Sonstige
Filtern
Dokumenttyp
- Konferenzveröffentlichung (64) (entfernen)
Schlagworte
- Analyse (math) (64) (entfernen)
Institut
In most of developed countries, the progress made in passive safety during the last three decades allowed to drastically reduce the number of killed and severely injured especially for occupants of passenger cars. This reduction is mainly observed for frontal impacts for which the AIS3+ injuries has been reduced about 52% for drivers and 38% for front passengers. The stiffening of the cars' structure coupled with the generalization of airbags and the improvement of the seatbelt restraint (load limiter, pretension, etc.) allowed to protect vital body regions such as head, neck and thorax. However, the abdomen did not take advantage with so much success of this progress. The objective of this study is to draw up an inventory on the abdominal injuries of the belted car occupants involved in frontal impact, to present adapted counter-measures and to assess their potential effectiveness. In the first part the stakes corresponding to the abdominal injuries will be defined according to types of impact, seat location, occupants' age and type of injured organs. Then, we shall focus on the abdominal injury risk curves for adults involved in frontal impact and on the comparisons of the average risks according to the seat location. In the second part we will list counter-measures and we shall calculate their effectiveness. The method of case control will be used in order to estimate odds ratio, comparing two samples, given by occupants having or not having the studied safety system. For this study, two type of data sources are used: national road injured accident census and retrospective in-depth accident data collection. Abdominal injuries are mainly observed in frontal impact (52%). Fatal or severe abdominal occupant- injuries are observed at least in 27% of cases, ranking this body region as the most injured just after the thorax (51%). In spite of a twice lower occupation rate in the back seats compared to the front seats, the number of persons sustaining abdominal injuries at the rear place is higher than in the front place. In recent cars, the risk of having a serious or fatal abdominal injury in a frontal impact is 1.6% for the driver, 3.6% for the front passenger and 6.3% for the rear occupants. The most frequently hurt organs are the small intestine (17%), the spleen (16%) and the liver (13%). The most common countermeasures have a good efficiency in the reduction of the abdominal injuries for the adults: the stiffness of the structure of the seats allows decreasing the abdominal injury risk from 54% (driver) to 60% (front occupant), the seatbelt pretensioners decrease also this risk from 90% (driver) to 83% (front passenger).
Still correlated with high mortality rates in traffic accidents traumatic aortic ruptures were frequently detected in unprotected car occupants in the early years. This biomechanical analysis investigates the different kinds of injury mechanisms leading to traumatic aortic injuries in todays traffic accidents and how the way of traffic participation affects the frequency of those injuries over the years. Based on GIDAS reported traffic accidents from 1973 to 2014 are analyzed. Results show that traumatic aortic injuries are mainly observed in high-speed accidents with high body deceleration and direct load force to the chest. Mostly chest compression is responsible for the load direction to the cardiac vessels. The main observed load vector is from caudal-ventral and from ventral solely, but also force impact from left and right side and in roll-over events with chest compression lead to traumatic aortic injuries. Classically, the injury appeares at the junction between the well-fixed aortic arch and the pars decendens following a kind of a scoop mechanism, a few cases with a hyperflexion mechanism are also described. In our analysis the deceleration effect alone never led to an aortic rupture. Comparing the past 40 years aortic injuries shift from unprotected car occupants to today's unprotected vulnerable road users like pedestrians, cyclists and motorcyclists. Still the accident characteristics are linked with chest compression force under high speed impact, no seatbelt and direct body impact.
To elucidate the risk of pedestrians, bicycle and motorbike users, data of two accident research units from 1999 to 2014 were analysed in regard to demographic data, collision details, preclinical and clinical data using SPSS. 14.295 injured vulnerable road users were included. 92 out of 3610 pedestrians ("P", 2.5%), 90 out of 8307 bicyclists ("B", 1.1%) and 115 out of 4094 motorcycle users ("M", 2.8%) were diagnosed with spinal fractures. Thoracic fractures were most frequent ahead of lumbar and cervical fractures. Car collisions were most frequent mechanism (68, 62 and 36%). MAIS was 3.8, 2.8 and 3.2 for P, B and A with ISS 32, 16 and 23. AIS-head was 2.2, 1.3 and 1.5). Vulnerable road users are at significant risk for spine fractures. These are often associated with severe additional injuries, e.g. the head and a very high overall trauma severity (polytrauma).
