620 Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (45)
- Buch (Monographie) (18)
- Wissenschaftlicher Artikel (4)
- Arbeitspapier (1)
Schlagworte
- Injury (68) (entfernen)
Institut
To assess occupant safety in a crash test, criteria associating the measurements made with a crash test dummy to injury risk are necessary. To enable better protection of elderly car occupants the objective of this study was to develop improved thoracic injury criteria for the THOR average male dummy. The development of these criteria is usually based on matched dummy and Post Mortem Human Surrogate (PMHS) tests by relating the obtained PMHS injuries to dummy measurements. This approach is limited, since only a few tests in relevant loading conditions are available and any new test series requires high efforts to be performed due to their complexity and costs. To overcome these limitations and to extend the dataset for the development of THOR dummy chest injury risk functions a simulation-based approach was applied within the EC funded project SENIORS (Safety Enhanced Innovations For older Road Users - www.seniors-project.eu). Within this study frontal impact sled simulations with an FE model representing a THOR average male dummy and matched simulations with a human body model (HBM) representing an elderly car occupant were carried out. The HBM used for this study was the THUMS TUC with modified rib cage, which was developed in SENIORS. The modifications included material and geometry changes aiming to represent an elderly car occupant. The rib fracture risk was predicted with a deterministic approach whereby a rib was considered broken when the strain exceeded an age-dependent threshold. Furthermore, a probabilistic method was applied to predict the probability of sustaining a certain number of fractured ribs by comparing local strain values to the distribution of cortical rib ultimate strain. By relating the output from the HBM simulations to a multi-point dummy injury criterion, injury risk curves were calculated by statistical methods. The wide range of loading conditions resulted in the desired range of injuries and THOR ATD output. The number of fractured ribs predicted by the HBM based on the deterministic prediction method was between 0 and 15. Furthermore, the probabilistic risk for the number of rib fractures equal or greater than two, three or four was calculated for each load case. The THOR rib deflection criterion Rmax was between 18 and 56 mm, while the PC Score was in the range of 2.5 to 7.2. Based on these outputs new risk curves for the predicted deterministic (AIS2+/3+) and probabilistic injury risk were calculated. The new curves show reasonable shapes and significance that provide trust in their application. The new risk curves are compared to risk curves obtained by traditional methods. The results were found similar to previous injury risk functions based on physical tests, which gives a high level of confidence in the chosen approach. The simulation-based approach of matched ATD model vs. HBM simulation was successfully applied. Rmax curves show a slightly better quality than the injury criterion PC Score.
Anhand von zwei verschiedenen Versuchskonfigurationen wurde das Schutzpotential von Kopfschutzsystemen (Fahrradhelm und airbagbasiertes System) untersucht. Hierbei wurden die resultierende Kopfbeschleunigung als Messwert sowie das Kopfverletzungskriterium HIC bei Versuchen ohne und mit Kopfschutzsystem vergleichend gegenübergestellt.
Test and assessment procedures for passive pedestrian protection of passenger cars are in place for many years within world-wide regulations as well as consumer test programmes. Nevertheless, recent accident investigations show a stagnation of pedestrian fatality numbers on European roads alongside increasing injury severities for older road users. The EU-funded SENIORS (Safety ENhancing Innovations for Older Road userS) project developed and evaluated a thorax injury prediction tool (TIPT) for later incorporation within test and assessment procedures. Accident data indicates an increasing portion of AIS2 and AIS3+ thoracic injuries of older pedestrians and cyclists which are currently not assessed in any test procedure for vulnerable road users. Therefore, SENIORS focused on the development of a test tool predicting the risk of rib fractures of vulnerable road users (VRU). While injury risk functions were reanalyzed, human body model (HBM) simulations against categorized generic vehicle frontends served as input for the definition of test setups and corresponding impact parameters. TIPT component tests against a generic frontend and an actual vehicle were used for the evaluation of the technical feasibility. The TIPT component tests shows the general feasibility of a test procedure for the assessment of thoracic injuries, with good repeatability and reproducibility of kinematics and results. Impact parameters such as the inclination angles of the thorax, angles of the velocity vector and impact speeds well replicate the parameters gained from the HBM simulations. The proposed markup and assessment scheme offers the possibility of a homogeneous evaluation of the protection potential of vehicle frontends while maintaining justifiable testing efforts. During evaluation testing, the proposed requirements were entirely met. The developed prototype of TIPT and launching system offer impact angles and speeds as suggested by HBM simulations. However, since thorax impacts during pedestrian accidents do not occur perpendicularly to the vehicle surface in most cases, the TIPT built-in linear potentiometers do not acquire the true resultant intrusions on the ribcage and thus, TIPT rib deflections do not reflect the actual human injury risk. However; for the impact forward to the bonnet leading edge, the TIPT seems applicable without further modifications. The test and assessment procedures using the TIPT offer for the first time the possibility of replicating the kinematics of a pedestrian thorax with a component test. The developed assessment scheme gives a first indication on how the risk for thoracic injuries could be implemented within the Euro NCAP Box 3 assessment. Future development of the TIPT may focus on implementing a rib cage that can deflect in all axes in a humanlike way.
Nach wie vor ist die Anzahl von Unfällen motorisierter Einspurfahrzeuge (MESFz) mit sehr schweren Verletzungsfolgen oder tödlichem Ausgang für die Aufsassen im Vergleich zu allen anderen getöteten Verkehrsteilnehmern alarmierend hoch. Im Jahr 2013 wurden bei insgesamt 42.427 Unfällen MESFz 641 Aufsassen getötet und 12.034 schwer verletzt. Um dieser hohen Zahl schwerverletzter und getöteter Aufsassen von MESFz entgegenzuwirken, hat die Bundesanstalt für Straßenwesen (BASt) das vorliegende Projekt initiiert. Zielsetzung des Projektes war es, durch eine Analyse von Unfalldaten von MESFz, durch ergänzende computergestützte FEM-Simulationen und durch eine kritische Bewertung der UN-Regelung UN-R 22/05 (vormals ECE-R 22/05) hinsichtlich verletzungs-biomechanischer Inhalte (Versuche und Prüfwerte) Erkenntnisse zu erarbeiten, Handlungsbedarf festzustellen und Änderungs- und Ergänzungsvorschläge zur Überarbeitung der UN-R 22/05 sowie hinsichtlich allgemeiner Maßnahmen zu formulieren. Auf der Grundlage der amtlichen Unfalldaten des Statistischen Bundesamtes, Wiesbaden (DESTATIS) erfolgte eine Unfalldatenauswertung im Allgemeinen. Für eine detaillierte Analyse wurden Daten der "German In-Depth Accident Study" (GIDAS, Dresden und Hannover) ausgewählt. Bei etwa der Hälfte der im Teilumfang (n=199) untersuchten Unfälle von MESFz kam es zu Kopfverletzungen, überwiegend bei benutztem Schutzhelm. In 18 % lagen die führenden Verletzungen am Kopf; in 48 % blieb der Kopf unverletzt bei sonstigen schweren bis schwersten und tödlichen Verletzungen am Körper. Etwa 10 % der Aufsassen benutzten ein MESFz ohne bzw. mit absolut ungeeignetem Helm. Eine kritische Bewertung und Alternativvorschläge der derzeitigen Fassung der UN-R 22/05 wurden bezüglich der Punkte Prüfumfang, Prüfausstattung, Prüfdurchführung, Prüfkriterien und eine fälschungssicheren Homologations-Kennzeichnung erarbeitet.
Thorax injury is one of main causes of serious injury in frontal collisions, especially for elderly car occupants. The anthropometric test device (ATD) THOR‐M provides chest deflection measurements at multiple locations, to assess the risk of thorax injury. For this purpose e, risk functions are needed that relate the potential criteria based on multipoint chest deflection measurement to in jury risk. Different thorax injury criteria and risk functions for THOR have been proposed [2‐3]. The criteria and functions are based on the traditional approach to developing injury risk functions using matched ATD and PMHS tests by relating the injury (number of fractures) to injury criteria. Regarding these studies, some limitations have been identified, in particular concerning the loading conditions of the data used (mainly 3‐point‐belt loading, high loading severity, out‐of‐date ATD versions. To extend the data set and overcome these limitations, a new approach for improved thorax injury criteria was applied within the EC‐funded project SENIORS. The new approach is based on matched frontal impact sled computer simulations with a model representing the latest THOR‐M ATD version, and matching simulations with a human body model (HBM) representing an elderly car occupant.
A reduction of around 48% of all road fatalities was achieved in Europe in the past years including a reduced number of fatalities with an older age. However, among all road fatalities, the proportion of elderly is steadily increasing. In an ageing society, the European (Horizon2020) project SENIORS aims to improve the safe mobility of older road users, who have different transportation habits compared to other age groups. To increase their level of safe mobility by determining appropriate requirements for vehicle safety systems, the characteristics of current road traffic collisions involving the elderly and the injuries that they sustain need to be understood in detail. Hereby, the paper focuses on their traffic participation as pedestrian, cyclist or passenger car occupant. Following a literature review, several national and international crash databases and hospital statistics have been analysed to determine the body regions most frequently and severely injured, specific injuries sustained and types of crashes involved, always comparing older road users (65 years and more) with mid-aged road users (25-64 years). The most important crash scenarios were highlighted. The data sources included European statistics from CARE, data on national level from Germany, Sweden, Italy, United Kingdom and Spain as well as in-depth crash information from GIDAS (Germany), RAIDS (UK), CIREN and NASS-CDS (US). In addition, familiar hospital data from Germany (TraumaRegister DGU-®), Italy (Italian Register of Acute Traumas) and UK hospital statistics (TARN) were included in the study to gain further insight into specific injury patterns. Comprehensive data analyses were performed showing injury patterns of older road users in crashes. When comparing with mid-aged road users, all databases showed that the thorax body region is of particularly high importance for the older car occupant with injury severities of AIS 2 or AIS 3+, whereas the body regions lower extremities, head and thorax need to be considered for the older pedestrians and cyclists. Besides these comparisons, the most frequent and severe top 5 injuries were highlighted per road user group. Further, the most important crash configurations were identified and injury risk functions are provided per age group and road user group. Although several databases have been analysed, the picture on the road safety situation of older road users in Europe was not complete, as only Western European data was available. The linkage between crash data and hospital data could only be made on a general level as their inclusion criteria were quite different.
Europe has benefited from a decreasing number of road traffic fatalities. However, the proportion of older road users increases steadily. In an ageing society, the SENIORS project aims to improve the safe mobility of older road users by determining appropriate requirements towards passive vehicle safety systems. Therefore, the characteristics of road traffic crashes involving the elderly people need to be understood. This paper focuses on car occupants and pedestrians or cyclists in crashes with modern passenger cars. Ten crash databases and four hospital statistics from Europe have been analysed to answer the questions on which body regions are most frequently and severely injured in the elderly, and specific injuries sustained by always comparing older (65 years and above) with midâ€aged road users (25â€64 years). It was found that the body region thorax is of particularly high importance for the older car occupant with injury severities of AIS2 or AIS3+, where as the lower extremities, head and the thorax need to be considered for older pedestrians and cyclists. Further, injury risk functions were provided. The hospital data analysis showed less difference between the age groups. The linkage between crash and hospital data could only be made on a general level as their inclusion criteria were quite different.
One main objective of the EU-Project SENIORS is to provide improved methods to assess thoracic injury risk to elderly occupants. In contribution to this task paired simulations with a THOR dummy model and human body model will be used to develop improved thoracic injury risk functions. The simulation results can provide data for injury criteria development in chest loading conditions that are underrepresented in PMHS test data sets that currently proposed risk functions are based on. To support this approach a new simplified generic but representative sled test fixture and CAE model for testing and simulation were developed. The parameter definition and evaluation of this sled test fixture and model is presented in this paper. The justification and definition of requirements for this test set-up was based on experience from earlier studies. Simple test fixtures like the gold standard sled fixture are easy to build and also to model in CAE, but provide too severe belt-only loading. On the other hand a vehicle buck including production components like airbag and seat is more representative, but difficult to model and to be replicated at a different laboratory. Furthermore some components might not be available for physical tests at later stage. The basis of the SENIORS generic sled test set-up is the gold standard fixture with a cable seat back and foot rest. No knee restraint was used. The seat pan design was modified including a seat ramp. The three-point belt system had a generic adjustable load limiter. A pre-inflated driver airbag assembly was developed for the test fixture. Results of THOR test and simulations in different configurations will be presented. The configurations include different deceleration pulses. Further parameter variations are related to the restraint system including belt geometry and load limiter levels. Additionally different settings of the generic airbag were evaluated. The test set-up was evaluated and optimized in tests with the THOR-M dummy in different test configurations. Belt restraint parameters like D-ring position and load limiter setting were modified to provide moderate chest loading to the occupant. This resulted in dummy readings more representative of the loading in a contemporary vehicle than most available PMHS sled tests reported in the literature. However, to achieve a loading configuration that exposes the occupant to even less severe loading comparable to modern vehicle restraints it might be necessary to further modify the test set-up. The new generic sled test set-up and a corresponding CAE model were developed and applied in tests and simulations with THOR. Within the SENIORS project with this test set-up also volunteer and PMHS as well as HBM simulations are performed, which will be reported in other publications. The test environment can contribute in future studies to the assessment of existing and new frontal impact dummies as well as dummy improvements and related instrumentation. The test set-up and model could also serve as a new standard test environment for PMHS and volunteer tests as well as HBM simulations.
