Whiplash injuries are characterized by the high variability of its symptoms and by the subjectivity of its diagnosis, which sometimes leads to frauds perpetrated by victims of rear-end impacts. It is estimated that whiplash injuries cost annually about 10.000 million Euros in Europe. Therefore, the aim of this study was to investigate the influence of the dynamics of the accident in which the victim was involved in the probability of development of whiplash associated injuries. In the presented methodology, first an accident reconstruction is performed where the dynamics of the accident is determined. This is carried out using the software PC-Crash, police and insurance companies' data. Then biomechanical injuries criteria related with whiplash injuries are evaluated. For the evaluation of the probability of having whiplash injuries, the Neck Injury Criterion (NIC) of the victim and the mean acceleration of the vehicle were evaluated. Then, with medical reports, the results of the accident reconstruction are correlated with the reported injuries. Some examples are presented. The results obtained indicate that the study of the dynamics of the road accidents in which the victims were involved could be used as an auxiliary of the prognosis of whiplash injuries and is important for a precise diagnosis of this type of injuries.
A national initiative from the vehicle manufacturers, safety system suppliers, the road administration and universities in Sweden took off in 2007. The aim was to develop a national investigation network and a methodology focusing on all phases of a crash (pre-crash, in-crash and post-crash) as well as all parts of the road transport system (road user, vehicle and road environment). The initiative is formally run as a project with the acronym INTACT (Investigation Network and Accident Collection Techniques). It was a three year pilot with the aim to develop methodologies for an extended national crash investigation activity. During the first year the INTACT partners agreed on the aim for the investigation and methods for retrieving the data were developed. During the second and third year the methodology was tested in real-world investigations and further refinement was made. The paper describes the methodology developed to obtain high qualitative in-depth road crash data.
The overall purpose of the ASSESS project is to develop a relevant and standardised set of test and assessment methods and associated tools for integrated vehicle safety systems, primarily focussing on currently available pre-crash sensing systems. The first stage of the project was to define casualty relevant accident scenarios so that the test scenarios will be developed based on accident scenarios which currently result in the greatest injury outcome, measured by a combination of casualty severity and casualty frequency. The first analysis stage was completed using data from a range of accident databases, including those which were nationally representative (STATS19, UK and STRADA, SE) and in-depth sources which provided more detailed parameters to characterise the accident scenarios (GIDAS, DE and OTS, UK). A common analysis method was developed in order to compare the data from these different sources, and while the data sets were not completely compatible, the majority of the data was aligned in such a way that allowed a useful comparison to be made. As the ASSESS project focuses on pre-crash sensing systems fitted to passenger cars, the data selected for the analysis was "injury accidents which involved at least one passenger car". The accident data analysis yielded the following ranked list of most relevant accident scenarios: Rank Accident scenario 1 Driving accident - single vehicle loss of control 2 Accidents in longitudinal traffic (same and opposite directions) 3 Accidents with turning vehicle(s) or crossing paths in junctions 4 Accidents involving pedestrians The ranked list highlights the relatively large role played by "accidents in longitudinal traffic", and "accidents with turning vehicle(s) or crossing paths in junctions" (the second and third most prevalent accident scenarios, respectively). The pre-crash systems addressed in ASSESS propose to yield beneficial safety outcomes with specific regard to these accident scenarios. This indicates that the ASSESS project is highly relevant to the current casualty crash problem. In the second stage of the analysis a selection of these accident scenarios were analysed further to define the accident parameters at a more detailed level .This paper describes the analysis approach and results from the first analysis stage.
The SafetyNet project was formulated in part to address the need for safety oriented European road accident data. One of the main tasks included within the project was the development of a methodology for better understanding of accident causation together with the development of an associated database involving data obtained from on-scene or "nearly onscene" accident investigations. Information from these investigations was complemented by data from follow-up interviews with crash participants to determine critical events and contributory factors to the accident occurrence. A method for classification of accident contributing factors, known as DREAM 3.0, was developed and tested in conjunction with the SafetyNet activities. Collection of data and case analysis for some 1 000 individual crashes have recently been completed and inserted into the database and therefore aggregation analyses of the data are now being undertaken. This paper describes the methodology development, an overview of the database and the initial aggregation analyses.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
The main focus of the benefit estimation of advanced safety systems with a warning interface by simulation is on the driver. The driver is the only link between the algorithm of the safety system and the vehicle, which makes the setup of a driver model for such simulations very important. This paper describes an approach for the use of a statistical driver model in simulation. It also gives an outlook on further work on this topic. The build-up process of the model suffices with a distribution of reaction times and a distribution of reaction intensities. Both were combined in different scenarios for every driver. Each scenario has then a specific probability to occur. To use the statistical driver model, every accident scene has to be simulated with each driver scenario (combinations of reaction times and intensities). The results of the simulations are then combined regarding the probabilities to occur, which leads to an overall estimated benefit of the specific system. The model works with one or more equipped participants and delivers a range for the benefit of advanced safety systems with warning interfaces.
Millions of kilometers are driven and recorded by car manufacturers and researchers every year to gather information about realistic traffic situations. The focus of these studies is often the recording of critical situations to create test scenarios for the development of new systems before introducing them into the market. This paper shows a novel Analysis and Investigation Method for All Traffic Scenarios (AIMATS) based on real traffic scenes. It also shows how to get detailed information about speeds, trajectories and behavior of all participants without driving thousands of kilometers at the example of conflict situations with animals. Basis of the AIMATS is the identification of the most relevant locations as "Points of Interest" (POI), the recording of the critical situations and their "base lines" at these POI. This paper presents a new method to identify critical scenarios involving both vehicles and animals as well as preliminary results of a study done in Saxony using this new method.
The focus of the technical innovation in the automobile industry is currently changing to sensor based safety systems, which are operating in the pre-crash phase of an accident. To get more information about this pre-crash phase for real accidents a simulation of this phase using the GIDAS database is done. The basics for this simulation are geometrical information about the accident location and the exact accident data out of the GIDAS database. This aggregated information gives the possibility to simulate an exact motion for every accident participant, using MATLAB / SIMULINK, in the pre-crash phase. After the simulation the information about the geometrical positions, the velocities and maneuvers of the drivers to an individual TTC (time to collision) are available. With those results it is possible to develop new useful sensor geometries using pre-crash scatter plots or estimate the efficiency of implemented active safety systems in combination with sensor characteristics. This simulation can be done for every reconstructed accident included in the GIDAS database, so these results can represent a wide spread basis for the further development of active safety systems and sensor geometries and characteristics
Entgegen populären Meinungen, welche älteren Kraftfahrern ein generelles Gefahrenpotenzial für die allgemeine Verkehrssicherheit zuschreiben, weisen die Unfallstatistiken eher auf eine besondere Gefährdung dieser Gruppe von Verkehrsteilnehmern hin, woraus sich Forderungen nach einer zielgruppenspezifischen Verkehrssicherheitsarbeit begründen. Kompetentes und damit sicheres Verhalten kann als Ergebnis der Passung zwischen den individuell verfügbaren Ressourcen und den Anforderungen der Umwelt betrachtet werden. Überschreiten die Umweltanforderungen die Verhaltenspotenziale des Individuums, kann es zu Überforderung kommen. Verdeutlichen lässt sich diese Perspektive durch genaue Betrachtung von Verkehrsunfällen unter Beteiligung älterer Kraftfahrer: So spiegeln die aktuellen Unfallstatistiken aus 2008 wider, dass ein großer Teil der Unfälle von Kraftfahrern im Alter über 65 Jahren auf sogenanntes Fehlverhalten in Knoten, wie z.B. Fehler beim Abbiegen, Ein- und Ausfahren in Kreuzungen und Vorfahrtbeachtung, zurückzuführen sind. Diese im Vergleich zu jüngeren Fahrern häufigere Verwicklung Älterer in Unfälle dieser Art legt nahe, dass es in genau diesen Situationen zu einem Ungleichgewicht zwischen individuell verfügbaren Ressourcen und den Anforderungen der Verkehrsumwelt kommt. Beispielsweise könnten in diesen Situationen Beeinträchtigungen der visuellen Wahrnehmungsfähigkeit, verlangsamte Reaktionszeiten oder auch Einschränkungen der Bewegungsausführung zu einer zu langsamen oder auch falschen Entscheidungsfindung oder Handlungsausführung im Straßenverkehr führen. Dieser Perspektive folgend können Maßnahmen zur Erhöhung der Verkehrssicherheit älterer Kraftfahrer zum einen auf Seiten des Individuums ansetzen und dazu beitragen, die Kompetenzen des älteren Kraftfahrers zu erhöhen, zum anderen Bezug auf den Kontext nehmen, indem durch Anpassungen der Bedingungen der Verkehrsumwelt zur Sicherheit " nicht nur " älterer Kraftfahrer beigetragen wird. Personenzentrierte Ansätze zielen dabei auf die Ausschöpfung der individuellen Potenziale zur Aufrechterhaltung, Verbesserung oder auch Wiederherstellung einer sicheren Verkehrsteilnahme bis ins hohe Lebensalter. Diese Ansätze umfassen Trainings- und Rehabilitationsprogramme der Fahrkompetenz gleichermaßen wie verkehrspädagogische Programme, mediale Informationskampagnen oder auch Beratungsmaßnahmen und Screening-Tests. Eine Schlüsselposition kann in diesem Kontext dem (Haus)-Arzt als Experten hinsichtlich Konstitution und Lebensverhältnissen seines Patienten und Vertrauensperson zukommen. In der Regel passen ältere Kraftfahrer ihr Fahrverhalten ihren individuell verfügbaren Kompetenzen an. Auf diese Weise können altersbegleitende oder auch mit Erkrankungen oder Medikamenteneinnahmen einhergehende Veränderungen der körperlichen oder geistigen Leistungsfähigkeit zumeist erfolgreich kompensiert werden. Personenzentrierten Ansätzen kommt jedoch eine besondere Relevanz für den kleinen Anteil älterer Fahrer zu, welche keine oder nur unzureichende Kompensation aufweisen. Kontextorientierte Ansätze beziehen sich auf Maßnahmen, welche eine möglichst optimale Gestaltung der Bedingungen der Verkehrsumwelt auf die Bedürfnisse und Anforderungen älterer Kraftfahrer herbeiführen sollen. Maßnahmen dieser Art zielen zum Beispiel auf eine Entschleunigung des Straßenverkehrs durch Geschwindigkeitsbegrenzungen oder auch bauliche Maßnahmen. Auch die Potenziale moderner Fahrzeugtechnik werden unter dieser Perspektive zur Erhöhung der Verkehrssicherheit älterer Fahrer nutzbar. So können Fahrerassistenz- oder Fahrerinformationssysteme den älteren Fahrer in komplexen Situationen unterstützen. Dabei ist der Nutzen für die Verkehrssicherheit jedoch stark von der Handhabbarkeit und Bedienqualität der technischen Hilfsmittel abhängig. Technologien, welche die Komplexität der Fahrzeugbedienung erheblich erhöhen oder die Aufmerksamkeit vom Straßenverkehr ablenken, können ggf. auch zu einer weiteren Diskrepanz zwischen Anforderungssituation und verfügbaren Kompetenzen beitragen. Neben diesen eher auf die individuelle Verkehrsteilnahme als Autofahrer bezogenen Maßnahmen sind weitere wichtige kontextorientierte Ansatzpunkte in alternativen Mobilitätsvarianten zum Auto, wie in der Verbesserung der Attraktivität von Angeboten des ÖPNV oder auch den Bedingungen für Fußgänger und Radfahrer, zu finden. In diesem Sinne erscheint ein mehrdimensionaler Ansatz für die Gestaltung von Maßnahmen zur Erhöhung der Verkehrssicherheit älterer Kraftfahrer am erfolgversprechendsten. Interventionsansätze sollten sich gegenseitig ergänzen und möglichst sowohl die Ressourcen auf Seiten des älteren Menschen selbst als auch der Umwelt umfassen.
A set of recommendations for pan-European transparent and independent road accident investigations has been developed by the SafetyNet project. The aim of these recommendations is to pave the way for future EU scale accident investigation activities by setting out the necessary steps for establishing safety oriented road accident investigations in Member States. This can be seen as the start of the process for establishing road accident investigations throughout Europe which operate according to a common methodology. The recommendations propose a European Safety Oriented Road Accident Investigation Programme which sets out the procedures that need to be put in place to investigate a sample of every day road accidents. They address four sets of issues; institutional addressing the characteristics of the programme; operational describing the conditions under which data isrncollected; data storage and protection; and reports, countermeasures and the dissemination of data.rn
The national accident statistics demonstrate that the situation of passenger car side impacts is dominated by car to car accidents. Car side to pole impacts are relatively infrequent events. However the importance of car side to pole impacts is significantly increasing with fatal and seriously injured occupants. For the present study the German in-depth database GIDAS (German In-Depth-Accident Study) and the UK based database CCIS (Co-operative Crash Injury Study) were used. Two approaches were undertaken to better understand the scenario of car to pole impacts. The first part is a statistical analysis of passenger car side to pole impacts to describe the characteristics and their importance relevant to other types of impact and to get further knowledge about the main factors influencing the accident outcome. The second part contains a case by case review on passenger cars first registered 1998 onwards to further investigate this type of impact including regression analysis to assess the relationship between injury severity and pole impact relevant factors.
