists. Besides these comparisons, the most frequent and severe top 5 injuries were highlighted per road user group. Further, the most important crash configurations were identified and injury risk functions are provided per age group and road user group. Although several databases have been analysed, the picture on the road safety situation of older road users in Europe was not complete, as only Western European data was available. The linkage between crash data and hospital data could only be made on a general level as their inclusion criteria were quite different.
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.
Test and assessment procedures for passive pedestrian protection based on developments by the European Enhanced Vehicle-safety Committee (EEVC) have been introduced in world-wide regulations and consumer test programmes, with considerable harmonization between these programmes. Nevertheless, latest accident investigations reveal a stagnation of pedestrian fatality numbers on European roads running the risk of not meeting the European Union- goal of halving the number of road fatalities by the year 2020. The branch of external road user safety within the EC-funded research project SENIORS under the HORIZON 2020 framework programme focuses on investigating the benefit of modifications to pedestrian test and assessment procedures and their impactors for vulnerable road users with focus on the elderly. Injury patterns of pedestrians and cyclists derived from the German In-Depth Accident Study (GIDAS) show a trend of AIS 2+ and AIS 3+ injuries getting more relevant for the thorax region in crashes with newer cars (Wisch et al., 2017), while maintaining the relevance for head and lower extremities. Several crash databases from Europe such as GIDAS and the Swedish Traffic Accident Data Acquisition (STRADA) also show that head, thorax and lower extremities are the key affected body regions not only for the average population but in particular for the elderly. Therefore, the SENIORS project is focusing on an improvement of currently available impactors and procedures in terms of biofidelity and injury assessment ability towards a better protection of the affected body regions, incorporating previous results from FP 6 project APROSYS and subsequent studies carried out by BASt. The paper describes the overall methodology to develop revised FE impactor models. Matched human body model and impactor simulations against generic test rigs provide transfer functions that will be used for the derivation of impactor criteria from human injury risk functions for the affected body regions. In a later step, the refined impactors will be validated by simulations against actual vehicle front-ends. Prototyping and adaptation of test and assessment procedures as well as an impact assessment will conclude the work of the project at the final stage. The work will contribute to an improved protection of vulnerable road users focusing on the elderly. The use of advanced human body models to develop applicable assessment criteria for the revised impactors is intended to cope with the paucity of actual biomechanical data focusing on elderly pedestrians. In order to achieve optimized results in the future, the improved test methods need to be implemented within an integrated approach, combining active with passive safety measures. In order to address the developments in road accidents and injury patterns of vulnerable road users, established test and assessment procedures need to be continuously verified and, where needed, to be revised. The demographic change as well as changes in the vehicle fleet, leading to a variation of accident scenarios, injury frequencies and injury patterns of vulnerable road users are addressed by the work provided by the SENIORS project, introducing updated impactors for pedestrian test and assessment procedures.
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
Bus or heavy vehicle passenger accidents are rare events, compared with car accidents, but sometimes leads to a large number of victims especially in rollover crash scenarios. Two accidents occurred in Portugal in 2007 and 2013 in which 28 people died and more than 50 are injured, shown the importance of the investigation of such accidents. For the investigation of these accidents multidisciplinary teams are constituted with engineers and police officers. All the factors involved are taken into consideration including road design, traffic signs, maintenance and hardware, human factors, and vehicle factors. In this work a methodology to an accurate collection of the data is proposed. From the information collected the accident is reconstructed using the PC-CrashTM software. From this all the contribution factors are determined and recommendations to mitigate these crashes are listed. These two accidents are rollover accidents and the analysis of the injuries and its correlation with the use of retention systems is very important. From the medical data and with the dynamics of the accident determined simulations of the occupants with biomechanical models are carried out in order to evaluate the effect of the retention systems in the injuries. This analysis is based on injury criteria (such as Abbreviated Injury Score (AIS) or Injury Severity Scale (ISS)). With this it is possible to determine if the seat belt was worn or not.
