91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (164)
- Buch (Monographie) (111)
- Wissenschaftlicher Artikel (18)
- Arbeitspapier (13)
- Teil eines Buches (Kapitel) (8)
- Bericht (5)
Schlagworte
- Deutschland (138)
- Germany (138)
- Safety (124)
- Sicherheit (123)
- Conference (101)
- Konferenz (98)
- Fahrzeug (89)
- Vehicle (88)
- Research report (77)
- Forschungsbericht (75)
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
The objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria and limits for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configurations such as impacts with car sides, trucks, and pedestrians. The WG consists of national government representatives who are supported by industrial advisers. The WG serves as a focal point for European research conducted by national and industry sponsored projects. The WG is responsible for collating the results from this research to achieve its objectives. EEVC WG 15 serves as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the Development of Crash Test Procedures"(VC-COMPAT) project partly funded by the European Commission. This paper presents a review of the current European research status. It also identifies current issues with candidate test procedures and lists the parameters that should be considered in assessing compatibility. The current candidate test procedures are: an offset barrier test with the progressive deformable barrier (PDB) face; a full width wall test with or without a deformable aluminium honeycomb face and a high resolution load cell wall; an offset barrier test with the EEVC barrier and load cell wall. These candidate test procedures must allow assessment of structural interaction, frontal force levels and compartment strength. The WG will report its findings to the EEVC Steering Committee and propose a test procedure in November 2006.
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
Die EU hat für die Verkehrssicherheit in Europa ein anspruchsvolles Ziel vorgegeben: Bis 2010 soll die Anzahl der im Straßenverkehr Getöteten gegenüber 2000 halbiert werden. Für Deutschland kann eine erfolgreiche Zwischenbilanz gezogen werden: In den letzten 5 Jahren nahm trotz Vergrößerung des Kraftfahrzeugbestandes um 6% die Anzahl der Verkehrstoten um 29% ab, in den vergangenen 10 Jahren ist ein Rückgang um 43% zu verzeichnen. Diese im internationalen Vergleich überdurchschnittlichen Erfolge sind nicht zuletzt auch auf Fortschritte in der Fahrzeugtechnik zurückzuführen, wobei die zunehmende Verbreitung von Systemen der Aktiven Sicherheit wie ABS, BAS, ESP einen entscheidenden Anteil hat. Nach der deutlichen Reduzierung von Fahrunfällen durch ESP-® stehen nun die Auffahrunfälle im Fokus der Sicherheitsentwicklung von Mercedes-Benz. Das Paket aus verbessertem rückwärtigen Signalbild (Adaptives Bremslicht) und Brems-Assistent (BAS) wurde kürzlich durch radarbasierte Bremsassistenz ergänzt (BAS PLUS und PRE-SAFE-®-Bremse). Der Beitrag geht auf Funktion und Wirksamkeit der einzelnen Systeme ein und gibt einen Ausblick in die nähere Zukunft.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
Das Ziel der Untersuchung war, die Grenzen der Belastbarkeit eines Rollstuhl- und Personenrückhaltesystems mit Kraftknoten nach DIN 75078-2 zu ermitteln. Dazu wurden dynamische Schlittenversuche durchgeführt, bei denen die Verzögerungspulse sowie das Gesamtgewicht von Rollstuhl und Prüfpuppe variiert wurden. Für die Untersuchungen kamen ein Prüfrollstuhl, definiert nach ISO 10542, und Rückhaltesysteme mit Kraftknoten gemäß DIN 75078-2 zum Einsatz. Das Rückhaltesystem bestand aus einem Rollstuhl- und einem Personenrückhaltesystem, wobei das Rollstuhlrückhaltesystem (RRS) mit vier bzw. sechs Gurten und entsprechenden Retraktoren an einem dynamischen Schlittenaufbau befestigt wurde. Das Personenrückhaltesystem (PRS) bestand aus einem am Rollstuhl integrierten Beckengurt sowie einem Schulterschräggurt, der am Beckengurt und am Schlittenaufbau befestigt wurde. Ferner wurden bei den Versuchen Prüfpuppen verschiedener Alters- und Gewichtsklassen (P6, HIII 5 %, HIII 50 % und HIII 95 %) eingesetzt Die Belastungsanforderungen für das Rückhaltesystem wurden sukzessiv erweitert, indem einerseits das Gesamtgewicht (Rollstuhl und Prüfpuppe) und andererseits auch die Verzögerungspulse bis zur Versagensgrenze erhöht wurden. Das Vier-Gurt-Rückhaltesystem konnte bei einem Verzögerungspuls von 10 g einem Gesamtgewicht von bis zu 221 kg standhalten. Bei einem Verzögerungspuls von 20 g und einem Gesamtgewicht von 134 kg wurde das Vier-Gurt-System bis über die Grenzen belastet. Das Sechs-Gurt-Rückhaltesystem hat Belastungen bis 221 kg standgehalten. Infolgedessen ist bei einer Erhöhung der Verzögerungspulse auf 20 g und einem Gesamtgewicht von mehr als 109 kg ein Sechs-Gurt-System zu empfehlen.
The UN Regulation No. 79 is going to be amended to allow automatically commanded steering functions (ACSF) at speeds above 10 km/h. Hence, requirements concerning the approval of automatically performed steering manoeuvres have to be set in order to allow safe use of automatic steering on public roads as well as improve overall road safety for the driver and the surroundings. By order of the German Federal Ministry of Transport and Digital Infrastructure (BMVI), BASt developed and verified physical test procedures for automatic steering to be implemented in UN Regulation No. 79. The usability of currently available test tools was examined. The paper at hand describes these test procedures and presents results from verification tests. The designated tests are divided in three sections: functionality tests, verifications for the transition of control and emergency tests. System functionality tests are auto matic lane keeping, automatic lane change and an automatic abort of an initiated lane change due to traffic. Those tests check if the vehicle remains in its lane (under normal operating conditions), is able to perform safe automatic lane change manoeuvres and if it considers other road users during its manoeuvres. Transition tests examine the vehicle's behaviour when the driver fails to monitor the system and in situations when the system has to hand over the steering control back to the driver. For instance these tests provoke driver-in-the-loop requests by approaching system boundary limitations, like missing lane markings, surpassing maximum lateral acceleration in a bend or even a major system failure. Even further the driver and his inputs are monitored and if the system detects that he is overriding system actions or contrary want to quit the driving task and unfastens the seat belt, it has to shut down and put the human back into manually control and the responsibility of driving. The last series of test consists of two emergency situations in which the system has to react to a time critical event: A hard decelerating vehicle and a stationary vehicle in front both with no lane change possibility for the ACSF vehicle. Some of the tests, especially the emergency manoeuvres, require special target vehicles and propulsion systems. Since no fully automatic steering vehicles are available, a current Mercedes E-Class with Mercedes' "drive pilot" system was used. It was shown that the vehicle is automatically able to brake to a full stop towards a static Euro NCAP target from partial-automatic driving at 90 km/h, that it could brake towards a rapidly decelerating lead vehicle when travelling at 70 km/h, that it was able during partially automatic driving to remain in its lane in normal operation conditions and to perform a automatic (driver initiated) lane change while surveilling the driver- activities.
At IAM RoadSmart we share the excitement about autonomous cars " who wouldn't! However over half of the drivers we polled supported concentrating on making drivers safer " among IAM RoadSmart members it was 70%. Driverless cars are still years away but delivering safer drivers can help reduce death and injury from tomorrow. Governments, academics and car makers need to work hard to convince sceptical British and American drivers that autonomous cars can deliver the benefits promised such as a 90% plus reduction in road deaths.