While cyclists and pedestrians are known to be at significant risk for severe injuries when exposed to road traffic accidents (RTAs) involving trucks, little is known about RTA injury risk for truck drivers. The objective of this study is to analyze the injury severity in truck drivers following RTAs. Between 1999 and 2008 the Hannover Medical School Accident Research Unit prospectively documented 43,000 RTAs involving 582 trucks. Injury severity including the abbreviated injury scale (AIS) and the maximum abbreviated injury scale (MAIS) were analyzed. Technical parameters (e.g. delta-v, direction of impact), the location of accident, and its dependency on the road type were also taken into consideration. The results show that the safety of truck drivers is assured by their vehicles, the consequence being that the risk of becoming injured is likely to be low. However, the legs especially are at high risk for severe injuries during RTAs. This probability increases in the instance of a collision with another truck. Nevertheless, in RTAs involving trucks and regular passenger vehicles, the other party is in higher risk of injury.
Motorcycle crashes in Austria: Analysis of causes and contributing factors based on in-depth data
(2017)
From CEDATU, the in-depth accident database run by the Vehicle Safety Institute at Graz University of Technology, a representative sample of 101 crashes involving at least one motorcycle was selected. The analysis focused on causes for crashes as well as on contributing factors, but also included parameters of road, riders and vehicles. Own riding speed and "unexpectable action by another road user" were the most frequent causes for accidents. Inappropriate safety distance or delayed reaction were frequent, both as causation factors and as contributing factors. Infrastructure issues never cause an accident, but they are very frequent as contributing factors; road geometry and road guidance are by far most frequent among these. This paper also discusses accidents by type and other parameters (e.g. injury severity by body region, collision speed, age and others), and compares accident causes to previous studies as well as the police reported accident statistics.
Millions of kilometers are driven and recorded by car manufacturers and researchers every year to gather information about realistic traffic situations. The focus of these studies is often the recording of critical situations to create test scenarios for the development of new systems before introducing them into the market. This paper shows a novel Analysis and Investigation Method for All Traffic Scenarios (AIMATS) based on real traffic scenes. It also shows how to get detailed information about speeds, trajectories and behavior of all participants without driving thousands of kilometers at the example of conflict situations with animals. Basis of the AIMATS is the identification of the most relevant locations as "Points of Interest" (POI), the recording of the critical situations and their "base lines" at these POI. This paper presents a new method to identify critical scenarios involving both vehicles and animals as well as preliminary results of a study done in Saxony using this new method.
Interdisciplinary accident research and research projects of AARU Audi Accident Research Unit
(2017)
AARU (Audi Accident Research Unit) is an interdisciplinary research project of the University Hospital Regensburg in cooperation with AUDI AG. Specific objective is to comprehend the respective accident scenario and retrieve generally applicable findings as to technical, medical and psychological processes. In order to prevent traffic accidents and to alleviate vehicle accident consequences, postulates of general traffic safety, human-machine interaction, technical design and function of new vehicles and occupant as well as third party protection shall be inferred from these findings. Specifically, each accident with new Audi, Lamborghini and Ducati vehicles involved is analyzed interdisciplinary, discussed in a case meeting and anonymously documented with more than 2,000 parameters. The database is continually used for solving safety relevant issues. Parallel to accident analysis, research projects are performed in the fields medicine, psychology and engineering in order to gain comprehensive insight and identify potential additional areas of activity of accident research.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
In general the passive safety capability is much greater in newer versus older cars due to the stiff compartment preventing intrusion in severe collisions. However, the stiffer structure which increases the deceleration can lead to a change in injury patterns. In order to analyse possible injury mechanisms for thoracic and lumbar spine injuries, data from the German Inâ€Depth Accident Study (GIDAS) were used in this study. A twoâ€step approach of statistical and caseâ€byâ€case analysis was applied for this investigation. In total 4,289 collisions were selected involving 8,844 vehicles, 5,765 injured persons and 9,468 coded injuries. Thoracic and lumbar spine injuries such as burst, compression or dislocation fractures as well as soft tissue injuries were found to occur in frontal impacts even without intrusion to the passenger compartment. If a MAIS 2+ injury occurred, in 15% of the cases a thoracic and/or lumbar spine injury is included. Considering AIS 2+ thoracic and lumbar spine, most injuries were fractures and occurred in the lumbar spine area. From the case by case analyses it can be concluded that lumbar spine fractures occur in accidents without the engagement of longitudinals, lateral loading to the occupant and/or very severe accidents with MAIS being much higher than the spine AIS.