Recently, EuroNCAP updated the upper legform test protocols. The main objective of this study is to establish the upper legform test in KIDAS (Korean In-depth Accident Study) taking into account domestic pedestrian accident data as well as anthropometric data to protect elderly pedestrians whose average height and weight is much smaller and lighter than other age groups, especially compared to Europeans. Therefore 230 cases of pedestrian accidents from KIDAS were investigated to explore the injury severity of body regions as well as age related injury patterns. Injuries of all body regions were examined, with a special focus on injuries of abdomen and pelvic area. On the other hand, in order to explore Korea's pedestrian accident environment, national police data and KIDAS (Korean In-depth Accident Study) data were compared. The results should be taken into account in future analyses and possible improvements, such as regulations and KNCAP test protocols, of the pedestrian safety policy in Korea.
The incidence of side impacts was investigated from GIDAS data. Both vehicle-fixed object and vehicle-vehicle collisions were analysed as these are enclosed within the consumer testing program. Vehicle-fixed object collisions were stratified according to ESC availability. Results indicated that vehicles equipped with ESC rarely have pure-lateral impacts. An increase in oblique collisions was seen for the vehicles with ESC whereby most vehicle were driving in left curves. The analysis of vehicle-vehicle collisions developed injury risk curves were developed at the AIS3+ injury severity for the vehicle-vehicle side impacts. Results suggested that greatest injury risk occurred when a Pre Euro NCAP vehicle was struck by a Post Euro-NCAP vehicle. The remaining curves did not show different behaviour, indicating that stiffness increased have been equally combated. This was attributable to the few Post Euro-NCAP vehicles that had a deployed curtain airbag available in the sample. The integration of Euro NCAP testing has shown to improve vehicle crashworthiness for pole collisions, as those vehicles with ESC rarely incur lateral impacts.
Car occupants have a high level of mortality in road accidents, since passenger cars are the prevalent mode of transport. In 2013, car occupant fatalities accounted for 45% of all road accident fatalities in the EU. The objective of this research is the analysis of basic road safety parameters related to car occupants in the European countries over a period of 10 years (2004-2013), through the exploitation of the EU CARE database with disaggregate data on road accidents. Data from the EU Injury Database for the period 2005 - 2008 are used to identify injury patterns, and additional insight into accident causation for car occupants is offered through the use of in-depth accident data from the EC SafetyNet project Accident Causation System (SNACS). The results of the analysis allow for a better understanding of the car occupants' safety situation in Europe, thus providing useful support to decision makers working for the improvement of road safety level in Europe.
In this study, we compared the injury severity of occupants according to the seating position and the crashing direction in motor vehicle accidents. In the driver's point of view, it was separated the seating position as "Near-side" and "Far-side". The study subjects were targeted by people who visited 4 regional emergency centers following motor vehicle accidents. Real-world investigation was performed by direct and indirect methods after patient- consent. The information of the damaged vehicle was informed by Collision Deformation Classification (CDC) code and the information of the injury of patients was informed by using the Abbreviated Injury Score (AIS) and Injury Severity Score (ISS). When the column 3 in CDC code was P, damaged at the middle part of lateral side, the average point of AIS 3 was 1.91-±1.72 in near-side and 1.02-±1.31 in far-side (p<0.01). The average point of maximum AIS (MAIS) was 2.78-±1.39 in near-side and 2.02-±1.11 in far-side (p<0.01). The average point of ISS was 15.74-±14.71 in near-side and 8.11-±8.39 in far-side (p<0.01). Also, when the column 3 in CDC code was D, damaged at the whole part of lateral side, it was significant that the average point of AIS 3 and MAIS in near-side was bigger than in far-side (p=0.02).
Injury probability functions for pedestrians and bicyclists based on real-world accident data
(2017)
The paper is focusing on the modelling of injury severity probabilities, often called as Injury Risk Functions (IRF). These are mathematical functions describing the probability for a defined population and for possible explanatory factors (variables) to sustain a certain injury severity. Injury risk functions are becoming more and more important as basis for the assessment of automotive safety systems. They contribute to the understanding of injury mechanisms, (prospective) evaluation of safety systems and definition of protection criteria or are used within regulation and/or consumer ratings. In all cases, knowledge about the correlation between mechanical behavior and injury severity is needed. IRFs are often based on biomechanical data. This paper is focusing on the derivation of injury probability models from real world accident data of the GIDAS database (German In-depth Accident Study). In contrast to most academic terms there is no explicit term definition or definition of creation processes existing for injury probability models based on empirical data. Different approaches are existing for such kind of models in the field of accident research. There is a need for harmonization in terms of the used methods and data as well as the handling with the existing challenges. These are preparation of the dataset, model assumptions, censored/unknown data, evaluation of model accuracy, definition of dependent and independent variable, and others. In the presented study, several empirical, statistical and phenomenological approaches were analyzed regarding their advantages and disadvantages and also their applicability. Furthermore, the identification of appropriate prediction parameters for the injury severity of pedestrians has been considered. Due to its main effect on injuries of pedestrians and bicyclists, the importance of the secondary impact has also been analyzed. Finally, the model accuracy, evaluated by several criteria, is the rating factor that gives the quality and reliability for application of the resulting models. After the investigation and evaluation of statistical approaches one method was chosen and appropriate prediction variables were examined. Finally, all findings were summarized and injury risk functions for pedestrians in real world accidents were created. Additionally, the paper gives instructions for the interpretation and usage of such functions. The presented results include IRFs for several injury severity levels and age groups. The presented models are based on a high amount of real world accidents and describe very well the injury severity probability of pedestrians and bicyclists in frontal collisions with current vehicles. The functions can serve as basis for the evaluation of effectiveness of systems like Pedestrian-AEB or Bicycle-AEB.
In most of developed countries, the progress made in passive safety during the last three decades allowed to drastically reduce the number of killed and severely injured especially for occupants of passenger cars. This reduction is mainly observed for frontal impacts for which the AIS3+ injuries has been reduced about 52% for drivers and 38% for front passengers. The stiffening of the cars' structure coupled with the generalization of airbags and the improvement of the seatbelt restraint (load limiter, pretension, etc.) allowed to protect vital body regions such as head, neck and thorax. However, the abdomen did not take advantage with so much success of this progress. The objective of this study is to draw up an inventory on the abdominal injuries of the belted car occupants involved in frontal impact, to present adapted counter-measures and to assess their potential effectiveness. In the first part the stakes corresponding to the abdominal injuries will be defined according to types of impact, seat location, occupants' age and type of injured organs. Then, we shall focus on the abdominal injury risk curves for adults involved in frontal impact and on the comparisons of the average risks according to the seat location. In the second part we will list counter-measures and we shall calculate their effectiveness. The method of case control will be used in order to estimate odds ratio, comparing two samples, given by occupants having or not having the studied safety system. For this study, two type of data sources are used: national road injured accident census and retrospective in-depth accident data collection. Abdominal injuries are mainly observed in frontal impact (52%). Fatal or severe abdominal occupant- injuries are observed at least in 27% of cases, ranking this body region as the most injured just after the thorax (51%). In spite of a twice lower occupation rate in the back seats compared to the front seats, the number of persons sustaining abdominal injuries at the rear place is higher than in the front place. In recent cars, the risk of having a serious or fatal abdominal injury in a frontal impact is 1.6% for the driver, 3.6% for the front passenger and 6.3% for the rear occupants. The most frequently hurt organs are the small intestine (17%), the spleen (16%) and the liver (13%). The most common countermeasures have a good efficiency in the reduction of the abdominal injuries for the adults: the stiffness of the structure of the seats allows decreasing the abdominal injury risk from 54% (driver) to 60% (front occupant), the seatbelt pretensioners decrease also this risk from 90% (driver) to 83% (front passenger).
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.
Die Elektromobilität ist nicht erst seit dem Nationalen Entwicklungsplan Elektromobilität der Bundesregierung, der u.a. als Zielsetzung hat, dass eine Million Elektrofahrzeuge bis 2020 auf deutschen Straßen fahren sollen, ein allgegenwärtiges Thema. Eine zu lösende Aufgabe auf dem Weg zu diesem Ziel ist die Betrachtung der Abhängigkeiten der Systeme Elektrofahrzeug, Ladeverbindungseinheit und Ladesystem, welche bisher weitgehend autonom normiert sind. Um Personen- und Sachschäden beim Laden von Fahrzeugen zu vermeiden, ist es möglicherweise erforderlich, Anforderungen an die Sicherheit dieses Gesamtsystems zu definieren. Zu diesem Zweck beauftragte die Bundesanstalt für Straßenwesen die SGS-TÜV Saar GmbH, Competence Center Funktionale Sicherheit mit der Durchführung einer Risikoanalyse, mit dem Ziel die Sicherheitsaspekte beim Laden eines Elektrofahrzeuges zu untersuchen. Bisher nicht bzw. unzureichend betrachtete Gefährdungen während des Ladevorganges sollten aufgezeigt werden. Nötige Maßnahmen sollten definiert und punktuell mittels Tests validiert werden, um identifizierte Risiken auf ein ausreichend geringes Maß zu senken. Im Kern wurde untersucht, welche potenziellen Risiken (Das Risiko definiert sich als die Beschreibung eines Ereignisses mit der Möglichkeit negativer Auswirkungen. Das Risiko wird allgemein als Produkt aus Eintrittswahrscheinlichkeit eines Ereignisses und dessen Konsequenz angesehen. (Quelle: Wikipedia)) beim Laden eines Elektrofahrzeugs auftreten. Auf Basis einer Normenrecherche wurde die Frage beantwortet, an welchen Stellen normativer und gesetzlicher Handlungsbedarf besteht. Dazu wurden die nachfolgenden Schwerpunkte erarbeitet: - Darstellung möglicher sicherheitskritischer Bedingungen beim Laden; - Zuordnung der sicherheitskritischen Bedingungen zu den Subsystemen Infrastruktur, Kabel und Fahrzeug; - Definition von Maßnahmen zur Erhöhung der Sicherheit beim Laden; - Aufzeigen der Zuständigkeiten für die Gewährleistung der Sicherheit; - Offenlegung des regelungsseitigen Bedarfs. Im ersten Schritt wurde eine Risikoanalyse durchgeführt, um die potenziellen Risiken beim Laden eines Elektrofahrzeugs aufzuzeigen. Die Risikoanalyse wurde zunächst ohne Berücksichtigung bereits normativ oder gesetzlich festgelegter Schutzmaßnahmen durchgeführt. Anschließend erfolgte eine iterative Weiterführung der Betrachtung der Risiken in zweierlei Hinsicht: a) Berücksichtigung existierender normativer und/ oder gesetzlicher Anforderungen, welche parallel zur Risikoanalyse recherchiert wurden; b) Beschreibung ergänzender technischer und/ oder organisatorischer Maßnahmen, um nicht abgedeckte Risiken weiter zu reduzieren. Danach wurde eine erneute Beurteilung der Risiken vorgenommen, um aufzuzeigen, ob die vorhandenen bzw. neu definierten Maßnahmen in der Lage sind, das identifizierte Risiko in ausreichendem Maß zu reduzieren. Generell zeigte sich im Rahmen der Risikoanalyse eine breite, durch Normen und Richtlinien bzw. gesetzlichen Regelungen, vorhandene Abdeckung der möglichen Risiken. Derzeit nicht abgedeckte Risiken konnten adressiert und wirksame Lösungsmöglichkeiten vorgeschlagen werden. Bei Umsetzung aller aufgezeigten Lösungsansätze bleiben somit keine relevanten Risiken offen. Jedoch zeigt sich auch, dass zu bestimmten Themen dringender Handlungsbedarf besteht. Als Ergebnis ließ sich zu folgenden Punkten ein konkreter Handlungsbedarf ableiten: - Als eines der Hauptrisiken wurde das Laden an einer haushaltsüblichen Schukosteckdose, ohne die Nutzung einer zusätzlichen in der Ladeleitung integrierten Schutzeinrichtung, identifiziert. Bei Ladeleitungen mit Schutzeinrichtung hängt deren Schutzwirkung nicht zuletzt von einer regelmäßigen technischen Überprüfung ab; - Als relevant wurden weiterhin die elektromagnetischen Felder, die von einer Ladeleitung bei hohen Strömen ausgehen (zukünftige Schnellladesysteme), identifiziert, hier sind tiefergehende Untersuchungen erforderlich; Im Sinne der Risikominimierung sollte auch das maximal zulässige Gewicht der Ladegarnitur limitiert sein; - Auch Risiken, die sich durch die Bedienung ergeben, wurden untersucht. Mit entsprechenden Hinweisen im Bedienungshandbuch des Elektrofahrzeuges kann hier bereits einigen möglichen Gefahren begegnet werden. Dies betrifft unter anderem die Handhabung der Ladegarnitur beim Laden im öffentlichen Raum. Aus den ermittelten, noch umzusetzenden Maßnahmen geht hervor, dass der derzeitige Stand der Normung und gesetzlichen Regelungen noch nicht vollkommen ausreichend ist, um alle ermittelten und aufgezeigten Risiken in ausreichendem Maße zu reduzieren. Aus den Ergebnissen der Studie wird aber auch deutlich, dass die Sicherheit nicht alleine von einem Teilsystem alleine, sondern vielmehr durch das sichere Zusammenwirken aller Teile, auch in Kombination mit dem Verhalten der Nutzer und partizipierender Personen, gewährleistet wird.
