91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
Volltext vorhanden
- nein (133) (entfernen)
Schlagworte
- Sicherheit (58)
- Safety (57)
- Bewertung (40)
- Evaluation (assessment) (40)
- Vehicle (39)
- Fahrzeug (38)
- Anfahrversuch (34)
- Impact test (veh) (31)
- Conference (28)
- Test method (28)
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
Die Autoren berichten über den Auftaktworkshop "Empfehlung der Europäischen Kommission über On-board-Informations- und -Kommunikationssysteme: Europäischer Grundsatzkatalog zur Mensch-Maschine-Schnittstelle", der am 7.9.2000 in der Bundesanstalt für Straßenwesen stattfand. Die zuständigen Stellen (wie zum Beispiel die Fahrzeug- und Zulieferindustrie) wurden dazu angehalten, die Empfehlungen zu beachten sowie der BASt über Erfahrungen zu berichten. Dazu wurde mit den Teilnehmern ein erster Gedankenaustausch geführt und das gemeinsame Vorgehen abgestimmt.
Erfahrungen in Deutschland mit der Anwendung der EU-Empfehlung "Europäischer Grundsatzkatalog zur Fahrer-Fahrzeug-Schnittstelle für Informations- und Kommunikationssysteme" werden beschrieben und daraus Konsequenzen abgeleitet. Insgesamt ist die ergonomische Bewertung der Mensch-Maschine-Schnittstelle von Fahrerinformations- und -Kommunikationssystemen nicht als einmaliges Ereignis, sondern als immer wieder zu durchlaufender Vorgang anzusehen, da neben neuen wissenschaftlichen Erkenntnissen jeweils neu entwickelte Geräte und Systeme zu berücksichtigen sind, was eine Anpassung der Grundsätze beziehungsweise eine Öffnung der Grundsätze für technische Neuerungen mit hohem Sicherheitsstandard erfordern könnte. Demonstrationen neuartiger Bedienkonzepte, Systementwicklungen und Arbeitstechniken sowie die hierzu durchgeführten Nutzertests verdeutlichen, dass ergonomisch sehr vielversprechende Lösungen (wie zum Beispiel Schnittstellen, die Eingaben mittels Gestik gestatten) existieren, beziehungsweise sich in der Entwicklung befinden. Diese Lösungen zeigen, dass die Empfehlung in weiten Bereichen technologieabhängig, das heißt, mit Blick auf Neuentwicklungen, nicht erschöpfend ist. Die Weiterentwicklung der Grundsätze sowie die Bewertung der sicheren Gestaltung der Mensch-Maschine-Schnittstelle bedarf nicht nur einer europaweit, sondern weltweit abgestimmten Vorgehensweise.
Es wird über das Ende 2002 abgeschlossene EU-Projekt ADVISORS berichtet. Ziel dieses Projektes, an dem sich 16 Organisationen aus 10 europäischen Ländern beteiligten, war es, die Entwicklung, Testung und Implementierung von Fahrerassistenzsystemen (FAS) zu unterstützen. Es wurde eine umfassende Methodik zur Bewertung von FAS entwickelt und auf dieser Basis wurden eine Reihe von Evaluationsstudien zu ausgewählten FAS durchgeführt. Des Weiteren wurden Implementierungsstrategien für bestimmte FAS entwickelt und mit Experten verschiedener Länder diskutiert.
Sowohl mit dem 3. Road Safety Action Programme der Europäischen Kommission als auch mit dem deutschen Verkehrssicherheitsprogramm werden die verkehrspolitischen Zielsetzungen zur Erhöhung der Verkehrssicherheit in Europa und Deutschland festgelegt. Hierbei muss die passive Fahrzeugsicherheit auch weiterhin eine bedeutende Rolle übernehmen. Es ist jedoch auch festzustellen, dass durch den zunehmenden Einsatz von Elektronik im Fahrzeug die klassischen Bereiche der aktiven und passiven Fahrzeugsicherheit mehr und mehr ineinander greifen. Der Fortschritt in der Elektronik ermöglicht eine Integration der Systeme der aktiven und passiven Sicherheit. Dadurch lässt sich die Fahrzeugsicherheit weiter steigern. Durch die Vernetzung der Systeme lassen sich sogar Kosten einsparen. Der europäische Regierungsausschuss EEVC (European Enhanced Vehicle-safety Committee), die Verbraucherschutzorganisation Euro NCAP (European New Car Assessment Programme) und die Europäische Kommission mit der eSafety Initiative haben diesen Trend erkannt und entsprechende Aktivitäten eingeleitet.
