91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
Volltext vorhanden
- nein (133) (entfernen)
Schlagworte
- Sicherheit (58)
- Safety (57)
- Bewertung (40)
- Evaluation (assessment) (40)
- Vehicle (39)
- Fahrzeug (38)
- Anfahrversuch (34)
- Impact test (veh) (31)
- Conference (28)
- Test method (28)
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Vor dem Hintergrund der derzeitigen Verkehrs- und Unfallsituation sowie verkehrsrechtlicher Vorschriften wurde durch Auswertung humanwissenschaftlicher und technischer Literatur eine Sachstandsbeschreibung erstellt, die die in Zusammenhang mit Auffahrunfällen und ihrer Verhinderung stehenden Aspekte aufzeigt. Als fahrzeugtechnische Hilfen zur Einhaltung eines ausreichenden Abstandes zwischen hintereinander fahrenden Fahrzeugen werden dabei vorrangig autarke Systeme - das sind solche, bei denen sich alle notwendigen Vorrichtungen im Fahrzeug befinden - betrachtet. Möglichkeiten und Grenzen der bekannten technischen Hilfsmittel, insbesondere der Abstandswarn- und Abstandsregelungseinrichtungen werden aufgezeigt. Es stellte sich heraus, dass den Warnstrategien sowie ihren Auswirkungen auf den Verkehrsablauf und die Verkehrssicherheit besondere Bedeutung zukommt. In diesem Zusammenhang werden auch Zielkonflikte, insbesondere zwischen Sicherheitsforderungen und Fahrerakzeptanz, deutlich. Im Teil I des Berichts erfolgt die zusammenfassende Beschreibung und kritische Wertung des Sachstandes. Im Teil II werden die Auswerteergebnisse zu den angesprochenen Fragenkomplexen im einzelnen dargestellt. Teil III enthält eine Kurzdokumentation der für die Erstellung des Berichts wesentlichsten Literaturstellen.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.
Ziel des Forschungsvorhabens war es, durch gezielte Auswertung des Unfallgeschehens den Einfluss von Fahrerverhaltensweisen beziehungsweise -merkmalen und technischen Fahrzeugparametern auf die Unfallhäufigkeit und die Unfallart zu ermitteln. Zunächst wurde eine Auswertung der Literatur und die Beschaffung und Aufbereitung des Datenmaterials vorgenommen. Die Grundlage der Auswertungen bildeten die Unfälle mit Pkw-Beteiligung im Bundesland Nordrhein-Westfalen aus dem Jahre 1980. Die Datensätze waren vom Kraftfahrt-Bundesamt in Flensburg um fahrzeugtechnische Angaben erweitert worden. Zur Relativierung der Unfallzahlen wurden fahrzeugtypenspezifische jährliche Fahrleistungen und Bestände berechnet. Weiterhin wurde das Geschwindigkeitsverhalten im freien Verkehr in Abhängigkeit vom Fahreralter sowie vom Fahrzeugtyp ermittelt. Um die Wechselwirkungen von Fahrer- und Fahrzeugeigenschaften im Unfallgeschehen unabhängig voneinander betrachten zu können, war es notwendig, einen "Normalfahrer" zu definieren. Der "Normalfahrer" wurde anhand von Analysen ausgewählter Unfallsituationen mit dem Ziel beschrieben, mit diesen Fahrern Fahrversuche mit Pkw durchführen zu können, deren Ergebnisse weder durch besonders gute noch durch besonders schlechte, sondern vielmehr durch eine durchschnittliche Eignung des Fahrers zum Führen eines Kraftfahrzeuges geprägt sein sollen. Anhand dieser Fahrversuche sollen Grenzen von Kennwerten, die Fahrzeugeigenschaften und das Fahrverhalten beschreiben, abgeleitet werden, die sich als dem "Normalfahrer" angepasst erweisen. Aufgrund der aufgezeigten Zusammenhänge zwischen dem Fahreralter und der ursächlichen Beteiligung an bestimmten Unfalltypen ist es nunmehr möglich, durchschnittlich gute Fahrer als Probanden auszuwählen, die je nach Art des Versuches entweder zur Gruppe der jüngeren und älteren Fahrer gehören. Nach vorheriger Festlegung eines Anteilswertes von Fahrern, die als "normal" anzusehen sind, können bei gleichzeitiger Berücksichtigung der für jüngere und ältere Fahrer typischen Versagensarten die Altersintervalle bestimmt werden, aus denen die "Normalfahrer" für die Fahrversuche auszuwählen sind.