The role of a national motor vehicle crash causation study-style data set in rollover data analysis
(2010)
On 1 January 2005, The National Highway Traffic Safety Administration, an agency of the United States Department of Transportation, implemented a new data collection strategy designed to assess crash avoidance technologies and report associated behavioral inputs and outcomes. The original goal was a six-year program, however, during the shortened data collection period; it proved a valuable resource for understanding a precrash environment previously obscured by forensic case investigation. Another unintended consequence was an overlap with infrastructure, roadway geometry, and design with the occupant and vehicle outcomes, by virtue of well-defined attributes. External to the collected data, supplementary information was extrapolated, by using manuals published in the United States, by the American Association of State Highway Transportation Officials and selected State Departments of Transportation, in conjunction with the National Motor Vehicle Crash Causation Study (NMVCCS). This provided a backdrop to the infrastructure framework of the rollover problem within which the occupant and vehicle outcomes were studied. If a NMVCCS-style data collection were to be implemented elsewhere, then complementary manuals produced by federal transportation officials might be consulted producing similar relationships. The current study uses NMVCCS data to describe vehicles travelling through diverse design geometries and the outcome for occupants involved in crashes within that system. Codified and extrapolated data form the basis for assessing NMVCCS and its value to the transportation safety community, as the protocols are applicable universally. The benefit in continuing a NMVCCS-style study is noted, as the interaction of roadway infrastructure and occupant protection agencies might find paths to better work together in solving the complex rollover problem using a common data-driven approach.
Verkehrsunfallopfer, die beim Unfall überrollt werden, erleiden fast immer tödliche Verletzungen. Im innerstädtischen Bereich ereignen sich diese Unfälle mehrheitlich im niedrigen Geschwindigkeitsbereich. Die Frage der Vermeidbarkeit des Unfalls wird daher sehr oft seitens der Ermittlungsbehörde an die Sachverständigen gestellt. Im Rahmen der Unfallrekonstruktion spielt der Reifenprofilabdruck am Leichnam eine wichtige Rolle. Er belegt nicht nur den Überrollungsvorgang selbst, sondern erlaubt auch die Identifikation der Überrollungsrichtung und -region, aber auch des in Frage kommenden Reifens. Bei der retrospektiven Analyse von 120 Überrollungsfällen in Berlin (Fußgänger, Radfahrer und Kraftradfahrer) aus den letzten 23 Jahren wurde untersucht, wie verlässlich dieses Merkmal ist, wie oft und wo man es findet und von welchen Faktoren seine Entstehung beeinflusst wird.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.
Das Fahrverhalten ändert sich mit zunehmendem Alter. Damit ändern sich auch die Risiken. Neben den jungen Fahranfängern im Alter von 18 bis etwa 25 Jahren stellen Fahrer über 75 Jahre eine besondere Problemgruppe dar. Mit zunehmender Zahl alter Fahrer (demographische Entwicklung plus Zunahme der Fahrerlaubnisinhaber in dieser Altersgruppe) besteht hier in naher Zukunft akuter Handlungsbedarf. Ansatzpunkte gibt es im gesamten Mensch-Maschine-Umwelt-System. Fahrzeuge müssen vermehrt im Hinblick auf alte Fahrer konstruiert und optimiert werden. Die Infrastruktur muss den Bedürfnissen einer eindeutigen Verkehrsführung angepasst werden. Aber nur, wenn der Mensch selbst geeignet ist, als Fahrer am Straßenverkehr teilzunehmen, ist ein Gewinn bei der Verkehrssicherheit zu erwarten. Dies muss gewährleistet werden. Wichtig ist, dass die Problematik der alten Fahrer als solche erkannt wird und schnell eine tragfähige Lösung für die Zukunft gefunden wird.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
The frontal crash is still an important contributor to deaths and serious injured resulting from road accidents in Europe. As the Hybrid-III dummy used in crash tests is over two decades old, the European Enhanced Vehicle-safety Committee is studying the potential for a new test device. Key is the availability of a well-defined set of requirements that identifies the minimum level of biofidelity required for an advanced frontal dummy. In this paper, a complete set of frontal impact biofidelity requirements, consisting of references , description of test conditions and corridors, is presented.
This paper gives an overview of the in-depth crash investigation activity conducted by the Centre for Automotive Safety Research (CASR) at the University of Adelaide, in South Australia. Recent changes in method include: an expansion in on-call hours for the crash investigation team, providing the option of a phone interview for crash participants to discuss the crash, and downloading objective crash data from vehicle airbag control modules. These changes have resulted in: increased representativeness of crashes by hour of day; a decrease in the over-representation of fatal crashes in our sample; an increase in the proportion of crashes that involved a pedestrian, bicycle or scooter (moped); an increase in the proportion of crash participants consenting to an interview; and an increase in the objective data available, through airbag control module downloads. Our in-depth crash investigations enabled research into road departures that found barriers were a more feasible solution than clear zones for eliminating serious and fatal injury resulting from run off road crashes.
Die UNECE Regelung R58 regelt die Beschaffenheit und die Installation von Heckunterfahrschutzsystemen an schweren Güterkraftfahrzeugen, deren Ziel die Verbesserung der Kompabilität zwischen Pkw-Frontstrukturen und Lkw-Hecks ist. Dennoch verunglücken laut amtlicher Unfallstatistik allein in Deutschland rund 30 Pkw-Insassen in Heckauffahrunfällen auf Lkw tödlich, da diese Vorrichtungen hinsichtlich Einbauhöhe und Steifigkeit den Anforderungen des realen Unfallgeschehens nicht genügen. Das Ziel dieser Studie ist eine quantitative Abschätzung der möglichen Reduzierung der Verletzungsschwere mit Hilfe eines statistischen Modells, die durch eine Anpassung der geltenden Bestimmungen und die damit verbundenen technischen Veränderungen des bereits vorgeschriebenen Heckunterfahrschutzes zu erreichen wäre. In einer Nutzen-Kosten-Analyse wird die Wirtschaftlichkeit dieser Modifizierungen mit einem idealen Notbremsassistenten verglichen. Die Untersuchung orientiert sich dabei an den aktuell in der UN-ECE WP29/GRSG in Genf diskutierten Vorschlägen zur Anpassung der ECE-R58. Das verwendete ordinale Probit-Modell stellt einen Zusammenhang zwischen der Verletzungsschwere im auffahrenden PKW und erklärenden Größen her, in diesem Fall der kinetischen Energie des unterfahrenden Pkws und der strukturellen lnteraktion zwischen Lkw-Heck und Pkw-Front. Diese Maßnahmen könnten demnach 53 - 78% der Getöteten sowie 27 - 49% der Schwerverletzten bei diesen Unfallkonstellationen reduzieren, was pro Jahr 20 Getöteten und 95 Schwerverletzten entsprechen würde. Somit würde eine Modifikation einer bestehenden passiven Schutzmaßnahme an jährlich 100.000 neuzugelassenen Lkw und Anhängern bereits 20 Getötete adressieren. Im Vergleich dazu müssten jährlich 3 Millionen Pkw mit zusätzlicher Sensorik und Aktuatorik für einen idealen Notbremsassistenten ausgestattet werden, um im Idealfall alle Heckauffahrunfälle von Pkw auf andere Pkw oder Lkw und damit 53 Getötete zu vermeiden. Daher fällt auch das Nutzen-Kosten-Verhältnis deutlich zugunsten des verbesserten Heckunterfahrschutzes aus.
An analysis of NASS and FARS was conducted to determine crash conditions that involved injuries that are not currently being directly addressed by vehicle safety standards or by consumer information test protocols. Analysis of both field data and US NCAP tests were conducted to determine the relative safety provided by seating position and by vehicle model year. Opportunities for improvements were determined by crash categories with large populations of injuries that were not addressed by safety tests or smaller numbers that were increasing in frequency. Areas of opportunities include improved occupant restrain in rollovers, improved frontal protection for rear seat occupants and improved fire prevention in frontal and rollover crashes.
One of the major problems of road safety in Europe is the powered two wheelers accidents. One of the European countries with one of the highest rates is Portugal where in 2006, mopeds and motorcycles fatalities represented 27% of all road users deaths. In this work, a deep analysis and overview of the current state of mopeds and motorcycles accidents for the 2004-2006 period is presented. Within this period 830 PTW occupants die, 2958 have been severely injured and 25000 suffer slight injuries. A detailed analysis of the conditions of these accidents has been carried out, using the data of the national accident database. This analysis provides global information, about geographic environmental conditions, driver- characteristics among others. From this data detailed information is obtained allowing to know when, where and who. In order to answer the question why more a widely collection of data has been collect for 70 accidents. The data has been collected using OECD methodology. For these accidents a detailed reconstruction has been carried out, what is especially important for fatal accidents where for instance speed in an important factor. From these collection and analysis of data a wider overview of facts and measures are extracted. Among them, some are emphasized such as that the quality and non-use of helmets plays an important role in severe and fatal accidents especially for accidents involving moped vehicles, or speed is the most important factor in fatal accidents involving motorcycles. Concerning motorcycle accident reconstruction, different tools can be used depending of the accident scenario and complexity. For simple cases, with specific characteristics, analytical formulation based in vehicle crash dynamics can be use in order to determine the impact speed of the vehicles impact, analysing the skid marks, deformations, victims rest position and considering parameters (EES, vehicle deceleration, etc). Aspects such as the energy absorption capability of motorcycles are also discussed. In the general cases the accident reconstruction software Pc-Crash has been used for the reconstruction of the accident. In very complex cases, has for instance the impact between motorcyclist and barriers, Madymo software is used especially to determine speed from injuries. An example of the impact of a motorcyclist and a motorcyclist-friendly barrier is present to illustrate the benefits and limitations of such systems.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
Accidents involving two wheels vehicles represent one of the more important types of accidents in Europe. These accidents are usually not easy to reconstruct specially for the analysis of the injuries and its correlation with accident dynamics and evidences. Different methodologies are applied in this work for the reconstruction of two wheeler accidents, especially accident involving motorcycles. From the typologies of road evidences like skid marks, to the use of Pc-Crash and the use of Madymo models, different reconstruction of real accidents are presented. One of the questions that sometimes arise for legal purposes when some type of head injuries arise is if the occupant was wearing or not a helmet. The correlation of head injuries with the use of the helmet is a very important issue, therefore an important legal aspect. One of the key questions for the reconstructions that is difficult to analyze, is if the vehicle occupant, was or not, wearing the helmet. Based on the previously collected information, a generic model of a helmet was developed on CAD 3D, followed by its conversion into finite elements, all in order to perform impact tests using the Madymo software that would help improve the helmet- safety, but that also can be used as a tool in accident reconstruction.
Portugal has the highest rate of road fatalities in Europe (2002 and for Eur-15 - CARE database). For this highest rate, the accidents involving pedestrians and motorcycle occupants have a higher contribution than the European average. In the last years, especially accidents involving motorcycles have been investigated and currently two different projects are being carried out, one related with motorcycles accidents and the other with pedestrian accidents. In these projects, countermeasures among others to reduce the fatalities between these two types of road users are being studied. These accidents are investigated with the commercial accident reconstruction software PCCRASH but also new methodologies based on multibody dynamics are in development in order to more accurately study these two types of accidents. In this paper, the methodologies in use for accident reconstruction and new methodologies in development are presented. Speeding his found to be one of the major causes of road fatalities for pedestrians and motorcycle occupants. In the case of motorcycle accidents, these involve mainly young drivers. Aspects as social behavior are also important to understand the causes of some of these accidents. Some examples of accidents occurring in Portugal, involving especially motorcycles and pedestrians are presented and discussed.
Internationally, the need is expressed for harmonized traffic accident data collection (PSN, PENDANT, etc.). Together with this effort of harmonization, traffic accident investigation moves more and more in the direction of accident causation. As current methods only partly address these needs, a new method was set up. The main characteristics of this method are: • Accident/injury causation (associated) factors can objectively be identified and quantified, by comparison with exposure information from a normal population. • All relevant accident and exposure data can be included: human-, vehicle-, and environmental related data for the pre-crash, crash and postcrash situation (the so-called Haddon matrix). The level of detail can be chosen depending on interest and/or budget, which makes the method very flexible. In this paper the accident collection and control group method are presented, including some of the achieved results from a pilot study on 30 truck accidents and 30 control locations. The data were analyzed by using cross-tabulations and classification-tree analysis. The method proved useful for the identification of statistically significant causational aspects.
Validation of human pedestrian models using laboratory data as well as accident reconstruction
(2007)
Human pedestrian models have been developed and improved continually. This paper shows the latest stage in development and validation of the multibody pedestrian model released with MADYMO. The biofidelity of the multibody pedestrian model has been verified using a range of full pedestrian-vehicle impact tests with a large range in body sizes (16 male, 2 female, standing height 160-192cm, weight 53.5-90kg). The simulation results were objectively correlated to experimental data. Overall, the model predicted the measured response well. In particular the head impact locations were accurately predicted, indicated by global correlation scores over 90%. The correlation score for the bumper forces and accelerations of various body parts was lower (47-64%), which was largely attributed to the limited information available on the vehicle contact characteristics (stiffness, damping, deformation). Also, the effects of the large range in published leg fracture tolerances on the predicted risk to leg fracture by the pedestrian model were evaluated and compared with experimental results. The validated mid-size male model was scaled to a range of body sizes, including children and a female. Typical applications for the pedestrian models are trend studies to evaluate vehicle front ends and accident reconstructions. Results obtained in several studies show that the pedestrian models match pedestrian throw distances and impact locations observed in real accidents. Larger sets of well documented cases can be used to further validate the models especially for specific populations as for instance children. In addition, these cases will be needed to evaluate the injury predictive capability of human models. Ongoing developments include a so-called facet pedestrian model with a more accurate geometry description and a more humanlike spine and neck and a full FE model allowing more detailed injury analysis.
