620 Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (45)
- Buch (Monographie) (18)
- Wissenschaftlicher Artikel (4)
- Arbeitspapier (1)
Schlagworte
- Injury (68) (entfernen)
Institut
In der Bundesrepublik Deutschland beträgt der Anteil der Fußgänger an den Verkehrstoten derzeit circa 13 Prozent. Um die Verletzungsschwere bei Fahrzeug-Fußgänger-Kollisionen zu reduzieren, wurde 1996 ein vom "European Enhanced Vehicle-safety Committee" (EEVC) ausgearbeitetes Testverfahren zum Fußgängerschutz als europäischer Gesetzentwurf (III/502/96 EN) veröffentlicht. Das Testverfahren schreibt den Einsatz verschiedener Körperteilmodelle für die Bereiche Kopf, Oberschenkel und Bein zur Prüfung der Fahrzeugvorderwagen vor. Diese Stoßkörper müssen bei der Prüfung verschiedene Beanspruchungsgrenzwerte einhalten. Das vorliegende Projekt befasst sich mit der fußgängerfreundlichen Gestaltung von Fahrzeugfronten unter Berücksichtigung des von der EEVC WG10 ausgearbeiteten Testverfahrens sowie dessen Überarbeitung durch die EEVC WG17. Es werden zunächst eine Mittelklasselimousine und eine Großraumlimousine nach dem Prüfverfahren der EEVC getestet. Auf Basis der Versuchsergebnisse wird die Mittelklasselimousine mit dem Ziel modifiziert, die Prüfergebnisse zu verbessern. Anhand der Analyse der daraufhin realisierten Fahrzeugoptimierung wird anschließend das EEVC Testverfahren einer kritischen Betrachtung unterzogen. Dafür werden Optimierungsmaßnahmen an Fahrzeugen, die zu Verbesserungen der Ergebnisse des EEVC Testverfahrens führen, auf ihre Wirkung bei realen Fußgängerunfällen bewertet. Weiterhin werden Anmerkungen zu der praktischen Durchführung des Testverfahrens gemacht, wobei auch Fahrzeuge mit besonderen Konstruktionsmaßnahmen, wie zum Beispiel aktive Schutzsysteme, berücksichtigt werden.
Thorax injury is one of main causes of serious injury in frontal collisions, especially for elderly car occupants. The anthropometric test device (ATD) THOR‐M provides chest deflection measurements at multiple locations, to assess the risk of thorax injury. For this purpose e, risk functions are needed that relate the potential criteria based on multipoint chest deflection measurement to in jury risk. Different thorax injury criteria and risk functions for THOR have been proposed [2‐3]. The criteria and functions are based on the traditional approach to developing injury risk functions using matched ATD and PMHS tests by relating the injury (number of fractures) to injury criteria. Regarding these studies, some limitations have been identified, in particular concerning the loading conditions of the data used (mainly 3‐point‐belt loading, high loading severity, out‐of‐date ATD versions. To extend the data set and overcome these limitations, a new approach for improved thorax injury criteria was applied within the EC‐funded project SENIORS. The new approach is based on matched frontal impact sled computer simulations with a model representing the latest THOR‐M ATD version, and matching simulations with a human body model (HBM) representing an elderly car occupant.
Bewertung der Fahrzeug-Fußraumintrusionen beim Offset Frontaltest gegen das Verformungselement
(1998)
In den Tests nach dem neuen Frontaltestverfahren (Entwürfe ECE R.94 sowie Richtlinie 96/79/EG und Ergänzung zu RL 70/156/EWG) entstehen hohe Verformungen der Fußräume der Versuchsfahrzeuge. Die Bewertung der Gefährdung der Insassen durch Intrusion, vorwiegend der Spritzwand begleitet von heftigen Bewegungen der Pedale, soll durch am Dummy zu messende Schutzkriterien erfolgen. Es ist vorgesehen, an den Dummies die Verschiebung des Schienbeins gegen das Knie, die Längskraft im Unterschenkel und den sogenannten Tibia Index zu messen. Um dieses zu ermöglichen, mussten an den vorhandenen Dummy-Unterschenkeln konstruktive Änderungen vorgenommen werden. Über die Herleitung der Schutzkriterien, Fragen bei der Anwendung dieser Kriterien sowie die technischen Einzelheiten und die Zertifizierung der neuen Dummy-Unterschenkel, welche die erforderlichen Messungen erlauben, wird berichtet.
Autonomous Emergency Braking (AEB) systems for pedestrians have been predicted to offer substantial benefit. On this basis, consumer rating programmes, e.g. Euro NCAP, are developing rating schemes to encourage fitment of these systems. One of the questions that needs to be answered to do this fully, is to determine how the assessment of the speed reduction offered by the AEB is integrated with the current assessment of the passive safety for mitigation of pedestrian injury. Ideally, this should be done on a benefit related basis. The objective of this research was to develop a benefit based methodology for assessment of integrated pedestrian protection systems with pre-crash braking and passive safety components. A methodology has been developed which calculates the cost of pedestrian injury expected, assuming all pedestrians in the target population (i.e. pedestrians impacted by the front of a passenger car) are impacted by the car being assessed, taking into account the impact speed reduction offered by the car’s AEB (if fitted) and the passive safety protection offered by the car’s frontal structure. For rating purposes, this cost can be normalised by comparing it to the cost calculated for selected cars. The methodology uses the speed reductions measured in AEB tests to determine the speed at which each casualty in the target population will be impacted. The injury to each casualty is then calculated using the results from standard Euro NCAP pedestrian impactor tests and injury risk curves. This injury is converted into cost using ‘Harm’ type costs for the body regions tested. These costs are weighted and summed. Weighting factors were determined using accident data from Germany and GB and the results of a benefit analysis performed by the EU FP7 AsPeCSS project. This resulted in German and GB versions of the methodology. The methodology was used to assess cars with good, average and poor Euro NCAP pedestrian ratings, with and without a current AEB system fitted. It was found that the decrease in casualty injury cost achieved by fitting an AEB system was approximately equivalent to that achieved by increasing the passive safety rating from poor to average. Also, it was found that the assessment was influenced strongly by the level of head protection offered in the scuttle and windscreen area because this is where head impact occurs for a large proportion of casualties. The major limitation within the methodology is the assumption used implicitly during weighting. This is that the cost of casualty injuries to body areas, such as the thorax, not assessed by the headform and legform impactors, and other casualty injuries such as those caused by ground impact, are related linearly to the cost of casualty injuries assessed by the impactors. A methodology for assessment of integrated pedestrian protection systems was developed. This methodology is of interest to consumer rating programmes which wish to include assessment of these systems. It also raises the interesting issue if the head impact test area should be weighted to reflect better real-world benefit.
During the past five years, a Euro NCAP technical working group on pedestrian safety has been working on improving test and assessment procedures for enhanced passive pedestrian safety. After harmonizing the tools and procedures as much as possible with legislation, the work was mainly focused on the development of grid procedures for the pedestrian body regions head, upper leg with pelvis and lower leg with knee. Furthermore, the test parameters for the head and the upper leg were revised, a new lower legform impactor was introduced and the injury thresholds were adjusted or, where necessary, the injury criteria were changed. Finally, the assessment limits and colour scheme were refined, widening the range and adding two more colours in order to provide a more detailed description of the pedestrian safety performance. By abstaining from an assessment based on a worst point selection philosophy, the improved test point determination procedures that were introduced during the years 2013 and 2014 give a more homogeneous, high resolution picture of the pedestrian safety performance of the vehicle frontends. By using a uniform grid for each test zone approximately 200 test points, evenly distributed within each area, can now be assessed per vehicle. The introduction of the flexible pedestrian legform impactor in 2014 enables a more realistic injury prediction of the knee and the tibia using a biofidelic test tool. With the new upper legform test that has been launched in 2015 the assessment in that area is now focusing on the injured body region instead of the injury causing vehicle part and thus is aligned with the approach in the remaining body regions head and lower leg. At the same time, a monitoring test with the headform impactor against the bonnet leading edge is closing the possible gap between the test areas to identify injury causing vehicle parts that moved out of focus due to the introduction of the new upper legform test. The paper describes the new test and assessment procedures with their underlying philosophy and gives an outlook in terms of open issues, specifying the needs for further improvement in the future. In parallel to the work of the pedestrian subgroup, a Euro NCAP working group on heavy vehicles introduced a set of protocol changes in 2011 that were related to the assessment of M1 vehicles derived from commercial vehicles, with a gross vehicle weight between 2.5 and 3.5 tons and 8 or 9 seats. The paper also investigates the applicability of the new pedestrian test and assessment procedures to heavy vehicles.
Frontal impact is still the most relevant impact direction in terms of injury causation amongst car occupants. Especially for car-to-car frontal impacts the mass ratio between the involved vehicles has a significant impact on the injury risk (the heavier the opponent car the higher the injury risk). In order to address this issue frontal Mobile Deformable Barrier test procedures have been developed world-wide (for example the MPDB procedure that was fully described during the FIMCAR Project). The objective of this study was to investigate how vehicles of different weight classes perform in a mobile barrier test procedure compared to a fixed barrier test procedure (the full width rigid and offset deformable barrier test). Beyond that, the influence of vehicle mass and vehicle deformation on injuries was evaluated based on real world accident data. Five vehicle types were selected and tested in a fixed offset test procedure (ODB), a full width rigid barrier test procedure (FWRB) and a mobile offset test procedure (MPDB). For the accident analyses data from the German In-Depth Accident Study (GIDAS) was evaluated with a focus on MAIS 2+ injured belted front row car (UN-R 94 compliant cars) occupants in frontal impact accidents. Test data indicates higher dummy loadings, in particular for the head acceleration and chest acceleration, in the MPDB test for the vehicles with a mass lighter than the trolley (1,500 kg) compared to the FWRB test. The trend of increased vehicle stiffness (especially illustrated by tests with the MPDB and small cars) shows the need of a further improvement of passive restraint systems to reduce the occupant loading and with it the injury risk. The analyzed GIDAS data confirm the higher injury risk for occupants in cars with an accident weight of less than 1,500 kg compared to those with a crash weight above 1,500 kg in car-to-car and car-to-object or car-to-HGV, respectively. Furthermore the injury risk increases with decreasing mass ratio (i.e., the opponent car is heavier) in car-to-car accidents. Independent from the higher injury risk, the risk for passenger compartment intrusion in frontal impact appears not to be independent on the crash weight of the car.
Schutz von Fahrzeuginsassen
(1983)
Ausgehend von unfallstatistischen Daten und Ausführungen über Unfallablauf und Unfallfolgen werden Schutzmaßnahmen diskutiert, die das Verletzungsrisiko für Fahrzeuginsassen möglichst niedrig halten. Die Wirksamkeit von Schutzmaßnahmen wird beeinflusst von der Unfallkonstellation, Eigenschaften der Pperson und vom Fahrzeug (Deformationscharakteristik, Auslegung des rückhaltesystems). Die Gesamtwirksamkeit hängt wiederum ab von der Wirksamkeit des Rückhaltesystems, der Benutzungshäufigkeit und der Benutzungsqualität. Die Arbeit endet mit volkswirtschaftlichen Überlegungen und kommt zu dem Schluss, dass auch in Zukunft als wichtigste Maßnahme zum Schutz von Fahrzeuginsassen die Erhöhung der Anlegequote für Sicherheitsgurte anzusetzen ist.
Test and assessment procedures for passive pedestrian protection of passenger cars are in place for many years within world-wide regulations as well as consumer test programmes. Nevertheless, recent accident investigations show a stagnation of pedestrian fatality numbers on European roads alongside increasing injury severities for older road users. The EU-funded SENIORS (Safety ENhancing Innovations for Older Road userS) project developed and evaluated a thorax injury prediction tool (TIPT) for later incorporation within test and assessment procedures. Accident data indicates an increasing portion of AIS2 and AIS3+ thoracic injuries of older pedestrians and cyclists which are currently not assessed in any test procedure for vulnerable road users. Therefore, SENIORS focused on the development of a test tool predicting the risk of rib fractures of vulnerable road users (VRU). While injury risk functions were reanalyzed, human body model (HBM) simulations against categorized generic vehicle frontends served as input for the definition of test setups and corresponding impact parameters. TIPT component tests against a generic frontend and an actual vehicle were used for the evaluation of the technical feasibility. The TIPT component tests shows the general feasibility of a test procedure for the assessment of thoracic injuries, with good repeatability and reproducibility of kinematics and results. Impact parameters such as the inclination angles of the thorax, angles of the velocity vector and impact speeds well replicate the parameters gained from the HBM simulations. The proposed markup and assessment scheme offers the possibility of a homogeneous evaluation of the protection potential of vehicle frontends while maintaining justifiable testing efforts. During evaluation testing, the proposed requirements were entirely met. The developed prototype of TIPT and launching system offer impact angles and speeds as suggested by HBM simulations. However, since thorax impacts during pedestrian accidents do not occur perpendicularly to the vehicle surface in most cases, the TIPT built-in linear potentiometers do not acquire the true resultant intrusions on the ribcage and thus, TIPT rib deflections do not reflect the actual human injury risk. However; for the impact forward to the bonnet leading edge, the TIPT seems applicable without further modifications. The test and assessment procedures using the TIPT offer for the first time the possibility of replicating the kinematics of a pedestrian thorax with a component test. The developed assessment scheme gives a first indication on how the risk for thoracic injuries could be implemented within the Euro NCAP Box 3 assessment. Future development of the TIPT may focus on implementing a rib cage that can deflect in all axes in a humanlike way.
To assess occupant safety in a crash test, criteria associating the measurements made with a crash test dummy to injury risk are necessary. To enable better protection of elderly car occupants the objective of this study was to develop improved thoracic injury criteria for the THOR average male dummy. The development of these criteria is usually based on matched dummy and Post Mortem Human Surrogate (PMHS) tests by relating the obtained PMHS injuries to dummy measurements. This approach is limited, since only a few tests in relevant loading conditions are available and any new test series requires high efforts to be performed due to their complexity and costs. To overcome these limitations and to extend the dataset for the development of THOR dummy chest injury risk functions a simulation-based approach was applied within the EC funded project SENIORS (Safety Enhanced Innovations For older Road Users - www.seniors-project.eu). Within this study frontal impact sled simulations with an FE model representing a THOR average male dummy and matched simulations with a human body model (HBM) representing an elderly car occupant were carried out. The HBM used for this study was the THUMS TUC with modified rib cage, which was developed in SENIORS. The modifications included material and geometry changes aiming to represent an elderly car occupant. The rib fracture risk was predicted with a deterministic approach whereby a rib was considered broken when the strain exceeded an age-dependent threshold. Furthermore, a probabilistic method was applied to predict the probability of sustaining a certain number of fractured ribs by comparing local strain values to the distribution of cortical rib ultimate strain. By relating the output from the HBM simulations to a multi-point dummy injury criterion, injury risk curves were calculated by statistical methods. The wide range of loading conditions resulted in the desired range of injuries and THOR ATD output. The number of fractured ribs predicted by the HBM based on the deterministic prediction method was between 0 and 15. Furthermore, the probabilistic risk for the number of rib fractures equal or greater than two, three or four was calculated for each load case. The THOR rib deflection criterion Rmax was between 18 and 56 mm, while the PC Score was in the range of 2.5 to 7.2. Based on these outputs new risk curves for the predicted deterministic (AIS2+/3+) and probabilistic injury risk were calculated. The new curves show reasonable shapes and significance that provide trust in their application. The new risk curves are compared to risk curves obtained by traditional methods. The results were found similar to previous injury risk functions based on physical tests, which gives a high level of confidence in the chosen approach. The simulation-based approach of matched ATD model vs. HBM simulation was successfully applied. Rmax curves show a slightly better quality than the injury criterion PC Score.
Anhand von zwei verschiedenen Versuchskonfigurationen wurde das Schutzpotential von Kopfschutzsystemen (Fahrradhelm und airbagbasiertes System) untersucht. Hierbei wurden die resultierende Kopfbeschleunigung als Messwert sowie das Kopfverletzungskriterium HIC bei Versuchen ohne und mit Kopfschutzsystem vergleichend gegenübergestellt.