Road accidents are typically analyzed to address influences of human, vehicle, and environmental (primarily infrastructure) factors. A new methodology, based on a "Venn diagram" analysis, gives a broader perspective on the probable factors, and combinations of factors, contributing both to the occurrence of a crash and to sustaining injuries in that crash. The methodology was applied to 214 accidents on the Mumbai-Pune expressway. Factors contributing to accidents and injuries were addressed. The major human factors influencing accidents on this roadway were speeding (30%) and falling asleep (29%), while injuries were primarily due to lack of seat belt use (46%). The leading infrastructure factor for injuries was impact with a roadside manmade structure (28%), and the main vehicle factor for injuries was passenger compartment intrusion (73%). This methodology can help identify effective vehicle and infrastructure-related solutions for preventing accidents and mitigating injuries in India.
This study aimed at prediction of long bone fractures and assessment of lower extremity injury mechanisms in real world passenger car to pedestrian collision. For this purpose, two pedestrian accident cases with detail recorded lower limb injuries were reconstructed via combining MBS (Multi-body system) and FE (Finite element) methods. The code of PC Crash was used to determine the boundary conditions before collision, and then MBS models were used to reproduce the pedestrian kinematics and injuries during crash. Furthermore, a validated lower limb FE model was chosen to conduct reconstruction of injuries and prediction of long bone fracture via physical parameters of von Mises stress and bending moment. The injury outcomes from simulations were compared with hospital recorded injury data and the same long bone fracture patterns and positions can be observed. Moreover, the calculated long bone fracture tolerance corresponded to the outcome from cadaver tests. The result shows that FE model is capable to reproduce the dynamic injury process and is an effective tool to predict the risk of long bone fractures.
Frontal impact is still the most relevant impact direction in terms of injury causation amongst car occupants. Especially for car-to-car frontal impacts the mass ratio between the involved vehicles has a significant impact on the injury risk (the heavier the opponent car the higher the injury risk). In order to address this issue frontal Mobile Deformable Barrier test procedures have been developed world-wide (for example the MPDB procedure that was fully described during the FIMCAR Project). The objective of this study was to investigate how vehicles of different weight classes perform in a mobile barrier test procedure compared to a fixed barrier test procedure (the full width rigid and offset deformable barrier test). Beyond that, the influence of vehicle mass and vehicle deformation on injuries was evaluated based on real world accident data. Five vehicle types were selected and tested in a fixed offset test procedure (ODB), a full width rigid barrier test procedure (FWRB) and a mobile offset test procedure (MPDB). For the accident analyses data from the German In-Depth Accident Study (GIDAS) was evaluated with a focus on MAIS 2+ injured belted front row car (UN-R 94 compliant cars) occupants in frontal impact accidents. Test data indicates higher dummy loadings, in particular for the head acceleration and chest acceleration, in the MPDB test for the vehicles with a mass lighter than the trolley (1,500 kg) compared to the FWRB test. The trend of increased vehicle stiffness (especially illustrated by tests with the MPDB and small cars) shows the need of a further improvement of passive restraint systems to reduce the occupant loading and with it the injury risk. The analyzed GIDAS data confirm the higher injury risk for occupants in cars with an accident weight of less than 1,500 kg compared to those with a crash weight above 1,500 kg in car-to-car and car-to-object or car-to-HGV, respectively. Furthermore the injury risk increases with decreasing mass ratio (i.e., the opponent car is heavier) in car-to-car accidents. Independent from the higher injury risk, the risk for passenger compartment intrusion in frontal impact appears not to be independent on the crash weight of the car.
In North America, frontal crash tests in both the regulatory environment and consumer-based safety rating schemes have historically been based on full-width and moderate-overlap (40%) vehicle to barrier impacts. The combination of improved seat-belt technologies, notably belt tensioning and load limiting systems, together with advanced airbags, has proven very effective in providing occupant protection in these crash modes. Recently, however, concern has been raised over the contribution of narrower frontal impacts, involving primarily the vehicle corners, to the incidence of fatality and serious injury as a result of the potential for increased occupant compartment intrusion and performance limitations of current restraint systems. Drawing on data documented in the National Automotive Sampling System (NASS)/ Crashworthiness Data System (CDS) for calendar years 1999 to 2012, the present study examines the characteristics of existing and proposed corner crash test configurations, and the nature of real-world collisions that approximate the test environments. In this analysis, particular emphasis is placed on crash pulse information extracted from vehicle-based event data recorders (EDR's).
This study aimed at developing an injury estimation algorithm for AACN technologies for Germany and compared them to findings based on Japanese data. The data to build and to verify the algorithm was obtained from the German in-depth Accident Database (GIDAS) and split into a training and a validation dataset. Significant input variables and the generalized linear regression model to predict severe injuries (ISS>15) were selected to maximize area under the receiver operating characteristic curve (AUC). Probit regression with the input parameter multiple impact, delta v, seatbelt use and impact direction gave the largest AUC of 0.91. Sensitivity of the algorithm was validated at 90% and specificity at 76% for an injury risk threshold of 2%. It appears that no major differences between Japan and Germany exist for injury estimation based on delta v and impact direction. However, far side impact and multiple crash events appear to be associated with a larger risk increase in the German data.
Analysis of pedestrian leg contacts and distribution of contact points across the vehicle front
(2015)
Determining the risk to pedestrians that are impacted by areas of the front bumper not currently regulated in type-approval testing requires an understanding of the target population and the injury risk posed by the edges of the bumper. National statistics show that approximately 10% of all accident casualties are pedestrians, with 20% to 30% of these pedestrian casualties being killed or seriously injured. However, the contact position across the front of the bumper is not recorded in national statistics and so in-depth accident databases (OTS, UK and GIDAS, Germany) were used to examine injury risk in greater detail. The results showed that some injury types and severities of injuries appear to peak around the bumper edges. Although there are sometimes inconsistencies in the data, generally there is no evidence to suggest that the edges of the bumper are less likely to be contacted or cause injury.
Autonomous Emergency Braking (AEB) systems for pedestrians have been predicted to offer substantial benefit. On this basis, consumer rating programmes, e.g. Euro NCAP, are developing rating schemes to encourage fitment of these systems. One of the questions that needs to be answered to do this fully, is to determine how the assessment of the speed reduction offered by the AEB is integrated with the current assessment of the passive safety for mitigation of pedestrian injury. Ideally, this should be done on a benefit related basis. The objective of this research was to develop a benefit based methodology for assessment of integrated pedestrian protection systems with pre-crash braking and passive safety components. A methodology has been developed which calculates the cost of pedestrian injury expected, assuming all pedestrians in the target population (i.e. pedestrians impacted by the front of a passenger car) are impacted by the car being assessed, taking into account the impact speed reduction offered by the car’s AEB (if fitted) and the passive safety protection offered by the car’s frontal structure. For rating purposes, this cost can be normalised by comparing it to the cost calculated for selected cars. The methodology uses the speed reductions measured in AEB tests to determine the speed at which each casualty in the target population will be impacted. The injury to each casualty is then calculated using the results from standard Euro NCAP pedestrian impactor tests and injury risk curves. This injury is converted into cost using ‘Harm’ type costs for the body regions tested. These costs are weighted and summed. Weighting factors were determined using accident data from Germany and GB and the results of a benefit analysis performed by the EU FP7 AsPeCSS project. This resulted in German and GB versions of the methodology. The methodology was used to assess cars with good, average and poor Euro NCAP pedestrian ratings, with and without a current AEB system fitted. It was found that the decrease in casualty injury cost achieved by fitting an AEB system was approximately equivalent to that achieved by increasing the passive safety rating from poor to average. Also, it was found that the assessment was influenced strongly by the level of head protection offered in the scuttle and windscreen area because this is where head impact occurs for a large proportion of casualties. The major limitation within the methodology is the assumption used implicitly during weighting. This is that the cost of casualty injuries to body areas, such as the thorax, not assessed by the headform and legform impactors, and other casualty injuries such as those caused by ground impact, are related linearly to the cost of casualty injuries assessed by the impactors. A methodology for assessment of integrated pedestrian protection systems was developed. This methodology is of interest to consumer rating programmes which wish to include assessment of these systems. It also raises the interesting issue if the head impact test area should be weighted to reflect better real-world benefit.
During the past five years, a Euro NCAP technical working group on pedestrian safety has been working on improving test and assessment procedures for enhanced passive pedestrian safety. After harmonizing the tools and procedures as much as possible with legislation, the work was mainly focused on the development of grid procedures for the pedestrian body regions head, upper leg with pelvis and lower leg with knee. Furthermore, the test parameters for the head and the upper leg were revised, a new lower legform impactor was introduced and the injury thresholds were adjusted or, where necessary, the injury criteria were changed. Finally, the assessment limits and colour scheme were refined, widening the range and adding two more colours in order to provide a more detailed description of the pedestrian safety performance. By abstaining from an assessment based on a worst point selection philosophy, the improved test point determination procedures that were introduced during the years 2013 and 2014 give a more homogeneous, high resolution picture of the pedestrian safety performance of the vehicle frontends. By using a uniform grid for each test zone approximately 200 test points, evenly distributed within each area, can now be assessed per vehicle. The introduction of the flexible pedestrian legform impactor in 2014 enables a more realistic injury prediction of the knee and the tibia using a biofidelic test tool. With the new upper legform test that has been launched in 2015 the assessment in that area is now focusing on the injured body region instead of the injury causing vehicle part and thus is aligned with the approach in the remaining body regions head and lower leg. At the same time, a monitoring test with the headform impactor against the bonnet leading edge is closing the possible gap between the test areas to identify injury causing vehicle parts that moved out of focus due to the introduction of the new upper legform test. The paper describes the new test and assessment procedures with their underlying philosophy and gives an outlook in terms of open issues, specifying the needs for further improvement in the future. In parallel to the work of the pedestrian subgroup, a Euro NCAP working group on heavy vehicles introduced a set of protocol changes in 2011 that were related to the assessment of M1 vehicles derived from commercial vehicles, with a gross vehicle weight between 2.5 and 3.5 tons and 8 or 9 seats. The paper also investigates the applicability of the new pedestrian test and assessment procedures to heavy vehicles.
To improve vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility aims to improve both the self and partner protection properties of vehicles. Although compatibility has received worldwide attention for many years, no final assessment approach has been defined. Within the Frontal Impact and Compatibility Assessment Research (FIMCAR) project, different frontal impact test procedures (offset deformable barrier [ODB] test as currently used for Economic Commission for Europe [ECE] R94, progressive deformable barrier test as proposed by France for a new ECE regulation, moveable deformable barrier test as discussed worldwide, full-width rigid barrier test as used in Federal Motor Vehicle Safety Standard [FMVSS] 208, and full-width deformable barrier test) were analyzed regarding their potential for future frontal impact legislation. The research activities focused on car-to-car frontal impact accidents based on accident investigations involving newer cars. Test procedures were developed with both a crash test program and numerical simulations. The proposal from FIMCAR is to use a full-width test procedure with a deformable element and compatibility metrics in combination with the current offset test as a frontal impact assessment approach that also addresses compatibility. By adding a full-width test to the current ODB test it is possible to better address the issues of structural misalignment and injuries resulting from high acceleration accidents as observed in the current fleet. The estimated benefit ranges from a 5 to 12 percent reduction of fatalities and serious injuries resulting from frontal impact accidents. By using a deformable element in the full-width test, the test conditions are more representative of real-world situations with respect to acceleration pulse, restraint system triggering time, and deformation pattern of the front structure. The test results are therefore expected to better represent real-world performance of the tested car. Furthermore, the assessment of the structural alignment is more robust than in the rigid wall test.
The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx. However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My. The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was observed. It was also observed that the primary neck response in these tests was flexion, not extension. This correlates well with recent findings from Japan and the United States showing a correlation between neck flexion and injury in accident replication simulations and postmortem human subjects (PMHS) studies, respectively. The present certification tests may not adequately control front cervical spine bumper characteristics, which are important for neck flexion response. The certification sled test also does not include the pelvis and so cannot be used to control pelvis response and does not substantially load the lumbar bumpers and so does not control these parts of the dummy. The stiffness of all spine bumpers and of the pelvis flesh should be much more tightly controlled. It is recommended that a method for certifying the front cervical bumpers should be developed. Recommendations are also made for tighter tolerance on the input parameters for the existing certification tests.
