91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
Schlagworte
- Impact test (veh) (45) (entfernen)
Institut
- Abteilung Fahrzeugtechnik (36)
- Sonstige (21)
- Abteilung Straßenverkehrstechnik (1)
- Präsident (1)
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
Abstract: Für Kinder in Deutschland existiert im Pkw weiterhin ein höheres Risiko, im Straßenverkehr bei einem Unfall schwer verletzt oder getötet zu werden, als es für ungeschützte Verkehrsteilnehmer wie Fahrradfahrer oder Fußgänger besteht. Dies erscheint auf den ersten Blick nicht nachvollziehbar, da der Pkw und die vorgeschriebenen Kindersitze den Kindern eine hohe Sicherheit bieten müssten. Der vorliegende Projektbericht gibt Aufschluss über den aktuellen Stand der Sicherheit von Kindern im Pkw in Deutschland und zeigt Optimierungspotenzial auf. Die Schutzwirkung der Kindersitze hängt von mehreren Faktoren ab. Dabei stehen technische Aspekte, die hier detailliert untersucht wurden, im Vordergrund. Doch vor allem in den letzten Jahren zeigte sich immer wieder in Feldstudien, aber auch in der Unfallanalyse, dass Kinderschutzsysteme (KSS) oftmals nicht nach den Vorgaben installiert wurden. Wenn der Kindersitz und/oder das Kind nicht entsprechend der Bedienungsanleitung gesichert werden, kann sich das Schutzpotenzial der KSS reduzieren und gegen Null gehen. Im schlimmsten Fall stellt eine fehlerhafte Benutzung von KSS eine Gefahr sowohl für das Kind als auch für andere Pkw-Insassen dar. Die Unfallanalyse ergab keine Aussage darüber, ob verschiedene KSS-Modelle zu unterschiedlichen Verletzungsmustern führen, da die Unfallkonstellationen pro KSS-Modell zu verschieden waren. Des Weiteren wurde analysiert, inwieweit heutige Testverfahren mit diesen Konstellationen übereinstimmen. Das Ziel, mit wenigen Verfahren möglichst alle relevanten Unfälle abzubilden, wurde zum Teil ereicht. Zu viele Testverfahren mit unterschiedlichen Bewertungssystemen stellen heutzutage die Endverbraucher vor das Problem, dass nicht klar ist, welches KSS wirklich das beste ist. In der Realität hängt die Schutzwirkung zudem noch wesentlich von der KSS-Pkw-Kombination ab, die nur annähernd durch Versuche überprüft werden kann, da sich eine zu hohe Anzahl von Kombinationsmöglichkeiten ergibt. Anhand von mehr als 100 Versuchen wurde das Schutzpotenzial von verschiedenen aktuellen Kindersitzmodellen untersucht. Dabei wurden immer vermeintlich gute und schlechte KSS gegenübergestellt und unter gleichen Randbedingungen getestet. Ziel dieses Vorgehens war es, anhand der Messergebnisse Maßnahmen zu erkennen, die dem Schutz der Kinder dienlich sind. Zusammenfassend kann gesagt werden, dass prinzipiell für Kinder ein gutes Schutzniveau durch KSS besteht, was aber von KSS zu KSS verschieden sein kann. Die teureren KSS wiesen keine mechanische Zerstörung auf und überstanden alle Tests ohne ernsthafte Beschädigungen. Lediglich das oftmals als Dämpfungsmaterial eingesetzte Polystyrol nahm Energie auf und verformte sich wie vorgesehen plastisch. Bei den "Billig-Kindersitzen" ergab sich leider ein komplett anderes Bild. Sobald die Anforderungen über die der Gesetzgebung hinausgehen, ist immer weniger Schutz für die Kinder vorhanden. Besonders im Seitenaufprall offenbarten sich erhebliche Lücken in der Sicherheit. Dies reichte von mechanischem Versagen mancher Plastikteile bis hin zu konstruktiven Unzulänglichkeiten. Vor allem die Gurtführung muss deutlicher gekennzeichnet und mechanisch verstärkt werden. Trotz des hohen Schutzpotenzials einiger Kindersitze ist das Ende der Entwicklung noch nicht abzusehen. In allen Kindersitzklassen ist es prinzipiell möglich, die Belastungswerte weiter zu reduzieren. Dazu werden am Ende des Berichtes verschiedene Möglichkeiten aufgezeigt. Zum einen ist dies eine optimierte Babyschale, die durch eine Trägheitsbewegung gezielt Energie abbaut und das Baby in eine günstigere Position bringt, in der die Belastungen des Körpers reduziert sind. Zum anderen wird gezeigt, dass durch die feste Anbindung des KSS an den Pkw und die Reduzierung der Rotation um die Y-Achse die Belastungen für Kinder reduziert werden können. Größtes Entwicklungspotenzial bietet dabei das ISOFIX-System. Es ist bekannt, dass ISOFIX die Fehlbedienung des Kindersitzes und die Belastungen der Kinder deutlich reduzieren kann. Trotzdem ist die bisherige Marktdurchdringung von ISOFIX eher gering. Obwohl insgesamt ein positives Fazit gezogen werden kann, darf nicht aufgehört werden, die Kindersicherheit weiter zu verbessern. Denn nicht alle Kindersitze schützen heute gleich gut. Einige genügen lediglich den Gesetzesansprüchen und finden in vielen Fällen durch einen sehr geringen Verkaufspreis Zugang in die Pkw. Durch verschärfte Testbedingungen sollten diese Kindersitze abgeschafft und der Weg für neue und bessere Kinderschutzsysteme frei gemacht werden.
