91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (36)
- Buch (Monographie) (30)
- Arbeitspapier (10)
- Wissenschaftlicher Artikel (9)
- Teil eines Buches (Kapitel) (2)
- Bericht (1)
Schlagworte
- Vehicle (88) (entfernen)
Die Autoren berichten über den Auftaktworkshop "Empfehlung der Europäischen Kommission über On-board-Informations- und -Kommunikationssysteme: Europäischer Grundsatzkatalog zur Mensch-Maschine-Schnittstelle", der am 7.9.2000 in der Bundesanstalt für Straßenwesen stattfand. Die zuständigen Stellen (wie zum Beispiel die Fahrzeug- und Zulieferindustrie) wurden dazu angehalten, die Empfehlungen zu beachten sowie der BASt über Erfahrungen zu berichten. Dazu wurde mit den Teilnehmern ein erster Gedankenaustausch geführt und das gemeinsame Vorgehen abgestimmt.
Die Reduzierung des Verkehrslärms ist eine große Herausforderung für alle Beteiligten. Das gilt umso mehr, als nach den Prognosen sich die Verkehrsleistung auf der Straße noch stark erhöhen wird. Viele Stellen in Deutschland, wie Industrie, Forschungseinrichtungen und Behörden haben sich der Problematik angenommen. Forschungsarbeiten wurden und werden durchgeführt oder sind in Vorbereitung. Über die nationalen Aktivitäten hinaus wird das Thema europaweit behandelt. In vier Beiträgen wird über die europäischen Forschungsprojekte SILVIA, ITARI, SILENCE und P2RN berichtet. Das Spektrum der Konzepte dieser Forschungsarbeiten ist sehr breit und erstreckt sich über praktische und theoretische Ansätze.
Mit der Forschungsarbeit sollte zur Klärung der Frage beigetragen werden, ob und gegebenenfalls in welcher Richtung und in welchem Ausmaß die Verwendung von Spikesreifen das Unfallgeschehen unmittelbar beeinflussen. Es wurden 3 Untersuchungsgebiete ausgewählt, von denen man annahm, dass die Spikesbenutzung unterschiedlich wäre: 1. Im norddeutschen Flachland: 3 Kreise im Münsterland, 2. Im hügeligen Bergland: 4 Kreise am Vogelsberg, 3. Im Voralpengebiet: 6 Kreise in Südbayern. Im Teil a) des Berichtes werden Verkehrserhebungen beschrieben, mit denen die Fahrleistungen spikesbereifter Fahrzeuge im Winter 1970/71 erfasst worden sind. Der Anteil spikesbereifter Fahrzeuge lag bei 33 % (Gebiet 1) bzw. 50 % (Gebiete 2 und 3). Der Anteil an den Fahrleistungen schwankte zwischen 17 % und 42 % (Einfluss der Witterungsbedingungen). Die Berechnung der Fahrleistungen der spikesbereiften Fahrzeuge wird dargestellt sowie der Anteil an der Gesamtfahrleistung, die Spikesbenutzung in Abhängigkeit von Fahrzeuggröße, Fahrtzweck, Sicherheitsgurt und Fahrweite untersucht. Im Teil b) wird die Unfallbeteiligung spikesbereifter Kfz untersucht. Insgesamt werden 6.107 Unfälle, davon 1.635 mit Personenschaden, erfasst. Fahrzeuge mit Spikesreifen waren gegenüber der Verkehrsbeteiligung unterrepräsentiert (um rd. 35 - 50 %). Die Unfallbeteiligung wird im Hinblick auf Unfallschwere, polizeilich festgestellte Unfallursachen und Abhängigkeit von der Tageszeit untersucht. Außerdem werden die Nebeneinflüsse Lebensalter, Alter der Fahrerlaubnis, Hubraum, Sicherheitsgurt analysiert. Im Anhang wird u.a. das Ergebnis einer Sondererhebung der Meinungen und Erfahrungen der Kfz-Sachverständigen zum Spikesproblem wiedergegeben.
