Abteilung Fahrzeugtechnik
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (106) (entfernen)
Schlagworte
- Anfahrversuch (37)
- Safety (35)
- Impact test (veh) (34)
- Sicherheit (34)
- Bewertung (30)
- Conference (29)
- Evaluation (assessment) (29)
- Konferenz (29)
- Fahrzeug (26)
- Test method (25)
Institut
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
A series of drop tests and vehicle tests with the adult head impactor according to Regulation (EC) 631/2009 and drop tests with the phantom head impactor according to UN Regulation No. 43 have been carried out by the German Federal Highway Research Institute (BASt) on behalf of the German Federal Ministry of Transport, Building and Urban Development (BMVBS). Aim of the test series was to study the injury risk for vulnerable road users, especially pedestrians, in case of being impacted by a motor vehicle in a way described within the European Regulations (EC) 78/2009 and (EC) 631/2009. Furthermore, the applicability of the phantom head drop test described in UN Regulation No. 43 for plastic glazing should be investigated. In total, 30 drop tests, thereof 18 with the adult head impactor and 12 with the phantom head impactor, and 49 vehicle tests with the adult head impactor were carried out on panes of laminated safety glass (VSG), polycarbonate (PC) and laminated polycarbonate (L-PC). The influence of parameters such as the particular material properties, test point locations, fixations, ambient conditions (temperature and impact angle) was investigated in detail. In general, higher values of the Head Injury Criterion (HIC) were observed in tests on polycarbonate glazing. As the HIC is the current criterion for the assessment of head injury risk, polycarbonate glazing has to be seen as more injurious in terms of vulnerable road user protection. In addition, the significantly higher rebound of the head observed in tests with polycarbonate glazing is suspected to lead to higher neck loads and may also cause higher injury risks in secondary impacts of vulnerable road users. However, as in all tests with PC glazing no damage of the panes was observed, the risk of skin cut injuries may be expected to be reduced significantly. The performed test series give no indication for the test procedure prescribed in UN Regulation No. 43 as a methodology to approve glass windscreen not being feasible for polycarbonate glazing, as all PC panes tested fulfilled the UN R 43 requirements. The performance of the windscreen area will not be relevant for vehicle type approval according to the upcoming UN Regulation for pedestrian protection. However, it is recommended that pedestrian protection being considered for plastic windscreens to ensure at least the same level of protection as glass windscreens.
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
The off-set assessment procedure potentially contributes to the FIMCAR objectives to maintain the compartment strength and to assess load spreading in frontal collisions. Furthermore it provides the opportunity to assess the restraint system performance with different pulses if combined with a full-width assessment procedure in the frontal assessment approach. Originally it was expected that the PDB assessment procedure would be selected for the FIMCAR assessment approach. However, it was not possible to deliver a compatibility metric in time so that the current off-set procedure (ODB as used in UNECE R94) with some minor modifications was proposed for the FIMCAR Assessment Approach. Nevertheless the potential to assess load spreading, which appears not to be possible with any other assessed frontal impact assessment procedure was considered to be still high. Therefore the development work for the PDB assessment procedure did not stop with the decision not to select the PDB procedure. As a result of the decisions to use the current ODB and to further develop the PDB procedure, both are covered within this deliverable. The deliverable describes the off-set test procedure that will be recommended by FIMCAR consortium, this corresponds to the ODB test as it is specified in UN-ECE Regulation 94 (R94), i.e. EEVC deformable element with 40% overlap at a test speed of 56 km/h. In addition to the current R94 requirements, FIMCAR will recommend to introduce some structural requirements which will guarantee sufficiently strong occupant compartments by enforcing the stability of the forward occupant cell. With respect to the PDB assessment procedure a new metric, Digital Derivative in Y direction - DDY, was developed, described, analysed, and compared with other metrics. The DDY metric analyses the deformation gradients laterally across the PDB face. The more even the deformation, the lower the DDY values and the better the metric- result. In order analyse the different metrics, analysis of the existing PDB test results and the results of the performed simulation studies was performed. In addition, an assessment of artificial deformation profiles with the metrics took place. This analysis shows that there are still issues with the DDY metric but it appears that it is possible to solve them with future optimisations. For example the current metric assesses only the area within 60% of the half vehicle width. For vehicles that have the longitudinals further outboard, the metric is not effective. In addition to the metric development, practical issues of the PDB tests such as the definition of a scan procedure for the analysis of the deformation pattern including the validation of the scanning procedure by the analysis of 3 different scans at different locations of the same barrier were addressed. Furthermore the repeatability and reproducibility of the PDB was analysed. The barrier deformation readings seem to be sensitive with respect to the impact accuracy. In total, the deliverable is meant to define the FIMCAR off-set assessment procedure and to be a starting point for further development of the PDB assessment procedure.
