Abteilung Fahrzeugtechnik
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (90)
- Deutsch (51)
- Mehrsprachig (1)
Volltext vorhanden
- nein (142) (entfernen)
Schlagworte
- Safety (53)
- Sicherheit (53)
- Anfahrversuch (38)
- Vehicle (37)
- Bewertung (36)
- Evaluation (assessment) (36)
- Fahrzeug (36)
- Impact test (veh) (35)
- Test method (31)
- Prüfverfahren (29)
Institut
Accidents between right turning trucks and straight driving cyclists often show massive consequences. Accident severity in terms of seriously or fatally injured cyclists that are involved is much higher than in accidents of other traffic participants in other situations. It seems clear that adding additional mirrors will very likely not improve the situation. At ESV 2015, a methodology to derive test procedures and first test cases as well as requirements for a driver assist system to address blind spot accidents has been presented. However, it was unclear if and how testing of these cases is feasible, to what extent characteristics of different truck concepts (e.g. articulated vehicles, rigid vehicles) influence the test conduction and outcome, and what tolerances should be selected for the different variables. This work is important for the acceptance of a draft regulation in the UN working group on general safety. In the meantime, three test series using a single tractor vehicle, a tractor-semitrailer combination and a rigid vehicle have been conducted. The test tools (e.g. surrogate devices) have been refined. A fully crashable, commercially available bicycle dummy has been tested. If used correct, this dummy does follow a straight line quite precisely and it does not cause any damage to the truck under test in case of accidental impact. The dummy specifications are freely available. During testing, the different vehicle categories resulted in different trajectories being driven. Articulated vehicle combinations did first execute a turn into the opposite direction, and on the other hand, single tractor vehicles did behave comparable to passenger cars. A possible solution to take these behaviors into account is to require the vehicles to drive through a corridor that is narrow for a precise straight-driving phase and extends during the turn. Other investigated parameters are the dummy and vehicle speed tolerances. The results from this research make it possible to draft a regulation for a driver assistance system that helps to avoid blind spot accidents: test cases have been refined, their feasibility has been checked, and corridors for the vehicles and for important parameters (e.g. test speeds) have been set. The test procedure is applicable to all types of heavy goods vehicles. In combination with the accidentology (ESV 2015 paper), the work provides the basis for a regulation for such an assistance system.
Advancing active safety towards the protection of vulnerable road users: the PROSPECT project
(2017)
Accidents involving Vulnerable Road Users (VRU) are still a very significant issue for road safety. According to the World Health Organisation, pedestrian and cyclist deaths account for more than 25% of all road traffic deaths worldwide. Autonomous Emergency Braking Systems have the potential to improve safety for these VRU groups. The PROSPECT project (Proactive Safety for Pedestrians and Cyclists) aims to significantly improve the effectiveness of active VRU safety systems compared to those currently on the market by expanding the scope of scenarios addressed by the systems and improving the overall system performance. The project pursues an integrated approach: Newest available accident data combined with naturalistic observations and HMI guidelines represent key inputs for the system specifications, which form the basis for the system development. For system development, two main aspects are considered: advanced sensor processing with situation analysis, and intervention strategies including braking and steering. All these concepts are implemented in several vehicle prototypes. Special emphasis is put on balancing system performance in critical scenarios and avoiding undesired system activations. For system validation, testing in realistic scenarios will be done. Results will allow the performance assessment of the developed concepts and a cost-benefit analysis. The findings within the PROSPECT project will contribute to the generation of state -of-the-art knowledge, technical innovations, assessment methodologies and tools for advancing Advanced Driver Assistance Systems towards the protection of VRUs. The introduction of a new generation safety system in the market will enhance VRU road safety in 2020-2025, contributing to the "Vision Zero" objective of no fatalities or serious injuries in road traffic set out in the Transport White Paper. Furthermore, the test methodologies and tools developed within the project shall be considered for the New Car Assessment Programme (Euro NCAP) future roadmaps, supporting the European Commission goal of halving the road toll in the 2011-2020 timeframe.
Für eine Reihe von EU Regelungen im Bereich Fahrzeugsicherheit erlaubt eine Verordnung bereits seit dem Jahr 2010 virtuelles Testen für die Typzulassungsprüfung. Technische Details bzw. konkrete Prozeduren für spezifische Regelungen sind in dieser Verordnung jedoch nicht enthalten. Das Hauptziel des europäischen Projekts IMVITER (lmplementation of Virtual Testing in Safety Regulations) war es, basierend auf der neuen Verordnung ein virtuelles Testverfahren auszuarbeiten und dabei offene Fragen zu berücksichtigen. Um die im Projekt-Konsortium unter Berücksichtigung der Anliegen aller Interessensgruppen wie Autohersteller, Zulassungsbehörden und technischer Dienste erarbeiteten offenen Punkte zu adressieren, wurde ein generisches Flussdiagramm entwickelt, das den Ablauf einer virtuell basierten Typprüfung darstellt. ln diesem Diagramm ist der virtuelle Typgenehmigungsprozess in drei aufeinander folgende Phasen aufgeteilt, die Verifikations-, Validierungs- und Typgenehmigungsphase. Von entscheidender Bedeutung ist die Phase der Validierung des Simulationsmodells, für die im IMVITER-Projekt eine Methodik vorgeschlagen wurde. Mit der im Projekt vorgeschlagenen Validierungsmethode ist kein Austausch des Simulationsmodells zwischen Fahrzeughersteller und technischem Dienst notwendig, so dass die Vertraulichkeit von Betriebsgeheimnissen nicht gefährdet ist. Zur Validierung des Modells werden jedoch immer Versuche notwendig sein. Dies gilt sowohl für die Überpruefung von passiven als auch aktiven Fahrzeugsicherheitssystemen. Eine zusammenfassende Betrachtung der Erfahrungen aus dem IMVITER-Projekt ergab, dass mit der Einführung von virtuellem Testen keine Erhöhung der Anforderungen an die Fahrzeugsicherheit bzgl. bestehender Regelungen verbunden sein sollte. Jedoch werden auch weiterhin neue zusäztliche Regelungen erforderlich sein, da sich das Unfallgeschehen und die Fahrzeugtechnologie weiterentwickeln und ändern werden. Diese sollten von Beginn an die Möglichkeiten des virtuellen Testens nutzen, insbesondere bei Testverfahren für neue Technologien, z.B. aktiver Fahrzeugsicherheitssysteme. Hier bieten virtuelle Testverfahren nicht nur eine Kosten- oder Zeitersparnis, sondern ermöglichen teilweise erst die sinnvolle Abprüfung von neuen Sicherheitssystemen, die mit aktuellen auf Hardware-Test basierenden Verfahren überhaupt nicht möglich wären.