The paper gives an overview of the recent (mostly 2012) figures of killed bus/coach occupants (drivers and passengers) in 27 Member States of the European Union as reported by CARE. The Evolution of the figures of bus/coach occupants killed in road accidents urban, rural without motorway and on motorways from 1991 to 2010 in 15 Member States of the EU supplements this information. More detailed are the figures reported for Germany by the Federal Statistics. The paper displays long-term evaluations (1957 to 2012) for killed, seriously and slightly injured occupants in all kinds of buses/coaches. Midterm evaluations (1995 to 2012) of the figures of fatalities and casualties are displayed for different busses according to their identification of road using as coaches, urban buses, school buses, trolley buses and "other buses". To be able to compare the evolutions of the safety of vehicle occupants it is customary to use different risk indicators. Calculations and illustrations for three often used indicators with their development over time are given: fatalities, seriously injured and slightly injured per 100,000 vehicles registered, per 1 billion (109) vehicle-kilometres travelled and per 1 billion (109) person-kilometres. These indicators are shown for occupants of cars, goods vehicles and buses/coaches. For the period from 1957 until 2012 it is obvious, that for all three vehicle categories analysed there was a clear long-term trend towards more occupant safety in terms of casualties per vehicles registered and per vehicle mileage. This was most significant for car occupants but it can be seen for bus/coach occupants and goodsvehicle occupants as well. Figures of killed occupants and of casualties related to person-kilometres are calculated and displayed for the shorter period 1995 to 2012. Here it becomes obvious that the bus/coach is still the safest mode of transport for the occupants of road vehicles. Graphs for the casualty risk indices still show significantly higher risks for car occupants despite the corresponding curve moved sustainable downwards. It is remarkable, that the risks of being killed or injured for the occupants of urban buses is growing whereas the corresponding risk for the occupants of coaches in line traffic tends downwards. The article ends with a short comparison and discussion of the risk indicators which are actually published for the occupants (driver and passengers) of cars and the passengers of buses/coaches, railroads, trams and airplanes. The interpretation of such information depends on the perception and it seems that for a complete view not only one indicator should be used and the evolutions of the indicator values during longer periods (as displayed with examples in the paper) should also be taken into account.
A means of assessing the passive safety of automobiles is a desirable instrument for legislative bodies, the automobile industry, and the consumer. As opposed to the dominating motor vehicle assessment criteria, such as engine power, spaciousness, aerodynamics and consumption, there are no clear and generally accepted criteria for assessing the passive safety of cars. The proposed method of assessment combines the results of experimental safety tests, carried out according to existing legally prescribed or currently discussed testing conditions, and a biomechanical validation of the loading values determined in the test. This evaluation is carried out with the aid of risk functions which are specified for individual parts of the body by correlating the results of accident analysis with those obtained by computer simulation. The degree of conformance to the respective protection criterion thus deduced is then weighted with factors which take into account the frequency of occurrence and the severity of the accident on the basis of resulting costs. Each of the test series includes at least two frontal and one lateral crash test against a deformable barrier. The computer-aided analysis and evaluation of the simulation results enables a vehicle-specific overall safety index as well as partial and individual safety values to be determined and plotted graphically. The passive safety provided by the respective vehicle under test can be defined for specific seating positions, special types of accident, or for individual endangered parts of the body.