Das von der Bundesanstalt für Straßenwesen in Auftrag gegebene Projekt FP 8716 mit dem Thema "Sicherheitsrelevanz neuer Fahrhilfen in Kraftfahrzeugen" ist vom Institut für Kraftfahrwesen der TH Aachen auf der Basis einer rein theoretischen Studie bearbeitet worden. Primäres Ziel der Arbeit war es, festzustellen, inwieweit die neuen Fahrhilfen dazu geeignet sind, die Verkehrssicherheit durch einen Gewinn an aktiver Sicherheit anzuheben.Aber auch der mögliche Einfluss auf das Verhalten des Fahrers aus psychologischer Sicht war zu berücksichtigen, denn dieser agiert in dem Bewusstsein einer erhöhten Fahrsicherheit seines mit derartigen Systemen ausgestatteten Fahrzeugs. Gegenstand der Untersuchung waren die Systeme: Anti-Blockier-Vorrichtung (ABV), Antriebs-Schlupf-Regelung (ASR), Sperrdifferential, Vierradantrieb, Vierradlenkung, geregeltes/gesteuertes Federungssystem.Sämtliche Systeme haben aus der Sicht des Technikers ihre Berechtigung im Fahrzeug durch Erhöhung von Mobilität und Fahrsicherheit. Dass dieses Potential nicht vollständig in eine Anhebung der Verkehrssicherheit umgesetzt werden kann, ist vor allem auf die Verhaltensanpassung seitens des Fahrers aufgrund des erhöhten subjektiven Sicherheitsgefühls zurückzuführen. Anhand von Handlungs- und Risikoverhaltensmodellen des Fahrers konnte die verbleibende Wirkung der Systeme abgeschätzt werden. Darüber hinaus wurde statistisches Material ausgewertet, um den Bezug der Systeme zum Unfallgeschehen festzustellen. Das ABV erwies sich als am ehesten geeignet, Unfälle zu verhindern oder Unfallfolgen zu mindern. Die Stabilität und die Lenkbarkeit wird bei Bremsungen an der Kraftschlussgrenze, wie sie in kritischen Situationen häufig auftreten, deutlich verbessert. Eine ASR bietet ähnliche Vorteile beim Beschleunigungsvorgang, dem allerdings nur eine geringe Bedeutung für die Pre-Crash-Phase zuzuschreiben ist. Das Sperrdifferential dient in erster Linie zur Erhöhung der Traktion und damit der Mobilität. Daneben kann der Vierradantrieb die Querdynamik auf niedrigen Reibwerten günstig beeinflussen und so auch die Fahrsicherheit anheben. Das verspricht auch die Vierradlenkung durch eine erhöhte Stabilität bei schnellen Lenkbewegungen. Es besteht aber gerade bei den Systemen Vierradlenkung und Vierradantrieb die Gefahr einer deutlichen Zunahme des subjektiven Sicherheitsgefühls auf Seiten des Fahrers mit dem unerwünschten Effekt einer unter Umständen riskanteren Fahrweise. Geregelte Federungssysteme sind in ihrer Wirkung auf den Regelkreis Fahrer-Fahrzeug nur schwer einzuschätzen, da sie das gesamte Fahrverhalten des Fahrzeugs beeinflussen. Die Bilanz für die Verkehrssicherheit dürfte bei diesem System positiv sein. Dem Gewinn an Fahrsicherheit durch den Einbau der Fahrhilfen steht das Gefährdungspotential durch eventuelle Fehlfunktionen gegenüber. Eine regelmäßige Überwachung erscheint deshalb vor allem für die ABV und die Vierradlenkung angebracht.
In der Europäischen Union (EU) gab es 1999 circa 1,3 Millionen Straßenverkehrsunfälle mit Personenschaden, wobei circa 42.000 Personen getötet wurden. Ziel der EU ist es diese Zahl auf 25.000 im Jahr 2010 zu senken. Die EEVC befasst sich bereits seit Anfang der 80er Jahre mit der Thematik Fußgängerschutz in verschiedenen Arbeitsgruppen. Im Dezember 1998 legte die EEVC-Arbeitsgruppe 17 "Fußgängersicherheit" ihren Abschlussbericht vor, in dessen Anhang ein Prüfverfahren zum fahrzeugseitigen Fußgängerschutz enthalten ist. Dieses Prüfverfahren wird vorgestellt. Es basiert auf Komponententests. Unterschieden werden drei Prüfkörperarten und insgesamt vier Prüfkörper. Aus wissenschaftlicher Sicht und aus Sicht der Unfallforschung empfiehlt die EEVC-Arbeitsgruppe 17 eine umfassende Einführung des vorgeschlagenen Prüfverfahrens mit allen Prüfkörpern, gegebenenfalls in Form einer stufenweisen Einführung.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
Except for corrective steering functions automatic steering is up to now only allowed at speeds up to 10 km/h according to UN Regulation No. 79. Progress in automotive engineering with regard to driver assistance systems and automation of driving tasks is that far that it would be technically feasible to realise automatically commanded steering functions also at higher vehicle speeds. Besides improvements in terms of comfort these automated systems are expected to contribute to road traffic safety as well. However, this safety potential will only be exhausted if automated steering systems are properly designed. Especially possible new risks due to automated steering have to be addressed and reduced to a minimum. For these reasons work is currently ongoing on UNECE level with the aim to amend the regulation dealing with provisions concerning the approval of steering equipment. It is the aim to revise requirements for automatically commanded steering functions (ACSF) so that they can be approved also for higher speeds if certain performance requirements are fulfilled. The paper at hand describes the derivation of reasonable system specifications from an analysis of relevant driving situations with an automated steering system. Needs are explained with regard to covering normal driving, sudden unexpected critical events, transition to manual driving, driver availability and manoeuvres to reach a state of minimal risk. These issues form the basis for the development of test procedures for automated steering to be implemented in international regulations. This holds for system functionalities like automatic lane keeping or automatic lane change as well as for addressing transition situations in which the system has to hand over steering to the driver or addressing emergency situations in which the system has to react instead of the driver.