Beschrieben wird die Evaluierung eines Testverfahrens der Arbeitsgruppe 10 des European Experimental Vehicle Committee, mit dem die "Fußgängerverträglichkeit" von Frontflächen von Personenkraftwagen bestimmt werden kann. Dabei werden verschiedene Anprallarten von Fußgängern an Fahrzeugen simuliert: der Anprall eines Beines an den Stoßfänger, der Anprall des Oberschenkels an die Vorderkante der Fronthaube und der Anprall des Kopfes auf die Fronthaube. Im Beitrag wird auf die Durchführung von Tests zum Oberschenkelanprall und zum Beinanprall an drei verschiedenen Fahrzeugtypen eingegangen. Beschrieben werden Testverfahren, Versuchsaufbau und Versuchsdurchführung. Die Versuchsreihe zeigte, dass das entwickelte Testverfahren praktikabel ist.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
Since integrated safety systems combine active and passive safety elements in one safety system, it is necessary to define new procedures to evaluate vehicle safety from the overall system point of view. The main goal of the ASSESS project is to develop harmonized and standardized assessment procedures for collision mitigation and avoidance systems. Methods and Data Sources: In ASSESS, procedures are developed for: driver behaviour evaluation, pre-crash system performance evaluation, crash performance evaluation, socio-economic assessment. This paper will concentrate on the activities related to the crash evaluation. The objective is to perform simulations, sled tests and crash tests in order tounderstand the influence of the activation of the pre-crash systems on the occupants" injuries during the crash phase. When a traffic accident is unavoidable, pre-crash systems work on various safety devices in order to improve the vehicle occupants" protection. Braking assistance and adaptive restraint systems are the main pre-crash systems whose effect on the occupants" protection will be described in this paper. Results: The results will be a description of the effect of the activation of the pre-crash systems on the crash phase. Additionally, a set of recommendations for future methodology developments will be delivered. Furthermore, a first approach to the study of the effect of the pre-crash systems activation on the occupants" protection when the impact is unavoidable will be presented. This effect will be quantified using the biomechanical values obtained from the simulation and testing activities and their related injury risks. Simulation and testing activities will consider the following scenarios: - No activation of any pre-crash system, - Activation of one or a combination of several pre-crash systems. In this way, differences in the results obtained from different scenarios will show the effect of each pre-crash system separately during the crash phase. Discussion and Limitations: The set of activities developed in this research project is limited by the fact that with the given resources only a limited number of vehicle models could be investigated. In addition, there are also limitations related to the injury risk curves and the passive safety tools currently on the market. Conclusion and Relevance to session submitted: The paper will present a complete analysis of the effect of pre-crash systems during the crash phase when the impact is unavoidable. Details, limitations and first application experience based on a few examples will be discussed. Currently, there is not any regulation, assessment program, or other similar official procedure able to assess pre-crash systems during the crash phase. This project comprises phases of traffic accidents which have been historically analysed separately, and aims to evaluate them taking into account their interrelationship. ASSESS is one of the first European projects which deals in depth with the concept of integrated safety, defining methodologies to analyse vehicle safety from a global point of view.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
Das Projekt IMPROVER (Impact Assessment of Road Safety Measures for Vehicles and Road Equipment / Wirkungsanalyse und Bewertung von verschiedenen Verkehrssicherheitsmaßnahmen) wurde im Auftrag der Europäischen Kommission (Generaldirektion Energie und Verkehr) bearbeitet, um die folgenden Straßenverkehrssicherheitsaspekte zu untersuchen: den Einfluss der wachsenden Zahl von Sport Utility Vehicles (SUV) und Multi Purpose Vehicles (MPV) auf Verkehrssicherheit, Kraftstoffverbrauch und Emissionen; die Bewertung von Maßnahmen zur Verbesserung der Verkehrssicherheit von leichten Nutzfahrzeugen; die Auswirkungen des Tempomaten auf Verkehrssicherheit, Kraftstoffverbrauch und Emissionen; die Harmonisierung von Verkehrszeichen und Markierungen auf dem Transeuropäischen Straßennetz (TERN) unter Verkehrssicherheitsgesichtspunkten. Das Projekt wurde von der Bundesanstalt für Straßenwesen (BASt) zusammen mit 14 Partnerinstituten von November 2004 bis Mai 2006 bearbeitet. Entsprechend den Aufgaben wurde das Projekt in vier voneinander unabhängige Subprojekte eingeteilt. Der vorliegende Artikel gibt eine Übersicht über die in den jeweiligen Unterprojekten geleisteten Arbeiten, deren Ergebnisse und die daraus abgeleiteten Empfehlungen.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben. Das Ergebnis kann indes nicht zufriedenstellen. Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird im Beitrag, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der sich auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschrieben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen; dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
Automatische Lenkfunktionen sind abgesehen von korrigierenden Lenkeingriffen entsprechend der UN-Regelung Nr. 79 bisher nur in einem Geschwindigkeitsbereich bis 10 km/h erlaubt. Die Weiterentwicklung der Technik im Bereich der Fahrerassistenzsysteme und der Automatisierung der Fahraufgabe wuerden es jedoch technisch erlauben, automatische Lenkfunktionen auch bei höheren Geschwindigkeiten einzusetzen. Neben einem Zugewinn an Komfort wird von diesen Systemen auch ein Beitrag zur Erhöhung der Verkehrssicherheit erwartet. Dieses Verkehrssicherheitspotenzial wird man jedoch nur ausschöpfen können, wenn die automatisierten Lenksysteme entsprechend gestaltet sind. Insbesondere sollten mögliche Risiken auf Grund automatischen Lenkens minimiert sein. Aus diesen Gründen laufen derzeit Arbeiten auf UNECE-Ebene, die Regelung Nr. 79 über einheitliche Bedingungen für die Genehmigung der Fahrzeuge hinsichtlich der Lenkanlage in Bezug auf automatische Lenkfunktionen (ACSF = Automatically Commanded Steering Functions) zu überarbeiten, um diese unter bestimmten Bedingungen auch bei höheren Geschwindigkeiten genehmigen zu können. Der vorliegende Beitrag reflektiert diese Arbeiten und stellt die Entwicklung der technischen Anforderungen an automatisches Lenken und der für die fahrzeugtechnischen Vorschriften vorgesehenen Testprozeduren dar.