Die Gestaltung der Interaktion zwischen den elektronischen "Infotainment"-Systemen im Auto und dem Fahrer gewinnt zunehmend an Bedeutung für die Verkehrssicherheit. Dem positiven Nutzen, den die Systeme hinsichtlich Fahrerunterstützung und Fahrkomfort aufweisen, stehen möglicherweise negative Auswirkungen auf die Fahrsicherheit gegenüber, wenn Ablenkung und Überlastung des Fahrers auftreten. Diesem Problemfeld widmete sich das EU-Projekt "Communication Multimedia Unit Inside Car" (COMMUNICAR), das im Juni 2003 abgeschlossen wurde. Hauptziel des Projekts waren die Entwicklung und Evaluierung eines Systems, das den Fahrer bei der Bewältigung der eingehenden Informationen unterstützt und eine zentrale Bedienmöglichkeit aufweist. Das COMMUNICAR-System enthält folgende wesentliche Elemente: Verschiedene Funktionen zu Telematikdiensten, Unterhaltung und zur digitalen Darstellung der traditionellen Informationen; eine als Informationsmanager (IM) bezeichnete regelbasierte Filterlogik sowie eine multimediale integrierte Mensch-Maschine-Schnittstelle (MMS) zur zentralen Bedienung und Informationsausgabe. In der ersten Phase der Entwicklung wurden die Nutzeranforderungen analysiert, die Funktionen definiert und die Ein-/Ausgabemodalitäten festgelegt. In der zweiten Phase wurden virtuelle Prototypen zur Gestaltung der MMS erarbeitet und diese in den anschließenden Nutzertest im Labor bewertet und ausgewählt. Die dritte Phase diente der Systementwicklung, bei der es vor allem um die Filterlogik des IM ging. Das System wurde zunächst im Fahrsimulator, anschließend unter Feldbedingungen getestet. Die Ergebnisse, die in den wesentlichen Einzelheiten berichtet werden, zeigten insgesamt ein positives Bild sowohl hinsichtlich der subjektiven Akzeptanzbewertung als auch hinsichtlich des Fahrverhaltens.
Abschluss des deutsch-französischen Verbundprojekts "Inter-Vehicle Hazard Warning" (DEUFRAKO-IVWH)
(2004)
Im Rahmen der Deutsch-Französischen Kooperation im Verbundprojekt "Inter-Vehicle Hazard Warning" (DEUFRAKO-IVWH) wurde ein auf Fahrzeug-Fahrzeug-Kommunikation basierendes Warnsystem konzipiert und bewertet. Die im Rahmen des Projekts durchgeführten Arbeiten haben gezeigt, dass ein auf Fahrzeug-Fahrzeug-Kommunikation basierendes Warnsystem prinzipiell geeignet ist, einen Beitrag zur Erhöhung der Verkehrssicherheit zu leisten. Das Ausmaß der zu erwartenden positiven Effekte ist allerdings ganz wesentlich abhängig vom Ausstattungsgrad der Fahrzeugflotte mit einem solchen System.
Der Autor berichtet über das neu eingerichtete Expertennetzwerk HUMANIST, das sich mit Fragen der nutzerorientierten und sicherheitsgerechten Gestaltung von Fahrerassistenz- und Informationssystemen befasst. Ziel sind die Zusammenführung und Integration entsprechender Forschungsaktivitäten auf europäischer Ebene.
Das Projekt IMPROVER (Impact Assessment of Road Safety Measures for Vehicles and Road Equipment / Wirkungsanalyse und Bewertung von verschiedenen Verkehrssicherheitsmaßnahmen) wurde im Auftrag der Europäischen Kommission (Generaldirektion Energie und Verkehr) bearbeitet, um die folgenden Straßenverkehrssicherheitsaspekte zu untersuchen: den Einfluss der wachsenden Zahl von Sport Utility Vehicles (SUV) und Multi Purpose Vehicles (MPV) auf Verkehrssicherheit, Kraftstoffverbrauch und Emissionen; die Bewertung von Maßnahmen zur Verbesserung der Verkehrssicherheit von leichten Nutzfahrzeugen; die Auswirkungen des Tempomaten auf Verkehrssicherheit, Kraftstoffverbrauch und Emissionen; die Harmonisierung von Verkehrszeichen und Markierungen auf dem Transeuropäischen Straßennetz (TERN) unter Verkehrssicherheitsgesichtspunkten. Das Projekt wurde von der Bundesanstalt für Straßenwesen (BASt) zusammen mit 14 Partnerinstituten von November 2004 bis Mai 2006 bearbeitet. Entsprechend den Aufgaben wurde das Projekt in vier voneinander unabhängige Subprojekte eingeteilt. Der vorliegende Artikel gibt eine Übersicht über die in den jeweiligen Unterprojekten geleisteten Arbeiten, deren Ergebnisse und die daraus abgeleiteten Empfehlungen.
Die Autoren berichten über den Auftaktworkshop "Empfehlung der Europäischen Kommission über On-board-Informations- und -Kommunikationssysteme: Europäischer Grundsatzkatalog zur Mensch-Maschine-Schnittstelle", der am 7.9.2000 in der Bundesanstalt für Straßenwesen stattfand. Die zuständigen Stellen (wie zum Beispiel die Fahrzeug- und Zulieferindustrie) wurden dazu angehalten, die Empfehlungen zu beachten sowie der BASt über Erfahrungen zu berichten. Dazu wurde mit den Teilnehmern ein erster Gedankenaustausch geführt und das gemeinsame Vorgehen abgestimmt.