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Im Jahr 2004 fand an der Medizinischen Hochschule Hannover die erste ESAR-Konferenz (Expert Symposium on Accident Research) statt. Die Idee einer internationalen Konferenz war aus der Notwendigkeit entstanden, diejenigen Experten zusammen zu bringen, die weltweit tätig sind und Verkehrsunfälle wissenschaftlich analysieren, um ihre Ergebnisse gemeinsam zu diskutieren und einem Zielpublikum von Behördenvertretern, Entwicklungsingenieuren der Automobilindustrie und anderen Wissenschaftlern darzubringen. Die durch Professor Otte initiierte und nun zum vierten Male organisierte Konferenz fand eine breite Akzeptanz und ist mittlerweile Bestandteil einer Konferenzlandschaft mit Zielvorträgen von der Fahrzeugsicherheit bis hin zur Verletzungsanalyse und den Unfallursachen. ESAR kann als wissenschaftliches Kolloquium und Plattform für einen Informationsaustausch der Unfallforscher angesehen werden, die sich speziell mit Methoden der Unfalluntersuchung, mit Verletzungsmechanismen und der Bewertung von Verletzungen, Unfallursachen und anderen Bereichen der statistischen Unfalldatenanalyse befassen. Experten aus den Bereichen der Medizin, der Verkehrspsychologie und der Technik sowie Vertreter zuständiger Behörden kommen hier zusammen, um die Erfahrungen in der Unfallprävention und der Unfallrekonstruktion zu diskutieren und um der Forschung neue Felder zu eröffnen. Neben den Belangen der Europäischen Gemeinschaft werden auch die weltweit zu registrierenden hohen Verletztenzahlen berücksichtigt. Wissenschaftliche Vorträge aus aller Welt tragen dazu bei, geeignete Maßnahmen und Methoden zur Analyse und drastischen Verringerung der Zahl der bei Verkehrsunfällen Getöteten zu entwickeln. Die Zusammensetzung des Teilnehmerkreises dieser wie früherer ESAR-Konferenzen hat längst eine über Europa hinausgreifende Internationalitaet erreicht und bietet daher einen aufschlussreichen Überblick über die verschiedenen Standards bestehender Verkehrssicherheit und unterschiedlichen Unfallszenarien und über die Anforderungen an die Unfallanalysen. Die Ergebnisse langjähriger Forschungsarbeiten in Europa, USA, Australien und asiatischen Ländern beinhalten unterschiedliche infrastrukturelle Zusammenhänge und geben Erkenntnisse über Population, Fahrzeugbestand und Fahrereigenschaften. Derartige Informationen bilden eine exzellente Basis für abzuleitende Empfehlungen und Maßnahmen für die Erhöhung der Verkehrssicherheit international.
The role of a national motor vehicle crash causation study-style data set in rollover data analysis
(2010)
On 1 January 2005, The National Highway Traffic Safety Administration, an agency of the United States Department of Transportation, implemented a new data collection strategy designed to assess crash avoidance technologies and report associated behavioral inputs and outcomes. The original goal was a six-year program, however, during the shortened data collection period; it proved a valuable resource for understanding a precrash environment previously obscured by forensic case investigation. Another unintended consequence was an overlap with infrastructure, roadway geometry, and design with the occupant and vehicle outcomes, by virtue of well-defined attributes. External to the collected data, supplementary information was extrapolated, by using manuals published in the United States, by the American Association of State Highway Transportation Officials and selected State Departments of Transportation, in conjunction with the National Motor Vehicle Crash Causation Study (NMVCCS). This provided a backdrop to the infrastructure framework of the rollover problem within which the occupant and vehicle outcomes were studied. If a NMVCCS-style data collection were to be implemented elsewhere, then complementary manuals produced by federal transportation officials might be consulted producing similar relationships. The current study uses NMVCCS data to describe vehicles travelling through diverse design geometries and the outcome for occupants involved in crashes within that system. Codified and extrapolated data form the basis for assessing NMVCCS and its value to the transportation safety community, as the protocols are applicable universally. The benefit in continuing a NMVCCS-style study is noted, as the interaction of roadway infrastructure and occupant protection agencies might find paths to better work together in solving the complex rollover problem using a common data-driven approach.
