Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (49)
- Buch (Monographie) (29)
- Wissenschaftlicher Artikel (4)
- Teil eines Buches (Kapitel) (2)
- Bericht (2)
Schlagworte
- Simulation (86) (entfernen)
Institut
- Sonstige (86) (entfernen)
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
In recent years the boundaries between active and passive safety blurred more and more. Passive safety in the traditional term includes all safety aspects to prevent occupants to be injured or at least injury severity should be reduced. Passive Safety starts with the collision (first vehicle contact) and ends with rescue (open vehicle doors). Within this phase the occupant has to be protected by the passenger compartment whereby no intrusion should occur. Active safety on the other side was developed to interact prior to the collision whereby the goal is to prevent accidents. The extensive interaction between active and passive safety led to the terminologies "Primary" and "Secondary" safety whereas the expression Integrated Safety Concept was generated. Within this study the most well documented single vehicle accidents with cars not equipped with ESP were identified from the PENDANT database and reconstructed. Additional cases were found in the database ZEDATU of TU Graz. In comparison each case was simulated with the assumption that the cars were equipped with ESP. The differences regarding accident avoidance or crash severity as well as reduction of injury risk were analysed.
Accidents involving two wheels vehicles represent one of the more important types of accidents in Europe. These accidents are usually not easy to reconstruct specially for the analysis of the injuries and its correlation with accident dynamics and evidences. Different methodologies are applied in this work for the reconstruction of two wheeler accidents, especially accident involving motorcycles. From the typologies of road evidences like skid marks, to the use of Pc-Crash and the use of Madymo models, different reconstruction of real accidents are presented. One of the questions that sometimes arise for legal purposes when some type of head injuries arise is if the occupant was wearing or not a helmet. The correlation of head injuries with the use of the helmet is a very important issue, therefore an important legal aspect. One of the key questions for the reconstructions that is difficult to analyze, is if the vehicle occupant, was or not, wearing the helmet. Based on the previously collected information, a generic model of a helmet was developed on CAD 3D, followed by its conversion into finite elements, all in order to perform impact tests using the Madymo software that would help improve the helmet- safety, but that also can be used as a tool in accident reconstruction.
Since a number of human models have been developed it appears sensible to use these models also in the accident analysis. Especially the understanding of injury mechanisms and probably even injury risk curves can be significantly improved when interesting accidents are reconstructed using human body models. However, an important limitation for utilising human models for accident reconstruction is the effort needed to develop detailed FE models of the accident partners or to prepare the human model reconstruction by running physical accident reconstructions. The proposed approach for using human models for accident reconstruction is to use simplified and parametric car models. These models can be adapted to the crash opponents in a fast and cost effective way. Although, accuracy is less compared to detailed FE models, the relevant change in velocity can be simulated well, indicating that the computation of a detailed crash pulse is not needed. Two frontal impact test accidents that were reconstructed experimentally and using the parametric car models are indicating sufficient correlation of the adapted parametric car models with the full scale crash reconstructions. However, further developments of the parametric models to be capable for the use in lateral impacts and rear impacts are needed. For the PC Crash simulation runs the output sampling rate is too large to allow sufficient analysis. In addition the performance appears to be too general.
Die Reduzierung des Verkehrslärms ist eine große Herausforderung für alle Beteiligten. Das gilt umso mehr, als nach den Prognosen sich die Verkehrsleistung auf der Straße noch stark erhöhen wird. Viele Stellen in Deutschland, wie Industrie, Forschungseinrichtungen und Behörden haben sich der Problematik angenommen. Forschungsarbeiten wurden und werden durchgeführt oder sind in Vorbereitung. Über die nationalen Aktivitäten hinaus wird das Thema europaweit behandelt. In vier Beiträgen wird über die europäischen Forschungsprojekte SILVIA, ITARI, SILENCE und P2RN berichtet. Das Spektrum der Konzepte dieser Forschungsarbeiten ist sehr breit und erstreckt sich über praktische und theoretische Ansätze.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
Detailed investigations and reconstructions of real accidents involving vulnerable road users
(2005)
The aim of this research is to improve knowledge about vulnerable road users accidents and more specifically pedestrians or cyclists. This work has been based on a complete analysis of real accidents. From accidents chosen from an in-depth multidisciplinary investigation (psychology, technical, medical), we have tried to identify the configuration of the impact: car speed, pedestrian or cyclist orientations. Then, we have made a numerical modelling of the same configuration with a multibody software. In particular, we have reproduced the anthropometry of the victim and the front shape of the car. A first simulation has been performed on this starting configuration. Next, effects of some parameters such as car velocity or victim position at impact have been numerically studied in order to find the best correlations with all indications produced by the in-depth analysis. Finally, the retained configuration was close to the presumed real accident conditions because it reproduces in particular the same impact points on the car, the same injuries, and is according to the driver statement. This double approach associating an in-depth accident analysis and a numerical simulation has been applied on pedestrian-to-car and bicyclist-tocar accidents. It has allowed us to better understand the real kinematics of such impacts. Even if this method is based on a case to case study, it underlines which parameters are relevant on a vulnerable road user accident investigation and reconstruction.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
Im Projekt ESIMAS - Echtzeit-Sicherheits-Management-System für Straßentunnel - wurde der Prototyp für ein Expertensystem zur Überwachung von Straßentunneln unter Einbezug innovativer Detektionssysteme entwickelt. Das Ziel von ESIMAS ist die Bereitstellung eines ganzheitlichen modularen Ansatzes zur Überwachung von Straßentunneln, welcher sowohl die präventive Ereignisvermeidung, die schnelle Ereigniserkennung als auch die Ereignisbewältigung verbessern soll. Dieser Ansatz geht deutlich über die aktuellen Möglichkeiten der Tunnelsteuerung und übergeordneten Leitsysteme hinaus. Die zukünftige Unterstützung der Überwachung von Tunnelanlagen mit ESIMAS führt zu einem maßgeblichen Sicherheitsgewinn für den Verkehrsteilnehmer, da durch die umfangreichere und genauere Erfassung und Auswertung von Informationen die Verantwortlichen in den Tunnelleitzentralen besser und schneller reagieren können.