The objective of this deliverable is to describe the expected influence of the candidate test procedures developed in FIMCAR for frontal impact on other impact types. The other impact types of primary interest are front-to-side impacts, collisions with road restraint systems (e.g. guardrails), and heavy goods vehicle impacts. These collision types were chosen as they involve structures that can be adapted to improve safety. Collisions with vulnerable road users (VRU) were not explicitly investigated in FIMCAR. It is expected that the vehicle structures of interest in FIMCAR can be designed into a VRU friendly shell. Information used for this deliverable comes from simulations and car-to-car crash tests conducted in FIMCAR or review of previous research. Three test configurations (full width, offset, and moving deformable barriers) were the input to the FIMCAR selection process. There are three different types of offset tests and two different full width tests. During the project test procedures could be divided into three groups that provide different influences or outcomes on vehicle designs: 1. The ODB barrier provides a method to assess part of the vehicles energy absorption capabilities and compartment test in one test. 2. The FWRB and FWDB have similar capabilities to control structural alignment, further assess energy absorption capabilities, and promote the improvements in the occupant restraint system for high deceleration impacts. 3. The PDB and MPDB can be used to promote better load spreading in the vehicle structures, in addition to assessing energy absorption and occupant compartment strength in an offset configuration. The consortium selected the ODB and FWDB as the two best candidates for short term application in international rulemaking. The review of how all candidates would affect vehicle performance in other impacts (beside front-to-front vehicle or frontal impacts with fixed obstacles) however is reported in this deliverable to support the benefit analysis reported in FIMCAR. The grouping presented above is used to discuss all five test candidates using similarities between certain tests and thereby simplify the discussion.
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for over 10 years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in current research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The objectives of the work reported in this deliverable were to review existing full-width test procedures and their discussed compatibility metrics, to report recent activities and findings with respect to full-width assessment procedures and to assess test procedures and metrics. Starting with a review of previous work, candidate metrics and associated performance limits to assess a vehicle- structural interaction potential, in particular its structural alignment, have been developed for both the Full Width Deformable Barrier (FWDB) and Full Width Rigid Barrier (FWRB) tests. Initial work was performed to develop a concept to assess a vehicle- frontal force matching. However, based on the accident analyses performed within FIMCAR frontal force matching was not evaluated as a first priority and thus in line with FIMCAR strategy the focus was put on the development of metrics for the assessment of structural interaction which was evaluated as a first priority.
Accident analysis
(2014)
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the EC funded FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in today- research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The specific objectives of the work reported in this deliverable were: - Determine if previously identified compatibility issues are still relevant in current vehicle fleet: Structural interaction, Frontal force matching, Compartment strength in particular for light cars. - Determine nature of injuries and injury mechanisms: Body regions injured o Injury mechanism: Contact with intrusion, Contact, Deceleration / restraint induced. The main data sources for this report were the CCIS and Stats 19 databases from Great Britain and the GIDAS database from Germany. The different sampling and reporting schemes for the detailed databases (CCIS & GIDAS) sometimes do not allow for direct comparisons of the results. However the databases are complementary " CCIS captures more severe collisions highlighting structure and injury issues while GIDAS provides detailed data for a broader range of crash severities. The following results represent the critical points for further development of test procedures in FIMCAR.
Cost benefit analysis
(2014)
Although the number of road accident casualties in Europe is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities [EC 2012]. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car- safety performance in frontal impacts is to improve its compatibility for car-to-car impacts and for collisions against objects and HGVs. Compatibility consists of improving both a car- self and partner protection in a manner such that there is good interaction with the collision partner and the impact energy is absorbed in the car- frontal structures in a controlled way which results in a reduction of injuries. Over the last ten years much research has been performed which has found that there are four main factors related to a car- compatibility [Edwards 2003, Edwards 2007]. These are structural interaction potential, frontal force matching, compartment strength and the compartment deceleration pulse and related restraint system performance. The objective of the FIMCAR FP7 EC-project was to develop an assessment approach suitable for regulatory application to control a car- frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation.
