Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (637) (entfernen)
Schlagworte
- Conference (386)
- Konferenz (382)
- Germany (212)
- Deutschland (209)
- Unfall (188)
- Accident (187)
- Safety (123)
- Sicherheit (122)
- Injury (117)
- Verletzung (117)
Institut
To assess occupant safety in a crash test, criteria associating the measurements made with a crash test dummy to injury risk are necessary. To enable better protection of elderly car occupants the objective of this study was to develop improved thoracic injury criteria for the THOR average male dummy. The development of these criteria is usually based on matched dummy and Post Mortem Human Surrogate (PMHS) tests by relating the obtained PMHS injuries to dummy measurements. This approach is limited, since only a few tests in relevant loading conditions are available and any new test series requires high efforts to be performed due to their complexity and costs. To overcome these limitations and to extend the dataset for the development of THOR dummy chest injury risk functions a simulation-based approach was applied within the EC funded project SENIORS (Safety Enhanced Innovations For older Road Users - www.seniors-project.eu). Within this study frontal impact sled simulations with an FE model representing a THOR average male dummy and matched simulations with a human body model (HBM) representing an elderly car occupant were carried out. The HBM used for this study was the THUMS TUC with modified rib cage, which was developed in SENIORS. The modifications included material and geometry changes aiming to represent an elderly car occupant. The rib fracture risk was predicted with a deterministic approach whereby a rib was considered broken when the strain exceeded an age-dependent threshold. Furthermore, a probabilistic method was applied to predict the probability of sustaining a certain number of fractured ribs by comparing local strain values to the distribution of cortical rib ultimate strain. By relating the output from the HBM simulations to a multi-point dummy injury criterion, injury risk curves were calculated by statistical methods. The wide range of loading conditions resulted in the desired range of injuries and THOR ATD output. The number of fractured ribs predicted by the HBM based on the deterministic prediction method was between 0 and 15. Furthermore, the probabilistic risk for the number of rib fractures equal or greater than two, three or four was calculated for each load case. The THOR rib deflection criterion Rmax was between 18 and 56 mm, while the PC Score was in the range of 2.5 to 7.2. Based on these outputs new risk curves for the predicted deterministic (AIS2+/3+) and probabilistic injury risk were calculated. The new curves show reasonable shapes and significance that provide trust in their application. The new risk curves are compared to risk curves obtained by traditional methods. The results were found similar to previous injury risk functions based on physical tests, which gives a high level of confidence in the chosen approach. The simulation-based approach of matched ATD model vs. HBM simulation was successfully applied. Rmax curves show a slightly better quality than the injury criterion PC Score.
Ein auf Nachhaltigkeit angelegtes Großprojekt wie das der Zustandserfassung und -bewertung (ZEB) bedarf eines Qualitätssicherungssystems. Hierfür wurde auf Initiative des Bundesministeriums für Verkehr, Bau- und Wohnungswesen (BMVBW) eine Untersuchung ausgelöst, über die die Grundlagen und Voraussetzungen für ein umfassendes QS-System erarbeitet werden sollen. In einer Pilotierungsphase soll im Jahr 2002 die Machbarkeit nachgewiesen werden.
Neue Herausforderungen an die Unfallforschung durch Fahrerassistenz und automatisiertes Fahren
(2019)
Unfallrekonstruktion hat die Ableitung von Maßnahmen zur Minimierung der Unfallfolgen ermöglicht, vor allem durch Verbesserungen bei passiven Sicherheitseinrichtungen, aber auch durch die Verbesserung der Rettungskette, beispielsweise eCall. Heute können aktive Sicherheitssysteme die Unfallfolgen bereits vor der eigentlichen Kollision reduzieren oder durch Umfeldwahrnehmung und mittels Eingriff in die Fahrzeugsteuerung gegebenenfalls sogar vollständig verhindern. Funktionen, die aktiv in die Fahrzeugsteuerung eingreifen, lassen sich nach ihrer Wirkweise unterscheiden: zum einen handelt es sich um kontinuierlich automatisierende Funktionen, die meist länger aktiv bleiben (zum Beispiel ACC). Zum anderen um Funktionen, die in kritischen Fahrsituationen temporär in die Fahrzeugsteuerung eingreifen. Aufgezeigt wird, welche Konsequenzen und Risiken in Bezug auf diese Systeme sowie für bestimmte (zum Beispiel kritikale) Fahrsituationen anzunehmen sind. Zur Bewertung von aktiven Reglern, die in kritischen Fahrsituationen eingreifen, sind Unfalldaten nur noch eingeschränkt tauglich. Ähnliches gilt für die Bewertung von Ereignissen/ Zuständen im Rahmen kontinuierlicher Fahrzeugsteuerung, vor allem, wenn diese weiter vorausliegen. Wirkzusammenhänge automatisierter Fahrfunktionen müssen jedoch - gerade für den Mischverkehr mit konventionell gesteuerten Fahrzeugen - identifiziert werden. Dafür wird eine Szenariendatenbank mit relevanten Verkehrssituationen benötigt, in die Daten aus Naturalistic Driving Studies (NDS), aus Fahrversuchen oder Versuchen im Fahrsimulator eingehen können. Die zunehmende Durchdringung der Fahrzeugflotte mit kontinuierlich automatisierten Fahrfunktionen lässt eine Abnahme kritischer Fahrsituationen und eine Reduktion der Zahl der Verkehrsopfer erwarten. Allerdings verbleibt eine Restzahl an systemimmanenten Unfällen, die als unvermeidbar gelten müssen.
The Netherlands is on the way to change its existing skid resistance measuring method for its highway network from the Dutch RAW 72, a longitudinal force method, to the Sideway Force method. This method is described in the Technical Specification 15901-8 (SKM device) as well as 15901-6 (SCRIM device) and is in use in 9 European countries. The CEN TC 227 WG5 on Surface Characteristics is currently working on combining of these two technical Specifications into a European standard for Sideway-Force (SWF) measurement devices. The idea of this change in the Netherlands was perceived in 2013 and since then a lot of meetings have been held with the different Dutch decision makers as well as with countries which currently operate SWF devices. There was an intensive exchange of knowledge about these devices and their corresponding quality assurance systems, because the Netherlands wanted to incorporate and rely on an existing system of a neighbor country without losing their present level of quality. The Netherlands has therefore decided to incorporate the German SKM approach. The network monitoring with the new system will start in 2017. To ensure the quality of skid resistance measurements and further cooperation in this field, it has been decided to initiate an alliance between BASt and the Dutch road owner Rijkswaterstaat (RWS). This alliance will facilitate an exchange of research activities, calibration of the Dutch systems according to the existing German Standard as well as control measurements with a BASt-device on the Dutch network during the network monitoring. During 2016 also comparative measurements will be performed on a network level with the current Dutch device and with an SKM device to determine a conversion between the two and to be able to define new threshold values.
Rekonstruktion des Bestandsplans im Zuge der Nachrechnung der Brücke über die Leine bei Schwarmstedt
(2019)
Der aktuell im Rahmen der Nachrechnungsrichtlinie geforderte Nachweis von Tragfähigkeit, Gebrauchstauglichkeit und Ermüdung der Brückenbauwerke im Bestand der Länder und des Bundes stellt eine enorme Herausforderung dar. Insbesondere bei unvollständigen oder fehlenden Bestandsplänen der Bauwerke sind Maßnahmen erforderlich, um die erforderlichen Informationen zu beschaffen. Ein wirkgungsvolles Instrument könne hierfür die zerstörungsfreien Prüfverfahren des Bauwesens sein. In dem präsentierten Forschungsprojekt erfolgte die Rekonstruktion eines Bestandsplanes direkt auf die Anforderungen des mit der Nachrechnung beauftragten Ingenieurbüros. Darüber hinaus wurde der Entwurf eines Leitfadens erstellt, der im Falle von unvollständigen oder fehlenden Bestandsplänen die Grundlagen für die Beauftragung und Durchführung der Nachrechnung schafft.
Innovative Zugangstechniken und digitale Bildauswertung für die Bauwerksprüfung im Zuge von Straßen
(2019)
Deutschland braucht ein zuverlässiges Straßenverkehrssystem. Dafür müssen die Zustände der Brücken und sonstigen Ingenieurbauwerke der Straßen kontinuierlich und umfassend bekannt um rechtzeitig handeln zu können. Neben der regulären visuellen Bauwerksprüfung nach DIN 1076 bieten neue innovative Verfahren große Möglichkeiten der Zugangs- sowie Bilderfassungs- und Bildverarbeitungstechnik. Diese Möglichkeiten gilt es jetzt systematisch zu erkunden und für den Einsatz aufzubereiten
As investigations by BASt have shown, a bond between concrete surfaces and bases may be a disadvantage when water penetrates via joints and from the sides if the bond becomes partially detached at an early stage. Free water may penetrate into the area between the concrete surface and the base and build up in areas where the bond is still intact. The high pressure caused by lorry wheels rolling over the pavement causes hydrodynamic pumping. This creates very high flow speeds with considerable corrosion power. This results in the base course surface being eroded in the areas where heavy vehicles drive over the road and may even lead to water and fine particles from the base courses being expelled through the longitudinal joints between the pavement slab and the lower hard shoulder or first overtaking lane. The erosion of the base leads unavoidably to the bearing conditions deteriorating and increased loading of the concrete surface. Cracks may occur and, later stepping-off and tilting of the plates components. This significantly deteriorates the evenness and consequently the service value of the road. This finally leads to a reduction in the service life of the concrete surface. To avoid such damage water which has penetrated must be able to lose pressure and to then seep away. A possible solution is: A nonwoven fabric substance between concrete suface and bound base course. This construction method has proved himselve on numerous test road sections and were rightly included in the new Codes of Practice for the Standardisation of the Upper Structure of Traffic-Bearing Surfaces (Richtlinien für die Standardisierung des Oberbaues von Verkehrsflächen- RStO).
Federal highway A 26 in Germany : reinforced dams in soft soils - control method according DIN 1054
(2004)
In 2001 the construction of the Federal Highway A 26 in Lower Saxony (north of Germany) was started. In this area the underground is without any substantial bearing capacity as it consists of soft layers ( clay, peat) with a thickness of up to 12 m. Because it was not possible to exchange the soil neither completely nor partially pre-loading procedure (consolidation method) was chosen for this construction. Short- and long-term stability are ensured by the use of high-tensile fabrics for reinforcement at the dam basis. The vertical and horizontal deformations and the stress changes in the soil, caused by the pre-load procedure, has to be controlled by special geotechnical measurements. Additionally, in the higher parts of the dam the strain behaviour of the high-tensile fabrics is measured. These measurements form the basis for the application of the control method according DIN 1054. In this article, the special circumstances of this project are described. Further on the geotechnical measurements, the winning and evaluation of the necessary parameters of the subsoil, and the consequences of these data for the ongoing of the project are laid down. Intermediate results of the geotechnical measurements are described.