Automatische Lenkfunktionen sind abgesehen von korrigierenden Lenkeingriffen entsprechend der UN-Regelung Nr. 79 bisher nur in einem Geschwindigkeitsbereich bis 10 km/h erlaubt. Die Weiterentwicklung der Technik im Bereich der Fahrerassistenzsysteme und der Automatisierung der Fahraufgabe wuerden es jedoch technisch erlauben, automatische Lenkfunktionen auch bei höheren Geschwindigkeiten einzusetzen. Neben einem Zugewinn an Komfort wird von diesen Systemen auch ein Beitrag zur Erhöhung der Verkehrssicherheit erwartet. Dieses Verkehrssicherheitspotenzial wird man jedoch nur ausschöpfen können, wenn die automatisierten Lenksysteme entsprechend gestaltet sind. Insbesondere sollten mögliche Risiken auf Grund automatischen Lenkens minimiert sein. Aus diesen Gründen laufen derzeit Arbeiten auf UNECE-Ebene, die Regelung Nr. 79 über einheitliche Bedingungen für die Genehmigung der Fahrzeuge hinsichtlich der Lenkanlage in Bezug auf automatische Lenkfunktionen (ACSF = Automatically Commanded Steering Functions) zu überarbeiten, um diese unter bestimmten Bedingungen auch bei höheren Geschwindigkeiten genehmigen zu können. Der vorliegende Beitrag reflektiert diese Arbeiten und stellt die Entwicklung der technischen Anforderungen an automatisches Lenken und der für die fahrzeugtechnischen Vorschriften vorgesehenen Testprozeduren dar.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben. Das Ergebnis kann indes nicht zufriedenstellen. Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird im Beitrag, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der sich auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschrieben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen; dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
The presence and performance of Advanced Driver Assistance Systems (ADAS) has increased over last years. Systems available on the market address also conflicts with vulnerable road users (VRUs) such as pedestrians and cyclists. Within the European project PROSPECT (Horizon2020, funded by the EC) improved VRU ADAS systems are developed and tested. However, before determining systems" properties and starting testing, an up-to-date analysis of VRU crashes was needed in order to derive the most important Use Cases (detailed crash descriptions) the systems should address. Besides the identified Accident Scenarios (basic crash descriptions), this paper describes in short the method of deriving the Use Cases for car-to-cyclist crashes. Method Crashes involving one passenger car and one cyclist were investigated in several European crash databases looking for all injury severity levels (slight, severe and fatal). These data sources included European statistics from CARE, data on national level from Germany, Sweden and Hungary as well as detailed accident information from these three countries using GIDAS, the Volvo Cars Cyclist Accident database and Hungarian in-depth accident data, respectively. The most frequent accident scenarios were studied and Use Cases were derived considering the key aspects of these crash situations (e.g., view orientation of the cyclist and the car driver- manoeuvre intention) and thus, form an appropriate basis for the development of Test Scenarios. Results Latest information on car-to-cyclist crashes in Europe was compiled including details on the related crash configurations, driving directions, outcome in terms of injury severity, accident location, other environmental aspects and driver responsibilities. The majority of car-to-cyclist crashes occurred during daylight and in clear weather conditions. Car-to-cyclist crashes in which the vehicle was traveling straight and the cyclist is moving in line with the traffic were found to result in the greatest number of fatalities. Considering also slightly and seriously injured cyclists led to a different order of crash patterns according to the three considered European countries. Finally the paper introduced the Use Cases derived from the crash data analysis. A total of 29 Use Cases were derived considering the group of seriously or fatally injured cyclists and 35 Use Cases were derived considering the group of slightly, seriously or fatally injured cyclists. The highest ranked Use Case describes the collision between a car turning to the nearside and a cyclist riding on a bicycle lane against the usual driving direction. A unified European dataset on car-to-cyclist crash scenarios is not available as the data available in CARE is limited, hence national datasets had to be used for the study and further work will be required to extrapolate the results to a European level. Due to the large number of Use Cases, the paper shows only highest ranked ones.
A reduction of around 48% of all road fatalities was achieved in Europe in the past years including a reduced number of fatalities with an older age. However, among all road fatalities, the proportion of elderly is steadily increasing. In an ageing society, the European (Horizon2020) project SENIORS aims to improve the safe mobility of older road users, who have different transportation habits compared to other age groups. To increase their level of safe mobility by determining appropriate requirements for vehicle safety systems, the characteristics of current road traffic collisions involving the elderly and the injuries that they sustain need to be understood in detail. Hereby, the paper focuses on their traffic participation as pedestrian, cyclist or passenger car occupant. Following a literature review, several national and international crash databases and hospital statistics have been analysed to determine the body regions most frequently and severely injured, specific injuries sustained and types of crashes involved, always comparing older road users (65 years and more) with mid-aged road users (25-64 years). The most important crash scenarios were highlighted. The data sources included European statistics from CARE, data on national level from Germany, Sweden, Italy, United Kingdom and Spain as well as in-depth crash information from GIDAS (Germany), RAIDS (UK), CIREN and NASS-CDS (US). In addition, familiar hospital data from Germany (TraumaRegister DGU-®), Italy (Italian Register of Acute Traumas) and UK hospital statistics (TARN) were included in the study to gain further insight into specific injury patterns. Comprehensive data analyses were performed showing injury patterns of older road users in crashes. When comparing with mid-aged road users, all databases showed that the thorax body region is of particularly high importance for the older car occupant with injury severities of AIS 2 or AIS 3+, whereas the body regions lower extremities, head and thorax need to be considered for the older pedestrians and cyclists. Besides these comparisons, the most frequent and severe top 5 injuries were highlighted per road user group. Further, the most important crash configurations were identified and injury risk functions are provided per age group and road user group. Although several databases have been analysed, the picture on the road safety situation of older road users in Europe was not complete, as only Western European data was available. The linkage between crash data and hospital data could only be made on a general level as their inclusion criteria were quite different.
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.