Die Reduzierung des Verkehrslärms ist eine große Herausforderung für alle Beteiligten. Das gilt umso mehr, als nach den Prognosen sich die Verkehrsleistung auf der Straße noch stark erhöhen wird. Viele Stellen in Deutschland, wie Industrie, Forschungseinrichtungen und Behörden haben sich der Problematik angenommen. Forschungsarbeiten wurden und werden durchgeführt oder sind in Vorbereitung. Über die nationalen Aktivitäten hinaus wird das Thema europaweit behandelt. In vier Beiträgen wird über die europäischen Forschungsprojekte SILVIA, ITARI, SILENCE und P2RN berichtet. Das Spektrum der Konzepte dieser Forschungsarbeiten ist sehr breit und erstreckt sich über praktische und theoretische Ansätze.
Mit der Forschungsarbeit sollte zur Klärung der Frage beigetragen werden, ob und gegebenenfalls in welcher Richtung und in welchem Ausmaß die Verwendung von Spikesreifen das Unfallgeschehen unmittelbar beeinflussen. Es wurden 3 Untersuchungsgebiete ausgewählt, von denen man annahm, dass die Spikesbenutzung unterschiedlich wäre: 1. Im norddeutschen Flachland: 3 Kreise im Münsterland, 2. Im hügeligen Bergland: 4 Kreise am Vogelsberg, 3. Im Voralpengebiet: 6 Kreise in Südbayern. Im Teil a) des Berichtes werden Verkehrserhebungen beschrieben, mit denen die Fahrleistungen spikesbereifter Fahrzeuge im Winter 1970/71 erfasst worden sind. Der Anteil spikesbereifter Fahrzeuge lag bei 33 % (Gebiet 1) bzw. 50 % (Gebiete 2 und 3). Der Anteil an den Fahrleistungen schwankte zwischen 17 % und 42 % (Einfluss der Witterungsbedingungen). Die Berechnung der Fahrleistungen der spikesbereiften Fahrzeuge wird dargestellt sowie der Anteil an der Gesamtfahrleistung, die Spikesbenutzung in Abhängigkeit von Fahrzeuggröße, Fahrtzweck, Sicherheitsgurt und Fahrweite untersucht. Im Teil b) wird die Unfallbeteiligung spikesbereifter Kfz untersucht. Insgesamt werden 6.107 Unfälle, davon 1.635 mit Personenschaden, erfasst. Fahrzeuge mit Spikesreifen waren gegenüber der Verkehrsbeteiligung unterrepräsentiert (um rd. 35 - 50 %). Die Unfallbeteiligung wird im Hinblick auf Unfallschwere, polizeilich festgestellte Unfallursachen und Abhängigkeit von der Tageszeit untersucht. Außerdem werden die Nebeneinflüsse Lebensalter, Alter der Fahrerlaubnis, Hubraum, Sicherheitsgurt analysiert. Im Anhang wird u.a. das Ergebnis einer Sondererhebung der Meinungen und Erfahrungen der Kfz-Sachverständigen zum Spikesproblem wiedergegeben.
Die Forschungsarbeit hatte das Ziel, das Griffigkeitsverhalten von Spikesreifen gegenüber Normalreifen zu klären. Dazu wurden mit einer repräsentativen Auswahl neuer und gebrauchter Reifen auf Versuchsstrecken in Bayern und Nordrhein-Westfalen mit dem Stuttgarter Reibungsmesser Gleitreibungsbeiwerte gemessen. Die Messungen wurden vorgenommen auf Decken unterschiedlicher Bauart, bei trockenem und nassem Fahrbahnzustand und bei unterschiedlichen Deckentemperaturen. Aus den Messwerten konnten für vorgegebene Ausgangsgeschwindigkeiten die Bremswege der unterschiedlichen Reifen auf den verschiedenen Deckenarten berechnet werden. Die Bremswegunterschiede (in %) ermöglichten eine Bewertung der untersuchten Reifen- und Deckenarten. Auswahl der Messstrecken sowie Messmethoden und -Durchführung werden beschrieben, die Messergebnisse ausführlich dargestellt und gedeutet. Aus einem Stichprobenumfang von mehr als 6.000 Einzelbremsungen lässt sich als wesentliches Untersuchungsergebnis ableiten, dass Radial-M+S-Reifen mit Spikes im Neuzustand gegenüber unbespiketen Reifen im Mittel über alle untersuchten Deckenarten bei trockener Fahrbahn einen um 15 - 20 %, bei nasser Fahrbahn um 17 - 26 % längeren Bremsweg aufweisen. Bei der Gussasphaltstrecke betrug der Bremswegunterschied zwischen Neuzustand und Ende des Gebrauchszustandes 40 %. Die größten ermittelten Einzelwerte der Bremswegunterschiede zwischen Radial-Sommerreifen und Radial-M+S-Reifen mit Spikes lagen in der Größenordnung von 40 - 50 %.