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
The objective was to develop and validate a crash trolley (reference vehicle) equipped with a compartment and a full restraint system for driver and front seat passenger which can be used in full scale crash testing. Furthermore, the crash trolley should have a suspension to show rotation and nick effects similar to real vehicles. Within the development phase the reference vehicle was build based on a European family car. Special attention was needed to provide appropriate strength to the trolley and its suspension. The reference vehicle is equipped with a restraint system consisting of airbags, pedals, seats, dashboard, and windscreen. On the front of the vehicle different crash barriers can be installed to provide miscellaneous deceleration pulses. For the validation phase a series of low and high speed crash tests with HIII dummies were conducted and compared with full scale tests. For the comparison deceleration pulse, dummy numbers and vehicle movement were analyzed. Validation tests with velocities up to 60 km/h showed promising results. The compartment and the suspension systems stayed stable. Rotation effects were comparable with full scale car crash tests. The airbags and seat belt system worked reasonable. The acceleration pulse compared to an Euro NCAP test had a similar characteristic but was in general slightly lower. After the successful validation the reference vehicle is already in use in different studies in the field of vehicle safety research at BASt.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
In der Europäischen Gemeinschaft werden derzeit jährlich ca. 50.000 Menschen bei Verkehrsunfällen getötet, ca. 10.000 davon als Fußgänger. Von den 10.600 (1992) in der Bundesrepublik Deutschland bei Straßenverkehrsunfällen Getöteten waren 1.800 Fußgänger (etwa 17 Prozent). Problemgruppen bei Fußgängerunfällen bilden die Kinder wegen ihrer hohen Unfallhäufigkeit und alte Personen wegen ihrer hohen Unfallschwere. Kopfverletzungen sind die häufigste Todesursache bei Fußgängerunfällen. Eine Verringerung der Unfallschwere kann - außer durch Verminderung von Fahr- beziehungsweise Aufprallgeschwindigkeiten der Fahrzeuge - nur durch konstruktive Eingriffe an der vorderen Fahrzeugaußenkontur oder dem Unterbau von Pkw erfolgen. Dazu ist es notwendig, einheitliche Prüfverfahren für die Beurteilung der "Fahrzeugaggressivität" gegenüber Fußgängern bereitzustellen. Die Ableitung eines Prüfvorschlages zur Simulation des Kopfaufpralls auf Fronthauben von Pkw beim Fußgängerunfall, unterteilt in Kopfaufpralltests für Erwachsene und Kinder, ist Gegenstand dieser Arbeit. Es werden, ausgehend von einer Analyse der Unfallstatistik, der Entstehungsmechanismus von Kopfverletzungen erklärt, die für ein Prüfverfahren notwendigen Eingangsparameter (Masse, Geschwindigkeit, Aufprallstellen am Fahrzeug etc.) abgeleitet und die Ergebnisse der gewählten Prüfkörpertestmethode mit Ergebnissen von Leichenversuchen verglichen. Eine Kosten-/Nutzen-Betrachtung am Schluss der Arbeit zeigt, dass sich bei nur geringen Kosten ein volkswirtschaftlicher Nutzen durch eine allgemeine Anwendung des Prüfverfahrens mit ca. 270 Millionen DM allein in der Bundesrepublik Deutschland pro Jahr erzielen ließe.
Die Reduzierung des Verkehrslärms ist eine große Herausforderung für alle Beteiligten. Das gilt umso mehr, als nach den Prognosen sich die Verkehrsleistung auf der Straße noch stark erhöhen wird. Viele Stellen in Deutschland, wie Industrie, Forschungseinrichtungen und Behörden haben sich der Problematik angenommen. Forschungsarbeiten wurden und werden durchgeführt oder sind in Vorbereitung. Über die nationalen Aktivitäten hinaus wird das Thema europaweit behandelt. In vier Beiträgen wird über die europäischen Forschungsprojekte SILVIA, ITARI, SILENCE und P2RN berichtet. Das Spektrum der Konzepte dieser Forschungsarbeiten ist sehr breit und erstreckt sich über praktische und theoretische Ansätze.
The incidence of side impacts was investigated from GIDAS data. Both vehicle-fixed object and vehicle-vehicle collisions were analysed as these are enclosed within the consumer testing program. Vehicle-fixed object collisions were stratified according to ESC availability. Results indicated that vehicles equipped with ESC rarely have pure-lateral impacts. An increase in oblique collisions was seen for the vehicles with ESC whereby most vehicle were driving in left curves. The analysis of vehicle-vehicle collisions developed injury risk curves were developed at the AIS3+ injury severity for the vehicle-vehicle side impacts. Results suggested that greatest injury risk occurred when a Pre Euro NCAP vehicle was struck by a Post Euro-NCAP vehicle. The remaining curves did not show different behaviour, indicating that stiffness increased have been equally combated. This was attributable to the few Post Euro-NCAP vehicles that had a deployed curtain airbag available in the sample. The integration of Euro NCAP testing has shown to improve vehicle crashworthiness for pole collisions, as those vehicles with ESC rarely incur lateral impacts.
Ausgehend von den Unfalldaten der letzten Jahre wird die Bedeutung von Fußgängerunfällen im Unfallgeschehen dargestellt. Betrachtet man die bei Unfällen getöteten Verkehrsteilnehmer, so sind am häufigsten Personen in Kraftfahrzeugen betroffen. Am zweithäufigsten werden, gemäß der Unfallstatistik, Fußgänger getötet. Eine Möglichkeit zur Verbesserung des Schutzes von Fußgängern und anderen sogenannten "ungeschützten Verkehrsteilnehmern" im Falle einer Kollision mit einem Kraftfahrzeug sind Maßnahmen am Fahrzeug. Um die Wirksamkeit derartiger Maßnahmen zu beurteilen, wurde durch das EEVC (European Enhanced Vehicle-Safety Committee) ein Prüfverfahren entwickelt. Es handelt sich dabei um ein Komponentenprüfverfahren, mit dem die Frontstruktur von Fahrzeugen, die bei einer Kollision mit einem Fußgänger hauptsächlich betroffen ist, geprüft wird. Es werden keine den gesamten Menschen repräsentierende Dummies verwendet, stattdessen werden Prüfkörper, die einzelne Körperteile simulieren, eingesetzt. Dieser EEVC Vorschlag wird geschildert. Darüber hinaus wird über Aktivitäten außerhalb des EEVC berichtet, sowie über den aktuellen Stand der Bemühungen der Europäischen Kommission in Bezug auf den Fußgängerschutz, die derzeit, auf Grundlage des Prüfvorschlages des EEVC, einen Vorschlag für eine Europäische Richtlinie erarbeitet.
The price of a new car increased almost every year for a long period. In recent years however, the budget available to most people for purchasing a car either did not grow or became even smaller. Therefore it was in the interest of some OEMs to offer economical car models in the so-called "8,000- Euro class". Here an important question arose regarding the safety of these vehicles. There is no question that the very high safety level of cars reached in Europe during the last decades should not be sacrificed as a consequence of smaller budgets. Customers with sense of responsibility have the right to be properly informed about the balance between safety and price so that they can make a deliberate decision when buying either a new or a used car. Against this background, the German magazine "AutoBILD" commissioned DEKRA to conduct fullscale frontal crash tests with a view to publishing the results. These tests have been carried out in accordance with the corresponding Euro NCAP crash test requirements and performance criteria. The tested vehicles were two new Logans produced by the manufacturer Dacia, two used cars of the type VW Golf IV (registration date 2000) and one new VW Fox. This paper describes the safety features of the vehicles and the results of the five crash tests to demonstrate state-of-the-art safety levels and what levels may be expected from vehicles in the "8,000- Euro class". Looking at real-world crashes it is of interest to think about future trends in a more detailed manner. Therefore it will be more and more necessary to supplement the federal statistics with more detailed in-depth information about the consequences of accidents and the safety performance of crashed vehicles.
The utilisation of secondary-safety systems to protect occupants has attained a very high level over the past decades. Further improvements are still possible, but increasingly minor progress is only to be had with a high degree of effort. Thus, a key aspect must be the impact to overall safety in an accident. If reliable information is available on an imminent crash, measures already taken in the pre-crash phase can result in a significantly great influence on the outcomes of the crash. With this background preventive measures are the key to a sustainable further reduction of the figures of crash victims on our roads. This paper aims to show a preventive approach that can contribute to lessening the consequences of a crash by creating an optimum interaction of measures in the fields of primary and secondary safety. To further enhance vehicle safety, driver assistant systems are already available that warn the driver of an imminent front-to-rear-end crash. The next step is to support him in his reactions or if he fails to react sufficiently, to even initiate an automatic braking when the crash becomes unavoidable. Automatic pre-crash braking can, in an ideal situation, fully prevent a crash or can significantly reduce the impact speed and thus the impact energy (and the severity of the accident). If a vehicle is being braked in the pre-crash phase, the occupants are already being pre-stressed by the deceleration. The information available about the imminent crash can be used to activate the belt tensioners and likewise other secondary safety systems in the vehicle right before the impact. The pre-crash deceleration also causes the front of the vehicle to dip. Conventional crash tests do not take this specific impact situation into consideration. This is why, for example, the influences of the pre-crash displacements of the occupants are not recorded in the test results. Furthermore, a reproducible representation of the benefit of the vehicle safety systems which prepare the occupants for the imminent impact is not possible. In order to demonstrate the functions of automated pre-crash braking and to investigate the differences during the impact as a consequence of the altered occupant positions as well as the initiation of force and deformations of the vehicle front, DEKRA teamed up with BMW to carry out a joint crash test with the latest BMW 5 series vehicle. It involved the vehicle braking automatically from a starting test speed of 64 km/h (corresponding to the impact speed set by Euro NCAP) down to 40 km/h. The test was still run by the intelligent drive system of the crash test facility. This required several modifications to be made to the test facility as well as to the vehicle. The paper will describe and discuss some relevant results of the crash test. In addition, the possible benefits of such systems will also be considered. The test supplemented the work of the vFSS working group (vFSS stands advanced Forward-looking Safety Systems).