Test and assessment procedures for passive pedestrian protection based on developments by the European Enhanced Vehicle-safety Committee (EEVC) have been introduced in world-wide regulations and consumer test programmes, with considerable harmonization between these programmes. Nevertheless, latest accident investigations reveal a stagnation of pedestrian fatality numbers on European roads running the risk of not meeting the European Union- goal of halving the number of road fatalities by the year 2020. The branch of external road user safety within the EC-funded research project SENIORS under the HORIZON 2020 framework programme focuses on investigating the benefit of modifications to pedestrian test and assessment procedures and their impactors for vulnerable road users with focus on the elderly. Injury patterns of pedestrians and cyclists derived from the German In-Depth Accident Study (GIDAS) show a trend of AIS 2+ and AIS 3+ injuries getting more relevant for the thorax region in crashes with newer cars (Wisch et al., 2017), while maintaining the relevance for head and lower extremities. Several crash databases from Europe such as GIDAS and the Swedish Traffic Accident Data Acquisition (STRADA) also show that head, thorax and lower extremities are the key affected body regions not only for the average population but in particular for the elderly. Therefore, the SENIORS project is focusing on an improvement of currently available impactors and procedures in terms of biofidelity and injury assessment ability towards a better protection of the affected body regions, incorporating previous results from FP 6 project APROSYS and subsequent studies carried out by BASt. The paper describes the overall methodology to develop revised FE impactor models. Matched human body model and impactor simulations against generic test rigs provide transfer functions that will be used for the derivation of impactor criteria from human injury risk functions for the affected body regions. In a later step, the refined impactors will be validated by simulations against actual vehicle front-ends. Prototyping and adaptation of test and assessment procedures as well as an impact assessment will conclude the work of the project at the final stage. The work will contribute to an improved protection of vulnerable road users focusing on the elderly. The use of advanced human body models to develop applicable assessment criteria for the revised impactors is intended to cope with the paucity of actual biomechanical data focusing on elderly pedestrians. In order to achieve optimized results in the future, the improved test methods need to be implemented within an integrated approach, combining active with passive safety measures. In order to address the developments in road accidents and injury patterns of vulnerable road users, established test and assessment procedures need to be continuously verified and, where needed, to be revised. The demographic change as well as changes in the vehicle fleet, leading to a variation of accident scenarios, injury frequencies and injury patterns of vulnerable road users are addressed by the work provided by the SENIORS project, introducing updated impactors for pedestrian test and assessment procedures.
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
Die Initiative der Einführung kooperativer Systeme in einem Korridor von Rotterdam über Frankfurt/Main nach Wien, dem sogenannten C-ITS Corridor, und damit auch in Deutschland wurde im Juni 2013 durch die Unterzeichnung einer entsprechenden Absichtserklärung des Bundesministeriums für Verkehr, Bau und Stadtentwicklung mit den Verkehrsministern der Niederlande und Österreichs offiziell gestartet. In vielen Forschungsprojekten wurden vorher die Grundlagen erarbeitet, um eine solche Einführung technisch überhaupt erst möglich zu machen. Im Beitrag werden diese Ergebnisse nochmals kurz aufgegriffen und um den aktuellen Stand bei den Entwicklungen im C-ITS Corridor erweitert. Als erstes Einführungsszenario wurden die Baustellenwarnung und Kooperatives Verkehrsmanagement unter Einbeziehung von Fahrzeugdaten gewählt. Nicht verschwiegen werden sollen hierbei auch die wesentlichen Herausforderungen, die im Übergang von Forschung und Feldtests zu realen Anwendungen liegen.
Müdigkeit am Steuer ist eine bedeutsame Ursache von Straßenverkehrsunfällen. Es steht eine Fülle unterschiedlicher Methoden zur Verfügung, um Müdigkeit beim Fahrer zu erkennen. Ziel des vorliegenden Projekts war es, auf Basis einer mehrstufigen Befragung von zwölf Experten aus Industrie- und Hochschulforschung die Stärken und Schwächen der derzeit validesten objektiven Müdigkeitsmessverfahren vergleichend zu beschreiben. Als Basis der Bewertung diente ein eigens erarbeiteter Gütekriterienkatalog. Zu den validesten Müdigkeitsmessverfahren gehören aus Expertensicht Lenkverhalten und Spurhaltung, Indikatoren des Lidschlussverhaltens und des EEG, das videobasierte Expertenrating sowie der kontrovers diskutierte Pupillografische Schläfrigkeitstest. Die Güteprofile der sechs ausgewählten Messverfahren werden aufgeführt. Je nach Einsatzgebiet sind alle ausgewählten Messverfahren (Forschung und Entwicklung), nur einige (Müdigkeitswarnsystem im Fahrzeug), oder kein einziges (Verkehrskontrolle) geeignet. Dem Urteil der Experten nach bedarf eine valide Müdigkeitserfassung der Kombination von mindestens zwei Messverfahren unter Berücksichtigung der spezifischen Stärke-Schwächenprofile.
Within the automotive context camera monitor systems (CMS) can be used to present views of the traffic situation behind the vehicle to the driver via a monitor mounted inside the cabin. This offers the opportunity to replace classical outside rearview mirrors and therefore to implement new design concepts, aerodynamically optimized vehicle shapes and to reduce the width of the vehicle. Further, the use of a CMS offers the potential to implement functionalities like warnings or situation-adaptive fields of view that are not feasible with conventional rearview mirrors. Despite these potential advantages, it is important to consider the possible technical constraints of this technology and its effect on driver perception and behavior. On the technical side next to the field of view and die robustness of die system, aspects as its functionality at day and night as well as under varying weather conditions should be object to scientific investigation. Concerning human machine interaction, it has to be considered, that the perception of velocities and distances of approaching vehicles might be different for CMS as compared to conventional rearview mirrors and potential influences of factors as the Position of the displays or drivers' age should be taken into account. In order to shed light on these and further open issues, BASt is currently conducting a study that will cover the use of CMS under controlled conditions as well in real traffic. The first part of the study will focus on passenger cars, while in a second step the empirical investigation will be extended to heavy goods vehicles, where the potentials as well as the limitations of CMS might differ considerably. The presentation will cover the first part, with regard to the experimental design, implementation and initial results if already available.