Injury severity of e.g. pedestrians or bikers after crashes with cars that are reversing is almost unknown. However, crash victims of these injuries can frequently be seen in emergency departments and account for a large amount of patients every year. The objective of this study is to analyze injury severity of patients that were crashed into by reversing cars. The Hannover Medical School local accident research unit prospectively documented 43,000 road traffic accidents including 234 crashes involving reversing cars. Injury severity including the abbreviated injury scale (AIS) and the maximum abbreviated injury scale (MAIS) was analyzed as well as the location of the accident. As a result 234 accidents were included into this study. Pedestrians were injured in 141 crashes followed by 70 accidents involving bikers. The mean age of all crash victims was 57 -± 23 years. Most injuries took place on straight stretches (n = 81) as well as parking areas (n = 59), entries (n = 36) or crossroads (n = 24). The AIS of the lower extremities was highest followed by the upper extremities. The AIS of the neck was lowest. The mean MAIS was 1.3 -± 0.6. The paper concludes that the lower extremities show the highest risk to become injured during accidents with reversing cars. However, the risk of severe injuries is likely low.
While cyclists and pedestrians are known to be at significant risk for severe injuries when exposed to road traffic accidents (RTAs) involving trucks, little is known about RTA injury risk for truck drivers. The objective of this study is to analyze the injury severity in truck drivers following RTAs. Between 1999 and 2008 the Hannover Medical School Accident Research Unit prospectively documented 43,000 RTAs involving 582 trucks. Injury severity including the abbreviated injury scale (AIS) and the maximum abbreviated injury scale (MAIS) were analyzed. Technical parameters (e.g. delta-v, direction of impact), the location of accident, and its dependency on the road type were also taken into consideration. The results show that the safety of truck drivers is assured by their vehicles, the consequence being that the risk of becoming injured is likely to be low. However, the legs especially are at high risk for severe injuries during RTAs. This probability increases in the instance of a collision with another truck. Nevertheless, in RTAs involving trucks and regular passenger vehicles, the other party is in higher risk of injury.
In North America, frontal crash tests in both the regulatory environment and consumer-based safety rating schemes have historically been based on full-width and moderate-overlap (40%) vehicle to barrier impacts. The combination of improved seat-belt technologies, notably belt tensioning and load limiting systems, together with advanced airbags, has proven very effective in providing occupant protection in these crash modes. Recently, however, concern has been raised over the contribution of narrower frontal impacts, involving primarily the vehicle corners, to the incidence of fatality and serious injury as a result of the potential for increased occupant compartment intrusion and performance limitations of current restraint systems. Drawing on data documented in the National Automotive Sampling System (NASS)/ Crashworthiness Data System (CDS) for calendar years 1999 to 2012, the present study examines the characteristics of existing and proposed corner crash test configurations, and the nature of real-world collisions that approximate the test environments. In this analysis, particular emphasis is placed on crash pulse information extracted from vehicle-based event data recorders (EDR's).
The National Roads Authority in Ireland is responsible for planning and supervision of construction and maintenance works on the National Road network. Its primary function is "to secure the provision of a safe and efficient network of national roads". The population of Ireland has grown rapidly from 3.5 million to 4 million within the past 10 years, and vehicle ownership has also risen rapidly to 2 million vehicles, with 2.2 million drivers. Collisions rates in Ireland are at approximately 1.5 collisions per 1,000 population (in 2002), and 8.4 deaths per 1,000,000 population (in 2003). This ranked 8th out of the 15 countries in the European Union at the time. Ireland- current Road Safety Strategy includes Engineering Targets. These are to complete construction of certain lengths of new motorway, dual carriageway and 2+1 highway, to implement a certain number of accident remedial and traffic calming schemes, and to implement road safety audit on all new schemes. The accident remedial schemes, traffic calming schemes, and road safety audit are all the responsibility of the Road Safety section of NRA. The road safety programme of the NRA is divided into four main areas; a) accident remedial measures at individual sites, b) accident remedial treatment of entire routes, c) traffic calming of towns and villages on main roads, d) road safety audit. Examples of these measures are described. Evaluation of past programmes of single site accident remedial measures show a reduction in collision occurrence at these sites, but the effectiveness and the economic rate of return is decreasing over successive programmes. A similar programme has now been adopted on the rest of the country- road network, on regional and local roads. The programme of remedial treatment of entire routes has only recently started and has not been evaluated. Evaluation of the first programme of traffic calming of towns and villages shows an overall decrease in collisions and their severity, and a small reduction in speed. Road Safety Audit, examining new schemes a number of times during design and after construction, has been standard procedure on the national road network for nearly 6 years. An evaluation is currently underway.
Impact severity is a fundamental measure for all in-depth crash investigation projects. One methodology used in the UK is based on the US Calspan software package CRASH3. The UK- in-depth crash investigation studies routinely use AiDamage3 a software package which is based on an updated version of the original CRASH3 algorithm, including enhancements to the vehicle stiffness coefficients. Real world accident-damaged vehicles are measured and their crush is correlated with a library of stiffness coefficients. These measurements are then used, along with other parameters, to calculate the crash energy and equivalent changes of velocity of the vehicles (delta-v), which is a measure of the impact severity. UK in-depth accident studies routinely validate the crash severity methodologies applied as the vehicle fleet changes. This is achieved by analysing crash test data and using the appropriate residual crush damage and other inputs to AiDamage3 and checking the program- outputs with the known crash severity parameters. This procedure checks, at least in part, the default stiffness values in the data libraries and the reconstruction methods used.
Traffic accidents were ranked the third among the major causes of death in Thailand. About 13,438 deaths and the death rate from traffic accident was 21.5 per 100,000 of population in 2002. The deaths and death rate varied upon the economic situation. After the economic crisis, traffic accidents were increased as well as the period of the bubble economy. In the Central region of Thailand numbers of road traffic crashes were lower than Bangkok Metropolis, but the highest in the number of deaths, death rate and serious injuries in 2002. Men aged 15"29 years old had higher numbers of deaths than men in other age groups and higher than women. Deaths and injuries from road traffic crashes were the highest in April and January, because there was a long weekend in those months. About 80 percent of road traffic crashes were caused by private car and motorcycle. In 2000 about 51 percent of traffic accidents took place on the straight way, followed by the junction and curves. In 2002, about 97 percent of road traffic crashes were caused by human factors including improper passing, speeding and disregarding to traffic signal, however, the identification of causes of traffic accident needed to improve. Drunk driving, disregarding on safety equipment usage, inefficiency of law enforcement and discontinuing of road safety programs were the deepest causes of traffic accidents. Research based information, a broad coalition of stakeholder and urban planning policy were needed to incorporate for a comprehensive road safety policy formulation and actions.
Pedestrian and cyclist are the most vulnerable road users in traffic crashes. One important aspect of this study was the comparable analysis of the exact impact configuration and the resulting injury patterns of pedestrians and cyclists in view of epidemiology. The secondary aim was assessment of head injury risks and kinematics of adult pedestrian and cyclists in primary and secondary impacts and to correlate the injuries related to physical parameters like HIC value, 3ms linear acceleration, and discuss the technical parameter with injuries observed in real-world accidents based documented real accidents of GIDAS and explains the head injuries by simulated load and impact conditions based on PC-Crash and MADYMO. A subsample of n=402 pedestrians and n=940 bicyclists from GIDAS database, Germany was used for preselection, from which 22 pedestrian and 18 cyclist accidents were selected for reconstruction by initially using PC-Crash to calculate impact conditions, such as vehicle impact velocity, vehicle kinematic sequence and throw out distance. The impact conditions then were employed to identify the initial conditions in simulation of MADYMO reconstruction. The results show that cyclists always suffer lower injury outcomes for the same accident severity. Differences in HIC, head relative impact velocity, 3ms linear contiguous acceleration, maximum angular velocity and acceleration, contact force, throwing distance and head contact timing are shown. The differences of landing conditions in secondary impacts of pedestrians and cyclists are also identified. Injury risk curves were generated by logistic regression model for each predicting physical parameters.
Mechanical properties of tibial bone at compressive strain rates of 50-200 s-1 are obtained through Split Hopkinson pressure bar. Cylindrical specimens of 12-15 mm diameter and 2-5 mm thickness were used. The Young- moduli are calculated from linear portion of stress-strain curves. For both cortical and cancellous part of the bones, the Young- modulus was found to increase with the increasing strain rates. Also for both cancellous and cortical bones the Young- modulus increases consistently with increase in densities.
Before 2002, France was in the queue of Europeans countries in terms of road safety results because of the low density of population and the faulty behaviour of French due itself to a very low level of traffic law enforcement Even if there were signs of the change of mind in France towards road safety before, the turning point was in summer 2002, when the President declared road safety as a priority work during his mandate. The more symbolic measure was the decision to settle an automatic speed control system (700 fixed and 300 mobile). Over three years, the average speed on French roads decreased by 5 km/h and the number of fatalities on road turned down from an average of 8000 deaths per year to 5 300, which represents a decrease of more than 34 %. For the next months, we anticipate that, as many drivers have kept loosing points on their driving licence through light speed violations, this will lead drivers to check their speed and the speed limits more systematically as loosing points on one's driving license has longer time effects than paying a fine. Consequently, we expect a decrease of 10 % to 15% of fatalities in 2006, which is a very good result if we compare with the trend of the last twenty five years (about 2,3 %). The reverse effect of this system that lies on the changes of behaviour of the majority is that, there is more and more discontent against the system taking into account that automatic speed control system allows only a minor tolerance above limits and that local speed limits are not always adapted to local infrastructure and traffic conditions. Another weakness of the system is that motorcyclists are too rarely caught by the system; the system is being gradually improved by placing the new speed cameras in position of taking photographs of the back of the vehicle. But this would not be sufficient to reduce the speed of motorcyclists that are a very high risk group (16% of fatalities for 0,8 % of traffic) For alcohol, there is no easy route for progress: all what is done nowadays is toward festive impaired driving (through designating sober drivers or mass alcohol preventive screenings) although there is not enough done towards chronic alcoholic driving.
An eCall device has been mounted on some vehicles in France since 2003. It is an integrated car radio/GSM/GPS system that can be used with a SIM card. When an accident occurs, a call can be sent manually or automatically made to a telephone call centre. Knowing the geographic location, the vehicle identity and the possibility of a direct communication with the people involved enables the nearest emergency services to be called out. In this context, the LAB / CEESAR have set up a study aimed at evaluating the effectiveness of this system. The purpose of this paper is to detail the E-call system evaluation method of effectiveness used and give a global synthesis of the results.
This work aims at bringing evidence for mass incompatibility in frontal impact for cars built according to the UNECE R94 regulation. French national injury accidents database census for years 2005 to 2008 were used for the analysis. The heterogeneity of frontal self-protection among cars of different masses is investigated, as well as the partner protection parameter offered by these cars. The last part of the analysis deals with the estimation of the benefit, in terms of fatal and severe injuries avoided, if crashworthiness was harmonized for the whole fleet of vehicle. This calculation is done for France and is extended to all Europe.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
Among European Countries, Spain first issued a Standard, UNE 135900:2005, further updated in 2008, that deals with homologation and effectiveness evaluation of road restraint systems components designed to reduce harm for bikers impacting on them. An in depth analysis and critical review of this standard is reported in this paper. Beside a close examination of the standard requirements, numerical models of the crash test stated by the standard have been set up and simulated to study the effects of slight speed and approach angle variations on test results, remaining within tolerance gaps allowed by the standard. Model were validated against experimental data. Together with the expected increasing severity of the impact according with speed, a strong influence of approach angle on injury parameters was found. Possible improvements to the norm, in order to make it more robust, are suggested.
In-depth accident investigation offers many advantages for the analysis and comprehension of crash mechanisms. IFSTTAR makes such investigations since 1992 without interruption. The corresponding database contains more than 1200 accident case studies. Currently, in-depth accident investigation is one of the best ways to determine the speed or cars involved in accidents. This paper first presents the methods used for accident investigation and for accident kinematic reconstruction. Then, in order to illustrate the interest and possible applications of such accident data, it shows some results from a recent study based on the IFSTTAR in-depth accident study programme (IDAS) and dealing with the link between travelling speed and accident risk.
Mit dem Beitrag soll ein Überblick zum aktuellen Bearbeitungsstand der ZTV Ew-StB vermittelt werden. Insbesondere soll auf Neuerungen und Veränderungen hingewiesen und diese inhaltlich kurz beleuchtet werden. Hervorzuheben ist, dass das Regelwerk um die grabenlose Kanalsanierung erweitert wurde und zulässige Abweichungen beim Bau von Entwässerungseinrichtungen geändert wurden. Nach ca. 4 Jahren ist die Überarbeitung und Abstimmung nunmehr weitgehend abgeschlossen.
Supervision of the safety performance in public transport is one of the main tasks of the Federal Office of Transport (FOT) in Switzerland. Recently a three level system of safety indicators has been defined to cover all means of Swiss public transport. The safety indicators are fed by the FOT incident database since the year 2000. In cooperation with the Institute for Traffic Safety and Automation Engineering (iVA) at TU Braunschweig, Germany, FOT is developing a suitable methodology for the definition and evaluation of the safety targets in Swiss public transport. The methodology is applied for evaluation of safety indicators on a country level and for single transport companies. In a new approach the abovementioned methodology is applied to car incident data to develop an indicator based cross-modal safety measure.
