91 Fahrzeugkonstruktion
Im Rahmen des weltweiten ESV-Programmes (Enhanced Safety of Vehicles) werden seit mehreren Jahren internationale Forschungsbemühungen unternommen (International Harmonized Research Activities, IHRA), um im Vorfeld der Gesetzgebung die wissenschaftlichen Grundlagen gemeinsam zu erarbeiten. Ziel der IHRA-Arbeiten ist es, auf der Grundlage dieser Forschungsergebnisse die Harmonisierung der Vorschriften zu erleichtern. Eine besondere Aktivität bezieht sich auf Intelligent Transportation Systems (ITS). Im vorliegenden Beitrag wird die Aufgabe dieser IHRA-ITS-Arbeiten geschildert, sowie der derzeitige Stand der Forschungsbemühungen beschrieben. Es zeigt sich, dass die beschriebene Sicherheitsbewertung eine Fülle von Fragestellungen aufwirft und weitere Forschungsanstrengungen erfordert. Die zukünftigen Bemühungen sind darauf gerichtet, in internationaler Zusammenarbeit und Arbeitsteilung die als besonders wichtig erkannten Themen zur Bewertung der fahrzeugseitigen Fahrerassistenzsysteme zu bearbeiten.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
This study is aimed to investigate the correlations of impact conditions and dynamic responses with the injuries and injury severity of child pedestrians by accident reconstruction. For this purpose, the pedestrian accident cases were selected from Sweden and Germany with detailed information about injuries, accident cars, and accident environment. The selected accident cases were reconstructed using mathematical models of pedestrian and passenger car. The pedestrian models were generated based on the height, weight, and age of the pedestrian involved in accidents. The car models were built up based on the corresponding accident car. The impact speeds in simulations were defined based on the reported data. The calculated physical quantities were analyzed to find the correlation with injury outcomes registered in the accident database. The reconstruction approaches are discussed in terms of data collection, estimating vehicle impact speeds, pedestrian moving speeds and initial posture, secondary ground impact, validity of the mathematical models, as well as impact biomechanics.
Schutz von schwächeren Verkehrsteilnehmern: kommende Anforderungen aus Gesetzgebung und Euro NCAP
(2017)
Systeme der aktiven Fahrzeugsicherheit, insbesondere Notbremsassistenzsysteme und automatische Notbremssysteme, haben in den letzten zwei Dekaden große technische Fortschritte gemacht, und das im Wesentlichen ohne "Druck" von Gesetzgeber oder unabhängigen Testorganisationen " diese können aber durch passende Anforderungen den Vormarsch der Systeme in die Breite und die Ausnutzung von ansonsten für den Hersteller vielleicht nicht wirtschaftlichen Potentialen unterstützen. Dieser Bericht hat das Ziel, einen Überblick über die kommenden Anforderungen an Schutzsysteme für schwächere Verkehrsteilnehmer zu geben und diese Anforderungen in den Kontext Euro NCAP (=welchen Einfluss haben diese Anforderungen auf die Gesamtbewertung?) sowie Gesetzgebung (schwächere Anforderungen, aber dafür ein Markteintrittskriterium) zu stellen: - Anforderungen und Testprozeduren für Notbremsassistenz Fahrradunfälle 2018 und 2020 in Euro NCAP; - Anforderungen und Testprozeduren für Notbremsassistenz bei Nachtunfällen mit Fußgängern in Euro NCAP 2018; - Anforderungen und Testprozeduren für Abbiegeassistenzsysteme zum Schutz von Radfahrern in Unfallsituationen mit rechtsabbiegenden Lkw innerhalb der Fahrzeugtypgenehmigung.
Neben der zunehmenden Bedeutung der aktiven Sicherheit bleiben Maßnahmen der passiven Sicherheit bei der Entwicklung moderner Kraftfahrzeuge unabdingbar. Die Weiterentwicklung von Maßnahmen zum passiven Fußgängerschutz war zunächst größtenteils durch Verbraucherschutztests wie zum Beispiel Euro NCAP oder JNCAP getrieben und ist nun auch durch gesetzliche Regelungen verpflichtend geworden. Im vorangegangenen Forschungsprojekt der BASt FE 82.229/2002 Schutz von Fußgängern beim Scheibenaufprall ist die Grundlage eines modularen Prüfverfahrens für den Kopfaufprall im Bereich der Windschutzscheibe, bestehend aus einem Versuchs- und einem Simulationsteil, erarbeitet worden. Im Rahmen dieses Projektes wurde ein hybrides Testverfahren bestehend aus Versuch und Simulation ausgearbeitet, das den Bereich der Windschutzscheibe und dabei auch crashaktive Systeme wie Airbags berücksichtigt. Das Testverfahren kombiniert Komponentenversuche mit einem Simulationsteil, in dem Fahrzeug-Fußgänger-Simulationen und lmpaktorsimulationen durchgeführt werden. Zusätzliche Dummyversuche dienten zur Bewertung des Testverfahrens. Alle erarbeiteten virtuellen und realen Testmethoden wurden an einem Referenzfahrzeug (Opel Signum), welches repräsentativ für eine durchschnittliche Mittelklasselimousine steht, durchgeführt. Das Fahrzeug wurde mit einem Airbagsystem ausgerüstet und der Testprozedur mit und ohne diesem System vergleichend unterzogen. Innerhalb dieser Untersuchungen konnte gezeigt werden, dass neue Testmethoden unter Ausnutzung von Simulationen und Komponententests es erlauben, realistischere Versuchsbedingungen unter Berücksichtigung von potenziellen Kopfaufprallpositionen und -zeiten zu definieren. Dabei können sehr gute Übereinstimmungen zwischen Fußgängersimulation und Dummyversuch erreicht werden. Die Randbedingungen für den Kopfaufprall und die Aufprallzeit wurden durch den Einsatz von Fußgängermodellen ermittelt. Weiterhin ermöglichen die Simulationen, zusätzliche Einflussdaten wie Vektoren mit den Kopfaufprallgeschwindigkeiten und -winkeln zu bestimmen.