Economic constraints nowadays require transporting greater volumes of freight at lower cost. Yet, physical profiles of trucks do not all generate the same effects on road infrastructure for a given tonnage hauled. The objective then lies in finding an optimal service level that reduces the damage caused to infrastructure. Results derived for the impact of trucks on pavements are presented. The impact of truck traffic trends on road bridges will also be discussed.rn
Aus wissenschaftlichen Untersuchungen ist bekannt, dass ältere Menschen trotz ihrer langen Fahrerfahrung in spezifischen Verkehrssituationen Fahrfehler und Unsicherheiten zeigen. In zwei Experimenten an jüngeren und älteren Versuchsteilnehmern wurde im Ergonomie-Labor der Bundesanstalt für Straßenwesen (BASt) versucht, den Ursachen spezifischer Fahrfehler älterer Kraftfahrer nachzugehen. Die Ergebnisse lieferten wichtige Ansatzpunkte für die Entwicklung von Fahrerassistenzsystemen (FAS), indem Erkenntnisse zu visuellen Aufmerksamkeitsleistungen gesammelt wurden. Im Rahmen eines Doppeltätigkeitsparadigmas wurde der visuell-räumliche Aufmerksamkeitsprozess, der für das Führen von Kraftfahrzeugen von wesentlicher Bedeutung ist, nicht nur auf der Verhaltensebene, sondern auch neurophysiologisch durch die Ableitung der Hirnströme mittels EEG untersucht. Hauptaufgabe war in beiden Experimenten eine Spurhalteaufgabe, die kurvenreiches Fahren simulieren sollte. Nebenaufgabe war jeweils eine Lichtreizaufgabe, bei der so schnell wie möglich durch Tastendruck auf einen Lichtreiz reagiert werden musste. Im zweiten Experiment wurde überprüft, ob bei der Lichtreizaufgabe die Verschlechterung der Aufmerksamkeitsleistung graduell erfolgt, indem bei den Lichtreizen die Exzentrizität erweitert wurde. Die Reize wurden bilateral, in abgestufter Form in verschiedenen Sehwinkeln von der Fovea centralis präsentiert. Dargestellt werden die Versuchsdurchführung sowie die Ergebnisse für die Verhaltensdaten und die festgestellten ereigniskorrelierten Potenziale (EKP). Es zeigte sich, dass durch die Berücksichtigung zusätzlicher weiterer Exzentrizitäten die Ergebnisse der Vorgängerstudie in bedeutsamer Weise erweitert werden konnten. Für beide Gruppen zeigten sich über den Verlauf hinweg klare Anzeichen für den Verlauf kompensatorischer Prozesse, die sich für die Älteren aber nur bis zu einem Sehwinkel von 50 Grad darstellten. Bei Reizen im Sehwinkel von 60 Grad war die Detektionsleistung deutlich schlechter, vor allem bei den älteren Versuchsteilnehmern. Außerdem wurde festgestellt, dass vor allem die Älteren Beeinträchtigungen in der Detektionsleistung zeigen, wenn der Abstand zwischen zwei Reizen gering ist. Es zeigt sich, das im Hinblick auf das Übersehen von Verkehrsobjekten, das eine wesentliche Ursache von Unfällen älterer Fahrer darstellt, diese technisch - beispielsweise bei Wende- oder Abbiegeprozessen - durch einen Sehfeldassistenten unterstützt werden können. Da Ältere durch schnelle Reaktionsabfolgen stärker beansprucht werden, sind Systeme mit Warnfunktion oder teilautomatisierte Systeme eher kritisch zu sehen, da sie zusätzlichen Bedien- beziehungsweise Überwachungsaufwand erfordern.
To improve vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility aims to improve both the self and partner protection properties of vehicles. Although compatibility has received worldwide attention for many years, no final assessment approach has been defined. Within the Frontal Impact and Compatibility Assessment Research (FIMCAR) project, different frontal impact test procedures (offset deformable barrier [ODB] test as currently used for Economic Commission for Europe [ECE] R94, progressive deformable barrier test as proposed by France for a new ECE regulation, moveable deformable barrier test as discussed worldwide, full-width rigid barrier test as used in Federal Motor Vehicle Safety Standard [FMVSS] 208, and full-width deformable barrier test) were analyzed regarding their potential for future frontal impact legislation. The research activities focused on car-to-car frontal impact accidents based on accident investigations involving newer cars. Test procedures were developed with both a crash test program and numerical simulations. The proposal from FIMCAR is to use a full-width test procedure with a deformable element and compatibility metrics in combination with the current offset test as a frontal impact assessment approach that also addresses compatibility. By adding a full-width test to the current ODB test it is possible to better address the issues of structural misalignment and injuries resulting from high acceleration accidents as observed in the current fleet. The estimated benefit ranges from a 5 to 12 percent reduction of fatalities and serious injuries resulting from frontal impact accidents. By using a deformable element in the full-width test, the test conditions are more representative of real-world situations with respect to acceleration pulse, restraint system triggering time, and deformation pattern of the front structure. The test results are therefore expected to better represent real-world performance of the tested car. Furthermore, the assessment of the structural alignment is more robust than in the rigid wall test.
Verschiedene Forschungsprojekte aus dem Bereich Kooperativer Systeme, die vor Kurzem gestartet sind, beschäftigen sich unter anderem mit den organisatorischen Aspekten einer Gesamtarchitektur. Eine Organisationsarchitektur beschreibt dabei die Rollen und Verantwortlichkeiten, die im Betrieb unterschiedlicher Kooperativer Anwendungen auftreten. In den Projekten erfolgt zumeist eine Betrachtung der Organisationsarchitektur anhand konkreter Implementierungsszenarien oder Use Cases. Der im Bericht dokumentierte aktuelle Stand der abstrakten Beschreibung der Rollen und Verantwortlichkeiten soll den Projekten und Initiativen als Diskussionsgrundlage und Ausgangspunkt für die Erarbeitung einer möglichen Organisationsarchitektur Kooperativer Systeme und deren Ausgestaltung dienen.
The strong prevalence of human error as a crash causation factor in motorcycle accidents calls for countermeasures that help tackling this issue. Advanced rider assistance systems pursue this goal, providing the riders with support and thus contributing to the prevention of crashes. However, the systems can only enhance riding safety if the riders use them. For this reason, acceptance is a decisive aspect to be considered in the development process of such systems. In order to be able to improve behavioural acceptance, the factors that influence the intention to use the system need to be identified. This paper examines the particularities of motorcycle riding and the characteristics of this user group that should be considered when predicting the acceptance of advanced rider assistance systems. Founded on theories predicting behavioural intention, the acceptance of technologies and the acceptance of driver support systems, a model on the acceptance of advanced rider assistance systems is proposed, including the perceived safety when riding without support, the interface design and the social norm as determinants of the usage intention. Since actual usage cannot be measured in the development stage of the systems, the willingness to have the system installed on the own motorcycle and the willingness to pay for the system are analyzed, constituting relevant conditions that allow for actual usage at a later stage. Its validation with the results from user tests on four advanced rider assistance systems allows confirming the social norm and the interface design as powerful predictors of the acceptance of ARAS, while the extent of perceived safety when riding without support did not have any predictive value in the present study.
The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx. However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My. The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was observed. It was also observed that the primary neck response in these tests was flexion, not extension. This correlates well with recent findings from Japan and the United States showing a correlation between neck flexion and injury in accident replication simulations and postmortem human subjects (PMHS) studies, respectively. The present certification tests may not adequately control front cervical spine bumper characteristics, which are important for neck flexion response. The certification sled test also does not include the pelvis and so cannot be used to control pelvis response and does not substantially load the lumbar bumpers and so does not control these parts of the dummy. The stiffness of all spine bumpers and of the pelvis flesh should be much more tightly controlled. It is recommended that a method for certifying the front cervical bumpers should be developed. Recommendations are also made for tighter tolerance on the input parameters for the existing certification tests.
