Abteilung Fahrzeugtechnik
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (90)
- Deutsch (51)
- Mehrsprachig (1)
Volltext vorhanden
- nein (142) (entfernen)
Schlagworte
- Safety (53)
- Sicherheit (53)
- Anfahrversuch (38)
- Vehicle (37)
- Bewertung (36)
- Evaluation (assessment) (36)
- Fahrzeug (36)
- Impact test (veh) (35)
- Test method (31)
- Prüfverfahren (29)
Institut
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
The objectives of the FIMCAR (Frontal Impact and Compatibility Assessment Research) project are to answer the remaining open questions identified in earlier projects (such as understanding of the advantages and disadvantages of force based metrics and barrier deformation based metrics, confirmation of specific compatibility issues such as structural interaction, investigation of force matching) and to finalise the frontal impact test procedures required to assess compatibility. Research strategies and priorities were based on earlier research programs and the FIMCAR accident data analysis. The identified real world safety issues were used to develop a list of compatibility characteristics which were then prioritised within the consortium. This list was the basis for evaluating the different test candidates. This analysis resulted in the combination of the Full Width Deformable Barrier test (FWDB) with compatibility metrics and the existing Offset Deformable Barrier (ODB) as described in UN-ECE Regulation 94 with additional cabin integrity requirement as being proposed as the FIMCAR assessment approach. The proposed frontal impact assessment approach addresses many of the issues identified by the FIMCAR consortium but not all frontal impact and compatibility issues could be addressed.
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for over 10 years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and the final report to the steering committee on frontal impact [Faerber 2007] and the FP5 VC-COMPAT[Edwards 2007] project activities, two test approaches were identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in current research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis will be performed. In the FIMCAR Deliverable D 3.1 [Adolph 2013] the development and assessment of criteria and associated performance limits for the full width test procedure were reported. In this Deliverable D3.2 analyses of the test data (full width tests, car-to-car tests and component tests), further development and validation of the full width assessment protocol and development of the load cell and load cell wall specification are reported. The FIMCAR full-width assessment procedure consists of a 50 km/h test against the Full Width Deformable Barrier (FWDB). The Load Cell Wall behind the deformable element assesses whether or not important Energy Absorbing Structures are within the Common Interaction Zone as defined based on the US part 581 zone. The metric evaluates the row forces and requires that the forces directly above and below the centre line of the Common Interaction Zone exceed a minimum threshold. Analysis of the load spreading showed that metrics that rely on sum forces of rows and columns are within acceptable tolerances. Furthermore it was concluded that the Repeatability and Reproducibility of the FWDB test is acceptable. The FWDB test was shown to be capable to detect lower load paths that are beneficial in car-to-car impacts.
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for over 10 years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in current research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The objectives of the work reported in this deliverable were to review existing full-width test procedures and their discussed compatibility metrics, to report recent activities and findings with respect to full-width assessment procedures and to assess test procedures and metrics. Starting with a review of previous work, candidate metrics and associated performance limits to assess a vehicle- structural interaction potential, in particular its structural alignment, have been developed for both the Full Width Deformable Barrier (FWDB) and Full Width Rigid Barrier (FWRB) tests. Initial work was performed to develop a concept to assess a vehicle- frontal force matching. However, based on the accident analyses performed within FIMCAR frontal force matching was not evaluated as a first priority and thus in line with FIMCAR strategy the focus was put on the development of metrics for the assessment of structural interaction which was evaluated as a first priority.
Cost benefit analysis
(2014)
Although the number of road accident casualties in Europe is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities [EC 2012]. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car- safety performance in frontal impacts is to improve its compatibility for car-to-car impacts and for collisions against objects and HGVs. Compatibility consists of improving both a car- self and partner protection in a manner such that there is good interaction with the collision partner and the impact energy is absorbed in the car- frontal structures in a controlled way which results in a reduction of injuries. Over the last ten years much research has been performed which has found that there are four main factors related to a car- compatibility [Edwards 2003, Edwards 2007]. These are structural interaction potential, frontal force matching, compartment strength and the compartment deceleration pulse and related restraint system performance. The objective of the FIMCAR FP7 EC-project was to develop an assessment approach suitable for regulatory application to control a car- frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation.