Since its creation in 2011 the Pre-Crash-Matrix (PCM) offers the possibility to observe the pre-crash phase until five seconds before crash for a wide range of accidents. Currently the PCM contains more than 8.000 reconstructed accidents out of the GIDAS (German In-Depth Accident Study) database and is enlarged continuously by more than 1.000 cases per year. Hence, a detailed investigation of active safety systems in real accident situations has been made feasible. The PCM contains all relevant data in database format to simulate the pre-crash phase until the first collision of the accident for a maximum of two participants. This includes the definition of the participants and their characteristics, the dynamic behavior of the participants as time-dependent course for five seconds before crash as well as the geometry of the traffic infrastructure. The digital sketch of the accident and information from GIDAS as well as from supplementary databases represent the main input for the simulation of the pre-crash phase of an accident with the VUFO simulation model VAST (Vufo Accident Simulation Tool). This simulation in turn embodies the foundation of the PCM. The PCM underlies continual improvements and enhancements in consultation with its users. In addition to collisions of cars with other cars, pedestrians, bicycles and motorcycles the PCM now also covers car to object and car to truck collisions. The paper illustrates car to truck collisions as a showcase and explains perspectives for further developments. In 2016 a more detailed definition of the contour of the vehicle was added. Furthermore, the geometrical surroundings of the accident site will be provided in a new structure with a higher level of detail. Thus, a precise classification of road marks and objects is possible to further improve the support of developing and evaluating ADAS. This paper gives an overview about the latest developments of the PCM with its innovations and provides an outlook to upcoming enhancements. Besides potential areas of application for the development of ADAS are shown.
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
For more than a decade, ADAC accident researchers have analysed road accidents with severe injuries, recording some 20,000 accidents. An important task in accident research is to determine the causative factors of road accidents. Apart from vehicle engineering and human factors, accident research also focuses on infrastructural and environmental aspects. To find out what accident scenarios are the most common in ADAC accident research and what driver assistance systems can prevent them, our first task was to conduct a detailed accident analysis. Using CarMaker, we performed a realistic simulation of accident scenarios, including crashes, with varying parameters. To begin with, we made an initial selection of driver assistance systems in order to determine those with the greatest accident prevention potential. One important finding of this study is that the safety potential of the individual driver assistance systems can actually be examined. It also turned out that active safety offers even much more potential for development and innovation than passive safety. At the same time, testing becomes more demanding, too, as new systems keep entering the market, many of them differing in functional details. ADAC will continue to test all driver assistance systems as realistically as possible so as to be able to provide advice to car buyers. Therefore, it will be essential to develop and improve test conditions and criteria.
Twenty-eight percent of traffic accidents in Japan are rear-end collisions, and of these, 13% are multiple collisions (three or more vehicles and/or roadside objects). A post-crash braking system enables the driver to stop the vehicle in a short distance after a rear-end collision to prevent secondary collisions. In this study, the effectiveness of a post-crash braking system was examined using a drive recorder database. In 64% of rear-end collisions, the driver's braking was interrupted after the collision. The stopping distance was estimated with time data from the drive recorder. We predict that the brake assist would be effective in preventing secondary collisions in 21% of cases.