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Test and assessment procedures for passive pedestrian protection based on developments by the European Enhanced Vehicle-safety Committee (EEVC) have been introduced in world-wide regulations and consumer test programmes, with considerable harmonization between these programmes. Nevertheless, latest accident investigations reveal a stagnation of pedestrian fatality numbers on European roads running the risk of not meeting the European Union- goal of halving the number of road fatalities by the year 2020. The branch of external road user safety within the EC-funded research project SENIORS under the HORIZON 2020 framework programme focuses on investigating the benefit of modifications to pedestrian test and assessment procedures and their impactors for vulnerable road users with focus on the elderly. Injury patterns of pedestrians and cyclists derived from the German In-Depth Accident Study (GIDAS) show a trend of AIS 2+ and AIS 3+ injuries getting more relevant for the thorax region in crashes with newer cars (Wisch et al., 2017), while maintaining the relevance for head and lower extremities. Several crash databases from Europe such as GIDAS and the Swedish Traffic Accident Data Acquisition (STRADA) also show that head, thorax and lower extremities are the key affected body regions not only for the average population but in particular for the elderly. Therefore, the SENIORS project is focusing on an improvement of currently available impactors and procedures in terms of biofidelity and injury assessment ability towards a better protection of the affected body regions, incorporating previous results from FP 6 project APROSYS and subsequent studies carried out by BASt. The paper describes the overall methodology to develop revised FE impactor models. Matched human body model and impactor simulations against generic test rigs provide transfer functions that will be used for the derivation of impactor criteria from human injury risk functions for the affected body regions. In a later step, the refined impactors will be validated by simulations against actual vehicle front-ends. Prototyping and adaptation of test and assessment procedures as well as an impact assessment will conclude the work of the project at the final stage. The work will contribute to an improved protection of vulnerable road users focusing on the elderly. The use of advanced human body models to develop applicable assessment criteria for the revised impactors is intended to cope with the paucity of actual biomechanical data focusing on elderly pedestrians. In order to achieve optimized results in the future, the improved test methods need to be implemented within an integrated approach, combining active with passive safety measures. In order to address the developments in road accidents and injury patterns of vulnerable road users, established test and assessment procedures need to be continuously verified and, where needed, to be revised. The demographic change as well as changes in the vehicle fleet, leading to a variation of accident scenarios, injury frequencies and injury patterns of vulnerable road users are addressed by the work provided by the SENIORS project, introducing updated impactors for pedestrian test and assessment procedures.
A reduction of around 48% of all road fatalities was achieved in Europe in the past years including a reduced number of fatalities with an older age. However, among all road fatalities, the proportion of elderly is steadily increasing. In an ageing society, the European (Horizon2020) project SENIORS aims to improve the safe mobility of older road users, who have different transportation habits compared to other age groups. To increase their level of safe mobility by determining appropriate requirements for vehicle safety systems, the characteristics of current road traffic collisions involving the elderly and the injuries that they sustain need to be understood in detail. Hereby, the paper focuses on their traffic participation as pedestrian, cyclist or passenger car occupant. Following a literature review, several national and international crash databases and hospital statistics have been analysed to determine the body regions most frequently and severely injured, specific injuries sustained and types of crashes involved, always comparing older road users (65 years and more) with mid-aged road users (25-64 years). The most important crash scenarios were highlighted. The data sources included European statistics from CARE, data on national level from Germany, Sweden, Italy, United Kingdom and Spain as well as in-depth crash information from GIDAS (Germany), RAIDS (UK), CIREN and NASS-CDS (US). In addition, familiar hospital data from Germany (TraumaRegister DGU-®), Italy (Italian Register of Acute Traumas) and UK hospital statistics (TARN) were included in the study to gain further insight into specific injury patterns. Comprehensive data analyses were performed showing injury patterns of older road users in crashes. When comparing with mid-aged road users, all databases showed that the thorax body region is of particularly high importance for the older car occupant with injury severities of AIS 2 or AIS 3+, whereas the body regions lower extremities, head and thorax need to be considered for the older pedestrians and cyclists. Besides these comparisons, the most frequent and severe top 5 injuries were highlighted per road user group. Further, the most important crash configurations were identified and injury risk functions are provided per age group and road user group. Although several databases have been analysed, the picture on the road safety situation of older road users in Europe was not complete, as only Western European data was available. The linkage between crash data and hospital data could only be made on a general level as their inclusion criteria were quite different.
