Abteilung Fahrzeugtechnik
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (90)
- Deutsch (51)
- Mehrsprachig (1)
Volltext vorhanden
- nein (142) (entfernen)
Schlagworte
- Safety (53)
- Sicherheit (53)
- Anfahrversuch (38)
- Vehicle (37)
- Bewertung (36)
- Evaluation (assessment) (36)
- Fahrzeug (36)
- Impact test (veh) (35)
- Test method (31)
- Prüfverfahren (29)
Institut
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
Der Autor berichtet über zwei Forschungsprojekte zur Prüfung von runderneuerten Reifen durch Schnell- und Dauerlaufprüfung. Es wurden Pkw- und Lkw-Reifen mit Karkassen unterschiedlicher Hersteller und unterschiedlichen Alters mit und ohne reparierte Durchstoßschäden untersucht. Die Versuchsergebnisse spechen für eine Altersbegrenzung der rundzuerneuernden Karkassen auf 6 Jahre. Das Reparieren sollte nur bei der Runderneuerung von Lkw-Reifen toleriert werden. Eine Rückstufung der Geschwindigkeitsklassen nach Runderneuerung von Pkw-Reifen zeigt eine positive Wirkung.
A means of assessing the passive safety of automobiles is a desirable instrument for legislative bodies, the automobile industry, and the consumer. As opposed to the dominating motor vehicle assessment criteria, such as engine power, spaciousness, aerodynamics and consumption, there are no clear and generally accepted criteria for assessing the passive safety of cars. The proposed method of assessment combines the results of experimental safety tests, carried out according to existing legally prescribed or currently discussed testing conditions, and a biomechanical validation of the loading values determined in the test. This evaluation is carried out with the aid of risk functions which are specified for individual parts of the body by correlating the results of accident analysis with those obtained by computer simulation. The degree of conformance to the respective protection criterion thus deduced is then weighted with factors which take into account the frequency of occurrence and the severity of the accident on the basis of resulting costs. Each of the test series includes at least two frontal and one lateral crash test against a deformable barrier. The computer-aided analysis and evaluation of the simulation results enables a vehicle-specific overall safety index as well as partial and individual safety values to be determined and plotted graphically. The passive safety provided by the respective vehicle under test can be defined for specific seating positions, special types of accident, or for individual endangered parts of the body.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
Berichtet wird über eine Neufassung des Handbuches zur bürgerfreundlichen und behindertengerechten Gestaltung des Straßenraumes. Ziel dieses Handbuches ist es, die aktuellen nationalen und internationalen Regelungen und Empfehlungen, Normungen und Untersuchungen zu erfassen und für eine behindertengerechte Straßenraumplanung, die für viele behinderte und ältere Menschen erst die Möglichkeit zur Mobilität schafft, nutzbar zu machen.
Die Autoren berichten über den Auftaktworkshop "Empfehlung der Europäischen Kommission über On-board-Informations- und -Kommunikationssysteme: Europäischer Grundsatzkatalog zur Mensch-Maschine-Schnittstelle", der am 7.9.2000 in der Bundesanstalt für Straßenwesen stattfand. Die zuständigen Stellen (wie zum Beispiel die Fahrzeug- und Zulieferindustrie) wurden dazu angehalten, die Empfehlungen zu beachten sowie der BASt über Erfahrungen zu berichten. Dazu wurde mit den Teilnehmern ein erster Gedankenaustausch geführt und das gemeinsame Vorgehen abgestimmt.
Erfahrungen in Deutschland mit der Anwendung der EU-Empfehlung "Europäischer Grundsatzkatalog zur Fahrer-Fahrzeug-Schnittstelle für Informations- und Kommunikationssysteme" werden beschrieben und daraus Konsequenzen abgeleitet. Insgesamt ist die ergonomische Bewertung der Mensch-Maschine-Schnittstelle von Fahrerinformations- und -Kommunikationssystemen nicht als einmaliges Ereignis, sondern als immer wieder zu durchlaufender Vorgang anzusehen, da neben neuen wissenschaftlichen Erkenntnissen jeweils neu entwickelte Geräte und Systeme zu berücksichtigen sind, was eine Anpassung der Grundsätze beziehungsweise eine Öffnung der Grundsätze für technische Neuerungen mit hohem Sicherheitsstandard erfordern könnte. Demonstrationen neuartiger Bedienkonzepte, Systementwicklungen und Arbeitstechniken sowie die hierzu durchgeführten Nutzertests verdeutlichen, dass ergonomisch sehr vielversprechende Lösungen (wie zum Beispiel Schnittstellen, die Eingaben mittels Gestik gestatten) existieren, beziehungsweise sich in der Entwicklung befinden. Diese Lösungen zeigen, dass die Empfehlung in weiten Bereichen technologieabhängig, das heißt, mit Blick auf Neuentwicklungen, nicht erschöpfend ist. Die Weiterentwicklung der Grundsätze sowie die Bewertung der sicheren Gestaltung der Mensch-Maschine-Schnittstelle bedarf nicht nur einer europaweit, sondern weltweit abgestimmten Vorgehensweise.