Active safety systems are aimed at accident prevention, hence the knowledge required for their development is different from that required for passive safety systems aimed at injury prevention. Particularly, knowledge about accident causation is required. When looking at existing accident causation data, it is argued it fails to explain in sufficient detail how and why the accidents occur. Therefore, there is a need for detailed micro-level descriptions of accident causation mechanisms, and also of methodologies suitable for creating such descriptions. One study addressing these needs is the Swedish project FICA (Factors Influencing the Causation of Accidents and Incidents), where an accident investigation methodology suitable for active safety is developed, and in-depth accident investigations following this methodology are carried out on-scene in the area of Gothenburg by a multidisciplinary team. A preliminary aggregated analysis of different cases shows that the methodology developed is adequate for pointing out common contributing factors and devising principal countermeasures.
At the beginning of the year 2000 the European Commission set the goal to halve the number of road deaths till the year 2010. The main focus are passenger car and lorry traffic. A significant reduction of the accident data could be reached in these groups. The advancement of active vehicle safety systems is an important issue of the programme. The safety of the motorcycle traffic has been disregarded till now. Since 1991 the number of killed motorcycle riders per year has been constant. The number of killed passenger car occupants has been more than halved in the same period. This is why initiatives are caused for the increase of the motorcycle safety. A great safety potential is expected for the Antilock Brake System (ABS). ABS for motorcycles is considered from the economic view in this study. A cost-benefit analysis shall clarify whether the economic benefit of ABS for motorcycles is greater than the consumed resources. Moreover, a sensitivity analysis will determine the maximal justifiable consumption in resource for which ABS is worthwhile. After the sensitivity analysis is done a break-even analysis will determine the market price respectively the annual mileage from which on ABS is worthwhile on user level. For this the fair end consumer market price is calculated which the user is ready to pay. For the considered market prices the annual mileage is determined from which on ABS is worthwhile for the user. The considered time horizon for this analysis are the years 2015 and 2020. For each of these years the accident data is forecasted. At this, it is assumed that the frequency of having an accident per million registered motorcycles decreases based on the present trend. Thus, riding motorcycle gets safer. Hence, the accident data in the years 2015 and 2020 is lower than the accident data today. The cost-benefit analysis is done for each year for four scenarios. Two scenarios handle the market penetration. The first one is the trend scenario, the second one is the mandatory equipment from the year 2010 on. The other scenarios describe the effectiveness of ABS. The effectiveness rates are determined by a literature review. The only potential which can be considered due to the available data is the potential due to an avoiding of the downfall just before the real accident happens. According to this the number of accidents will decrease by 2.4 %. The number of fatalities will decrease by 12.1 %. The number of severe injuries decreases by 11.7 %. However, the number of slight injuries increases by 2.1 %. The mentioned effectiveness rates are valid for the scenarios with the high effectiveness. Even these figures underestimate the actual effectiveness because there are only considered the avoided accidents with downfall. The necessary consumption in resources depends on the produced volume. The more ABS systems are produced, the lower are the costs per system. This is due to realised effects of scale and effects out of learning curves. The system costs depend on the penetration rate. In the trend scenario the system costs for ABS are 120 Euro for the year 2015 respectively 105 Euro for the year 2020. In the mandatory scenario the system costs are 115 Euro for the year 2015 respectively 100 Euro for the year 2020. The benefit-cost ratios are all over the critical barrier of 1.0. Thus, ABS is worthwhile on economic level. In the scenarios with high effectiveness the benefit-cost ratios range between 4.6 and 4.9. Thus, the values are even above the barrier of 3.0. The result of the break-even analysis is that ABS is worthwhile on user level. The considered market prices are 400 Euro in 2015 and 300 Euro in 2020. They are clearly below the determined fair end consumer market prices. The fair end consumer price for the year 2015 is 701 Euro respectively 622 Euro for the year 2020. Thus, ABS is worthwhile for motorcycle riders with an annual mileage higher than 2,200 km (year 2015) respectively 1,900 km (year 2020). The annual mileage of a motorcycle rider is 3,900 km on average. Thus, ABS is worthwhile for most of the motorcycle riders. The mentioned results are valid for the high effectiveness scenarios.
Cost benefit analysis
(2014)
Although the number of road accident casualties in Europe is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities [EC 2012]. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car- safety performance in frontal impacts is to improve its compatibility for car-to-car impacts and for collisions against objects and HGVs. Compatibility consists of improving both a car- self and partner protection in a manner such that there is good interaction with the collision partner and the impact energy is absorbed in the car- frontal structures in a controlled way which results in a reduction of injuries. Over the last ten years much research has been performed which has found that there are four main factors related to a car- compatibility [Edwards 2003, Edwards 2007]. These are structural interaction potential, frontal force matching, compartment strength and the compartment deceleration pulse and related restraint system performance. The objective of the FIMCAR FP7 EC-project was to develop an assessment approach suitable for regulatory application to control a car- frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.
Because of actual developments and the continuous increase in the field of drive assistant systems, representative and detailed investigations of accident databases are necessary. This lecture describes the possibility to estimate the potential of primary and secondary safety measures by means of a computerized case by case analysis. Single primary or secondary safety measures as well as a combination of both are presented. The method is exemplarily shown for the primary safety measure "Brake Assist" in pedestrian accidents. Regarding accident prevention only the primary safety measure is determined.
The levels of continuous vehicle automation have become common knowledge. They facilitate overall understanding of the issue. Yet, continuous vehicle automation described therein does not cover "automated driving" as a whole: Functions intervening temporarily in accident-prone situations can obviously not be classified by means of continuous levels. Continuous automation describes the shift in workload from purely human driven vehicles to full automation. Duties of the driver are assigned to the machine as automation levels rise. Emergency braking, e.g., is obviously discontinuous and intensive automation. It cannot be classified under this regime. The resulting absence of visibility of these important functions cannot satisfy " especially in the light of effect they take on traffic safety. Therefore, in order to reach a full picture of vehicle automation, a comprehensive approach is proposed that can map out different characteristics as "Principle of Operation" at top level. On this basis informing and warning functions as well as functions intervening only temporarily in near-accident situations can be described. To reach a complete picture, levels for the discontinuous, temporarily intervening functions are proposed " meant to be the counterpart of the continuous levels already in place. This results in a detailed and independent classification for accident-prone situations. This finally provides for the visibility these important functions deserve.