Optimierung des rückwärtigen Signalbildes zur Reduzierung von Auffahrunfällen bei Gefahrenbremsung
(2002)
Das derzeitige Bremssignalbild übermittelt dem nachfolgenden Verkehr nur dass gebremst wird, die Fahrer erhalten jedoch keine Information über die Stärke des Bremsmanövers. Im vorliegenden Bericht wird im Rahmen einer Literaturstudie untersucht, wie das rückwärtige Signalbild optimiert werden könnte, um vor allem Gefahrenbremsungen gesondert darzustellen. Einige praktikable Lösungsvorschläge, die bereits fertig entwickelt sind, werden vorgestellt und analysiert. Es hat sich gezeigt, dass prinzipiell zwei Maßnahmen geeignet sind, die Fahrerreaktionszeit zu verkürzen: - Eine Flächen- und Leuchtdichtevergrößerung der Bremsleuchten wird von den nachfolgenden Fahrern intuitiv als Annäherung an das vorausfahrende Fahrzeug erkannt. - Blinkende Leuchten sind besonders geeignet, die Aufmerksamkeit des nachfolgenden Fahrers auch bei Ablenkung auf das verzögernde Fahrzeug zu lenken. Als mögliche Weiterentwicklung für ein optimiertes rückwärtiges Signalbild wird vorgeschlagen: Bei Ansprechen eines Bremsassistenten oder Antiblockiersystems (ABS) beziehungsweise einer Fahrzeugverzögerung über 7 m/s2 ist die Gefahrenbremsung über ein Blinken der dritten hochgesetzten Bremsleuchte mit 3-5 Hz zu signalisieren. Optional sollten sich zusätzlich die Flächen beziehungsweise Leuchtdichten der beiden unteren Bremsleuchten vergrößern. Diese Maßnahmen erfordern Änderungen in den ECE-Regelungen Nummer 7 und Nummer 48 sowie im Wiener Weltabkommen. Ziel des vorgestellten Lösungsvorschlags ist die Reduzierung der Zahl beziehungsweise Schwere von Auffahrunfällen.
Der Kraftschluss zwischen Reifen und Fahrbahn bestimmt in entscheidender Weise die Fahrsicherheit, insbesondere bei Nässe. Wer sein Fahrzeug mit breiteren Reifen ausrüsten will, hat oftmals keine Möglichkeit, die Eigenschaften der jeweiligen Reifen bei nachlassender Profiltiefe einzuschätzen. Es sollte in dieser Untersuchung geklärt werden, ob die Verwendung von Breitreifen Nachteile für die Fahrsicherheit bei Nässe mit sich bringt, insbesondere unter Berücksichtigung der im Betrieb zwangsläufig nachlassenden Profiltiefe. Im Innentrommelprüfstand der Bundesanstalt für Straßenwesen wurden Kraftschlussuntersuchungen an Pkw-Reifen in drei verschiedenen Breiten durchgeführt. Die Untersuchung beschäftigt sich mit dem Einfluss der Reifenbreite, der Profilgestaltung und der Profilhöhe auf den Kraftschluss bei Nässe. Dabei werden auch die Parameter Fahrgeschwindigkeit, Wasserfilmhöhe, Radlast und Reifeninnendruck berücksichtigt, die den Kraftschluss bei Nässe maßgeblich mitbestimmen. Steigende Fahrgeschwindigkeit, geringere Profiltiefe und höherer Wasserfilm verringern die maximal übertragbaren Bremskräfte. Höhere Radlasten verringern die Tendenz des Reifens, unter dem Druck des sich ausbildenden Wasserkeils aufzuschwimmen und verbessern dadurch das Kraftschlussverhalten bei Nässe. Niedrige Profilhöhen führen wegen der schlechter werdenden Wasserverdrängung zu einem stärkeren Abfall der Kraftschlussmaximalwerte bei steigender Geschwindigkeit oder höherem Wasserfilm. Insgesamt birgt die Kombination von hoher Fahrgeschwindigkeit, niedriger Profiltiefe und hohem Wasserfilm eine extrem hohe Aquaplaninggefahr, die sich noch verstärkt, wenn der korrekte Reifeninnendruck unterschritten wird. Bei niedrigen Fahrgeschwindigkeiten zeigen schmalere Reifen Vorteile, während bei höheren Fahrgeschwindigkeiten und niedrigen Wasserfilmhöhen Breitreifen das Niveau schmaler Reifen sogar übertreffen können. Dieser Effekt ist auf die spezielle laufrichtungsgebundene Profilgestaltung der hier untersuchten Breitreifen zurückzuführen.