Entwicklung eines Prüfverfahrens zur Beurteilung der Hochgeschwindigkeitsstabilität von Motorrädern
(1991)
Ziel des Forschungsvorhabens war die Erarbeitung eines Prüfverfahrens, welches die objektive Beurteilung der Hochgeschwindigkeitsstabilität von Motorrädern ermöglicht. Insgesamt beteiligten sich 17 Fahrer an den Fahrversuchen, die auf der Hochgeschwindigkeitsstrecke eines Prüffeldes erfolgten. Zum Einsatz kamen vier Motorradmodelle, von denen zwei jeweils mit und ohne Gepäck erprobt wurden. Ein eindeutiger Zusammenhang zwischen der Hochgeschwindigkeitsstabilität von Motorrädern und grundlegenden Fahrerparametern war nur in einem Punkt zu erkennen: Oberhalb einer im Zusammenhang mit den Untersuchungen ermittelten Mindestfahrerfahrung kann ein Einfluss weitergehender Fahrerfahrung ausgeschlossen werden. Die anderen untersuchten, objektiv leicht messbaren Fahrerparameter waren Körpergröße und Masse. Eindeutig isolierbare Zusammenhänge zwischen der Pendeldämpfung und einem dieser Werte waren nicht festzustellen. Bei einem der beiden mit Gepäck untersuchten Motorrädern wurde in Analogie zu früheren Untersuchungen ermittelt, dass die Zuladung die Pendeldämpfung reduziert. Bei Mitnahme eines Beifahrers stellten sich höhere Dämpfungsgrade ein als bei den überwiegend durchgeführten Solofahrten. Das vorgeschlagene Prüfverfahren basiert größtenteils auf den Ergebnissen früherer Untersuchungen und enthält eine engere Beschreibung des einzusetzenden Versuchsfahrers. Weiterhin wurde zusätzlich die Beladung mit Gepäck im üblichen Rahmen in den vorgeschlagenen Prüfungsablauf aufgenommen.
Es wird die Entwicklung einer Anlage zur Zählung von Fahrzeugachsen, die eine Straße überrollen, beschrieben. Diese Anlage gestattet, je nach Konfiguration, eine getrennte Erfassung von Pkw, Lkw und spikesbereiften Achsen. Eine Aufzeichnung der Zählergebnisse in vorwählbaren Zeitabständen (1 Stunde bis 1 Tag) auf einem Datenträger (z.B. 5-Kanal-Lochstreifen) kann vorgenommen werden. Mehrere Anlagen in verschiedenen Konfigurationen sind z.T. seit Jahren in Betrieb. Netz- und Batteriebetrieb sind möglich. Beispiele für Ergebnisse mit je nach Anlagentyp unterschiedlicher Aussagekraft werden gegeben.
Ziel der vorliegenden Arbeit war es, eine möglichst umfassende Literaturstudie zu erstellen, die die Möglichkeiten und Probleme aufzeigt, die beim Einsatz von Kunststoffen in Kraftfahrzeugen auftreten können. Der Begriff "Kunststoffe" ist sehr weitreichend, so dass es zweckmäßig war, den Gesamtkomplex zu unterteilen. Die ausgewählte Gliederung richtet sich einerseits nach Werkstoffgruppen und andererseits nach übergeordneten Gesichtspunkten. Die Studie wurde daher in folgende, in sich geschlossene Abschnitte unterteilt. 1. Entwicklungen und Tendenzen beim Kunststoffeinsatz, 2. Rechtsvorschriften, 3. Eigenschaften und Anwendung von Kunststoffen, 4. Elastomere, 5. Textilien und Schaumstoffe, 6. Lacke und Beschichtungsstoffe, 7. Klebtechnik, 8. Alterung, 9. Brandverhalten/Brennverhalten, 10. Recycling. Insgesamt wurden annähernd eintausend Literaturstellen erfasst. Dabei handelt es sich vorwiegend um Publikationen, die zwischen 1980 und 1988 erschienen sind. Die an den Werkstoffen orientierte Gliederung ermöglicht einen guten Überblick über alle Verwendungsbereiche der jeweiligen Werkstoffgruppe beziehungsweise über zusammenfassende Problemstellungen. Damit unterscheidet sich diese Studie von anderen Literaturzusammenstellungen, die sich in der Regel auf spezielle Teile des Kraftfahrzeuges, wie beispielsweise Motor- oder Innenraum, beschränken. Allerdings werden in dieser Studie nur Probleme bezüglich des Einsatzes von Kunststoffen in Pkw behandelt. Die Studie kann vor allem solchen Institutionen beziehungsweise Personen dienen, für die werkstoffbezogene Übersichten wichtig sind, und die sie als Basis für die Einarbeitung in Einzelprobleme nutzen wollen. Eine Weiterführung der Arbeit auf diesem Gebiet ist wünschenswert. Dabei wäre insbesondere auf die Schwerpunkte 1. Schadensfrüherkennung "life monitoring", 2. Verbesserung der Stoßabsorption, 3. Alterungsverhalten von Klebeverbindungen, 4. On-line-Lackierung unter den Belangen des Umweltschutzes, 5. Reduzierung der Verwendung von Lösemitteln und 6. Reduzierung des Shreddermülls (Rückgewinnung sortenreiner Polymerwerkstoffe) einzugehen.