Es wird die Entwicklung einer Anlage zur Zählung von Fahrzeugachsen, die eine Straße überrollen, beschrieben. Diese Anlage gestattet, je nach Konfiguration, eine getrennte Erfassung von Pkw, Lkw und spikesbereiften Achsen. Eine Aufzeichnung der Zählergebnisse in vorwählbaren Zeitabständen (1 Stunde bis 1 Tag) auf einem Datenträger (z.B. 5-Kanal-Lochstreifen) kann vorgenommen werden. Mehrere Anlagen in verschiedenen Konfigurationen sind z.T. seit Jahren in Betrieb. Netz- und Batteriebetrieb sind möglich. Beispiele für Ergebnisse mit je nach Anlagentyp unterschiedlicher Aussagekraft werden gegeben.
Wegen der wachsenden Verbreitung von Fahrradanhängern zum Kindertransport und der möglichen Unfallgefährdung ist im vorliegenden Forschungsprojekt deren passive Sicherheit untersucht worden. Zudem wurde der Frage nachgegangen, ob der Transport von Kindern im Fahrradanhänger sicherer ist als mit dem Fahrrad mit Kindersitzen. In Absprache mit Herstellern und Vertreibern wurden verschiedene Untersuchungen durchgeführt. Es handelte sich um Anprallversuche (Anfahrversuche), Rollwagenversuche (Schlittenversuche) sowie Kopffreiheitsprüfungen und Fallversuche. Bei den Versuchen waren die Prüfobjekte mit einem oder zwei Dummies besetzt, die mit Messdatenaufnehmern ausgestattet waren. Verschiedene Messdaten, zum Beispiel Kopf- und Brustbeschleunigung, wurden erfasst und ausgewertet. Zusätzlich wurde das Kopfschutzkriterium (HPC) berechnet und bewertet. Entstandene Schäden an den Prüfobjekten wurden aufgenommen und durch Fotos dokumentiert. Die Versuchsabläufe selbst wurden mit Hochgeschwindigkeitskameras aus verschiedenen Positionen aufgezeichnet. Beim Anfahrversuch mit einem Pkw gegen ein Gespann aus Fahrrad und Anhänger waren direkte Anstöße der Anhängerinsassen an die Pkw-Front zu erkennen. Die Beschleunigungswerte waren dabei relativ hoch. Anstöße gegen Anhängerinnenteile waren bei fast allen Versuchen zu beobachten. Teilweise wurden Radaufhängungen und Radnaben beschädigt. Durch die Rollwagenversuche wurden konstruktive Schwächen bei den Sitzen und Rückhaltesystemen festgestellt. Nähte, Befestigungen und Verstellösen wurden zerstört. Es stellte sich heraus, dass die Qualität des Gurtsystems, die Steifigkeit des Anhängeraufbaus, die Sitzposition der Kinder und die vorhandene Kopffreiheit ausschlaggebend für das Verletzungsrisiko der Insassen sind. Bei den Versuchen mit Fahrradsitzen ergaben sich hohe Beschleunigungswerte durch den direkten Kontakt des Radfahrers mit der Fahrzeugfront und/oder der Fahrbahn. Das Gewicht des Radfahrers, des Fahrrades und auch Fahrradteile bergen ein erhöhtes Verletzungsrisiko für das Kind. Zusätzlich besteht die Gefahr überfahren zu werden, wenn das Kind nach dem Sturz des Fahrrades ungeschützt auf der Fahrbahn liegt. Ein direkter Vergleich der beiden Transportmöglichkeiten war aufgrund der geringen Daten der Versuche mit Fahrradkindersitzen nur bedingt möglich. Tendenziell ist der Transport der Kinder im Fahrradanhänger als weniger gefährlich zu bewerten. Es werden die Vor- und Nachteile dargestellt. Zur Bewertung der Sicherheit von Fahrradanhängern wurden die folgenden Prüfmethoden erarbeitet: - Pendelschlagprüfung für die gesamte Chassisstruktur; - Kopffreiheitsprüfung; - Belastungsprüfung der Aufbaustruktur; - Festigkeitsprüfung der Gurtsysteme. Die Prüfungen sind so aufgebaut, dass sie mit einfachen Mitteln durchzuführen sind. Es sollte somit jedem Anhängerhersteller möglich sein, die passive Sicherheit seiner Produkte umfassend zu untersuchen. Die Prüfverfahren für die Sicherheitsbewertung sollen in eine DIN-Norm und in das Merkblatt für Fahrradanhänger einfließen. Der Original-Forschungsbericht enthält einen umfangreichen Fotoband zu den Einzelheiten der Versuche und Versuchsaufbauten sowie zu den Beschädigungen der Prüfobjekte und kann bei der BASt eingesehen werden.