Es wird über das Ende 2002 abgeschlossene EU-Projekt ADVISORS berichtet. Ziel dieses Projektes, an dem sich 16 Organisationen aus 10 europäischen Ländern beteiligten, war es, die Entwicklung, Testung und Implementierung von Fahrerassistenzsystemen (FAS) zu unterstützen. Es wurde eine umfassende Methodik zur Bewertung von FAS entwickelt und auf dieser Basis wurden eine Reihe von Evaluationsstudien zu ausgewählten FAS durchgeführt. Des Weiteren wurden Implementierungsstrategien für bestimmte FAS entwickelt und mit Experten verschiedener Länder diskutiert.
Sowohl mit dem 3. Road Safety Action Programme der Europäischen Kommission als auch mit dem deutschen Verkehrssicherheitsprogramm werden die verkehrspolitischen Zielsetzungen zur Erhöhung der Verkehrssicherheit in Europa und Deutschland festgelegt. Hierbei muss die passive Fahrzeugsicherheit auch weiterhin eine bedeutende Rolle übernehmen. Es ist jedoch auch festzustellen, dass durch den zunehmenden Einsatz von Elektronik im Fahrzeug die klassischen Bereiche der aktiven und passiven Fahrzeugsicherheit mehr und mehr ineinander greifen. Der Fortschritt in der Elektronik ermöglicht eine Integration der Systeme der aktiven und passiven Sicherheit. Dadurch lässt sich die Fahrzeugsicherheit weiter steigern. Durch die Vernetzung der Systeme lassen sich sogar Kosten einsparen. Der europäische Regierungsausschuss EEVC (European Enhanced Vehicle-safety Committee), die Verbraucherschutzorganisation Euro NCAP (European New Car Assessment Programme) und die Europäische Kommission mit der eSafety Initiative haben diesen Trend erkannt und entsprechende Aktivitäten eingeleitet.
Die Gestaltung der Interaktion zwischen den elektronischen "Infotainment"-Systemen im Auto und dem Fahrer gewinnt zunehmend an Bedeutung für die Verkehrssicherheit. Dem positiven Nutzen, den die Systeme hinsichtlich Fahrerunterstützung und Fahrkomfort aufweisen, stehen möglicherweise negative Auswirkungen auf die Fahrsicherheit gegenüber, wenn Ablenkung und Überlastung des Fahrers auftreten. Diesem Problemfeld widmete sich das EU-Projekt "Communication Multimedia Unit Inside Car" (COMMUNICAR), das im Juni 2003 abgeschlossen wurde. Hauptziel des Projekts waren die Entwicklung und Evaluierung eines Systems, das den Fahrer bei der Bewältigung der eingehenden Informationen unterstützt und eine zentrale Bedienmöglichkeit aufweist. Das COMMUNICAR-System enthält folgende wesentliche Elemente: Verschiedene Funktionen zu Telematikdiensten, Unterhaltung und zur digitalen Darstellung der traditionellen Informationen; eine als Informationsmanager (IM) bezeichnete regelbasierte Filterlogik sowie eine multimediale integrierte Mensch-Maschine-Schnittstelle (MMS) zur zentralen Bedienung und Informationsausgabe. In der ersten Phase der Entwicklung wurden die Nutzeranforderungen analysiert, die Funktionen definiert und die Ein-/Ausgabemodalitäten festgelegt. In der zweiten Phase wurden virtuelle Prototypen zur Gestaltung der MMS erarbeitet und diese in den anschließenden Nutzertest im Labor bewertet und ausgewählt. Die dritte Phase diente der Systementwicklung, bei der es vor allem um die Filterlogik des IM ging. Das System wurde zunächst im Fahrsimulator, anschließend unter Feldbedingungen getestet. Die Ergebnisse, die in den wesentlichen Einzelheiten berichtet werden, zeigten insgesamt ein positives Bild sowohl hinsichtlich der subjektiven Akzeptanzbewertung als auch hinsichtlich des Fahrverhaltens.