Seit mehreren größeren Brandereignissen in Straßentunneln um die Jahrtausendwende wurde sowohl im baulichen Brandschutz als auch in der sicherheitstechnischen Tunnelausstattung viel getan. Zahlreiche technische Neu- und Weiterentwicklungen haben seither Eingang in Bau, Ausstattung und Betrieb der Bauwerke gefunden. Im europäischen aber auch weltweiten Vergleich befinden sich die deutschen Straßentunnel auf einem sehr hohen Sicherheitsniveau. Dies ist auch erforderlich, da Deutschland als Transitland in Europa über ein hoch belastetes Straßennetz verfügt. Tunnel stellen neuralgische Punkte in diesem Netz dar. Daher gilt es hier für den Nutzer ein Optimum an Sicherheit zu gewährleisten, gleichzeitig aber auch den Verkehrsfluss so gering wie möglich durch Wartungs- bzw. Sperrzeiten der Tunnelröhren zu behindern. Mit diesem Tagungsband sollen die neuesten Erkenntnisse sowohl zur Verkehrssicherheit in Tunneln, als auch zur bautechnischen Sicherheit für die Verwendung in der alltäglichen Praxis nähergebracht werden. Nach einem allgemeinen Überblick zum Stand von aktuellen Bau-, Instandsetzungs- und Nachrüstungsmaßnahmen im deutschen Fernstraßentunnelnetz erfolgt die Vorstellung zweier Forschungsprojekte der BASt, dem europäischen Projekt ECOROADS, welches die Harmonisierung zwischen Sicherheitsanforderungen auf freier Strecke und Tunnel zum Inhalt hat, und dem BASt-eigenen Modelltunnel, in dem längsneigungsabhängige, modellmaßstäbliche Rauchausbreitungsuntersuchungen vorgenommen wurden. Im zweiten Themenbereich, der die Grundlagen für Planung und Bau fokussiert, wird auf die Fortschreibung des betriebstechnischen Regelwerks, die Entwicklung von Kostenansätzen für Straßentunnel sowie auf planerische Herausforderungen im Rahmen des Großprojektes Fehmarnbeltquerung eingegangen. Im Themenschwerpunkt Tunnelbetrieb werden neue Erkenntnisse zur Belüftung von Straßentunneln bei Stau und den damit verbundenen Auswirkungen auf die Risikoanalyse vorgestellt. Außerdem gibt es ein Update zum Stand der Umsetzung des Pilotprojektes Tunnelsimulator aus zwei Bundesländern. Im Rahmen der Beiträge zu Instandsetzung und Nachrüstung von Straßentunneln wird dem aktuellen Thema des Umgangs mit Chloridbelastungen von Tunnelinnenschalen nachgegangen, sowie den Besonderheiten bei der Nachrüstung mehrerer Bestandstunnelbauwerke der Stadt Köln mit Schwerpunkt auf dem Stadtautobahntunnel Kalk. An dieser Stelle sei allen Autoren gedankt, die zu dieser gelungenen Veranstaltung beigetragen haben.
Automated driving will provide many kinds of benefits - some direct and some indirect. The benefits originate at the individual level, from changes in the behaviour of drivers and travellers with regard to driving and mobility, ending up with benefits at the social level via changes in the whole transport system and society, where many of the current planning and operations paradigms are likely to be transformed by automated driving. There may also be disbenefits, particularly at a social level, for example in intensity of travel which could result in additional congestion and increased use of natural resources. There may also be unintended consequences. For example, we do not know the impacts on public transport: driverless vehicles could provide a means to a lower cost service provision, but the availability of automated cars could lead to more car travel at the expense of collective transport.
In line with the new definition introduced by the European Commission (EC), the number of seriously injured road casualties in Germany for 2014 is assessed in this study. The number of MAIS3+ casualties is estimated by two different methodological approaches. The first approach is based on data from the German Inâ€Depth Accident Study (GIDAS), which is closely related to the German Road Traffic Accident Statistics. The second approach is based on data from the German TraumaRegister DGU-® (TRâ€DGU), which includes many more hospitals but not all MAIS3+ injuries.
Im Erd- und Straßenbau ist es in den letzten Jahren bei bindemittelbehandelten sulfathaltigen Böden wiederholt zu teilweise erheblichen Schäden durch Quellhebungen gekommen, die auf eine Mineralreaktion im Boden zurückzuführen sind. Werden Böden mit natürlichem Sulfatgehalt zu bautechnischen Zwecken mit calciumbasierten Bindemitteln behandelt, so kann das Bindemittel unter bestimmten Randbedingungen mit den im Gips enthaltenen Sulfationen zum Mineral Ettringit reagieren. Infolge der mit dieser Mineralneubildung verbundenen Volumenvergrößerung kann es zu erheblichen Hebungsschäden kommen. Die für die Reaktion des Sulfattreibens im Boden maßgebenden Einflussfaktoren sind zwar grundsätzlich bekannt, quantitative Prüfmethoden und standardisierte Strategien zur Gefahrenabwehr lagen bis dato allerdings noch nicht vor. Das Ziel des Forschungsvorhabens, über das in diesem Beitrag berichtet wird, war die Entwicklung eines praxistauglichen Prüfverfahrens als Grundlage für eine hieraus abzuleitende Prüfvorschrift. Hierfür wurden an Proben aus verschiedenen Boden-Bindemittelgemischen mit definierten Sulfatgehalten Quellhebungsversuche geplant, durchgeführt und ausgewertet. Im Ergebnis wurde ein annähernd linearer Zusammenhangzwischen dem Sulfatgehalt im Boden und den eingetretenen Quellhebungen festgestellt. Die Ergebnisse zeigen ferner, dass eine Behandlung sulfathaltiger Böden mit Weißfeinkalk mit größeren Quellhebungen verbunden ist als eine Behandlung mit Zement.
Die Europäischen Normen für Erdarbeiten werden im CEN/TC 396 "Earthworks" erarbeitet. Das Sekretariat des CEN/TC 396 wird vom französischen Normungsinstitut AFNOR gehalten. Die Normungsarbeit wird im DIN-Ausschuss NA 005-05-22 AA "Erdarbeiten (SpA zu CEN/TC 396), Gemeinschaftsausschuss mit FGSV GA 5.01" gespiegelt. Vertreter des Spiegelausschussesarbeiten in den verschiedenen Arbeitsgruppen (working groups (WG)) des CEN/TC 396 mit. In den Jahren 2009 und 2010 wurden die Gremien konstituiert und mit der Normungsarbeit begonnen, zunächst überwiegend durch die Zusammenstellung der vorhandenen Regelungen in den Mitgliedsstaaten (siehe auch Beitrag Vogel/Leister/Heyer zur Erd- und Grundbautagung 2013). Im November 2014 wurden vom CEN/TC 396 die Arbeitsaufträge("work items") offiziell gestartet.
Die Länderarbeitsgemeinschaften Bodenschutz (LABO), Abfall (LAGA) und Wasser (LAWA) haben im September 2005 das Bundesumweltministerium gebeten, bundeseinheitliche, rechtsverbindliche Anforderungen an die Verwertung von mineralischen Abfällen in technischen Bauwerken und in bodenähnlichen Anwendungen zu regeln. Die Umweltministerien der Länder haben in ihren Stellungnahmen zum 2. Arbeitsentwurf der Mantelverordnung Forderungen gestellt, bei deren Umsetzung der Einsatz von mineralischen Ersatzbaustoffen im Verkehrswegebau stark eingeschränkt und unwirtschaftlich würde. Der Wille zur Schonung natürlicher Ressourcen ist nicht erkennbar. Anforderungen an Straßenbauwerke, an den Umweltschutz und an die Kreislaufwirtschaft konkurrieren in vielen Bereichen miteinander. Im Gesetzgebungsverfahren sind bisher trotz Gesprächen zwischen den Ressorts auf Arbeitsebene in grundlegenden Aspekten keine Einigung oder von Allen tragbare Kompromisse erzielt worden. Der Verkehrswegebau ist Hauptabnehmer der Ersatzbaustoffe, geht mit großen Mengen des Primärbaustoffs "Boden" um, ist aber auch "Abfallerzeuger". In der Mantelverordnung werden Regelungen getroffen, die stark in die Belange des Straßenbaus eingreifen. Aus diesem Grund ist die Beteiligung der Straßenbauverwaltung erforderlich, um die bautechnische und bauvertragliche Kompetenz sicher zu stellen, das Potenzial für Boden- und Grundwasserschutz auszuschöpfen und natürliche Ressourcen zu schonen. Die wichtigsten Aspekte zum umweltgerechten Einsatz von Boden und Ersatzbaustoffen aus der Sicht des Straßenbaus werden vorgestellt.
Cycling and designing for cyclist in Germany: an overview of road safety, research and guidelines
(2016)
Cycling is considered a social, eco-friendly, pollution-free, low noise and healthy activity and mode of transportation. There are currently around 67 million bicycles in Germany. This number is expected to increase in the near future with greater use of electromotive assisted bicycles. Regarding the expected increase, there should be additional attention given to road traffic accidents involving cyclists. In 2014, 396 cyclists were killed in road accidents in Germany, which is 12 % of all road fatalities. Also in 2014, Germany reported over 78,000 injuries to cyclists. The majority of the fatalities (about 58 %) and 83 % of the serious injuries to cyclists occurred in urban areas. This paper will examine three aspects concerning cyclists. First, the paper will show the main current developments, for example the National Cycling Plan 2020, the effects of the road safety programme and provide an analysis of the German national accident statistics. Second, the paper will give an overview of the regulations, guidelines for road traffic and designing of cycling facilities. Lastly, this study will detail the current and completed research in Germany addressing cyclist. For example, the paper will discuss the topic "Accidents between Turning-off Trucks and Cyclists" Accidents between right turning trucks and straight riding cyclists often show massive consequences. Accident severity is much higher than in other accidents. The situation is critical especially due to the fact that, in spite of the six mirrors that are mandatory for ensuring a minimum field of sight for the truck drivers, cyclists in some situations cannot be seen or are not seen by the driver. Either the cyclist is overlooked or is in a blind spot area that results from the turning manoeuvre of the truck. At present driver assistance systems are discussed that can support the driver in the turning situation by giving a warning when cyclists are riding parallel to the truck just before or in the turning manoeuvre. The paper will describe the requirements for turning assist systems for trucks. The outcome of the study is an overview of the accident situation between right turning trucks and straight driving cyclists in Germany as well as a corresponding test procedure for driver assistance systems. Below are several other projects which will be investigated, too: Accident Risk and Acceptance of Traffic-Rules by Cyclists ; Safety Improvement in Terms of Using Bicycle Paths in the Opposite Direction ; Cycling in Mixed-Traffic ; Observation of Pedal Electric Cycles Riders to Identify Safety Concerns. These three aspects will provide the current situation on the topic of cyclist safety in Germany.
Bewertung der strukturellen Substanz für die systematische Erhaltungsplanung von Betonfahrbahndecken
(2016)
"Mobilität ist zentrale Voraussetzung für wirtschaftliches Wachstum, Beschäftigung und Teilhabe des Einzelnen am gesellschaftlichen Leben." Dieser Leitsatz des BMVI setzt eine intakte und funktionierende Infrastruktur voraus. Im Kontext mit dem Investitionshochlauf in den nächsten Jahren ist für das Bundesfernstraßennetz insbesondere ein netzbezogenes systematisches Vorgehen im Rahmen der Baulichen Erhaltung von Relevanz. Bei der Planung von Erneuerungsmaßnahmen ist dabei die Kenntnis über den Zustand der strukturellen Substanz und deren langfristige Entwicklung von zentraler Bedeutung. Nachfolgend wird ein Verfahren vorgestellt, das die mechanisch und statistisch abgesicherte Bewertung und Prognose der strukturellen Substanz von Betonfahrbahndecken ermöglicht. Zudem werden die Anwendung und das Vorgehen anhand eines Praxisbeispiels aufgezeigt.