The overall purpose of the ASSESS project is to develop a relevant and standardised set of test and assessment methods and associated tools for integrated vehicle safety systems, primarily focussing on currently available pre-crash sensing systems. The first stage of the project was to define casualty relevant accident scenarios so that the test scenarios will be developed based on accident scenarios which currently result in the greatest injury outcome, measured by a combination of casualty severity and casualty frequency. The first analysis stage was completed using data from a range of accident databases, including those which were nationally representative (STATS19, UK and STRADA, SE) and in-depth sources which provided more detailed parameters to characterise the accident scenarios (GIDAS, DE and OTS, UK). A common analysis method was developed in order to compare the data from these different sources, and while the data sets were not completely compatible, the majority of the data was aligned in such a way that allowed a useful comparison to be made. As the ASSESS project focuses on pre-crash sensing systems fitted to passenger cars, the data selected for the analysis was "injury accidents which involved at least one passenger car". The accident data analysis yielded the following ranked list of most relevant accident scenarios: Rank Accident scenario 1 Driving accident - single vehicle loss of control 2 Accidents in longitudinal traffic (same and opposite directions) 3 Accidents with turning vehicle(s) or crossing paths in junctions 4 Accidents involving pedestrians The ranked list highlights the relatively large role played by "accidents in longitudinal traffic", and "accidents with turning vehicle(s) or crossing paths in junctions" (the second and third most prevalent accident scenarios, respectively). The pre-crash systems addressed in ASSESS propose to yield beneficial safety outcomes with specific regard to these accident scenarios. This indicates that the ASSESS project is highly relevant to the current casualty crash problem. In the second stage of the analysis a selection of these accident scenarios were analysed further to define the accident parameters at a more detailed level .This paper describes the analysis approach and results from the first analysis stage.
This work aims at bringing evidence for mass incompatibility in frontal impact for cars built according to the UNECE R94 regulation. French national injury accidents database census for years 2005 to 2008 were used for the analysis. The heterogeneity of frontal self-protection among cars of different masses is investigated, as well as the partner protection parameter offered by these cars. The last part of the analysis deals with the estimation of the benefit, in terms of fatal and severe injuries avoided, if crashworthiness was harmonized for the whole fleet of vehicle. This calculation is done for France and is extended to all Europe.
Estimation of the benefits for the UK for potential options to modify UNECE Regulation No. 95
(2010)
The side impact problem in Europe remains substantial. UK data shows that between 22% and 26% of car occupant casualties are involved in a side impact, but this rises to between 29% and 38% for those who are fatally injured. This indicates the more injurious nature of side impacts compared with frontal impacts. The European Enhanced Vehicle safety Committee (EEVC) has performed work to address the side impact issue since 1979. As part of its continuing work, it has recently investigated potential options for regulatory changes to improve side impact protection in cars further. To support this work the UK undertook an analysis to estimate the benefit for potential options to modify UNECE Regulation 95. The analysis used the UK national STATS19 and detailed Co-operative Crash Injury Study (CCIS) accident databases. Of the potential options reviewed, it was found that the addition of a pole test offered the greatest benefit.
Since 2005, the motorcycle crash fatalities in the US exceeded 10% of the overall annual traffic fatalities. Consequently, it has become critical to gain in-depth understanding of the factors and characteristics contributing to motorcycle crashes. Unfortunately, there currently exists no database gathering the necessary information for an in-depth analysis of the US motorcycle crashes. So this study utilizes the NASS/CDS database (National Automotive Sampling System, Crashworthiness Data System) in order to gain insights into the patterns and factors leading to a NASS/CDS motorcycle crash, from 1997 to 2007. NASS/CDS samples about 5,000 passenger car tow-away crashes per year. Each case includes photographs and detailed data on crash and pre-crash characteristics, vehicle types, trajectories, types of impact, and other pertinent roadway and crash scene information, allowing an in-depth investigation of the crash mechanisms. However, the NASS/CDS sampling process specifically focuses on passenger car crashes, so the cases extracted only correspond to crashes in which a passenger vehicle was towed, and a motorcycle was somehow involved. Thus, a by-hand in-depth review of about 200 cases allowed retrieving 106 relevant crashes for this study, tending to represent the severe passenger vehicle(s) versus motorcycle(s) crashes on US roads. The findings lead to the conclusion that these crashes mostly result from the low conspicuity of the motorcycle, and from the inability of the car drivers to fully appreciate and anticipate the behavior of a motorcycle. Indeed, it has been shown that, first, the car drivers involved in these cases did not attempt any avoidance maneuver, second, they were largely of ages under 25, and finally, the majority of the crashes were in an intersection scenario. In addition, the two major scenarios unveiled were the car attempting a left turn from the opposite direction and the car attempting a left turn from the right. The paper mentions several solutions to enhance the motorcycle- conspicuity and to allow the car drivers to better anticipate its behavior, which seem to be key factors in the intersection-related crashes (and more generally in the passenger vehicle(s) versus motorcycle(s) crashes).