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for over 10 years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and the final report to the steering committee on frontal impact [Faerber 2007] and the FP5 VC-COMPAT[Edwards 2007] project activities, two test approaches were identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in current research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis will be performed. In the FIMCAR Deliverable D 3.1 [Adolph 2013] the development and assessment of criteria and associated performance limits for the full width test procedure were reported. In this Deliverable D3.2 analyses of the test data (full width tests, car-to-car tests and component tests), further development and validation of the full width assessment protocol and development of the load cell and load cell wall specification are reported. The FIMCAR full-width assessment procedure consists of a 50 km/h test against the Full Width Deformable Barrier (FWDB). The Load Cell Wall behind the deformable element assesses whether or not important Energy Absorbing Structures are within the Common Interaction Zone as defined based on the US part 581 zone. The metric evaluates the row forces and requires that the forces directly above and below the centre line of the Common Interaction Zone exceed a minimum threshold. Analysis of the load spreading showed that metrics that rely on sum forces of rows and columns are within acceptable tolerances. Furthermore it was concluded that the Repeatability and Reproducibility of the FWDB test is acceptable. The FWDB test was shown to be capable to detect lower load paths that are beneficial in car-to-car impacts.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
This paper presents findings of a laboratory experiment which aimed at evaluating the sensitivity and intrusiveness of Tactile Detection Response Task (TDRT) methodology. Various single-task, dual-task and triple-task scenarios were compared. The task scenarios included a surrogate of driving (tracking task) and different secondary tasks (N-back, surrogate reference task (SuRT)). The results suggest that the TDRT is sensitive to load levels of secondary tasks which primarily demand for cognitive resources (N-back). Sensitivity to variations of visual"manual load could not be shown (SuRT). TDRT seems also to be able to differentiate between modes of primary task which varies in terms of cognitive load (visual against auditory tracking task). Results indicated intrusiveness of TDRT on primary task performance and secondary task performance depending on the type of underlying task scenario. As a conclusion, TDRT can be recommended as a method to assess attentional effects of cognitive load of a secondary task, but should be used with caution for secondary tasks with strong motor demands.
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
Established in 1997, the European New Car Assessment Programme (Euro NCAP) provides consumers with a safety performance assessment for the majority of the most popular cars in Europe. Thanks to its rigorous crash tests, Euro NCAP has rapidly become an important driver safety improvement to new cars. After ten years of rating vehicles, Euro NCAP felt that a change was necessary to stay in tune with rapidly emerging driver assistance and crash avoidance systems and to respond to shifting priorities in road safety. A new overall rating system was introduced that combines the most important aspects of vehicle safety under a single star rating. The overall rating system has allowed Euro NCAP to continue to push for better fitment and higher performance for vehicles sold on the European market. In the coming years, the safety rating is expected to play an important role in the support of the roll-out of highly automated vehicles.
Estimation of the effects of new emission standards on motorcycle emissions by means of modeling
(2016)
Road traffic is, in addition to the energy sector and the industry, one main source of air pollution and carbon dioxide emissions. Although most countries and manufacturers agreed to environmental regulations to reduce the pollutant emissions, particularly in urban areas with high traffic density, the impact of road traffic emissions on the environment and human health has been growing in importance steadily. Due to stricter emission standards and the binding use of emission-reducing systems (e.g. three-way catalyst) hydrocarbon emissions from passenger cars have been reduced significantly since the last two decades. Unlike to passenger cars the emissions standards of powered two-wheelers have not been adjusted since 2006 although their share of hydrocarbon emissions to the total amount of hydrocarbon emissions of road traffic is estimated to be disproportionately high. Due to the new regulation (EU) No. 168/2013 powered two-wheelers have to fulfill new emission standards from 2016 (Euro 4) and 2020 (Euro 5) onwards. Besides new limits for the tailpipe emissions the evaporative emissions are regulated separately for the first time, as they make up a high proportion to the total hydrocarbon emissions in this vehicle class. In this context, the calculation and forecast of road traffic emissions is an important tool to verify compliance of climate targets and to assess the reduction potential of emission-reducing systems. For that purpose the Federal Highway Research Institute (BASt) uses the emission- and calculation tool TREMOD (Transport Emission Model) which provides baseline data and calculated results for pollutants in almost every differentiation e.g. vehicle category, traffic situation and road type. Moreover, estimations of future emission trends, stock information and mileage distribution can be made. The main objective is to illustrate the impact of the upcoming emission standards Euro 4 and Euro 5 on the operational hydrocarbon emissions of powered two-wheelers based on statistical estimations. The significant aspect is to generate scenarios to show the reduction potential of hydrocarbon emissions of powered two-wheelers, differentiated into motorcycles and small motorcycles, in relation to the total share of hydrocarbon emissions in this vehicle class and to the total hydrocarbon emissions from road traffic. As a part of their research, the authors can make initial statements about the possible effect of the new emission standards of regulation (EU) No. 168/2013 by means of modeling with TREMOD.