Das Ziel der Untersuchung war, die Grenzen der Belastbarkeit eines Rollstuhl- und Personenrückhaltesystems mit Kraftknoten nach DIN 75078-2 zu ermitteln. Dazu wurden dynamische Schlittenversuche durchgeführt, bei denen die Verzögerungspulse sowie das Gesamtgewicht von Rollstuhl und Prüfpuppe variiert wurden. Für die Untersuchungen kamen ein Prüfrollstuhl, definiert nach ISO 10542, und Rückhaltesysteme mit Kraftknoten gemäß DIN 75078-2 zum Einsatz. Das Rückhaltesystem bestand aus einem Rollstuhl- und einem Personenrückhaltesystem, wobei das Rollstuhlrückhaltesystem (RRS) mit vier bzw. sechs Gurten und entsprechenden Retraktoren an einem dynamischen Schlittenaufbau befestigt wurde. Das Personenrückhaltesystem (PRS) bestand aus einem am Rollstuhl integrierten Beckengurt sowie einem Schulterschräggurt, der am Beckengurt und am Schlittenaufbau befestigt wurde. Ferner wurden bei den Versuchen Prüfpuppen verschiedener Alters- und Gewichtsklassen (P6, HIII 5 %, HIII 50 % und HIII 95 %) eingesetzt Die Belastungsanforderungen für das Rückhaltesystem wurden sukzessiv erweitert, indem einerseits das Gesamtgewicht (Rollstuhl und Prüfpuppe) und andererseits auch die Verzögerungspulse bis zur Versagensgrenze erhöht wurden. Das Vier-Gurt-Rückhaltesystem konnte bei einem Verzögerungspuls von 10 g einem Gesamtgewicht von bis zu 221 kg standhalten. Bei einem Verzögerungspuls von 20 g und einem Gesamtgewicht von 134 kg wurde das Vier-Gurt-System bis über die Grenzen belastet. Das Sechs-Gurt-Rückhaltesystem hat Belastungen bis 221 kg standgehalten. Infolgedessen ist bei einer Erhöhung der Verzögerungspulse auf 20 g und einem Gesamtgewicht von mehr als 109 kg ein Sechs-Gurt-System zu empfehlen.
In general the passive safety capability is much greater in newer versus older cars due to the stiff compartment preventing intrusion in severe collisions. However, the stiffer structure which increases the deceleration can lead to a change in injury patterns. In order to analyse possible injury mechanisms for thoracic and lumbar spine injuries, data from the German Inâ€Depth Accident Study (GIDAS) were used in this study. A twoâ€step approach of statistical and caseâ€byâ€case analysis was applied for this investigation. In total 4,289 collisions were selected involving 8,844 vehicles, 5,765 injured persons and 9,468 coded injuries. Thoracic and lumbar spine injuries such as burst, compression or dislocation fractures as well as soft tissue injuries were found to occur in frontal impacts even without intrusion to the passenger compartment. If a MAIS 2+ injury occurred, in 15% of the cases a thoracic and/or lumbar spine injury is included. Considering AIS 2+ thoracic and lumbar spine, most injuries were fractures and occurred in the lumbar spine area. From the case by case analyses it can be concluded that lumbar spine fractures occur in accidents without the engagement of longitudinals, lateral loading to the occupant and/or very severe accidents with MAIS being much higher than the spine AIS.
Die UNECE Regelung R58 regelt die Beschaffenheit und die Installation von Heckunterfahrschutzsystemen an schweren Güterkraftfahrzeugen, deren Ziel die Verbesserung der Kompabilität zwischen Pkw-Frontstrukturen und Lkw-Hecks ist. Dennoch verunglücken laut amtlicher Unfallstatistik allein in Deutschland rund 30 Pkw-Insassen in Heckauffahrunfällen auf Lkw tödlich, da diese Vorrichtungen hinsichtlich Einbauhöhe und Steifigkeit den Anforderungen des realen Unfallgeschehens nicht genügen. Das Ziel dieser Studie ist eine quantitative Abschätzung der möglichen Reduzierung der Verletzungsschwere mit Hilfe eines statistischen Modells, die durch eine Anpassung der geltenden Bestimmungen und die damit verbundenen technischen Veränderungen des bereits vorgeschriebenen Heckunterfahrschutzes zu erreichen wäre. In einer Nutzen-Kosten-Analyse wird die Wirtschaftlichkeit dieser Modifizierungen mit einem idealen Notbremsassistenten verglichen. Die Untersuchung orientiert sich dabei an den aktuell in der UN-ECE WP29/GRSG in Genf diskutierten Vorschlägen zur Anpassung der ECE-R58. Das verwendete ordinale Probit-Modell stellt einen Zusammenhang zwischen der Verletzungsschwere im auffahrenden PKW und erklärenden Größen her, in diesem Fall der kinetischen Energie des unterfahrenden Pkws und der strukturellen lnteraktion zwischen Lkw-Heck und Pkw-Front. Diese Maßnahmen könnten demnach 53 - 78% der Getöteten sowie 27 - 49% der Schwerverletzten bei diesen Unfallkonstellationen reduzieren, was pro Jahr 20 Getöteten und 95 Schwerverletzten entsprechen würde. Somit würde eine Modifikation einer bestehenden passiven Schutzmaßnahme an jährlich 100.000 neuzugelassenen Lkw und Anhängern bereits 20 Getötete adressieren. Im Vergleich dazu müssten jährlich 3 Millionen Pkw mit zusätzlicher Sensorik und Aktuatorik für einen idealen Notbremsassistenten ausgestattet werden, um im Idealfall alle Heckauffahrunfälle von Pkw auf andere Pkw oder Lkw und damit 53 Getötete zu vermeiden. Daher fällt auch das Nutzen-Kosten-Verhältnis deutlich zugunsten des verbesserten Heckunterfahrschutzes aus.