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
Um die Verletztenschwere von ungeschützten Verkehrsteilnehmern bei der Kollision mit Personenkraftwagen zu reduzieren, sollte die Fahrzeugfront bestimmten Anforderungen entsprechen. Dazu wurde von der EEVC-WG 10 ein Testverfahren zur Prüfung der Pkw-Frontfläche vorgeschlagen. In dieser Untersuchung wurde der Nutzen an vermeidbaren Personenschäden geschätzt, der erzielt werden könnte, wenn alle Pkw diese Anforderungen erfüllten. Als Nutzen wurde das Reduktionspotential bei Getöteten, der mögliche Übergang von Schwerverletzten zu Leichtverletzten und von Leichtverletzten zu Unverletzten bewertet. Verletzungsminderungen innerhalb der Gesamtheit der Schwerverletzten konnten nicht bewertet werden. Auch die hohe Dunkelziffer der Verletzten ging nicht in die Rechnung ein. Daraus ergibt sich, dass der errechnete Nutzen eine Mindestgröße darstellt. Diese Größe wird stark beeinflusst von einer gegebenen Verteilung der Pkw-Kollisionsgeschwindigkeiten, denn ein Nutzenpotential des EEVC-WG-10-Testverfahrens kann nur für Kollisionsgeschwindigkeiten bis 40 km/h angenommen werden. Um mit einer verlässlichen Datenbasis zu arbeiten, wurde diese Untersuchung zunächst für die Bundesrepublik Deutschland (Gebietsstand vor dem 3. Oktober 1990) und das Jahr 1990 durchgeführt. Dafür errechnete sich ein Nutzenpotential pro neuzugelassenem Pkw in Höhe von 46 bis 63 DM (22 bis 31 ECU) nach deutschen Unfallkostensätzen oder 28 bis 36 ECU nach europäischen Durchschnittskostensätzen. Wirtschaftlich ist die Maßnahme, solange die Kosten pro neu zugelassenem Pkw (zum Preisstand 1990) diesen Betrag nicht übersteigen. Von diesem Ergebnis ausgehend, wurde dessen zeitliche und regionale Übertragbarkeit erörtert. Es ist wahrscheinlich, dass das Ergebnis für ganz Deutschland gilt, da die Maßnahme nicht vor dem Jahr 2000 eingeführt wird und die Vollausrüstung aller Pkw mit dem geforderten Fußgängerschutz erst 10 Jahre später erreicht ist. Aus Prognosen bis zum Jahre 2010 für die Entwicklung der Bevölkerungszahl (gleichbleibender Fußgängeranteil vorausgesetzt) und der Zahl der Pkw-Neuzulassungen lässt sich keine Änderung des Nutzenpotentials herleiten. Weil für andere EG-Länder die Verteilung der Kollisionsgeschwindigkeiten bei Fußgängerunfällen unbekannt ist, können die Wirksamkeitsannahmen dieser Untersuchung nicht auf andere Länder übertragen werden.
Injury probability functions for pedestrians and bicyclists based on real-world accident data
(2017)
The paper is focusing on the modelling of injury severity probabilities, often called as Injury Risk Functions (IRF). These are mathematical functions describing the probability for a defined population and for possible explanatory factors (variables) to sustain a certain injury severity. Injury risk functions are becoming more and more important as basis for the assessment of automotive safety systems. They contribute to the understanding of injury mechanisms, (prospective) evaluation of safety systems and definition of protection criteria or are used within regulation and/or consumer ratings. In all cases, knowledge about the correlation between mechanical behavior and injury severity is needed. IRFs are often based on biomechanical data. This paper is focusing on the derivation of injury probability models from real world accident data of the GIDAS database (German In-depth Accident Study). In contrast to most academic terms there is no explicit term definition or definition of creation processes existing for injury probability models based on empirical data. Different approaches are existing for such kind of models in the field of accident research. There is a need for harmonization in terms of the used methods and data as well as the handling with the existing challenges. These are preparation of the dataset, model assumptions, censored/unknown data, evaluation of model accuracy, definition of dependent and independent variable, and others. In the presented study, several empirical, statistical and phenomenological approaches were analyzed regarding their advantages and disadvantages and also their applicability. Furthermore, the identification of appropriate prediction parameters for the injury severity of pedestrians has been considered. Due to its main effect on injuries of pedestrians and bicyclists, the importance of the secondary impact has also been analyzed. Finally, the model accuracy, evaluated by several criteria, is the rating factor that gives the quality and reliability for application of the resulting models. After the investigation and evaluation of statistical approaches one method was chosen and appropriate prediction variables were examined. Finally, all findings were summarized and injury risk functions for pedestrians in real world accidents were created. Additionally, the paper gives instructions for the interpretation and usage of such functions. The presented results include IRFs for several injury severity levels and age groups. The presented models are based on a high amount of real world accidents and describe very well the injury severity probability of pedestrians and bicyclists in frontal collisions with current vehicles. The functions can serve as basis for the evaluation of effectiveness of systems like Pedestrian-AEB or Bicycle-AEB.
In-depth road traffic accident research in Spain is a fairly recent activity. In the past, only accident data that had been retrospectively processed by the national and regional traffic police forces was available. In 1999 Applus+IDIADA set up a permanent accident research unit to carry out indepth analysis of road accidents in Spain. Since then accidents involving cars, motorcycles, coaches and vulnerable road users have been thoroughly studied. The Applus+IDIADA accident research team has carried out work for the various traffic polices in Spain and it is currently involved in several research projects in which accidentology is one of the main tasks. The working methodology of the team is presented in the first part of the paper. In the framework of the European research project "Rollover" (GRD2-2001-50086), Applus+IDIADA has collected data, inspected scenarios and performed virtual reconstructions of twenty-six of the total seventy-six rollover accidents studied. The second half of the paper describes how these accident investigations were used to develop a test procedure for identifying possible improvements to the vehicle structure which augment occupant protection in a rollover scenario. In particular, a proposal for a new drop test for rollover assessment is presented. The cases were analysed for severity, in terms of injury to the occupants and damage to the vehicle, and taking into account whether a seatbelt was worn or not. The worst possible cases were identified as those that had severe occupant injuries and sizable damage to the occupant compartment when seatbelts had been worn. The most severe cases were then analysed further for impact position (roll and pitch angles) and the impact velocity. With these parameters taken into account, the most representative combinations could be found. This resulted in a series of configurations for possible drop tests. The results of the tests indicate where passenger vehicle structures need to be improved in order to increase occupant safety in the event of a rollover crash.