Die Ermittlung einer voraussichtlichen Restnutzungsdauer von Verkehrsbefestigungen und somit der Abschätzung des Eingreifzeitpunktes für eine grundhafte Erneuerung ist ohne die Kenntnis der strukturellen Substanz nur sehr unzureichend zu bewerkstelligen. Mit Vorliegen des Entwurfes zu den "Richtlinien zur Bewertung der strukturellen Substanz des Oberbaus von Verkehrsflächen in Asphaltbauweise" (RSO Asphalt) ist zwar ein hierfür nutzbares Verfahren verfügbar, allerdings basiert dieses auf der Analyse von Laborversuchen an den aus Streckenabschnitten zu entnehmenden Bohrkernen, wodurch eine netzweite Anwendung nicht praktikabel ist. Um trotzdem einen umfassenden Einsatz zu ermöglichen und eine deutliche Verbesserung gegenüber bisherigen Verfahren herbeizuführen, können aber begründete Annahmen zu den Materialkennwerten getroffen werden. Alle weiteren Eingangsdaten des Verfahrens decken sich mit denen des bisherigen. Deren Vollständigkeit und Plausibilität muss zukünftig mehr Bedeutung zugemessen werden.
Fire incidents are among the most relevant for people in a tunnel. Therefore, it is important to be sufficiently prepared for such events. A large scale fire test is to be used to help evaluate the initial burning duration and the time it takes for the fire to spread to other vehicles in the tunnel, and in particular how long it takes for a truck carrying wooden pallets to catch fire, taking into consideration the extremely high temperatures. The goal, therefore, is to determine the time it takes for a fire to spread to other vehicles in the tunnel. In the large scale fire test, an accident in a tunnel with one-way traffic is simulated between a truck loaded with approximately 3.7 t of wooden Europol pallets and a passenger car. Directly behind each of the vehicles involved in the accident there is another car which stops at a distance of 1.0 m. Approximately 300 litres of burning diesel are discharged from the truck's fuel tank, which is simulated by using approximately 400 litres of isopropanol. A 10 m-² burning pool forms underneath the truck. Other objectives of the large scale fire test are the validation of the CFD models and the evaluation of the progression of the thermal release ratios estimated for the simulation. The thermal release ratios generated in the test are determined and evaluated using various models.
Die Europäischen Normen für Erdarbeiten werden im CEN/TC 396 "Earthworks" erarbeitet. Das Sekretariat des CEN/TC 396 wird vom französischen Normungsinstitut AFNOR gehalten. Die Normungsarbeit wird im DIN-Ausschuss NA 005-05-22 AA "Erdarbeiten (SpA zu CEN/TC 396), Gemeinschaftsausschuss mit FGSV GA 5.01" gespiegelt. Vertreter des Spiegelausschusses arbeiten in den verschiedenen Arbeitsgruppen (Working Groups (WG)) des CEN/TC 396 mit. In den Jahren 2009 und 2010 wurden die Gremien konstituiert und mit der Normungsarbeit begonnen, zunächst überwiegend durch die Zusammenstellung der vorhandenen Regelungen in den Mitgliedsstaaten (siehe auch Beitrag Vogel/Leister/Heyer zur Erd- und Grundbautagung 2013). Im November 2014 wurden vom CEN/TC 396 die Arbeitsaufträge ("work items") offiziell gestartet.
Die Länderarbeitsgemeinschaften Bodenschutz (LABO), Abfall (LAGA) und Wasser (LAWA) haben im September 2005 das Bundesumweltministerium gebeten, bundeseinheitliche, rechtsverbindliche Anforderungen an die Verwertung von mineralischen Abfällen in technischen Bauwerken und in bodenähnlichen Anwendungen zu regeln. Die Umweltministerien der Länder haben in ihren Stellungnahmen zum 2. Arbeitsentwurf der Mantelverordnung Forderungen gestellt, bei deren Umsetzung der Einsatz von mineralischen Ersatzbaustoffen im Verkehrswegebau stark eingeschränkt und unwirtschaftlich würde. Der Wille zur Schonung natürlicher Ressourcen ist nicht erkennbar. Anforderungen an Straßenbauwerke, an den Umweltschutz und an die Kreislaufwirtschaft konkurrieren in vielen Bereichen miteinander. Im Gesetzgebungsverfahren sind bisher trotz Gesprächen zwischen den Ressorts auf Arbeitsebene in grundlegenden Aspekten keine Einigung oder von Allen tragbare Kompromisse erzielt worden. Der Verkehrswegebau ist Hauptabnehmer der Ersatzbaustoffe, geht mit großen Mengen des Primärbaustoffs "Boden" um, ist aber auch "Abfallerzeuger". In der Mantelverordnung werden Regelungen getroffen, die stark in die Belange des Straßenbaus eingreifen. Aus diesem Grund ist die Beteiligung der Straßenbauverwaltung erforderlich, um die bautechnische und bauvertragliche Kompetenz sicher zu stellen, das Potenzial für Boden- und Grundwasserschutz auszuschöpfen und natürliche Ressourcen zu schonen. Die wichtigsten Aspekte zum umweltgerechten Einsatz von Boden und Ersatzbaustoffen aus der Sicht des Straßenbaus werden vorgestellt.
Risk-based approach for the protection of land transport infrastructure against extreme rainfall
(2016)
The aim of the research project "Risk based approach for the protection of transport infrastructure against extreme rainfall RAINEX" is the development of a practical methodology for the identification and assessment of both vulnerable as well as critical transport infrastructures towards extreme rainfall events consequences. The developed methodology is based on expert knowledge and includes qualitative and semi-quantitative analyses regarding the assessment of the vulnerability and criticality of relevant transport infrastructures. The process chain from the spatial rainfall to the concentrated runoff in the river channel was shown to assess the local hazard resulting in the local risk. The main result of the project is a practice-oriented and applicable methodology and a comprehensive and well-developed security handbook.
The performance of asphalt by low temperatures is largely determined by the viscosity of the binder respectively the mortar of the asphalt. The traditional test methods for binder (e.g. ball-draw viscosimeter) are limited to temperatures above the service range of temperature for an asphalt construction. The Dynamic Shear Rheometer (DSR) is limited to temperatures above 30-°C whereas the Bending Beam Rheometer (BBR) is limited to temperatures below -10-°C and not applicable to mortar. Especially the gap in the temperature of these test methods is very important to characterize the viscosity behavior of binder and mortar over the whole range of the service temperatures, which represent the typical environmental conditions of over the seasons, for an asphalt construction. Tension retardation experiments seem to be very useful to bridge the gap. They address the low temperature behavior of binder and mortar. With this test method the flow characteristics of binder (pen grade and any modification) and any kind of mortar in the service temperature range, in particular at low temperatures of -25-°C can be determined with a high precision, and assessed, via the physically interpretable material characteristics quantity of tension viscosity. Furthermore the present findings indicate the potential of extrapolation the results of the Tension retardation for a prediction of the rutting resistance of asphalt mixtures. As part of several research Projects, BASt (Federal Highway Research Institute) investigated the effects of different modifications of the binder to low temperature behavior of the binder by the tension retardation test. This paper is intended to provide a more detailed description of the test method Tension Retardation, selected results and related findings.
Research to inform policy is often challenged with how to genuinely use and implement research findings in decision-making and policy-planning. To begin with, the dialogue between researchers and decision-makers is essential to ensure profound understanding and legitimate interpretations of the results. Furthermore, the step to drawing practical conclusions and processing them into actions can only succeed if research findings are diffused to decision-making levels with influence on the matter, and mechanisms to knowledge transfer in the presence of a stable, favourable policy environment exist. Research investments into the topic of electromobility in Europe are substantial, and subtopics aiming to inform national policy-makers address a complex set of aspects from environmental and societal to technological and economic. This paper has a two-fold objective, the first of which is to present the results of scenarios to explore electromobility deployment in Finland, Germany and the European Union. The second is to discuss the challenges and solutions to bridge the gap from research findings towards decision-making and policy-planning, using the authors' electromobility scenario work as an example. The electromobility scenarios were built using the VECTOR21 model (Mock, 2010), and the rationale was to simulate vehicle sales and markets under different policy settings and calculate the most economical solution to fulfill regulation on COâ‚‚ emissions as set by the European Commission (2009). The model allows calculating the market diffusion of alternative powertrain technologies to the European market until 2030, taking into account different taxation schemes, incentives and other country-specific characteristics. The authors also present the cost-benefit-analysis of the modelling results to assess the different scenarios and to show variation between regions regarding profitability of alternative technological or political support and interventions. To proceed from research findings towards decision-making and policy-planning, the authors made observations relating to transfer of research knowledge and interpretation of their electromobility scenario results in national policy contexts. An evaluation of how the function of research to inform policy in this case succeeded is provided. In addition, the influence of expert opinions on the political decision-making process will be discussed through experiences from an expert questionnaire conducted to survey the importance of costs, time requirement, acceptance and other criteria of promotion measures of electromobility.
With the introduction of the German Highway Capacity Manual (HBS) in January 2002 (FGSV, 2002), all methods for the evaluation of the performance of highway facilities were, for the first time in Germany, simultaneously updated and consolidated in a single work following the ideas of the American Highway Capacity Manual (HCM). This paper gives an overview of the new 2015 edition of the German HBS and describes the changes as for example the addition of chapters for freeway, rural roads, and major urban street facilities, comprising segments and intersections.
Die Kommunikation zwischen Fahrzeugen und Infrastrukturkomponenten steht vor der Einführung in Europa. Dieser Beitrag stellt zunächst die grundlegende Technologie zum Austausch von Nachrichten und ein Pilotprojekt vor, innerhalb dessen eine sichere Fahrzeug-zu-Infrastruktur Kommunikation konzipiert und praktisch erprobt wird. Darauf aufbauend werden Sicherheitsfragestellungen von Infrastrukturkomponenten beleuchtet und ein Einblick in das Schlüsselmanagement sowohl für Fahrzeuge als auch Infrastrukturkomponenten gegeben.
The current maintenance management for bridges is mainly based on visual inspection and aims at the repair of identified damages. In the project cluster "Smart Bridge" an adaptive system for holistic evaluation in real time is developed. The following pilot studies show significant aspects of the Smart Bridge. Within the research project "Digital Test Area Autobahn" a new constructed prestressed concrete bridge is implemented with instrumented expansion joints and bearings, a "RTMS©" and a sensor network. By using analytical bridge models and evaluation methods the condition and reliability of the bridge as well as the remaining service life is determined. In the pilot study "duraBASt" sensors for the detection of durability and structural safety as well as data analyzing and evaluation procedures are investigated. The aim of this study is the partial implementation of the aspects: data collection, data processing and model development for condition assessment of the bridge.
Road condition acquisition and assessment are the key to guarantee their permanent availability. In order to maintain a country's whole road network, millions of high-resolution images have to be analyzed annually. Currently, this requires cost and time excessive manual labor. We aim to automate this process to a high degree by applying deep neural networks. Such networks need a lot of data to be trained successfully, which are not publicly available at the moment. In this paper, we present the GAPs dataset, which is the first freely available pavement distress dataset of a size, large enough to train high-performing deep neural networks. It provides high quality images, recorded by a standardized process fulfilling German federal regulations, and detailed distress annotations. For the first time, this enables a fair comparison of research in this field. Furthermore, we present a first evaluation of the state of the art in pavement distress detection and an analysis of the effectiveness of state of the art regularization techniques on this dataset.