The average CO2 concentrations relevant to a motorcyclist wearing an integral helmet were measured twenty years ago and found to be alarmingly high. The present study examined gas concentrations typically inhaled by a motorcyclist. Average concentrations of CO2 for persons (n=4) wearing integral motorcycle helmets were measured in the laboratory and the field to facilitate comparison to previous work, and similarly high average concentrations were found: above 2% when stationary, well below 1% for speeds of 50km/h or more. Detailed measurements of the time-dependent CO2 concentrations during normal inhalation showed levels of about half of the corresponding average concentrations, including 1% at standstill, though higher concentrations (4% or more) are inhaled at the beginning of each breath. Opening the visor at standstill lowered the average inhaled concentration only to about 0.8%. The oxygen deficiency is equal to the CO2 concentration, and could also contribute negatively to motorcyclist cognitive abilities.
Aus der Zusammenschau der gegenwärtigen Studienliteratur sowie den Ergebnissen der vorliegenden Untersuchung lässt sich ableiten, dass die Fahrtüchtigkeit eines unter Reboxetin oder Mirtazapin zum Teil remittierten Patienten als günstiger einzuschätzen ist als die eines unbehandelten depressiven Patienten. Die Bewertung eines Antidepressivums kann, wie die vorliegenden Ergebnisse zeigen, nicht vorrangig auf Basis der sedierenden Eigenschaften eines Präparats vorgenommen werden. Die experimentellen Daten belegen, dass neben der Verordnungsdauer und den damit zu erwartenden Adaptationsmechanismen auch der Einnahmezeitpunkt entscheidend bei der Bewertung der Substanz in Bezug auf die Verkehrssicherheit ist. Die vorliegenden Ergebnisse haben darüber hinaus wichtige Implikationen für die Einschätzung des Risikopotenzials neuerer selektiver Antidepressiva im Rahmen gesetzlicher Verordnungen. Bei der Bewertung des Gefährdungspotenzials dieser Substanzgruppe scheinen weit weniger die pharmakologischen Effekte als vielmehr morbogene Faktoren zu berücksichtigen zu sein. Die meisten der derzeit erhältlichen Antidepressiva sind weitgehend vergleichbar in Bezug auf ihre therapeutische Effektivität, sodass bei der Auswahl der Medikamente in erster Linie das Nebenwirkungsprofil ausschlaggebend ist.
Ziel der durchgeführten Untersuchungen war die Analyse der Straßenverkehrsdelikte im Wiederholungsfall unter Alkoholeinfluss. Im Untersuchungszeitraum wurden 29.939 Polizeiprotokolle aus Vorpommern und Süd-Mecklenburg ausgewertet. Für den Zeitraum 1998 - 2002 fanden sich 11 Prozent Mehrfachdelikte. Mit circa 98 Prozent Beteiligung sind Männer die am häufigsten als Mehrfachdelinquenten auftretende Gruppe. Im Vergleich mit anderen Jahrgängen sind Täter im Alter von 18 - 25 Jahren auffallend häufig vertreten. Die festgestellten Blutalkoholkonzentrationen in Kombination mit einer Straftat im Straßenverkehr bleiben über die einzelnen Jahre des Erhebungszeitraumes hinweg konstant im Bereich der absoluten Fahruntauglichkeit bei einem Mittelwert von 1,85 Promille. Die Blutalkoholkonzentrationen der Rückfalltäter steigen mit zunehmendem Alter. Mit dem Anstieg der Blutalkoholkonzentration steigt auch die Deliktschwere. Circa 38 Prozent der Rückfalltaten im Straßenverkehrsbereich wurden mit einer Blutalkoholkonzentration über 2,0 Promille begangen. Dabei ist der Anteil derjenigen gering, die alkoholisiert am Straßenverkehr teilnehmen und dann allein einen Unfall verursachen (11,2 Prozent). Die meisten Wiederholungstäter fielen zweimal auf, die häufigste Anzahl war 13 bei einer Person.
Es besteht Einigkeit darüber, dass Blutalkoholkonzentrationen (BAK) ab 0,30 Promille experimentell nachweisbare Beeinträchtigungen der Fahrtüchtigkeit hervorrufen. Die vorliegende Arbeit soll fundierte Aussagen über das Ausmaß und die Qualität kognitiver Veränderungen bei niedrigen BAK (um 0,30 Promille) ermöglichen. Es wurden in einer doppelblinden, placebokontrollierten Studie 16 gesunde männliche Probanden untersucht. Die BAK wurden während der Versuche auf etwa 0,30 Promille eingestellt. Es wurden mittels umfangreicher neuropsychologischer Tests untersucht: das allgemeine Intelligenzniveau, subjektive Beeinträchtigungen, mögliche depressive Symptome, die allgemeine Leistungsfähigkeit, die Vigilanz, die geteilte Aufmerksamkeit, die Reaktionszeit und die Gedächtnisleistungen. Die biostatistische Auswertung erfolgte im 2-Perioden-Crossover-Design. Zusammenfassend zeigen die vorliegenden Ergebnisse, dass bereits bei BAK von etwa 0,30 Promille vor allem kognitive Funktionen, die insbesondere auf die Wahrnehmung und die Verarbeitung visueller Informationen angewiesen sind, vor allem je komplexer und zeitkritischer eine Aufgabe wird, wie etwa die Beherrschung einer kritischen Situation im Straßenverkehr, relevant beeinträchtigt sind.
Die EU hat für die Verkehrssicherheit in Europa ein anspruchsvolles Ziel vorgegeben: Bis 2010 soll die Anzahl der im Straßenverkehr Getöteten gegenüber 2000 halbiert werden. Für Deutschland kann eine erfolgreiche Zwischenbilanz gezogen werden: In den letzten 5 Jahren nahm trotz Vergrößerung des Kraftfahrzeugbestandes um 6% die Anzahl der Verkehrstoten um 29% ab, in den vergangenen 10 Jahren ist ein Rückgang um 43% zu verzeichnen. Diese im internationalen Vergleich überdurchschnittlichen Erfolge sind nicht zuletzt auch auf Fortschritte in der Fahrzeugtechnik zurückzuführen, wobei die zunehmende Verbreitung von Systemen der Aktiven Sicherheit wie ABS, BAS, ESP einen entscheidenden Anteil hat. Nach der deutlichen Reduzierung von Fahrunfällen durch ESP-® stehen nun die Auffahrunfälle im Fokus der Sicherheitsentwicklung von Mercedes-Benz. Das Paket aus verbessertem rückwärtigen Signalbild (Adaptives Bremslicht) und Brems-Assistent (BAS) wurde kürzlich durch radarbasierte Bremsassistenz ergänzt (BAS PLUS und PRE-SAFE-®-Bremse). Der Beitrag geht auf Funktion und Wirksamkeit der einzelnen Systeme ein und gibt einen Ausblick in die nähere Zukunft.
Das 10. Kolloquium "Straßenbetriebsdienst", das in zweijährigem Turnus von der Forschungsgesellschaft für Straßen- und Verkehrswesen in Zusammenarbeit mit dem Fachgebiet Straßenwesen der Technischen Universität Darmstadt veranstaltet wird, fand am 17. und 18. Oktober 2001 in Darmstadt statt. Über 250 Teilnehmer waren wiederum der Einladung gefolgt. Auf vielfachen Wunsch wurde erstmals eine kleine Begleitausstellung organisiert, die Highlights, nicht aber ein umfassendes Lieferprogramm zeigen sollte. Die insgesamt 17 Vorträge der Veranstaltung wurden in drei Themenblöcken präsentiert: Aktuelle Probleme des Straßenbetriebsdienstes, Techniken und Strategien für einen wirksamen Straßenwinterdienst und Umweltaspekte der betrieblichen Straßenunterhaltung. Die Vorträge haben auf breiter Linie erneut unter Beweis gestellt, dass auf allen Ebenen der Verwaltung, der Industrie und der wissenschaftlichen Forschung vielfältige Anstrengungen unternommen werden, das bereits erreichte, auch im internationalen Vergleich hohe Niveau des Straßenunterhaltungs- und Winterdienstes weiter zu verbessern. Die eingeleiteten Maßnahmen bedürfen jedoch der konsequenten Weiterverfolgung. Der abschließende Teil 2 enthält die Übersicht über die Themenblöcke Techniken und Strategien für einen wirksamen Straßenwinterdienst (3.) und Umweltaspekte der betrieblichen Straßenunterhaltung (4.) sowie ein Resümee (5.).
Es wird über die Fachvorträge des Kolloquiums "Straßenbetriebsdienst" informiert, das zum neunten Mal gemeinsam von der Forschungsgesellschaft für Straßen- und Verkehrswesen und dem Fachgebiet Straßenwesen der Technischen Universität Darmstadt im Oktober 1999 veranstaltet wurde. In kurzen Zusammenfassungen wird über die Vorträge der drei Themenblöcke "Aktuelle Probleme des Straßenbetriebsdienstes", "Umweltaspekte der betrieblichen Straßenunterhaltung" und "Techniken und Strategien für einen wirksamen Straßenwinterdienst" berichtet.
Das 11. Kolloquium Straßenbetriebsdienst der Forschungsgesellschaft für Straßen- und Verkehrswesen fand nach 10 Veranstaltungen in der Technischen Universität Darmstadt erstmals in der Universität (TH) Karlsruhe statt. Die Veranstaltung hatte erneut über 250 Zuhörer aus dem In- und Ausland nach Karlsruhe geführt. Ihnen wurde ein umfangreiches Vortragsprogramm mit insgesamt 17 Vorträgen angeboten, das alle wesentlichen Aspekte des Straßenbetriebsdienstes umfasste. Sie wurden in den Themenblöcken "Aktuelle Themen im Straßenbetriebsdienst", "Ergebnisse laufender und abgeschlossener Forschungsvorhaben", "Techniken und Strategien im Winterdienst und Umweltaspekte des Straßenbetriebsdienstes" präsentiert. Zum Rahmenprogramm der Veranstaltung gehörten eine Begleitausstellung, eine Werksbesichtigung und praktische Gerätevorführungen.
In Germany averagely two million traffic accidents happen each year and emergency medical services are called to more than 400 000 patients. Even though this number is decreasing continuously (due to improvements in the fields of vehicle safety, road construction, and accident prevention) every case is yet a challenge for the rescuers and requires improvements in emergency medicine as well. Especially during diagnostics right at the accident scene, there are only limited instruments available to gain the necessary knowledge of the injuries suffered, to come to essential decisions about treatment or transport. To provide an additional diagnostic aid by scouting and estimating the situation, a software-tool calculating the likeliness of the most frequent severe injuries (AIS 3-6) of front occupants in passenger cars has been developed to deliver this necessary information about particular accident scenarios. To achieve this, logistic likelihood functions have been calculated in a multivariate regression analysis analysing all AIS 3+ injuries in the GIDAS database of the years 1999-2006 that happened more than four times
Each year the traffic accident research teams in Dresden and Hanover provide an in-depth investigation of approximately two thousand accidents, aggregated in the GIDAS database. To accomplish a comprehensive review of each traffic accident recorded, a sensible and thorough encoding of suffered injuries is indispensable. The Abbreviated Injury Scale by AAAM offers a valuable and handy solution to achieve this goal. However, there were a few difficulties in the use of the AIS that came up in the past, which let to necessary improvements for the utilization of the AIS 2005 for GIDAS.
The purpose of this study was to analyse the actual injury situation of bicyclists regarding accidents involving more than one bicyclist. Bicyclists were included in a medical and technical analysis to create a basis for preventive measures and discovered repeating accident patterns and circumstances such as daytime, environment, helmet use rate. Technical and medical data were collected at the scene, shortly after accident. The population was compared focusing on bicycle versus bicycle accidents. Technical analysis included speed at crash, type of collision, impact angle, environment, used lane and relative velocity. Medical analysis included injury pattern and severity (AIS, ISS). Included were 578 injured bicyclists in 289 accidents from years 1999 to 2008, 61 percent were male (n=350) and 39 percent female (n=228). Sixty-seven percent ranged between 18 to 64 years of age, twelve percent each between 13 to 17 years of age and older than 65 years, eight percent between 6 to 12 years and one percent between 2 to 5 years.. Crashes took place in urban areas in 92 percent, in rural areas in 8 percent. Weather conditions were dry lanes in 97 percent and wet conditions in 3 percent. Eighty-three percent of all accidents happened during daytime, ten percent during night, and seven percent during dawn. The helmet use rate was only 7,5 percent in all involved bicyclists. The mean Maximum Abbreviated injury scale, Injury severity score was 1,31. Bicyclists are still minimally- or unprotected road users. The helmet use rate is unsatisfactorily low. The incidence of bicycle to bicycle crashes is high. Most of these accidents take place in urban areas. The level and pattern of injuries is moderate. Most of the more severe injuries occur to the head and could have been avoided by frequent helmet use.
Still correlated with high mortality rates in traffic accidents traumatic aortic ruptures were frequently detected in unprotected car occupants in the early years. This biomechanical analysis investigates the different kinds of injury mechanisms leading to traumatic aortic injuries in todays traffic accidents and how the way of traffic participation affects the frequency of those injuries over the years. Based on GIDAS reported traffic accidents from 1973 to 2014 are analyzed. Results show that traumatic aortic injuries are mainly observed in high-speed accidents with high body deceleration and direct load force to the chest. Mostly chest compression is responsible for the load direction to the cardiac vessels. The main observed load vector is from caudal-ventral and from ventral solely, but also force impact from left and right side and in roll-over events with chest compression lead to traumatic aortic injuries. Classically, the injury appeares at the junction between the well-fixed aortic arch and the pars decendens following a kind of a scoop mechanism, a few cases with a hyperflexion mechanism are also described. In our analysis the deceleration effect alone never led to an aortic rupture. Comparing the past 40 years aortic injuries shift from unprotected car occupants to today's unprotected vulnerable road users like pedestrians, cyclists and motorcyclists. Still the accident characteristics are linked with chest compression force under high speed impact, no seatbelt and direct body impact.