Künftig sollen in Kfz-Scheinwerfern anstelle von Glühlampen auch Gasentladungslampen eingesetzt werden können. Hierbei handelt es sich um Hochdruckentladungslampen, die sich von bisher eingesetzten Halogen-Glühlampen durch die spektrale Verteilung ihres Lichtes, eine höhere Leuchtdichte und einen größeren Lichtstrom - bei geringerer elektrischer Aufnahmeleistung - unterscheiden. Derzeit werden Lampen unter der Bezeichnung D 1 in ein deutsches Fahrzeug der gehobenen Klasse eingebaut. Im Rahmen einer Vorstudie innerhalb des Projektes wurden die folgenden Punkte untersucht: - Integrierbarkeit der Lampe und des Scheinwerfers in bestehende Regelungen; - lichttechnische Eigenschaften der Gasentladungssysteme wie Zünd- und Anlaufverhalten in unterschiedlichen Betriebszuständen; - Farbwiedergabe retroreflektierender Verkehrszeichen und Signaleinrichtungen; - Leuchtdichtekontraste bei retroreflektierenden Materialien und Rückstrahlern; - Sicherheitsaspekte; - Blendung des Gegen- und des vorausfahrenden Verkehr. In der anschließenden Hauptstudie wurden Vorwärtsreflexion an Fahrbahnoberflächen zur Bestimmung der indirekten Blendung im trockenen und nassen Zustand; - spektrale Reflexion von Fahrbahndecken; - Streuleuchtdichten vor dem Fahrzeug bei Schlechtwettersituationen; - Blendungsunterschiede zwischen konventionellen und Gasentladungs-Systemen; - Gradient der Hell-Dunkel-Grenze untersucht. Bei der Untersuchung der Vorwärtsreflexion zeigte sich, dass sich bei nassen Fahrbahnoberflächen das Maximum der Reflexion in Fahrtrichtung verschiebt. In Schlechtwettersituationen wurde durch den größeren Lichtstrom ein Anstieg der Streuleuchtdichte gemessen. Aus diesem Grunde scheint eine Begrenzung der Vorfeldbeleuchtungsstärke sinnvoll. Aufgrund der Fahrzeugdynamik ergeben sich verschiedene Gradienten der Hell-Dunkel-Grenzen. Sie sind abhängig vom Fahrzeugtyp sowie von der Ausstattung der Fahrzeuge mit Niveauregulierung und automatischer Leuchtweitenregelung. Es ergab sich bei Verwendung von Gasentladungssystemen eine Erhöhung der Blendung. Die Blendbeleuchtungsstärken lagen dabei höher als bei vergleichbaren Halogensystemen. Ebenso wird durch die Vorwärtsreflexion auf der Fahrbahnoberfläche eine erhöhte Blendbeleuchtungsstärke bewirkt. Es zeigte sich, dass insbesondere zur Ermittlung der Beeinflussung älterer Verkehrsteilnehmer durch Gasentladungslampen weitere Untersuchungen erforderlich sind.
EEVC Status report
(2001)
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
Das Ziel der Untersuchung war, die Grenzen der Belastbarkeit eines Rollstuhl- und Personenrückhaltesystems mit Kraftknoten nach DIN 75078-2 zu ermitteln. Dazu wurden dynamische Schlittenversuche durchgeführt, bei denen die Verzögerungspulse sowie das Gesamtgewicht von Rollstuhl und Prüfpuppe variiert wurden. Für die Untersuchungen kamen ein Prüfrollstuhl, definiert nach ISO 10542, und Rückhaltesysteme mit Kraftknoten gemäß DIN 75078-2 zum Einsatz. Das Rückhaltesystem bestand aus einem Rollstuhl- und einem Personenrückhaltesystem, wobei das Rollstuhlrückhaltesystem (RRS) mit vier bzw. sechs Gurten und entsprechenden Retraktoren an einem dynamischen Schlittenaufbau befestigt wurde. Das Personenrückhaltesystem (PRS) bestand aus einem am Rollstuhl integrierten Beckengurt sowie einem Schulterschräggurt, der am Beckengurt und am Schlittenaufbau befestigt wurde. Ferner wurden bei den Versuchen Prüfpuppen verschiedener Alters- und Gewichtsklassen (P6, HIII 5 %, HIII 50 % und HIII 95 %) eingesetzt Die Belastungsanforderungen für das Rückhaltesystem wurden sukzessiv erweitert, indem einerseits das Gesamtgewicht (Rollstuhl und Prüfpuppe) und andererseits auch die Verzögerungspulse bis zur Versagensgrenze erhöht wurden. Das Vier-Gurt-Rückhaltesystem konnte bei einem Verzögerungspuls von 10 g einem Gesamtgewicht von bis zu 221 kg standhalten. Bei einem Verzögerungspuls von 20 g und einem Gesamtgewicht von 134 kg wurde das Vier-Gurt-System bis über die Grenzen belastet. Das Sechs-Gurt-Rückhaltesystem hat Belastungen bis 221 kg standgehalten. Infolgedessen ist bei einer Erhöhung der Verzögerungspulse auf 20 g und einem Gesamtgewicht von mehr als 109 kg ein Sechs-Gurt-System zu empfehlen.