The objective of this deliverable is to describe the expected influence of the candidate test procedures developed in FIMCAR for frontal impact on other impact types. The other impact types of primary interest are front-to-side impacts, collisions with road restraint systems (e.g. guardrails), and heavy goods vehicle impacts. These collision types were chosen as they involve structures that can be adapted to improve safety. Collisions with vulnerable road users (VRU) were not explicitly investigated in FIMCAR. It is expected that the vehicle structures of interest in FIMCAR can be designed into a VRU friendly shell. Information used for this deliverable comes from simulations and car-to-car crash tests conducted in FIMCAR or review of previous research. Three test configurations (full width, offset, and moving deformable barriers) were the input to the FIMCAR selection process. There are three different types of offset tests and two different full width tests. During the project test procedures could be divided into three groups that provide different influences or outcomes on vehicle designs: 1. The ODB barrier provides a method to assess part of the vehicles energy absorption capabilities and compartment test in one test. 2. The FWRB and FWDB have similar capabilities to control structural alignment, further assess energy absorption capabilities, and promote the improvements in the occupant restraint system for high deceleration impacts. 3. The PDB and MPDB can be used to promote better load spreading in the vehicle structures, in addition to assessing energy absorption and occupant compartment strength in an offset configuration. The consortium selected the ODB and FWDB as the two best candidates for short term application in international rulemaking. The review of how all candidates would affect vehicle performance in other impacts (beside front-to-front vehicle or frontal impacts with fixed obstacles) however is reported in this deliverable to support the benefit analysis reported in FIMCAR. The grouping presented above is used to discuss all five test candidates using similarities between certain tests and thereby simplify the discussion.
Accident analysis
(2014)
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the EC funded FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in today- research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The specific objectives of the work reported in this deliverable were: - Determine if previously identified compatibility issues are still relevant in current vehicle fleet: Structural interaction, Frontal force matching, Compartment strength in particular for light cars. - Determine nature of injuries and injury mechanisms: Body regions injured o Injury mechanism: Contact with intrusion, Contact, Deceleration / restraint induced. The main data sources for this report were the CCIS and Stats 19 databases from Great Britain and the GIDAS database from Germany. The different sampling and reporting schemes for the detailed databases (CCIS & GIDAS) sometimes do not allow for direct comparisons of the results. However the databases are complementary " CCIS captures more severe collisions highlighting structure and injury issues while GIDAS provides detailed data for a broader range of crash severities. The following results represent the critical points for further development of test procedures in FIMCAR.
The off-set assessment procedure potentially contributes to the FIMCAR objectives to maintain the compartment strength and to assess load spreading in frontal collisions. Furthermore it provides the opportunity to assess the restraint system performance with different pulses if combined with a full-width assessment procedure in the frontal assessment approach. Originally it was expected that the PDB assessment procedure would be selected for the FIMCAR assessment approach. However, it was not possible to deliver a compatibility metric in time so that the current off-set procedure (ODB as used in UNECE R94) with some minor modifications was proposed for the FIMCAR Assessment Approach. Nevertheless the potential to assess load spreading, which appears not to be possible with any other assessed frontal impact assessment procedure was considered to be still high. Therefore the development work for the PDB assessment procedure did not stop with the decision not to select the PDB procedure. As a result of the decisions to use the current ODB and to further develop the PDB procedure, both are covered within this deliverable. The deliverable describes the off-set test procedure that will be recommended by FIMCAR consortium, this corresponds to the ODB test as it is specified in UN-ECE Regulation 94 (R94), i.e. EEVC deformable element with 40% overlap at a test speed of 56 km/h. In addition to the current R94 requirements, FIMCAR will recommend to introduce some structural requirements which will guarantee sufficiently strong occupant compartments by enforcing the stability of the forward occupant cell. With respect to the PDB assessment procedure a new metric, Digital Derivative in Y direction - DDY, was developed, described, analysed, and compared with other metrics. The DDY metric analyses the deformation gradients laterally across the PDB face. The more even the deformation, the lower the DDY values and the better the metric- result. In order analyse the different metrics, analysis of the existing PDB test results and the results of the performed simulation studies was performed. In addition, an assessment of artificial deformation profiles with the metrics took place. This analysis shows that there are still issues with the DDY metric but it appears that it is possible to solve them with future optimisations. For example the current metric assesses only the area within 60% of the half vehicle width. For vehicles that have the longitudinals further outboard, the metric is not effective. In addition to the metric development, practical issues of the PDB tests such as the definition of a scan procedure for the analysis of the deformation pattern including the validation of the scanning procedure by the analysis of 3 different scans at different locations of the same barrier were addressed. Furthermore the repeatability and reproducibility of the PDB was analysed. The barrier deformation readings seem to be sensitive with respect to the impact accuracy. In total, the deliverable is meant to define the FIMCAR off-set assessment procedure and to be a starting point for further development of the PDB assessment procedure.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
The technology involved in traffic control in Germany has undergone significant changes. This paper describes how a group of German manufacturers have worked with operators to produce Open Communications Interface for Road Traffic Control Systems (OCIT). At the beginning of 2010, twenty-one different European manufacturers had bought licences for OCIT outstations.