Except for corrective steering functions automatic steering is up to now only allowed at speeds up to 10 km/h according to UN Regulation No. 79. Progress in automotive engineering with regard to driver assistance systems and automation of driving tasks is that far that it would be technically feasible to realise automatically commanded steering functions also at higher vehicle speeds. Besides improvements in terms of comfort these automated systems are expected to contribute to road traffic safety as well. However, this safety potential will only be exhausted if automated steering systems are properly designed. Especially possible new risks due to automated steering have to be addressed and reduced to a minimum. For these reasons work is currently ongoing on UNECE level with the aim to amend the regulation dealing with provisions concerning the approval of steering equipment. It is the aim to revise requirements for automatically commanded steering functions (ACSF) so that they can be approved also for higher speeds if certain performance requirements are fulfilled. The paper at hand describes the derivation of reasonable system specifications from an analysis of relevant driving situations with an automated steering system. Needs are explained with regard to covering normal driving, sudden unexpected critical events, transition to manual driving, driver availability and manoeuvres to reach a state of minimal risk. These issues form the basis for the development of test procedures for automated steering to be implemented in international regulations. This holds for system functionalities like automatic lane keeping or automatic lane change as well as for addressing transition situations in which the system has to hand over steering to the driver or addressing emergency situations in which the system has to react instead of the driver.
One main objective of the EU-Project SENIORS is to provide improved methods to assess thoracic injury risk to elderly occupants. In contribution to this task paired simulations with a THOR dummy model and human body model will be used to develop improved thoracic injury risk functions. The simulation results can provide data for injury criteria development in chest loading conditions that are underrepresented in PMHS test data sets that currently proposed risk functions are based on. To support this approach a new simplified generic but representative sled test fixture and CAE model for testing and simulation were developed. The parameter definition and evaluation of this sled test fixture and model is presented in this paper. The justification and definition of requirements for this test set-up was based on experience from earlier studies. Simple test fixtures like the gold standard sled fixture are easy to build and also to model in CAE, but provide too severe belt-only loading. On the other hand a vehicle buck including production components like airbag and seat is more representative, but difficult to model and to be replicated at a different laboratory. Furthermore some components might not be available for physical tests at later stage. The basis of the SENIORS generic sled test set-up is the gold standard fixture with a cable seat back and foot rest. No knee restraint was used. The seat pan design was modified including a seat ramp. The three-point belt system had a generic adjustable load limiter. A pre-inflated driver airbag assembly was developed for the test fixture. Results of THOR test and simulations in different configurations will be presented. The configurations include different deceleration pulses. Further parameter variations are related to the restraint system including belt geometry and load limiter levels. Additionally different settings of the generic airbag were evaluated. The test set-up was evaluated and optimized in tests with the THOR-M dummy in different test configurations. Belt restraint parameters like D-ring position and load limiter setting were modified to provide moderate chest loading to the occupant. This resulted in dummy readings more representative of the loading in a contemporary vehicle than most available PMHS sled tests reported in the literature. However, to achieve a loading configuration that exposes the occupant to even less severe loading comparable to modern vehicle restraints it might be necessary to further modify the test set-up. The new generic sled test set-up and a corresponding CAE model were developed and applied in tests and simulations with THOR. Within the SENIORS project with this test set-up also volunteer and PMHS as well as HBM simulations are performed, which will be reported in other publications. The test environment can contribute in future studies to the assessment of existing and new frontal impact dummies as well as dummy improvements and related instrumentation. The test set-up and model could also serve as a new standard test environment for PMHS and volunteer tests as well as HBM simulations.
The case study "Digital Test Area Autobahn" is presented. A new built (September 2016) pre-stressed concrete bridge is equipped with different monitoring systems for the detection of traffic load, climatic influence and the reaction of the bridge. Possibilities for the implementation of a VoI (Value of Information) analyses are presented.
In future, additional and more detailed data are needed about the current conditions of bridges for preventive maintenance management. Monitoring procedures are not merely able to provide key performance indicators for a specific point in time, but also over a period. These KPIs must be selected in such a way as to permit substantiated statements about the present and future condition of bridges. For this reason, greater efforts must be made to define the significant KPIs for the various types of bridges, and show how these figures can be reliably determined. Both the COST Action TU1402, and TU1406 offer important approaches which, properly combined, can deliver substantial added value to the calculation and description of the condition of bridges in the interest of proactive maintenance management.
The levels of continuous vehicle automation have become common knowledge. They facilitate overall understanding of the issue. Yet, continuous vehicle automation described therein does not cover "automated driving" as a whole: Functions intervening temporarily in accident-prone situations can obviously not be classified by means of continuous levels. Continuous automation describes the shift in workload from purely human driven vehicles to full automation. Duties of the driver are assigned to the machine as automation levels rise. Emergency braking, e.g., is obviously discontinuous and intensive automation. It cannot be classified under this regime. The resulting absence of visibility of these important functions cannot satisfy " especially in the light of effect they take on traffic safety. Therefore, in order to reach a full picture of vehicle automation, a comprehensive approach is proposed that can map out different characteristics as "Principle of Operation" at top level. On this basis informing and warning functions as well as functions intervening only temporarily in near-accident situations can be described. To reach a complete picture, levels for the discontinuous, temporarily intervening functions are proposed " meant to be the counterpart of the continuous levels already in place. This results in a detailed and independent classification for accident-prone situations. This finally provides for the visibility these important functions deserve.
PROSPECT (Proactive Safety for Pedestrians and Cyclists) is a collaborative research project involving most of the relevant partners from the automotive industry (including important active safety vehicle manufacturers and tier-1 suppliers) as well as academia and independent test labs, funded by the European Commission in the Horizon 2020 research program. PROSPECT's primary goal is the development of novel active safety functions, to be finally demonstrated to the public in three prototype vehicles. A sound benefit assessment of the prototype vehicle's functionality requires a broad testing methodology which goes beyond what has currently been used. Since PROSPECT functions are developed to prevent accidents in intersections, a key aspect of the test methodology is the reproduction of natural driving styles on the test track with driving robots. For this task, data from a real driving study with subjects in a suburb of Munich, Germany was used. Further data from Barcelona will be available soon. The data suggests that intersection crossing can be broken down into five phases, two phases with straight deceleration / acceleration, one phase with constant radius and speed turning, and two phases where the bend is imitated or ended. In these latter phases, drivers mostly combine lateral and longitudinal accelerations and drive what is called a clothoid, a curve with curvature proportional to distance travelled, in order to change lateral acceleration smoothly rather than abrupt. The data suggests that the main parameter of the clothoid, the ratio distance travelled to curvature, is mostly constant during the intersections. This parameter together with decelerations and speeds allows the generation of synthetic robot program files for a reproduction of natural driving styles using robots, allowing a much greater reproducibility than what is possible with human test drivers. First tests show that in principle it is possible to use the driving robots for vehicle control in that manner; a challenge currently is the control performance of the robot system in terms of speed control, but it is anticipated that this problem will be solved soon. Further elements of the PROSPECT test methodology are a standard intersection marking to be implemented on the test track which allows the efficient testing of all PROSPECT test cases, standard mobile and light obstruction elements for quick reproduction of obstructions of view, and a concept for tests in realistic surroundings. First tests using the PROSPECT test methodology will be conducted over the summer 2017, and final tests of the prototype vehicles developed within PROSPECT will be conducted in early 2018
The UN Regulation No. 79 is going to be amended to allow automatically commanded steering functions (ACSF) at speeds above 10 km/h. Hence, requirements concerning the approval of automatically performed steering manoeuvres have to be set in order to allow safe use of automatic steering on public roads as well as improve overall road safety for the driver and the surroundings. By order of the German Federal Ministry of Transport and Digital Infrastructure (BMVI), BASt developed and verified physical test procedures for automatic steering to be implemented in UN Regulation No. 79. The usability of currently available test tools was examined. The paper at hand describes these test procedures and presents results from verification tests. The designated tests are divided in three sections: functionality tests, verifications for the transition of control and emergency tests. System functionality tests are auto matic lane keeping, automatic lane change and an automatic abort of an initiated lane change due to traffic. Those tests check if the vehicle remains in its lane (under normal operating conditions), is able to perform safe automatic lane change manoeuvres and if it considers other road users during its manoeuvres. Transition tests examine the vehicle's behaviour when the driver fails to monitor the system and in situations when the system has to hand over the steering control back to the driver. For instance these tests provoke driver-in-the-loop requests by approaching system boundary limitations, like missing lane markings, surpassing maximum lateral acceleration in a bend or even a major system failure. Even further the driver and his inputs are monitored and if the system detects that he is overriding system actions or contrary want to quit the driving task and unfastens the seat belt, it has to shut down and put the human back into manually control and the responsibility of driving. The last series of test consists of two emergency situations in which the system has to react to a time critical event: A hard decelerating vehicle and a stationary vehicle in front both with no lane change possibility for the ACSF vehicle. Some of the tests, especially the emergency manoeuvres, require special target vehicles and propulsion systems. Since no fully automatic steering vehicles are available, a current Mercedes E-Class with Mercedes' "drive pilot" system was used. It was shown that the vehicle is automatically able to brake to a full stop towards a static Euro NCAP target from partial-automatic driving at 90 km/h, that it could brake towards a rapidly decelerating lead vehicle when travelling at 70 km/h, that it was able during partially automatic driving to remain in its lane in normal operation conditions and to perform a automatic (driver initiated) lane change while surveilling the driver- activities.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschreiben. Das Ergebnis kann indes nicht zufriedenstellen: Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird hier, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschreiben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen. Dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
Europe has benefited from a decreasing number of road traffic fatalities. However, the proportion of older road users increases steadily. In an ageing society, the SENIORS project aims to improve the safe mobility of older road users by determining appropriate requirements towards passive vehicle safety systems. Therefore, the characteristics of road traffic crashes involving the elderly people need to be understood. This paper focuses on car occupants and pedestrians or cyclists in crashes with modern passenger cars. Ten crash databases and four hospital statistics from Europe have been analysed to answer the questions on which body regions are most frequently and severely injured in the elderly, and specific injuries sustained by always comparing older (65 years and above) with midâ€aged road users (25â€64 years). It was found that the body region thorax is of particularly high importance for the older car occupant with injury severities of AIS2 or AIS3+, where as the lower extremities, head and the thorax need to be considered for older pedestrians and cyclists. Further, injury risk functions were provided. The hospital data analysis showed less difference between the age groups. The linkage between crash and hospital data could only be made on a general level as their inclusion criteria were quite different.