Die amtliche Straßenverkehrsunfallstatistik kann nur in begrenztem Umfang Informationen zu Unfallentstehung, Unfallablauf sowie zu den zugrunde liegenden Verletzungsmechanismen bereitstellen. Verbleibende Informationslücken lassen sich durch spezielle Erhebungsteams schließen, die Verkehrsunfälle nach wissenschaftlichen Aspekten dokumentieren. Hierzu unterhalten das Bundesministerium für Verkehr, Bau- und Wohnungswesen und die Bundesanstalt für Straßenwesen seit 30 Jahren ein Forschungsprojekt zur Unfalldatenerhebung an der Medizinischen Hochschule Hannover. Seit 1999 erfolgt eine Kooperation mit der Forschungsvereinigung Automobiltechnik (FAT), die ein weiteres Erhebungsteam an der Technischen Universität Dresden unterhält. Die Unfalldaten gehen in die gemeinsame GIDAS-Datenbank ein, aus der sich umfassende Informationen zu den breit gefächerten Forschungsfeldern "Passive und aktive Fahrzeugsicherheit", "Verkehrs- und Rettungsmedizin" und "Straßenbezogene Sicherheitsfragen" gewinnen lassen. In der Zukunft werden Unfallvermeidungsstrategien und Unfallursachenprophylaxe im Vordergrund einer prospektiven Unfallforschung stehen. Die Daten werden auch in Zukunft für die weitere Verbesserung der Verkehrssicherheit einen bedeutenden Beitrag leisten.
Abschluss des deutsch-französischen Verbundprojekts "Inter-Vehicle Hazard Warning" (DEUFRAKO-IVWH)
(2004)
Im Rahmen der Deutsch-Französischen Kooperation im Verbundprojekt "Inter-Vehicle Hazard Warning" (DEUFRAKO-IVWH) wurde ein auf Fahrzeug-Fahrzeug-Kommunikation basierendes Warnsystem konzipiert und bewertet. Die im Rahmen des Projekts durchgeführten Arbeiten haben gezeigt, dass ein auf Fahrzeug-Fahrzeug-Kommunikation basierendes Warnsystem prinzipiell geeignet ist, einen Beitrag zur Erhöhung der Verkehrssicherheit zu leisten. Das Ausmaß der zu erwartenden positiven Effekte ist allerdings ganz wesentlich abhängig vom Ausstattungsgrad der Fahrzeugflotte mit einem solchen System.
Der Autor berichtet über das neu eingerichtete Expertennetzwerk HUMANIST, das sich mit Fragen der nutzerorientierten und sicherheitsgerechten Gestaltung von Fahrerassistenz- und Informationssystemen befasst. Ziel sind die Zusammenführung und Integration entsprechender Forschungsaktivitäten auf europäischer Ebene.
Am 01.03.2004 wurde auf europäischer Ebene das Expertennetzwerk HUMANIST (HUMAN centred design for Information Society Technologies) eingerichtet, das sich mit Fragen der Implementierung, Gestaltung und Evaluation von Fahrerassistenz- und -informationssystemen aus einer sicherheits- und nutzerorientierten Perspektive befasst. Insgesamt sind 26 Partnerorganisationen aus 15 europäischen Ländern beteiligt. Nach bisher zwei Jahren Laufzeit kann das Netzwerk eine Vielzahl von erfolgreich durchgeführten Veranstaltungen vorweisen (verschiedene werden im Einzelnen aufgeführt). Darüber hinaus wurde ein Post-Graduierten- beziehungsweise ein Post-Doc-Programm ins Leben gerufen. Eine weitere wichtige Initiative bestand in der Beschaffung von Grundlagen für eine gemeinsame Nutzung der bei den beteiligten Partnern vorhandenen Forschungs-Infrastruktur und einer gemeinsam genutzten Datenbasis und virtuellen Arbeitsumgebung. Weiterhin konnten auch wissenschaftliche Ergebnisse erarbeitet werden, die in einigen wesentlichen Ausschnitten dargestellt werden. Dabei handelt es sich um folgende Themen: Nutzerbedürfnisse und Potenziale von Fahrerassistenz- und -informationssystemen; Auswirkung der Nutzung von Fahrerassistenz- und -informationssystemen auf das Fahrverhalten und ihre methodische Erfassung; Fahrerausbildung für die Nutzung von Fahrerassistenz- und -informationssystemen. Abschließend wird auf die im Jahr 2006 geplanten Aktivitäten hingewiesen.
Das Projekt IMPROVER (Impact Assessment of Road Safety Measures for Vehicles and Road Equipment / Wirkungsanalyse und Bewertung von verschiedenen Verkehrssicherheitsmaßnahmen) wurde im Auftrag der Europäischen Kommission (Generaldirektion Energie und Verkehr) bearbeitet, um die folgenden Straßenverkehrssicherheitsaspekte zu untersuchen: den Einfluss der wachsenden Zahl von Sport Utility Vehicles (SUV) und Multi Purpose Vehicles (MPV) auf Verkehrssicherheit, Kraftstoffverbrauch und Emissionen; die Bewertung von Maßnahmen zur Verbesserung der Verkehrssicherheit von leichten Nutzfahrzeugen; die Auswirkungen des Tempomaten auf Verkehrssicherheit, Kraftstoffverbrauch und Emissionen; die Harmonisierung von Verkehrszeichen und Markierungen auf dem Transeuropäischen Straßennetz (TERN) unter Verkehrssicherheitsgesichtspunkten. Das Projekt wurde von der Bundesanstalt für Straßenwesen (BASt) zusammen mit 14 Partnerinstituten von November 2004 bis Mai 2006 bearbeitet. Entsprechend den Aufgaben wurde das Projekt in vier voneinander unabhängige Subprojekte eingeteilt. Der vorliegende Artikel gibt eine Übersicht über die in den jeweiligen Unterprojekten geleisteten Arbeiten, deren Ergebnisse und die daraus abgeleiteten Empfehlungen.