The off-set assessment procedure potentially contributes to the FIMCAR objectives to maintain the compartment strength and to assess load spreading in frontal collisions. Furthermore it provides the opportunity to assess the restraint system performance with different pulses if combined with a full-width assessment procedure in the frontal assessment approach. Originally it was expected that the PDB assessment procedure would be selected for the FIMCAR assessment approach. However, it was not possible to deliver a compatibility metric in time so that the current off-set procedure (ODB as used in UNECE R94) with some minor modifications was proposed for the FIMCAR Assessment Approach. Nevertheless the potential to assess load spreading, which appears not to be possible with any other assessed frontal impact assessment procedure was considered to be still high. Therefore the development work for the PDB assessment procedure did not stop with the decision not to select the PDB procedure. As a result of the decisions to use the current ODB and to further develop the PDB procedure, both are covered within this deliverable. The deliverable describes the off-set test procedure that will be recommended by FIMCAR consortium, this corresponds to the ODB test as it is specified in UN-ECE Regulation 94 (R94), i.e. EEVC deformable element with 40% overlap at a test speed of 56 km/h. In addition to the current R94 requirements, FIMCAR will recommend to introduce some structural requirements which will guarantee sufficiently strong occupant compartments by enforcing the stability of the forward occupant cell. With respect to the PDB assessment procedure a new metric, Digital Derivative in Y direction - DDY, was developed, described, analysed, and compared with other metrics. The DDY metric analyses the deformation gradients laterally across the PDB face. The more even the deformation, the lower the DDY values and the better the metric- result. In order analyse the different metrics, analysis of the existing PDB test results and the results of the performed simulation studies was performed. In addition, an assessment of artificial deformation profiles with the metrics took place. This analysis shows that there are still issues with the DDY metric but it appears that it is possible to solve them with future optimisations. For example the current metric assesses only the area within 60% of the half vehicle width. For vehicles that have the longitudinals further outboard, the metric is not effective. In addition to the metric development, practical issues of the PDB tests such as the definition of a scan procedure for the analysis of the deformation pattern including the validation of the scanning procedure by the analysis of 3 different scans at different locations of the same barrier were addressed. Furthermore the repeatability and reproducibility of the PDB was analysed. The barrier deformation readings seem to be sensitive with respect to the impact accuracy. In total, the deliverable is meant to define the FIMCAR off-set assessment procedure and to be a starting point for further development of the PDB assessment procedure.
Sowohl mit dem 3. Road Safety Action Programme der Europäischen Kommission als auch mit dem deutschen Verkehrssicherheitsprogramm werden die verkehrspolitischen Zielsetzungen zur Erhöhung der Verkehrssicherheit in Europa und Deutschland festgelegt. Hierbei muss die passive Fahrzeugsicherheit auch weiterhin eine bedeutende Rolle übernehmen. Es ist jedoch auch festzustellen, dass durch den zunehmenden Einsatz von Elektronik im Fahrzeug die klassischen Bereiche der aktiven und passiven Fahrzeugsicherheit mehr und mehr ineinander greifen. Der Fortschritt in der Elektronik ermöglicht eine Integration der Systeme der aktiven und passiven Sicherheit. Dadurch lässt sich die Fahrzeugsicherheit weiter steigern. Durch die Vernetzung der Systeme lassen sich sogar Kosten einsparen. Der europäische Regierungsausschuss EEVC (European Enhanced Vehicle-safety Committee), die Verbraucherschutzorganisation Euro NCAP (European New Car Assessment Programme) und die Europäische Kommission mit der eSafety Initiative haben diesen Trend erkannt und entsprechende Aktivitäten eingeleitet.