Schutz von schwächeren Verkehrsteilnehmern: kommende Anforderungen aus Gesetzgebung und Euro NCAP
(2017)
Systeme der aktiven Fahrzeugsicherheit, insbesondere Notbremsassistenzsysteme und automatische Notbremssysteme, haben in den letzten zwei Dekaden große technische Fortschritte gemacht, und das im Wesentlichen ohne "Druck" von Gesetzgeber oder unabhängigen Testorganisationen " diese können aber durch passende Anforderungen den Vormarsch der Systeme in die Breite und die Ausnutzung von ansonsten für den Hersteller vielleicht nicht wirtschaftlichen Potentialen unterstützen. Dieser Bericht hat das Ziel, einen Überblick über die kommenden Anforderungen an Schutzsysteme für schwächere Verkehrsteilnehmer zu geben und diese Anforderungen in den Kontext Euro NCAP (=welchen Einfluss haben diese Anforderungen auf die Gesamtbewertung?) sowie Gesetzgebung (schwächere Anforderungen, aber dafür ein Markteintrittskriterium) zu stellen: - Anforderungen und Testprozeduren für Notbremsassistenz Fahrradunfälle 2018 und 2020 in Euro NCAP; - Anforderungen und Testprozeduren für Notbremsassistenz bei Nachtunfällen mit Fußgängern in Euro NCAP 2018; - Anforderungen und Testprozeduren für Abbiegeassistenzsysteme zum Schutz von Radfahrern in Unfallsituationen mit rechtsabbiegenden Lkw innerhalb der Fahrzeugtypgenehmigung.
Accidents between right turning trucks and straight driving cyclists often show massive consequences. Accident severity in terms of seriously or fatally injured cyclists that are involved is much higher than in accidents of other traffic participants in other situations. It seems clear that adding additional mirrors will very likely not improve the situation. At ESV 2015, a methodology to derive test procedures and first test cases as well as requirements for a driver assist system to address blind spot accidents has been presented. However, it was unclear if and how testing of these cases is feasible, to what extent characteristics of different truck concepts (e.g. articulated vehicles, rigid vehicles) influence the test conduction and outcome, and what tolerances should be selected for the different variables. This work is important for the acceptance of a draft regulation in the UN working group on general safety. In the meantime, three test series using a single tractor vehicle, a tractor-semitrailer combination and a rigid vehicle have been conducted. The test tools (e.g. surrogate devices) have been refined. A fully crashable, commercially available bicycle dummy has been tested. If used correct, this dummy does follow a straight line quite precisely and it does not cause any damage to the truck under test in case of accidental impact. The dummy specifications are freely available. During testing, the different vehicle categories resulted in different trajectories being driven. Articulated vehicle combinations did first execute a turn into the opposite direction, and on the other hand, single tractor vehicles did behave comparable to passenger cars. A possible solution to take these behaviors into account is to require the vehicles to drive through a corridor that is narrow for a precise straight-driving phase and extends during the turn. Other investigated parameters are the dummy and vehicle speed tolerances. The results from this research make it possible to draft a regulation for a driver assistance system that helps to avoid blind spot accidents: test cases have been refined, their feasibility has been checked, and corridors for the vehicles and for important parameters (e.g. test speeds) have been set. The test procedure is applicable to all types of heavy goods vehicles. In combination with the accidentology (ESV 2015 paper), the work provides the basis for a regulation for such an assistance system.
Advancing active safety towards the protection of vulnerable road users: the PROSPECT project
(2017)
Accidents involving Vulnerable Road Users (VRU) are still a very significant issue for road safety. According to the World Health Organisation, pedestrian and cyclist deaths account for more than 25% of all road traffic deaths worldwide. Autonomous Emergency Braking Systems have the potential to improve safety for these VRU groups. The PROSPECT project (Proactive Safety for Pedestrians and Cyclists) aims to significantly improve the effectiveness of active VRU safety systems compared to those currently on the market by expanding the scope of scenarios addressed by the systems and improving the overall system performance. The project pursues an integrated approach: Newest available accident data combined with naturalistic observations and HMI guidelines represent key inputs for the system specifications, which form the basis for the system development. For system development, two main aspects are considered: advanced sensor processing with situation analysis, and intervention strategies including braking and steering. All these concepts are implemented in several vehicle prototypes. Special emphasis is put on balancing system performance in critical scenarios and avoiding undesired system activations. For system validation, testing in realistic scenarios will be done. Results will allow the performance assessment of the developed concepts and a cost-benefit analysis. The findings within the PROSPECT project will contribute to the generation of state -of-the-art knowledge, technical innovations, assessment methodologies and tools for advancing Advanced Driver Assistance Systems towards the protection of VRUs. The introduction of a new generation safety system in the market will enhance VRU road safety in 2020-2025, contributing to the "Vision Zero" objective of no fatalities or serious injuries in road traffic set out in the Transport White Paper. Furthermore, the test methodologies and tools developed within the project shall be considered for the New Car Assessment Programme (Euro NCAP) future roadmaps, supporting the European Commission goal of halving the road toll in the 2011-2020 timeframe.
Für eine Reihe von EU Regelungen im Bereich Fahrzeugsicherheit erlaubt eine Verordnung bereits seit dem Jahr 2010 virtuelles Testen für die Typzulassungsprüfung. Technische Details bzw. konkrete Prozeduren für spezifische Regelungen sind in dieser Verordnung jedoch nicht enthalten. Das Hauptziel des europäischen Projekts IMVITER (lmplementation of Virtual Testing in Safety Regulations) war es, basierend auf der neuen Verordnung ein virtuelles Testverfahren auszuarbeiten und dabei offene Fragen zu berücksichtigen. Um die im Projekt-Konsortium unter Berücksichtigung der Anliegen aller Interessensgruppen wie Autohersteller, Zulassungsbehörden und technischer Dienste erarbeiteten offenen Punkte zu adressieren, wurde ein generisches Flussdiagramm entwickelt, das den Ablauf einer virtuell basierten Typprüfung darstellt. ln diesem Diagramm ist der virtuelle Typgenehmigungsprozess in drei aufeinander folgende Phasen aufgeteilt, die Verifikations-, Validierungs- und Typgenehmigungsphase. Von entscheidender Bedeutung ist die Phase der Validierung des Simulationsmodells, für die im IMVITER-Projekt eine Methodik vorgeschlagen wurde. Mit der im Projekt vorgeschlagenen Validierungsmethode ist kein Austausch des Simulationsmodells zwischen Fahrzeughersteller und technischem Dienst notwendig, so dass die Vertraulichkeit von Betriebsgeheimnissen nicht gefährdet ist. Zur Validierung des Modells werden jedoch immer Versuche notwendig sein. Dies gilt sowohl für die Überpruefung von passiven als auch aktiven Fahrzeugsicherheitssystemen. Eine zusammenfassende Betrachtung der Erfahrungen aus dem IMVITER-Projekt ergab, dass mit der Einführung von virtuellem Testen keine Erhöhung der Anforderungen an die Fahrzeugsicherheit bzgl. bestehender Regelungen verbunden sein sollte. Jedoch werden auch weiterhin neue zusäztliche Regelungen erforderlich sein, da sich das Unfallgeschehen und die Fahrzeugtechnologie weiterentwickeln und ändern werden. Diese sollten von Beginn an die Möglichkeiten des virtuellen Testens nutzen, insbesondere bei Testverfahren für neue Technologien, z.B. aktiver Fahrzeugsicherheitssysteme. Hier bieten virtuelle Testverfahren nicht nur eine Kosten- oder Zeitersparnis, sondern ermöglichen teilweise erst die sinnvolle Abprüfung von neuen Sicherheitssystemen, die mit aktuellen auf Hardware-Test basierenden Verfahren überhaupt nicht möglich wären.
Automatische Lenkfunktionen sind abgesehen von korrigierenden Lenkeingriffen entsprechend der UN-Regelung Nr. 79 bisher nur in einem Geschwindigkeitsbereich bis 10 km/h erlaubt. Die Weiterentwicklung der Technik im Bereich der Fahrerassistenzsysteme und der Automatisierung der Fahraufgabe wuerden es jedoch technisch erlauben, automatische Lenkfunktionen auch bei höheren Geschwindigkeiten einzusetzen. Neben einem Zugewinn an Komfort wird von diesen Systemen auch ein Beitrag zur Erhöhung der Verkehrssicherheit erwartet. Dieses Verkehrssicherheitspotenzial wird man jedoch nur ausschöpfen können, wenn die automatisierten Lenksysteme entsprechend gestaltet sind. Insbesondere sollten mögliche Risiken auf Grund automatischen Lenkens minimiert sein. Aus diesen Gründen laufen derzeit Arbeiten auf UNECE-Ebene, die Regelung Nr. 79 über einheitliche Bedingungen für die Genehmigung der Fahrzeuge hinsichtlich der Lenkanlage in Bezug auf automatische Lenkfunktionen (ACSF = Automatically Commanded Steering Functions) zu überarbeiten, um diese unter bestimmten Bedingungen auch bei höheren Geschwindigkeiten genehmigen zu können. Der vorliegende Beitrag reflektiert diese Arbeiten und stellt die Entwicklung der technischen Anforderungen an automatisches Lenken und der für die fahrzeugtechnischen Vorschriften vorgesehenen Testprozeduren dar.
Die Level kontinuierlicher Fahrzeugautomatisierung sind unter Fahrerassistenzexperten weithin bekannt und erleichtern das Verständnis. Sie können aber nicht Fahrzeugautomatisierung insgesamt zufriedenstellend beschreiben: Insbesondere temporär intervenierende Funktionen, die in unfallnahen Situationen eingreifen, können offensichtlich nicht nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben werden. Diese beschreiben nämlich die zunehmende Aufgabenverlagerung vom Fahrer zur maschinellen Steuerung bei zunehmendem Automatisierungsgrad. Notbremsfunktionen, beispielsweise, sind offensichtlich diskontinuierlich und nehmen zugleich auf intensive Weise Einfluss auf die Fahrzeugsteuerung. Sie lassen sich gerade nicht sinnvoll nach dem Level kontinuierlicher Fahrzeugautomatisierung beschrieben. Das Ergebnis kann indes nicht zufriedenstellen. Die fehlende Sichtbarkeit dieser Funktionen wird ihrer Bedeutung für die Verkehrssicherheit nicht gerecht. Daher wird im Beitrag, um ein vollständiges Bild der Fahrzeugautomatisierung zu erlangen, ein umfassender Ansatz zur Beschreibung verfolgt, der sich auf oberster Ebene nach Wirkweise unterscheidet. Auf dieser Basis lassen sich sowohl informierende und warnende Funktionen als auch solche, die nur temporär in unfallgeneigten Situationen intervenieren, im Detail beschrieben. Das ermöglicht es, eine eigenständige Klassifikation für unfallgeneigte Situationen zu erstellen; dies kann für diese wichtigen Funktionen die eigenständige Sichtbarkeit herstellen, die ihrer Bedeutung gerecht wird.
The presence and performance of Advanced Driver Assistance Systems (ADAS) has increased over last years. Systems available on the market address also conflicts with vulnerable road users (VRUs) such as pedestrians and cyclists. Within the European project PROSPECT (Horizon2020, funded by the EC) improved VRU ADAS systems are developed and tested. However, before determining systems" properties and starting testing, an up-to-date analysis of VRU crashes was needed in order to derive the most important Use Cases (detailed crash descriptions) the systems should address. Besides the identified Accident Scenarios (basic crash descriptions), this paper describes in short the method of deriving the Use Cases for car-to-cyclist crashes. Method Crashes involving one passenger car and one cyclist were investigated in several European crash databases looking for all injury severity levels (slight, severe and fatal). These data sources included European statistics from CARE, data on national level from Germany, Sweden and Hungary as well as detailed accident information from these three countries using GIDAS, the Volvo Cars Cyclist Accident database and Hungarian in-depth accident data, respectively. The most frequent accident scenarios were studied and Use Cases were derived considering the key aspects of these crash situations (e.g., view orientation of the cyclist and the car driver- manoeuvre intention) and thus, form an appropriate basis for the development of Test Scenarios. Results Latest information on car-to-cyclist crashes in Europe was compiled including details on the related crash configurations, driving directions, outcome in terms of injury severity, accident location, other environmental aspects and driver responsibilities. The majority of car-to-cyclist crashes occurred during daylight and in clear weather conditions. Car-to-cyclist crashes in which the vehicle was traveling straight and the cyclist is moving in line with the traffic were found to result in the greatest number of fatalities. Considering also slightly and seriously injured cyclists led to a different order of crash patterns according to the three considered European countries. Finally the paper introduced the Use Cases derived from the crash data analysis. A total of 29 Use Cases were derived considering the group of seriously or fatally injured cyclists and 35 Use Cases were derived considering the group of slightly, seriously or fatally injured cyclists. The highest ranked Use Case describes the collision between a car turning to the nearside and a cyclist riding on a bicycle lane against the usual driving direction. A unified European dataset on car-to-cyclist crash scenarios is not available as the data available in CARE is limited, hence national datasets had to be used for the study and further work will be required to extrapolate the results to a European level. Due to the large number of Use Cases, the paper shows only highest ranked ones.