Injury probability functions for pedestrians and bicyclists based on real-world accident data
(2017)
The paper is focusing on the modelling of injury severity probabilities, often called as Injury Risk Functions (IRF). These are mathematical functions describing the probability for a defined population and for possible explanatory factors (variables) to sustain a certain injury severity. Injury risk functions are becoming more and more important as basis for the assessment of automotive safety systems. They contribute to the understanding of injury mechanisms, (prospective) evaluation of safety systems and definition of protection criteria or are used within regulation and/or consumer ratings. In all cases, knowledge about the correlation between mechanical behavior and injury severity is needed. IRFs are often based on biomechanical data. This paper is focusing on the derivation of injury probability models from real world accident data of the GIDAS database (German In-depth Accident Study). In contrast to most academic terms there is no explicit term definition or definition of creation processes existing for injury probability models based on empirical data. Different approaches are existing for such kind of models in the field of accident research. There is a need for harmonization in terms of the used methods and data as well as the handling with the existing challenges. These are preparation of the dataset, model assumptions, censored/unknown data, evaluation of model accuracy, definition of dependent and independent variable, and others. In the presented study, several empirical, statistical and phenomenological approaches were analyzed regarding their advantages and disadvantages and also their applicability. Furthermore, the identification of appropriate prediction parameters for the injury severity of pedestrians has been considered. Due to its main effect on injuries of pedestrians and bicyclists, the importance of the secondary impact has also been analyzed. Finally, the model accuracy, evaluated by several criteria, is the rating factor that gives the quality and reliability for application of the resulting models. After the investigation and evaluation of statistical approaches one method was chosen and appropriate prediction variables were examined. Finally, all findings were summarized and injury risk functions for pedestrians in real world accidents were created. Additionally, the paper gives instructions for the interpretation and usage of such functions. The presented results include IRFs for several injury severity levels and age groups. The presented models are based on a high amount of real world accidents and describe very well the injury severity probability of pedestrians and bicyclists in frontal collisions with current vehicles. The functions can serve as basis for the evaluation of effectiveness of systems like Pedestrian-AEB or Bicycle-AEB.
In most of developed countries, the progress made in passive safety during the last three decades allowed to drastically reduce the number of killed and severely injured especially for occupants of passenger cars. This reduction is mainly observed for frontal impacts for which the AIS3+ injuries has been reduced about 52% for drivers and 38% for front passengers. The stiffening of the cars' structure coupled with the generalization of airbags and the improvement of the seatbelt restraint (load limiter, pretension, etc.) allowed to protect vital body regions such as head, neck and thorax. However, the abdomen did not take advantage with so much success of this progress. The objective of this study is to draw up an inventory on the abdominal injuries of the belted car occupants involved in frontal impact, to present adapted counter-measures and to assess their potential effectiveness. In the first part the stakes corresponding to the abdominal injuries will be defined according to types of impact, seat location, occupants' age and type of injured organs. Then, we shall focus on the abdominal injury risk curves for adults involved in frontal impact and on the comparisons of the average risks according to the seat location. In the second part we will list counter-measures and we shall calculate their effectiveness. The method of case control will be used in order to estimate odds ratio, comparing two samples, given by occupants having or not having the studied safety system. For this study, two type of data sources are used: national road injured accident census and retrospective in-depth accident data collection. Abdominal injuries are mainly observed in frontal impact (52%). Fatal or severe abdominal occupant- injuries are observed at least in 27% of cases, ranking this body region as the most injured just after the thorax (51%). In spite of a twice lower occupation rate in the back seats compared to the front seats, the number of persons sustaining abdominal injuries at the rear place is higher than in the front place. In recent cars, the risk of having a serious or fatal abdominal injury in a frontal impact is 1.6% for the driver, 3.6% for the front passenger and 6.3% for the rear occupants. The most frequently hurt organs are the small intestine (17%), the spleen (16%) and the liver (13%). The most common countermeasures have a good efficiency in the reduction of the abdominal injuries for the adults: the stiffness of the structure of the seats allows decreasing the abdominal injury risk from 54% (driver) to 60% (front occupant), the seatbelt pretensioners decrease also this risk from 90% (driver) to 83% (front passenger).
From an automotive safety occupant protection standpoint, effective occupant restraint requires a system capable of providing non-injurious occupant ride down of anticipated crash forces. This is not only the case for frontal collisions, where occupant restraint is provided primarily by seatbelts and airbags, but is also critical for other crash modes such as side impacts, rear impacts, rollovers, as well as multiple impact events. In the rear impact crash mode, occupant restraint is provided primarily by the seatbacks and to some extent the seatbelts. Foundationally, therefore, what becomes fundamental to the seatback's role in rear occupant protection is its ability to contain the occupant within the seat, preventing occupant ramping, as well as preventing the seat's, and/or its occupant's, dangerous intrusion into the rear occupant's survival space where contact with rear compartment components and/ or rear seated occupants can present a significant injury risk. An analysis is presented of a series of rear impact sled testing conducted by the authors that evaluates the timing, position and extent of the front seatback's reward displacement toward and into the rear occupant compartment as well as consideration of the front seat occupant' ramping potential and its injury potential relative to the rear compartment. Additionally, three other series of testing are presented which assess various seat designs occupant retention capabilities. Lastly, a matched-pair comparison test series is presented which evaluates occupant motion in rear impact with and without use of a typical vehicle body mounted 3-point seatbelt. Discussion of restraint system performance observed in all the testing is included along with ATD biofidelity and thigh-gap considerations. The data collected and presented includes accelerometer instrumentation and high speed video analysis.