Real world accident reconstruction with the Total Human Model for Safety (THUMS) in Pam-Crash
(2013)
Further improvement of vehicle safety needs detailed analysis of real world accidents. According to GIDAS (German In-Depth Accident Study) most car to car front accidents occur at mid-crash severity. In this range thoracic injuries already occur. In this study a real world frontal crash with mid-crash severity out of the AARU database was reconstructed. The selected car to car accident was reconstructed by AARU by means of pc-crash software in order to get the initial dynamic accident conditions. These initial conditions were used to reconstruct the complete accident in more detail using FE models for the car structure and the occupants. Occupant simulations were performed with FE HIII-dummy models and the THUMS using Pam-Crash code. An initial THUMS validation was performed in order to verify the model-´s biofidelity by means of table-top test simulations. THUMS bone stiffness values were modified to match the real word occupant age. A comparison between driver and passenger restraint system loading was done, as well as an injury prediction comparison between the HIII-dummy model and THUMS response for both cases. Detailed comparison between the HIII-dummy models and THUMS regarding thoracic loading are discussed.
In general the passive safety capability is much greater in newer versus older cars due to the stiff compartment preventing intrusion in severe collisions. However, the stiffer structure which increases the deceleration can lead to a change in injury patterns. In order to analyse possible injury mechanisms for thoracic and lumbar spine injuries, data from the German Inâ€Depth Accident Study (GIDAS) were used in this study. A twoâ€step approach of statistical and caseâ€byâ€case analysis was applied for this investigation. In total 4,289 collisions were selected involving 8,844 vehicles, 5,765 injured persons and 9,468 coded injuries. Thoracic and lumbar spine injuries such as burst, compression or dislocation fractures as well as soft tissue injuries were found to occur in frontal impacts even without intrusion to the passenger compartment. If a MAIS 2+ injury occurred, in 15% of the cases a thoracic and/or lumbar spine injury is included. Considering AIS 2+ thoracic and lumbar spine, most injuries were fractures and occurred in the lumbar spine area. From the case by case analyses it can be concluded that lumbar spine fractures occur in accidents without the engagement of longitudinals, lateral loading to the occupant and/or very severe accidents with MAIS being much higher than the spine AIS.
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
The misuse of CRS (child restraint system) is one of the most urgent problems in connection of child safety in cars. Numerous field studies show that more than two thirds of all CRS are used in a wrong way. This misuse could lead to serious injuries for the children. Surprisingly the quality of CRS use is coded much better in accident data (e.g. GIDAS) than the results of observatory field studies show. It is expected that misuse of CRS was not detected by the accident teams in a large number of the cases. An essential part in improving child seats and their usability is the knowledge of the relation between misuse and resulting injuries. For that the analysis and experimental reconstruction of accidents is an important part. For allowing an exact experimental accident reconstruction, it is necessary to have detailed information about the securing situation of the child and about the installation of the CRS in the car.
A series of drop tests and vehicle tests with the adult head impactor according to Regulation (EC) 631/2009 and drop tests with the phantom head impactor according to UN Regulation No. 43 have been carried out by the German Federal Highway Research Institute (BASt) on behalf of the German Federal Ministry of Transport, Building and Urban Development (BMVBS). Aim of the test series was to study the injury risk for vulnerable road users, especially pedestrians, in case of being impacted by a motor vehicle in a way described within the European Regulations (EC) 78/2009 and (EC) 631/2009. Furthermore, the applicability of the phantom head drop test described in UN Regulation No. 43 for plastic glazing should be investigated. In total, 30 drop tests, thereof 18 with the adult head impactor and 12 with the phantom head impactor, and 49 vehicle tests with the adult head impactor were carried out on panes of laminated safety glass (VSG), polycarbonate (PC) and laminated polycarbonate (L-PC). The influence of parameters such as the particular material properties, test point locations, fixations, ambient conditions (temperature and impact angle) was investigated in detail. In general, higher values of the Head Injury Criterion (HIC) were observed in tests on polycarbonate glazing. As the HIC is the current criterion for the assessment of head injury risk, polycarbonate glazing has to be seen as more injurious in terms of vulnerable road user protection. In addition, the significantly higher rebound of the head observed in tests with polycarbonate glazing is suspected to lead to higher neck loads and may also cause higher injury risks in secondary impacts of vulnerable road users. However, as in all tests with PC glazing no damage of the panes was observed, the risk of skin cut injuries may be expected to be reduced significantly. The performed test series give no indication for the test procedure prescribed in UN Regulation No. 43 as a methodology to approve glass windscreen not being feasible for polycarbonate glazing, as all PC panes tested fulfilled the UN R 43 requirements. The performance of the windscreen area will not be relevant for vehicle type approval according to the upcoming UN Regulation for pedestrian protection. However, it is recommended that pedestrian protection being considered for plastic windscreens to ensure at least the same level of protection as glass windscreens.
Mit der flächendeckenden Einführung des Beifahrerairbags ergab sich das Problem der nachträglich festgestellten Inkompatibilität mit rückwärts gerichten Kindersitzen. Zahlreiche tödliche Unfälle mit Babyschalen, insbesondere in den USA, führten unter anderem dazu, dass in den Mitgliedsstaaten der Europäischen Union die Beförderung von Kindern in einem rückwärtsgerichteten Kinderschutzsystem auf einem mit Frontairbag geschützten Autositz untersagt wurde, sofern der Airbag nicht deaktiviert wurde. Heute gibt es eine Vielzahl an Möglichkeiten, die dem Nutzer zur Abschaltung des Airbags zur Verfügung stehen. Mit der Notwendigkeit der Abschaltung ergibt sich die Gefahr zweier Arten der Fehlbenutzung: die Beförderung eines Kindes in einer Babyschale trotz aktivierten Airbags beziehungsweise die Mitfahrt eines erwachsenen Insassen trotz deaktivierten Airbags. Im Rahmen dieser Studie wurden zu den beiden Fehlbenutzungsarten Beobachtungs- und Befragungsstudien durchgeführt, Unfalldaten in Hinblick auf die Problematik der Fehlbenutzung der Airbagabschaltung analysiert und Versuche zur erneuten Bewertung des Risikos, das durch heutige und zukünftige Airbagsysteme ausgeht, durchgeführt. In den Umfragen ließen sich nur schwer Daten zum Missbrauch bei der Beförderung von Kindern mit Airbag auf dem Beifahrersitz erfassen. Es kommt insgesamt zu nur wenigen Fällen des Transports eines Kindes auf dem Beifahrersitz mit aktivem Airbag, was zum einen an der hohen Abschaltquote des Beifahrerairbags liegt, zum anderen an der Präferenz der Eltern, die Kinder auf dem Rücksitz zu transportieren. Der Großteil dieser Fehlbenutzungsfälle entsteht in älteren Pkw, die einen Werkstattaufenthalt für die Deaktivierung/Aktivierung erfordern. Keine Missbräuche beziehungsweise technische Fehler fanden sich bei den Systemen mit automatischer Sitzerkennung. Der überwiegende Anteil der Missbrauchsfälle bei den Modellen mit manueller Umschaltmöglichkeit geht offenbar auf Vergessen zurück. Der Missbrauch zweiter Art wird ebenfalls wirkungsvoll durch automatische Systeme verhindert. Bei dieser Beförderungskonstellation ergibt sich jedoch praktisch immer ein Problem, wenn der Beifahrerairbag in einer Werkstatt deaktiviert wurde. Die dadurch für einen erwachsenen Mitfahrer entstehende Gefährdung wird als weniger gravierend eingeschätzt. Bei der manuellen Umschaltung im Fahrzeug verbleibt ebenfalls ein Vergessensproblem wie beim Missbrauch erster Art. Auch die Unfallanalyse deutet auf eine geringe Fehlbenutzungsquote hin. Von den untersuchten GIDAS-Frontalaufprallunfällen mit über 300 betroffenen Kindern nutzten lediglich 24 Kinder den Beifahrerplatz in einem Auto, das mit einem Beifahrerairbag ausgestattet war. In den meisten Fällen war der Airbag vorschriftsmäßig deaktiviert. In den nachgewiesenen Fehlbenutzungsfällen waren die Unfallfolgen für die betroffenen Babys gering. Die untersuchten Einzelfälle zeigen jedoch die tödliche Gefahr, die vom Beifahrerairbag ausgehen kann. Auf der technischen Seite gab es im Lauf der letzten Jahre grundsätzliche Veränderungen im Bereich der Gestaltung des Beifahrerairbags. Während bei der früheren Einbauposition des Airbags die Schale direkt angeschossen wurde, entfaltet sich dieser heutzutage eher nach oben, stützt sich an der Windschutzscheibe ab und kommt danach erst mit der Schale in Kontakt. Da er in diesem Zustand aber schon weitestgehend voll entfaltet ist, besitzt er zu diesem Zeitpunkt kaum noch die Aggressivität, die bei den Beifahrerairbags der ersten Generation beobachtet werden konnte, und stellt somit wahrscheinlich eine geringere Gefahr für das Kleinkind in der Babyschale dar. Damit lässt sich ein deutlicher Trend in Richtung weniger gefährlicher Airbags erkennen. Der Originalbericht enthält als Anhänge den Abdruck des Expertenfragebogen, die Zusammenfassung der Expertenbefragung, den Umdruck der Online-Befragung sowie den Fragebogen der Feldbefragung "Kindersitze und Airbag auf dem Beifahrersitz". Auf die Widergabe dieser Anhänge wurde in der vorliegenden Veröffentlichung verzichtet. Sie liegen bei der Bundesanstalt für Straßenwesen vor und sind dort einsehbar. Verweise auf die Anhänge im Berichtstext wurden zur Information des Lesers beibehalten.
Straßenseitige Fahrzeug-Rückhaltesysteme haben entsprechend der Richtlinie für passiven Schutz an Straßen durch Fahrzeug-Rückhaltesysteme (RPS) die Aufgabe, die Folgen von Verkehrsunfällen so gering wie möglich zu halten. Sie kommen dabei sowohl zum Schutz unbeteiligter Personen, des Gegenverkehrs bei zweibahnigen Straßen sowie schutzbedürftiger Bereiche neben der Straße als auch zum Schutz der Fahrzeuginsassen vor schweren Folgen infolge Abkommens von der Fahrbahn zum Einsatz. Vor dem Einsatz der unterschiedlichen Systeme muss die Wirksamkeit des jeweiligen Systems für den entsprechenden Anwendungsfall nachgewiesen werden. Dabei regeln die RPS, welche Anforderungen an welchen örtlichen Gegebenheiten erfüllt sein müssen. In DIN EN 1317 sind die zugehörigen Prüfverfahren beschrieben. Da ein normiertes Prüfverfahren nicht alle real auftretenden Unfallszenarien abdecken kann, stellte sich die Frage, wie sich Stahlschutzplanken und Betonschutzwände beim großwinkligen Anprall kleiner und leichter Fahrzeuge verhalten und wie es um die Insassensicherheit bestellt ist. Eine im Rahmen des resultierenden Forschungsprojektes durchgeführte Analyse des Unfallgeschehens ergab für das Jahr 2007 die Zahl von 25.038 polizeilich registrierten Unfällen mit Anprall gegen eine Schutzeinrichtung [Statistisches Bundesamt]. Angaben zu Anprallwinkel, Kollisionsgeschwindigkeit und Fahrzeugmasse können dieser Statistik nicht entnommen werden. Für die In-depth-Analyse wurden daher 69 Unfallgutachten zu Kollisionen mit großem Anprallwinkel (≥ 25-°) aus der DEKRA-Unfalldatenbank herangezogen. Der Schwerpunkt wurde dabei auf 39 Unfälle gelegt, die sich auf Bundesautobahnen ereignet hatten. Mit zunehmendem Anprallwinkel nahm die Unfallhäufigkeit ab. Der größte Winkel lag bei 60-°. Die Masse der anprallenden Fahrzeuge lag zwischen 750 kg und 1.935 kg. Auffällig war die Häufung von Schleuderunfällen. In 29 Fällen kam es zu einem prekollisionären Schleudervorgang. Die Analyse des Unfallgeschehens hat so gezeigt, dass Anpralle gegen passive Schutzeinrichtungen auf Bundesautobahnen mit zunehmendem Anprallwinkel seltener werden und dass der in der Norm für die Systemprüfung geforderte Maximalwinkel von 20-° das Gesamtunfallgeschehen sehr gut abdeckt. Auf Basis der gewonnenen Ergebnisse erfolgte die Festlegung einer Crash-Test-Konfiguration zur Erlangung von Erkenntnissen über die Insassensicherheit bei großwinkligen Anprallen. Dabei wurde als Grundlage der Anprallversuch TB 11 verwendet, wobei der Anprallwinkel von 20-° auf 45-° erhöht wurde. Die Kollisionsgeschwindigkeit von 100 km/h sowie die Fahrzeugmasse von 900 kg blieben unverändert. Die Anpralltests erfolgten gegen eine simulierte Ortbetonwand sowie gegen eine Stahlschutzplanke vom Typ Super-Rail-®. Die Versuchsfahrzeuge waren typgleich mit den Modellen, die für die ursprüngliche TB-11-Prüfung der Systeme verwendet wurden. Die Versuche haben gezeigt, dass beide Systeme die Rückhaltung der anprallenden Fahrzeuge sicher gewährleisteten. Für die Fahrer beider Fahrzeuge hätte aber keine Überlebenschance bestanden. Über das Schutzniveau der Fahrzeuginsassen entscheiden bei derartigen Anprallkonstellationen letztendlich das Niveau der passiven Sicherheit der anprallenden Fahrzeuge sowie das Energieabsorptionsvermögen der die Fahrgastzelle umschließenden Strukturen.