It is commonly agreed that active safety will have a significant impact on reducing accident figures for pedestrians and probably also bicyclists. However, chances and limitations for active safety systems have only been derived based on accident data and the current state of the art, based on proprietary simulation models. The objective of this article is to investigate these chances and limitations by developing an open simulation model. This article introduces a simulation model, incorporating accident kinematics, driving dynamics, driver reaction times, pedestrian dynamics, performance parameters of different autonomous emergency braking (AEB) generations, as well as legal and logical limitations. The level of detail for available pedestrian accident data is limited. Relevant variables, especially timing of the pedestrian appearance and the pedestrian's moving speed, are estimated using assumptions. The model in this article uses the fact that a pedestrian and a vehicle in an accident must have been in the same spot at the same time and defines the impact position as a relevant accident parameter, which is usually available from accident data. The calculations done within the model identify the possible timing available for braking by an AEB system as well as the possible speed reduction for different accident scenarios as well as for different system configurations. The simulation model identifies the lateral impact position of the pedestrian as a significant parameter for system performance, and the system layout is designed to brake when the accident becomes unavoidable by the vehicle driver. Scenarios with a pedestrian running from behind an obstruction are the most demanding scenarios and will very likely never be avoidable for all vehicle speeds due to physical limits. Scenarios with an unobstructed person walking will very likely be treatable for a wide speed range for next generation AEB systems.
Regarding to the German road traffic licensing regulations it is mandatory to have a light system using a bicycle in public traffic. All attached components must be approved. The admission requires additional restrictions such as a dynamo as energy source with a nominal voltage of 6 V. Batteries are only allowed in addition to this. To adopt the German bicycle regulation to the state of art of an energy efficient lighting, additional power sources such as a battery respectively rechargeable batterie should be evaluated. The project will propose amendments for German Road Traffic Regulations and technical requirements.
Airbag-Systeme können, wie frühere Untersuchungen gezeigt haben, die passive Sicherheit von Motorrädern wirksam verbessern. Der vorliegende Forschungsbericht betrachtet die Übertragbarkeit von Pkw-Airbag-Konzepten auf das Motorrad und befasst sich vor allem mit dem Problem der motorradgerechten und sicheren Auslösung des Airbags. Die Funktion des Motorradairbags unterscheidet sich von der des Pkw-Airbags in entscheidender Weise durch die Möglichkeit, die Flugbahn des Fahrers bei einem Zusammenstoß mit einem rechtwinklig vor dem Motorrad befindlichen Pkw so zu beeinflussen, dass dieser das Hindernis ohne einen harten Anprall überfliegen kann. Der Abbau der kinetischen Energie des Fahrers geschieht so nicht in der kurzen Knautschzone vor dem Kollisionsobjekt, sondern in der meist ausreichend langen Auslaufzone dahinter. Der Motorradairbag kann am vorderen Tankbereich angebracht sein. Fülltechnik und Gewebematerial können vom Pkw direkt übernommen werden; jedoch ist die Nahtführung zu verstärken, da der Motorradairbag vorwiegend auf Scherung beansprucht wird. Gravierende Unterschiede ergeben sich in der Sensierung eines Crashs, da durch das an der Telegabel geführte Vorderrad signifikante Verzögerungsanstiege des Motorrades erst sehr spät erfolgen. Es ist daher nicht möglich, wie beim Pkw den Airbag allein über Beschleunigungsaufnehmer zu zünden. Schwerpunkt des Berichtes sind daher verschiedene Vorschläge, bei heute üblichen Motorradkonstruktionen einen Crash für eine Airbagauslösung rechtzeitig und sicher sensieren zu können. Zu charakteristischen Unfall-Ereignissen werden Sensoren nach verschiedenen Wirkprinzipien geordnet vorgestellt. Nach einer technischen Bewertung erweisen sich zwei Sensorvarianten als geeignet für eine zuverlässige Zündung des Airbag; gleichzeitig kann mit einer logischen Verknüpfung ihrer Signale eine Fehlauslösung sicher vermieden werden. Die ausgewählten und näher beschriebenen Sensoren registrieren den Druckanstieg im Vorderradreifen und die plastische Verformung der Telegabel. Damit ist eine Sensierung des Aufpralls rechtzeitig möglich. Je nach Größe und Dauer der Verzögerung kann der Druck des Luftkissens verändert werden, so dass der Motorradairbag in Abhängigkeit der Fahrgeschwindigkeit nur aufpralldämpfend oder flugbahnbeeinflussend wirkt. Testprogramme zur weiteren Entwicklung von Airbagsensoren für Motorräder werden als Forschungsbedarf näher erläutert.
Teil 1 des vorliegenden Berichts nimmt zur Frage nach den Erfahrungen mit der (unbewehrten) Helmtragepflicht für Moped/Mokick-Benutzer Stellung. Dabei zeigen die Daten der amtlichen Straßenverkehrsunfallstatistik eine Verbesserung der Verletzungsschwerestruktur, dies allerdings auch schon in den Jahren der Erweiterung der Helmtragepflicht. In Teil 2 wird über das Helmtrageverhalten nach Einführung des Verwarnungsgeldes berichtet. Hier zeigte sich eine deutliche Verbesserung. In Teil 3 schließlich wird die Frage untersucht, ob sich aus der amtlichen Straßenverkehrsunfallstatistik eine überproportionale Beteiligung der jugendlichen Mofabenutzer am Unfallgeschehen nachweisen lässt. In den Jahren 1977 bis 1979 verunglückten insgesamt 87556 Mofabenutzer. Mehr als die Hälfte der Verunglückten war jünger als 18 Jahre; fast zwei Drittel war jünger als 21 Jahre. Nur knapp ein Viertel war 35 Jahre und älter.
Stellungnahme zu einer Ausdehnung der Schutzhelmtragepflicht auf Moped/Mokick- und Mofabenutzer
(1977)
Im Hinblick auf die Unfallentwicklung bei motorisierten Zweiradfahrern wurde eine Untersuchung zur Ausdehnung der Verpflichtung, einen Schutzhelm zu tragen, auf Moped/Mokick- und Mofafahrer durchgeführt. Die Unfallschwere bei Außerortsunfällen ist hervorzuheben. Dabei handelt es sich überwiegend um Kopfverletzungen. Die Schutzwirkung von Helmen wird generell positiv eingeschätzt. Auf 1976 bezogen hätten bei Helmtragepflicht und 100 % Tragequote vermutlich rund 140 Tote, 2200 Schwerverletzte und 4400 Leichtverletzte eingespart werden können. Es wird empfohlen, die Helmtragepflicht zwingend vorzuschreiben. Nach den bisherigen Erfahrungen würde die Helmtragepflicht ohne Bußgeldbewehrung nicht auf die optimale Größenordnung angehoben werden können. Schutzhelme für motorisierte Zweiradfahrer sollten mindestens der DIN 4848 (1970) "Kraftfahrer-Schutzhelme" entsprechen, auch wenn die DIN 4848 noch nicht voll alle Forderungen an Schutzhelme abdeckt. Die Helmtragepflicht sollte so schnell wie möglich eingeführt werden. Die Einführung der Helmtragepflicht ist besonders auch unter gesamtwirtschaftlichen Gesichtspunkten sinnvoll.