In recent years the boundaries between active and passive safety blurred more and more. Passive safety in the traditional term includes all safety aspects to prevent occupants to be injured or at least injury severity should be reduced. Passive Safety starts with the collision (first vehicle contact) and ends with rescue (open vehicle doors). Within this phase the occupant has to be protected by the passenger compartment whereby no intrusion should occur. Active safety on the other side was developed to interact prior to the collision whereby the goal is to prevent accidents. The extensive interaction between active and passive safety led to the terminologies "Primary" and "Secondary" safety whereas the expression Integrated Safety Concept was generated. Within this study the most well documented single vehicle accidents with cars not equipped with ESP were identified from the PENDANT database and reconstructed. Additional cases were found in the database ZEDATU of TU Graz. In comparison each case was simulated with the assumption that the cars were equipped with ESP. The differences regarding accident avoidance or crash severity as well as reduction of injury risk were analysed.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
A series of drop tests and vehicle tests with the adult head impactor according to Regulation (EC) 631/2009 and drop tests with the phantom head impactor according to UN Regulation No. 43 have been carried out by the German Federal Highway Research Institute (BASt) on behalf of the German Federal Ministry of Transport, Building and Urban Development (BMVBS). Aim of the test series was to study the injury risk for vulnerable road users, especially pedestrians, in case of being impacted by a motor vehicle in a way described within the European Regulations (EC) 78/2009 and (EC) 631/2009. Furthermore, the applicability of the phantom head drop test described in UN Regulation No. 43 for plastic glazing should be investigated. In total, 30 drop tests, thereof 18 with the adult head impactor and 12 with the phantom head impactor, and 49 vehicle tests with the adult head impactor were carried out on panes of laminated safety glass (VSG), polycarbonate (PC) and laminated polycarbonate (L-PC). The influence of parameters such as the particular material properties, test point locations, fixations, ambient conditions (temperature and impact angle) was investigated in detail. In general, higher values of the Head Injury Criterion (HIC) were observed in tests on polycarbonate glazing. As the HIC is the current criterion for the assessment of head injury risk, polycarbonate glazing has to be seen as more injurious in terms of vulnerable road user protection. In addition, the significantly higher rebound of the head observed in tests with polycarbonate glazing is suspected to lead to higher neck loads and may also cause higher injury risks in secondary impacts of vulnerable road users. However, as in all tests with PC glazing no damage of the panes was observed, the risk of skin cut injuries may be expected to be reduced significantly. The performed test series give no indication for the test procedure prescribed in UN Regulation No. 43 as a methodology to approve glass windscreen not being feasible for polycarbonate glazing, as all PC panes tested fulfilled the UN R 43 requirements. The performance of the windscreen area will not be relevant for vehicle type approval according to the upcoming UN Regulation for pedestrian protection. However, it is recommended that pedestrian protection being considered for plastic windscreens to ensure at least the same level of protection as glass windscreens.
This paper uses the national accident statistics of Great Britain to evaluate the effectiveness of Electronic Stability Control Systems (ESC) to reduce crash involvement rates. The crash experience of 8,951 cars is analysed and compared to a closely matching set of non-ESC cars using case-control methods. This is one of the largest ESC samples analysed to date. Overall the cars with ESC are involved in 3% fewer crashes although the effectiveness is substantially higher under conditions of adverse road friction. ESC equipped cars are involved in 15% fewer fatal crashes although this reduction represents the combined effect of ESC and passive safety improvements.
Event data recorders (EDRs) are a valuable tool for in-depth investigation of traffic accidents. EDRs are installed on the airbag control module (ACM) to record vehicle and occupant information before, during, and after a crash event. This study evaluates EDR characteristics and aims at better understanding EDR performance for the improvement of accident reconstruction with more reliable and accurate information regarding accidents. The analysis is based on six crash tests with corresponding EDR datasets.
The presence and performance of Advanced Driver Assistance Systems (ADAS) has increased over last years. Systems available on the market address also conflicts with vulnerable road users (VRUs) such as pedestrians and cyclists. Within the European project PROSPECT (Horizon2020, funded by the EC) improved VRU ADAS systems are developed and tested. However, before determining systems" properties and starting testing, an up-to-date analysis of VRU crashes was needed in order to derive the most important Use Cases (detailed crash descriptions) the systems should address. Besides the identified Accident Scenarios (basic crash descriptions), this paper describes in short the method of deriving the Use Cases for car-to-cyclist crashes. Method Crashes involving one passenger car and one cyclist were investigated in several European crash databases looking for all injury severity levels (slight, severe and fatal). These data sources included European statistics from CARE, data on national level from Germany, Sweden and Hungary as well as detailed accident information from these three countries using GIDAS, the Volvo Cars Cyclist Accident database and Hungarian in-depth accident data, respectively. The most frequent accident scenarios were studied and Use Cases were derived considering the key aspects of these crash situations (e.g., view orientation of the cyclist and the car driver- manoeuvre intention) and thus, form an appropriate basis for the development of Test Scenarios. Results Latest information on car-to-cyclist crashes in Europe was compiled including details on the related crash configurations, driving directions, outcome in terms of injury severity, accident location, other environmental aspects and driver responsibilities. The majority of car-to-cyclist crashes occurred during daylight and in clear weather conditions. Car-to-cyclist crashes in which the vehicle was traveling straight and the cyclist is moving in line with the traffic were found to result in the greatest number of fatalities. Considering also slightly and seriously injured cyclists led to a different order of crash patterns according to the three considered European countries. Finally the paper introduced the Use Cases derived from the crash data analysis. A total of 29 Use Cases were derived considering the group of seriously or fatally injured cyclists and 35 Use Cases were derived considering the group of slightly, seriously or fatally injured cyclists. The highest ranked Use Case describes the collision between a car turning to the nearside and a cyclist riding on a bicycle lane against the usual driving direction. A unified European dataset on car-to-cyclist crash scenarios is not available as the data available in CARE is limited, hence national datasets had to be used for the study and further work will be required to extrapolate the results to a European level. Due to the large number of Use Cases, the paper shows only highest ranked ones.
Camera-monitor systems (CMS) can be used in motor vehicles to display the driver's rear view on a monitor mounted inside the vehicle. This also offers the possibility of replacing conventional exterior mirrors with suitable CMS and thereby implementing new design concepts with aerodynamic advantages. However, as exterior mirrors are safety-relevant vehicle parts for securing the driver's indirect rear view (requirements specified in UN Regulation No. 46), the question arises whether CMS can provide an equivalent substitute for mirrors. In the scope of this study, CMS and conventional exterior mirrors were compared and assessed in test drives and static tests under different external conditions. On the one hand, the examination of technical aspects, and on the other hand, issues pertaining to the design of the human-machine interaction, were the objects of the study. Two vehicles were available for the trials with passenger vehicles: A vehicle, manufactured in small series, which is already equipped with CMS as sole replacement for the exterior mirrors, as well as a compact class vehicle which had a CMS retrofitted by the car manufacturer in addition to conventionally used exterior mirrors. The latter could be covered exclusively for trips with CMS. A tractor unit with semitrailer was available for the truck trials. The driver's cabin was equipped with a CMS system developed by the vehicle manufacturer. In general, it was shown that it is possible to display the indirect rear view sufficiently for the driver, both for cars and trucks, using CMS which meet specific quality criteria. Depending on the design, it is even possible to receive more information about the rear space from a CMS than is possible with mirror systems. It was also shown that the change from mirrors to CMS requires a certain period of familiarisation. However, this period is relatively short and does not necessarily result in safety-critical situations.