Unter bestimmten Voraussetzungen sind im Zuge der quantitativen Sicherheitsbewertung von Straßentunneln Risikoanalysen durchzuführen. Neben objekt-, verkehrs- oder ereignisspezifischen Parametern gibt es auch etliche Eingangsparameter, die fest im Risikomodell hinterlegt sind und deren Variation für gewöhnlich nicht vorgesehen ist. Dies trifft auch für Parameter des menschlichen Verhaltens zu. Im Zuge von Versuchsreihen zum Flucht- und Reaktionsverhalten der Verkehrsteilnehmer im Ereignisfall in Straßentunneln wurden verschiedene Verhaltensparameter ermittelt und analysiert, die den konventionellen Modell-Basisparametern erstmals im Österreichischen Tunnelrisikomodell (TuRisMo) gegenübergestellt werden. Als Ergebnis kann auf Basis der aktuell gewonnenen Verhaltensparameter eine Senkung des Gesamtrisikos aufgezeigt werden, dessen Einordnung im folgenden Beitrag diskutiert wird.
A reduction of around 48% of all road fatalities was achieved in Europe in the past years including a reduced number of fatalities with an older age. However, among all road fatalities, the proportion of elderly is steadily increasing. In an ageing society, the European (Horizon2020) project SENIORS aims to improve the safe mobility of older road users, who have different transportation habits compared to other age groups. To increase their level of safe mobility by determining appropriate requirements for vehicle safety systems, the characteristics of current road traffic collisions involving the elderly and the injuries that they sustain need to be understood in detail. Hereby, the paper focuses on their traffic participation as pedestrian, cyclist or passenger car occupant. Following a literature review, several national and international crash databases and hospital statistics have been analysed to determine the body regions most frequently and severely injured, specific injuries sustained and types of crashes involved, always comparing older road users (65 years and more) with mid-aged road users (25-64 years). The most important crash scenarios were highlighted. The data sources included European statistics from CARE, data on national level from Germany, Sweden, Italy, United Kingdom and Spain as well as in-depth crash information from GIDAS (Germany), RAIDS (UK), CIREN and NASS-CDS (US). In addition, familiar hospital data from Germany (TraumaRegister DGU-®), Italy (Italian Register of Acute Traumas) and UK hospital statistics (TARN) were included in the study to gain further insight into specific injury patterns. Comprehensive data analyses were performed showing injury patterns of older road users in crashes. When comparing with mid-aged road users, all databases showed that the thorax body region is of particularly high importance for the older car occupant with injury severities of AIS 2 or AIS 3+, whereas the body regions lower extremities, head and thorax need to be considered for the older pedestrians and cyclists. Besides these comparisons, the most frequent and severe top 5 injuries were highlighted per road user group. Further, the most important crash configurations were identified and injury risk functions are provided per age group and road user group. Although several databases have been analysed, the picture on the road safety situation of older road users in Europe was not complete, as only Western European data was available. The linkage between crash data and hospital data could only be made on a general level as their inclusion criteria were quite different.
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.
Test and assessment procedures for passive pedestrian protection based on developments by the European Enhanced Vehicle-safety Committee (EEVC) have been introduced in world-wide regulations and consumer test programmes, with considerable harmonization between these programmes. Nevertheless, latest accident investigations reveal a stagnation of pedestrian fatality numbers on European roads running the risk of not meeting the European Union- goal of halving the number of road fatalities by the year 2020. The branch of external road user safety within the EC-funded research project SENIORS under the HORIZON 2020 framework programme focuses on investigating the benefit of modifications to pedestrian test and assessment procedures and their impactors for vulnerable road users with focus on the elderly. Injury patterns of pedestrians and cyclists derived from the German In-Depth Accident Study (GIDAS) show a trend of AIS 2+ and AIS 3+ injuries getting more relevant for the thorax region in crashes with newer cars (Wisch et al., 2017), while maintaining the relevance for head and lower extremities. Several crash databases from Europe such as GIDAS and the Swedish Traffic Accident Data Acquisition (STRADA) also show that head, thorax and lower extremities are the key affected body regions not only for the average population but in particular for the elderly. Therefore, the SENIORS project is focusing on an improvement of currently available impactors and procedures in terms of biofidelity and injury assessment ability towards a better protection of the affected body regions, incorporating previous results from FP 6 project APROSYS and subsequent studies carried out by BASt. The paper describes the overall methodology to develop revised FE impactor models. Matched human body model and impactor simulations against generic test rigs provide transfer functions that will be used for the derivation of impactor criteria from human injury risk functions for the affected body regions. In a later step, the refined impactors will be validated by simulations against actual vehicle front-ends. Prototyping and adaptation of test and assessment procedures as well as an impact assessment will conclude the work of the project at the final stage. The work will contribute to an improved protection of vulnerable road users focusing on the elderly. The use of advanced human body models to develop applicable assessment criteria for the revised impactors is intended to cope with the paucity of actual biomechanical data focusing on elderly pedestrians. In order to achieve optimized results in the future, the improved test methods need to be implemented within an integrated approach, combining active with passive safety measures. In order to address the developments in road accidents and injury patterns of vulnerable road users, established test and assessment procedures need to be continuously verified and, where needed, to be revised. The demographic change as well as changes in the vehicle fleet, leading to a variation of accident scenarios, injury frequencies and injury patterns of vulnerable road users are addressed by the work provided by the SENIORS project, introducing updated impactors for pedestrian test and assessment procedures.
Folgen der StVO-Änderung für das Verkehrsverhalten von Kraftfahrern beim Auftreten von Kindern
(1983)
Eine der im Jahre 1980 vorgenommenen Änderungen der Straßenverkehrsordnung (StVO) bezieht sich auf das Verhalten der Fahrzeugführer gegenüber Kindern, Hilfsbedürftigen und älteren Menschen. Danach sind die Fahrzeugführer gehalten, sich insbesondere durch Verminderungen der Fahrgeschwindigkeit und durch Bremsbereitschaft so zu verhalten, dass eine Gefährung dieser Verkehrsteilnehmer ausgeschlossen ist. In einem Versuch wurde der Frage nachgegangen, ob im Fahrverhalten der Kraftfahrer im Sinne der StVO-Vorgaben Veränderungen eingetreten sind. Neben Beobachtungen des Gesamtverkehrs wurden ausgedehnte Testfahrten mit Versuchspersonen sowie Befragungen durchgeführt. Die Ergebnisse zeigen, dass die erwähnte Änderung der StVO sich bisher im praktischen Fahrverhalten kaum niedergeschlagen hat. An den Kindern am Straßenrand wurde mit relativ hoher Geschwindigkeit (im Mittel knapp unter 50 km/h) vorbeigefahren, wobei eine systematische Bremsbereitschaft nicht zu erkennen war. Die Befragung von Fahrzeugführern ergab, dass Unklarheiten darüber bestehen, welche Geschwindigkeit für Begegnungen mit Kindern angemessen sei. Für wünschenswert gehalten wurde eine Präzisierung eines Geschwindigkeitslimits. Abgesehen davon wurde festgestellt, dass die Neuregelungen der StVO inhaltlich noch kaum bekannt waren. Für das weitere Vorgehen erscheint es vorteilhat, aus Gründen der Eindeutigkeit und Einfachheit die Angaben von Höchst- oder Orientierungswerten in Erwägung zu ziehen. Wichtig erscheint, die Dominanz der derzeitigen innerörtlichen Höchstmarke "Tempo 50" abzubauen und auch niedrigere Höchstgeschwindigkeiten mit gleichem Stellenwert ins Bewusstsein zu rücken.
Nach grundsätzlichen Einführungsüberlegungen wird zunächst die Frage der Akzeptanz und die Notwendigkeit, bei der Entwicklung und Erprobung von Maßnahmen, Vertreter der Erziehungsinstanzen möglichst frühzeitig und umfassend zu beteiligen, angesprochen. Diese Forderung einer engen Abstimmung und Zusammenarbeit von Forschungspraxis, Umsetzungspraxis und Erziehungspraxis gilt auch für die Entwicklung, die Erprobung, die Umsetzung, die anschließenden Wirksamkeitskontrollen, die Interpretation der Ergebnisse und die Auswahl der die weitere Umsetzung korrigierenden Informationen. Im folgenden werden zwei weitere wichtige Wirksamkeitsbedingungen ausführlicher behandelt: die Entwicklungsorientierung und der Situationsbezug, d.h. die Orientierung der Maßnahme an der Umgebung des Kindes, die als konkrete Verkehrswirklichkeit den Raum bildet, in dem das Kind lebt und aufwächst. Als konkrete Beispiele für das ineinandergreifen deduktiv theoretischer Ableitungen und praktischer Erfahrungen bei der Entwicklung von verkehrspädagogischen Maßnahmen werden das Programm "Kind und Verkehr", der Kinderverkehrsclub, das Entwicklungsprojekt "Verkehrserziehung im Kindergarten" erwähnt. Als mehr formale Bedingungen, die für die Wirksamkeit einer Maßnahme wichtig sind, werden deren Kontinuität, aber auch grundsätzliche Veränderbarkeit herausgearbeitet.
Es wird über ein Schulungsprogramm referiert, das von einer Expertengruppe entwickelt wurde und der Entdeckung von unter Drogen stehenden Kraftfahrern durch Polizeibeamte dient. Die Expertengruppe setzte sich aus Verkehrs- und Rechtsmedizinern, Toxikologen, Ärzten, Juristen und Polizeischulungsbeamten zusammen. Die Verbreitung des Schulungsprogramms wird über Multiplikatorenseminare und Praxisseminare erfolgen. Inhalte des Schulungsprogramms sind Epidemiologie, Rechtsfragen, Drogenwirkungen, Stoffkunde, Verdachtsgewinnung und Beweissicherung. Die Expertengruppe konzipierte einen Protokollbogen für polizeiliche Beobachtungen, die viele Punkte aus den bereits vorhandenen Protokollen zur Feststellung von Trunkenheitsfahrten enthalten. Zusätzlich sind Beobachtungen der Augenbindehäute, des Durchmessers und der Reaktion der Pupillen aufgeführt. Außerdem wird nach Änderungen des Verhaltens während der polizeilichen Maßnahme gefragt. In den Multiplikatorenseminaren geht es um die Ausbildung der Dozenten, die das gewonnene Wissen in Praxisseminaren an Kollegen weitergeben. Es wurden bereits Pilotveranstaltungen durchgeführt.