Falltests zur Untersuchung der Belastungen von Dummys beim Aufprall auf den Boden, Teil 1 und 2
(2010)
Beim Zusammenprall eines Motorrads mit einem Pkw unterscheidet man in der Unfallforschung sowohl den Erstanprall des Motorradfahrers an den Pkw als auch den Sekundäraufprall des Motorradfahrers auf dem Boden. So genannte Full-Scale-Crashtests mit Dummys haben beim Erstanprall gezeigt, dass Motorradfahrer durch Airbags potenziell geschützt werden können. Bei den entsprechenden Unfallsimulationen wurde jedoch im weiteren Bewegungsablauf beim nachfolgenden Sekundäraufprall auf dem Boden festgestellt, dass relativ hohe Belastungen auf den Dummy einwirken. Es stellt sich hierbei jedoch die Frage, ob die üblicherweise für Lasteinwirkungen im Falle eines Erstanpralls entwickelten und validierten Dummys die bei einem Sekundäraufprall auf einen Motorradfahrer einwirkenden Belastungen hinreichend genau wiedergeben können. Dazu wurden die Belastungen eines Dummys beim Aufprall auf den Boden untersucht, um das Verletzungsrisiko eines menschlichen Motorradfahrers einschätzen zu können. Im Dekra-Crash-Test-Center wurden vier verschiedene Aufprallsituationen mit einem Hybrid III Dummy durchgeführt, wobei diese Tests an eine andere Testreihe angelehnt sind, die bereits am US-amerikanischen Institut "Dynamic Research International" (DRI) durchgeführt worden waren. Nach der Erläuterung des Testaufbaus und seiner Durchführung wird detailliert auf die gemessenen Verzögerungsbelastungen des Dummys eingegangen. Hierbei geben zum einen Tabellen eine Übersicht über charakteristische Messwerte zur Quantifizierung der maximalen Belastung des Dummys, zum anderen veranschaulichen Bilder die zugehörigen zeitlichen Verzögerungsverläufe in Becken, Brust und Kopf des Dummys. Der Artikel schließt mit einer Interpretation der Versuchsergebnisse und gibt einen Ausblick auf den weiteren Untersuchungsbedarf.
Estimation of the benefits for the UK for potential options to modify UNECE Regulation No. 95
(2010)
The side impact problem in Europe remains substantial. UK data shows that between 22% and 26% of car occupant casualties are involved in a side impact, but this rises to between 29% and 38% for those who are fatally injured. This indicates the more injurious nature of side impacts compared with frontal impacts. The European Enhanced Vehicle safety Committee (EEVC) has performed work to address the side impact issue since 1979. As part of its continuing work, it has recently investigated potential options for regulatory changes to improve side impact protection in cars further. To support this work the UK undertook an analysis to estimate the benefit for potential options to modify UNECE Regulation 95. The analysis used the UK national STATS19 and detailed Co-operative Crash Injury Study (CCIS) accident databases. Of the potential options reviewed, it was found that the addition of a pole test offered the greatest benefit.
Females sustain Cervical Spine Distortion injury (CSD) more often than males. Most work dealing with the biomechanics background (e.g. injury mechanism/criteria) as well as the application in seat design/testing, focuses on the occupant model of an average male. Therefore the EU-Project ADSEAT (Adaptive Seat to Reduce Neck Injuries for Female and Male Occupants) is aimed at adding a female model for gender balanced research of CSD and improving seat design. An extensive literature review, searching for risk factors and injury criteria for males and females, was accompanied by the evaluation of different databases containing CSD cases. The database evaluations suggests that an anthropometry quite close to the 50%ile female anthropometry as known from crash test dummy design is appropriate. The results presented here form the basis for the future development of a computational female model and the improvement of seat design for better protection of both males and females in the frame of the ADSEAT-Project.
The paper presents a methodology for the benefit estimation of several secondary safety systems for pedestrians, using the exceptional data depth of GIDAS. A total of 667 frontal pedestrian accidents up to 40kph and more than 500 AIS2+ injuries have been considered. In addition to the severity, affected body region, exact impact point on the vehicle, and the causing part of every injury, the related Euro NCAP test zone was determined. One results of the study is a detailed impact distribution for AIS2+ injuries across the vehicle front. It can be stated, how often a test zone or vehicle part is hit by pedestrians in frontal accidents and which role the ground impact plays. Basing on that, different secondary safety measures can be evaluated by an injury shift method concerning their real world effectiveness. As an example, measures concerning the Euro NCAP pedestrian rating tests have been evaluated. It was analysed which Euro NCAP test zones are the most effective ones. In addition, real test results have been evaluated. Using the presented methodology, other secondary safety like the active bonnet (pop-up bonnet) or a pedestrian airbag measures can be evaluated.
Werden die in Deutschland gebräuchlichen Stahlschutzplanken umgestaltet um das Verletzungsrisiko für Motorradfahrer zu verringern, zeigt sich ein Kompatibilitätsproblem: Die Erhöhung der Sicherheit für Motorradfahrer wird mit Einschränkungen der Sicherheit von Pkw-Insassen erkauft. Um dieses Kompatibilitätsproblem zu lösen wurden unter Federführung der Bundesanstalt für Straßenwesen (BASt) neue Nachrüstkomponenten für Stahlschutzplanken entwickelt. Dabei lag der Schwerpunkt auf der Senkung der Verletzungsschwere für Motorradfahrer. Im vorliegenden Projekt sollten die Nachrüstkomponenten des Systems "EuskirchenPlus" ihre Tauglichkeit auch für Pkw-Insassen in Anprallprüfungen (Crashtests) beweisen. Dies gelang zunächst nicht. Daher wurden die Nachrüstkomponenten zu neuen Konstruktionen ("ESP-Motorrad" und "EDSP-Motorrad") weiterentwickelt, und es gelang, die "ESP-Motorrad" erfolgreich zu prüfen. Die Eignung der "EDSP-Motorrad" wurde aus den vorliegenden Forschungsergebnissen und den Erfahrungen der BASt abgeleitet. Das Kompatibilitätsproblem konnte zwar nicht umfassend gelöst, jedoch soweit beseitigt werden, dass keine relevanten Einsatzbeschränkungen mehr aufrecht erhalten werden müssen. Die "ESP-Motorrad" und die "EDSP-Motorrad" sind auf nahezu allen für Motorradunfälle relevanten Strecken grundsätzlich geeignet, die klassischen Stahlschutzplanken ESP beziehungsweise EDSP zu ersetzen.
This work aims at bringing evidence for mass incompatibility in frontal impact for cars built according to the UNECE R94 regulation. French national injury accidents database census for years 2005 to 2008 were used for the analysis. The heterogeneity of frontal self-protection among cars of different masses is investigated, as well as the partner protection parameter offered by these cars. The last part of the analysis deals with the estimation of the benefit, in terms of fatal and severe injuries avoided, if crashworthiness was harmonized for the whole fleet of vehicle. This calculation is done for France and is extended to all Europe.
Small overlap frontal crashes are defined by a damage pattern with most of the vehicle deformation concentrated outboard of the main longitudinal structures. These crashes are prominent among frontal crashes resulting in serious and fatal injuries, even among vehicles that perform well in regulatory and consumer information crash tests. One of the critical aspects of understanding these crashes is knowing the crash speeds that cause the types of damage associated with serious injuries. Laboratory crash tests were conducted using 12 vehicles in three small overlap test conditions: pole, vehicle-to-vehicle collinear, and vehicle-to-vehicle oblique (15-degree striking angle). Field reconstruction techniques were used to estimate the delta V for each vehicle, and these results were compared with actual delta V values based on vehicle accelerometer data. Estimated delta Vs were 50% lower than actual values. Velocity change estimates for small overlap frontal crashes in databases such as NASS-CDS significantly underestimate actual values.
In road traffic accidents, a car-seat and its occupant can be subjected to various crash pulses in the case of a rear impact. This study investigates the influence of crash pulse shape on seat-occupant response and evaluates the corresponding risk of whiplash injury. For this purpose, a rigorously validated seat-occupant system model is used to study different carseat designs and crash pulses. Two different car-seat concepts are also presented which can effectively mitigate whiplash injury for a wide range of crash severity. It is shown that for crash pulses of similar severity, the level of whiplash-risk depends strongly on the combined effects of seat design and crash pulse shape.
Powered Two Wheelers (PTWs) accidents constitute one of the road safety problems in Europe. PTWs fatalities represent 22% at EU level in 2006, having increased during last years, representing an opposite trend compared to other road users" figures. In order to reduce these figures it is necessary to investigate the accident causation mechanisms from different points of view (e.g.: human factor, vehicle characteristics, influence of the environment, type of accident). SAFERIDER project ("Advanced telematics for enhancing the SAFEty and comfort of motorcycle RIDERs", under the European Commission "7th Framework Program") has investigated PTW accident mechanisms through literature review and statistical analyses of National and In-depth accident databases; detecting and describing all the possible PTW's accident configurations where the implementation of ADAS (Advanced Driver Assistance Systems) and IVIS (In-Vehicle Information Systems) could contribute to avoid an accident or mitigate its severity. DIANA, the Spanish in-depth database developed by CIDAUT, has been analyzed for that purpose. DIANA comprises of accident investigation teams, in close cooperation with police forces, medical services, forensic surgeons, garages and scrap yards. An important innovation is the fact that before injured people arrive to hospitals, photographs and explanations about the possible accident injury mechanisms are sent to the respective hospitals (via 3G GPRS technology). By this, additional information to medical staff can be provided in order to predict in advance possible internal injuries and select the best medical treatment. This methodology is presented in this paper. On the other hand, the main results (corresponding to road, rider and PTW characteristics; pre and post-accident manoeuvres; road layout; rider behaviour; impact points; accident causations;...) from the analyses of the PTW accidents used for SAFERIDER are shown. Only accident types relevant to ADAS and IVIS devices have been considered.
The aim of this study is to investigate the differences in car occupant injury severity recorded in AIS 2005 compared to AIS 1990 and to outline the likely effects on future data analysis findings. Occupant injury data in the UK Cooperative Crash Injury Study Database (CCIS) were coded for the period February 2006 to November 2007 using both AIS 1990 and AIS 2005. Data for 1,994 occupants with over 6000 coded injuries were reviewed at the AIS and MAIS level of severities and body regions to determine changes between the two coding methodologies. Overall there was an apparent general trend for fewer injuries to be coded at the AIS 4+ severity and more injuries to be coded at the AIS 2 severity. When these injury trends were reviewed in more detail it was found that the body regions which contributed the most to these changes in severity were the head, thorax and extremities. This is one of the first studies to examine the implications for large databases when changing to an updated method for coding injuries.