Ruptures and dissections of the thoracic and abdominal aortic vessel caused by traffic accidents are rare but potentially life-threatening injuries. They can occur by blunt trauma via seat belt or dashboard injury. The study aimed at evaluating the overall mortality, morbidity, neurological disorders, and differences in operative procedures of open repair and stenting. It shows that, with a change and improvement in diagnostic tools and surgical approach, mortality and morbidity of blunt aortic injuries were significantly reduced. Still an immediate life-threatening injury early diagnosis via multiple-slice and scans and surgical repair with minimally invasive stents showed excellent short-time results for selected patients.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Since 2005, the motorcycle crash fatalities in the US exceeded 10% of the overall annual traffic fatalities. Consequently, it has become critical to gain in-depth understanding of the factors and characteristics contributing to motorcycle crashes. Unfortunately, there currently exists no database gathering the necessary information for an in-depth analysis of the US motorcycle crashes. So this study utilizes the NASS/CDS database (National Automotive Sampling System, Crashworthiness Data System) in order to gain insights into the patterns and factors leading to a NASS/CDS motorcycle crash, from 1997 to 2007. NASS/CDS samples about 5,000 passenger car tow-away crashes per year. Each case includes photographs and detailed data on crash and pre-crash characteristics, vehicle types, trajectories, types of impact, and other pertinent roadway and crash scene information, allowing an in-depth investigation of the crash mechanisms. However, the NASS/CDS sampling process specifically focuses on passenger car crashes, so the cases extracted only correspond to crashes in which a passenger vehicle was towed, and a motorcycle was somehow involved. Thus, a by-hand in-depth review of about 200 cases allowed retrieving 106 relevant crashes for this study, tending to represent the severe passenger vehicle(s) versus motorcycle(s) crashes on US roads. The findings lead to the conclusion that these crashes mostly result from the low conspicuity of the motorcycle, and from the inability of the car drivers to fully appreciate and anticipate the behavior of a motorcycle. Indeed, it has been shown that, first, the car drivers involved in these cases did not attempt any avoidance maneuver, second, they were largely of ages under 25, and finally, the majority of the crashes were in an intersection scenario. In addition, the two major scenarios unveiled were the car attempting a left turn from the opposite direction and the car attempting a left turn from the right. The paper mentions several solutions to enhance the motorcycle- conspicuity and to allow the car drivers to better anticipate its behavior, which seem to be key factors in the intersection-related crashes (and more generally in the passenger vehicle(s) versus motorcycle(s) crashes).
Im September 2013 wurde der 2. CEDR Call (Conference of European Directors of Roads, Call 2013), der eine Summe von ca. 5,3 Mio Euro umfasst, veröffentlicht. Im Rahmen der länderübergreifen europäischen Forschung waren fünf Themen der künftigen strategischen Forschungsplanung und dem anstehenden Forschungsbedarf durch Befragung der europäischen nationalen Straßenbauverwaltungen identifiziert worden: Energieeffizienz, Verkehrssicherheit, Alternde Infrastruktur, Straßen und Umwelt, Verkehrsmanagement. Im Rahmen von Workshops waren zuvor zu diesen fünf Themen "Descriptions of Research Needs" (DoRNs) erarbeitet worden, welche zusammen mit dem Call veröffentlicht wurden. Die wesentlichen Inhalte der DoRNS werden im Beitrag kurz beschrieben.
Wetterbeobachtungen zeigen, dass sich das Klima in den letzten Dekaden gewandelt hat. Unter ökonomischen und unter strategischen Gesichtspunkten bedeutsam ist die zukünftige Entwicklung von extremen Wetterereignissen wie Starkniederschlägen, Hitzewellen oder Überschwemmungen. Die wissenschaftlichen Grundlagen eines vermuteten menschlichen Einflusses auf das Klima analysiert seit 1988 der "Zwischenstaatliche Ausschuss zum Klimawandel" (Intergovernmental Panel on Climate Change, IPCC). Vom IPCC werden unter anderem Projektionen von möglichen zukünftigen Klimaentwicklungen erstellt. Um spezielle Regionen detaillierter zu untersuchen und eine Brücke zwischen globalen Klimaänderungen und lokalen Konsequenzen zu schlagen, werden regionale Klimamodelle verwendet. In der BASt wurde 2009 eine Arbeitsgruppe "Klima" eingerichtet, die eine Risiko-Identifikation in verschiedenen Bereichen der Straßeninfrastruktur und des Straßenverkehrs durchführt. Ziel dieser Arbeitsgruppe ist die Minderung der Verwundbarkeit gegenüber den Folgen des Klimawandels durch die Identifikation regionaler und lokaler Schwachstellen und deren Zusammenführung mit dem Bundesfernstraßennetz. In einem von mehreren Pilotprojekten werden die Risiken von Hang- und Böschungsrutschungen durch die Zunahme von Extremwetterereignissen abgeschätzt. Fernziel ist die Erstellung eines Risikokatasters zur Identifizierung der durch Hangrutschungen besonders gefährdeten Bereiche des Bundesfernstraßennetzes.
Für den Einsatz im Erdbau des Straßenbaus müssen die eingesetzten Geokunststoffe hohen Qualitätsansprüchen genügen. Das Straßenbauregelwerk ist durch die Veröffentlichung der "Zusätzlichen Technischen Vertragsbedingungen und Richtlinien für Erdarbeiten im Straßenbau" (ZTV E-StB 09) in dieser Hinsicht nun vollständig, so dass eine lückenlose Nachverfolgung der Produkte von der Herstellung über die Lieferung bis zum Einbau möglich ist. Wichtig ist jedoch die Einhaltung der Vorschriften und Anforderungen, angefangen beim Hersteller über den Lieferanten, über den Auftragnehmer bis hin zum Auftraggeber, um einen hohen Qualitätsstandard des Produktes und der fertigen Leistung zu garantieren. Hersteller, deren Produkte einer freiwilligen Überwachung unterliegen, können diese Produkte mit einem Qualitätssiegel kennzeichnen und liefern zusammen mit der CE-Kennzeichnung ein Produktzertifikat. Da in diesem Fall auf die Baustoffeingangsprüfung verzichtet werden kann, reduziert sich der finanzielle und zeitliche Prüfaufwand und es wird ein reibungsloser Bauablauf erzielt.
Die Arbeitsgruppe Erd- und Grundbau der Forschungsgesellschaft für Straßen- und Verkehrswesen (FGSV) hat am 12. und 13. März 2003 ihre 10. Erd- und Grundbautagung in Stade ausgerichtet. Im Zusammenhang damit wurde eine Exkursion zu den umfangreichen Erdbauarbeiten auf schwierigsten Untergrundverhältnissen im Zuge der Baumaßnahme der BAB A 26 zwischen Stade und Horneburg realisiert. Die Tagung wurde von circa 300 Teilnehmern besucht, darunter 13 Fachkollegen aus den europäischen Nachbarländern. In insgesamt vier Blöcken der Vortrags- und Diskussionsveranstaltung wurde über neue Technische Regelwerke, Erfahrungen aus der Baupraxis sowie über aktuelle Forschungsergebnisse berichtet und diskutiert.
Die Arbeitsgruppe Erd- und Grundbau der Forschungsgesellschaft für Straßen- und Verkehrswesen (FGSV) hat am 12. und 13. März 2003 ihre 10. Erd- und Grundbautagung in Stade ausgerichtet. Im Zusammenhang damit wurde eine Exkursion zu den umfangreichen Erdbauarbeiten auf schwierigsten Untergrundverhältnissen im Zuge der Baumaßnahme der BAB A26 zwischen Stade und Horneburg realisiert. Die Tagung wurde von circa 300 Teilnehmern besucht, darunter 13 Fachkollegen aus den europäischen Nachbarländern. In insgesamt vier Blöcken der Vortrags- und Diskussionsveranstaltung wurde über neue Technische Regelwerke, Erfahrungen aus der Baupraxis sowie über aktuelle Forschungsergebnisse berichtet und diskutiert.
Absturzsicherung auf Brücken
(2008)
Der Beitrag behandelt den aktuellen Stand der Normung und Ausführung von Absturzsicherungen auf Brücken. Zu den Absturzsicherungen gehören sowohl die Fahrzeug-Rückhaltesysteme als auch Geländer, die den Absturz von Personen verhindern sollen. Die verschiedenen Fahrzeug-Rückhaltesysteme sind: Stahlschutzplanken, Betonschutzwände, transportable Schutzwände und Anpralldämpfer. Die zugehörigen Regelungen finden sich in den Richtlinien für passive Schutzeinrichtungen an Straßen (RPS), die derzeit an die Europäische Norm EN 1317 Rückhaltesysteme an Straßen angepasst werden. Die nationalen Regelwerke müssen auf die in der Europäischen Norm vorgegebenen Leistungsklassen, die die bisherigen Beschreibungen der Schutzsysteme ersetzen, Bezug nehmen. Die dabei zu berücksichtigenden Leistungsmerkmale sind: Aufhaltevermögen, seitliche Auslenkung und Insaßenbelastung. Damit der Anwender Systeme zielgerichtet auswählen kann, sind für alle Schutzsysteme Anprallversuche erforderlich, mit denen das System in eine Aufhalteklasse eingestuft wird. In einer Tabelle werden die Aufhalteklassen (N1, N2; H1,H2,H3; H4a und H4b) mit den bei den Anprallprüfungen einzuhaltenden Versuchsparametern aufgelistet. Normales Aufhaltevermögen gewährleisten die Klassen N1 und N2, höheres Aufhaltevermögen die Klassen H1 bis H3 und sehr hohes Aufhaltevermögen die Klassen H4a und H4b. Am Fahrbahnrand von Brücken wird bei Autobahnen und autobahnähnlichen Straßen im Normalfall die Aufhaltestufe H2 gefordert; bei besonderer Gefährdung Dritter unter der Brücke jedoch H4b. Bei den übrigen Straßen reichen, abhängig vom Schwerverkehrsanteil, die Aufhaltestufen H1 beziehungsweise H2. Da Leistungsanforderungen an die Systeme der Schutzeinrichtungen auf Brücken gefordert werden, sind vom Hersteller Nachweise der auf das Bauwerk einwirkenden Kräfte beim Fahrzeuganprall zu führen.
The price of a new car increased almost every year for a long period. In recent years however, the budget available to most people for purchasing a car either did not grow or became even smaller. Therefore it was in the interest of some OEMs to offer economical car models in the so-called "8,000- Euro class". Here an important question arose regarding the safety of these vehicles. There is no question that the very high safety level of cars reached in Europe during the last decades should not be sacrificed as a consequence of smaller budgets. Customers with sense of responsibility have the right to be properly informed about the balance between safety and price so that they can make a deliberate decision when buying either a new or a used car. Against this background, the German magazine "AutoBILD" commissioned DEKRA to conduct fullscale frontal crash tests with a view to publishing the results. These tests have been carried out in accordance with the corresponding Euro NCAP crash test requirements and performance criteria. The tested vehicles were two new Logans produced by the manufacturer Dacia, two used cars of the type VW Golf IV (registration date 2000) and one new VW Fox. This paper describes the safety features of the vehicles and the results of the five crash tests to demonstrate state-of-the-art safety levels and what levels may be expected from vehicles in the "8,000- Euro class". Looking at real-world crashes it is of interest to think about future trends in a more detailed manner. Therefore it will be more and more necessary to supplement the federal statistics with more detailed in-depth information about the consequences of accidents and the safety performance of crashed vehicles.
It is well known that motorcycle riding is fascinating but quite more dangerous than for example car driving. In 2006, 5,091 persons were killed as victims of crashes occurring on public roads in Germany. 52% (2,683) were car occupants, 16% (793) motorcycle riders, 14% (711) pedestrians, 10% (486) bicycle riders, 5% (235) commercial vehicle occupants, 2% (107) riders of smaller powered two-wheelers, called "Mofa, Moped and Mokick". This shows that motorcycle riders recently are the second largest group of killed traffic participants in Germany. Latest information coming from the Federal Statistics predict for the year 2007 the figure of 4,958 killed road victims in total. This would be again a successful reduction (-133 killed persons or "2.6% compared to the year 2006). But the news coming from the Federal Statistics during the year 2007 and at the begin of 2008 did not always tell the same positive story. It is questioned whether the positive trend of substantially reduced figures of killed road user year by year will longer continue for Germany. That means it could be impossible to reach the ambitious target, set by the European Commission, to cut in half the figure of killed road users until the year 2010 " compared to the figure for the year 2001. It was reported that the group of 45 to 49 years old traffic participants (all traffic modes) is conspicuous with an increase of 30% up to 297 killed road users in total from January to August 2007. This increase can be ascribed in particular by an increase of killed motorcycle riders within this age group. Due to mild weather conditions in Germany in 2007 the season for motorcycle riding began relatively early and this may be a main reason for the increase of the figure of killed motorcycle riders by 16% from January to August 2007. With this background the accident occurrence of motorcycles became more and more essential. As part of the actual discussion about historical trends, recent emphases, causes and relevant structures of the events of motorcycle crashes it is evident, to have latest and carefully updated figures coming from both the Federal Statistics and In-depth studies. The paper will give a contribution to this using the German Federal Statistics and in-depth studies, for example GIDAS. Additional data coming from the DEKRA Motorcycle Accident Database as well as from literature are considered, too. The paper will help to describe the current situation of the accident involvement of motorcycles in Germany.