Der Anteil von Geländefahrzeugen an der Gesamtzahl von Personenkraftwagen betrug im Juli 1991 in den alten Bundesländern ca. 1,1 Prozent. Nach eigenen Erhebungen sind etwa 62 Prozent der Geländefahrzeuge mit einem Frontschutzbügel ausgestattet. Der Bundesminister für Verkehr hat die BASt beauftragt zu prüfen, ob solche Konstruktionen einen Einfluss auf die Verletzungen bei Kollisionen mit Fußgängern und Zweiradbenutzern haben. Dazu wurde das Datenmaterial der Unfallerhebung der Medizinischen Hochschule Hannover ausgewertet und die um fahrzeugtechnische Angaben ergänzten Unfalldaten aus Nordrhein-Westfalen betrachtet. Weiterhin wird von Komponententests berichtet, die den Anprall menschlicher Körperteile an das Fahrzeug simulieren. Mit den Ergebnissen dieser Untersuchung wurde ein Frontschutzbügel hergestellt, der weniger aggressiv gegenüber ungeschützten Verkehrsteilnehmern ist. Zur Quantifizierung der Gefährdung von Fußgängern wurden zwei gängige Geländefahrzeugtypen mit und ohne Frontschutzbügel gemäß dem Prüfvorschlag der EEVC-WG 10 zur Bestimmung der Fußgängerverträglichkeit von Pkw-Frontflächen getestet. Die Ergebnisse aus den Versuchsreihen wurden mit Ergebnissen aus Versuchen an normalen Pkw verglichen.Es kann festgestellt werden, dass bei einem Unfall mit Kopfanprall eines Kindes an ein mit Frontschutzbügel ausgestattetes Geländefahrzeug bei 20 km/h mit gleichen Kopfbelastungen zu rechnen ist, wie bei einem Unfall mit 30 km/h mit einem Geländefahrzeug ohne Frontschutzbügel, beziehungsweise mit 40 km/h mit einem normalen Pkw. Für den Hüftanprall eines Erwachsenen an die Haubenkante ist bei einer Fahrzeuggeschwindigkeit von 25 km/h bei einem Fahrzeug mit Frontschutzbügel mit gleichen Belastungen zu rechnen, wie bei einem Unfall mit einem Fahrzeug ohne Frontschutzbügel bei 40 km/h (Pkw oder Geländewagen). Für die Belastungen des Knies eines Erwachsenen lässt sich keine Verschlechterung durch montierte Frontschutzbügel ableiten.