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
Zu den gefährlichsten Situationen im Straßenverkehr gehört der Konflikt zwischen einem Lkw und einem ungeschützten Verkehrsteilnehmer UVT (Radfahrer und Fußgänger). In Deutschland ereignen sich jährlich schätzungsweise 135 Unfälle mit Personenschaden, an denen nach rechts abbiegende Lkw (>3,5 t) und UVT beteiligt sind. Die UVT geraten dabei oft unter den Lkw und werden dann von einer der Achsen überrollt. Aus der Unfallanalyse ergab sich, dass der Erstkontakt häufig (57%) im Bereich der rechten vorderen Lkw-Ecke erfolgt. Die Hälfte der UVT gerieten noch vor oder im unmittelbaren Bereich des rechten Vorderrads unter den Lkw. Baustellen- und Kommunalfahrzeuge waren mit 46% häufig an den Unfällen beteiligt. Das direkte und das indirekte Sichtfeld sind zentrale Einflussgrößen für die Situation des rechts abbiegenden Lkw. Besonders die unzureichende Sicht nach vorn und nach rechts bereitet den Lkw-Fahrern erhebliche Probleme. An der Verbesserung der Information über die Verkehrssituation für den Lkw-Fahrer wird vielfach gearbeitet. Einzelne Lösungsansätze basieren auf dem Einsatz zusätzlicher Spiegel. Andere Lösungen modifizieren die bislang übliche Spiegelzahl in Form und Anbringung. Das Versuchsprogramm umfasste neben der Nachbildung der besonders häufigen und kritischen Situationen der rechts abbiegenden Lkw mit UVT-Dummies auch statische Untersuchungen des Sichtfeldes. Neben einem Lkw mit Standardspiegeln kam dabei ein Forschungsträger mit einem durch die Frontscheibe einsehbaren Spiegelsystem zum Einsatz. Das Projekt setzte sich auch mit der Wirkung des Seitenschutzes auseinander. Die bislang als Bauvorschrift wirkende Richtlinie 89/297/EWG sollte zukünftig zu einer Wirkvorschrift unter Einbeziehung des Pkw - Anpralls geändert werden. Das im Rahmen des Projektes erstellte Sicherheitskonzept beinhaltet Maßnahmen zur Reduzierung des Gefahrenpotenzials für UVT durch rechts abbiegende Lkw. Dazu gehören unter anderem abgesenkte Unterkanten der Front- und Seitenscheiben und zusätzliche Kamera-Monitor-Systeme. Das neuartige Spiegelsystem des MIM-Fahrzeugs von DC verbessert die indirekte Sicht für den Lkw-Fahrer deutlich und reduziert damit die Unfallgefahr. Die in der Entwicklung befindlichen Abbiegeassistenten zeigen die zukünftige Richtung für elektronische Fahrerunterstützung (MAN Demonstrator) auf. Ein beim Rechtsabbiegen aktivierter akustischer Signalgeber am Lkw wäre zur Information der UVT hilfreich. Eine weitere Option besteht in der Nutzung der seitlichen Markierungsleuchten des Lkws als zusätzliche Fahrtrichtungsanzeiger beim Abbiegen. Fahrbahn-Knotenpunkte können noch sicherer gestaltet werden. An ampelgeregelten Knotenpunkten würde eine vollständige Phasentrennung des Grünlichts oder ein Phasenverzug (früheres Grünlicht für UVT) Unfälle zwischen Lkw und UVT vermeiden. Weiterhin wirken sich eine versetzte Anordnung der Haltelinien und ein Verschwenken der Radfahrwege und Gehwege weg vom Knotenmittelpunkt positiv aus. Der Gesetzgeber sollte -§ 5 (8) StVO ändern, der des Radfahrern und Mofafahrern erlaubt, stehende Kraftfahrzeuge rechts zu überholen. 10% der untersuchten Abbiegeunfälle sind in dieser Situation passiert. Aufklärungsarbeit bezüglich der Sichtprobleme am Lkw sowie über das Bewegungsverhalten beim Rechtsabbiegen ist dringend erforderlich. Es ist auch zu überlegen, ob Aktivitäten von Herstellern beziehungsweise Unternehmern anerkannt werden, die mehr tun als die gesetzlichen Vorschriften verlangen, zu einer Lockerung vorhandener Restriktionen führen können. Es gibt in innerstädtischen Bereichen für einige Fußgängerzonen vorgesehene Zeitfenster zur Anlieferung von Gütern. Solche Zeitfenster könnten für mit anerkannten zusätzlichen Sicherheitseinrichtungen ausgerüstete Lkw ausgedehnt werden. Schwere Lkw aus bestimmten innerörtlichen Bereichen möglichst herauszuhalten, um UVT zu schützen, ist nicht praktikabel. Selbst wenn es gelänge, für die Belieferung mit Post und Waren akzeptable Alternativen zu bieten, bliebe nach wie vor der Baustellenverkehr und die kommunale Entsorgung. An 46% der untersuchten Unfälle waren derartige Lkw beteiligt.
Der Anteil von Geländefahrzeugen an der Gesamtzahl von Personenkraftwagen betrug im Juli 1991 in den alten Bundesländern ca. 1,1 Prozent. Nach eigenen Erhebungen sind etwa 62 Prozent der Geländefahrzeuge mit einem Frontschutzbügel ausgestattet. Der Bundesminister für Verkehr hat die BASt beauftragt zu prüfen, ob solche Konstruktionen einen Einfluss auf die Verletzungen bei Kollisionen mit Fußgängern und Zweiradbenutzern haben. Dazu wurde das Datenmaterial der Unfallerhebung der Medizinischen Hochschule Hannover ausgewertet und die um fahrzeugtechnische Angaben ergänzten Unfalldaten aus Nordrhein-Westfalen betrachtet. Weiterhin wird von Komponententests berichtet, die den Anprall menschlicher Körperteile an das Fahrzeug simulieren. Mit den Ergebnissen dieser Untersuchung wurde ein Frontschutzbügel hergestellt, der weniger aggressiv gegenüber ungeschützten Verkehrsteilnehmern ist. Zur Quantifizierung der Gefährdung von Fußgängern wurden zwei gängige Geländefahrzeugtypen mit und ohne Frontschutzbügel gemäß dem Prüfvorschlag der EEVC-WG 10 zur Bestimmung der Fußgängerverträglichkeit von Pkw-Frontflächen getestet. Die Ergebnisse aus den Versuchsreihen wurden mit Ergebnissen aus Versuchen an normalen Pkw verglichen.Es kann festgestellt werden, dass bei einem Unfall mit Kopfanprall eines Kindes an ein mit Frontschutzbügel ausgestattetes Geländefahrzeug bei 20 km/h mit gleichen Kopfbelastungen zu rechnen ist, wie bei einem Unfall mit 30 km/h mit einem Geländefahrzeug ohne Frontschutzbügel, beziehungsweise mit 40 km/h mit einem normalen Pkw. Für den Hüftanprall eines Erwachsenen an die Haubenkante ist bei einer Fahrzeuggeschwindigkeit von 25 km/h bei einem Fahrzeug mit Frontschutzbügel mit gleichen Belastungen zu rechnen, wie bei einem Unfall mit einem Fahrzeug ohne Frontschutzbügel bei 40 km/h (Pkw oder Geländewagen). Für die Belastungen des Knies eines Erwachsenen lässt sich keine Verschlechterung durch montierte Frontschutzbügel ableiten.