Die Autoren berichten über den Auftaktworkshop "Empfehlung der Europäischen Kommission über On-board-Informations- und -Kommunikationssysteme: Europäischer Grundsatzkatalog zur Mensch-Maschine-Schnittstelle", der am 7.9.2000 in der Bundesanstalt für Straßenwesen stattfand. Die zuständigen Stellen (wie zum Beispiel die Fahrzeug- und Zulieferindustrie) wurden dazu angehalten, die Empfehlungen zu beachten sowie der BASt über Erfahrungen zu berichten. Dazu wurde mit den Teilnehmern ein erster Gedankenaustausch geführt und das gemeinsame Vorgehen abgestimmt.
In den vergangenen 20 Jahren hat der Verkehrslärm an Autobahnen um durchschnittlich 2,5 dB(A), an Bundesstraßen um 1,5 dB(A) zugenommen. Die Absenkung der Geräuschgrenzwerte durch technische Maßnahmen an den Fahrzeugantrieben brachte nicht den gewünschten Erfolg, da außerorts das Reifen-Fahrbahn-Geräusch überwiegt und die Verkehrsmenge generell stark gewachsen ist. Eine Stagnation des Verkehrsaufkommens ist nicht erkennbar, sodass auch in Zukunft neue Straßen in der dicht besiedelten Bundesrepublik nur noch zusammen mit sehr kostenintensiven Lärmschutzmaßnahmen geplant und gebaut werden können. Mit dieser Ausgangslage wurde, als Teil des Forschungsnetzwerkes "Leiser Verkehr", das Verbundprojekt "Reduzierte Reifen-Fahrbahn-Geräusche" konzipiert. In dem Projekt arbeiten 16 Partner aus Verwaltung, Industrie und Forschung zusammen, um zum einen die theoretischen Grundlagen bei der Entstehung und Messung von Reifen-Fahrbahn-Geräuschen zu erarbeiten, zum anderen die Komponenten des Systems "Reifen-Fahrbahn" zu optimieren. Dieses System setzt sich aus den Teilen Reifen, Fahrzeug, Straße (Asphalt-, Betonbauweise) und den Fahrbahnübergängen der Brücken zusammen. Im Rahmen der Projektlaufzeit sollen 1 bis 3 dB(A) leisere Komponenten des geräuscherzeugenden Gesamtsystems entwickelt, erprobt und gebaut werden. Mittelfristig soll durch die Entwicklung von Reifen-Fahrbahn-Geräusch-Modellen ein mindestens 5 dB(A) leiseres Gesamtsystern konzipiert werden. Nach Beginn im Sommer 2001 befindet sich das Projekt momentan in der Arbeitsphase und mit ersten Ergebnissen ist Ende des laufenden Jahres zu rechnen.
Der Beitrag gibt den Inhalt eines Vortrags auf dem Forum des Deutschen Verkehrssicherheitsrats (DVR) 2006 in München wieder. Anhand der folgenden 4 Statements wird eine Einschätzung des möglichen Sicherheitsgewinns durch bisher entwickelte beziehungsweise in der Entwicklung befindliche Fahrerassistenzsysteme vorgenommen: 1) Ein hohes Unfallvermeidungspotenzial besteht für die Funktionen "Kreuzungsassistenz", "Unterstützung bei der Wahl einer situationsangepassten Geschwindigkeit" und "Kollisionswarnung/-vermeidung im Längsverkehr". 2) Ungefähr ein Drittel aller Unfälle kann nur durch aktiv eingreifende Fahrerassistenzsysteme verhindert werden. 3) Die erfolgversprechendsten Assistenzfunktionen sind äußerst komplex, bedürfen noch einigen Entwicklungsaufwands und ihrer Einführung stehen zum Teil erhebliche rechtliche Hürden gegenüber. 4) Ein hohes Sicherheitspotenzial bedeutet nicht unbedingt auch einen tatsächlich hohen Sicherheitsgewinn. Abschließend wird dargelegt, welche Maßnahmen dazu beitragen könnten, die Sicherheitspotenziale von Fahrerassistenzsystemen zu erschließen.