The objective of this deliverable is to describe the expected influence of the candidate test procedures developed in FIMCAR for frontal impact on other impact types. The other impact types of primary interest are front-to-side impacts, collisions with road restraint systems (e.g. guardrails), and heavy goods vehicle impacts. These collision types were chosen as they involve structures that can be adapted to improve safety. Collisions with vulnerable road users (VRU) were not explicitly investigated in FIMCAR. It is expected that the vehicle structures of interest in FIMCAR can be designed into a VRU friendly shell. Information used for this deliverable comes from simulations and car-to-car crash tests conducted in FIMCAR or review of previous research. Three test configurations (full width, offset, and moving deformable barriers) were the input to the FIMCAR selection process. There are three different types of offset tests and two different full width tests. During the project test procedures could be divided into three groups that provide different influences or outcomes on vehicle designs: 1. The ODB barrier provides a method to assess part of the vehicles energy absorption capabilities and compartment test in one test. 2. The FWRB and FWDB have similar capabilities to control structural alignment, further assess energy absorption capabilities, and promote the improvements in the occupant restraint system for high deceleration impacts. 3. The PDB and MPDB can be used to promote better load spreading in the vehicle structures, in addition to assessing energy absorption and occupant compartment strength in an offset configuration. The consortium selected the ODB and FWDB as the two best candidates for short term application in international rulemaking. The review of how all candidates would affect vehicle performance in other impacts (beside front-to-front vehicle or frontal impacts with fixed obstacles) however is reported in this deliverable to support the benefit analysis reported in FIMCAR. The grouping presented above is used to discuss all five test candidates using similarities between certain tests and thereby simplify the discussion.
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for over 10 years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and the final report to the steering committee on frontal impact [Faerber 2007] and the FP5 VC-COMPAT[Edwards 2007] project activities, two test approaches were identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in current research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis will be performed. In the FIMCAR Deliverable D 3.1 [Adolph 2013] the development and assessment of criteria and associated performance limits for the full width test procedure were reported. In this Deliverable D3.2 analyses of the test data (full width tests, car-to-car tests and component tests), further development and validation of the full width assessment protocol and development of the load cell and load cell wall specification are reported. The FIMCAR full-width assessment procedure consists of a 50 km/h test against the Full Width Deformable Barrier (FWDB). The Load Cell Wall behind the deformable element assesses whether or not important Energy Absorbing Structures are within the Common Interaction Zone as defined based on the US part 581 zone. The metric evaluates the row forces and requires that the forces directly above and below the centre line of the Common Interaction Zone exceed a minimum threshold. Analysis of the load spreading showed that metrics that rely on sum forces of rows and columns are within acceptable tolerances. Furthermore it was concluded that the Repeatability and Reproducibility of the FWDB test is acceptable. The FWDB test was shown to be capable to detect lower load paths that are beneficial in car-to-car impacts.
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for over 10 years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in current research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The objectives of the work reported in this deliverable were to review existing full-width test procedures and their discussed compatibility metrics, to report recent activities and findings with respect to full-width assessment procedures and to assess test procedures and metrics. Starting with a review of previous work, candidate metrics and associated performance limits to assess a vehicle- structural interaction potential, in particular its structural alignment, have been developed for both the Full Width Deformable Barrier (FWDB) and Full Width Rigid Barrier (FWRB) tests. Initial work was performed to develop a concept to assess a vehicle- frontal force matching. However, based on the accident analyses performed within FIMCAR frontal force matching was not evaluated as a first priority and thus in line with FIMCAR strategy the focus was put on the development of metrics for the assessment of structural interaction which was evaluated as a first priority.
The objectives of the FIMCAR (Frontal Impact and Compatibility Assessment Research) project are to answer the remaining open questions identified in earlier projects (such as understanding of the advantages and disadvantages of force based metrics and barrier deformation based metrics, confirmation of specific compatibility issues such as structural interaction, investigation of force matching) and to finalise the frontal impact test procedures required to assess compatibility. Research strategies and priorities were based on earlier research programs and the FIMCAR accident data analysis. The identified real world safety issues were used to develop a list of compatibility characteristics which were then prioritised within the consortium. This list was the basis for evaluating the different test candidates. This analysis resulted in the combination of the Full Width Deformable Barrier test (FWDB) with compatibility metrics and the existing Offset Deformable Barrier (ODB) as described in UN-ECE Regulation 94 with additional cabin integrity requirement as being proposed as the FIMCAR assessment approach. The proposed frontal impact assessment approach addresses many of the issues identified by the FIMCAR consortium but not all frontal impact and compatibility issues could be addressed.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.