Each year the traffic accident research teams in Dresden and Hanover provide an in-depth investigation of approximately two thousand accidents, aggregated in the GIDAS database. To accomplish a comprehensive review of each traffic accident recorded, a sensible and thorough encoding of suffered injuries is indispensable. The Abbreviated Injury Scale by AAAM offers a valuable and handy solution to achieve this goal. However, there were a few difficulties in the use of the AIS that came up in the past, which let to necessary improvements for the utilization of the AIS 2005 for GIDAS.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Abstract: Für Kinder in Deutschland existiert im Pkw weiterhin ein höheres Risiko, im Straßenverkehr bei einem Unfall schwer verletzt oder getötet zu werden, als es für ungeschützte Verkehrsteilnehmer wie Fahrradfahrer oder Fußgänger besteht. Dies erscheint auf den ersten Blick nicht nachvollziehbar, da der Pkw und die vorgeschriebenen Kindersitze den Kindern eine hohe Sicherheit bieten müssten. Der vorliegende Projektbericht gibt Aufschluss über den aktuellen Stand der Sicherheit von Kindern im Pkw in Deutschland und zeigt Optimierungspotenzial auf. Die Schutzwirkung der Kindersitze hängt von mehreren Faktoren ab. Dabei stehen technische Aspekte, die hier detailliert untersucht wurden, im Vordergrund. Doch vor allem in den letzten Jahren zeigte sich immer wieder in Feldstudien, aber auch in der Unfallanalyse, dass Kinderschutzsysteme (KSS) oftmals nicht nach den Vorgaben installiert wurden. Wenn der Kindersitz und/oder das Kind nicht entsprechend der Bedienungsanleitung gesichert werden, kann sich das Schutzpotenzial der KSS reduzieren und gegen Null gehen. Im schlimmsten Fall stellt eine fehlerhafte Benutzung von KSS eine Gefahr sowohl für das Kind als auch für andere Pkw-Insassen dar. Die Unfallanalyse ergab keine Aussage darüber, ob verschiedene KSS-Modelle zu unterschiedlichen Verletzungsmustern führen, da die Unfallkonstellationen pro KSS-Modell zu verschieden waren. Des Weiteren wurde analysiert, inwieweit heutige Testverfahren mit diesen Konstellationen übereinstimmen. Das Ziel, mit wenigen Verfahren möglichst alle relevanten Unfälle abzubilden, wurde zum Teil ereicht. Zu viele Testverfahren mit unterschiedlichen Bewertungssystemen stellen heutzutage die Endverbraucher vor das Problem, dass nicht klar ist, welches KSS wirklich das beste ist. In der Realität hängt die Schutzwirkung zudem noch wesentlich von der KSS-Pkw-Kombination ab, die nur annähernd durch Versuche überprüft werden kann, da sich eine zu hohe Anzahl von Kombinationsmöglichkeiten ergibt. Anhand von mehr als 100 Versuchen wurde das Schutzpotenzial von verschiedenen aktuellen Kindersitzmodellen untersucht. Dabei wurden immer vermeintlich gute und schlechte KSS gegenübergestellt und unter gleichen Randbedingungen getestet. Ziel dieses Vorgehens war es, anhand der Messergebnisse Maßnahmen zu erkennen, die dem Schutz der Kinder dienlich sind. Zusammenfassend kann gesagt werden, dass prinzipiell für Kinder ein gutes Schutzniveau durch KSS besteht, was aber von KSS zu KSS verschieden sein kann. Die teureren KSS wiesen keine mechanische Zerstörung auf und überstanden alle Tests ohne ernsthafte Beschädigungen. Lediglich das oftmals als Dämpfungsmaterial eingesetzte Polystyrol nahm Energie auf und verformte sich wie vorgesehen plastisch. Bei den "Billig-Kindersitzen" ergab sich leider ein komplett anderes Bild. Sobald die Anforderungen über die der Gesetzgebung hinausgehen, ist immer weniger Schutz für die Kinder vorhanden. Besonders im Seitenaufprall offenbarten sich erhebliche Lücken in der Sicherheit. Dies reichte von mechanischem Versagen mancher Plastikteile bis hin zu konstruktiven Unzulänglichkeiten. Vor allem die Gurtführung muss deutlicher gekennzeichnet und mechanisch verstärkt werden. Trotz des hohen Schutzpotenzials einiger Kindersitze ist das Ende der Entwicklung noch nicht abzusehen. In allen Kindersitzklassen ist es prinzipiell möglich, die Belastungswerte weiter zu reduzieren. Dazu werden am Ende des Berichtes verschiedene Möglichkeiten aufgezeigt. Zum einen ist dies eine optimierte Babyschale, die durch eine Trägheitsbewegung gezielt Energie abbaut und das Baby in eine günstigere Position bringt, in der die Belastungen des Körpers reduziert sind. Zum anderen wird gezeigt, dass durch die feste Anbindung des KSS an den Pkw und die Reduzierung der Rotation um die Y-Achse die Belastungen für Kinder reduziert werden können. Größtes Entwicklungspotenzial bietet dabei das ISOFIX-System. Es ist bekannt, dass ISOFIX die Fehlbedienung des Kindersitzes und die Belastungen der Kinder deutlich reduzieren kann. Trotzdem ist die bisherige Marktdurchdringung von ISOFIX eher gering. Obwohl insgesamt ein positives Fazit gezogen werden kann, darf nicht aufgehört werden, die Kindersicherheit weiter zu verbessern. Denn nicht alle Kindersitze schützen heute gleich gut. Einige genügen lediglich den Gesetzesansprüchen und finden in vielen Fällen durch einen sehr geringen Verkaufspreis Zugang in die Pkw. Durch verschärfte Testbedingungen sollten diese Kindersitze abgeschafft und der Weg für neue und bessere Kinderschutzsysteme frei gemacht werden.
Es ist zu beobachten, dass trotz einer Abnahme der Zahl der Verletzungen und der Verletzungsschwere der Insassen bei Pkw-Unfällen Halswirbelsäulen (HWS)-Distorsionen, speziell im unteren Geschwindigkeitsbereich häufiger auftreten. Neben anderen Faktoren werden auch veränderte Beschleunigungs- und Verzögerungsimpulse, die im Crashfall auf die Insassen wirken, als möglicherweise ursächlich für die Entstehung von HWS-Distorsionen angesehen. In der vorliegenden Arbeit wird untersucht, welchen Einfluss konstruktive Veränderungen, die durch Versicherungseinstufungstests bedingt werden, auf die Beschleunigungs- und Verzögerungsimpulse im Fahrzeuginnenraum haben. Versuche zum Fußgängerschutz wurden einvernehmlich nicht durchgeführt, da die Fahrzeuge noch nicht konsequent nach Fußgängerschutzkriterien konzipiert werden. Die Untersuchungsmethode lässt sich gliedern in: - Analyse von internationalen Versicherungssystemen und Analyse der aus den Versicherungseinstufungstests resultierenden Veränderungen von Fahrzeugstrukturen; - Durchführung und Analyse von eigenen Aufprallversuchen mit Fahrzeugteilstrukturen und vergleichende Analyse von Vollfahrzeugversuchen der Versicherungswirtschaft; Zusammenführen der getätigten Schritte. Bei der Ersteinstufung eines Pkw in die Vollversicherung dient der Versicherungseinstufungstest des RCAR/AZT (Prüfgeschwindigkeit 15 km/h) zur Bestimmung der Schadenshöhe und damit zur Einstufung in eine Typklasse. In vielen weiteren Staaten dienen dieser oder ähnliche Tests zur Bewertung der Reparaturfreundlichkeit von Pkw. Um bei einem Versicherungseinstufungstest den Schaden möglichst gering zu halten, haben nahezu alle Neufahrzeuge Querträgersysteme mit kostenarm wechselbaren Absorptionselementen, die die Crashenergie gezielt auf kurzem Weg aufnehmen. Durch die neu EG-Richtlinie 2003/102/EG zum Fußgängerschutz müssen zukünftig hinter der Stoßfängeraußenhaut und vor dem massiven Querträger weiche Schäume untergebracht werden. Der Bauraum für Querträger und Energieabsorptionselemente wird dadurch weiter eingeschränkt. Diese Anforderungen veranlassen die Hersteller dazu, die Energieabsorptionselemente steifer zu gestalten, um einen effektiven Energieabbau bei kurzen Stopplängen zu gewährleisten. Durch diese Maßnahmen wird zwar der Insassenschutz bei Frontalaufprallen im Hochgeschwindigkeitsbereich verbessert, es werden aber zugleich höhere Innenraumverzögerungen (schnellerer Anstieg, höhere mittlere Verzögerung) bei Crashs im gesamten Geschwindigkeitsbereich erzeugt. Eine durchgeführte Korrelation zwischen konstruktiven Veränderungen am Fahrzeug und empirisch bestimmten Verzögerungsverläufen zeigte, dass eine günstigere Einstufung in der Fahrzeugvollversicherung nicht zwangsläufig höhere Verzögerungsimpulse für den Innenraum bedingen muss. Bei der Analyse von 172 Crashversuchen des Allianz Zentrums für Technik mit Neufahrzeugen aus den Jahren 1992 bis 2003 zeichnen sich aber statistisch bedeutsame ßnderungen in den Verzögerungsverläufen über die Prüfjahre ab: - Anstieg der Verzögerung wird steiler; - Mittelwert der Verzögerung wird grösser; - Zeitdauer bis zum Auftreten der maximalen Verzögerung wird kürzer; - dynamische Gesamtdeformation wird kleiner. Die steife Auslegung der für den Versicherungseinstufungstest relevanten Crashteile verbessert den Insassenschutz bei Hochgeschwindigkeitscrashs. Wenn es sich aber durch weitere Untersuchungen bestätigt, dass höhere Verzögerungs- beziehungsweise Beschleunigungsimpulse die Auftretenswahrscheinlichkeit von HWS-Verletzungen im Niedriggeschwindigkeitsbereich vergrößern, so sollten gezielt Maßnahmen zur Verringerung dieser Verletzungsrisiken ergriffen werden. Dazu gehören die weitere Optimierung der Sitzstrukturen einschließlich der Kopfstützen und die Entwicklung adaptiver Crashstrukturen, die dem Crashfall angepasste Kraft-Weg-Kennlinien ermöglichen.
Validation of human pedestrian models using laboratory data as well as accident reconstruction
(2007)
Human pedestrian models have been developed and improved continually. This paper shows the latest stage in development and validation of the multibody pedestrian model released with MADYMO. The biofidelity of the multibody pedestrian model has been verified using a range of full pedestrian-vehicle impact tests with a large range in body sizes (16 male, 2 female, standing height 160-192cm, weight 53.5-90kg). The simulation results were objectively correlated to experimental data. Overall, the model predicted the measured response well. In particular the head impact locations were accurately predicted, indicated by global correlation scores over 90%. The correlation score for the bumper forces and accelerations of various body parts was lower (47-64%), which was largely attributed to the limited information available on the vehicle contact characteristics (stiffness, damping, deformation). Also, the effects of the large range in published leg fracture tolerances on the predicted risk to leg fracture by the pedestrian model were evaluated and compared with experimental results. The validated mid-size male model was scaled to a range of body sizes, including children and a female. Typical applications for the pedestrian models are trend studies to evaluate vehicle front ends and accident reconstructions. Results obtained in several studies show that the pedestrian models match pedestrian throw distances and impact locations observed in real accidents. Larger sets of well documented cases can be used to further validate the models especially for specific populations as for instance children. In addition, these cases will be needed to evaluate the injury predictive capability of human models. Ongoing developments include a so-called facet pedestrian model with a more accurate geometry description and a more humanlike spine and neck and a full FE model allowing more detailed injury analysis.
NASS: the glass is half full
(2007)
The National Accident Sampling System (NASS) was born in the late 1970s. It was based on a substantial amount of experience and analysis of what was needed in the United States to understand the safety challenges of our highways. This work also showed how to collect high quality and useful crash data efficiently. Unfortunately, when Ronald Reagan - a President who believed in limited government - was elected, any hope of full funding for NASS was lost. The concept of 75 teams investigating about 18,000 serious crashes in detail annually was never realized. The system got up to 50 teams, then was cut to 36, and finally to 24 teams investigating fewer than a quarter of the originally anticipated number of crashes per year. Despite this, the NASS investigations provide a rich source of data, collected according to a sophisticated statistical sampling system to facilitate detailed national estimates of road casualties on our nation- highways and their causes. In addition, changes have been made in recent years to increase the number of more serious crashes of recent model vehicles to make the results more relevant to improving vehicle safety. A recent, detailed examination of hundreds of rollovers has provided considerable insight into rollover casualties and into what can be done to reduce them. Some of these results will be presented that show the value of the NASS system. Our experience with NASS and the Fatal Accident Reporting System (FARS) suggests a number of improvements that could be made in the United States" crash data systems. It also provides justification for a doubling or tripling of our national expenditures on crash data collection.