There is considerable evidence for the negative effects of driver distraction on road safety. In many experimental studies, drivers have been primarily viewed as passive receivers of distraction. Thus, there is a lack of research on the mediating role of their self-regulatory behavior. The aim of the current study was to compare drivers' performance when engaged in a system-paced secondary task with a self-paced version of this task and how both differed from baseline driving performance without distraction. Thirty-nine participants drove in a simulator while performing a secondary visual"manual task. One group of drivers had to work on this task in predefined situations under time pressure, whereas the other group was free to decide when to work on the secondary task (self-regulation group). Drivers' performance (e.g., lateral and longitudinal control, brake reaction times) was also compared with a baseline condition without any secondary task. For the system-paced secondary task, distraction was associated with high decrements in driving performance (especially in keeping the lateral position). No effects were found for the number of collisions, probably because of the lower driving speeds while distracted (compensatory behavior). For the self-regulation group, only small impairments in driving performance were found. Drivers engaged less in the secondary task during foreseeable demanding or critical driving situations. Overall, drivers in the self-regulation group were able to anticipate the demands of different traffic situations and to adapt their engagement in the secondary task, so that only small impairments in driving performance occurred. Because in real traffic drivers are mostly free to decide when to engage in secondary tasks, it can be concluded that self-regulation should be considered in driver distraction research to ensure ecological validity.
Motorcycling is a fascinating kind of transportation. While the riders' direct exposure to the environment and the unique driving dynamics are essential to this fascination, they both cause a risk potential which is several times higher than when driving a car. This chapter gives a detailed introduction to the fundamentals of motorcycle dynamics and shows how its peculiarities and limitations place high demands on the layout of dynamics control systems, especially when cornering. The basic principles of dynamic stabilization and directional control are addressed along with four characteristic modes of instability (capsize, wobble, weave, and kickback). Special attention is given to the challenges of braking (brake force distribution, dynamic over-braking, kinematic instability, and brake steer torque induced righting behavior). It is explained how these challenges are addressed by state-of-the-art brake, traction, and suspension control systems in terms of system layout and principles of function. It is illustrated how the integration of additional sensors " essentially roll angle assessment " enhances the cornering performance in all three categories, fostering a trend to higher system integration levels. An outlook on potential future control systems shows exemplarily how the undesired righting behavior when braking in curves can be controlled, e.g., by means of a so-called brake steer torque avoidance mechanism (BSTAM), forming the basis for predictive brake assist (PBA) or even autonomous emergency braking (AEB). Finally, the very limited potential of brake and chassis control to stabilize yaw and roll motion during unbraked cornering accidents is regarded, closing with a promising glance at roll stabilization through a pair of gimbaled gyroscopes.
In line with the new definition introduced by the European Commission (EC), the number of seriously injured road casualties in Germany for 2014 is assessed in this study. The number of MAIS3+ casualties is estimated by two different methodological approaches. The first approach is based on data from the German Inâ€Depth Accident Study (GIDAS), which is closely related to the German Road Traffic Accident Statistics. The second approach is based on data from the German TraumaRegister DGU-® (TRâ€DGU), which includes many more hospitals but not all MAIS3+ injuries.
Camera-monitor systems (CMS) can be used in motor vehicles to display the driver's rear view on a monitor mounted inside the vehicle. This also offers the possibility of replacing conventional exterior mirrors with suitable CMS and thereby implementing new design concepts with aerodynamic advantages. However, as exterior mirrors are safety-relevant vehicle parts for securing the driver's indirect rear view (requirements specified in UN Regulation No. 46), the question arises whether CMS can provide an equivalent substitute for mirrors. In the scope of this study, CMS and conventional exterior mirrors were compared and assessed in test drives and static tests under different external conditions. On the one hand, the examination of technical aspects, and on the other hand, issues pertaining to the design of the human-machine interaction, were the objects of the study. Two vehicles were available for the trials with passenger vehicles: A vehicle, manufactured in small series, which is already equipped with CMS as sole replacement for the exterior mirrors, as well as a compact class vehicle which had a CMS retrofitted by the car manufacturer in addition to conventionally used exterior mirrors. The latter could be covered exclusively for trips with CMS. A tractor unit with semitrailer was available for the truck trials. The driver's cabin was equipped with a CMS system developed by the vehicle manufacturer. In general, it was shown that it is possible to display the indirect rear view sufficiently for the driver, both for cars and trucks, using CMS which meet specific quality criteria. Depending on the design, it is even possible to receive more information about the rear space from a CMS than is possible with mirror systems. It was also shown that the change from mirrors to CMS requires a certain period of familiarisation. However, this period is relatively short and does not necessarily result in safety-critical situations.