Tree impacts are still one of the most important focal points of road deaths in Germany. For the year 2008, the latest figures in the national statistics show a share of 28% of road users killed in crashes with trees alongside a road amongst all crashes on rural roads (except the Autobahn). The official German statistics show the attribute "impact on a tree" since 1995. For this first reported year, the share of road users killed in such crashes was 30%. During the last 14 years, fatal accidents with road users killed on rural roads (except the Autobahn) after impacts on a tree declined by 60% from 1,737 (year 1995) to 696 (year 2008). But this is more or less in line with the general evolution of vehicle and traffic safety in Germany. For Germany as a whole the accident statistics do not show a reduction for "treer crashes" which is clearly more than the average for all accidents. But, as shown with the paper, there are different evolutions in the several German States. In public awareness the topic "tree impacts" is mostly associated with the situation in Germany after the reunification. At that time a lot of road users were killed on the avenues in the so called "new countries". The fact that "tree impacts" are still a big share within the figure of killed road users seems to be little-known. Using updated information coming from the official statistics and in-depth-studies, accident researchers can identify a big potential for further improvements of traffic safety on the associated district roads, state roads and federal highways. There is still a need to analyse more details of the accident occurrence with impacts on trees to generate new and updated findings on the current limits and potentials of measures to improve vehicle and traffic safety. To make further efforts in reducing the figures of victims of "tree impacts" the intensification of well-known conventional solutions " for example implementation of guard rails and reduction of speed - is an option. Measures related to vehicle safety technology especially in the field of primary (active) safety will have additional benefit within the physically imposed limits. With this background it can be seen that the subject "tree impacts" should be analysed with a holistic approach taking into account the entire system of driver, vehicle, road, the environment and a social consensus as well.
Do learner gain sufficient braking capabilities at the end of education for collision avoidance?
(2013)
The paper describes a test design to evaluate the braking behaviour in the course of the driver education. The results show that the braking capabilities increased during the driver education and the learning effects are the same for males and females. The evaluation limit is set to 6 m/s-². At the beginning of education, 50% of the drivers do not reach this limit, although the driver education car is equipped with an emergency brake assist, which is regularly installed in all vehicles since 2009. After the education, 100% of the drivers can reach the limit. The results are mapped to a collision avoidance scenario.
Die Autoren erläutern die Beratungen des 37. Deutschen Verkehrsgerichtstages zum Thema "Arzneimittel und Verkehrssicherheit". Die nur durch Prüfung des Einzelfalls zu belegende arzneimitttelbedingte Fahruntüchtigkeit wird in ihrer Komplexität dargestellt. Die offiziellen Empfehlungen des Verkehrsgerichtstages zu diesem Thema werden vorgestellt.
Anwendungsmöglichkeiten und erste Ergebnisse aus Pilotstudien zur Photokatalyse an Straßenbauwerken
(2015)
Zur Frage, ob photokatalytisch aktive Oberflächen im Straßenbau eine Lösung des Stickoxidproblems darstellen können, stellt der Beitrag erste Ergebnisse aus Pilotstudien zu TiO2-Anwendungen vor. Diese betreffen die Untersuchung einer Lärmschutzwand mit TiO2-Beschichtung (A1, Niedersachsen), eine photokatalytisch aktive Straßenoberfläche (NOxer(R)-Belag, B433 in Hamburg, Decke mit Ti02-haltiger Zementschlämme, derzeit noch in Auswertung) sowie einen Tunnel (Tunnelkassetten mit TiO2-Matten im Tunnel Rudower Höhe in Berlin, A113, fortgeführt in Bezug auf die Untersuchung der Haltbarkeit der Kassettensysteme). Ausführlich dargestellt werden die Untersuchungen zur Beschichtung der Lärmschutzwand an der Al mit Titandioxid-haltiger Suspension, den zugehörigen forschungsbegleitenden Studien, sowie den Ergebnissen in Bezug auf die NO2-Minderungsrate. Die bisher durchgeführten Auswertungen haben NO2-Minderungen von einstelligen Prozentzahlen ergeben. Die Entwicklung der Minderungsraten lässt vermuten, dass photokatalytische Suspensionen zum Teil mehrere Monate benötigen, um sich frei zu brennen und die aktiven TiO2-Partikel an die Oberfläche treten zu lassen. Schon die Lärmschutzwand allein bewirkt eine deutliche Verminderung der NO2-Konzentrationen im direkten Hinterland durch Verfrachtung der Luftschadstoffe in höhere Luftschichten.
Police records about traffic accidents like used by IRTAD (International Road Traffic and Accident Database) and CARE (Community Road Accident Database) do not represent all road injuries. For instance, road accidents of bicyclists without a counterpart are usually not reported. Furthermore, IRTAD-like data contains hardly any information on injury outcome and accident circumstances. This information gap leads to an under-representation of the safety concerns of the most vulnerable road users like children and the elderly both in accident research and safety promotion. Injury registration for the European Injury Database (IDB), in turn, combines details of accident causation with diagnostic information that can be used to assess injury severity and long term consequences. The IDB is collecting data from hospital emergency department patients and is being implemented in a growing number of countries. In this article IDB results on mode of transport and injury outcome are presented from a sample of nine EU member states.
Beside numerous information about vehicles injuries and environmental data the GIDAS database contains detailed reconstruction data. This data is calculated by a reconstruction engineer who handles about 1000 accidents per year. The spectrum of one reconstruction ranges from simple crossing accidents to complex run-off accidents with rollover events. Especially for complex accident scenarios there is a large effort to design the environment of the accident scene within PC-Crash ®. To reduce the reconstruction time by maintaining the high quality of reconstruction 3D-geodata can be useful. Geodata is available for nearly every area in Germany and can be used for a fast and detailed creation of complex accident environments. In combination with the accident sketch areal images of the accident scene can be created and the participants are implemented in the new-built 3D-reconstruction environment. As a consequence, the characteristics of the terrain can be considered within the reconstruction which is especially important for run-off accidents.
Analysis of pedestrian leg contacts and distribution of contact points across the vehicle front
(2015)
Determining the risk to pedestrians that are impacted by areas of the front bumper not currently regulated in type-approval testing requires an understanding of the target population and the injury risk posed by the edges of the bumper. National statistics show that approximately 10% of all accident casualties are pedestrians, with 20% to 30% of these pedestrian casualties being killed or seriously injured. However, the contact position across the front of the bumper is not recorded in national statistics and so in-depth accident databases (OTS, UK and GIDAS, Germany) were used to examine injury risk in greater detail. The results showed that some injury types and severities of injuries appear to peak around the bumper edges. Although there are sometimes inconsistencies in the data, generally there is no evidence to suggest that the edges of the bumper are less likely to be contacted or cause injury.
In-depth road traffic accident research in Spain is a fairly recent activity. In the past, only accident data that had been retrospectively processed by the national and regional traffic police forces was available. In 1999 Applus+IDIADA set up a permanent accident research unit to carry out indepth analysis of road accidents in Spain. Since then accidents involving cars, motorcycles, coaches and vulnerable road users have been thoroughly studied. The Applus+IDIADA accident research team has carried out work for the various traffic polices in Spain and it is currently involved in several research projects in which accidentology is one of the main tasks. The working methodology of the team is presented in the first part of the paper. In the framework of the European research project "Rollover" (GRD2-2001-50086), Applus+IDIADA has collected data, inspected scenarios and performed virtual reconstructions of twenty-six of the total seventy-six rollover accidents studied. The second half of the paper describes how these accident investigations were used to develop a test procedure for identifying possible improvements to the vehicle structure which augment occupant protection in a rollover scenario. In particular, a proposal for a new drop test for rollover assessment is presented. The cases were analysed for severity, in terms of injury to the occupants and damage to the vehicle, and taking into account whether a seatbelt was worn or not. The worst possible cases were identified as those that had severe occupant injuries and sizable damage to the occupant compartment when seatbelts had been worn. The most severe cases were then analysed further for impact position (roll and pitch angles) and the impact velocity. With these parameters taken into account, the most representative combinations could be found. This resulted in a series of configurations for possible drop tests. The results of the tests indicate where passenger vehicle structures need to be improved in order to increase occupant safety in the event of a rollover crash.
The aim of this study is to investigate the differences in car occupant injury severity recorded in AIS 2005 compared to AIS 1990 and to outline the likely effects on future data analysis findings. Occupant injury data in the UK Cooperative Crash Injury Study Database (CCIS) were coded for the period February 2006 to November 2007 using both AIS 1990 and AIS 2005. Data for 1,994 occupants with over 6000 coded injuries were reviewed at the AIS and MAIS level of severities and body regions to determine changes between the two coding methodologies. Overall there was an apparent general trend for fewer injuries to be coded at the AIS 4+ severity and more injuries to be coded at the AIS 2 severity. When these injury trends were reviewed in more detail it was found that the body regions which contributed the most to these changes in severity were the head, thorax and extremities. This is one of the first studies to examine the implications for large databases when changing to an updated method for coding injuries.
The Centre for Automotive Safety Research (formerly the Road Accident Research Unit) at the University of Adelaide in South Australia has a history of in-depth crash investigation going back to the 1970s. In recent years, our focus has been on studying factors that contribute to road crashes, with an emphasis on the role of road infrastructure. Our method involves crash notification by the South Australian Ambulance Service and detailed investigation of the crash scene usually before the crash-involved vehicles have been moved. This at-scene data collection is supplemented with police crash reports, Coroner- reports including autopsy findings for fatal crashes, case notes from hospitals for all injured persons, structured interviews with crash participants and witnesses, and computerised reconstruction of the events of the crash. One of the most notable research findings to emerge from our in-depth work has been the relationship between travelling speed and the risk of crash involvement. By comparing the calculated free speeds of crash-involved vehicles (cases) with the measured speeds of non-crash-involved vehicles travelling on the same roads at the same time of day (controls), we were able to establish that an exponential relationship exists between travelling speed and the likelihood of involvement in a casualty crash. This was the case for both metropolitan and rural areas. This research prompted the reduction of some speed limits in Australia, which has resulted in notable decreases in crash numbers. Another finding of interest in our recent investigation of 298 mostly daytime crashes in metropolitan Adelaide was that medical conditions make a sizeable contribution to the occurrence of road crashes. We found that almost half of the drivers, riders and pedestrians involved in the collisions had at least one pre-existing medical condition, and half of these individuals had two or more such conditions. We found that a medical condition was the direct causal factor in 13% of the casualty crashes investigated and accounted for 23% of all hospital admission or fatal crash outcomes. A follow-up study of all hospital admissions for road crashes in Adelaide is now going ahead to look further at this problem. The paper also describes studies looking specifically at pedestrian crashes. These include studies of the relationship between travelling speed and the risk of a fatal pedestrian crash, and studies utilising real crash data to validate headforms and test dummies used in the assessment of the safety of new vehicles in the event of a collision with a pedestrian.
While it is important to track trends in the number of road accidents in different countries using national statistics, there is a need for data with more detailed information, so called in-depth accident data. For this reason, several accident data projects emerged worldwide in recent years. However, also different data standards were established and so comparative analysis of international in-depth data has been very hard to conduct, so far. This is why the project iGLAD (Initiative for the Global Harmonization of Accident Data) was established and created the prerequisites for building up a standardized dataset out of the common denominator of different in-depth accident databases from Europe, USA and Asia. In the first phase, the project received funding from ACEA to compile an initial database. To accomplish this, a suitable data scheme has been defined, a pilot study has been conducted as proof of concept and the recoding of the first common data base has been initiated. Also, to prepare the project for its self-supporting continuation in the next years, a business model has been developed. This paper reports the history and status of the project, the current challenges and the creation of a capable consortium to maintain the data. In mid-2014, the initial database containing 1550 cases from 10 different countries will be completed and a first detailed view on this data will be possible.
Many safety-relevant tasks in control or diagnostics require binary choices such as "conflict versus separation" in air traffic control, "normal versus pathological" when interpreting x-ray pictures, or "permitted versus forbidden" when inspecting airport security scans. Deciders often are uncertain, but nevertheless required to decide between two alternatives, that is, they have not only to decide upon an action, but also about the admissible level of uncertainty. If the accepted level of judgment certainty is not taken into account, the sequence of decisions does not capture the full picture of the underlying decision process. Differences in judgment certainty are relevant, because they reflect not only the adequacy of the human-machine interface that is evaluated, but also the differences in expertise of the decider and the requirements of the actual situation or task. Therefore, capturing both judgment certainty and discrimination performance is essential. A comparison of different human-machine-interfaces (for air traffic control) is used to illustrate a methodological approach, which allows for integrated analyses of decision processes based on receiver-operator-characteristics and practical guidelines for the evaluation of human-machine-interfaces for safety-relevant operation procedures are provided.
Es wird über aktuelle Arbeiten zur Unfallprävention bei jungen Fahrern und Fahranfängern berichtet. Hierzu hat im Oktober 2001 die internationale Konferenz "Junge Fahrer und Fahrerinnen" stattgefunden. Außerdem wird auf die Auswertung internationaler Erfahrungen mit neuen Maßnahmenansätzen zur Unfallprävention bei jungen Fahrern und Fahranfängern und die Einrichtung einer Projektgruppe "Begleitetes Fahren" der Bundesanstalt für Straßenwesen hingewiesen.