Wegen der wachsenden Verbreitung von Fahrradanhängern zum Kindertransport und der möglichen Unfallgefährdung ist im vorliegenden Forschungsprojekt deren passive Sicherheit untersucht worden. Zudem wurde der Frage nachgegangen, ob der Transport von Kindern im Fahrradanhänger sicherer ist als mit dem Fahrrad mit Kindersitzen. In Absprache mit Herstellern und Vertreibern wurden verschiedene Untersuchungen durchgeführt. Es handelte sich um Anprallversuche (Anfahrversuche), Rollwagenversuche (Schlittenversuche) sowie Kopffreiheitsprüfungen und Fallversuche. Bei den Versuchen waren die Prüfobjekte mit einem oder zwei Dummies besetzt, die mit Messdatenaufnehmern ausgestattet waren. Verschiedene Messdaten, zum Beispiel Kopf- und Brustbeschleunigung, wurden erfasst und ausgewertet. Zusätzlich wurde das Kopfschutzkriterium (HPC) berechnet und bewertet. Entstandene Schäden an den Prüfobjekten wurden aufgenommen und durch Fotos dokumentiert. Die Versuchsabläufe selbst wurden mit Hochgeschwindigkeitskameras aus verschiedenen Positionen aufgezeichnet. Beim Anfahrversuch mit einem Pkw gegen ein Gespann aus Fahrrad und Anhänger waren direkte Anstöße der Anhängerinsassen an die Pkw-Front zu erkennen. Die Beschleunigungswerte waren dabei relativ hoch. Anstöße gegen Anhängerinnenteile waren bei fast allen Versuchen zu beobachten. Teilweise wurden Radaufhängungen und Radnaben beschädigt. Durch die Rollwagenversuche wurden konstruktive Schwächen bei den Sitzen und Rückhaltesystemen festgestellt. Nähte, Befestigungen und Verstellösen wurden zerstört. Es stellte sich heraus, dass die Qualität des Gurtsystems, die Steifigkeit des Anhängeraufbaus, die Sitzposition der Kinder und die vorhandene Kopffreiheit ausschlaggebend für das Verletzungsrisiko der Insassen sind. Bei den Versuchen mit Fahrradsitzen ergaben sich hohe Beschleunigungswerte durch den direkten Kontakt des Radfahrers mit der Fahrzeugfront und/oder der Fahrbahn. Das Gewicht des Radfahrers, des Fahrrades und auch Fahrradteile bergen ein erhöhtes Verletzungsrisiko für das Kind. Zusätzlich besteht die Gefahr überfahren zu werden, wenn das Kind nach dem Sturz des Fahrrades ungeschützt auf der Fahrbahn liegt. Ein direkter Vergleich der beiden Transportmöglichkeiten war aufgrund der geringen Daten der Versuche mit Fahrradkindersitzen nur bedingt möglich. Tendenziell ist der Transport der Kinder im Fahrradanhänger als weniger gefährlich zu bewerten. Es werden die Vor- und Nachteile dargestellt. Zur Bewertung der Sicherheit von Fahrradanhängern wurden die folgenden Prüfmethoden erarbeitet: - Pendelschlagprüfung für die gesamte Chassisstruktur; - Kopffreiheitsprüfung; - Belastungsprüfung der Aufbaustruktur; - Festigkeitsprüfung der Gurtsysteme. Die Prüfungen sind so aufgebaut, dass sie mit einfachen Mitteln durchzuführen sind. Es sollte somit jedem Anhängerhersteller möglich sein, die passive Sicherheit seiner Produkte umfassend zu untersuchen. Die Prüfverfahren für die Sicherheitsbewertung sollen in eine DIN-Norm und in das Merkblatt für Fahrradanhänger einfließen. Der Original-Forschungsbericht enthält einen umfangreichen Fotoband zu den Einzelheiten der Versuche und Versuchsaufbauten sowie zu den Beschädigungen der Prüfobjekte und kann bei der BASt eingesehen werden.