Beschrieben wird die Evaluierung eines Testverfahrens der Arbeitsgruppe 10 des European Experimental Vehicle Committee, mit dem die "Fußgängerverträglichkeit" von Frontflächen von Personenkraftwagen bestimmt werden kann. Dabei werden verschiedene Anprallarten von Fußgängern an Fahrzeugen simuliert: der Anprall eines Beines an den Stoßfänger, der Anprall des Oberschenkels an die Vorderkante der Fronthaube und der Anprall des Kopfes auf die Fronthaube. Im Beitrag wird auf die Durchführung von Tests zum Oberschenkelanprall und zum Beinanprall an drei verschiedenen Fahrzeugtypen eingegangen. Beschrieben werden Testverfahren, Versuchsaufbau und Versuchsdurchführung. Die Versuchsreihe zeigte, dass das entwickelte Testverfahren praktikabel ist.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
Seit 1997 gibt es in Europa unter dem Namen Euro NCAP (European New Car Assessment Programme) einheitliche Test- und Ratingverfahren. Sie liefern Informationen über den Insassen- und über den Fußgängerschutz. Euro NCAP hat seither fast 90 Fahrzeugmodelle in jeweils drei unterschiedlichen Crashtest-Konfigurationen untersucht und die Ergebnisse den europäischen Konsumenten zugänglich gemacht. Im Beitrag wird auf die Testbedingungen, die Euro NCAP-Ratingverfahren sowie auf die Weiterentwicklung von Euro NCAP eingegangen. Ein wichtiger Aspekt wird dabei auch die weltweite Harmonisierung der Test- und Ratingverfahren sein.
Es ist zu beobachten, dass trotz einer Abnahme der Zahl der Verletzungen und der Verletzungsschwere der Insassen bei Pkw-Unfällen Halswirbelsäulen (HWS)-Distorsionen, speziell im unteren Geschwindigkeitsbereich häufiger auftreten. Neben anderen Faktoren werden auch veränderte Beschleunigungs- und Verzögerungsimpulse, die im Crashfall auf die Insassen wirken, als möglicherweise ursächlich für die Entstehung von HWS-Distorsionen angesehen. In der vorliegenden Arbeit wird untersucht, welchen Einfluss konstruktive Veränderungen, die durch Versicherungseinstufungstests bedingt werden, auf die Beschleunigungs- und Verzögerungsimpulse im Fahrzeuginnenraum haben. Versuche zum Fußgängerschutz wurden einvernehmlich nicht durchgeführt, da die Fahrzeuge noch nicht konsequent nach Fußgängerschutzkriterien konzipiert werden. Die Untersuchungsmethode lässt sich gliedern in: - Analyse von internationalen Versicherungssystemen und Analyse der aus den Versicherungseinstufungstests resultierenden Veränderungen von Fahrzeugstrukturen; - Durchführung und Analyse von eigenen Aufprallversuchen mit Fahrzeugteilstrukturen und vergleichende Analyse von Vollfahrzeugversuchen der Versicherungswirtschaft; Zusammenführen der getätigten Schritte. Bei der Ersteinstufung eines Pkw in die Vollversicherung dient der Versicherungseinstufungstest des RCAR/AZT (Prüfgeschwindigkeit 15 km/h) zur Bestimmung der Schadenshöhe und damit zur Einstufung in eine Typklasse. In vielen weiteren Staaten dienen dieser oder ähnliche Tests zur Bewertung der Reparaturfreundlichkeit von Pkw. Um bei einem Versicherungseinstufungstest den Schaden möglichst gering zu halten, haben nahezu alle Neufahrzeuge Querträgersysteme mit kostenarm wechselbaren Absorptionselementen, die die Crashenergie gezielt auf kurzem Weg aufnehmen. Durch die neu EG-Richtlinie 2003/102/EG zum Fußgängerschutz müssen zukünftig hinter der Stoßfängeraußenhaut und vor dem massiven Querträger weiche Schäume untergebracht werden. Der Bauraum für Querträger und Energieabsorptionselemente wird dadurch weiter eingeschränkt. Diese Anforderungen veranlassen die Hersteller dazu, die Energieabsorptionselemente steifer zu gestalten, um einen effektiven Energieabbau bei kurzen Stopplängen zu gewährleisten. Durch diese Maßnahmen wird zwar der Insassenschutz bei Frontalaufprallen im Hochgeschwindigkeitsbereich verbessert, es werden aber zugleich höhere Innenraumverzögerungen (schnellerer Anstieg, höhere mittlere Verzögerung) bei Crashs im gesamten Geschwindigkeitsbereich erzeugt. Eine durchgeführte Korrelation zwischen konstruktiven Veränderungen am Fahrzeug und empirisch bestimmten Verzögerungsverläufen zeigte, dass eine günstigere Einstufung in der Fahrzeugvollversicherung nicht zwangsläufig höhere Verzögerungsimpulse für den Innenraum bedingen muss. Bei der Analyse von 172 Crashversuchen des Allianz Zentrums für Technik mit Neufahrzeugen aus den Jahren 1992 bis 2003 zeichnen sich aber statistisch bedeutsame ßnderungen in den Verzögerungsverläufen über die Prüfjahre ab: - Anstieg der Verzögerung wird steiler; - Mittelwert der Verzögerung wird grösser; - Zeitdauer bis zum Auftreten der maximalen Verzögerung wird kürzer; - dynamische Gesamtdeformation wird kleiner. Die steife Auslegung der für den Versicherungseinstufungstest relevanten Crashteile verbessert den Insassenschutz bei Hochgeschwindigkeitscrashs. Wenn es sich aber durch weitere Untersuchungen bestätigt, dass höhere Verzögerungs- beziehungsweise Beschleunigungsimpulse die Auftretenswahrscheinlichkeit von HWS-Verletzungen im Niedriggeschwindigkeitsbereich vergrößern, so sollten gezielt Maßnahmen zur Verringerung dieser Verletzungsrisiken ergriffen werden. Dazu gehören die weitere Optimierung der Sitzstrukturen einschließlich der Kopfstützen und die Entwicklung adaptiver Crashstrukturen, die dem Crashfall angepasste Kraft-Weg-Kennlinien ermöglichen.