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
Offenporige Asphaltbeläge besitzen mit 22 % Hohlraum im Belag und einer groben Kornstruktur an der Oberfläche einen wesentlich anderen Aufbau als dichte Beläge. Nach vorliegenden Erfahrungen und Ergebnissen von durchgeführten Untersuchungen erfordern die Belagseigenschaften der offenporigen Asphaltbeläge eine andere Anwendung von Tausalz. Die Bundesanstalt für Straßenwesen (BASt) führte in den vergangenen Jahren gemeinsam mit der Firma KOMMZEPT-Ingenieurbüro Hausmann umfangreiche Untersuchungen zum Salzeinsatz auf offenporigen Belägen durch. Dazu gehörten Laborversuche, Messungen zur Verweil- und Wirkungsdauer von Tausalz auf diesen Belägen und Auswertungen der Beobachtungen von Autobahnmeistereien in Bayern, Brandenburg und Niedersachsen. Die Ergebnisse der Untersuchungen zeigen, dass die offenporigen Beläge teilweise winterdienstlich anders behandelt werden müssen als die dichten Beläge. Die Offenporigen Asphalte besitzen im Vergleich zu dichten Belägen eine deutlich rauere Oberflächenstruktur. In den Poren des Belags fließt Wasser nicht vollständig ab. Durch Kapillarwirkungen lagert sich Wasser im Belag ähnlich wie in einem Schwamm ab. Dieses Wasser im Belag kann durch den Verkehr sogar wieder zur Oberfläche gesaugt werden, an der es bei Temperaturen unter 0 -°C vor allem nachts zu einer Eisschicht kommen kann. Aufgrund der größeren gebundenen Wassermengen muss mehr Salz auf offenporigen Asphalten gestreut werden. Ausgebrachtes Tausalz bleibt länger in den Oberflächenporen oder im Belag haften. Es wird im Vergleich zu dichten Belägen durch den Verkehr fast nicht zur Seite verweht. Vorbeugend ausgebrachtes Feuchtsalz dringt langsam in die Oberfläche ein. An den eigentlichen Kontaktflächen zum Reifen bleibt wenig haften. Deshalb ist der Einsatz von Tausalzlösungen bei Reifglätte oder geringer Feuchte (Nieselregen) wirkungsvoller.
This study updates previous IIHS studies comparing estimated delta Vs for crash tested vehicles to the distribution of estimated delta Vs in the National Automotive Sampling System (NASS) Crashworthiness Data System (CDS). The delta V estimates for 232 frontal crash tests at 64.4km/h into a deformable barrier with 40 percent overlap are compared with estimates from frontal offset crashes in the 1997-2004 NASS database. All delta V estimates were based on SMASH, the delta V estimating program used by NASS since 1997. Results indicated that for all vehicles tested by IIHS, SMASH delta Vs were, on average, 32 percent lower than impact speeds and about 28 percent lower than the expected delta V. Almost 80 percent of all real-world frontal crashes resulting in AIS 3+ injuries and just over 60 percent of all fatal crashes occur at or below the average estimated delta V calculated for crash tested vehicles.
Um ein Bild von der aktuellen Messunsicherheit bei der Bestimmung von Tetrahydrocannabinol (THC) in Serum zu erhalten, wurden von sieben forensisch-toxikologischen Laboren rechtsmedizinischer Institute Daten der letzten Jahre erhoben. Zur Abschätzung der Messunsicherheit wurde eine Einteilung in zufällige Fehler (Präzision) und systematische Fehler (Richtigkeit) vorgenommen. Ergebnisse zur Richtigkeit wurden aus Daten von Ringversuchen ermittelt. Es ergab sich eine mittlere erweiterte Messunsicherheit für die THC-Bestimmung von ca. 33 %, das heisst, bei einem Messwert von 1 ng/ml liegt der "wahre Wert" mit circa 95 prozentiger Wahrscheinlichkeit im Intervall zwischen 0,67 und 1,33 ng/ml. Dieses Ergebnis bestätigt, dass die verwendete Analytik geeignet ist, bei Konzentrationen um 1 ng/ml einen sicheren Substanznachweis zu führen. Es ist erkennbar, dass bei der THC-Bestimmung im Serum in der Regel der Richtigkeitsanteil an der Messunsicherheit größer ist als der Präzionsanteil.
Bone fracture patterns could be crucial in reconstructing the nature of loading, especially in the lower limb and upper limb kinematics in vehicle-pedestrian crashes. In addition, use of FE bone models can be a handy tool to predict vehicle impact velocity and the impact direction. The point of fracture initiation in bone loading has been predicted quite accurately earlier. A methodology that predicts bone crack initiation and its propagation pattern for the six known loading directions using a single material and failure model is presented.
In order to improve the protection of children transported in cars, within the CHILD programme (GR3D-CT2002-00791) real world road accidents are thoroughly analysed and then reconstructed in laboratory. Prior to comparing injury severities of real victims to physical parameter values measured on the dummies, the quality of the reconstructions is evaluated by experts who use their experience based on the investigation of numerous and various accidents. This paper presents a new tool aiming at better evaluating and validating accident reconstructions. It is based on statistical evaluation of vehicle deformations which gives weighing factors for every part of the car body structure finally leading to a specific Reconstruction Quality Score (RQS indicator). Furthermore, the reliability of this score, depending on the number of measured points, can be established. This tool includes a function aiming at adjusting the speed for a further reconstruction and at defining the launching speed and the pulse shape for complementary sled tests. Finally, the functions of the RQS software and database are presented.
Nach Anlage 5 (2) der Fahrerlaubnisverordnung (FeV) verlangt der Gesetzgeber von Bewerbern um die Erteilung oder Verlängerung einer Fahrerlaubnis der Klassen D, D1, DE, D1E sowie der Fahrerlaubnis zur Fahrgastbeförderung die Erfüllung besonderer Anforderungen hinsichtlich Belastbarkeit, Orientierungsleistung, Konzentrationsleistung, Aufmerksamkeitsleistung sowie Reaktionsfähigkeit. Die zur Untersuchung dieser Merkmale eingesetzten testpsychologischen Verfahren müssen nach dem Stand der Wissenschaft standardisiert und unter Aspekten der Verkehrssicherheit validiert sein. Zur Klärung der Fragen, wie ausgedehnt das Spektrum eingesetzter und akzeptierter Testverfahren ist und welche Erfahrungen die Gutachter bisher gemacht haben, fand am 07.11.2000 in der Bundesanstalt für Straßenwesen ein Expertengespräch statt. Dieses Gespräch zeigte unter anderem folgende Ergebnisse: Zum Einsatz kommen insbesondere das Act-and-React-Testsystem (ART) und das Wiener Testsystem (WTS), weiterhin die Testbatterien zur Aufmerksamkeitsprüfung (TAP). Die als Grenzwerte festgelegten Prozentränge von 33 beziehungsweise 16 sind empirische Setzungen, als Referenz wurden bewusst altersunabhängige Normwerte gewählt. In einigen Bundesländern sind die Begutachtungsstellen für Fahreignung erste Anlaufstellen, in anderen die Betriebs- oder Arbeitsmediziner. Die Durchführung der Testverfahren kann durch einen qualifizierten Arzt, Psychologen oder eine geschulte Testassistentin erfolgen. Sobald sich die Frage einer Kompensationsprüfung stellt, ist eine differenzierte psychologische Untersuchung erforderlich. Bei unauffälligen Befunden kann das Gutachten weitgehend standardisiert sein. Abschließend sind Forderungen für die weitere Entwicklung formuliert.
The current Brussels EU Regulation No. 1235/2011, valid from May 30, 2012, has introduced an European Tyre Label with wet grip index G classes from A to G for passenger car tyres C1, light commercial vehicles tyres C2 and heavy truck- and bus tyres C3. Every wet grip class for each vehicle category has a defined band of numerical values for the wet grip index G. The legislated wet grip values G in this EU- Regulation are very low. The measured braking distances and corresponding impact speeds of the test vehicles are showing very critical results. Regulation No. 1235/2011 of the European Parliament and the Council for Type Approval of Vehicles (EU) should be changed in such a way, that for C1-tyres (normal passenger cars tyres) the minimum wet grip index G is 1.25. All C2-tyres (light commercial vehicles tyres) should at least meet a minimum wet grip index of G = 1.1. All C3-tyres (heavy trucks and buses tyres) should at least meet a minimum wet grip index of G = 0.95. Due to the missing lower limits for G in the wet grip class F for C1, C2 and C3 tyres according to Commission Regulation (EU) No. 1235/2011, officially valid from 30 May 2012, a tyre-to-road coefficient of adhesion in the extreme of 0 (zero) is legally permitted. This is an apparent flaw in above cited EU Regulation, which causes a potential danger to the road traffic safety for all motor vehicles in Europe with such tyres. The wet grip class F has to be removed urgently from said EURegulation, since a direct liability of the responsible EU-Commission can not be excluded.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
The objective was to develop and validate a crash trolley (reference vehicle) equipped with a compartment and a full restraint system for driver and front seat passenger which can be used in full scale crash testing. Furthermore, the crash trolley should have a suspension to show rotation and nick effects similar to real vehicles. Within the development phase the reference vehicle was build based on a European family car. Special attention was needed to provide appropriate strength to the trolley and its suspension. The reference vehicle is equipped with a restraint system consisting of airbags, pedals, seats, dashboard, and windscreen. On the front of the vehicle different crash barriers can be installed to provide miscellaneous deceleration pulses. For the validation phase a series of low and high speed crash tests with HIII dummies were conducted and compared with full scale tests. For the comparison deceleration pulse, dummy numbers and vehicle movement were analyzed. Validation tests with velocities up to 60 km/h showed promising results. The compartment and the suspension systems stayed stable. Rotation effects were comparable with full scale car crash tests. The airbags and seat belt system worked reasonable. The acceleration pulse compared to an Euro NCAP test had a similar characteristic but was in general slightly lower. After the successful validation the reference vehicle is already in use in different studies in the field of vehicle safety research at BASt.
Detailed anthropometric data of pregnant women have been collected and used in the development of a computational model of the pregnant occupant model "Expecting". The model is complete with a finite element uterus and multi-body fetus, which is a novel feature in the models of this kind. The computational pregnant occupant model has been validated and used to simulate a range of impacts. The strains developed in the utero-placental interface are used as the main criteria for fetus safety. Stress distributions due to inertial loading of the fetus on the utero-placental interface play a role on the strain levels. Inclusion of fetus model is shown to significantly affect the strain levels in the utero-placental interface. This series of studies has led to the design of seatbelt features specifically for the pregnant women to enable them use the seatbelt correctly and comfortably.
In 2014 the sixth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
In 2012 the fifth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
The second ESAR Conference took place at the Medical University Hannover. This year conference presents the current state of affairs of relevant research activities in the field of in-depth investigations. The first conference on ESAR (Expert Symposium on Accident Research) was established in 2004. It is planned to hold ESAR every two years. Hannover seems to be the right place for this conference concerning the fact that the first in-depth research team was found here in the year 1973 and comprehensive studies on accident analysis were spread out from here around the world continuously. This year conference topped all expectations in terms of the numbers of participants, in the variety of papers and the interdisciplinary of presenters from medical, psychological and engineering background. More than 100 delegates from all over the world, that means 13 different countries and from 4 different continents, came to Hannover, presented their results of accident investigation and discussed countermeasures for accident prevention and injury reduction. ESAR should be a platform for exchange of knowledge to find an optimized way for increase of traffic and vehicle safety by in-depth investigation and methodology. ESAR as international conference should be a platform for consideration of all nations round the world. This seems to be very important for the current situation, having high safety in the high industrial countries of Europe, US and Australia, but low safety and high injury risk in Asia and Africa.