Die Schwingungsdämpfer von Pkw werden in Deutschland bei der regelmäßigen technischen Überwachung im Rahmen der Hauptuntersuchung nach Paragraph 29 StVZO überprüft. In eingebautem Zustand werden sie dabei im wesentlichen nur einer Sichtkontrolle unterzogen, bei der die Dichtigkeit der Dämpfer und ihre äußerliche Unversehrtheit beurteilt werden. Ziel der Untersuchung war die Klärung der Frage, ob die Notwendigkeit einer aussagekräftigeren Kontrolle der Schwingungsdämpfer bei der regelmäßigen technischen Überwachung von Kraftfahrzeugen besteht, da die objektive Messung der Dämpferleistung problematisch ist und der Nutzen einer solchen Maßnahme bisher nicht quantifiziert werden kann. Objektive Prüfergebnisse an Schwingungsdämpfern sind jedoch nur in ausgebautem Zustand zu erhalten. Durch die Untersuchung sollte über eine "Ist-Zustands-Prüfung" von im Verkehr befindlichen Pkw und eine darauf aufbauende Hochrechnung der Anteil der Fahrzeuge, die mit defekten Dämpfern fahren, festgestellt werden. Die Auswertung der Reihenuntersuchung ergab, dass von 5.749 untersuchten Pkw 450 Pkw eine Fahrwerksbeurteilung erhielten, nach der an mindestens einem Rad der prüfstandspezifische Grenzwert nicht eingehalten wurde, was in der Regel auf einen defekten Dämpfer zurückzuführen ist. Dies entspricht hochgerechnet einem Anteil von 7,8 Prozent der zugelassenen Pkw. Folgt man den durch die Reihenuntersuchung ermittelten Ergebnissen und den bisher diskutierten Grenzwerten von 50 Prozent für die Restwirkung der Dämpfer, so würde die Einführung einer obligatorischen Dämpferprüfung zu erheblichen Kosten führen, deren Nutzen jedoch aufgrund fehlender Angaben derzeit nicht festgestellt werden kann. In Anbetracht der Unsicherheiten bezüglich des Einflusses defekter Schwingungsdämpfer auf das Unfallgeschehen und der ermittelten Defektrate konnte die Einführung einer obligatorischen Prüfung auf einem Prüfstand im Rahmen der regelmäßigen Hauptuntersuchung nicht abschließend bewertet werden.
In der Europäischen Gemeinschaft werden derzeit jährlich ca. 50.000 Menschen bei Verkehrsunfällen getötet, ca. 10.000 davon als Fußgänger. Von den 10.600 (1992) in der Bundesrepublik Deutschland bei Straßenverkehrsunfällen Getöteten waren 1.800 Fußgänger (etwa 17 Prozent). Problemgruppen bei Fußgängerunfällen bilden die Kinder wegen ihrer hohen Unfallhäufigkeit und alte Personen wegen ihrer hohen Unfallschwere. Kopfverletzungen sind die häufigste Todesursache bei Fußgängerunfällen. Eine Verringerung der Unfallschwere kann - außer durch Verminderung von Fahr- beziehungsweise Aufprallgeschwindigkeiten der Fahrzeuge - nur durch konstruktive Eingriffe an der vorderen Fahrzeugaußenkontur oder dem Unterbau von Pkw erfolgen. Dazu ist es notwendig, einheitliche Prüfverfahren für die Beurteilung der "Fahrzeugaggressivität" gegenüber Fußgängern bereitzustellen. Die Ableitung eines Prüfvorschlages zur Simulation des Kopfaufpralls auf Fronthauben von Pkw beim Fußgängerunfall, unterteilt in Kopfaufpralltests für Erwachsene und Kinder, ist Gegenstand dieser Arbeit. Es werden, ausgehend von einer Analyse der Unfallstatistik, der Entstehungsmechanismus von Kopfverletzungen erklärt, die für ein Prüfverfahren notwendigen Eingangsparameter (Masse, Geschwindigkeit, Aufprallstellen am Fahrzeug etc.) abgeleitet und die Ergebnisse der gewählten Prüfkörpertestmethode mit Ergebnissen von Leichenversuchen verglichen. Eine Kosten-/Nutzen-Betrachtung am Schluss der Arbeit zeigt, dass sich bei nur geringen Kosten ein volkswirtschaftlicher Nutzen durch eine allgemeine Anwendung des Prüfverfahrens mit ca. 270 Millionen DM allein in der Bundesrepublik Deutschland pro Jahr erzielen ließe.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
When the EEVC proposed the full-scale side impact test procedure, it recommended that consideration should be given to an interior headform test in addition. This was to evaluate areas of contact not assessed by the dummy. EEVC Working Group 13 has been researching the parameters of a possible European headform test procedure in four phases. Earlier stages of the research have been presented at previous ESV conferences. The conclusions from these have suggested that the US free motion headform should be used in any European test procedure and that it should be a free flight test, not guided. This research has now culminated in proposals for a European test procedure. This paper presents the proposed EEVC side impact interior headform test procedure, giving the rationale for the test and the first results from the validation phase of the test protocol.