The European Enhanced Vehicle-safety Committee (EEVC) Working Group 13 for Side Impact Protection has been developing an Interior Headform Test Procedure to complement the full-scale Side Impact Test Procedure for Europe and for the proposed IHRA test procedures. In real world accidents interior head contacts with severe head injuries still occur, which are not always observed in standard side impact tests with dummies. Thus a means is needed to encourage further progress in head protection. At the 2003 ESV-Conference EEVC Working Group 13 reported the results on Interior Headform Testing. Further research has been performed since and the test procedure has been improved. This paper gives an overview of its latest status. The paper presents new aspects which are included in the latest test procedure and the research work leading to these enhancements. One topic of improvement is the definition of the Free Motion Headform (FMH) impactor alignment procedure to provide guidelines to minimize excessive headform chin contact and to minimize potential variability. Research activities have also been carried out on the definition of reasonable approach head angles to avoid unrealistic test conditions. Further considerations have been given to the evaluation of head airbags, their potential benefits and a means of ensuring protection for occupants regardless of seating position and sitting height. The paper presents the research activities that have been made since the last ESV Conference in 2003 and the final proposal of the EEVC Headform Test Procedure.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
Electronic Stability Program (ESP) aims to prevent the lateral instability of a vehicle. Linked to the braking and powertrain systems, it prevents the car from running wide on a corner or the rear from sliding out. It also helps the driver control his trajectory, without replacing him, in the case of loss of control where the driver is performing an emergency manoeuvrer (confused and exaggerated steering wheel actions). A new ESP function optimizes ESP action in curves with hard under steering (situations in which the front wheels lose grip and the vehicle slides towards the outside of the curve). A complementary feature prevents the wheels from spinning when pulling away and accelerating. The name given to the ESP system varies according to the vehicle manufacturer, but other terms include: active stability control (ASC), automotive stability management system (ASMS), dynamic stability control (DSC), vehicle dynamic control (VDC), vehicle stability control (VSC) or electronic stability Control (ESC). This paper proposes an evaluation of the effectiveness of ESP in terms of reduction of injur accidents in France. The method consists of 3 steps: - The identification, in the French National injury accident census (Gendarmerie Nationale only), of accident-involved cars for which the determination of whether or not the car was fitted with ESP is possible. A sample of 1 356 cars involved in injury accidents occurred in 2000, 2001, 2002 and 2003 was then selected. But we had to restrict the analysis to only 588 Renault Lagunas. - The identification of accident situations for which we can determine whether or not ESP is pertinent (for example ESP is pertinent for loss of control accidents whilst it is not for cars pulling out of a junction). - The calculation, via a logistic regression, of the relative risk of being involved in an ESPpertinent accident for ESP equipped cars versus unequipped cars, divided by the relative risk of being involved in a non ESP-pertinent accident for ESP equipped cars versus unequipped cars. This relative risk is assumed to be the best estimator of ESP effectiveness. The arguments for such a method, effectiveness indicator and implicit hypothesis are presented and discussed in the paper. Based on a few assumptions, ESP is proved to be highly effective. Currently, the relative risk of being involved in an ESP pertinent accident for ESP-equipped cars is lower (-44%, although not statistically significant)rnthan for other cars.rn
Neben den Airbags für den Frontalaufprall haben sich auch Seitenairbags in allen Fahrzeugklassen etabliert. Diese sind für viele Fahrzeugmodelle auch auf den äußeren Fondsitzplätzen, dem typischen Sitzplatz für Kinder im Auto, erhältlich. Seitenairbags können das Verletzungsrisiko für erwachsene Pkw-Insassen in einem Seitenaufprall reduzieren. Doch der Einfluss dieser Airbagsysteme auf Kinder, die mit Kinderrückhaltesystemen im Fahrzeug gesichert sind, war bislang weitgehend unbekannt. In dieser Studie wurden die Wechselwirkungen zwischen Seitenairbags und gesicherten Kindern experimentell untersucht. Zunächst wurden die Unfalldatenbanken der Medizinischen Hochschule Hannover und des GDV abgerufen. Dort waren jedoch keine Fälle registriert, bei denen ein Seitenairbag auf einem Sitzplatz mit installiertem Kinderrückhaltesystem ausgelöst wurde. Da nicht auf Unfalldaten zurückgegriffen werden konnte, wurde zunächst versucht, die Häufigkeit von Seitenairbagsystemen im deutschen Straßenverkehr so exakt wie möglich zu quantifizieren. Dabei sollten auch die konzeptionellen Unterschiede der Airbagsysteme berücksichtigt werden. Darüber hinaus wurden die möglichen Sitzpositionen von Kinderdummys in gebräuchlichen Kinderrückhaltesystemen untersucht. Ziel war es, Aufschluß über möglicherweise gefährliche Sitzpositionen zu erlangen. Basierend auf diesen Untersuchungen wurden fünf Konfigurationen für die experimentellen Untersuchungen festgelegt. Das Hauptaugenmerk lag dabei auf sogenannten Risiko-OoP-Situationen, bei denen sich das richtig gesicherte Kind im Rahmen seiner Bewegungsmöglichkeiten innerhalb des Sitzes dem Airbagmodul nähert. Aufgrund der in Deutschland herrschenden Pflicht, Kinder entsprechend ihrem Alter im Fahrzeug zu sichern, blieben die in den entsprechenden Richtlinien (ISO, 1999; LUND, 2000) definierten OoP-Konfigurationen unberücksichtigt. Auch gefährliche Misuse-Situationen, in denen das Kind aufgrund falsch installierter Rückhaltesysteme in den direkten Entfaltungsbereich des Seitenairbags gelangen kann, wurden nicht betrachtet. Da diese Sitzpositionen generell das Verletzungsrisiko für Kinder im einem Unfall erhöhen können, wurde sich in dieser Studie auf den Normalfall, das korrekt gesicherte Kind, konzentriert. Letztendlich sind fünf Fahrzeuge für die experimentellen Untersuchungen ausgewählt worden. Diese wurden in Stand- und full-scale-Versuchen mit verschiedenen Dummys der Hybrid III-Serie und Kinderrückhaltesystemen getestet. Ausgehend von den Resultaten der Airbagstandversuche wurden in den full-scale-Versuchen die Systeme mit dem vermeintlich geringsten Schutzpotential sowie der am meisten gefährdete Kinderdummy mit verschiedenen Seitenairbags kombiniert. Von jedem Fahrzeugmodell wurden zwei Fahrzeuge des gleichen Baujahres sowie mit gleicher Ausstattung beschafft. Jeweils ein Fahrzeug wurde mit Seitenairbag und das andere ohne Seitenairbag getestet. So konnten positive oder negative Effekte des Airbags im Seitenaufprall überprüft werden. Zur Beurteilung der Messwerte wurden die Belastungsgrenzen und Schutzkriterien der "Side Airbag Out-of-Position Injury Technical Working Group" (LUND, 2000) verwendet. Die in den Standversuchen ermittelten Dummybelastungen blieben zum Teil deutlich unter den Limits. In den full-scale-Versuchen konnte der Seitenairbag die Kopf- und Brustkorbbelastungen teilweise reduzieren. Jedoch führt der Seitenairbag zu einer starken Drehung des Dummykopfes um die z-Achse. Der Grenzwert von 17 Nm wurde jeweils überschritten. Die durchgeführten Analysen und Versuche lassen den Schluss zu, daß Seitenairbags gesicherte kindliche Insassen nicht außerordentlich gefährden. In bestimmten Situationen bieten sie dem Kind zusätzlichen Schutz. Dennoch ist ein Airbag kein harmloses System. Treffen ungünstige Randbedingungen zusammen, so kann der Seitenairbag das Verletzungsrisiko auch für gesicherte Kinder erhöhen. Als besonders sensibel erwies sich der Hals der Dummys. Hier kann ein ungünstiges Airbagdesign zu erhöhten Belastungen führen.
Durch die Einführung des Airbags als zusätzliches Rückhaltesystem zum Sicherheitsgurt hat sich die Sicherheit für die Fahrzeuginsassen weiter erhöht. Die Airbagtechnologie wird nunmehr seit mehr als zehn Jahren serienmäßig verbaut. Nach wie vor berichten die Autofahrer aber immer wieder auch über Probleme mit dieser Technologie. Ziel dieser Arbeit ist es, geeignetes Datenmaterial aus dem realen Unfallgeschehen zu sammeln und daraus aktuelle Aussagen zur Schutzwirkung der Airbag-Technologie zu gewinnen. Darüber hinaus sollen aus dem Material auch Erkenntnisse über die Art, Häufigkeit und Ursachen der Probleme abgeleitet und damit Vorschläge für weitere Verbesserungen entwickelt werden. Die Datenbeschaffung erfolgt über eine Umfrage in den Zeitschriften der europäischen Automobilclubs. Zusammen mit dem Airbagmaterial der Versicherer stehen insgesamt 692 Fälle für die Auswertung zur Verfügung. Es ergibt sich, dass bei schweren Frontalkollisionen der Anteil an schweren bis tödlichen Verletzungen sowohl für den Fahrer als auch für den Beifahrer um gut 20 % niedriger ist als bei vergleichbaren Unfällen ohne Airbag. Auch die Seiten- und Kopfseiten-Airbags zeigen in Einzelfällen eine gute Schutzwirkung. Wegen der geringen Fallzahlen ist aber noch keine allgemeingültige Aussage möglich. Das Datenmaterial beinhaltet 78 Problemfälle im Zusammenhang mit der Airbag-Auslösung. Es handelt sich zum einen um ungerechtfertigte Auslösungen ohne Unfall oder bei geringer Unfallschwere, und zum anderen um Nichtauslösungen bei hoher Unfallschwere. Besonders auffällig sind hier die Nichtauslösungen beim Unterfahrunfall. Im Rahmen dieser Arbeit wurde auch ein Unterfahr-Test entwickelt, der in Zukunft im Rahmen der Airbag-Optimierung mit eingesetzt werden sollte. Im Datenmaterial befinden sich auch 92 Problemfälle mit Airbag-Aggressivität. Der häufigste Fall ist hier der Gehörschaden und zwar durch die Auslösung der Front-Airbags. Über gezielte Maßnahmen zur Schallpegelreduzierung bei der Airbag-Entfaltung, durch mehrstufige Airbagauslössung in Abhängigkeit von der Unfallschwere sowie durch Sitzbelegungserkennung könnten hier Verbesserungen erreicht werden. Zur Minimierung des Out-of-Position-Risikos sollte der FMVSS 208-Test mit 5 % Dummy in der vordersten Sitzposition bei die Airbag-Abstimmung eingesetzt werden. Die Airbag-Technologie hat die Insassensicherheit nachhaltig erhöht. Es ist aber noch ein großes Entwicklungspotential für weitere Verbesserungen vorhanden.
The frontal crash is still an important contributor to deaths and serious injured resulting from road accidents in Europe. As the Hybrid-III dummy used in crash tests is over two decades old, the European Enhanced Vehicle-safety Committee is studying the potential for a new test device. Key is the availability of a well-defined set of requirements that identifies the minimum level of biofidelity required for an advanced frontal dummy. In this paper, a complete set of frontal impact biofidelity requirements, consisting of references , description of test conditions and corridors, is presented.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
In der Bundesrepublik Deutschland beträgt der Anteil der Fußgänger an den Verkehrstoten derzeit circa 13 Prozent. Um die Verletzungsschwere bei Fahrzeug-Fußgänger-Kollisionen zu reduzieren, wurde 1996 ein vom "European Enhanced Vehicle-safety Committee" (EEVC) ausgearbeitetes Testverfahren zum Fußgängerschutz als europäischer Gesetzentwurf (III/502/96 EN) veröffentlicht. Das Testverfahren schreibt den Einsatz verschiedener Körperteilmodelle für die Bereiche Kopf, Oberschenkel und Bein zur Prüfung der Fahrzeugvorderwagen vor. Diese Stoßkörper müssen bei der Prüfung verschiedene Beanspruchungsgrenzwerte einhalten. Das vorliegende Projekt befasst sich mit der fußgängerfreundlichen Gestaltung von Fahrzeugfronten unter Berücksichtigung des von der EEVC WG10 ausgearbeiteten Testverfahrens sowie dessen Überarbeitung durch die EEVC WG17. Es werden zunächst eine Mittelklasselimousine und eine Großraumlimousine nach dem Prüfverfahren der EEVC getestet. Auf Basis der Versuchsergebnisse wird die Mittelklasselimousine mit dem Ziel modifiziert, die Prüfergebnisse zu verbessern. Anhand der Analyse der daraufhin realisierten Fahrzeugoptimierung wird anschließend das EEVC Testverfahren einer kritischen Betrachtung unterzogen. Dafür werden Optimierungsmaßnahmen an Fahrzeugen, die zu Verbesserungen der Ergebnisse des EEVC Testverfahrens führen, auf ihre Wirkung bei realen Fußgängerunfällen bewertet. Weiterhin werden Anmerkungen zu der praktischen Durchführung des Testverfahrens gemacht, wobei auch Fahrzeuge mit besonderen Konstruktionsmaßnahmen, wie zum Beispiel aktive Schutzsysteme, berücksichtigt werden.
An approach to the standardization of accident and injury registration systems (STAIRS) in Europe
(1998)
STAIRS is a European Commission funded study whose aim is to produce a set of guidelines for a harmonised, crash injury database. The need to evaluate the effectiveness of the forthcoming European Union front and side impact directives has emphasised the need for real world crash injury data-sets that can be representative of the crash population throughout Europe. STAIRS will provide a methodology to achieve this. The ultimate aim of STAIRS is to produce a set of data collection tools which will aid decision making on vehicle crashworthiness as well as providing a means to evaluate the effectiveness of safety regulations. This paper will disseminate the up-to-date findings of the group as they try to harmonise their methods. The stage has been reached where studies into the diverse methods of the UK, French and German systems of crash injury investigation have been undertaken. An assessment has already been made of the relationships between the three current systems in order to define the areas of agreement and divergence. The conclusions reached stated that there were many areas that are already closely related and that the differences were only at the detailed level. With the emphasis on secondary safety and injury causation, core data sets were decided upon, taking into account: vehicle description, collision configuration, structural response of vehicles, restraint and airbag performance, child restraint performance, Euro NCAP, pedestrian and vehicle occupant kinematics, injury description and causation. Each variable was studied objectively, the important elements isolated and developed into a form that all partners were agreeable on. A glossary of terms is being developed as the project progresses which includes ISO standards and other definitions from the associated CAREPLUS project, which addresses the comparability of national data sets. A major consideration of the group was the data collection method to be employed. The strengths and weaknesses of each study were investigated to obtain a clear idea of which aspects offered the best way forward. The quality of this information and transference into a common format, as well as the necessary error checking systems to be employed have just been completed and are described. In tandem with this area of study the problem of the statistical relationship of each sample to the national population is also being investigated. The study proposes a mechanism to use a sample of crash injury data to represent the national and international crash injury problem
Bewertung der Fahrzeug-Fußraumintrusionen beim Offset Frontaltest gegen das Verformungselement
(1998)
In den Tests nach dem neuen Frontaltestverfahren (Entwürfe ECE R.94 sowie Richtlinie 96/79/EG und Ergänzung zu RL 70/156/EWG) entstehen hohe Verformungen der Fußräume der Versuchsfahrzeuge. Die Bewertung der Gefährdung der Insassen durch Intrusion, vorwiegend der Spritzwand begleitet von heftigen Bewegungen der Pedale, soll durch am Dummy zu messende Schutzkriterien erfolgen. Es ist vorgesehen, an den Dummies die Verschiebung des Schienbeins gegen das Knie, die Längskraft im Unterschenkel und den sogenannten Tibia Index zu messen. Um dieses zu ermöglichen, mussten an den vorhandenen Dummy-Unterschenkeln konstruktive Änderungen vorgenommen werden. Über die Herleitung der Schutzkriterien, Fragen bei der Anwendung dieser Kriterien sowie die technischen Einzelheiten und die Zertifizierung der neuen Dummy-Unterschenkel, welche die erforderlichen Messungen erlauben, wird berichtet.