Since integrated safety systems combine active and passive safety elements in one safety system, it is necessary to define new procedures to evaluate vehicle safety from the overall system point of view. The main goal of the ASSESS project is to develop harmonized and standardized assessment procedures for collision mitigation and avoidance systems. Methods and Data Sources: In ASSESS, procedures are developed for: driver behaviour evaluation, pre-crash system performance evaluation, crash performance evaluation, socio-economic assessment. This paper will concentrate on the activities related to the crash evaluation. The objective is to perform simulations, sled tests and crash tests in order tounderstand the influence of the activation of the pre-crash systems on the occupants" injuries during the crash phase. When a traffic accident is unavoidable, pre-crash systems work on various safety devices in order to improve the vehicle occupants" protection. Braking assistance and adaptive restraint systems are the main pre-crash systems whose effect on the occupants" protection will be described in this paper. Results: The results will be a description of the effect of the activation of the pre-crash systems on the crash phase. Additionally, a set of recommendations for future methodology developments will be delivered. Furthermore, a first approach to the study of the effect of the pre-crash systems activation on the occupants" protection when the impact is unavoidable will be presented. This effect will be quantified using the biomechanical values obtained from the simulation and testing activities and their related injury risks. Simulation and testing activities will consider the following scenarios: - No activation of any pre-crash system, - Activation of one or a combination of several pre-crash systems. In this way, differences in the results obtained from different scenarios will show the effect of each pre-crash system separately during the crash phase. Discussion and Limitations: The set of activities developed in this research project is limited by the fact that with the given resources only a limited number of vehicle models could be investigated. In addition, there are also limitations related to the injury risk curves and the passive safety tools currently on the market. Conclusion and Relevance to session submitted: The paper will present a complete analysis of the effect of pre-crash systems during the crash phase when the impact is unavoidable. Details, limitations and first application experience based on a few examples will be discussed. Currently, there is not any regulation, assessment program, or other similar official procedure able to assess pre-crash systems during the crash phase. This project comprises phases of traffic accidents which have been historically analysed separately, and aims to evaluate them taking into account their interrelationship. ASSESS is one of the first European projects which deals in depth with the concept of integrated safety, defining methodologies to analyse vehicle safety from a global point of view.
Seit 1997 gibt es in Europa unter dem Namen Euro NCAP (European New Car Assessment Programme) einheitliche Test- und Ratingverfahren. Sie liefern Informationen über den Insassen- und über den Fußgängerschutz. Euro NCAP hat seither fast 90 Fahrzeugmodelle in jeweils drei unterschiedlichen Crashtest-Konfigurationen untersucht und die Ergebnisse den europäischen Konsumenten zugänglich gemacht. Im Beitrag wird auf die Testbedingungen, die Euro NCAP-Ratingverfahren sowie auf die Weiterentwicklung von Euro NCAP eingegangen. Ein wichtiger Aspekt wird dabei auch die weltweite Harmonisierung der Test- und Ratingverfahren sein.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
Es ist zu beobachten, dass trotz einer Abnahme der Zahl der Verletzungen und der Verletzungsschwere der Insassen bei Pkw-Unfällen Halswirbelsäulen (HWS)-Distorsionen, speziell im unteren Geschwindigkeitsbereich häufiger auftreten. Neben anderen Faktoren werden auch veränderte Beschleunigungs- und Verzögerungsimpulse, die im Crashfall auf die Insassen wirken, als möglicherweise ursächlich für die Entstehung von HWS-Distorsionen angesehen. In der vorliegenden Arbeit wird untersucht, welchen Einfluss konstruktive Veränderungen, die durch Versicherungseinstufungstests bedingt werden, auf die Beschleunigungs- und Verzögerungsimpulse im Fahrzeuginnenraum haben. Versuche zum Fußgängerschutz wurden einvernehmlich nicht durchgeführt, da die Fahrzeuge