Künftig sollen in Kfz-Scheinwerfern anstelle von Glühlampen auch Gasentladungslampen eingesetzt werden können. Hierbei handelt es sich um Hochdruckentladungslampen, die sich von bisher eingesetzten Halogen-Glühlampen durch die spektrale Verteilung ihres Lichtes, eine höhere Leuchtdichte und einen größeren Lichtstrom - bei geringerer elektrischer Aufnahmeleistung - unterscheiden. Derzeit werden Lampen unter der Bezeichnung D 1 in ein deutsches Fahrzeug der gehobenen Klasse eingebaut. Im Rahmen einer Vorstudie innerhalb des Projektes wurden die folgenden Punkte untersucht: - Integrierbarkeit der Lampe und des Scheinwerfers in bestehende Regelungen; - lichttechnische Eigenschaften der Gasentladungssysteme wie Zünd- und Anlaufverhalten in unterschiedlichen Betriebszuständen; - Farbwiedergabe retroreflektierender Verkehrszeichen und Signaleinrichtungen; - Leuchtdichtekontraste bei retroreflektierenden Materialien und Rückstrahlern; - Sicherheitsaspekte; - Blendung des Gegen- und des vorausfahrenden Verkehr. In der anschließenden Hauptstudie wurden Vorwärtsreflexion an Fahrbahnoberflächen zur Bestimmung der indirekten Blendung im trockenen und nassen Zustand; - spektrale Reflexion von Fahrbahndecken; - Streuleuchtdichten vor dem Fahrzeug bei Schlechtwettersituationen; - Blendungsunterschiede zwischen konventionellen und Gasentladungs-Systemen; - Gradient der Hell-Dunkel-Grenze untersucht. Bei der Untersuchung der Vorwärtsreflexion zeigte sich, dass sich bei nassen Fahrbahnoberflächen das Maximum der Reflexion in Fahrtrichtung verschiebt. In Schlechtwettersituationen wurde durch den größeren Lichtstrom ein Anstieg der Streuleuchtdichte gemessen. Aus diesem Grunde scheint eine Begrenzung der Vorfeldbeleuchtungsstärke sinnvoll. Aufgrund der Fahrzeugdynamik ergeben sich verschiedene Gradienten der Hell-Dunkel-Grenzen. Sie sind abhängig vom Fahrzeugtyp sowie von der Ausstattung der Fahrzeuge mit Niveauregulierung und automatischer Leuchtweitenregelung. Es ergab sich bei Verwendung von Gasentladungssystemen eine Erhöhung der Blendung. Die Blendbeleuchtungsstärken lagen dabei höher als bei vergleichbaren Halogensystemen. Ebenso wird durch die Vorwärtsreflexion auf der Fahrbahnoberfläche eine erhöhte Blendbeleuchtungsstärke bewirkt. Es zeigte sich, dass insbesondere zur Ermittlung der Beeinflussung älterer Verkehrsteilnehmer durch Gasentladungslampen weitere Untersuchungen erforderlich sind.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
Die hier vorgestellten Forschungsprojekte hatten die Aufgabenstellung, - sinnvolle Obergrenzen für den biogenen Blend-Anteil im Kraftstoff aus ökonomisch-technischer Sicht aufzuzeigen sowie - technische Anforderungen an Pkw aus Altbestand und Neufahrzeugen für den Betrieb mit solchen Kraftstoff-Blends zu untersuchen, insbesondere in Hinblick auf Aspekte der Dauerhaltbarkeit. Auf Basis einer umfangreichen Literaturrecherche wurden zunächst sinnvolle Beimischungen ermittelt, die in 5 Fahrzeugen (3 Otto-Pkw, 2 Diesel-Pkw) auf einem Abgasrollenprüfstand getestet wurden. Anschließend wurden zwei Fahrzeuge einer Dauerlaufuntersuchung (ca. 80.000 km) unterzogen. Hierbei wurden u. a. Emissionsverhalten, Kraftstoffverbrauch und Motorleistung bewertet und Motorölproben entnommen. Am Ende der Dauerlaufuntersuchungen wurden bei beiden Fahrzeugen Motor und Kraftstoffsystem sorgfältig inspiziert. Aus fahrzeugtechnischer Sicht begrenzen bei Biodiesel vor allem die Ölverdünnung sowie der Anstieg der NOx-Emissionen den maximal möglichen Beimischungsanteil. Bei Bio-Alkohol sind insbesondere die Materialverträglichkeit und der Kraftstoffverbrauch limitierende Faktoren für erhöhte Beimischungen. Obwohl die betrachteten Euro-5-Fahrzeuge nicht für den Betrieb mit erhöhten Beimengungen an Biokraftstoffen ausgelegt waren, wurden die maßgeblichen Grenzwerte für die limitierten Emissionen im Verlauf der Untersuchungen nicht überschritten. Mit Ausnahme von NOx bei den Dieselfahrzeugen wurden darüber hinaus sogar die Euro-6-Grenzwerte unterschritten.