Die vorliegende Studie untersucht die Auswirkung der Ausstattung von Motorrädern mit Anti-Blockier-System (ABS) auf die Fahrsicherheit von Motorrädern. Hierzu wurden Fahrversuche im realen Verkehr und auf abgesperrter Teststrecke durchgeführt. Erfahrene und wenig erfahrene Motorradfahrer absolvierten Testfahrten auf nasser und trockener Fahrbahn mit und ohne ABS-Aktivierung des Motorrades. Bei den Versuchsfahrten kam es zu einigen kritischen Fahrsituationen, bei denen die Versuchspersonen insbesondere zu Beginn des Bremsmanövers von ihrem "normalen" Bremsverhalten abwichen. Bei blockierendem Hinterrad wurde der Bremsdruck vorne und hinten reduziert, was zu einer deutlichen Bremswegverlängerung führte. Bei den Vollbremsungen unter idealen Bedingungen auf abgesperrter Strecke wurden von erfahrenen Fahrern ohne ABS kürzere Bremswege als mit ABS erreicht. Kurvenbremsungen mit ABS-Regelung wurden im mittleren Geschwindigkeits- und Schräglagebereich fahrstabil durchgeführt. Die Ergebnisse zeigen, dass selbst erfahrene Motorradfahrer Bremsweg in kritischen Situationen verschenken. Geeignete Antiblockiersysteme könnten Motorradfahrern die Angst vor Radblockaden nehmen. Dies dürfte einen erheblichen Beitrag zur Steigerung der aktiven Sicherheit leisten.
Die Schwingungsdämpfer von Pkw werden in Deutschland bei der regelmäßigen technischen Überwachung im Rahmen der Hauptuntersuchung nach Paragraph 29 StVZO überprüft. In eingebautem Zustand werden sie dabei im wesentlichen nur einer Sichtkontrolle unterzogen, bei der die Dichtigkeit der Dämpfer und ihre äußerliche Unversehrtheit beurteilt werden. Ziel der Untersuchung war die Klärung der Frage, ob die Notwendigkeit einer aussagekräftigeren Kontrolle der Schwingungsdämpfer bei der regelmäßigen technischen Überwachung von Kraftfahrzeugen besteht, da die objektive Messung der Dämpferleistung problematisch ist und der Nutzen einer solchen Maßnahme bisher nicht quantifiziert werden kann. Objektive Prüfergebnisse an Schwingungsdämpfern sind jedoch nur in ausgebautem Zustand zu erhalten. Durch die Untersuchung sollte über eine "Ist-Zustands-Prüfung" von im Verkehr befindlichen Pkw und eine darauf aufbauende Hochrechnung der Anteil der Fahrzeuge, die mit defekten Dämpfern fahren, festgestellt werden. Die Auswertung der Reihenuntersuchung ergab, dass von 5.749 untersuchten Pkw 450 Pkw eine Fahrwerksbeurteilung erhielten, nach der an mindestens einem Rad der prüfstandspezifische Grenzwert nicht eingehalten wurde, was in der Regel auf einen defekten Dämpfer zurückzuführen ist. Dies entspricht hochgerechnet einem Anteil von 7,8 Prozent der zugelassenen Pkw. Folgt man den durch die Reihenuntersuchung ermittelten Ergebnissen und den bisher diskutierten Grenzwerten von 50 Prozent für die Restwirkung der Dämpfer, so würde die Einführung einer obligatorischen Dämpferprüfung zu erheblichen Kosten führen, deren Nutzen jedoch aufgrund fehlender Angaben derzeit nicht festgestellt werden kann. In Anbetracht der Unsicherheiten bezüglich des Einflusses defekter Schwingungsdämpfer auf das Unfallgeschehen und der ermittelten Defektrate konnte die Einführung einer obligatorischen Prüfung auf einem Prüfstand im Rahmen der regelmäßigen Hauptuntersuchung nicht abschließend bewertet werden.
In der Europäischen Gemeinschaft werden derzeit jährlich ca. 50.000 Menschen bei Verkehrsunfällen getötet, ca. 10.000 davon als Fußgänger. Von den 10.600 (1992) in der Bundesrepublik Deutschland bei Straßenverkehrsunfällen Getöteten waren 1.800 Fußgänger (etwa 17 Prozent). Problemgruppen bei Fußgängerunfällen bilden die Kinder wegen ihrer hohen Unfallhäufigkeit und alte Personen wegen ihrer hohen Unfallschwere. Kopfverletzungen sind die häufigste Todesursache bei Fußgängerunfällen. Eine Verringerung der Unfallschwere kann - außer durch Verminderung von Fahr- beziehungsweise Aufprallgeschwindigkeiten der Fahrzeuge - nur durch konstruktive Eingriffe an der vorderen Fahrzeugaußenkontur oder dem Unterbau von Pkw erfolgen. Dazu ist es notwendig, einheitliche Prüfverfahren für die Beurteilung der "Fahrzeugaggressivität" gegenüber Fußgängern bereitzustellen. Die Ableitung eines Prüfvorschlages zur Simulation des Kopfaufpralls auf Fronthauben von Pkw beim Fußgängerunfall, unterteilt in Kopfaufpralltests für Erwachsene und Kinder, ist Gegenstand dieser Arbeit. Es werden, ausgehend von einer Analyse der Unfallstatistik, der Entstehungsmechanismus von Kopfverletzungen erklärt, die für ein Prüfverfahren notwendigen Eingangsparameter (Masse, Geschwindigkeit, Aufprallstellen am Fahrzeug etc.) abgeleitet und die Ergebnisse der gewählten Prüfkörpertestmethode mit Ergebnissen von Leichenversuchen verglichen. Eine Kosten-/Nutzen-Betrachtung am Schluss der Arbeit zeigt, dass sich bei nur geringen Kosten ein volkswirtschaftlicher Nutzen durch eine allgemeine Anwendung des Prüfverfahrens mit ca. 270 Millionen DM allein in der Bundesrepublik Deutschland pro Jahr erzielen ließe.