In der Europäischen Gemeinschaft werden derzeit jährlich ca. 50.000 Menschen bei Verkehrsunfällen getötet, ca. 10.000 davon als Fußgänger. Von den 10.600 (1992) in der Bundesrepublik Deutschland bei Straßenverkehrsunfällen Getöteten waren 1.800 Fußgänger (etwa 17 Prozent). Problemgruppen bei Fußgängerunfällen bilden die Kinder wegen ihrer hohen Unfallhäufigkeit und alte Personen wegen ihrer hohen Unfallschwere. Kopfverletzungen sind die häufigste Todesursache bei Fußgängerunfällen. Eine Verringerung der Unfallschwere kann - außer durch Verminderung von Fahr- beziehungsweise Aufprallgeschwindigkeiten der Fahrzeuge - nur durch konstruktive Eingriffe an der vorderen Fahrzeugaußenkontur oder dem Unterbau von Pkw erfolgen. Dazu ist es notwendig, einheitliche Prüfverfahren für die Beurteilung der "Fahrzeugaggressivität" gegenüber Fußgängern bereitzustellen. Die Ableitung eines Prüfvorschlages zur Simulation des Kopfaufpralls auf Fronthauben von Pkw beim Fußgängerunfall, unterteilt in Kopfaufpralltests für Erwachsene und Kinder, ist Gegenstand dieser Arbeit. Es werden, ausgehend von einer Analyse der Unfallstatistik, der Entstehungsmechanismus von Kopfverletzungen erklärt, die für ein Prüfverfahren notwendigen Eingangsparameter (Masse, Geschwindigkeit, Aufprallstellen am Fahrzeug etc.) abgeleitet und die Ergebnisse der gewählten Prüfkörpertestmethode mit Ergebnissen von Leichenversuchen verglichen. Eine Kosten-/Nutzen-Betrachtung am Schluss der Arbeit zeigt, dass sich bei nur geringen Kosten ein volkswirtschaftlicher Nutzen durch eine allgemeine Anwendung des Prüfverfahrens mit ca. 270 Millionen DM allein in der Bundesrepublik Deutschland pro Jahr erzielen ließe.
Um die Verletztenschwere von ungeschützten Verkehrsteilnehmern bei der Kollision mit Personenkraftwagen zu reduzieren, sollte die Fahrzeugfront bestimmten Anforderungen entsprechen. Dazu wurde von der EEVC-WG 10 ein Testverfahren zur Prüfung der Pkw-Frontfläche vorgeschlagen. In dieser Untersuchung wurde der Nutzen an vermeidbaren Personenschäden geschätzt, der erzielt werden könnte, wenn alle Pkw diese Anforderungen erfüllten. Als Nutzen wurde das Reduktionspotential bei Getöteten, der mögliche Übergang von Schwerverletzten zu Leichtverletzten und von Leichtverletzten zu Unverletzten bewertet. Verletzungsminderungen innerhalb der Gesamtheit der Schwerverletzten konnten nicht bewertet werden. Auch die hohe Dunkelziffer der Verletzten ging nicht in die Rechnung ein. Daraus ergibt sich, dass der errechnete Nutzen eine Mindestgröße darstellt. Diese Größe wird stark beeinflusst von einer gegebenen Verteilung der Pkw-Kollisionsgeschwindigkeiten, denn ein Nutzenpotential des EEVC-WG-10-Testverfahrens kann nur für Kollisionsgeschwindigkeiten bis 40 km/h angenommen werden. Um mit einer verlässlichen Datenbasis zu arbeiten, wurde diese Untersuchung zunächst für die Bundesrepublik Deutschland (Gebietsstand vor dem 3. Oktober 1990) und das Jahr 1990 durchgeführt. Dafür errechnete sich ein Nutzenpotential pro neuzugelassenem Pkw in Höhe von 46 bis 63 DM (22 bis 31 ECU) nach deutschen Unfallkostensätzen oder 28 bis 36 ECU nach europäischen Durchschnittskostensätzen. Wirtschaftlich ist die Maßnahme, solange die Kosten pro neu zugelassenem Pkw (zum Preisstand 1990) diesen Betrag nicht übersteigen. Von diesem Ergebnis ausgehend, wurde dessen zeitliche und regionale Übertragbarkeit erörtert. Es ist wahrscheinlich, dass das Ergebnis für ganz Deutschland gilt, da die Maßnahme nicht vor dem Jahr 2000 eingeführt wird und die Vollausrüstung aller Pkw mit dem geforderten Fußgängerschutz erst 10 Jahre später erreicht ist. Aus Prognosen bis zum Jahre 2010 für die Entwicklung der Bevölkerungszahl (gleichbleibender Fußgängeranteil vorausgesetzt) und der Zahl der Pkw-Neuzulassungen lässt sich keine Änderung des Nutzenpotentials herleiten. Weil für andere EG-Länder die Verteilung der Kollisionsgeschwindigkeiten bei Fußgängerunfällen unbekannt ist, können die Wirksamkeitsannahmen dieser Untersuchung nicht auf andere Länder übertragen werden.
Der Nutzen des Schutzhelmes für motorisierte Zweiradfahrer ist unumstritten. Die Grenzwerte für eine zulässige Kopfbeschleunigung bei der Prüfung des Dämpfungsverhaltens gemäß ECE-R 22 sind jedoch weiterhin in der Diskussion. In der vorliegenden Untersuchung wird deshalb die Kopfbelastung eines Dummys beim Pkw-Crash-Versuch mit den Belastungen des behelmten Prüfkopfes bei Fallversuchen gemäß ECE-R 22 verglichen. Bei den durchgeführten Fallversuchen besteht ein enger Zusammenhang zwischen HIC und maximaler Beschleunigung, der durch eine analytische Funktion beschrieben werden kann. Es kann gezeigt werden, dass die bei ECE-R 22 zulässige Kopfbeschleunigung von 300 g einem HIC von etwa 3400 entspricht. Zur Bewertung von Schutzhelmen mit verbesserten Stoßabsorptionseigenschaften erscheint es sinnvoll, wie anhand von Modellrechnungen gezeigt wird, den HIC als Schutzkriterium einzuführen. Bei einer Anprallgeschwindigkeit von 7 m/s kann ein HIC von 1500 als realistische Forderung angesehen werden, sofern bei der ECE-Regelung der sogenannte Zweitschlag entfällt. Bei den Pkw-Versuchen ist kein Zusammenhang zwischen HIC und maximaler Beschleunigung vorhanden. Hier ist der HIC als Verletzungskriterium etabliert, und das ist für den komplexen Verlauf des Signals der Kopfbeschleunigung sinnvoll. Eine Bewertung nach anderen Kopfschutzkriterien würde die Rangfolge der einzelnen Versuche ändern. Bei Helmversuchen auf den Stirnanprallpunkt B werden starke Rotationen des rückprallenden Systems Prüfkopf/Helm beobachtet. In Verbindung damit treten hohe Rotationsbeschleunigungen auf. Diese liegen, wie bei einem Teil der Helmversuche gemessen, zwischen 2,4 und 4,8 krad/s2.
Seit Anfang der 70er Jahre kann im Bereich der passiven Sicherheit eine stetige Verbesserung durch die Abnahme der im Verkehr verletzten und getöteten Personen beobachtet werden. Weitere fahrzeugtechnische Optimierungen zur Verbesserung von Selbst- und Partnerschutz, unterstützt und forciert durch flankierende legislative Maßnahmen, sind durchzuführen, wobei parallel die Effizienz bereits getroffener Maßnahmen zu prüfen ist. In der Pilotstudie wird der Versuch gemacht, ausgehend von bekannten Erkenntnissen der Unfallanalyse, das Gesamtunfallgeschehen Pkw zu realitätsbezogenen, in ihren Wirkungsmechanismen gleichartigen Unfallkonstellationen zusammenzufassen. Die Reduzierung auf wenige Kollisionstypen schafft die Möglichkeit zur Erarbeitung von Testbedingungen. Die im Test nachzufahrenden Unfallkonstellationen und die statisch/dynamische Untersuchung einzelner Fahrzeugkomponenten dokumentieren sich in physikalischen Messwerten und fahrzeugbezogenen Größen. Ein Bewertungssystem addiert die Messwerte auf und versieht sie mit relevanzproportionalen Wichtungsfaktoren zu einem Sicherheitsgrad. Praktische Bedeutung hat das Projekt zum Beispiel für die quantitative Ermittlung des Sicherheitsfortschrittes innerhalb eines Zeitraumes von 10 bis 15 Jahren, der Untersuchung von Sicherheitskomponenten und der Effizienzüberprüfung legislativer Sicherheitsverordnungen etc.
Erkenntnisse über den Nutzen zusätzlicher hochgesetzter Bremsleuchten sind lückenhaft und zum Teil widersprüchlich. Im Rahmen einer Untersuchung über den Einfluss zusätzlicher Bremsleuchten auf das Unfallgeschehen wurden u.a. folgende Fragen behandelt: 1. Entwicklung der Unfälle durch Auffahren auf Fahrzeuge, die mit zusätzlichen Bremsleuchten ausgerüstet sind, 2. Entwicklung der Auffahrunfälle insgesamt, 3. Verletzungen von Fahrzeuginsassen durch Leuchten, 4. Auswirkungen auf die übrigen Verkehrsteilnehmer (Abstand, Blendung, Fehlreaktion). Anhand konkreter Daten über das Unfallgeschehen in Bayern und Niedersachsen kommt der Beitrag insgesamt zu dem Urteil, dass die derzeitige Regelung weder durch eine Einbauvorschrift noch durch ein Einbauverbot hochgesetzter Bremsleuchten ersetzt werden müsste.
Schutz von Fahrzeuginsassen
(1983)
Ausgehend von unfallstatistischen Daten und Ausführungen über Unfallablauf und Unfallfolgen werden Schutzmaßnahmen diskutiert, die das Verletzungsrisiko für Fahrzeuginsassen möglichst niedrig halten. Die Wirksamkeit von Schutzmaßnahmen wird beeinflusst von der Unfallkonstellation, Eigenschaften der Pperson und vom Fahrzeug (Deformationscharakteristik, Auslegung des rückhaltesystems). Die Gesamtwirksamkeit hängt wiederum ab von der Wirksamkeit des Rückhaltesystems, der Benutzungshäufigkeit und der Benutzungsqualität. Die Arbeit endet mit volkswirtschaftlichen Überlegungen und kommt zu dem Schluss, dass auch in Zukunft als wichtigste Maßnahme zum Schutz von Fahrzeuginsassen die Erhöhung der Anlegequote für Sicherheitsgurte anzusetzen ist.
Sicherheitsgurte sind als wirksamer Schutz für Pkw-Insassen bei Verkehrsunfällen weltweit anerkannt; trotzdem werden sie in der Bundesrepublik Deutschland von den Autofahrern noch nicht im wünschenswerten Maße benutzt, obwohl Sicherheitsgurte in ihren Fahrzeugen eingebaut sind. Von dieser Situation ausgehend behandelt die vorliegende Studie sowohl die wirtschaftlichen, rechtlichen und technischen Aspekte, einschließlich alternativer Rückhaltesysteme, als auch die Frage nach der Wirksamkeit des Sicherheitsgurtes. Die Auswertung der internationalen Literatur und die Erörterung der anstehenden Probleme mit Experten führten zu folgenden Feststellungen: - Der Dreipunktgurt kann sowohl hinsichtlich seines Bedienungs- und Tragekomforts als auch im Hinblick auf die beabsichtigte Schutzwirkung im Detail verbessert werden. - Derzeit gibt es keine serienreifen Alternativen zum Gurtsystem. - Das Risiko von gurtbedingten Verletzungsverschlimmerungen ist gering, so dass ihm keine ausschlaggebende Bedeutung beigemessen werden kann. - Ausländische Erfahrungen zeigen, dass durch die Einführung eines Bußgeldes die Kraftfahrer in ihrer überwiegenden Mehrheit die Anlegepflicht befolgen. - Würden in der Bundesrepublik Deutschland alle Frontinsassen von Pkw den Gurt stets anlegen, so könnte der derzeitige Sicherheitsgewinn praktisch verdoppelt werden.
Die Beurteilung der technischen und unfallrelevanten Eigenschaften der beiden Scheibenarten zeigt, dass die VSG-Scheibe gegenüber der ESG-Scheibe hinsichtlich der Verletzungs- und Unfallgefahr zwar überwiegend Vorteile aufweist; diese Vorteile sind jedoch vor allem vor dem Hintergrund steigender Gurtanlegequoten nicht als so entscheidend anzusehen, dass daraus die Begründung für ein Verbot der ESG-Scheibe abzuleiten wäre. Diese Feststellung wird insbesondere auch gestützt durch eine Nutzen-Kosten-Betrachtung, die zeigt, dass aus gesamtwirtschaftlicher Sicht bei einem generellen Ersatz der ESG-Scheibe durch die teurere VSG-Scheibe bei günstigen Annahmen der Nutzen unter den Kosten liegen würde.