The UN Regulation No. 79 is going to be amended to allow automatically commanded steering functions (ACSF) at speeds above 10 km/h. Hence, requirements concerning the approval of automatically performed steering manoeuvres have to be set in order to allow safe use of automatic steering on public roads as well as improve overall road safety for the driver and the surroundings. By order of the German Federal Ministry of Transport and Digital Infrastructure (BMVI), BASt developed and verified physical test procedures for automatic steering to be implemented in UN Regulation No. 79. The usability of currently available test tools was examined. The paper at hand describes these test procedures and presents results from verification tests. The designated tests are divided in three sections: functionality tests, verifications for the transition of control and emergency tests. System functionality tests are auto matic lane keeping, automatic lane change and an automatic abort of an initiated lane change due to traffic. Those tests check if the vehicle remains in its lane (under normal operating conditions), is able to perform safe automatic lane change manoeuvres and if it considers other road users during its manoeuvres. Transition tests examine the vehicle's behaviour when the driver fails to monitor the system and in situations when the system has to hand over the steering control back to the driver. For instance these tests provoke driver-in-the-loop requests by approaching system boundary limitations, like missing lane markings, surpassing maximum lateral acceleration in a bend or even a major system failure. Even further the driver and his inputs are monitored and if the system detects that he is overriding system actions or contrary want to quit the driving task and unfastens the seat belt, it has to shut down and put the human back into manually control and the responsibility of driving. The last series of test consists of two emergency situations in which the system has to react to a time critical event: A hard decelerating vehicle and a stationary vehicle in front both with no lane change possibility for the ACSF vehicle. Some of the tests, especially the emergency manoeuvres, require special target vehicles and propulsion systems. Since no fully automatic steering vehicles are available, a current Mercedes E-Class with Mercedes' "drive pilot" system was used. It was shown that the vehicle is automatically able to brake to a full stop towards a static Euro NCAP target from partial-automatic driving at 90 km/h, that it could brake towards a rapidly decelerating lead vehicle when travelling at 70 km/h, that it was able during partially automatic driving to remain in its lane in normal operation conditions and to perform a automatic (driver initiated) lane change while surveilling the driver- activities.
Das von der Bundesanstalt für Straßenwesen in Auftrag gegebene Projekt FP 8716 mit dem Thema "Sicherheitsrelevanz neuer Fahrhilfen in Kraftfahrzeugen" ist vom Institut für Kraftfahrwesen der TH Aachen auf der Basis einer rein theoretischen Studie bearbeitet worden. Primäres Ziel der Arbeit war es, festzustellen, inwieweit die neuen Fahrhilfen dazu geeignet sind, die Verkehrssicherheit durch einen Gewinn an aktiver Sicherheit anzuheben.Aber auch der mögliche Einfluss auf das Verhalten des Fahrers aus psychologischer Sicht war zu berücksichtigen, denn dieser agiert in dem Bewusstsein einer erhöhten Fahrsicherheit seines mit derartigen Systemen ausgestatteten Fahrzeugs. Gegenstand der Untersuchung waren die Systeme: Anti-Blockier-Vorrichtung (ABV), Antriebs-Schlupf-Regelung (ASR), Sperrdifferential, Vierradantrieb, Vierradlenkung, geregeltes/gesteuertes Federungssystem.Sämtliche Systeme haben aus der Sicht des Technikers ihre Berechtigung im Fahrzeug durch Erhöhung von Mobilität und Fahrsicherheit. Dass dieses Potential nicht vollständig in eine Anhebung der Verkehrssicherheit umgesetzt werden kann, ist vor allem auf die Verhaltensanpassung seitens des Fahrers aufgrund des erhöhten subjektiven Sicherheitsgefühls zurückzuführen. Anhand von Handlungs- und Risikoverhaltensmodellen des Fahrers konnte die verbleibende Wirkung der Systeme abgeschätzt werden. Darüber hinaus wurde statistisches Material ausgewertet, um den Bezug der Systeme zum Unfallgeschehen festzustellen. Das ABV erwies sich als am ehesten geeignet, Unfälle zu verhindern oder Unfallfolgen zu mindern. Die Stabilität und die Lenkbarkeit wird bei Bremsungen an der Kraftschlussgrenze, wie sie in kritischen Situationen häufig auftreten, deutlich verbessert. Eine ASR bietet ähnliche Vorteile beim Beschleunigungsvorgang, dem allerdings nur eine geringe Bedeutung für die Pre-Crash-Phase zuzuschreiben ist. Das Sperrdifferential dient in erster Linie zur Erhöhung der Traktion und damit der Mobilität. Daneben kann der Vierradantrieb die Querdynamik auf niedrigen Reibwerten günstig beeinflussen und so auch die Fahrsicherheit anheben. Das verspricht auch die Vierradlenkung durch eine erhöhte Stabilität bei schnellen Lenkbewegungen. Es besteht aber gerade bei den Systemen Vierradlenkung und Vierradantrieb die Gefahr einer deutlichen Zunahme des subjektiven Sicherheitsgefühls auf Seiten des Fahrers mit dem unerwünschten Effekt einer unter Umständen riskanteren Fahrweise. Geregelte Federungssysteme sind in ihrer Wirkung auf den Regelkreis Fahrer-Fahrzeug nur schwer einzuschätzen, da sie das gesamte Fahrverhalten des Fahrzeugs beeinflussen. Die Bilanz für die Verkehrssicherheit dürfte bei diesem System positiv sein. Dem Gewinn an Fahrsicherheit durch den Einbau der Fahrhilfen steht das Gefährdungspotential durch eventuelle Fehlfunktionen gegenüber. Eine regelmäßige Überwachung erscheint deshalb vor allem für die ABV und die Vierradlenkung angebracht.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