The objective was to develop and validate a crash trolley (reference vehicle) equipped with a compartment and a full restraint system for driver and front seat passenger which can be used in full scale crash testing. Furthermore, the crash trolley should have a suspension to show rotation and nick effects similar to real vehicles. Within the development phase the reference vehicle was build based on a European family car. Special attention was needed to provide appropriate strength to the trolley and its suspension. The reference vehicle is equipped with a restraint system consisting of airbags, pedals, seats, dashboard, and windscreen. On the front of the vehicle different crash barriers can be installed to provide miscellaneous deceleration pulses. For the validation phase a series of low and high speed crash tests with HIII dummies were conducted and compared with full scale tests. For the comparison deceleration pulse, dummy numbers and vehicle movement were analyzed. Validation tests with velocities up to 60 km/h showed promising results. The compartment and the suspension systems stayed stable. Rotation effects were comparable with full scale car crash tests. The airbags and seat belt system worked reasonable. The acceleration pulse compared to an Euro NCAP test had a similar characteristic but was in general slightly lower. After the successful validation the reference vehicle is already in use in different studies in the field of vehicle safety research at BASt.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
Aktive Systeme der passiven Fahrzeugsicherheit zum Fußgängerschutz, sogenannte crash-aktive Fußgängerschutzsysteme, werden seit 2005 zur Erfüllung der gesetzlichen Anforderungen (siehe Verordnung (EG) Nr. 78/2009 und 631/2009) in Serienfahrzeugen eingesetzt. Diese crash-aktiven Fußgängerschutzsysteme stellen im Gegensatz zu den rein passiven Systemen nur eine instationäre Lösung dar. Da die innerhalb der gesetzlichen Anforderungen definierten Testverfahren zur Bewertung stationärer Systeme entwickelt wurden, können derzeit mögliche Risiken instationärer Systeme nicht berücksichtigt werden. Im Rahmen dieses Forschungsprojektes soll ein Bewertungsverfahren für diese crash-aktiven Fußgängerschutzsysteme entwickelt werden, welches das reale Potential dieser Systeme möglichst gut wiedergibt. Basis hierfür soll eine umfangreiche Untersuchung zusätzlicher Risiken bilden. Die hier untersuchten instationären Schutzmaßnahmen werden nur im Falle eines Fahrzeuganpralls gegen Fußgänger aktiviert, der daher zuverlässig erkannt werden muss. Für die hierfür eingesetzten, kontaktbasierten Sensorsysteme stellen Fußgänger mit geringen Lasteinträgen in die Fahrzeugfront eine große Herausforderung dar. Die Lasteinträge hängen von zahlreichen Faktoren, wie bspw. der Höhe der entsprechenden Krafteinleitungspfade sowie der Größe und dem Gewichts des Fußgängers, ab. Mit Hilfe von umfangreichen Anprallversuchen und -simulationen wird gezeigt, dass die bisher eingesetzten Prüfkörper nur zum Teil für die Erfüllung dieser Anforderungen geeignet sind. Für ein geeignetes Prüfverfahren müssen daher neue Prüfkörper entwickelt werden. Durch die Aktivierung der Schutzmaßnahme soll bei den crash-aktiven Systemen vor allem das Verletzungsrisiko beim Kopfanprall verringert werden. Hierfür wird häufig die hintere Motorhaubenkante angehoben, um zusätzlichen Deformationsfreiraum zur Verfügung zu stellen. Die Haubenanhebung kann jedoch auch in zusätzlichen Verletzungsrisiken resultieren, bspw. durch die exponierte hintere Haubenkante oder die Verringerung des Deformationsfreiraums in Folge des Oberkörperanpralls. Ein Ersatzprüfverfahren zur Bewertung der Haubendeformation mit Hilfe des Hüftimpaktors wird vorgestellt. Ein hybrides Testverfahren bestehend aus Simulation und Versuch eignet sich für eine objektive Bewertung dieser Systeme, wobei die entsprechenden Versuchsparameter mit Hilfe der vorherigen Simulation bestimmt werden können.