The incidence of side impacts was investigated from GIDAS data. Both vehicle-fixed object and vehicle-vehicle collisions were analysed as these are enclosed within the consumer testing program. Vehicle-fixed object collisions were stratified according to ESC availability. Results indicated that vehicles equipped with ESC rarely have pure-lateral impacts. An increase in oblique collisions was seen for the vehicles with ESC whereby most vehicle were driving in left curves. The analysis of vehicle-vehicle collisions developed injury risk curves were developed at the AIS3+ injury severity for the vehicle-vehicle side impacts. Results suggested that greatest injury risk occurred when a Pre Euro NCAP vehicle was struck by a Post Euro-NCAP vehicle. The remaining curves did not show different behaviour, indicating that stiffness increased have been equally combated. This was attributable to the few Post Euro-NCAP vehicles that had a deployed curtain airbag available in the sample. The integration of Euro NCAP testing has shown to improve vehicle crashworthiness for pole collisions, as those vehicles with ESC rarely incur lateral impacts.
In 2016 the seventh ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Camera-monitor systems (CMS) can be used in motor vehicles to display the driver's rear view on a monitor mounted inside the vehicle. This also offers the possibility of replacing conventional exterior mirrors with suitable CMS and thereby implementing new design concepts with aerodynamic advantages. However, as exterior mirrors are safety-relevant vehicle parts for securing the driver's indirect rear view (requirements specified in UN Regulation No. 46), the question arises whether CMS can provide an equivalent substitute for mirrors. In the scope of this study, CMS and conventional exterior mirrors were compared and assessed in test drives and static tests under different external conditions. On the one hand, the examination of technical aspects, and on the other hand, issues pertaining to the design of the human-machine interaction, were the objects of the study. Two vehicles were available for the trials with passenger vehicles: A vehicle, manufactured in small series, which is already equipped with CMS as sole replacement for the exterior mirrors, as well as a compact class vehicle which had a CMS retrofitted by the car manufacturer in addition to conventionally used exterior mirrors. The latter could be covered exclusively for trips with CMS. A tractor unit with semitrailer was available for the truck trials. The driver's cabin was equipped with a CMS system developed by the vehicle manufacturer. In general, it was shown that it is possible to display the indirect rear view sufficiently for the driver, both for cars and trucks, using CMS which meet specific quality criteria. Depending on the design, it is even possible to receive more information about the rear space from a CMS than is possible with mirror systems. It was also shown that the change from mirrors to CMS requires a certain period of familiarisation. However, this period is relatively short and does not necessarily result in safety-critical situations.