Except for corrective steering functions automatic steering is up to now only allowed at speeds up to 10 km/h according to UN Regulation No. 79. Progress in automotive engineering with regard to driver assistance systems and automation of driving tasks is that far that it would be technically feasible to realise automatically commanded steering functions also at higher vehicle speeds. Besides improvements in terms of comfort these automated systems are expected to contribute to road traffic safety as well. However, this safety potential will only be exhausted if automated steering systems are properly designed. Especially possible new risks due to automated steering have to be addressed and reduced to a minimum. For these reasons work is currently ongoing on UNECE level with the aim to amend the regulation dealing with provisions concerning the approval of steering equipment. It is the aim to revise requirements for automatically commanded steering functions (ACSF) so that they can be approved also for higher speeds if certain performance requirements are fulfilled. The paper at hand describes the derivation of reasonable system specifications from an analysis of relevant driving situations with an automated steering system. Needs are explained with regard to covering normal driving, sudden unexpected critical events, transition to manual driving, driver availability and manoeuvres to reach a state of minimal risk. These issues form the basis for the development of test procedures for automated steering to be implemented in international regulations. This holds for system functionalities like automatic lane keeping or automatic lane change as well as for addressing transition situations in which the system has to hand over steering to the driver or addressing emergency situations in which the system has to react instead of the driver.
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
The objective was to develop and validate a crash trolley (reference vehicle) equipped with a compartment and a full restraint system for driver and front seat passenger which can be used in full scale crash testing. Furthermore, the crash trolley should have a suspension to show rotation and nick effects similar to real vehicles. Within the development phase the reference vehicle was build based on a European family car. Special attention was needed to provide appropriate strength to the trolley and its suspension. The reference vehicle is equipped with a restraint system consisting of airbags, pedals, seats, dashboard, and windscreen. On the front of the vehicle different crash barriers can be installed to provide miscellaneous deceleration pulses. For the validation phase a series of low and high speed crash tests with HIII dummies were conducted and compared with full scale tests. For the comparison deceleration pulse, dummy numbers and vehicle movement were analyzed. Validation tests with velocities up to 60 km/h showed promising results. The compartment and the suspension systems stayed stable. Rotation effects were comparable with full scale car crash tests. The airbags and seat belt system worked reasonable. The acceleration pulse compared to an Euro NCAP test had a similar characteristic but was in general slightly lower. After the successful validation the reference vehicle is already in use in different studies in the field of vehicle safety research at BASt.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
In der Europäischen Gemeinschaft werden derzeit jährlich ca. 50.000 Menschen bei Verkehrsunfällen getötet, ca. 10.000 davon als Fußgänger. Von den 10.600 (1992) in der Bundesrepublik Deutschland bei Straßenverkehrsunfällen Getöteten waren 1.800 Fußgänger (etwa 17 Prozent). Problemgruppen bei Fußgängerunfällen bilden die Kinder wegen ihrer hohen Unfallhäufigkeit und alte Personen wegen ihrer hohen Unfallschwere. Kopfverletzungen sind die häufigste Todesursache bei Fußgängerunfällen. Eine Verringerung der Unfallschwere kann - außer durch Verminderung von Fahr- beziehungsweise Aufprallgeschwindigkeiten der Fahrzeuge - nur durch konstruktive Eingriffe an der vorderen Fahrzeugaußenkontur oder dem Unterbau von Pkw erfolgen. Dazu ist es notwendig, einheitliche Prüfverfahren für die Beurteilung der "Fahrzeugaggressivität" gegenüber Fußgängern bereitzustellen. Die Ableitung eines Prüfvorschlages zur Simulation des Kopfaufpralls auf Fronthauben von Pkw beim Fußgängerunfall, unterteilt in Kopfaufpralltests für Erwachsene und Kinder, ist Gegenstand dieser Arbeit. Es werden, ausgehend von einer Analyse der Unfallstatistik, der Entstehungsmechanismus von Kopfverletzungen erklärt, die für ein Prüfverfahren notwendigen Eingangsparameter (Masse, Geschwindigkeit, Aufprallstellen am Fahrzeug etc.) abgeleitet und die Ergebnisse der gewählten Prüfkörpertestmethode mit Ergebnissen von Leichenversuchen verglichen. Eine Kosten-/Nutzen-Betrachtung am Schluss der Arbeit zeigt, dass sich bei nur geringen Kosten ein volkswirtschaftlicher Nutzen durch eine allgemeine Anwendung des Prüfverfahrens mit ca. 270 Millionen DM allein in der Bundesrepublik Deutschland pro Jahr erzielen ließe.
