91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
- Buch (Monographie) (70)
- Konferenzveröffentlichung (53)
- Arbeitspapier (6)
- Bericht (5)
- Wissenschaftlicher Artikel (3)
- Teil eines Buches (Kapitel) (1)
Schlagworte
- Germany (138) (entfernen)
Topics of the status report are: Road accidents in Germany " Socio-economic costs due to road traffic accidents in Germany " Vehicle population and road performance " Electromobility " Alternative power train technologies: market penetration and consequences. The following research subjects are presented: Safety of electric vehicles " Driving dynamics of electric propelled vehicles " New requirements for the periodic technical inspection of electric and hybrid vehicles " Forward looking safety systems " Periodic roadworthiness tests " Cooperative systems: integration of existing systems " Safety related traffic information " Urban space: User oriented assistance systems and network management " Automated driving " Study on camera-monitor-systems " Freight transport " BioRID TEG, dummy harmonization " Frontal impact and compatibility " Child safety " FlexPLI " GIDAS: a blueprint for worldwide in-depth road accident investigations " Druid: Driving under the influence of drugs, alcohol and medicines " Smoke and toxicity in bus fires.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Topics of this report are: Road accidents in Germany - Socio-economic costs due to road traffic accidents - Vehicle population and road performance " Automotive IT " Electromobility. The following research subjects are presented: Safety of electric vehicles - Forward looking safety systems - Cooperative systems - Safety related traffic information - Freight transport: Action plan freight transport and trial with longer trucks - Lane departure warning systems and Advanced emergency braking systems (AEBS) for heavy duty vehicles - Dummy harmonization " Compatibility - Child safety - Virtual testing - Driving under the influence of drugs, alcohol and medicines - Fire safety of buses - Milled shoulder rumble strips - Conspicuity of powered-two-wheelers - Automatically dipped high beam and rear view mirrors.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
Aktive Systeme der passiven Fahrzeugsicherheit zum Fußgängerschutz, sogenannte crash-aktive Fußgängerschutzsysteme, werden seit 2005 zur Erfüllung der gesetzlichen Anforderungen (siehe Verordnung (EG) Nr. 78/2009 und 631/2009) in Serienfahrzeugen eingesetzt. Diese crash-aktiven Fußgängerschutzsysteme stellen im Gegensatz zu den rein passiven Systemen nur eine instationäre Lösung dar. Da die innerhalb der gesetzlichen Anforderungen definierten Testverfahren zur Bewertung stationärer Systeme entwickelt wurden, können derzeit mögliche Risiken instationärer Systeme nicht berücksichtigt werden. Im Rahmen dieses Forschungsprojektes soll ein Bewertungsverfahren für diese crash-aktiven Fußgängerschutzsysteme entwickelt werden, welches das reale Potential dieser Systeme möglichst gut wiedergibt. Basis hierfür soll eine umfangreiche Untersuchung zusätzlicher Risiken bilden. Die hier untersuchten instationären Schutzmaßnahmen werden nur im Falle eines Fahrzeuganpralls gegen Fußgänger aktiviert, der daher zuverlässig erkannt werden muss. Für die hierfür eingesetzten, kontaktbasierten Sensorsysteme stellen Fußgänger mit geringen Lasteinträgen in die Fahrzeugfront eine große Herausforderung dar. Die Lasteinträge hängen von zahlreichen Faktoren, wie bspw. der Höhe der entsprechenden Krafteinleitungspfade sowie der Größe und dem Gewichts des Fußgängers, ab. Mit Hilfe von umfangreichen Anprallversuchen und -simulationen wird gezeigt, dass die bisher eingesetzten Prüfkörper nur zum Teil für die Erfüllung dieser Anforderungen geeignet sind. Für ein geeignetes Prüfverfahren müssen daher neue Prüfkörper entwickelt werden. Durch die Aktivierung der Schutzmaßnahme soll bei den crash-aktiven Systemen vor allem das Verletzungsrisiko beim Kopfanprall verringert werden. Hierfür wird häufig die hintere Motorhaubenkante angehoben, um zusätzlichen Deformationsfreiraum zur Verfügung zu stellen. Die Haubenanhebung kann jedoch auch in zusätzlichen Verletzungsrisiken resultieren, bspw. durch die exponierte hintere Haubenkante oder die Verringerung des Deformationsfreiraums in Folge des Oberkörperanpralls. Ein Ersatzprüfverfahren zur Bewertung der Haubendeformation mit Hilfe des Hüftimpaktors wird vorgestellt. Ein hybrides Testverfahren bestehend aus Simulation und Versuch eignet sich für eine objektive Bewertung dieser Systeme, wobei die entsprechenden Versuchsparameter mit Hilfe der vorherigen Simulation bestimmt werden können.