The market introduction and penetration of electric vehicles can be seen as a milestone in order to reduce the environmental burden imposed by the transport sector. The wide-spread use of electric vehicles powered by electricity from renewable sources promises a substantial reduction of local emissions in urban areas as well as greenhouse gas emissions. To be a successful mobility alternative several obstacles and challenges have to be overcome first. Especially the customers' purchase decision determines finally whether an innovation like electromobility will be successful. Therefore, this paper concentrates on demand-related obstacles and barriers for a broad market deployment of electric cars. Within the Electromobility+ project eMAP these issues are investigated via a consumer survey. It was designed to identify the awareness of potential consumers of electric cars as well as give an estimate of the attitude towards this new technology. In addition to the picture of potential demand-related obstacles the consumers were asked to evaluate the suitability of various promotion measures.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
Within the automotive context camera monitor systems (CMS) can be used to present views of the traffic situation behind the vehicle to the driver via a monitor mounted inside the cabin. This offers the opportunity to replace classical outside rearview mirrors and therefore to implement new design concepts, aerodynamically optimized vehicle shapes and to reduce the width of the vehicle. Further, the use of a CMS offers the potential to implement functionalities like warnings or situation-adaptive fields of view that are not feasible with conventional rearview mirrors. Despite these potential advantages, it is important to consider the possible technical constraints of this technology and its effect on driver perception and behavior. On the technical side next to the field of view and die robustness of die system, aspects as its functionality at day and night as well as under varying weather conditions should be object to scientific investigation. Concerning human machine interaction, it has to be considered, that the perception of velocities and distances of approaching vehicles might be different for CMS as compared to conventional rearview mirrors and potential influences of factors as the Position of the displays or drivers' age should be taken into account. In order to shed light on these and further open issues, BASt is currently conducting a study that will cover the use of CMS under controlled conditions as well in real traffic. The first part of the study will focus on passenger cars, while in a second step the empirical investigation will be extended to heavy goods vehicles, where the potentials as well as the limitations of CMS might differ considerably. The presentation will cover the first part, with regard to the experimental design, implementation and initial results if already available.
To improve vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility aims to improve both the self and partner protection properties of vehicles. Although compatibility has received worldwide attention for many years, no final assessment approach has been defined. Within the Frontal Impact and Compatibility Assessment Research (FIMCAR) project, different frontal impact test procedures (offset deformable barrier [ODB] test as currently used for Economic Commission for Europe [ECE] R94, progressive deformable barrier test as proposed by France for a new ECE regulation, moveable deformable barrier test as discussed worldwide, full-width rigid barrier test as used in Federal Motor Vehicle Safety Standard [FMVSS] 208, and full-width deformable barrier test) were analyzed regarding their potential for future frontal impact legislation. The research activities focused on car-to-car frontal impact accidents based on accident investigations involving newer cars. Test procedures were developed with both a crash test program and numerical simulations. The proposal from FIMCAR is to use a full-width test procedure with a deformable element and compatibility metrics in combination with the current offset test as a frontal impact assessment approach that also addresses compatibility. By adding a full-width test to the current ODB test it is possible to better address the issues of structural misalignment and injuries resulting from high acceleration accidents as observed in the current fleet. The estimated benefit ranges from a 5 to 12 percent reduction of fatalities and serious injuries resulting from frontal impact accidents. By using a deformable element in the full-width test, the test conditions are more representative of real-world situations with respect to acceleration pulse, restraint system triggering time, and deformation pattern of the front structure. The test results are therefore expected to better represent real-world performance of the tested car. Furthermore, the assessment of the structural alignment is more robust than in the rigid wall test.
Assessment of the effectiveness of Intersection Assistance Systems at urban and rural accident sites
(2015)
An Intersection Collision Avoidance System is a promising safety system for accident avoidance or injury mitigation at junctions. However, there is still a lack of evidence of the effectiveness, due to the missing real accident data concerning Advanced Driver Assistance Systems. The objective of this study is the assessment of the effectiveness of an Intersection Collision Avoidance System based on real accidents. The method used is called virtual pre-crash simulation. Accidents at junctions were reconstructed by using the numerical simulation software PC-Crashâ„¢. This first simulation is called the baseline simulation. In a second step the vehicles of these accidents were equipped with an Intersection Collision Avoidance System and simulated again. The second simulation is called the system simulation. In the system simulation two different sensors and four different intervention strategies were used, based on a time-to-collision approach. The effectiveness of Intersection Collision Avoidance System has been evaluated by using an assessment function. On average 9% of the reviewed junction accidents could have been avoided within the system simulations. The other simulation results clearly showed a change in the principal direction of force, delta-v and reduction of the injury severity.
Event data recorders (EDRs) are a valuable tool for in-depth investigation of traffic accidents. EDRs are installed on the airbag control module (ACM) to record vehicle and occupant information before, during, and after a crash event. This study evaluates EDR characteristics and aims at better understanding EDR performance for the improvement of accident reconstruction with more reliable and accurate information regarding accidents. The analysis is based on six crash tests with corresponding EDR datasets.