EEVC Status report
(2001)
In der Europäischen Union (EU) gab es 1999 circa 1,3 Millionen Straßenverkehrsunfälle mit Personenschaden, wobei circa 42.000 Personen getötet wurden. Ziel der EU ist es diese Zahl auf 25.000 im Jahr 2010 zu senken. Die EEVC befasst sich bereits seit Anfang der 80er Jahre mit der Thematik Fußgängerschutz in verschiedenen Arbeitsgruppen. Im Dezember 1998 legte die EEVC-Arbeitsgruppe 17 "Fußgängersicherheit" ihren Abschlussbericht vor, in dessen Anhang ein Prüfverfahren zum fahrzeugseitigen Fußgängerschutz enthalten ist. Dieses Prüfverfahren wird vorgestellt. Es basiert auf Komponententests. Unterschieden werden drei Prüfkörperarten und insgesamt vier Prüfkörper. Aus wissenschaftlicher Sicht und aus Sicht der Unfallforschung empfiehlt die EEVC-Arbeitsgruppe 17 eine umfassende Einführung des vorgeschlagenen Prüfverfahrens mit allen Prüfkörpern, gegebenenfalls in Form einer stufenweisen Einführung.
In der Europäischen Gemeinschaft werden derzeit jährlich ca. 50.000 Menschen bei Verkehrsunfällen getötet, ca. 10.000 davon als Fußgänger. Von den 10.600 (1992) in der Bundesrepublik Deutschland bei Straßenverkehrsunfällen Getöteten waren 1.800 Fußgänger (etwa 17 Prozent). Problemgruppen bei Fußgängerunfällen bilden die Kinder wegen ihrer hohen Unfallhäufigkeit und alte Personen wegen ihrer hohen Unfallschwere. Kopfverletzungen sind die häufigste Todesursache bei Fußgängerunfällen. Eine Verringerung der Unfallschwere kann - außer durch Verminderung von Fahr- beziehungsweise Aufprallgeschwindigkeiten der Fahrzeuge - nur durch konstruktive Eingriffe an der vorderen Fahrzeugaußenkontur oder dem Unterbau von Pkw erfolgen. Dazu ist es notwendig, einheitliche Prüfverfahren für die Beurteilung der "Fahrzeugaggressivität" gegenüber Fußgängern bereitzustellen. Die Ableitung eines Prüfvorschlages zur Simulation des Kopfaufpralls auf Fronthauben von Pkw beim Fußgängerunfall, unterteilt in Kopfaufpralltests für Erwachsene und Kinder, ist Gegenstand dieser Arbeit. Es werden, ausgehend von einer Analyse der Unfallstatistik, der Entstehungsmechanismus von Kopfverletzungen erklärt, die für ein Prüfverfahren notwendigen Eingangsparameter (Masse, Geschwindigkeit, Aufprallstellen am Fahrzeug etc.) abgeleitet und die Ergebnisse der gewählten Prüfkörpertestmethode mit Ergebnissen von Leichenversuchen verglichen. Eine Kosten-/Nutzen-Betrachtung am Schluss der Arbeit zeigt, dass sich bei nur geringen Kosten ein volkswirtschaftlicher Nutzen durch eine allgemeine Anwendung des Prüfverfahrens mit ca. 270 Millionen DM allein in der Bundesrepublik Deutschland pro Jahr erzielen ließe.
Ausgehend von den Unfalldaten der letzten Jahre wird die Bedeutung von Fußgängerunfällen im Unfallgeschehen dargestellt. Betrachtet man die bei Unfällen getöteten Verkehrsteilnehmer, so sind am häufigsten Personen in Kraftfahrzeugen betroffen. Am zweithäufigsten werden, gemäß der Unfallstatistik, Fußgänger getötet. Eine Möglichkeit zur Verbesserung des Schutzes von Fußgängern und anderen sogenannten "ungeschützten Verkehrsteilnehmern" im Falle einer Kollision mit einem Kraftfahrzeug sind Maßnahmen am Fahrzeug. Um die Wirksamkeit derartiger Maßnahmen zu beurteilen, wurde durch das EEVC (European Enhanced Vehicle-Safety Committee) ein Prüfverfahren entwickelt. Es handelt sich dabei um ein Komponentenprüfverfahren, mit dem die Frontstruktur von Fahrzeugen, die bei einer Kollision mit einem Fußgänger hauptsächlich betroffen ist, geprüft wird. Es werden keine den gesamten Menschen repräsentierende Dummies verwendet, stattdessen werden Prüfkörper, die einzelne Körperteile simulieren, eingesetzt. Dieser EEVC Vorschlag wird geschildert. Darüber hinaus wird über Aktivitäten außerhalb des EEVC berichtet, sowie über den aktuellen Stand der Bemühungen der Europäischen Kommission in Bezug auf den Fußgängerschutz, die derzeit, auf Grundlage des Prüfvorschlages des EEVC, einen Vorschlag für eine Europäische Richtlinie erarbeitet.