The development of tyre- and truck-manufacturers leads to the direction to introduce wide base single tyres (size 495/45R22,5) instead of twin tyres on the driving axle of trucks, tractors and busses. To study the driving behaviour and safety of various trucks and units with different tyre combinations and loading conditions was the aim of the study. A computer-aided simulation was used for this investigation. Drive tests with a 40 t unit with prototype single tyres on the drive axle were carried out to verify the simulation. Alterations in driving behaviour and driving safety are mainly dependent on the tyre cornering stiffness. The prototype wide single tyres had a higher lateral stiffness which leads to a higher degree of under-steering (safer driving behaviour). The altered spring base on the drive axle had no influence on the side- tilt stability of vehicle combinations but the solo truck profited from the higher rear axle roll stiffness (less danger for roll-over accidents). As far as the driving safety is concerned nothing speaks against wide base tyres on the drive axle. The simulation of a tyre defect in a bend (assuming 40% of the max. transferable side force for the flat tyre) showed no increased danger using wide single tyres. Later driving tests showed however the need of tyre run flat possibilities to avoid jack-knifing of road trains. Also tyre pressure monitoring systems and electronic stability programs for the trucks are advised.
The frontal crash is still an important contributor to deaths and serious injured resulting from road accidents in Europe. As the Hybrid-III dummy used in crash tests is over two decades old, the European Enhanced Vehicle-safety Committee is studying the potential for a new test device. Key is the availability of a well-defined set of requirements that identifies the minimum level of biofidelity required for an advanced frontal dummy. In this paper, a complete set of frontal impact biofidelity requirements, consisting of references , description of test conditions and corridors, is presented.
The Swedish National Road Administration (SNRA), the Japanese Automobile Research Institute (JARI) and the Federal Highway Research Institute (BASt) are co-operating in the International Harmonized Research Activities on Intelligent Transportation Systems (IHRA-ITS). Under this umbrella a joint study was conducted. The overall objective of this study was to contribute to the definition and validation of a "battery of tools" which enables a prediction and an assessment of changes in driver workload due to the use of in-vehicle information systems (IVIS) while driving. In this sense \"validation\" means to produce empirical evidence from which it can be concluded that these methods reliably discriminate between IVIS which differ in terms of relevant features of the HMI-design. Additionally these methods should also be sensitive to the task demands imposed on the driver by the traffic situation and their interactions with HMI-design. To achieve these goals experimental validation studies (on-road and in the simulator) were performed in Sweden, Germany and Japan. As a common element these studies focused on the secondary task methodology as an approach to the study of driver workload. In a joint German-Swedish on-road study the Peripheral Detection Task (PDT) was assessed with respect to its sensitivity to the complexity of traffic situations and effects of different types of navigation systems. Results show that the PDT performance of both the German and the Swedish subjects reflects the task demands of the traffic situations better than those of the IVIS. However, alternative explanations are possible which will be examined by further analyses. Results of this study are supplemented by the Japanese study where informational demands induced by various traffic situations were analysed by using a simple arithmetic task as a secondary task. Results of this study show that relatively large task demands can be expected even from simple traffic situations.
The European Enhanced Vehicle-safety Committee (EEVC) Working Group 13 for Side Impact Protection has been developing an Interior Headform Test Procedure to complement the full-scale Side Impact Test Procedure for Europe and for the proposed IHRA test procedures. In real world accidents interior head contacts with severe head injuries still occur, which are not always observed in standard side impact tests with dummies. Thus a means is needed to encourage further progress in head protection. At the 2003 ESV-Conference EEVC Working Group 13 reported the results on Interior Headform Testing. Further research has been performed since and the test procedure has been improved. This paper gives an overview of its latest status. The paper presents new aspects which are included in the latest test procedure and the research work leading to these enhancements. One topic of improvement is the definition of the Free Motion Headform (FMH) impactor alignment procedure to provide guidelines to minimize excessive headform chin contact and to minimize potential variability. Research activities have also been carried out on the definition of reasonable approach head angles to avoid unrealistic test conditions. Further considerations have been given to the evaluation of head airbags, their potential benefits and a means of ensuring protection for occupants regardless of seating position and sitting height. The paper presents the research activities that have been made since the last ESV Conference in 2003 and the final proposal of the EEVC Headform Test Procedure.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
Powered Two Wheelers (PTWs) accidents constitute one of the road safety problems in Europe. PTWs fatalities represent 22% at EU level in 2006, having increased during last years, representing an opposite trend compared to other road users" figures. In order to reduce these figures it is necessary to investigate the accident causation mechanisms from different points of view (e.g.: human factor, vehicle characteristics, influence of the environment, type of accident). SAFERIDER project ("Advanced telematics for enhancing the SAFEty and comfort of motorcycle RIDERs", under the European Commission "7th Framework Program") has investigated PTW accident mechanisms through literature review and statistical analyses of National and In-depth accident databases; detecting and describing all the possible PTW's accident configurations where the implementation of ADAS (Advanced Driver Assistance Systems) and IVIS (In-Vehicle Information Systems) could contribute to avoid an accident or mitigate its severity. DIANA, the Spanish in-depth database developed by CIDAUT, has been analyzed for that purpose. DIANA comprises of accident investigation teams, in close cooperation with police forces, medical services, forensic surgeons, garages and scrap yards. An important innovation is the fact that before injured people arrive to hospitals, photographs and explanations about the possible accident injury mechanisms are sent to the respective hospitals (via 3G GPRS technology). By this, additional information to medical staff can be provided in order to predict in advance possible internal injuries and select the best medical treatment. This methodology is presented in this paper. On the other hand, the main results (corresponding to road, rider and PTW characteristics; pre and post-accident manoeuvres; road layout; rider behaviour; impact points; accident causations;...) from the analyses of the PTW accidents used for SAFERIDER are shown. Only accident types relevant to ADAS and IVIS devices have been considered.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
The GRSP informal group on child restraint systems (CRS) finalised phase 1 of a new regulation for the homologation of CRS . This regulation is the subject of several discussions concerning the safety benefits and the advantages and disadvantages that certain specific points may bring. However, these discussions are sometimes not based on scientific facts and do not consider the whole package but only single items. Based on the experience of the CASPER partners in the fields of human behaviour, accident analysis, test procedures and biomechanics in the area of child safety, a consideration of the safety benefits of phase 1 of the new regulation and recommendations for phase 2 will be given.