The Traffic Accident Research Institute at University of Technology Dresden investigates about 1,000 accidents annually in the area around and in Dresden. These datasets have been summarized and evaluated in the GIDAS (German Accident In-Depth Study) project for 13 years. During the project it became apparent that the specific traffic situation of a covert exit of a passenger car and an intersecting two-wheeler involves a high risk potential. This critical situation develops in a large part due to the lack of visibility between the driver and the intersecting bike. In this paper the accident avoidance potential of front camera systems with lateral field of view, which allows the driver to have an indirect sight into the crossing street area will be presented.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
Regarding to the German road traffic licensing regulations it is mandatory to have a light system using a bicycle in public traffic. All attached components must be approved. The admission requires additional restrictions such as a dynamo as energy source with a nominal voltage of 6 V. Batteries are only allowed in addition to this. To adopt the German bicycle regulation to the state of art of an energy efficient lighting, additional power sources such as a battery respectively rechargeable batterie should be evaluated. The project will propose amendments for German Road Traffic Regulations and technical requirements.
This study aimed at developing an injury estimation algorithm for AACN technologies for Germany and compared them to findings based on Japanese data. The data to build and to verify the algorithm was obtained from the German in-depth Accident Database (GIDAS) and split into a training and a validation dataset. Significant input variables and the generalized linear regression model to predict severe injuries (ISS>15) were selected to maximize area under the receiver operating characteristic curve (AUC). Probit regression with the input parameter multiple impact, delta v, seatbelt use and impact direction gave the largest AUC of 0.91. Sensitivity of the algorithm was validated at 90% and specificity at 76% for an injury risk threshold of 2%. It appears that no major differences between Japan and Germany exist for injury estimation based on delta v and impact direction. However, far side impact and multiple crash events appear to be associated with a larger risk increase in the German data.
The current Brussels EU Regulation No. 1235/2011, valid from May 30, 2012, has introduced an European Tyre Label with wet grip index G classes from A to G for passenger car tyres C1, light commercial vehicles tyres C2 and heavy truck- and bus tyres C3. Every wet grip class for each vehicle category has a defined band of numerical values for the wet grip index G. The legislated wet grip values G in this EU- Regulation are very low. The measured braking distances and corresponding impact speeds of the test vehicles are showing very critical results. Regulation No. 1235/2011 of the European Parliament and the Council for Type Approval of Vehicles (EU) should be changed in such a way, that for C1-tyres (normal passenger cars tyres) the minimum wet grip index G is 1.25. All C2-tyres (light commercial vehicles tyres) should at least meet a minimum wet grip index of G = 1.1. All C3-tyres (heavy trucks and buses tyres) should at least meet a minimum wet grip index of G = 0.95. Due to the missing lower limits for G in the wet grip class F for C1, C2 and C3 tyres according to Commission Regulation (EU) No. 1235/2011, officially valid from 30 May 2012, a tyre-to-road coefficient of adhesion in the extreme of 0 (zero) is legally permitted. This is an apparent flaw in above cited EU Regulation, which causes a potential danger to the road traffic safety for all motor vehicles in Europe with such tyres. The wet grip class F has to be removed urgently from said EURegulation, since a direct liability of the responsible EU-Commission can not be excluded.
Today's volumes of traffic require more and more responsibility from each individual road user in their interactions. Those who drive motor vehicles have the singular obligation to minimise the risk of accidents and hence the severity of injuries, particularly with a view to the most vulnerable road users such as motor bikes, bikes and pedestrians. Since responsible and pro-active driving depends first and foremost on the visual information relayed by our eyes and the visual channel this requires good command of the traffic and all-round visibility from our driver's seat. Granted that human error can never be fully excluded, improving visibility around the car is nevertheless an urgent priority. To do so, we need to rate visibility in the most realistic driving situations. Since the existing visibility metrics and methodology are not applicable to real-life driving situations, this study aimed at developing a new visibility rating methodology based on real-life accident scenarios. On the basis of the cases documented by the accident research project, this study analysed criteria indicative of diminishing visibility on the one hand and revealing some peculiarities in connection with the visibility issue on the other. Based on the above, the project set out to develop a rating methodology allowing to assess all-round visibility in various road situations taking into account both driver and road geometries. In this context, the assessment of visibility while turning a corner, crossing an intersection and joining traffic on a major road (priority through route) is of major importance. The first tests have shown that critical situations can be avoided by adapting the relevant geometries and technical solutions and that significant improvements of road safety can be derived therefrom.