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
Because of actual developments and the continuous increase in the field of drive assistant systems, representative and detailed investigations of accident databases are necessary. This lecture describes the possibility to estimate the potential of primary and secondary safety measures by means of a computerized case by case analysis. Single primary or secondary safety measures as well as a combination of both are presented. The method is exemplarily shown for the primary safety measure "Brake Assist" in pedestrian accidents. Regarding accident prevention only the primary safety measure is determined.
A series of drop tests and vehicle tests with the adult head impactor according to Regulation (EC) 631/2009 and drop tests with the phantom head impactor according to UN Regulation No. 43 have been carried out by the German Federal Highway Research Institute (BASt) on behalf of the German Federal Ministry of Transport, Building and Urban Development (BMVBS). Aim of the test series was to study the injury risk for vulnerable road users, especially pedestrians, in case of being impacted by a motor vehicle in a way described within the European Regulations (EC) 78/2009 and (EC) 631/2009. Furthermore, the applicability of the phantom head drop test described in UN Regulation No. 43 for plastic glazing should be investigated. In total, 30 drop tests, thereof 18 with the adult head impactor and 12 with the phantom head impactor, and 49 vehicle tests with the adult head impactor were carried out on panes of laminated safety glass (VSG), polycarbonate (PC) and laminated polycarbonate (L-PC). The influence of parameters such as the particular material properties, test point locations, fixations, ambient conditions (temperature and impact angle) was investigated in detail. In general, higher values of the Head Injury Criterion (HIC) were observed in tests on polycarbonate glazing. As the HIC is the current criterion for the assessment of head injury risk, polycarbonate glazing has to be seen as more injurious in terms of vulnerable road user protection. In addition, the significantly higher rebound of the head observed in tests with polycarbonate glazing is suspected to lead to higher neck loads and may also cause higher injury risks in secondary impacts of vulnerable road users. However, as in all tests with PC glazing no damage of the panes was observed, the risk of skin cut injuries may be expected to be reduced significantly. The performed test series give no indication for the test procedure prescribed in UN Regulation No. 43 as a methodology to approve glass windscreen not being feasible for polycarbonate glazing, as all PC panes tested fulfilled the UN R 43 requirements. The performance of the windscreen area will not be relevant for vehicle type approval according to the upcoming UN Regulation for pedestrian protection. However, it is recommended that pedestrian protection being considered for plastic windscreens to ensure at least the same level of protection as glass windscreens.
The paper presents a methodology for the benefit estimation of several secondary safety systems for pedestrians, using the exceptional data depth of GIDAS. A total of 667 frontal pedestrian accidents up to 40kph and more than 500 AIS2+ injuries have been considered. In addition to the severity, affected body region, exact impact point on the vehicle, and the causing part of every injury, the related Euro NCAP test zone was determined. One results of the study is a detailed impact distribution for AIS2+ injuries across the vehicle front. It can be stated, how often a test zone or vehicle part is hit by pedestrians in frontal accidents and which role the ground impact plays. Basing on that, different secondary safety measures can be evaluated by an injury shift method concerning their real world effectiveness. As an example, measures concerning the Euro NCAP pedestrian rating tests have been evaluated. It was analysed which Euro NCAP test zones are the most effective ones. In addition, real test results have been evaluated. Using the presented methodology, other secondary safety like the active bonnet (pop-up bonnet) or a pedestrian airbag measures can be evaluated.
Accident data shows that the vast majority of pedestrian accidents involve a passenger car. A refined method for estimating the potential effectiveness of a technology designed to support the car driver in mitigating or avoiding pedestrian accidents is presented. The basis of the benefit prediction method consists of accident scenario information for pedestrian-passenger car accidents from GIDAS, including vehicle and pedestrian velocities. These real world pedestrian accidents were first reconstructed and the system effectiveness was determined by comparing injury outcome with and without the functionality enabled for each accident. The predictions from Volvo Cars" general Benefit Estimation Model are refined by including the actual system algorithm and sensing models for a relevant car in the simulation environment. The feasibility of the method is proven by a case study on a authentic technology; the Auto Brake functionality in Collision Warning with Full Auto Brake and Pedestrian Detection (CWAB-PD). Assuming the system is adopted by all vehicles, the Case Study indicates a 24% reduction in pedestrian fatalities for crashes where the pedestrians were struck by the front of a passenger car.
There is a need for detecting characteristics of pedestrian movement before car-pedestrian collisions to trigger a fully reversible pedestrian protection system. For this purpose, a pedestrian sensor system has been developed. In order to evaluate the effectiveness of the sensor system, the in-depth knowledge of car-pedestrian impact scenarios is needed. This study aims at the evaluation of the sensor system. The accident data are selected from the STRADA database. The accident scenarios available in this database were evaluated and the knowledge of the most common scenarios was developed in terms of the pedestrian trajectory, the pedestrian speed, the car trajectory, the car velocity, etc. A mathematical model was then established to evaluate the sensor system with different detective angles. It was found that in order to detect all the pedestrians in the most common scenarios on time the sensor detective angle must be kept larger than 60 degrees.