The objective was to develop and validate a crash trolley (reference vehicle) equipped with a compartment and a full restraint system for driver and front seat passenger which can be used in full scale crash testing. Furthermore, the crash trolley should have a suspension to show rotation and nick effects similar to real vehicles. Within the development phase the reference vehicle was build based on a European family car. Special attention was needed to provide appropriate strength to the trolley and its suspension. The reference vehicle is equipped with a restraint system consisting of airbags, pedals, seats, dashboard, and windscreen. On the front of the vehicle different crash barriers can be installed to provide miscellaneous deceleration pulses. For the validation phase a series of low and high speed crash tests with HIII dummies were conducted and compared with full scale tests. For the comparison deceleration pulse, dummy numbers and vehicle movement were analyzed. Validation tests with velocities up to 60 km/h showed promising results. The compartment and the suspension systems stayed stable. Rotation effects were comparable with full scale car crash tests. The airbags and seat belt system worked reasonable. The acceleration pulse compared to an Euro NCAP test had a similar characteristic but was in general slightly lower. After the successful validation the reference vehicle is already in use in different studies in the field of vehicle safety research at BASt.
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of synthetic and plastic materials as a material for the interior equipment of buses and coaches because of their ood mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years - also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, the production of smoke, the smoke development and propagation and its toxicity for the people as well as the testing methods and limit values are of interest. For those reasons research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behavior of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and on-board extinguishing equipment were elaborated. At the other hand research is carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. The paper describes which effective and economically reasonable fire safety requirements for interiors of buses would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses.
Since integrated safety systems combine active and passive safety elements in one safety system, it is necessary to define new procedures to evaluate vehicle safety from the overall system point of view. The main goal of the ASSESS project is to develop harmonized and standardized assessment procedures for collision mitigation and avoidance systems. Methods and Data Sources: In ASSESS, procedures are developed for: driver behaviour evaluation, pre-crash system performance evaluation, crash performance evaluation, socio-economic assessment. This paper will concentrate on the activities related to the crash evaluation. The objective is to perform simulations, sled tests and crash tests in order tounderstand the influence of the activation of the pre-crash systems on the occupants" injuries during the crash phase. When a traffic accident is unavoidable, pre-crash systems work on various safety devices in order to improve the vehicle occupants" protection. Braking assistance and adaptive restraint systems are the main pre-crash systems whose effect on the occupants" protection will be described in this paper. Results: The results will be a description of the effect of the activation of the pre-crash systems on the crash phase. Additionally, a set of recommendations for future methodology developments will be delivered. Furthermore, a first approach to the study of the effect of the pre-crash systems activation on the occupants" protection when the impact is unavoidable will be presented. This effect will be quantified using the biomechanical values obtained from the simulation and testing activities and their related injury risks. Simulation and testing activities will consider the following scenarios: - No activation of any pre-crash system, - Activation of one or a combination of several pre-crash systems. In this way, differences in the results obtained from different scenarios will show the effect of each pre-crash system separately during the crash phase. Discussion and Limitations: The set of activities developed in this research project is limited by the fact that with the given resources only a limited number of vehicle models could be investigated. In addition, there are also limitations related to the injury risk curves and the passive safety tools currently on the market. Conclusion and Relevance to session submitted: The paper will present a complete analysis of the effect of pre-crash systems during the crash phase when the impact is unavoidable. Details, limitations and first application experience based on a few examples will be discussed. Currently, there is not any regulation, assessment program, or other similar official procedure able to assess pre-crash systems during the crash phase. This project comprises phases of traffic accidents which have been historically analysed separately, and aims to evaluate them taking into account their interrelationship. ASSESS is one of the first European projects which deals in depth with the concept of integrated safety, defining methodologies to analyse vehicle safety from a global point of view.
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.