For the estimation of the benefit and effect of innovative Driver Assistance Systems (DAS) on the collision positions and by association on the accident severity, together with the economic benefit, it becomes necessary to simulate and evaluate a variety of virtual accidents with different start values (e.g. initial speed). Taken into account the effort necessary for a manual reconstruction, only an automated crash computation can be considered for this task. This paper explains the development of an automated crash computation based on GIDAS. The focus will be on the design of the virtual vehicle models, the method of the crash computation as well as exemplary applications of the automated crash computation. For the first time an automated crash computation of passenger car accidents has been realized. Using the automated crash computation different tasks within the field of vehicle safety can be elaborated. This includes, for example, the calculation of specific accident parameters (such as EES or delta-V) for various accident constellations and the estimation of the economic benefit of DAS using IRFs (Injury Risk Functions).
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
The paper gives an overview of the recent (mostly 2012) figures of killed bus/coach occupants (drivers and passengers) in 27 Member States of the European Union as reported by CARE. The Evolution of the figures of bus/coach occupants killed in road accidents urban, rural without motorway and on motorways from 1991 to 2010 in 15 Member States of the EU supplements this information. More detailed are the figures reported for Germany by the Federal Statistics. The paper displays long-term evaluations (1957 to 2012) for killed, seriously and slightly injured occupants in all kinds of buses/coaches. Midterm evaluations (1995 to 2012) of the figures of fatalities and casualties are displayed for different busses according to their identification of road using as coaches, urban buses, school buses, trolley buses and "other buses". To be able to compare the evolutions of the safety of vehicle occupants it is customary to use different risk indicators. Calculations and illustrations for three often used indicators with their development over time are given: fatalities, seriously injured and slightly injured per 100,000 vehicles registered, per 1 billion (109) vehicle-kilometres travelled and per 1 billion (109) person-kilometres. These indicators are shown for occupants of cars, goods vehicles and buses/coaches. For the period from 1957 until 2012 it is obvious, that for all three vehicle categories analysed there was a clear long-term trend towards more occupant safety in terms of casualties per vehicles registered and per vehicle mileage. This was most significant for car occupants but it can be seen for bus/coach occupants and goodsvehicle occupants as well. Figures of killed occupants and of casualties related to person-kilometres are calculated and displayed for the shorter period 1995 to 2012. Here it becomes obvious that the bus/coach is still the safest mode of transport for the occupants of road vehicles. Graphs for the casualty risk indices still show significantly higher risks for car occupants despite the corresponding curve moved sustainable downwards. It is remarkable, that the risks of being killed or injured for the occupants of urban buses is growing whereas the corresponding risk for the occupants of coaches in line traffic tends downwards. The article ends with a short comparison and discussion of the risk indicators which are actually published for the occupants (driver and passengers) of cars and the passengers of buses/coaches, railroads, trams and airplanes. The interpretation of such information depends on the perception and it seems that for a complete view not only one indicator should be used and the evolutions of the indicator values during longer periods (as displayed with examples in the paper) should also be taken into account.
This work aimed for getting the main features of accidents involving Light Goods Vehicles (LGV), using accident cases collected in the In-Depth Accidents Studies built up at IFSTTAR-LMA (France), in order to analyse thoroughly the proceedings of these accidents and identify the major factors for the different types of LGV. This work was based on the analysis of 88 accident cases involving LGV with a Maximum Authorised Mass inferior to 3.5 tonnes. In particular kinematics reconstruction of these accidents were performed to calculate the average impact speeds and to better understand the compatibility problems between LGV and antagonist vehicles. Specific features have been reviewed to pick up problems concerning safety, maintenance, loading, LGV design: general conditions of the accident, vehicle features, and passive safety. The main results of this study are presented in this paper.