The BASt-project group "Legal consequences of an increase in vehicle automation" has identified, defined and consequently compiled different automation degrees beyond Driver Assistance Systems. These are partial-, high- and full automation. According to German regulatory law, i.e. the German Road Traffic Code, it has been identified that the distinctive feature of different degrees of automation is the permanent attention of the driver to the task of driving as well as the constant availability of control over the vehicle. Partial automation meets these requirements. The absence of the driver- concentration to the traffic situation and to execute control is in conflict with the use of higher degrees of vehicle automation (i.e. high and full automation). Their use is therefore presently not compatible with German law, as the human driver would violate his obligations stipulated in the Road Traffic Code when fully relying on the degree of automation these systems would offer. As far as higher degrees of automation imply free-hand driving, further research in terms of behavioural psychology is required to determine whether this hinders the driver in the execution of permanent caution as required by sec. 1 para. 1 StVO (German Road Traffic Code). As far as liabilities according to the StVG (German Road Traffic Act) are concerned, the presently reversed burden of proof on the driver within sec. 18 para. 1 S. 2 StVG might no longer be considered adequate in case of higher degrees of automation that allow the driver to draw attention from the task of driving (in case making such use of a system would be permitted by the German Road Traffic Code). The liability of the vehicle "keeper", according to the German Road Traffic Act, would remain applicable to all defined degrees of automation. In case of partial automation, the use of systems according to their limits is accentuated. The range of use that remains within the intended must be defined closely and unmistakeably. Affecting user expectations properly can immensely help to maintain safe use, in case design-measures that exclude overreliance are not available according to the current state of the art (otherwise such measures would have to be applied primarily). In case of the higher degrees of automation that no longer require the driver- permanent attention (under the presupposition their use would be permitted by the German Road Traffic Code), every accident potentially bears the risk to cause product liability on the side of the manufacturer. Liability of the manufacturer might only be excluded in case of a breach of traffic rules by a third party or in case of overriding/ oversteering by the driver. In so far aspects of German procedural law and the burden of proof are of great importance. The project group has identified the need for further continuative research not only to advance legal assessment but also to improve basic technical conditions for vehicle automation as well as product reliability.
Um die zukünftige Entwicklung von Fahrzeugen mit alternativem Antrieb in Deutschland verfolgen, analysieren und mögliche negative Auswirkungen auf die Verkehrssicherheit zeitnah identifizieren zu können, hat die Bundesanstalt für Straßenwesen (BASt) im Jahr 2010 die Einrichtung einer langfristigen Beobachtung des Fahrzeugmarktes und des Unfallgeschehens von Pkw mit alternativen Antriebsarten initiiert. Die Daten des vorliegenden Berichtes dokumentieren die Marktdurchdringung von Personenkraftwagen mit alternativen Antriebsarten und informieren über die Unfallbeteiligung von Fahrzeugen mit alternativem Antrieb bis 2011. Es hat sich gezeigt, dass Fahrzeuge mit Hybridantrieb nach wie vor ein starkes Marktwachstum aufweisen. Die Zuwachsrate ist nahezu auf dem gleichen hohen Niveau wie in den Vorjahren (ca. 28%, getypter Bestand). Bei den reinen Elektrofahrzeugen ist die Anzahl getypter Fahrzeuge sehr stark angestiegen, von 212 im Jahr 2010 auf 1880 im Jahr 2011. Der reale Bestand an Elektrofahrzeugen (inklusive ungetypter Fahrzeuge) hat sich demgegenüber von 2010 auf 2011 auf 4.541 Pkw verdoppelt. Dies deutet auf eine zunehmende Serienreife von Elektro-Kfz hin. Pkw mit alternativem Antrieb weisen 2011 (bis auf Gas) einen höheren Anteil an Unfällen innerorts auf als Pkw mit herkömmlichem Antrieb. Hybrid Fahrzeuge haben dabei eine erhöhte Beteiligungsquote innerorts von ca. 76%. Der relativ hohe Anteil von Innerortsunfällen von alternativ betriebenen Fahrzeugen ist vor allem vor dem Hintergrund der Nutzung der Fahrzeuge zu interpretieren.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.