Die vorliegende Studie untersucht die Auswirkung der Ausstattung von Motorrädern mit Anti-Blockier-System (ABS) auf die Fahrsicherheit von Motorrädern. Hierzu wurden Fahrversuche im realen Verkehr und auf abgesperrter Teststrecke durchgeführt. Erfahrene und wenig erfahrene Motorradfahrer absolvierten Testfahrten auf nasser und trockener Fahrbahn mit und ohne ABS-Aktivierung des Motorrades. Bei den Versuchsfahrten kam es zu einigen kritischen Fahrsituationen, bei denen die Versuchspersonen insbesondere zu Beginn des Bremsmanövers von ihrem "normalen" Bremsverhalten abwichen. Bei blockierendem Hinterrad wurde der Bremsdruck vorne und hinten reduziert, was zu einer deutlichen Bremswegverlängerung führte. Bei den Vollbremsungen unter idealen Bedingungen auf abgesperrter Strecke wurden von erfahrenen Fahrern ohne ABS kürzere Bremswege als mit ABS erreicht. Kurvenbremsungen mit ABS-Regelung wurden im mittleren Geschwindigkeits- und Schräglagebereich fahrstabil durchgeführt. Die Ergebnisse zeigen, dass selbst erfahrene Motorradfahrer Bremsweg in kritischen Situationen verschenken. Geeignete Antiblockiersysteme könnten Motorradfahrern die Angst vor Radblockaden nehmen. Dies dürfte einen erheblichen Beitrag zur Steigerung der aktiven Sicherheit leisten.
Brände in Reisebussen stellen ein sehr seltenes Ereignis dar. Das daraus resultierende Gefahrenpotenzial übersteigt aber das eines Pkws bei weitem, da von einer größeren Zahl betroffener Personen ausgegangen werden muss. Bauartbedingt ist mit erschwerten Bedingungen bei der Evakuierung von Bussen zu rechnen, insbesondere bei Sichtbehinderung durch Rauch in Verbindung mit Panikreaktionen der Fahrgäste. Derzeit gültige Richtlinien für Anforderungen an das Brandverhalten von Werkstoffen der Innenausstattung von Reisebussen geben reale Brände als prüftechnisches Szenario nur näherungsweise wieder. Dabei wird dem Einbauort der Materialien zu wenig Aufmerksamkeit gewidmet. Bezüglich Brandausbreitung (Übergang auf andere Baugruppen, brennendes Abtropfen) sind neue Kriterien erforderlich, welche die Zulassung des Werkstoffes beeinflussen können. Hinsichtlich der Toxizität der beim Verbrennen oder bei thermischer Belastung der Werkstoffe, insbesondere der Kunststoffe, entstehenden Rauchgase gibt es bis heute für den Reisebussektor nur unzureichende Vorschriften. In diesem Zusammenhang ist vor allem das gleichzeitige Brennen mehrerer unterschiedlicher Materialien im Innenraum von Reisebussen zu berücksichtigen. Zur Weiterentwicklung des bestehenden Regelwerks für die Zulassung von Reisebussen in Hinblick auf eine Optimierung der Brandvermeidung und der Brandeingrenzung mittels praxisnaher Prüfverfahren sollten im Rahmen dieses Projektes bestehende Regelwerke dargestellt und Verbesserungsmöglichkeiten aufgezeigt werden. Der vorliegende Abschlussberichts stellt die bisher gewonnenen Erkenntnisse dar. Besonderer Wert wurde dabei auf die Auswertung des realen Brandgeschehens von Reisebussen gelegt. Primär sind hierbei die Brandentstehung sowie die Ausbreitungswege analysiert worden. Ein weiterer Schwerpunkt ist die Darstellung von Brand-Detektionsverfahren. Forderungen aus dem Eisenbahnbereich in Bezug auf den Brandschutz in Personenzugwagen werden wiedergegeben, die Übertragbarkeit auf Reisebusse wird diskutiert. Die gewonnenen Erkenntnisse wurden in einem Lastenheft zusammengestellt, wobei die Orientierung an bestehenden Regelungen erfolgt. Neben der Prävention mittels Prüfverfahren wird besonderer Wert auf die Organisation sowie die Bereitstellung von Löschmitteln für effektive Erstmaßnahmen im Brandfall gelegt. Die Empfehlungen wurden im Rahmen eines Fachgesprächs mit Experten von Reisebusherstellern, mit Busunternehmern und mit Feuerwehrleuten diskutiert, Brandversuche wurden durchgeführt. Bei den vorgeschlagenen Prüfverfahren erfolgte eine Orientierung an den für das deutsche Eisenbahnwesen relevanten Normen. Zur Kostenreduktion werden für einige Bauteile alternative Prüfverfahren zugelassen. Mangels Reproduzierbarkeit, nur geringer Aussagekraft und unverhältnismäßig hoher Kosten wurden Full-Scale-Tests nicht in die Empfehlungen aufgenommen. Als Ergebnis steht die Forderung, dass alle Vorschläge im Falle einer Umsetzung europaweit gelten müssen. Die Brandfrüherkennung durch automatische Brandmeldeanlagen wurde für den Motorraum sowie in Teilen für den Innenraum befürwortet; dagegen werden automatische Löschanlagen aus wirtschaftlichen Gründen nicht gefordert werden. Beim mitgeführten Löschgerät sind Änderungen der bestehenden Regelung erforderlich, da sich diese auf abgelöste Normen beziehen, die Kombination von Pulver- und Schaumlöscher hat sich als Optimum herauskristallisiert. Besonders wichtig ist eine Information der Fahrgäste vor Fahrtantritt über die im Bus verwendeten Sicherheitseinrichtungen und deren Funktion. Bislang scheiterte die konsequente Umsetzung an der Vielzahl unterschiedlicher Funktionsprinzipien der Sicherheitseinrichtungen. Hier besteht Handlungsbedarf.
Die hier vorgestellten Forschungsprojekte hatten die Aufgabenstellung, - sinnvolle Obergrenzen für den biogenen Blend-Anteil im Kraftstoff aus ökonomisch-technischer Sicht aufzuzeigen sowie - technische Anforderungen an Pkw aus Altbestand und Neufahrzeugen für den Betrieb mit solchen Kraftstoff-Blends zu untersuchen, insbesondere in Hinblick auf Aspekte der Dauerhaltbarkeit. Auf Basis einer umfangreichen Literaturrecherche wurden zunächst sinnvolle Beimischungen ermittelt, die in 5 Fahrzeugen (3 Otto-Pkw, 2 Diesel-Pkw) auf einem Abgasrollenprüfstand getestet wurden. Anschließend wurden zwei Fahrzeuge einer Dauerlaufuntersuchung (ca. 80.000 km) unterzogen. Hierbei wurden u. a. Emissionsverhalten, Kraftstoffverbrauch und Motorleistung bewertet und Motorölproben entnommen. Am Ende der Dauerlaufuntersuchungen wurden bei beiden Fahrzeugen Motor und Kraftstoffsystem sorgfältig inspiziert. Aus fahrzeugtechnischer Sicht begrenzen bei Biodiesel vor allem die Ölverdünnung sowie der Anstieg der NOx-Emissionen den maximal möglichen Beimischungsanteil. Bei Bio-Alkohol sind insbesondere die Materialverträglichkeit und der Kraftstoffverbrauch limitierende Faktoren für erhöhte Beimischungen. Obwohl die betrachteten Euro-5-Fahrzeuge nicht für den Betrieb mit erhöhten Beimengungen an Biokraftstoffen ausgelegt waren, wurden die maßgeblichen Grenzwerte für die limitierten Emissionen im Verlauf der Untersuchungen nicht überschritten. Mit Ausnahme von NOx bei den Dieselfahrzeugen wurden darüber hinaus sogar die Euro-6-Grenzwerte unterschritten.