Zur Unterstützung von Forschungsvorhaben auf dem Gebiet der Belastung und Beanspruchung von Kraftfahrern hat die Bundesanstalt für Straßenwesen ein Versuchsfahrzeug, genannt Fahrerleistungsmessfahrzeug (FLMF), sowie die dazugehörigen Nebeneinrichtungen erstellen lassen. Mit diesem Fahrzeug wurde eine erste, psychologisch orientierte Erprobungsstudie im realen Straßenverkehr durchgeführt, um problemorientierte Erfahrungen sammeln zu können. Zur inhaltlichen Ausrichtung der Untersuchung wurde ein Modell über Bedingungen des Kraftfahrerverhaltens im Straßenverkehr entwickelt. In diesem Grundmodell werden situative und situationsübergreifende Komponenten unterschieden, die jeweils personen- und verkehrsbezogen ausgeprägt sein können. In der durchgeführten Untersuchung wird das Schwergewicht auf die Analyse der situationsübergreifenden personenbezogenen Bedingungen gelegt. Die unterschiedlichen situativen verkehrsbezogenen Bedingungen dienen hauptsächlich der Beschreibung der Anforderungen an den Kraftfahrer. Mit 27 Versuchspersonen wurden im Kölner Innenstadtbereich Versuchsfahrten durchgeführt. Die Fahrertätigkeit, wie z.B. Gas geben, Lenken, Bremsen wurden kontinuierlich automatisch erfasst. Zugleich konnten Befragungsergebnisse über Tasten elektronisch gespeichert werden. Auf wichtigen Versuchsabschnitten zeichnete eine Video-Anlage das Verkehrsgeschehen auf. In einer Serie von Vergleichen ausgewählter Situationen werden die situativen und situationsübergreifenden Einflüsse verdeutlicht. Die Ergebnisse zeigen bzw. bestätigen, dass im Innenstadtbereich der situative Einfluss auf das Kraftfahrerverhalten größer ist als der situationsübergreifende.
Erkenntnisse über den Nutzen zusätzlicher hochgesetzter Bremsleuchten sind lückenhaft und zum Teil widersprüchlich. Im Rahmen einer Untersuchung über den Einfluss zusätzlicher Bremsleuchten auf das Unfallgeschehen wurden u.a. folgende Fragen behandelt: 1. Entwicklung der Unfälle durch Auffahren auf Fahrzeuge, die mit zusätzlichen Bremsleuchten ausgerüstet sind, 2. Entwicklung der Auffahrunfälle insgesamt, 3. Verletzungen von Fahrzeuginsassen durch Leuchten, 4. Auswirkungen auf die übrigen Verkehrsteilnehmer (Abstand, Blendung, Fehlreaktion). Anhand konkreter Daten über das Unfallgeschehen in Bayern und Niedersachsen kommt der Beitrag insgesamt zu dem Urteil, dass die derzeitige Regelung weder durch eine Einbauvorschrift noch durch ein Einbauverbot hochgesetzter Bremsleuchten ersetzt werden müsste.
Ziel der Untersuchung war es, das Fahrverhalten unter Akutmedikation von Diphenhydramin im Daimler-Benz Fahrsimulator zu untersuchen. Dazu wurden 60 männliche Studenten auf drei Gruppen verteilt; von ihnen erhielt eine Gruppe eine mittlere Dosis von 0,71 mg/kg, eine Gruppe eine hohe Dosis von 1,07 mg/kg und eine Kontrollgruppe kein Medikament. Die 20-minütige Testfahrt im Fahrsimulator setzte sich aus zehn unterschiedlichen Szenarien zusammen, die zum Teil Überraschungseffekte mit hohen Anforderungen an die Probanden beinhalteten. Wegen der sicheren Lerneffekte war eine wiederholte Simulatorfahrt mit den gleichen Probanden unter verschiedenen Medikamentendosen beziehungsweise als Kontrollgruppe nicht möglich. Vor und nach der Simulatorfahrt wurde der Wirkstoffgehalt des Diphenhydramins im Serum festgestellt. Die subjektive Befindlichkeit wurde im Laufe des Testtages zweimal abgefragt. Außerdem wurden im Anschluss an die Simulatorfahrt psychometrische Leistungstests durchgeführt. Signifikante Unterschiede zwischen den drei Gruppen fanden sich in den betrachteten Variablen in keinem der zehn Szenarien oder den drei psychometrischen Leistungstests. Die individuellen Unterschiede innerhalb der Gruppen waren stets größer als die Unterschiede zwischen den Gruppen. In der Basler Befindlichkeits-Skala fanden sich in wenigen Variablen signifikante Unterschiede. Die Ergebnisse führten zu der Hypothese, dass die Fahrtüchtigkeit nicht direkt und nicht allein von der Dosierung des Diyphenhydramins abhängig ist, vielmehr kann in bestimmten Dosisbereichen eine Kompensation eintreten.
Vor dem Hintergrund der derzeitigen Verkehrs- und Unfallsituation sowie verkehrsrechtlicher Vorschriften wurde durch Auswertung humanwissenschaftlicher und technischer Literatur eine Sachstandsbeschreibung erstellt, die die in Zusammenhang mit Auffahrunfällen und ihrer Verhinderung stehenden Aspekte aufzeigt. Als fahrzeugtechnische Hilfen zur Einhaltung eines ausreichenden Abstandes zwischen hintereinander fahrenden Fahrzeugen werden dabei vorrangig autarke Systeme - das sind solche, bei denen sich alle notwendigen Vorrichtungen im Fahrzeug befinden - betrachtet. Möglichkeiten und Grenzen der bekannten technischen Hilfsmittel, insbesondere der Abstandswarn- und Abstandsregelungseinrichtungen werden aufgezeigt. Es stellte sich heraus, dass den Warnstrategien sowie ihren Auswirkungen auf den Verkehrsablauf und die Verkehrssicherheit besondere Bedeutung zukommt. In diesem Zusammenhang werden auch Zielkonflikte, insbesondere zwischen Sicherheitsforderungen und Fahrerakzeptanz, deutlich. Im Teil I des Berichts erfolgt die zusammenfassende Beschreibung und kritische Wertung des Sachstandes. Im Teil II werden die Auswerteergebnisse zu den angesprochenen Fragenkomplexen im einzelnen dargestellt. Teil III enthält eine Kurzdokumentation der für die Erstellung des Berichts wesentlichsten Literaturstellen.