In 2014 the sixth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
EEVC Status report
(2001)
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
A means of assessing the passive safety of automobiles is a desirable instrument for legislative bodies, the automobile industry, and the consumer. As opposed to the dominating motor vehicle assessment criteria, such as engine power, spaciousness, aerodynamics and consumption, there are no clear and generally accepted criteria for assessing the passive safety of cars. The proposed method of assessment combines the results of experimental safety tests, carried out according to existing legally prescribed or currently discussed testing conditions, and a biomechanical validation of the loading values determined in the test. This evaluation is carried out with the aid of risk functions which are specified for individual parts of the body by correlating the results of accident analysis with those obtained by computer simulation. The degree of conformance to the respective protection criterion thus deduced is then weighted with factors which take into account the frequency of occurrence and the severity of the accident on the basis of resulting costs. Each of the test series includes at least two frontal and one lateral crash test against a deformable barrier. The computer-aided analysis and evaluation of the simulation results enables a vehicle-specific overall safety index as well as partial and individual safety values to be determined and plotted graphically. The passive safety provided by the respective vehicle under test can be defined for specific seating positions, special types of accident, or for individual endangered parts of the body.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of plastic materials as a material for the interior equipment of buses and coaches due to their good mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years " also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, also the production of smoke, the smoke development and propagation as well as its toxicity are of interest. That counts for the passengers as well as for the test methods and its limit values. The severe fire in Germany near Hanover in 2008 with 20 fatalities showed how disastrous such fires can be. For those reasons several research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behaviour of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and onboard extinguishing equipment were elaborated. On the other hand research was carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. In this project small and real scale experiments on material specimens, interior parts and vehicles were performed. Trains and buses often have very similar operation conditions. Consequently, bus interior material was tested according to the regulations for rail vehicles, i.e. DIN EN 45545 as well as DIN 5510. None of the tested bus interior materials would have been allowed to use in a train. The fire safety regulations for bus materials are on a low level compared to other transport sectors, i.e. railway, ship and aircraft. Also numerical investigations with the Fire Dynamics Simulator (FDS) were performed. The very rapid fire development during the severe bus fire from 2008 could be predicted with the numerical model. The model was then used to investigate the influence of different materials, ventilation conditions and ignition sources. The bus materials contribute significantly to a very rapid fire development in bus fires. Especially, the flammable ceiling and the passenger seats were identified to be key issues of the fire propagation in a bus and can be explained by the rapid fire spread along the ceiling and the high fire load of passenger seats. As conclusion of the project effective and economically reasonable fire safety requirements for interiors of buses are recommended which would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
The development of tyre- and truck-manufacturers leads to the direction to introduce wide base single tyres (size 495/45R22,5) instead of twin tyres on the driving axle of trucks, tractors and busses. To study the driving behaviour and safety of various trucks and units with different tyre combinations and loading conditions was the aim of the study. A computer-aided simulation was used for this investigation. Drive tests with a 40 t unit with prototype single tyres on the drive axle were carried out to verify the simulation. Alterations in driving behaviour and driving safety are mainly dependent on the tyre cornering stiffness. The prototype wide single tyres had a higher lateral stiffness which leads to a higher degree of under-steering (safer driving behaviour). The altered spring base on the drive axle had no influence on the side- tilt stability of vehicle combinations but the solo truck profited from the higher rear axle roll stiffness (less danger for roll-over accidents). As far as the driving safety is concerned nothing speaks against wide base tyres on the drive axle. The simulation of a tyre defect in a bend (assuming 40% of the max. transferable side force for the flat tyre) showed no increased danger using wide single tyres. Later driving tests showed however the need of tyre run flat possibilities to avoid jack-knifing of road trains. Also tyre pressure monitoring systems and electronic stability programs for the trucks are advised.