The Joint Transport Research Centre of the Organisation for Economic Co-operation and Development and the International Transport Forum recently conducted a benchmarking study of the safety and productivity of typical highway transport trucks from various countries. This paper focuses on vehicle productivity and efficiency in regard to the movement of freight. Forty vehicles from 10 countries were examined. The vehicles were designed for longer-haul applications and were classified in three separate categories: workhorse vehicles, which are the most common and can travel on most roads; high-capacity vehicles, which may be restricted to a certain class of road; and very high-capacity vehicles, which may be restricted to specific highways or routes. The metrics used in the analysis include maximum cargo mass and volume capacity, optimum cargo density, fuel consumption, and carbon dioxide output as a function of the freight task. The study found that size and weight regulations have a significant effect on the productivity and efficiency of heavy vehicles, including fuel consumption and vehicle emissions per unit of cargo transported. Significant variations were found among the vehicles from participating countries as well as within vehicle classes. It was also apparent that, in general, higher-productivity vehicles are correlated more strongly with increased cargo volume than with increased cargo mass and that larger trucks are better suited to lower-density freight than are workhorse vehicles. The study also found that it is important to consider the freight task when evaluating vehicle fuel consumption and emissions.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.
This paper describes the methodology for the assessment of the socio-economic impact of SAFESPOT applications. The applications selected for the assessment cover vehicle to vehicle (v2v) as well as vehicle to infrastructure (v2i) communication systems. The applications address main problem areas of road safety: accidents at intersections, accidents due to hazardous road and weather conditions and accidents due to over speeding and inappropriate distance. The assessment methodology relies in its core on cost-benefit analysis (CBA) as the most widespread tool to assess the profitability of applications form the society point of view. The assessment is however not limited to CBA but also considers the economic effects for particular stakeholder groups such as users, public authorities and the like. Their individual cost and benefits can be investigated in stakeholder analyses. Both elements, CBA and stakeholder analysis, form an integrated assessment approach which is applied here. The assessment makes use of the sound methodological base which was provided by projects such as SEiSS and eIMPACT. Some characteristics of co-operative systems however call for special attention within the assessment. Most prominently, the assessment will concentrate on a bundle of applications. The impact of this bundle will be assessed under the conditions of different business and service models. These issues will be addressed in the paper. Moreover, this paper also provides insight in likely patterns of results and first results of socio-economic impact assessment itself.