Es wurden Versuchsreihen mit Trageeinrichtungen von Motorrad- und Fahrradhelmen durchgeführt. Trageeinrichtungen sollen bei einem Unfall verhindern, dass es zu einem Verlust des Helms kommt. Zur Prüfung der Belastbarkeit von Trageeinrichtungen wurde ein Prüfstand entwickelt und aufgebaut, mit dem die Kraft, der ein Tragesystem standhalten kann, bestimmt werden kann. Die Ergebnisse belegen, dass Tragesysteme von Motorradhelmen Kräften widerstehen können, die fast dreimal so hoch sind, wie die unter Standardbedingungen der ECE-R 22 aufgebrachten. Vier der fünf getesteten Fahrradhelme widerstanden höheren Kräften als im Normentwurf gefordert.
Es wird auf die neueste Auflage des Gutachtens Krankheit und Kraftverkehr, Bonn 1995, eingegangen. Insbesondere dessen Auswirkungen für körperbehinderte Autofahrer wird beschrieben. Es wird dabei genau auf den Umfang beziehungsweise das Ausmaß der Behinderung und deren Auswirkung auf die Fahrtauglichkeit eingegangen.
Bestimmte Fragestellungen der Verkehrssicherheitsarbeit und der Unfallforschung, speziell solche zu neuen Informationstechnologien im Fahrzeug, lassen sich nur mit Fahrproben beantworten. In dem Bericht sind bisherige Erfahrungen zusammengestellt, die bei der Durchführung von Fahrproben gemacht wurden. Im einzelnen werden Verfahrensvorschläge für folgende Problembereiche erörtert: Einflussfelder, Untersuchungsinstrumente und Entwicklung von Fahrversuchen; Operationalisierung der Fragestellung; Fahrraumdefinitionen (Fahrraum und Umfeld); Verknüpfung von Situation und Fahrraumumfeld; Grundlagen und Festlegung der statistischen Prüfmethoden; Anforderungen an die Messstrecke, das Messfahrzeug und die Auswerteeinheit; Versuchsdesign und statistische Sicherheitswahrscheinlichkeit; Versuchspersonenauswahl; Homogenisierung der Versuchspersonenstichprobe; Effektstärken; Stichprobengröße; Datenerhebung; Datenstrukturierung; Auswertung sowie Dokumentation. Es handelt sich nicht um ein in sich geschlossenes Methodenbuch, sondern um einen Methodenaufriss einschließlich Literaturangaben.
Die Untersuchung sollte erörtern, ob es empfehlenswert ist, das Testverfahren zum streifenden Anprall eines Motorradhelmes auf die Straßenoberfläche in die ECE-R 22 aufzunehmen. Dazu war zu klären, ob die Testmethode geeignet ist, rotatorische Kräfte auf den Prüfkopf zu erfassen und ob sich aufgrund der Unfallsituationen eine Notwendigkeit für ein solches Testverfahren ergibt. Die Messergebnisse zeigen, dass der Zusammenhang zwischen der verletzungswirksamen Rotationsbeschleunigung und der im Testverfahren gemessenen Tangentialkraft nicht ohne Zweifel belegbar ist. Somit wäre zu fordern, dass statt der Tangentialkraft die Rotationsbeschleunigung als Verletzungskriterium betrachtet wird. Dafür wird jedoch ein sehr hoher Anspruch an die Messtechnik im Labor gestellt. Aus der Sicht der Unfallforschung lässt sich sagen, dass bei derartigen Anprallsituationen, insbesondere bei Anprallgeschwindigkeiten von unter 40 km/h, die sich im Laborversuch realisieren lassen, nur mäßige Kopfverletzungen auftreten (AIS 2 oder geringer). Der hohe Aufwand des Testverfahrens scheint also nicht gerechtfertigt zu sein.
Beschrieben wird die Evaluierung eines Testverfahrens der Arbeitsgruppe 10 des European Experimental Vehicle Committee, mit dem die "Fußgängerverträglichkeit" von Frontflächen von Personenkraftwagen bestimmt werden kann. Dabei werden verschiedene Anprallarten von Fußgängern an Fahrzeugen simuliert: der Anprall eines Beines an den Stoßfänger, der Anprall des Oberschenkels an die Vorderkante der Fronthaube und der Anprall des Kopfes auf die Fronthaube. Im Beitrag wird auf die Durchführung von Tests zum Oberschenkelanprall und zum Beinanprall an drei verschiedenen Fahrzeugtypen eingegangen. Beschrieben werden Testverfahren, Versuchsaufbau und Versuchsdurchführung. Die Versuchsreihe zeigte, dass das entwickelte Testverfahren praktikabel ist.
EEVC Status report
(2001)
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
Der Autor berichtet über zwei Forschungsprojekte zur Prüfung von runderneuerten Reifen durch Schnell- und Dauerlaufprüfung. Es wurden Pkw- und Lkw-Reifen mit Karkassen unterschiedlicher Hersteller und unterschiedlichen Alters mit und ohne reparierte Durchstoßschäden untersucht. Die Versuchsergebnisse spechen für eine Altersbegrenzung der rundzuerneuernden Karkassen auf 6 Jahre. Das Reparieren sollte nur bei der Runderneuerung von Lkw-Reifen toleriert werden. Eine Rückstufung der Geschwindigkeitsklassen nach Runderneuerung von Pkw-Reifen zeigt eine positive Wirkung.
A means of assessing the passive safety of automobiles is a desirable instrument for legislative bodies, the automobile industry, and the consumer. As opposed to the dominating motor vehicle assessment criteria, such as engine power, spaciousness, aerodynamics and consumption, there are no clear and generally accepted criteria for assessing the passive safety of cars. The proposed method of assessment combines the results of experimental safety tests, carried out according to existing legally prescribed or currently discussed testing conditions, and a biomechanical validation of the loading values determined in the test. This evaluation is carried out with the aid of risk functions which are specified for individual parts of the body by correlating the results of accident analysis with those obtained by computer simulation. The degree of conformance to the respective protection criterion thus deduced is then weighted with factors which take into account the frequency of occurrence and the severity of the accident on the basis of resulting costs. Each of the test series includes at least two frontal and one lateral crash test against a deformable barrier. The computer-aided analysis and evaluation of the simulation results enables a vehicle-specific overall safety index as well as partial and individual safety values to be determined and plotted graphically. The passive safety provided by the respective vehicle under test can be defined for specific seating positions, special types of accident, or for individual endangered parts of the body.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
Berichtet wird über eine Neufassung des Handbuches zur bürgerfreundlichen und behindertengerechten Gestaltung des Straßenraumes. Ziel dieses Handbuches ist es, die aktuellen nationalen und internationalen Regelungen und Empfehlungen, Normungen und Untersuchungen zu erfassen und für eine behindertengerechte Straßenraumplanung, die für viele behinderte und ältere Menschen erst die Möglichkeit zur Mobilität schafft, nutzbar zu machen.