In Deutschland werden als passive Schutzeinrichtungen an Straßen Stahlschutzplanken und in jüngerer Zeit auch vermehrt Betonschutzwände eingesetzt. Auf dem Gebiet der Schutzeinrichtungen wird es demnächst europäisch harmonisierte Normen geben. Durch ihre Einführung, vermutlich noch in 1997, kommt es auch in Deutschland zur Veränderung der Anforderungen an Schutzeinrichtungen. Die Qualifizierung der in Deutschland nach den Richtlinien für passive Schutzeinrichtungen an Straßen eingesetzten Schutzeinrichtungen nach den europäischen Vorgaben ist durch die Bundesanstalt für Straßenwesen (BASt) in einem Forschungsprojekt für das Bundesverkehrsministerium erfolgt. Die BASt hat ein weiteres Projekt initiiert mit dem Ziel, die wichtigsten Ausführungsformen zu untersuchen und zu weitergehenden Kenntnissen über die hier eingesetzten Schutzeinrichtungen zu kommen. Berichtet wird über wesentliche Ergebnisse aus diesem Projekt.
A sociological perspective on different strategies of reward in urban traffic law enforcement
(1996)
In order to enhance road safety, it is necessary to make road users change their behaviour. There are two forms of police enforcement: punishment for breaking traffic regulations and rewards for rule-conformist behaviour. Punishment does not appear to produce long term changes. There are two main reward strategies: individual and group dependent rewards. Individuals who are members of a clearly defined group have good prospects of winning prizes in a lottery. The strategy of the delegated group dependent reward is based on a donation to a social institution. Traffic safety is a conflict of interests, and game theory considerations can be applied. Results of German and Dutch studies confirm hypotheses based on the game theory concept. Traffic behaviour mostly depends on expectation of others' behaviour. Successful strategies of reward should always be based on individual settlements of the rewards. More investigations are needed. Strategies of group dependent reward are not recommended. The size of reward and probability of winning it should be linked to rate of participation: the greater the participation, the greater the value of reward and probability of winning it. Every driver has a threshold from which he is prepared to change his traffic behaviour for a reward.
Aus Erfahrungen mit Untersuchungen zum Einsatz ortsfester Anlagen zur Geschwindigkeitsüberwachung werden für die künftige Forschung einige Forderungen erhoben. Die Erkenntnisse aus der Forschung zur Verbesserung der Verkehrssicherheit durch bauliche oder verkehrstechnische Maßnahmen sollten zur Optimierung des Einsatzes solcher Anlagen genutzt werden. Es wird dafür plädiert zu untersuchen, welche Standorte beim Einsatz ortfester Anlagen eine möglichst linienhafte Wirkung zu erzielen in der Lage sind. Insgesamt wird die Erarbeitung eines Kriterienkatalogs angeregt, der den jeweiligen Entscheidungsträgern bei der Planung und Aufstellung der Anlagen behilflich sein kann. Da ortsfeste Anlagen eine lediglich ortsspezifische Geschwindigkeitsanpassung bewirken, wird die Kombination ortsfester mit mobilen Kontrollen auf Landstraßen empfohlen. Es sollte auch untersucht werden, ob die Verkehrsüberwachung durch ortsfeste Anlagen nicht nur ein Beitrag zur Reduzierung von Geschwindigkeiten darstellt, sondern auch dazu beitragen kann, Überholunfälle zu reduzieren.
Wegweisung auf Autobahnen
(2001)
Die Wegweisung im Straßenverkehr hat verschiedene Aufgaben zu erfüllen. Der Wegweisung auf Autobahnen kommt dabei aufgrund des hohen Anteils an ortsunkundigen Kraftfahrern eine besondere Bedeutung zu. Im Beitrag werden zentrale Aspekte zur Wegweisung näher erläutert. Unter anderem sind dies Lesbarkeit, Gestaltung der Beschilderung, Verständlichkeit, Erkennbarkeit, Systematik etc. Anhand der Beschilderung an einer Anschlussstelle werden diese Aspekte konkret erläutert.
Es werden verschiedene Einflussfaktoren auf der Basis neuerer empirischer Befunde in ihrer Relevanz zur Erklärung regelkonformen wie -abweichenden Verkehrsverhaltens erörtert. Sanktionsschwere und Sanktionswahrscheinlichkeit (Entdeckungswahrscheinlichkeit) sind in ihrer Wirkung insofern verbunden, als eine hohe Strafe keine Abschreckung bewirkt, wenn die Wahrscheinlichkeit einer Entdeckung minimal ist. Im Umkehrschluss gilt, dass eine hohe Entdeckungswahrscheinlichkeit nur bei einer bedeutsamen Sanktion von abschreckender Wirkung ist. Für das Verhalten sind eher Wahrnehmungen und Bewertungen der Betroffenen ausschlaggebend und weniger die objektiven Gegebenheiten, zum Beispiel die tatsächliche Überwachungsintensität beziehungsweise die Sanktionsschwere. Neben dem Einflussfaktor Unmittelbarkeit der Sanktionierung werden die unterstützende Wirkung von positiven Einstellungen, bauliche Veränderungen des Fahrraums und fahrzeugtechnische Entwicklungen diskutiert. Für die Erforschung der Abhängigkeit verschiedener Faktoren in ihrer Wirkung auf das Verhalten von Verkehrsteilnehmern wird die Theorie der Befolgung von Gesetzen von Opp in ihrer Modifikation von Diekmann favorisiert.
Im Zeitraum 1991/92 wurde in 15 europäischen Ländern eine Vergleichsstudie zu den Einstellungen und Meinungen von Autofahrern durchgeführt (das sogenannte SARTRE-Projekt). Anhand der dabei erhobenen Daten wurden Sekundäranalysen zur Altersgruppe der 18- bis 24-jährigen Autofahrer vorgenommen. Die Sekundäranalysen beruhen auf deskriptiven Vergleichen der Altersgruppen in den verschiedenen europäischen Ländern und varianzanalytischen Berechnungen. Wenn diese Berechnungen zu eher geringen Varianzaufklärungen geführt haben, ist dies auch in der schlechten Anpassung der abhängigen Variablen an der Normalverteilung begründet. Kleinere Effekte, vor allem die berichteten Interaktionseffekte, sind daher auch bei Vorliegen signifikanter Werte nur mit Vorbehalt zu interpretieren. Insgesamt lassen die Ergebnisse der Sekundäranalysen folgende Aussagen zum jungen Fahrer zu: 1. Junge Fahrer machen in den einzelnen europäischen Ländern unterschiedliche Anteile an den jeweiligen Fahrerpopulationen aus. Auch der Anteil der Frauen unter den jungen Fahrern schwankt beträchtlich. Bereits unter Berücksichtigung dieser beiden soziodemografischen Basismerkmale ergeben sich für die Verkehrssicherheitsarbeit in Europa unterschiedliche Gewichtungen. Der Anteil junger männlicher Fahrer ist besonders groß in den südeuropäischen Ländern. 2. Bei den meisten Meinungs- und Einstellungsfragen ist die Variabilität im Antwortverhalten zwischen den Fahrerpopulationen der Länder größer als die Variabilität der Altersgruppen innerhalb der Länder. Dies gilt insbesondere für den Themenkomplex "Sicherheitsgurt", mit Abstrichen auch für das Problemfeld "Alkohol und Fahren". Das Antwortverhalten der jungen Fahrer liegt hier in aller Regel im Trend nationaler Gewohnheiten und weicht nicht auffällig von den Meinungen und Einstellungen der übrigen Fahrer im eigenen Land ab. 3. Bei denjenigen Fragen, die die Einstellung zu geschwindigkeitsorientiertem und regelabweichendem Fahrverhalten und das damit verbundene Risiko betreffen, ist die Variabilität der Altersgruppen meist größer als die der Länderstichproben insgesamt. Die Bereitschaft, das - meist unterschätzte - Risiko hoher und regelabweichender Fahrgeschwindigkeiten einzugehen, scheint junge Fahrer - insbesondere junge männliche Fahrer - in Europa zu verbinden. Dieses Ergebnis der Sekundäranalyse ist sicher nicht überraschend, könnte aber eine inhaltliche Ausrichtung liefern, wenn es darum geht, europaweite Aufklärungsmaßnahmen für junge Fahrer in die Wege zu leiten.
The field of safety in road tunnels has always been an important issue for operators, owners and the responsible authorities. After the tunnel accidents in 1999 the subject gained however in importance. On European level the Directive 2004/54 EC on "Minimum safety requirements for tunnels in the Trans European Road network" has been published. This guideline has to be implemented into national law by all Member States. According to the guideline all Member States of the European Community shall develop a methodology for risk analyses to be applied in certain cases. For Germany, a standardized methodology for a probabilistic quantitative risk assessment has been worked out.
A very high service availability is important for the operator and for the user of road tunnels, too. The service availability of a structure is directly related to its quality. The earlier quality assurance measures are being considered during the life cycle, the better a structure of high quality can be guaranteed. Problems which occur during the operation period of a structure often result from design errors or from inadequate realisation during the construction phase. They may also occur as a result of wrongly planned maintenance and refurbishment works. Thus, the transfer of specific data, information and experiences through the whole life cycle is very important. In this context methods of facility management can provide efficient assistance when they have already been used throughout all three classic phases of a structure's life cycle - planning, construction and operation. Finally the tunnel drainage system of German road tunnels is considered as an example as practical application possibility.
Im Rahmen eines von der Bundesanstalt für Straßenwesen (BASt) initiierten Forschungsvorhabens (15.449/2007/ERB: "Prüfverfahren zur Beurteilung der Lebensdauer von Kunststoffdichtungsbahnen für Straßentunnel") wurden anhand von Untersuchungen an Kunststoffdichtungsbahnen (KDB) auf Basis von Polyolefinwerkstoffen die Möglichkeiten der Beurteilung der oxidativen Langzeitbeständigkeit sondiert. Im Mittelpunkt stand die Erprobung des Autoklaventests in Anlehnung an DIN EN ISO 13438 (Methode C1/C2) an ausgewählten, für den Tunnelbau repräsentativen marktüblichen KDB-Produkten. Die Untersuchungen im Autoklaven bei erhöhten Temperaturen (60 -°C, 70 -°C und 80 -°C) und Sauerstoffdrücken (11, 21 und 51 bar) wurden durch vergleichende Versuche im Wärmeschrank (Ofen) bei erhöhter Temperatur (85 -°C) in Anlehnung an DIN EN 14575 ergänzt. Die KDB-Produkte wurden außerdem einer eingehenden Materialcharakterisierung (Zugprüfung, OMA, DSC) unterzogen. Weiterhin wurden Bauwerksdaten recherchiert und auf ihre Nutzbarkeit zur Bewertung und Prüfbarkeit der Langzeitbeständigkeit von KDB in Tunneln betrachtet. Ziel war auch, die Anwendbarkeit des bisher vorgeschlagenen Extrapolationsmodells zur Auswertung der Ergebnisse von Autoklaventests an im Tunnelbau marktüblichen Produkten für Nutzungsdauern über 25 Jahre zu überprüfen und zur Entwicklung eines geeigneten Prüfverfahrens beizutragen. Der Beitrag geht auf Ergebnisse des Vorhabens ein und zeigt erste Schlussfolgerungen und weiteren Untersuchungsbedarf auf. Die Ergebnisse werden in den "Empfehlungen zu Dichtungssystemen im Tunnelbau EAG-EDT" des Arbeitskreises 5.1 "Kunststoffe in der Geotechnik und im Wasserbau" berücksichtigt, deren 2. Auflage in Vorbereitung ist. Aspekte des thermischen Verhaltens der eingesetzten Werkstoffe sowie mögliche Anpassungen der Prüfrandbedingungen für die Autoklaventests werden ergänzt und Hinweise zur Interpretation von Prüfergebnissen gegeben. Außerdem wurden inzwischen ausgehend von den Ergebnissen des Forschungsvorhabens erste Autoklaven-Ringversuche in drei Prüfinstitutionen initiiert.