Mit der EU-Verordnung Nummer 661/2009 zur Typgenehmigung und allgemeinen Sicherheit von Kraftfahrzeugen wird von der EU für schwere Nutzfahrzeuge der Einbau von Spurverlassenswarnsystemen und automatischen Notbremssystemen vorgeschrieben. Mit dem obligatorischen Einbau der Systeme wird eine Reduktion der Abkommens- und Auffahrunfälle von Nutzfahrzeugen aus den Klassen M2, M3, N2 und N3, die auf Grund der hohen Masse der Fahrzeuge folgenschwer sind, erwartet. Als Einführungsdaten werden der 1. November 2013 für neue Fahrzeugtypen und der 1. November 2015 für neue Fahrzeuge genannt. Leistungsanforderungen beziehungsweise technische Spezifikationen, denen die Systeme genügen müssen, liegen jedoch noch nicht vor. Diese werden derzeit von einer Expertengruppe auf UN-ECE-Ebene entwickelt. Dabei wird versucht, technologieneutrale Beschreibungen für die Ausgestaltung der Systeme zu erstellen, die gleichzeitig sowohl den gewünschten Nutzen für die Verkehrssicherheit garantieren, sich aber auch an der derzeit vorhandenen und realisierbaren Technologie orientieren. Darüber hinaus müssen die Systemkosten in einem vernünftigen Verhältnis zum Sicherheitsnutzen stehen. Ziel ist es, im Laufe des Jahres 2011 Vorschläge für die Legislative vorzulegen. Es wird über den Stand der Arbeiten, offene Fragestellungen, Herausforderungen bei der Ausgestaltung der technischen Anforderungen sowie sich abzeichnende Ergebnisse berichtet. Dabei sind die Arbeiten in Bezug auf Lane Departure Warning Systems (LDWS) bereits weiter fortgeschritten als zu Advanced Emergency Braking Systems (AEBS).
Falltests zur Untersuchung der Belastungen von Dummys beim Aufprall auf den Boden, Teil 1 und 2
(2010)
Beim Zusammenprall eines Motorrads mit einem Pkw unterscheidet man in der Unfallforschung sowohl den Erstanprall des Motorradfahrers an den Pkw als auch den Sekundäraufprall des Motorradfahrers auf dem Boden. So genannte Full-Scale-Crashtests mit Dummys haben beim Erstanprall gezeigt, dass Motorradfahrer durch Airbags potenziell geschützt werden können. Bei den entsprechenden Unfallsimulationen wurde jedoch im weiteren Bewegungsablauf beim nachfolgenden Sekundäraufprall auf dem Boden festgestellt, dass relativ hohe Belastungen auf den Dummy einwirken. Es stellt sich hierbei jedoch die Frage, ob die üblicherweise für Lasteinwirkungen im Falle eines Erstanpralls entwickelten und validierten Dummys die bei einem Sekundäraufprall auf einen Motorradfahrer einwirkenden Belastungen hinreichend genau wiedergeben können. Dazu wurden die Belastungen eines Dummys beim Aufprall auf den Boden untersucht, um das Verletzungsrisiko eines menschlichen Motorradfahrers einschätzen zu können. Im Dekra-Crash-Test-Center wurden vier verschiedene Aufprallsituationen mit einem Hybrid III Dummy durchgeführt, wobei diese Tests an eine andere Testreihe angelehnt sind, die bereits am US-amerikanischen Institut "Dynamic Research International" (DRI) durchgeführt worden waren. Nach der Erläuterung des Testaufbaus und seiner Durchführung wird detailliert auf die gemessenen Verzögerungsbelastungen des Dummys eingegangen. Hierbei geben zum einen Tabellen eine Übersicht über charakteristische Messwerte zur Quantifizierung der maximalen Belastung des Dummys, zum anderen veranschaulichen Bilder die zugehörigen zeitlichen Verzögerungsverläufe in Becken, Brust und Kopf des Dummys. Der Artikel schließt mit einer Interpretation der Versuchsergebnisse und gibt einen Ausblick auf den weiteren Untersuchungsbedarf.
This article describes the development of techniques to minimize automobile driver distraction when an in-vehicle information systems (IVIS) that requires visual attention is in use. The authors explain the visual occlusion technique that has been developed as a tool for the assessment of the in-vehicle human-machine interface (HMI) of IVIS in terms of visual demands. The authors addressed an unresolved issue in previous standardized experimental protocols - how subjects make use of the occluded intervals and how this might affect the assessments of visual demands. This study protocol assumed that subjects would continue task performance during occluded periods, leading to an underestimation of visual demands by the occlusion parameters "total shutter open time" (TSOT) and the "occlusion index". The authors predicted that a simple additional loading task to be performed in parallel could disrupt IVIS task performance during the occluded period leading to higher estimations of visual demands by TSOT and R. Their prediction was confirmed by the study findings. The results also showed that under the condition of additional auditory tracking, TSOT and R discriminated more clearly between an "easy" and a "difficult" IVIS task than under the standard condition. They conclude with a discussion of the implications of this research for designers of assessment tools for driver visual distractions.