Die Reduzierung des Verkehrslärms ist eine große Herausforderung für alle Beteiligten. Das gilt umso mehr, als nach den Prognosen sich die Verkehrsleistung auf der Straße noch stark erhöhen wird. Viele Stellen in Deutschland, wie Industrie, Forschungseinrichtungen und Behörden haben sich der Problematik angenommen. Forschungsarbeiten wurden und werden durchgeführt oder sind in Vorbereitung. Über die nationalen Aktivitäten hinaus wird das Thema europaweit behandelt. In vier Beiträgen wird über die europäischen Forschungsprojekte SILVIA, ITARI, SILENCE und P2RN berichtet. Das Spektrum der Konzepte dieser Forschungsarbeiten ist sehr breit und erstreckt sich über praktische und theoretische Ansätze.
Cost benefit analysis
(2014)
Although the number of road accident casualties in Europe is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities [EC 2012]. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car- safety performance in frontal impacts is to improve its compatibility for car-to-car impacts and for collisions against objects and HGVs. Compatibility consists of improving both a car- self and partner protection in a manner such that there is good interaction with the collision partner and the impact energy is absorbed in the car- frontal structures in a controlled way which results in a reduction of injuries. Over the last ten years much research has been performed which has found that there are four main factors related to a car- compatibility [Edwards 2003, Edwards 2007]. These are structural interaction potential, frontal force matching, compartment strength and the compartment deceleration pulse and related restraint system performance. The objective of the FIMCAR FP7 EC-project was to develop an assessment approach suitable for regulatory application to control a car- frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.
The levels of continuous vehicle automation have become common knowledge. They facilitate overall understanding of the issue. Yet, continuous vehicle automation described therein does not cover "automated driving" as a whole: Functions intervening temporarily in accident-prone situations can obviously not be classified by means of continuous levels. Continuous automation describes the shift in workload from purely human driven vehicles to full automation. Duties of the driver are assigned to the machine as automation levels rise. Emergency braking, e.g., is obviously discontinuous and intensive automation. It cannot be classified under this regime. The resulting absence of visibility of these important functions cannot satisfy " especially in the light of effect they take on traffic safety. Therefore, in order to reach a full picture of vehicle automation, a comprehensive approach is proposed that can map out different characteristics as "Principle of Operation" at top level. On this basis informing and warning functions as well as functions intervening only temporarily in near-accident situations can be described. To reach a complete picture, levels for the discontinuous, temporarily intervening functions are proposed " meant to be the counterpart of the continuous levels already in place. This results in a detailed and independent classification for accident-prone situations. This finally provides for the visibility these important functions deserve.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
The presence and performance of Advanced Driver Assistance Systems (ADAS) has increased over last years. Systems available on the market address also conflicts with vulnerable road users (VRUs) such as pedestrians and cyclists. Within the European project PROSPECT (Horizon2020, funded by the EC) improved VRU ADAS systems are developed and tested. However, before determining systems" properties and starting testing, an up-to-date analysis of VRU crashes was needed in order to derive the most important Use Cases (detailed crash descriptions) the systems should address. Besides the identified Accident Scenarios (basic crash descriptions), this paper describes in short the method of deriving the Use Cases for car-to-cyclist crashes. Method Crashes involving one passenger car and one cyclist were investigated in several European crash databases looking for all injury severity levels (slight, severe and fatal). These data sources included European statistics from CARE, data on national level from Germany, Sweden and Hungary as well as detailed accident information from these three countries using GIDAS, the Volvo Cars Cyclist Accident database and Hungarian in-depth accident data, respectively. The most frequent accident scenarios were studied and Use Cases were derived considering the key aspects of these crash situations (e.g., view orientation of the cyclist and the car driver- manoeuvre intention) and thus, form an appropriate basis for the development of Test Scenarios. Results Latest information on car-to-cyclist crashes in Europe was compiled including details on the related crash configurations, driving directions, outcome in terms of injury severity, accident location, other environmental aspects and driver responsibilities. The majority of car-to-cyclist crashes occurred during daylight and in clear weather conditions. Car-to-cyclist crashes in which the vehicle was traveling straight and the cyclist is moving in line with the traffic were found to result in the greatest number of fatalities. Considering also slightly and seriously injured cyclists led to a different order of crash patterns according to the three considered European countries. Finally the paper introduced the Use Cases derived from the crash data analysis. A total of 29 Use Cases were derived considering the group of seriously or fatally injured cyclists and 35 Use Cases were derived considering the group of slightly, seriously or fatally injured cyclists. The highest ranked Use Case describes the collision between a car turning to the nearside and a cyclist riding on a bicycle lane against the usual driving direction. A unified European dataset on car-to-cyclist crash scenarios is not available as the data available in CARE is limited, hence national datasets had to be used for the study and further work will be required to extrapolate the results to a European level. Due to the large number of Use Cases, the paper shows only highest ranked ones.