Das einwohnerbezogene Risiko, im Laufe eines Jahres im Straßenverkehr zu sterben, steigt bei Kindern und Jugendlichen von 17 Getöteten je 1 Mio. Einwohner im Kindesalter über, 112 Getötete je 1 Mio. Einwohner im Alter von 15 bis 17 Jahren bis zu 207 Getötete je 1 Mio. Einwohner und Jahr im Alter zwischen 18 und 24 Jahren. Das ist ein Anstieg um das 12fache. Vor diesem Hintergrund wird im Programm für mehr Sicherheit im Straßenverkehr des BMVBW des Jahres 2001, (Seite 14) gefordert ...Verkehrserziehung in der Schule in allen Jahrgangsstufen durchführen... Die Ergebnisse der Studie "Verkehrserziehung in der Sekundarstufe" stellten die Grundlage dieses Kolloquiums dar. Rund hundert Experten aus dem Bereich Verkehrserziehung nahmen an der Veranstaltung teil, darunter die für Verkehrserziehung zuständigen Referenten der Länder, Fachberater für Verkehrserziehung, Lehrer und Polizeibeamte und zahlreiche Vertreter wissenschaftlicher Institute, der Lehrerfortbildung und der Verbände, die sich mit der Verkehrs- und Mobilitätserziehung befassen. Horst Weishaupt präsentierte die Ergebnisse der von der Bundesanstalt für Straßenwesen in Auftrag gegebenen Studie zur Situation der Verkehrserziehung in der Sekundarstufe. Dabei stellte er unter anderem dar, dass die Verkehrserziehung im Denken vieler Lehrer und Lehrerinnen keine wesentliche Rolle spielt. Er verwies aber auch darauf, dass die Situation der Verkehrserziehung je nach Schulart, Jahrgangsstufe, Größe der Schule und Bevölkerungsdichte unterschiedlich ist. Horst Roselieb vom niedersächsischen Kultusministerium hinterfragte die KMK-Empfehlungen für Verkehrserziehung von 1994 vor dem Hintergrund der "Weishauptstudie". In seinem Vortrag "Vom Ringen der Schulen um Wirksamkeit" betrachtete Michael Felten die Ergebnisse der Studie aus der Sicht des Lehrers und vor dem Hintergrund der allgemeinen Diskussion um den Zustand der Schule von heute. Er plädierte dafür, die Schüler stärker zu fordern und über den sich einstellenden Lernerfolg die Freude an der Leistung und am Lernen zu erhöhen. In Workshops wurden die Ergebnisse der Studie diskutiert. In Workshop I: "Verkehrs- und Mobilitätserziehung in der Sekundarstufe: Chancen, Ziele, Grenzen" forderten die Teilnehmer - den Stellenwert der Verkehrs- und Mobilitätserziehung künftig zu erhöhen. - Die Empfehlungen für Verkehrserziehung der KMK auf Umsetzbarkeit und Akzeptanz in der Lehrerschaft zu überprüfen. - Klarheit hinsichtlich der wesentlichen Inhalte, Ziele und Methoden der Verkehrs-/Mobilitätserziehung zu schaffen. - Verkehrs- und Mobilitätserziehung in den Lehrplänen aller Bundesländer zu verankern. - Inhalte der Verkehrs-/Mobilitätserziehung überprüfbar zu machen. - Verkehrserziehung in die Lehrerausbildung zu integrieren. - Die Lehrerfortbildung zu verstärken. - Verkehrserziehung als kontinuierliche Aufgabe zu verstehen, die alle Altersgruppen einschließt. Die Teilnehmer am Workshop II "Unterrichtsangebote für Verkehrs- und Mobilitätserziehung durch Verbände und Verlage" kamen unter anderem zu folgenden Ergebnissen: - Angebote für Verkehrs- und Mobilitätserziehung sollten folgende Kriterien erfüllen: -- schneller und wiederholbarer Einsatz, -- geringer Organisationsaufwand, -- kurze Vorbereitungszeit, - Angebote sollten moderne Anspracheformen beinhalten: -- Gruppenerfahrung fördern, -- aktive Mitarbeit beinhalten, -- praktische Erfahrungen einbeziehen, - In der Aus-, Fort- und Weiterbildung der Lehrer muss Verkehrs- und Mobilitätserziehung inhaltlich und methodisch einbezogen werden. Im Workshop III "Wissenschaftliche Studien an Schulen" wurde unter anderem gefordert bei der Durchführung bundesweiter Studien - die Genehmigungsverfahren anzugleichen, -und gegebenenfalls Standards für den Datenschutz zu schaffen. Insgesamt fand das Kolloquium bei den Teilnehmern eine sehr positive Resonanz. Auf der Basis der erarbeiteten Anregungen zur Verbesserung der Verkehrserziehung an weiterführenden Schulen, sollen jetzt in einer Arbeitsgruppe der Bundesanstalt für Straßenwesen, in der alle für Verkehrserziehung zuständigen Referenten der Länder vertreten sind, umsetzbare Lösungsvorschläge erarbeitet werden.
In der Öffentlichkeit wird allgemein angenommen, dass Massenunfälle aufgrund schlechter Straßen- und Sichtverhältnisse passieren, vor allem bei Nebel. Statistisch gesehen ereignet sich das Ineinanderfahren zahlreicher Fahrzeuge aber wesentlich häufiger bei guter Sicht. Was sind die Gründe? Dieser Frage wurde auf einem Presseseminar des Bundesministeriums für Verkehr am 14. und 15. September 1994 in Kassel nachgegangen. Dabei wurde das Phänomen des Massenunfalls aus den verschiedensten Blickwinkeln betrachtet: Was ist ein Massenunfall? Wie arbeitet die Polizei? Welche Probleme haben Rettungsdienste und Notfallmediziner? Was geht im Kopf der beteiligten Autofahrer vor sich? Gibt es technische Hilfen und wirksame Lernsysteme?
In 2016 the seventh ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
In recent years considerable progress in active and passive safety of road vehicles has been made. The road traffic of today is much safer than in the past. A current vehicle has a lot more safety elements resulting in an improved inner and outer technique. In most European countries the number of fatalities is decreasing despite growing traffic and road usage. Nevertheless, the number of casualties in road traffic accidents is high enough, thus more progress is needed if the number of fatalities is to be reduced by 50%, as postulated by the European Commission for the year 2010. In order to develop countermeasures and further possibilities for injury prevention, it is increasingly important to have accident data available, supplying results quickly and giving the best overview across Europe. In-Depth-Data Sampling Procedures have a huge historical development, starting in the 60ies by the car manufactures, continued during the 70ies mostly by some universities mainly in England, Sweden, France and Germany, today a net of in-depth-investigation teams are working across Europe and around the world.One of the oldest teams is located at the Hannover Medical School, founded in 1973 by the German Government on behalf of the Federal Highway Research Institute Bast. It was the only team worldwide that was equipped with blue light emergency cars, working on scene in time so directly after the event and working continuously during the years, collecting 20 thousand accidents within 30 years period. Since 1999 the order is carried out in cooperation with the German car industry, which is interested and has benefit on the data too. On the basis of the new data collection, so called GIDAS (German In-Depth Accident Study), that has been run at the Technical University Dresden and the Medical University Hannover), a special tool for In-Depth-Accident Analysis was founded. It is the task of this conference to build a platform for such research based on In-Depth-Investigation. The conference is specially aimed at the area of accident data analysis in order to contribute to the harmonization of different investigation methods and accumulation of different results that does exist for different countries worldwide. Up to now no special conference did exist to deal with accident data only following in the discussion for an improvement in traffic and vehicle safety. ESAR - expert symposium on accident research - should be a step forward. This first international conference is being organized by the Accident Research Unit at the Medical University Hannover jointly with the German Federal Highway Research Institute Bast and the Research Association of German Car Manufacturers FAT. The conference should be a platform for an interdisciplinary exchange of information based on the different presentations from participants around the world.
In September 2004 the first international symposium called ESAR (Expert Symposium on Accident Research) was carried out at the University of Hannover (Germany). The idea for such international conference was to bring together experts from the fields of accident investigation teams worldwide to present their results for a common audience of people from government, industry and other universities. The first conference was a really sufficient one and followed by the second symposium also at the Hannover Medical School two years later in 2006. This two year rhythm was now continued with the third conference in Hannover again in 2008. It is planned to carry out ESAR every two years also in the future. ESAR is a scientific colloquium and can be seen as a platform for exchange of information on accident research issues based on methodologies of investigation, injury mechanisms and injury assessment, accident causation and other issues of statistical accident data analysis. Representatives from authorities as well as from medical and technical institutions come together to discuss new research issues and exchange experiences on accident prevention and the complex field of accident reconstruction. Special focus was given to the target the European Union set for itself in 2000 which stipulates that within 10 years the number of person killed in road traffic accidents must be cut in half. To reach this goal, optimized measures, comprehensive research and analysis are necessary. A key hurdle comes from the European Union extension to 27 member states, each featuring different levels of traffic safety standards and different accident scenarios. Existing results from long term research projects in Europe, the USA, Australia and Japan including analyses of infrastructure, population, vehicle fleet and driver behaviour offer an excellent basis for understanding and improving countermeasures and research support needs in underdeveloped countries. ESAR's goal is to bring together researchers from all parts of the world, who will report on their methods and recommendations to improve traffic safety based on "In-Depth-Investigations" of real world accidents. These In-depth-investigations of accidents require thorough documentation and an accident data analysis on multidisciplinary levels which must be carried out immediately after it occurs. ESAR presents scientists the opportunity to present their studies on a common basis of research level.
Im Jahr 2004 fand an der Medizinischen Hochschule Hannover die erste ESAR-Konferenz (Expert Symposium on Accident Research) statt. Die Idee einer internationalen Konferenz war aus der Notwendigkeit entstanden, diejenigen Experten zusammen zu bringen, die weltweit tätig sind und Verkehrsunfälle wissenschaftlich analysieren, um ihre Ergebnisse gemeinsam zu diskutieren und einem Zielpublikum von Behördenvertretern, Entwicklungsingenieuren der Automobilindustrie und anderen Wissenschaftlern darzubringen. Die durch Professor Otte initiierte und nun zum vierten Male organisierte Konferenz fand eine breite Akzeptanz und ist mittlerweile Bestandteil einer Konferenzlandschaft mit Zielvorträgen von der Fahrzeugsicherheit bis hin zur Verletzungsanalyse und den Unfallursachen. ESAR kann als wissenschaftliches Kolloquium und Plattform für einen Informationsaustausch der Unfallforscher angesehen werden, die sich speziell mit Methoden der Unfalluntersuchung, mit Verletzungsmechanismen und der Bewertung von Verletzungen, Unfallursachen und anderen Bereichen der statistischen Unfalldatenanalyse befassen. Experten aus den Bereichen der Medizin, der Verkehrspsychologie und der Technik sowie Vertreter zuständiger Behörden kommen hier zusammen, um die Erfahrungen in der Unfallprävention und der Unfallrekonstruktion zu diskutieren und um der Forschung neue Felder zu eröffnen. Neben den Belangen der Europäischen Gemeinschaft werden auch die weltweit zu registrierenden hohen Verletztenzahlen berücksichtigt. Wissenschaftliche Vorträge aus aller Welt tragen dazu bei, geeignete Maßnahmen und Methoden zur Analyse und drastischen Verringerung der Zahl der bei Verkehrsunfällen Getöteten zu entwickeln. Die Zusammensetzung des Teilnehmerkreises dieser wie früherer ESAR-Konferenzen hat längst eine über Europa hinausgreifende Internationalitaet erreicht und bietet daher einen aufschlussreichen Überblick über die verschiedenen Standards bestehender Verkehrssicherheit und unterschiedlichen Unfallszenarien und über die Anforderungen an die Unfallanalysen. Die Ergebnisse langjähriger Forschungsarbeiten in Europa, USA, Australien und asiatischen Ländern beinhalten unterschiedliche infrastrukturelle Zusammenhänge und geben Erkenntnisse über Population, Fahrzeugbestand und Fahrereigenschaften. Derartige Informationen bilden eine exzellente Basis für abzuleitende Empfehlungen und Maßnahmen für die Erhöhung der Verkehrssicherheit international.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 15. Oktober 2009 in Baden-Baden ihr 7. Symposium \"Sicher fahren in Europa\". Nach 1991, 1994, 1997, 2000, 2003 und zuletzt 2006 trafen sich auch dieses Mal wieder zahlreiche Fachleute aus Wissenschaft und Politik, Industrie, Wirtschaft und Verbänden aus dem In- und Ausland, trugen neue Forschungsergebnisse vor und erörterten aktuelle Ansätze zur Erhöhung der Verkehrssicherheit. Dabei ging es in den Referaten und Diskussionsbeiträgen und in den vier Workshops vor allem darum, die verkehrspolitischen Entwicklungen und Herausforderungen für die europäische Verkehrssicherheitsarbeit im Hinblick auf folgende Themen zu beleuchten: "Verkehrssicherheit Junger Fahrer", - Das "Auto der Zukunft", - "Demographischer Wandel", - "Landstraßensicherheit". Den Grundsatzreferaten folgten vertiefte Bearbeitungen in den Workshops. Die CD-ROM dokumentiert die Grußworte, Referate und Diskussionsbeiträge.
Im September 2005 wurde erstmals eine FERSI Scientific Road Safety Research Conference durchgeführt. Mit der Konferenz sollten Resultate und Bearbeitungsstände der gemeinsamen europäischen Forschungsprojekte der FERSI Mitglieder präsentiert werden. Darüber hinaus sollten die Ergebnisse wichtiger nationaler Forschungsprojekte eingebunden sowie den Projektbearbeitern Gelegenheit zum internationalen "Networking" gegeben werden. Wolfgang Hahn, Leiter der Abteilung Straßenbau und Straßenverkehr beim Bundesministerium für Verkehr-, Bau- und Wohnungswesen unterstrich in seiner Eröffnungsrede die Notwendigkeit einer in Europa koordinierten Verkehrssicherheitsforschung, um gemeinsam zu einer Verbesserung der Straßenverkehrssicherheit zu gelangen. Aus Sicht des Leiters des Referates "Sicherheit im Straßenverkehr" der DG TREN, Dimitrios Theologitis, besteht die zentrale Aufgabe der zukünftigen europäischen Verkehrssicherheitsforschung in der Entwicklung und Verbreitung von "Best Practices". Auch er betonte, dass die Verkehrssicherheitsprobleme in Europa auch in Zukunft nur durch eine enge Zusammenarbeit der EU-Mitgliedsländer im Bereich der Forschung und durch die Umsetzung der dabei erzielten Forschungsergebnisse zu lösen seien.rnIm Anschluss an die Eröffnungsreden stellten Rune Elvik, TOI (Norwegen), Marc Gaudry, INRETS (Frankreich), David Lynam, TRL (United Kingdom) und Dr. Rudolf Krupp, BASt (Germany), in ihren Vorträgen herausragende Forschungsergebnisse im Bereich der Straßenverkehrssicherheit vor. Die sich an diese erste Vortragsrunde anschließenden Workshops waren entsprechend der Themenschwerpunkte "Daten, Strategien und Kommunikation", "Verhalten und Aufklärung" sowie "Technische Anwendungsmöglichkeiten" unterteilt. Jeder Themenschwerpunkt wurde durch 4 nacheinanderfolgende Workshops abgedeckt. In einer abschließenden Sitzung wurden die wichtigsten Ergebnisse der einzelnen Workshops vom jeweiligen Chairman des Workshops dem gesamten Plenum vorgestellt. rn