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
Regarding to the German road traffic licensing regulations it is mandatory to have a light system using a bicycle in public traffic. All attached components must be approved. The admission requires additional restrictions such as a dynamo as energy source with a nominal voltage of 6 V. Batteries are only allowed in addition to this. To adopt the German bicycle regulation to the state of art of an energy efficient lighting, additional power sources such as a battery respectively rechargeable batterie should be evaluated. The project will propose amendments for German Road Traffic Regulations and technical requirements.
Aufgrund des hohen Anteils von ca. 80 Prozent des Individualverkehrs am gesamten Personenverkehr, der abnehmenden Verkehrsräume und der zunehmenden Verkehrsdichte im innerstädtischen Bereich ist es erforderlich, geeignete Verkehrs- und Fahrzeugkonzepte zu entwickeln, um dieses Verkehrsaufkommen zu bewältigen. Die BMW AG hat vor diesem Hintergrund ein neuartiges Zweiradfahrzeug konzipiert. Auf diesem Fahrzeug sitzt der Fahrer aufrecht und angegurtet in einem speziellen Schutzraum, der aus Überrollbügeln gebildet wird. Zusätzlich verfügt das Zweirad im Frontbereich über eine Knautschzone. Da das Fahrzeug bezüglich der passiven Sicherheit über einen hohen Standard verfügt und die Akzeptanz am Markt davon abhängig ist, wird die Möglichkeit untersucht, den Fahrer dieses Fahrzeugs von der Helmtragepflicht zu befreien. Darüber hinaus werden allgemeine Aspekte der aktiven und passiven Sicherheit bewertet. Die Ergebnisse der Untersuchungen sollen es dem Bundesministerium für Verkehr ermöglichen, wissenschaftlich begründete Entscheidungen hinsichtlich der Befreiung von der Helmtragepflicht und den allgemeinen Zulassungsbedingungen zu treffen. Die Untersuchungen basieren auf Messergebnissen und Videoaufzeichnungen von Anprallversuchen, auf Ergebnissen von Computersimulationen, Daten aus Unfallerhebungen, Literaturstudien, Fachgesprächen und weiteren Analysen. Die Sicherheit des C1-Zweirades wurde jeweils für den Frontalanprall, den seitlichen Anprall und die Ausschleuderphase bewertet. Alle Versuchs- und Simulationsdaten ergaben Dummybelastungen, die zeigten, dass das C1-Fahrzeug im Frontalanprall erheblich sicherer ist als ein herkömmliches Zweirad. Auch beim seitlichen Anprall ergibt sich ein Sicherheitsvorteil gegenüber herkömmlichen Zweirädern. Die Ausschleuderphase bei einem Zweiradunfall ist sehr komplex. Soll der Fahrer des C1-Zweirades von der Helmtragepflicht befreit werden, ist sicherzustellen, dass sein Kopf zu keinem Zeitpunkt mit der Fahrbahn oder anderen Hindernissen in Kontakt kommt. Hierzu sind die Sicherheitsrahmenstruktur und das Gurtsystem entsprechend auszulegen. Um das Sicherheitspotential des Zweirades zu bewerten, wurden unter anderem Versuche nach ISO 13232 durchgeführt, in der Unfallkonstellationen zur Beurteilung des Schutzes von Zweiradaufsassen bei Unfällen empfohlen werden. Das Gutachten stellt fest, dass das C1-Zweirad die an die aktive und passive Sicherheit zu stellenden Anforderungen erfüllt. Darüber hinaus kann der Benutzer des Zweirades vorerst von der Helmtragepflicht befreit werden. Die Helmtragepflichtbefreiung ist an die Umsetzung von Sicherheitsanforderungen gekoppelt, die in einem Anforderungskatalog zusammengestellt wurden. In diesem Zusammenhang sind zwei neue Testverfahren entwickelt worden. Aus den Ergebnissen dieses Gutachtens wurden allgemeine Anforderungen für Zweiräder dieser Bauart definiert und eine Ausnahmeverordnung für die Straßenverkehrsordnung (Befreiung von der Helmtragepflicht) vorbereitet. Damit etwaige Probleme frühzeitig erkannt werden, sind nach Markteinführung Unfälle unter Beteiligung des C1-Zweirades sorgfältig zu beobachten und auszuwerten.
Für schwere Nutzfahrzeuge der Abgasstufe Euro 3 mit einem zulässigen Gesamtgewicht über 12 t liegen zur Zeit nur wenige belastbare Emissionsfaktoren (E-Faktoren) vor. Bislang sind nur vereinzelt entsprechende Motoren auf Prüfständen vermessen worden. Über das Emissionsverhalten solcher Antriebe im realen Fahrbetrieb liegen so gut wie keine Erkenntnisse vor. Ziele des Vorhabens waren: 1.) die Aufstockung der Emissionsfaktoren Datenbasis durch Vermessung von Fahrzeugen im Straßenbetrieb, 2.) der Vergleich von Realmessungen mit Werten aus dem Emissionsfaktoren-Handbuch und 3.) die Validierung moderner on-board-Messverfahren. Für die Messungen wurden drei schwere Sattelzugmaschinen mit Auflieger sowie ein Fahrzeug aus dem Verteilerverkehr ausgewählt. Es wurden Messfahrten mit voller und halber Beladung durchgeführt. Die verwendete on-board-Messtechnik erfasste hierbei zeitaufgelöst die gasförmigen Emissionen sowie den Abgasmassenstrom. Zusätzlich wurden Leistungs- und Geschwindigkeitsdaten erfasst. Für die Auswertung der Daten mussten die Fahrmuster, wie sie im Emissionsfaktoren-Handbuch beschrieben sind, aus den Fahrprofilen der Messfahrten isoliert werden. Für geeignete Fahrmuster wurden Emissionsfaktoren in g/km ermittelt und denen des Emissionsfaktoren-Handbuches gegenübergestellt. Zur Bewertung der benutzten on-board-Messtechnik wurden auf dem Motorprüfstand Vergleichsmessungen in den europäischen stationären und dynamischen Typprüfzyklen ESC und ETC durchgeführt. Bei diesen Vergleichen zeigte sich die Analysetechnik sehr gut geeignet für mobile Messungen. Abweichungen zu den Laborergebnissen traten im Wesentlichen durch Unterschiede in der Abgasmassenstrommessung auf. Der Vergleich der Handbuch-Emissionsfaktoren mit den in diesem Vorhaben gewonnenen Ergebnissen auf der Basis von Durchschnittsgeschwindigkeit und mittlerer positiver Leistung ergab bei den Sattelzügen keine gravierenden Unterschiede bei HC, NOx und CO2 für den Mittelwert über alle 3 Fahrzeuge. Bei CO wies ein Fahrzeug bei niedrigen Geschwindigkeiten deutlich höhere Emissionen und größere Varianzen auf, so dass dort die Kurve der Mittelwerte deutlich über der Trendkurve des Handbuchs liegt. Für eine leistungsspezifische Darstellung der Messwerte wurden in unterschiedlichen Leistungs- und Drehzahlfenstern quasistationäre Betriebsbedingungen gesucht und die Ergebnisse als gemittelte Emissionswerte dargestellt. Für ein Fahrzeug wurden exemplarisch die Prüfpunkte des ESC in diese Darstellung eingefügt. Bei Betrachtung der Betriebsweise auf der Straße und Vergleich mit der Wichtung der jeweiligen ESC-Prüfpunkte ist erkennbar, dass für dieses Fahrzeug die Wichtung des ESC nur sehr bedingt die Betriebsweise auf der Straße widerspiegelt. Abschließend kann festgestellt werden, dass, von Entwicklungsbedarf bei der Abgasmassen-strommessung abgesehen, Messtechnik zur Verfügung steht, um Realemissionen von Fahrzeugen im Straßenbetrieb für die Komponenten CO, HC, NOx und CO2 zu ermitteln. Die ermittelten Emissionsfaktoren sind geeignet, die Daten des Emissionsfaktoren-Handbuches zu validieren. Eine Erweiterung des Handbuches mit den ermittelten Ergebnissen ist aufgrund der sehr unterschiedlichen Datenstruktur nicht möglich. Dies ist aber auch nicht notwendig, da zwischen den Ergebnissen des Handbuches und den Ergebnissen der mobilen Straßenmessung eine gute Übereinstimmung besteht. Der Originalbericht enthält als Anhänge grafische Darstellungen der Geschwindigkeitsprofile der untersuchten Fahrten getrennt nach Automatik und Handschaltung bei unterschiedlichen Nutzlasten (Anhang A) sowie der Emissionsfaktoren der Fahrtabschnitte im Vergleich zum Handbuch (Anhang B). Auf die Wiedergabe dieser Anhänge wurde in der vorliegenden Veröffentlichung verzichtet. Sie liegen bei der Bundesanstalt für Straßenwesen vor und sind dort einsehbar. Verweise auf die Anhänge wurden zur Information des Lesers im Berichtstext beibehalten.