In Form einer Pilotstudie wurden eine Literaturrecherche, eine Befragung von Experten der Automobilindustrie und theoretische Untersuchungen zur Frage der Head-Up-Display-Technik (HUD) im Kraftfahrzeug durchgeführt. Auf der Suche nach neuen, die Sicherheit des Kraftfahrzeugverkehrs fördernden Anzeigen findet das HUD zunehmend Interesse. Das Prinzip des HUD im Kraftfahrzeug besteht darin, dass die Informationen des Displays über den in die Windschutzscheibe integrierten Combiner in die Verkehrsszene als virtuelles Bild eingeblendet werden. In Europa wurden von Automobil- und Zulieferfirmen ca. ein Dutzend HUD-Systeme als Experimentalsysteme entwickelt. In den europäischen Forschungsprogrammen PROMETHEUS und DRIVE wird das HUD als eine von mehreren neuen Anzeigetechniken untersucht. In den USA und Japan befinden sich HUD-Systeme in Serienfahrzeugen bereits seit einigen Jahren auf dem Markt. Informationen auf einem HUD im Kraftfahrzeug werden schneller und sicherer abgelesen, als auf der konventionellen Instrumententafel. Insbesondere die physiologischen Anteile des Wahrnehmungsvorganges, das heißt die Augenbewegung, das Akkommodieren und das Adaptieren, erfolgen mit einem HUD schneller. Allerdings kann die Verquickung der Verkehrsszene mit bordeigenen Informationen zu verändertem Fahrverhalten und zu anderen Beobachtungsstrategien der Kraftfahrer führen. Die HUD-Technik ist zwar relativ fortgeschritten, jedoch liegen nur wenige fundierte experimentelle Ergebnisse vor. Es wurde daher eine Untersuchungsreihe mit Labor-, Simulator- und Feldexperimenten entworfen, die offene Fragen zu Nutzen, Informationsinhalten und Gestaltung von HUD-Anzeigen beantworten sollen. Gesetzliche Vorschriften der StVZO und die sie tangierenden EG-Richtlinien beziehungsweise ECE-Regelungen legen die Mindestanforderungen an die Sicht aus Kraftfahrzeugen fest, und es bestehen Vorgaben sowohl für die mögliche Position der HUD-Anzeigen, als auch für die Transmission und für die Farberkennung der Verkehrsobjekte.
Künftig sollen in Kfz-Scheinwerfern anstelle von Glühlampen auch Gasentladungslampen eingesetzt werden können. Hierbei handelt es sich um Hochdruckentladungslampen, die sich von bisher eingesetzten Halogen-Glühlampen durch die spektrale Verteilung ihres Lichtes, eine höhere Leuchtdichte und einen größeren Lichtstrom - bei geringerer elektrischer Aufnahmeleistung - unterscheiden. Derzeit werden Lampen unter der Bezeichnung D 1 in ein deutsches Fahrzeug der gehobenen Klasse eingebaut. Im Rahmen einer Vorstudie innerhalb des Projektes wurden die folgenden Punkte untersucht: - Integrierbarkeit der Lampe und des Scheinwerfers in bestehende Regelungen; - lichttechnische Eigenschaften der Gasentladungssysteme wie Zünd- und Anlaufverhalten in unterschiedlichen Betriebszuständen; - Farbwiedergabe retroreflektierender Verkehrszeichen und Signaleinrichtungen; - Leuchtdichtekontraste bei retroreflektierenden Materialien und Rückstrahlern; - Sicherheitsaspekte; - Blendung des Gegen- und des vorausfahrenden Verkehr. In der anschließenden Hauptstudie wurden Vorwärtsreflexion an Fahrbahnoberflächen zur Bestimmung der indirekten Blendung im trockenen und nassen Zustand; - spektrale Reflexion von Fahrbahndecken; - Streuleuchtdichten vor dem Fahrzeug bei Schlechtwettersituationen; - Blendungsunterschiede zwischen konventionellen und Gasentladungs-Systemen; - Gradient der Hell-Dunkel-Grenze untersucht. Bei der Untersuchung der Vorwärtsreflexion zeigte sich, dass sich bei nassen Fahrbahnoberflächen das Maximum der Reflexion in Fahrtrichtung verschiebt. In Schlechtwettersituationen wurde durch den größeren Lichtstrom ein Anstieg der Streuleuchtdichte gemessen. Aus diesem Grunde scheint eine Begrenzung der Vorfeldbeleuchtungsstärke sinnvoll. Aufgrund der Fahrzeugdynamik ergeben sich verschiedene Gradienten der Hell-Dunkel-Grenzen. Sie sind abhängig vom Fahrzeugtyp sowie von der Ausstattung der Fahrzeuge mit Niveauregulierung und automatischer Leuchtweitenregelung. Es ergab sich bei Verwendung von Gasentladungssystemen eine Erhöhung der Blendung. Die Blendbeleuchtungsstärken lagen dabei höher als bei vergleichbaren Halogensystemen. Ebenso wird durch die Vorwärtsreflexion auf der Fahrbahnoberfläche eine erhöhte Blendbeleuchtungsstärke bewirkt. Es zeigte sich, dass insbesondere zur Ermittlung der Beeinflussung älterer Verkehrsteilnehmer durch Gasentladungslampen weitere Untersuchungen erforderlich sind.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