The objectives of the FIMCAR (Frontal Impact and Compatibility Assessment Research) project are to answer the remaining open questions identified in earlier projects (such as understanding of the advantages and disadvantages of force based metrics and barrier deformation based metrics, confirmation of specific compatibility issues such as structural interaction, investigation of force matching) and to finalise the frontal impact test procedures required to assess compatibility. Research strategies and priorities were based on earlier research programs and the FIMCAR accident data analysis. The identified real world safety issues were used to develop a list of compatibility characteristics which were then prioritised within the consortium. This list was the basis for evaluating the different test candidates. This analysis resulted in the combination of the Full Width Deformable Barrier test (FWDB) with compatibility metrics and the existing Offset Deformable Barrier (ODB) as described in UN-ECE Regulation 94 with additional cabin integrity requirement as being proposed as the FIMCAR assessment approach. The proposed frontal impact assessment approach addresses many of the issues identified by the FIMCAR consortium but not all frontal impact and compatibility issues could be addressed.
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for over 10 years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and the final report to the steering committee on frontal impact [Faerber 2007] and the FP5 VC-COMPAT[Edwards 2007] project activities, two test approaches were identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in current research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis will be performed. In the FIMCAR Deliverable D 3.1 [Adolph 2013] the development and assessment of criteria and associated performance limits for the full width test procedure were reported. In this Deliverable D3.2 analyses of the test data (full width tests, car-to-car tests and component tests), further development and validation of the full width assessment protocol and development of the load cell and load cell wall specification are reported. The FIMCAR full-width assessment procedure consists of a 50 km/h test against the Full Width Deformable Barrier (FWDB). The Load Cell Wall behind the deformable element assesses whether or not important Energy Absorbing Structures are within the Common Interaction Zone as defined based on the US part 581 zone. The metric evaluates the row forces and requires that the forces directly above and below the centre line of the Common Interaction Zone exceed a minimum threshold. Analysis of the load spreading showed that metrics that rely on sum forces of rows and columns are within acceptable tolerances. Furthermore it was concluded that the Repeatability and Reproducibility of the FWDB test is acceptable. The FWDB test was shown to be capable to detect lower load paths that are beneficial in car-to-car impacts.
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for over 10 years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in current research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The objectives of the work reported in this deliverable were to review existing full-width test procedures and their discussed compatibility metrics, to report recent activities and findings with respect to full-width assessment procedures and to assess test procedures and metrics. Starting with a review of previous work, candidate metrics and associated performance limits to assess a vehicle- structural interaction potential, in particular its structural alignment, have been developed for both the Full Width Deformable Barrier (FWDB) and Full Width Rigid Barrier (FWRB) tests. Initial work was performed to develop a concept to assess a vehicle- frontal force matching. However, based on the accident analyses performed within FIMCAR frontal force matching was not evaluated as a first priority and thus in line with FIMCAR strategy the focus was put on the development of metrics for the assessment of structural interaction which was evaluated as a first priority.
Cost benefit analysis
(2014)
Although the number of road accident casualties in Europe is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities [EC 2012]. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car- safety performance in frontal impacts is to improve its compatibility for car-to-car impacts and for collisions against objects and HGVs. Compatibility consists of improving both a car- self and partner protection in a manner such that there is good interaction with the collision partner and the impact energy is absorbed in the car- frontal structures in a controlled way which results in a reduction of injuries. Over the last ten years much research has been performed which has found that there are four main factors related to a car- compatibility [Edwards 2003, Edwards 2007]. These are structural interaction potential, frontal force matching, compartment strength and the compartment deceleration pulse and related restraint system performance. The objective of the FIMCAR FP7 EC-project was to develop an assessment approach suitable for regulatory application to control a car- frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation.