Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (63)
- Buch (Monographie) (25)
- Bericht (1)
- Arbeitspapier (1)
Schlagworte
- Analysis (math) (90) (entfernen)
Institut
- Sonstige (90) (entfernen)
Since 2005, the motorcycle crash fatalities in the US exceeded 10% of the overall annual traffic fatalities. Consequently, it has become critical to gain in-depth understanding of the factors and characteristics contributing to motorcycle crashes. Unfortunately, there currently exists no database gathering the necessary information for an in-depth analysis of the US motorcycle crashes. So this study utilizes the NASS/CDS database (National Automotive Sampling System, Crashworthiness Data System) in order to gain insights into the patterns and factors leading to a NASS/CDS motorcycle crash, from 1997 to 2007. NASS/CDS samples about 5,000 passenger car tow-away crashes per year. Each case includes photographs and detailed data on crash and pre-crash characteristics, vehicle types, trajectories, types of impact, and other pertinent roadway and crash scene information, allowing an in-depth investigation of the crash mechanisms. However, the NASS/CDS sampling process specifically focuses on passenger car crashes, so the cases extracted only correspond to crashes in which a passenger vehicle was towed, and a motorcycle was somehow involved. Thus, a by-hand in-depth review of about 200 cases allowed retrieving 106 relevant crashes for this study, tending to represent the severe passenger vehicle(s) versus motorcycle(s) crashes on US roads. The findings lead to the conclusion that these crashes mostly result from the low conspicuity of the motorcycle, and from the inability of the car drivers to fully appreciate and anticipate the behavior of a motorcycle. Indeed, it has been shown that, first, the car drivers involved in these cases did not attempt any avoidance maneuver, second, they were largely of ages under 25, and finally, the majority of the crashes were in an intersection scenario. In addition, the two major scenarios unveiled were the car attempting a left turn from the opposite direction and the car attempting a left turn from the right. The paper mentions several solutions to enhance the motorcycle- conspicuity and to allow the car drivers to better anticipate its behavior, which seem to be key factors in the intersection-related crashes (and more generally in the passenger vehicle(s) versus motorcycle(s) crashes).
Small overlap frontal crashes are defined by a damage pattern with most of the vehicle deformation concentrated outboard of the main longitudinal structures. These crashes are prominent among frontal crashes resulting in serious and fatal injuries, even among vehicles that perform well in regulatory and consumer information crash tests. One of the critical aspects of understanding these crashes is knowing the crash speeds that cause the types of damage associated with serious injuries. Laboratory crash tests were conducted using 12 vehicles in three small overlap test conditions: pole, vehicle-to-vehicle collinear, and vehicle-to-vehicle oblique (15-degree striking angle). Field reconstruction techniques were used to estimate the delta V for each vehicle, and these results were compared with actual delta V values based on vehicle accelerometer data. Estimated delta Vs were 50% lower than actual values. Velocity change estimates for small overlap frontal crashes in databases such as NASS-CDS significantly underestimate actual values.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
The NHTSA-sponsored Crash Injury Research and Engineering Network (CIREN) has collected and analyzed crash, vehicle damage, and detailed injury data from over 4000 case occupants who were patients admitted to Level-I trauma centers following involvement in motor vehicle crashes. Since 2005, CIREN has used a methodology known as "BioTab" to analyze and document the causes of injuries resulting from passenger vehicle crashes. BioTab was developed to provide a complete evidenced-based method to describe and document injury causation from in-depth crash investigations with confidence levels assigned to the causes of injury based on the available evidence. This paper describes how the BioTab method is being used in CIREN to leverage the data collected from in-depth crash investigations, and particularly the detailed injury data available in CIREN, to develop evidence-based assessments of injury causation. CIREN case examples are provided to demonstrate the ability of the BioTab method to improve real-world crash/injury data assessment.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
From literature well-known analyzes on risks, hazards and causes of accidents of older drivers are amended by the present study in which a comparison of the specific features of accident causes of older car drivers (older than 60 years) and of younger car drivers (under 25 years) is conducted. Mainly the question is pursued if specific errors, mistakes and lapses are predominant in the two different age groups. The analysis system ACAS (Accident Causation Analysis System) used hereby consists of a sequential system of accident causation factors from the human, the technical and the infrastructural field, whereupon for this study the influence of the human features on the accident development in two different age groups is of interest. ACAS is both an accident model and an analysis and classification system, which describes the human participation factors of an accident and their causes in the temporal sequence (from the perceptibility to concrete action errors) taking into consideration the logical sequence of individual basic functions. In five steps (categories) of a logical and temporal sequence the hierarchical system makes human functions and processes as determinants of accident causes identifiable. The methodology specifically focuses on the use in so-called "In-Depth" and "On-Scene" investigation studies. With the help of the system for each accident participant one or more of five hypotheses of human cause factors are formed and then specified by appropriate verification criteria. These hypotheses in turn are further specified by indicators in such manner that the coding of the causation factors by a code system meets the needs of database processing and are accessible to a quantitative data analysis. The first results of the descriptive comparison of the two age groups concern mainly differences in the functional levels "information admission/perception" (where the elderly drivers have more difficulties than the young ones) and "information processing/evaluation" (where the younger drivers show more problems). Concerning the cognitive function of "planning" the group of younger drivers seems to be more often involved in an accident because of excessive speed.
In general the passive safety capability is much greater in newer versus older cars due to the stiff compartment preventing intrusion in severe collisions. However, the stiffer structure which increases the deceleration can lead to a change in injury patterns. In order to analyse possible injury mechanisms for thoracic and lumbar spine injuries, data from the German Inâ€Depth Accident Study (GIDAS) were used in this study. A twoâ€step approach of statistical and caseâ€byâ€case analysis was applied for this investigation. In total 4,289 collisions were selected involving 8,844 vehicles, 5,765 injured persons and 9,468 coded injuries. Thoracic and lumbar spine injuries such as burst, compression or dislocation fractures as well as soft tissue injuries were found to occur in frontal impacts even without intrusion to the passenger compartment. If a MAIS 2+ injury occurred, in 15% of the cases a thoracic and/or lumbar spine injury is included. Considering AIS 2+ thoracic and lumbar spine, most injuries were fractures and occurred in the lumbar spine area. From the case by case analyses it can be concluded that lumbar spine fractures occur in accidents without the engagement of longitudinals, lateral loading to the occupant and/or very severe accidents with MAIS being much higher than the spine AIS.
Analysis of the accident scenario of powered two-wheelers on the basis of real-world accidents
(2013)
For the first time since 20 years the German national statistics of traffic accidents revealed an increasing number of fatalities and seriously injured persons in 2011. This negative development was especially caused by increasing numbers in all groups of vulnerable road users (VRU). Furthermore, the comparison of fatality reduction rates between several categories of road users shows that persons on motorcycles show the worst performance over years. Although every second fatality in German traffic accidents is still a car occupant, users of PTW make up more than 20% in the meantime. Assuming further improvements in the field of occupant protection this trend will continue. For that reason, a study on the basis of real-world accidents was conducted to describe the accident scenario involving motorcycles and to identify the reasons of the above-described fact. Approximately 1.800 motorcycle accidents out of GIDAS database were used for the analyses. The first part of the study deals with the question how representative the GIDAS database is for the German motorcycle accident scenario. Afterwards, detailed descriptive statistics on motorcycle accidents were presented considering numerous parameters about the accident scene, environmental influences, vehicle information, individual characteristics, interview data, injury severity and injury causation. One important point is the identification of the most frequent critical situations that are typical for motorcycle accidents. Furthermore, a special focus was on accident causation. Finally, conspicuous facts out of the analysis are emphasized. All in all, the study gives a comprehensive overview about the German motorcycle accident scenario. One the one hand, the use of weighted GIDAS data allows representative and robust statements on the basis of large case numbers; on the other hand highly detailed conclusions can be drawn. The results of the study help to understand the particularities of motorcycle accidents and provide approaches for further improvements in the field of PTW safety.
With an ever rising human life expectancy the share of elderly people in society is constantly rising. This leads to the fact that at the same rate the share of people with age related diseases such as dementia and poor eyesight taking part in traffic will rise and therefore traffic accidents caused by this group of people due to the disease will play an ever greater role. This Situation will be among the future challenges of road safety work. At present this study displays specific characteristics of accidents caused by elderly car drivers (aged 65 or higher) based on the analysis of the German In-Depth Accident Study GIDAS. Herein almost 1000 elderly car drivers were identified as accident participants in the years 2008 to 2011. The focus of this study lies on identifying special types of accidents which are caused by elderly drivers and on characterizing these types with the information gathered on scene and by interviewing the participants. The main evidence analyzed is the knowledge about the accident locality, the trajectories of the participants as well as the reasons for the occurrence of the accidents. Furthermore personal information such as the personal condition before the accident and driving purposes is used to identify patterns of contributing circumstances for accidents caused by elderly traffic participants.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
Nowadays human-created systems are increasing in complexity due to the interaction of humans and technology. Especially road traffic systems are composed of multitudinous resources (e.g. personnel, vehicles, organizations, etc.), which make it even harder to anticipate the positive and negative effects on safety. One key in achieving a significant reduction of fatalities is seen in driver assistant systems counterbalancing the lack of drivers' capabilities. But the actual outcome of implementing these sophisticated technologies especially on influencing driver's capabilities are yet unknown. Latest research exemplifies an increase of reaction times of drivers in case of dysfunctional driver assistant systems. This research paper applies STAMP/STPA (STAMP = systems-theoretic accident model and processes; STPA = systems-theoretic process analysis) to the German automobile traffic system focusing on the effects of driver assistant systems on drivers. By doing so, the potential hazards caused by technology can be identified.
Die Untersuchung zum Forschungsprojekt FE 82.0499/2011 "Ausdehnung der Kostentragungspflicht des -§ 25a StVG auf den fließenden Verkehr" befasst sich mit der Thematik einer möglichen Ausdehnung der bislang ausschließlich für den ruhenden Verkehrs geltenden Kostentragungspflicht des -§ 25a StVG auf Verkehrsverstöße im fließenden Verkehr. Dieses Forschungsprojekt hatte die Aufgabenstellung zu erfüllen, aus der Arbeitspraxis der Bußgeldbehörden in den Bundesländern eine für die Ansprüche wissenschaftlicher Auswertungen qualitativ und quantitativ ausreichende Datenmenge zur Bearbeitung digital erfasster Geschwindigkeits-, Rotlicht- und Abstandsverstöße zu erheben. Dieser Gesamtdatenbestand sollte gesammelt, thematisch geordnet und hinsichtlich der einschlägigen Tatbestände sowie der Verfahrenseinstellungen aufbereitet werden. Hauptergebnis der Studie ist: - Bei einer Gesamtanzahl von 10,7 % eingestellter Bußgeldverfahren wird eine Anzahl von 2,5 % Bußgeldverfahren eingestellt, weil bei einem mittels digitaler Messtechnik beweissicher festgestellten Verkehrsverstoß und zweifelsfrei dokumentiertem Kfz-Kennzeichen der Fahrzeugführer trotz mindestens einer Ermittlungsmaßnahme nicht vor Eintritt der Verfolgungsverjährung ermittelt werden konnte.
Intelligente Bauwerke - Anforderungen an die Aufbereitung von Messgrößen und ihrer Darstellungsform
(2015)
Ziel des Forschungsvorhabens FE 15.0548/2011/GRB war die Ausarbeitung einer Konzeption zu Anforderungen an die Aufbereitung und Verarbeitung von Messgrößen und ihrer Darstellung. Dies beinhaltete die Evaluierung und Entwicklung verschiedener modellbasierter und statistischer Analyseverfahren, die über den bisherigen Stand der Technik der Bauwerksüberwachung hinausgehen. Der Nutzen liegt in der Herausfilterung relevanter Informationen aus umfangreichem Datenmaterial (Vor-Aggregation) sowie der Erzeugung von belastbaren Zustandsinformationen bzw. Vorergebnissen hierzu durch eine frühzeitige, leistungsfähige Plausibilisierung. Es wurde gezeigt, dass durch den Einsatz von leistungsfähigen, gedächtnisbehafteten, selbstlernenden Algorithmen für die Sensorfusion, Interpolation, Plausibilitätserhöhung und Treffen fachtechnischer Monitoringaussagen Ergebnisse erzielt werden können, die bezüglich der Verarbeitung von Mess- und Erfassungsdaten weit über den aktuellen Stand beim Brückenmonitoring hinausgehen. Anhand mehrerer Szenarien, für die reale Erfassungsdaten zur Verfügung standen, wurde gezeigt, dass diese Verfahren sehr zuverlässig verschiedenste Signalstörungen, wie Messausreisser, erhöhtes Rauschen und Brummeinstreuung erkennen können. Nur durch die frühzeitige und zuverlässige Plausibilisierung von Sensordaten von Brückenbauwerken kann verhindert werden, dass offensichtlich fehlerhafte Messwerte (wie z.B. Messausreisser, störungsbehaftete Messungen) zu falschen Vorhersagen der Systemzuverlässigkeit von Brückenbauwerken durch rechnergestützte Systemmodelle führen.
Zur Ermittlung einer Mehr- oder Minderbeanspruchung des Straßenoberbaus durch Lang-Lkw wurde eine Stichprobe von 1.746 Fahrten im Direktverkehr und 483 Fahrten im kombinierten Verkehr analysiert. Die durchschnittliche Fahrzeuggesamtmasse der Lang-Lkw betrug 32,3 t. Ca. 9 % der Lang-Lkw fuhren überladen. Das Niveau der Überladungen lag jeweils unterhalb 3 t. Die maximale Achslast betrug 11,7 t. Die Achslastverteilung von Lang-Lkw im kombinierten Verkehr weist ein niedrigeres Niveau als für Lang-Lkw im Direktverkehr auf. Im Vergleich zu äquivalenten konventionellen Lkw ergibt sich für Lang-Lkw eine um 5 % niedrigere Anzahl äquivalenter 10-t-Achsen. Der mittlere Achszahlfaktor fA von Lang-Lkw beträgt 7,40. Das Transportvolumen eines Lang-Lkw entspricht rechnerisch dem Transportvolumen von 1,53 äquivalenten konventionellen Lkw. Mit zunehmendem Anteil Lang-Lkw am Gesamtkollektiv Schwerverkehr (bis zu 9 %) ist eine zunehmende, vergleichsweise geringe Reduzierung der B-Zahl nach RStO 12 zu verzeichnen, was in der Regel jedoch nicht zu einem Wechsel in die nächstkleinere Belastungsklasse führen würde. Mittels Dimensionierung nach RDO Asphalt 09 errechnet sich bei Einsatz von Lang-Lkw nach dem Ende einer 30-jährigen Nutzungsdauer der Straßenbefestigung ein geringfügig niedrigerer Ermüdungsstatus, der zu einer marginalen Verlängerung des Nutzungszeitraums führen würde. Der Einsatz von Lang-Lkw würde unter Einhaltung der im Feldversuch definierten fahrzeugtechnischen Vorgaben und zulässigen Grenzwerte für Fahrzeuggesamtgewichte und Achslasten nicht zur Mehrbeanspruchung des Oberbaus von Straßen führen. Die rechnerisch festgestellte Minderbeanspruchung des Oberbaus im Vergleich zu konventionellen Lkw hat nur marginale Bedeutung und würde sich somit in der Praxis kaum spürbar auf die Nutzungsdauer der Straßen auswirken.
The paper gives an overview of the recent (mostly 2012) figures of killed bus/coach occupants (drivers and passengers) in 27 Member States of the European Union as reported by CARE. The Evolution of the figures of bus/coach occupants killed in road accidents urban, rural without motorway and on motorways from 1991 to 2010 in 15 Member States of the EU supplements this information. More detailed are the figures reported for Germany by the Federal Statistics. The paper displays long-term evaluations (1957 to 2012) for killed, seriously and slightly injured occupants in all kinds of buses/coaches. Midterm evaluations (1995 to 2012) of the figures of fatalities and casualties are displayed for different busses according to their identification of road using as coaches, urban buses, school buses, trolley buses and "other buses". To be able to compare the evolutions of the safety of vehicle occupants it is customary to use different risk indicators. Calculations and illustrations for three often used indicators with their development over time are given: fatalities, seriously injured and slightly injured per 100,000 vehicles registered, per 1 billion (109) vehicle-kilometres travelled and per 1 billion (109) person-kilometres. These indicators are shown for occupants of cars, goods vehicles and buses/coaches. For the period from 1957 until 2012 it is obvious, that for all three vehicle categories analysed there was a clear long-term trend towards more occupant safety in terms of casualties per vehicles registered and per vehicle mileage. This was most significant for car occupants but it can be seen for bus/coach occupants and goodsvehicle occupants as well. Figures of killed occupants and of casualties related to person-kilometres are calculated and displayed for the shorter period 1995 to 2012. Here it becomes obvious that the bus/coach is still the safest mode of transport for the occupants of road vehicles. Graphs for the casualty risk indices still show significantly higher risks for car occupants despite the corresponding curve moved sustainable downwards. It is remarkable, that the risks of being killed or injured for the occupants of urban buses is growing whereas the corresponding risk for the occupants of coaches in line traffic tends downwards. The article ends with a short comparison and discussion of the risk indicators which are actually published for the occupants (driver and passengers) of cars and the passengers of buses/coaches, railroads, trams and airplanes. The interpretation of such information depends on the perception and it seems that for a complete view not only one indicator should be used and the evolutions of the indicator values during longer periods (as displayed with examples in the paper) should also be taken into account.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
Ziel des Forschungsvorhabens war es zu untersuchen, ob in verschiedenen Prüfstellen mit dem Walzsektor-Verdichtungsgerät hergestellte Asphalt-Probeplatten gleiche Eigenschaften aufweisen, damit z.B. verträgliche Ergebnisse für Performance-Prüfungen ermittelt werden können. Dazu wurde in 12 Prüfstellen ein Verfahrens-Audit durchgeführt, um eine einheitliche Vorgehensweise bei der Herstellung dieser Platten zu gewährleisten. Anschließend wurden aus verschiedenen Asphaltvarianten WSV-Platten hergestellt und an daraus gewonnenen Probekörpern umfangreiche Performance-Prüfungen durchgeführt. Die ermittelten Ergebnisse zeigen, dass es möglich ist WSV-Platten mit verträglicher Raumdichte in unterschiedlichen WSV-Geräten sowie verschiedenen Prüfstellen herzustellen. Die Ergebnisse der Spurbildungs-, Druck-Schwell- und Zugversuche haben gezeigt, dass die WSV-Platten trotz ähnlicher Raumdichten nicht zwangsläufig verträgliche Ergebnisse im Versuch aufweisen und sich daher in verschiedenen Prüfstellen keine vergleichbaren Ergebnisse für diese Versuche ermitteln lassen. Lediglich bei den Abkühl- und Spaltzug-Schwellversuchen konnten verträgliche Ergebnisse erzielt werden. Für keine der ermittelten Kenngrößen der Performance-Prüfungen ließen sich Zusammenhänge mit der Raumdichte ermitteln. Somit lässt sich die Größe der Ergebnisse bei den Versuchen nicht auf unterschiedliche Größen der Raumdichten der Probekörper zurückführen. Da sich trotz geringer Unterschiede in den Raumdichten nur in ausgewählten Performance-Untersuchungen Unterschiede zeigen, ist davon auszugehen, dass die Streuungen in den Performance-Untersuchungen vornehmlich auf die Sensitivität dieser Versuche zurückzuführen sind. Das Verfahren zur Herstellung von Probekörpern für Performance-Prüfungen aus WSV-Platten scheint aufgrund der Gesamtheit der ermittelten Kenngrößen (Raumdichte, etc.), deren Aussehen, den Erkenntnissen aus dem Verfahrensaudit sowie der Performance-Prüfungen das richtige Verfahren zu sein.
Interdisciplinary accident research and research projects of AARU Audi Accident Research Unit
(2017)
AARU (Audi Accident Research Unit) is an interdisciplinary research project of the University Hospital Regensburg in cooperation with AUDI AG. Specific objective is to comprehend the respective accident scenario and retrieve generally applicable findings as to technical, medical and psychological processes. In order to prevent traffic accidents and to alleviate vehicle accident consequences, postulates of general traffic safety, human-machine interaction, technical design and function of new vehicles and occupant as well as third party protection shall be inferred from these findings. Specifically, each accident with new Audi, Lamborghini and Ducati vehicles involved is analyzed interdisciplinary, discussed in a case meeting and anonymously documented with more than 2,000 parameters. The database is continually used for solving safety relevant issues. Parallel to accident analysis, research projects are performed in the fields medicine, psychology and engineering in order to gain comprehensive insight and identify potential additional areas of activity of accident research.