The development of tyre- and truck-manufacturers leads to the direction to introduce wide base single tyres (size 495/45R22,5) instead of twin tyres on the driving axle of trucks, tractors and busses. To study the driving behaviour and safety of various trucks and units with different tyre combinations and loading conditions was the aim of the study. A computer-aided simulation was used for this investigation. Drive tests with a 40 t unit with prototype single tyres on the drive axle were carried out to verify the simulation. Alterations in driving behaviour and driving safety are mainly dependent on the tyre cornering stiffness. The prototype wide single tyres had a higher lateral stiffness which leads to a higher degree of under-steering (safer driving behaviour). The altered spring base on the drive axle had no influence on the side- tilt stability of vehicle combinations but the solo truck profited from the higher rear axle roll stiffness (less danger for roll-over accidents). As far as the driving safety is concerned nothing speaks against wide base tyres on the drive axle. The simulation of a tyre defect in a bend (assuming 40% of the max. transferable side force for the flat tyre) showed no increased danger using wide single tyres. Later driving tests showed however the need of tyre run flat possibilities to avoid jack-knifing of road trains. Also tyre pressure monitoring systems and electronic stability programs for the trucks are advised.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
Topics of this report are: Securing mobility and making mobility sustainable - Strategies for road safety: Safe behavior, Safe vehicles, Safe infrastructure, Telematics, International vehicle-engineering measures " Accident statistics " Accident research " Passive vehicle safety " Active vehicle safety " Driver assistance systems " Environmental protection through vehicle engineering.
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
The GRSP informal group on child restraint systems (CRS) finalised phase 1 of a new regulation for the homologation of CRS . This regulation is the subject of several discussions concerning the safety benefits and the advantages and disadvantages that certain specific points may bring. However, these discussions are sometimes not based on scientific facts and do not consider the whole package but only single items. Based on the experience of the CASPER partners in the fields of human behaviour, accident analysis, test procedures and biomechanics in the area of child safety, a consideration of the safety benefits of phase 1 of the new regulation and recommendations for phase 2 will be given.
The objective was to develop and validate a crash trolley (reference vehicle) equipped with a compartment and a full restraint system for driver and front seat passenger which can be used in full scale crash testing. Furthermore, the crash trolley should have a suspension to show rotation and nick effects similar to real vehicles. Within the development phase the reference vehicle was build based on a European family car. Special attention was needed to provide appropriate strength to the trolley and its suspension. The reference vehicle is equipped with a restraint system consisting of airbags, pedals, seats, dashboard, and windscreen. On the front of the vehicle different crash barriers can be installed to provide miscellaneous deceleration pulses. For the validation phase a series of low and high speed crash tests with HIII dummies were conducted and compared with full scale tests. For the comparison deceleration pulse, dummy numbers and vehicle movement were analyzed. Validation tests with velocities up to 60 km/h showed promising results. The compartment and the suspension systems stayed stable. Rotation effects were comparable with full scale car crash tests. The airbags and seat belt system worked reasonable. The acceleration pulse compared to an Euro NCAP test had a similar characteristic but was in general slightly lower. After the successful validation the reference vehicle is already in use in different studies in the field of vehicle safety research at BASt.