Die vorliegende Studie untersucht die Auswirkung der Ausstattung von Motorrädern mit Anti-Blockier-System (ABS) auf die Fahrsicherheit von Motorrädern. Hierzu wurden Fahrversuche im realen Verkehr und auf abgesperrter Teststrecke durchgeführt. Erfahrene und wenig erfahrene Motorradfahrer absolvierten Testfahrten auf nasser und trockener Fahrbahn mit und ohne ABS-Aktivierung des Motorrades. Bei den Versuchsfahrten kam es zu einigen kritischen Fahrsituationen, bei denen die Versuchspersonen insbesondere zu Beginn des Bremsmanövers von ihrem "normalen" Bremsverhalten abwichen. Bei blockierendem Hinterrad wurde der Bremsdruck vorne und hinten reduziert, was zu einer deutlichen Bremswegverlängerung führte. Bei den Vollbremsungen unter idealen Bedingungen auf abgesperrter Strecke wurden von erfahrenen Fahrern ohne ABS kürzere Bremswege als mit ABS erreicht. Kurvenbremsungen mit ABS-Regelung wurden im mittleren Geschwindigkeits- und Schräglagebereich fahrstabil durchgeführt. Die Ergebnisse zeigen, dass selbst erfahrene Motorradfahrer Bremsweg in kritischen Situationen verschenken. Geeignete Antiblockiersysteme könnten Motorradfahrern die Angst vor Radblockaden nehmen. Dies dürfte einen erheblichen Beitrag zur Steigerung der aktiven Sicherheit leisten.
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
Regarding to the German road traffic licensing regulations it is mandatory to have a light system using a bicycle in public traffic. All attached components must be approved. The admission requires additional restrictions such as a dynamo as energy source with a nominal voltage of 6 V. Batteries are only allowed in addition to this. To adopt the German bicycle regulation to the state of art of an energy efficient lighting, additional power sources such as a battery respectively rechargeable batterie should be evaluated. The project will propose amendments for German Road Traffic Regulations and technical requirements.
Erfahrungen in Deutschland mit der Anwendung der EU-Empfehlung "Europäischer Grundsatzkatalog zur Fahrer-Fahrzeug-Schnittstelle für Informations- und Kommunikationssysteme" werden beschrieben und daraus Konsequenzen abgeleitet. Insgesamt ist die ergonomische Bewertung der Mensch-Maschine-Schnittstelle von Fahrerinformations- und -Kommunikationssystemen nicht als einmaliges Ereignis, sondern als immer wieder zu durchlaufender Vorgang anzusehen, da neben neuen wissenschaftlichen Erkenntnissen jeweils neu entwickelte Geräte und Systeme zu berücksichtigen sind, was eine Anpassung der Grundsätze beziehungsweise eine Öffnung der Grundsätze für technische Neuerungen mit hohem Sicherheitsstandard erfordern könnte. Demonstrationen neuartiger Bedienkonzepte, Systementwicklungen und Arbeitstechniken sowie die hierzu durchgeführten Nutzertests verdeutlichen, dass ergonomisch sehr vielversprechende Lösungen (wie zum Beispiel Schnittstellen, die Eingaben mittels Gestik gestatten) existieren, beziehungsweise sich in der Entwicklung befinden. Diese Lösungen zeigen, dass die Empfehlung in weiten Bereichen technologieabhängig, das heißt, mit Blick auf Neuentwicklungen, nicht erschöpfend ist. Die Weiterentwicklung der Grundsätze sowie die Bewertung der sicheren Gestaltung der Mensch-Maschine-Schnittstelle bedarf nicht nur einer europaweit, sondern weltweit abgestimmten Vorgehensweise.
Der Autor berichtet über das neu eingerichtete Expertennetzwerk HUMANIST, das sich mit Fragen der nutzerorientierten und sicherheitsgerechten Gestaltung von Fahrerassistenz- und Informationssystemen befasst. Ziel sind die Zusammenführung und Integration entsprechender Forschungsaktivitäten auf europäischer Ebene.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
Anforderungen, Zielkonflikte
(2019)
Um Sicherheit und Umweltverträglichkeit von Straßen- bzw. Kraftfahrzeugen zu gewährleisten, werden an die Gestaltung der Fahrzeuge technische Anforderungen gestellt. Es gibt Anforderungen durch den Gesetzgeber, die erfüllt werden müssen, um ein Fahrzeug in den Verkehr bringen zu dürfen. Darüber hinaus bestehen herstellerinterne Anforderungen an das Produkt, die über das vom Gesetzgeber geforderte Maß hinausgehen, um den Kundenwünschen und der Firmenphilosophie zu genügen. Und als dritter Punkt stellen auch Verbraucherschutz-Organisationen Kriterien auf, anhand derer sie die Eigenschaften der auf dem Markt befindlichen Fahrzeuge bewerten und die Fahrzeuge eingruppieren, was dann der Kundeninformation dient. Auch diese Anforderungen gehen über die des Gesetzgebers hinaus. Das Setzen der gesetzlichen Mindestanforderungen ist für die Fahrzeugtechnik mittlerweile jedoch nicht mehr einzelnen Staaten überlassen. Vielmehr sind die für die Genehmigung von Fahrzeugtypen einzuhaltenden Bedingungen international harmonisiert: Für die EU sind dies EU-Richtlinien oder EU-Verordnungen, die von der Europäischen Kommission in Brüssel vorgeschlagen werden. Für über die EU hinausgehende Staaten bzw. Regionen sind dies unter anderem Regelungen der UN, erstellt von der UN-Wirtschaftskommission für Europa (UNECE) in Genf.