Einfluss der veränderten Verkehrsführung bei Ertüchtigungsmaßnahmen auf die Bauwerksbeanspruchungen
(2013)
Im Rahmen von mehreren vorhergehenden Forschungsprojekten wurden vom Forschungsnehmer Untersuchungen zu den Beanspruchungen von Brückenbauwerken infolge des Straßenverkehrs durchgeführt. Die Ergebnisse dieser Untersuchungen führten zu den neuen Verkehrslastannahmen für Straßenbrücken im Eurocode 1, Teil 2 (in Verbindung mit dem deutschen nationalen Anhang) und den Ziellastniveaus in der Nachrechnungsrichtlinie. Im Ergebnis von Nachrechnungen müssen die Bestandsbrücken ertüchtigt oder neu gebaut werden. Ertüchtigung von Autobahnbrücken heißt Bauen unter Verkehr. Auf den Bestandsbrücken ist eine veränderte Verkehrsführung erforderlich. Mit einer veränderten Verkehrsführung geht aber unter Umständen auch eine Veränderung der Beanspruchungen der Brückenbauwerke infolge dieser "Umnutzung" einher. Ziel des vorliegenden Forschungsprojektes ist es, den Einfluss der veränderten Verkehrsführung bei Ertüchtigungsmaßnahmen auf die Bauwerksbeanspruchungen zu analysieren. Unter Anwendung einer in den vorhergehenden Projekten entwickelten Vorgehensweise werden Simulationsrechnungen durchgeführt, in denen verschiedenen Varianten von Spuranordnungen auf Überbauquerschnitten betrachtet werden. Des Weiteren werden differenzierte Verkehrscharakteristiken, also verschiedene Verkehrsstärken und Verkehrszusammensetzungen, betrachtet. Grundsätzlich werden hierbei Beanspruchungen, also zum Beispiel resultierende Biegemomente oder Auflagerkräfte, betrachtet. Aus diesem Grund müssen die Berechnungen für definierte Tragsysteme durchgeführt werden. Im vorliegenden Projekt wurden hierzu zwei reale Brückenbauwerke betrachtet, die sich im Zuge von Autobahnen in Nordrhein-Westfalen befinden. Erweitert werden die Betrachtungen auf ein zusätzliches "virtuelles" Tragsystem, um ein gewisses Spektrum von Stützweiten und Querschnittsbreiten analysieren zu können. Grundsätzlich zeigt sich im Ergebnis der Untersuchungen, dass Beanspruchungen aus aktuellem Verkehr bei normaler Verkehrsführung durch das Lastmodell LM1 des DIN-Fachberichtes 101 abgedeckt werden. Für Beanspruchungen aus zukünftigem Verkehr ist das neue Lastmodell LM1 des Eurocodes erforderlich. Im Rahmen von Baumaßnahmen wird im Allgemeinen eine 4+0-Verkehrsführung eingerichtet. Hierbei werden bei zweiteiligen Überbauquerschnitten vier Fahrstreifen über einen Querschnitt geleitet. Dies geht einher mit einer Verengung der Fahrspuren. In solchen Fällen ist davon auszugehen, dass es nicht möglich ist, dass Lkw-Überholverkehr stattfinden kann. Dies führt zu einer wesentlichen Verringerung der Beanspruchungen von Brückenbauwerken, da auch in Stausituationen in den zwei Richtungsfahrbahnen keine Lkw-Fahrzeuge nebeneinander stehen können. Für Verkehrszusammensetzungen entsprechend der aus der Nachrechnungsrichtlinie bekannten Verkehrsart "Große Entfernung" (50 % Sattelzugfahrzeuge) ergibt sich daher eine Abdeckung der Beanspruchungen aus Straßenverkehr durch das Lastmodell BK60 der DIN 1072. Für Verkehrszusammensetzungen analog der Verkehrsart "Mittlere Entfernung" reicht das Lastmodell BK30/30 zu Abdeckung aus. Weitere Differenzierungen hinsichtlich der Verkehrsstärke führen hier zu keinen wesentlichen Änderungen der getroffenen Aussagen.