Topics of the status report are: Road accidents in Germany " Socio-economic costs due to road traffic accidents in Germany " Vehicle population and road performance " Electromobility " Alternative power train technologies: market penetration and consequences. The following research subjects are presented: Safety of electric vehicles " Driving dynamics of electric propelled vehicles " New requirements for the periodic technical inspection of electric and hybrid vehicles " Forward looking safety systems " Periodic roadworthiness tests " Cooperative systems: integration of existing systems " Safety related traffic information " Urban space: User oriented assistance systems and network management " Automated driving " Study on camera-monitor-systems " Freight transport " BioRID TEG, dummy harmonization " Frontal impact and compatibility " Child safety " FlexPLI " GIDAS: a blueprint for worldwide in-depth road accident investigations " Druid: Driving under the influence of drugs, alcohol and medicines " Smoke and toxicity in bus fires.
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of synthetic and plastic materials as a material for the interior equipment of buses and coaches because of their ood mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years - also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, the production of smoke, the smoke development and propagation and its toxicity for the people as well as the testing methods and limit values are of interest. For those reasons research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behavior of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and on-board extinguishing equipment were elaborated. At the other hand research is carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. The paper describes which effective and economically reasonable fire safety requirements for interiors of buses would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses.
Since integrated safety systems combine active and passive safety elements in one safety system, it is necessary to define new procedures to evaluate vehicle safety from the overall system point of view. The main goal of the ASSESS project is to develop harmonized and standardized assessment procedures for collision mitigation and avoidance systems. Methods and Data Sources: In ASSESS, procedures are developed for: driver behaviour evaluation, pre-crash system performance evaluation, crash performance evaluation, socio-economic assessment. This paper will concentrate on the activities related to the crash evaluation. The objective is to perform simulations, sled tests and crash tests in order tounderstand the influence of the activation of the pre-crash systems on the occupants" injuries during the crash phase. When a traffic accident is unavoidable, pre-crash systems work on various safety devices in order to improve the vehicle occupants" protection. Braking assistance and adaptive restraint systems are the main pre-crash systems whose effect on the occupants" protection will be described in this paper. Results: The results will be a description of the effect of the activation of the pre-crash systems on the crash phase. Additionally, a set of recommendations for future methodology developments will be delivered. Furthermore, a first approach to the study of the effect of the pre-crash systems activation on the occupants" protection when the impact is unavoidable will be presented. This effect will be quantified using the biomechanical values obtained from the simulation and testing activities and their related injury risks. Simulation and testing activities will consider the following scenarios: - No activation of any pre-crash system, - Activation of one or a combination of several pre-crash systems. In this way, differences in the results obtained from different scenarios will show the effect of each pre-crash system separately during the crash phase. Discussion and Limitations: The set of activities developed in this research project is limited by the fact that with the given resources only a limited number of vehicle models could be investigated. In addition, there are also limitations related to the injury risk curves and the passive safety tools currently on the market. Conclusion and Relevance to session submitted: The paper will present a complete analysis of the effect of pre-crash systems during the crash phase when the impact is unavoidable. Details, limitations and first application experience based on a few examples will be discussed. Currently, there is not any regulation, assessment program, or other similar official procedure able to assess pre-crash systems during the crash phase. This project comprises phases of traffic accidents which have been historically analysed separately, and aims to evaluate them taking into account their interrelationship. ASSESS is one of the first European projects which deals in depth with the concept of integrated safety, defining methodologies to analyse vehicle safety from a global point of view.
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
Thoracic injuries are one of the main causes of fatally and severely injured casualties in car crashes. Advances in restraint system technology and airbags may be needed to address this problem; however, the crash test dummies available today for studying these injuries have limitations that prevent them from being able to demonstrate the benefits of such innovations. THORAX-FP7 was a collaborative medium scale project under the European Seventh Framework. It focused on the mitigation and prevention of thoracic injuries through an improved understanding of the thoracic injury mechanisms and the implementation of this understanding in an updated design for the thorax-shoulder complex of the THOR dummy. The updated dummy should enable the design and evaluation of advanced restraint systems for a wide variety (gender, age and size) of car occupants. The hardware development involved five steps: 1) Identification of the dominant thoracic injury types from field data, 2) Specification of biomechanical requirements, 3) Identification of injury parameters and necessary instrumentation, 4) Dummy hardware development and 5) Evaluation of the demonstrator dummy. The activities resulted in the definition of new biofidelity and instrumentation requirements for an updated thorax-shoulder complex. Prototype versions were realised and implemented in three THOR dummies for biomechanical evaluation testing. This paper documents the hardware developments and biomechanical evaluation testing carried out.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Topics of this report are: Road accidents in Germany - Socio-economic costs due to road traffic accidents - Vehicle population and road performance " Automotive IT " Electromobility. The following research subjects are presented: Safety of electric vehicles - Forward looking safety systems - Cooperative systems - Safety related traffic information - Freight transport: Action plan freight transport and trial with longer trucks - Lane departure warning systems and Advanced emergency braking systems (AEBS) for heavy duty vehicles - Dummy harmonization " Compatibility - Child safety - Virtual testing - Driving under the influence of drugs, alcohol and medicines - Fire safety of buses - Milled shoulder rumble strips - Conspicuity of powered-two-wheelers - Automatically dipped high beam and rear view mirrors.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.