Bestimmung der vertikalen Richtcharakteristik der Schallabstrahlung vom Pkw, Transportern und Lkw
(2009)
Ziel der vorliegenden Untersuchungen war die messtechnische Bestimmung der spektralen horizontalen und vertikalen Richtcharakteristik sowie der Schallleistung von Fahrzeugen verschiedenen Typs während der Vorbeifahrt mit Hilfe eines Mikrofonarray-Messsystems. Diese Informationen sind wesentlich für die Schallausbreitung sowie die Wirksamkeit von Schallschutzmaßnahmen. Neben der gesamten Schallabstrahlung sollte der spektrale Gehalt des emittierten Schalls ermittelt werden. Grundlage des angewendeten Messverfahrens ist die Ausnutzung der steuerbaren Richtwirkungseigenschaft eines Mikrofonarrays. Durch Fokussierung des Mikrofonarrays auf das zu untersuchende Fahrzeug während der Vorbeifahrt können Störquellen ausgeblendet werden. Die ermittelten Schalldruckkartierungen ermöglichen die Berechnung der Richtcharakteristik und eine Abschätzung der Schallleistung des Fahrzeugs. Die Richtcharakteristik des eingesetzten Mikrofonarrays wurde im Hinblick auf die Lokalisation des vorbeifahrenden Fahrzeugs optimiert. Da für die Untersuchungen ausschließlich die Quelllokalisation in horizontaler beziehungsweise vertikaler Richtung notwendig ist, wurde ein Linienarray gewählt. Gegenüber einem zweidimensionalen Mikrofonarray erhöhen sich bei gleicher Mikrofonanzahl die örtliche Auflösung und die Nebenkeulenunterdrückung. Unter Einsatz des optimierten Linienarrays erfolgten Messungen im fließenden Verkehr bei kontrollierter Vorbeifahrt eines Pkw, eines Kleintransporters und eines Lkw mit ausgewählten Geschwindigkeiten. Die horizontale Richtcharakteristik wurde durch Lokalisation des vorbeifahrenden Fahrzeugs zu verschiedenen Zeitpunkten bestimmt. Durch wiederholte Vorbeifahrt bei gleicher Geschwindigkeit mit variierter Höhe des vertikal positionierten Mikrofonarrays konnte die mittlere vertikale Richtcharakteristik ermittelt werden. Für die Abschätzung der Schallleistung wurde das Hüllflächen-Verfahren an die näherungsweise Schallleistungsbestimmung bewegter Quellen mit Mikrofonarray angepasst.
Erfahrungen in Deutschland mit der Anwendung der EU-Empfehlung "Europäischer Grundsatzkatalog zur Fahrer-Fahrzeug-Schnittstelle für Informations- und Kommunikationssysteme" werden beschrieben und daraus Konsequenzen abgeleitet. Insgesamt ist die ergonomische Bewertung der Mensch-Maschine-Schnittstelle von Fahrerinformations- und -Kommunikationssystemen nicht als einmaliges Ereignis, sondern als immer wieder zu durchlaufender Vorgang anzusehen, da neben neuen wissenschaftlichen Erkenntnissen jeweils neu entwickelte Geräte und Systeme zu berücksichtigen sind, was eine Anpassung der Grundsätze beziehungsweise eine Öffnung der Grundsätze für technische Neuerungen mit hohem Sicherheitsstandard erfordern könnte. Demonstrationen neuartiger Bedienkonzepte, Systementwicklungen und Arbeitstechniken sowie die hierzu durchgeführten Nutzertests verdeutlichen, dass ergonomisch sehr vielversprechende Lösungen (wie zum Beispiel Schnittstellen, die Eingaben mittels Gestik gestatten) existieren, beziehungsweise sich in der Entwicklung befinden. Diese Lösungen zeigen, dass die Empfehlung in weiten Bereichen technologieabhängig, das heißt, mit Blick auf Neuentwicklungen, nicht erschöpfend ist. Die Weiterentwicklung der Grundsätze sowie die Bewertung der sicheren Gestaltung der Mensch-Maschine-Schnittstelle bedarf nicht nur einer europaweit, sondern weltweit abgestimmten Vorgehensweise.
The paper presents a methodology for the benefit estimation of several secondary safety systems for pedestrians, using the exceptional data depth of GIDAS. A total of 667 frontal pedestrian accidents up to 40kph and more than 500 AIS2+ injuries have been considered. In addition to the severity, affected body region, exact impact point on the vehicle, and the causing part of every injury, the related Euro NCAP test zone was determined. One results of the study is a detailed impact distribution for AIS2+ injuries across the vehicle front. It can be stated, how often a test zone or vehicle part is hit by pedestrians in frontal accidents and which role the ground impact plays. Basing on that, different secondary safety measures can be evaluated by an injury shift method concerning their real world effectiveness. As an example, measures concerning the Euro NCAP pedestrian rating tests have been evaluated. It was analysed which Euro NCAP test zones are the most effective ones. In addition, real test results have been evaluated. Using the presented methodology, other secondary safety like the active bonnet (pop-up bonnet) or a pedestrian airbag measures can be evaluated.
Accident data shows that the vast majority of pedestrian accidents involve a passenger car. A refined method for estimating the potential effectiveness of a technology designed to support the car driver in mitigating or avoiding pedestrian accidents is presented. The basis of the benefit prediction method consists of accident scenario information for pedestrian-passenger car accidents from GIDAS, including vehicle and pedestrian velocities. These real world pedestrian accidents were first reconstructed and the system effectiveness was determined by comparing injury outcome with and without the functionality enabled for each accident. The predictions from Volvo Cars" general Benefit Estimation Model are refined by including the actual system algorithm and sensing models for a relevant car in the simulation environment. The feasibility of the method is proven by a case study on a authentic technology; the Auto Brake functionality in Collision Warning with Full Auto Brake and Pedestrian Detection (CWAB-PD). Assuming the system is adopted by all vehicles, the Case Study indicates a 24% reduction in pedestrian fatalities for crashes where the pedestrians were struck by the front of a passenger car.
In the last years various new driver information and driver assistance systems made their way into modern vehicles and there are yet countless systems underway. However, expenses for both, the development and the construction of these systems are tremendous. Therefore the interest of evaluating systems keeps growing steadily, not only regarding the results of systems developed in the last years but also regarding system ideas. Only if at least a rough benefit estimation is given, the industry can decide which development should be supported. However, there is still a lack of transparency of possible and useful methods for these kinds of estimations. These were analyses and structured in this study.