noch nicht konsequent nach Fußgängerschutzkriterien konzipiert werden. Die Untersuchungsmethode lässt sich gliedern in: - Analyse von internationalen Versicherungssystemen und Analyse der aus den Versicherungseinstufungstests resultierenden Veränderungen von Fahrzeugstrukturen; - Durchführung und Analyse von eigenen Aufprallversuchen mit Fahrzeugteilstrukturen und vergleichende Analyse von Vollfahrzeugversuchen der Versicherungswirtschaft; Zusammenführen der getätigten Schritte. Bei der Ersteinstufung eines Pkw in die Vollversicherung dient der Versicherungseinstufungstest des RCAR/AZT (Prüfgeschwindigkeit 15 km/h) zur Bestimmung der Schadenshöhe und damit zur Einstufung in eine Typklasse. In vielen weiteren Staaten dienen dieser oder ähnliche Tests zur Bewertung der Reparaturfreundlichkeit von Pkw. Um bei einem Versicherungseinstufungstest den Schaden möglichst gering zu halten, haben nahezu alle Neufahrzeuge Querträgersysteme mit kostenarm wechselbaren Absorptionselementen, die die Crashenergie gezielt auf kurzem Weg aufnehmen. Durch die neu EG-Richtlinie 2003/102/EG zum Fußgängerschutz müssen zukünftig hinter der Stoßfängeraußenhaut und vor dem massiven Querträger weiche Schäume untergebracht werden. Der Bauraum für Querträger und Energieabsorptionselemente wird dadurch weiter eingeschränkt. Diese Anforderungen veranlassen die Hersteller dazu, die Energieabsorptionselemente steifer zu gestalten, um einen effektiven Energieabbau bei kurzen Stopplängen zu gewährleisten. Durch diese Maßnahmen wird zwar der Insassenschutz bei Frontalaufprallen im Hochgeschwindigkeitsbereich verbessert, es werden aber zugleich höhere Innenraumverzögerungen (schnellerer Anstieg, höhere mittlere Verzögerung) bei Crashs im gesamten Geschwindigkeitsbereich erzeugt. Eine durchgeführte Korrelation zwischen konstruktiven Veränderungen am Fahrzeug und empirisch bestimmten Verzögerungsverläufen zeigte, dass eine günstigere Einstufung in der Fahrzeugvollversicherung nicht zwangsläufig höhere Verzögerungsimpulse für den Innenraum bedingen muss. Bei der Analyse von 172 Crashversuchen des Allianz Zentrums für Technik mit Neufahrzeugen aus den Jahren 1992 bis 2003 zeichnen sich aber statistisch bedeutsame ßnderungen in den Verzögerungsverläufen über die Prüfjahre ab: - Anstieg der Verzögerung wird steiler; - Mittelwert der Verzögerung wird grösser; - Zeitdauer bis zum Auftreten der maximalen Verzögerung wird kürzer; - dynamische Gesamtdeformation wird kleiner. Die steife Auslegung der für den Versicherungseinstufungstest relevanten Crashteile verbessert den Insassenschutz bei Hochgeschwindigkeitscrashs. Wenn es sich aber durch weitere Untersuchungen bestätigt, dass höhere Verzögerungs- beziehungsweise Beschleunigungsimpulse die Auftretenswahrscheinlichkeit von HWS-Verletzungen im Niedriggeschwindigkeitsbereich vergrößern, so sollten gezielt Maßnahmen zur Verringerung dieser Verletzungsrisiken ergriffen werden. Dazu gehören die weitere Optimierung der Sitzstrukturen einschließlich der Kopfstützen und die Entwicklung adaptiver Crashstrukturen, die dem Crashfall angepasste Kraft-Weg-Kennlinien ermöglichen.
Von der Bundesanstalt für Straßenwesen (BASt) und dem Rheinisch-Westfälischen TÜV wurde 1988/89 eine Pilotstudie zum Einfluss der Korrosion auf die passive Sicherheit von Pkw bei drei unterschiedlichen Fahrzeugtypen durchgeführt. Es wurde je ein dem Alter entsprechend durchschnittlich durch Korrosion geschädigtes älteres und ein möglichst gering geschädigtes jüngeres Fahrzeug bezüglich des Korrosionszustandes vermessen und im Aufprallversuch getestet. Bei den von der BASt durchgeführten Wandaufpralltests versagten insbesondere bei den älteren Fahrzeugen sicherheitsrelevante Fahrzeugteile. Es wurde daraufhin beschlossen, die Pilotstudie mit der vorliegenden zweiten Untersuchung unter den folgenden zwei Vorgaben fortzuführen: - Verbreiterung der Datenbasis von Tests mit weiteren Fahrzeugtypen mit starker Korrosion. - Prüfung von Fahrzeugen des gleichen Typs wie in der Pilotstudie, jedoch sollten an ihnen Korrosionsschutzmaßnahmen verwirklicht sein, welche die Automobilindustrie mit Beginn der 80er Jahre in die Fertigung eingeführt hatte. Die stark korrodierten Fahrzeuge der jetzt vorliegenden Untersuchung zeigten ein ähnliches Versagensspektrum wie die stark korrodierten Fahrzeuge der Pilotstudie. An den korrosionsgeschützten und auch jüngeren Nachfolgemodellen der Fahrzeuge der Pilotstudie konnte kein korrosionsbedingter Einfluss auf die passive Fahzeugsicherheit mehr gefunden werden.