Advancing active safety towards the protection of vulnerable road users: the PROSPECT project
(2017)
Accidents involving Vulnerable Road Users (VRU) are still a very significant issue for road safety. According to the World Health Organisation, pedestrian and cyclist deaths account for more than 25% of all road traffic deaths worldwide. Autonomous Emergency Braking Systems have the potential to improve safety for these VRU groups. The PROSPECT project (Proactive Safety for Pedestrians and Cyclists) aims to significantly improve the effectiveness of active VRU safety systems compared to those currently on the market by expanding the scope of scenarios addressed by the systems and improving the overall system performance. The project pursues an integrated approach: Newest available accident data combined with naturalistic observations and HMI guidelines represent key inputs for the system specifications, which form the basis for the system development. For system development, two main aspects are considered: advanced sensor processing with situation analysis, and intervention strategies including braking and steering. All these concepts are implemented in several vehicle prototypes. Special emphasis is put on balancing system performance in critical scenarios and avoiding undesired system activations. For system validation, testing in realistic scenarios will be done. Results will allow the performance assessment of the developed concepts and a cost-benefit analysis. The findings within the PROSPECT project will contribute to the generation of state -of-the-art knowledge, technical innovations, assessment methodologies and tools for advancing Advanced Driver Assistance Systems towards the protection of VRUs. The introduction of a new generation safety system in the market will enhance VRU road safety in 2020-2025, contributing to the "Vision Zero" objective of no fatalities or serious injuries in road traffic set out in the Transport White Paper. Furthermore, the test methodologies and tools developed within the project shall be considered for the New Car Assessment Programme (Euro NCAP) future roadmaps, supporting the European Commission goal of halving the road toll in the 2011-2020 timeframe.
Der Vorschlag, dass alle Kraftfahrzeuge auch am Tag mit Licht fahren sollen, wird seit vielen Jahren national und international diskutiert. Aufgrund dessen hat das Bundesministerium für Verkehr, Bau- und Wohnungswesen die Bundesanstalt für Straßenwesen beauftragt, die Auswirkungen des Fahrens mit Licht am Tag auf die Straßenverkehrssicherheit in Deutschland im Rahmen eines Forschungsprojektes genauer zu untersuchen. Auf der Basis einer Bewertung der internationalen Literatur zur Wirksamkeit des Fahrens mit Licht am Tag kommt die BASt zu dem Ergebnis, dass bei obligatorischer Einführung dieser Verkehrssicherheitsmaßnahme in der Bundesrepublik Deutschland eine deutliche Verbesserung der Verkehrssicherheit erwartet werden kann. Die Unfallrückgänge liegen in einer Größenordnung von über 3%. Die Befürchtung, dass sich demgegenüber Nachteile für schwächere Verkehrsteilnehmer, insbesondere Motorradfahrer, ergeben und deren Unfallhäufigkeit steigt, konnte nicht erhärtet werden. Die obligatorische Einführung des Fahrens mit Licht am Tag ist unter gesamtwirtschaftlichen Gesichtspunkten auch effizient. Den zu erwartenden Sicherheitsnutzen in Höhe von umgerechnet 1 Mrd. € je Jahr stehen Kosten in Folge des zunehmenden Kraftstoffverbrauchs und der damit verbundenen Emissionen in Höhe von 630 Mio. € (ungünstigster Fall: Fahren mit Abblendlicht) gegenüber. Auf lange Sicht sinken mit speziellen Tagfahrleuchten diese Kosten auf 150 Mio. € (Tagfahrleuchten in Glühlampentechnik) oder sogar nur 60 Millionen Euro (Tagfahrleuchten in LED-Technik). Es wird deshalb empfohlen, - für Neufahrzeuge eine Ausrüstung mit Tagfahrleuchten mit automatischer Aktivierung, gekoppelt an die Zündung, vorzuschreiben, - sowie einen Dämmerungsschalter zur automatischen Einschaltung des Abblendlichts obligatorisch einzuführen. Um einen nachteiligen Sicherheitseffekt durch die Durchmischung mit beleuchteten und unbeleuchteten Fahrzeugen zu vermeiden, ist für Altfahrzeuge ohne spezielle Tagfahrleuchten das Fahren mit Licht am Tag ganzjährig auf dem gesamten Straßennetz dringend zu empfehlen. Die Empfehlung für den bestehenden Kraftfahrzeugbestand sollte spätestens zum Zeitpunkt der Einführung der Ausstattungsvorschrift für die Neufahrzeuge ausgesprochen werden.
Description of road traffic related knee injuries in published investigations is very heterogeneous. The purpose of this study was to estimate the risk of knee injuries in real world car impacts in Germany focusing vulnerable road users (pedestrians, bicyclists and motorcyclists) and restrained car drivers. The accident research unit analyses technical and medical data collected shortly after the accident at scene. Two different periods (years 1985-1993 and 1995-2003) were compared focusing on knee injuries (Abbreviated Injury Scale (AISKnee) 2/3). In order to determine the influences type of collision, direction and speed as well as the injury pattern and different injury scores (AIS, MAIS, ISS) were examined. 1.794 pedestrians, 742 motorcyclists, 2.728 bicyclists and 1.116 car drivers were extracted. 2% had serious ligamentous or bony injuries in relation to all injured. The risk of injury is higher for twowheelers than for pedestrians, but knee injury severity is higher for the latter group. Overall the current knee injury risk is low and significant reduced comparing both time periods (27%, p<0,0001). Severe injuries (AISKnee 2/3) were below 1%). Improved aerodynamic design of car fronts reduced the risk for severe knee injuries significantly (p=0,0015). Highest risk of injury is for motorcycle followed by pedestrians, respectively. Knee protectors could prevent injuries by reducing local forces. The classically described dashboard injury was rarely identified. The overall injury risk for knee injuries in road traffic is lower than estimated and reduced comparing both periods. The aerodynamic shape of current cars compared to older types reduced the incidence and severity of knee injuries. Further modification and optimization of the interior and exterior design could be a proper measurement. Classic described injury mechanisms were rarely identified. It seems that the AIS is still underestimating extremity injuries and their long term results.