This paper deals with the determination of test criteria for the durability assessment of polyvinyl chloride (PVC)-based geosynthetic barriers (GBR-P) products in tunnel sealing systems. In the project different products for road tunnel application are investigated by systematic long time storage in hot water using a new test procedure based on SIA V 280 standard (test no. 13) and EN 14415. The objective of this research project is to derive suitable exposure conditions and criteria for a practical testing procedure with regard to service lifetimes of up to 100 years. For that test temperature and time as well as the best suitable test medium have been investigated in a structured way. To verify the results of the new test procedure the material properties of GBR-P samples removed from older road tunnels are investigated. Based on the presented results of the still on-going research program some preliminary conclusions regarding the updating of the German regulations for road tunnel sealing systems (ZTV-ING part 5 section 5 and TL/TP KDB) are given.
Straßentunnel mit integriertem Rettungsweg: Konstruktions- und betriebliche Sicherheitsaspekte
(2009)
Infolge der seit 2003 in den RABT formulierten schärferen Sicherheitsanforderungen ist für Gegenverkehrstunnel bei Neuplanungen und bautechnischen Nachrüstungen häufig die Anordnung eines parallel zur Hauptröhre verlaufenden Rettungsstollens erforderlich. Untersuchungen der Bundesanstalt für Straßenwesen (BASt) zur Wirtschaftlichkeit verschiedener aktueller und auch neuer Querschnittsvarianten haben gezeigt, dass insbesondere ein Querschnitt mit integriertem begehbarem Rettungsweg unter bestimmten Voraussetzungen Kostenvorteile gegenüber der Regellösung mit parallelem Rettungsstollen bietet. In ergänzenden Untersuchungen wurden konstruktive und sicherheitstechnische Detailfragen für einen Regelquerschnitt mit integriertem Rettungsweg untersucht und bewertet und ein Kostenvergleich mit der Regellösung mit parallelem Rettungsstollen wurde durchgeführt.
Tunnel in Spritzbetonbauweise werden in der Regel mit einem Abdichtungssystem aus Kunststoffdichtungsbahnen (KDB) gegen das anstehende Bergwasser abgedichtet. Die Tunnelabdichtungen aus KDB müssen dabei über die gesamte Nutzungsdauer des Bauwerks von in der Regel 130 Jahren zuverlässig ihre Funktion erfüllen. Ein einfacher Austausch der KDB oder der Einbau einer gleichwertigen Alternative ist in der Regel nicht, oder nur mit erheblichem Aufwand möglich. Bislang existieren national und international keine abgesicherten Prüfkriterien, die eine Bestimmung der Langzeitbeständigkeit von KDB über die geforderte Nutzungsdauer von mindestens 100 Jahren ermöglichen. Im vorliegenden Beitrag werden Untersuchungsergebnisse eines BASt Forschungsprojektes präsentiert, in dem Prüfkriterien für die Abschätzung der Langzeitbeständigkeit von KDB aus PVC-P hergeleitet werden. In diesem Projekt werden verschiedene marktübliche KDB für die Tunnelabdichtung mit einem beschleunigten Prüfverfahren "Lagerung in heißem Wasser" systematisch auf ihr Alterungsverhalten hin untersucht. Das hierfür verwendete Immersionsprüfverfahren wurde neu entwickelt und basiert auf der SIA V 280 (Prüfung Nr. 13) und DIN EN 14415. Ziel der Untersuchungen ist es, die erforderlichen Prüfkriterien zu definieren, die für eine praxisgerechte Abschätzung der Nutzungsdauer von mindestens 100 Jahren erforderlich sind. Hierfür werden beispielsweise die Einlagerungsdauer, die Einlagerungstemperatur und das Prüfmedium strukturiert untersucht. Zum Vergleich der Prüfergebnisse aus dem Immersionsprüfverfahren werden Untersuchungen an ausgebauten KDB Proben aus 2 älteren Straßentunneln herangezogen. Die Ergebnisse des Forschungsvorhabens sollen in die Fortschreibung des nationalen Regelwerks für den Straßentunnelbau (TL/TP KDB) einfließen.
Untersuchungen an in situ gealterten Kunststoffdichtungsbahnen aus Abdichtungen von Straßentunneln
(2011)
Tunnel in Spritzbetonbauweise werden in der Regel mit einem Abdichtungssystem aus Kunststoffdichtungsbahnen (KDB) gegen das anstehende Bergwasser abgedichtet. Zur Gewährleistung der Dauerhaftigkeit und Gebrauchstauglichkeit aber auch der Verkehrssicherheit (z.B. Gefahr der Glatteisbildung in undichten Tunneln) müssen die Tunnelabdichtungen aus KDB dabei über die gesamte Nutzungsdauer des Bauwerks von in der Regel 100 Jahren zuverlässig Ihre Funktion erfüllen. An der Entwicklung von Prüfverfahren zum Nachweis dieser Nutzungsdauer wird zurzeit national und international intensiv geforscht. Zur Verifizierung und Kalibrierung dieser Prüfverfahren können Untersuchungen an in situ gealterten KDB-Proben aus bestehenden Straßentunneln sehr nützlich sein. Im vorliegenden Beitrag werden erste Ergebnisse der Untersuchungen zu Materialeigenschaften von ausgebauten KDB Proben aus älteren Straßentunneln vorgestellt. Im Rahmen eines Forschungsprojektes der Bundesanstalt für Straßenwesen (BASt) wurden bereits zahlreiche Materialproben aus bestehenden Straßentunneln, die aktuell bautechnisch nachgerüstet werden, entnommen und untersucht. Bei der Entnahme der KDB-Proben wurde parallel auch die Bergwassertemperatur gemessen und an Bergwasserproben der Chemismus analysiert. Soweit möglich wurden die Produktdaten des Anlieferungs- bzw. Einbauzustandes beim Hersteller oder Bauherrn recherchiert, um so die Veränderungen der mechanischen Eigenschaften durch die in situ Alterung bewerten zu können. Die ermittelten mechanischen Eigenschaften nach Alterung wurden mit den Anforderungen damals gültiger und aktueller Regelwerke verglichen.
The Federal Highway Network of Germany represents considerable fixed assets. Construction and maintenance activities not only require a high budget, but also influence the traffic infrastructure and, thus, the economy and society as a whole. The present safety of the network has to be ensured under consideration of environmental aspects. At the same time the network owner has to make sure that the civil works are carried out in the most efficient way. Considering the fact that financial resources are restricted, the costs have to be spent in a way to obtain the greatest possible benefit. This task is supported by the application of a comprehensive Asset Management, which is subdivided into operational and controlling tasks respectively. The paper describes the current management procedures.
Allein im Netz der Bundesfernstraßen sind etwa 35.000 Brücken mit einer Fläche von 25 Millionen Quadratmetern enthalten. Ihr Wiederbeschaffungswert beträgt etwa 70 Milliarden DM. Es wird über die notwendigen Aktivitäten zur Erhaltung dieser für die Aufrechterhaltung des auf den Bundesfernstraßen rollenden Verkehrs besonders wichtigen Bauwerke berichtet. Aufgrund des weiter stärker werdenden Verkehrs, der zunehmenden Fahrzeuggewichte sowie der wachsenden Anzahl von Schwertransporten unterliegen insbesondere die älteren Bauwerke größerer Beanspruchung, als man bei ihrer Planung in Rechnung stellen musste. Hinzu kommt die natürliche Alterung aus sonstigen äußeren Einflüssen wie Temperatur, Witterung und erhöhter Umweltbelastung. Die Verwendung von Auftausalzen führt insbesondere bei älteren Brückenüberbauten zu Korrosionsschäden an der Bewehrung des Betons. Durch die Entwicklung eines Bauwerks-Management-Systems (BMS) wird die Verbesserung der Erhaltung von Brücken und sonstigen Ingenieurbauten angestrebt. Der Aufbau und die Wirkungsweise des BMS werden dargelegt. Des Weiteren werden die schon seit langem eingeführten Prüfvorschriften für Bauwerke im Zuge von Straßen und Wegen (DIN 1076) sowie gängige Prüfverfahren beschrieben.
BMS-Entwicklungen
(2002)
The Federal Ministry of Transport, Building and Housing is aiming for a comprehensive Management System taking into account state-specific and federal requirements as well as existing regulations in the frame of maintenance planning. The system is subdivided into three processes, each comprising special tools for valuation, analysing and planning. Some of the sub-modules have already been realised, eg the database at state level, the inspection procedure in combination with the procedures of damage and condition assessment and the estimation of future maintenance costs at federal level. Other sub-modules are currently being prepared, eg tools for evaluation and selection of measures. However, a large portion of the essential issues are still in the planning phase, eg program creation by taking restrictions into account. The realisation of the complete Management System will be finished by the year 2005.
The first stage of the work has been to collate information on bridge assessment from the participating countries. In the later stages, the aim is to provide guidelines that reflect the current best practices, a methodology that will allow for future development and sufficient flexibility to accommodate variations in national priorities as the process of harmonisation is pursued. The following tasks fall within the scope of the project: (1) a review of current procedures and standards used for bridge assessment in Europe; (2) the development of models for taking into account the bridge specific traffic conditions and material properties; (3) the use of reliability methods based on a probabilistic approach for bridge assessment including the use of measurements for updating the reliability of structural elements; and (4) the provision of recommendations for methods and procedures that can be adopted for the assessment module of the management framework highlighting where further development will be beneficial.
Brückenmanagement
(2001)
Die systematische Erhaltung der Brücken im Zuge der Bundesfernstraßen ist eine wichtige Aufgabe für den Baulastträger Bund und die Straßenbauverwaltungen der Länder. Um künftig Erhaltungsprogramme auf einer einheitlichen Grundlage unter Berücksichtigung gesamtwirtschaftlicher Grundsätze aufstellen zu können, wird durch die Bundesanstalt für Straßenwesen derzeit im Auftrag des Bundesministeriums für Verkehr, Bau- und Wohnungswesen ein umfassendes Bauwerks-Management-System (BMS) konzipiert und realisiert. Das geplante BMS beinhaltet alle Funktionen zur Durchführung des Erhaltungsmanagements. Grundlage ist die Erhebung und Bereitstellung von objektbezogenen Informationen. In Verbindung mit netzbezogenen Daten, Rahmenbedingungen und Restriktionen wird damit die Basis für Analyseprozesse, zum Beispiel Wirtschaftlichkeitsuntersuchungen, Priorisierungen und Bedarfsermittlungen bereitgestellt. Als Ergebnis werden Maßnahmenvorschläge, optimierte Programmplanungen und Angaben zum Finanzbedarf entwickelt. Verfahren und Programmsysteme werden schrittweise ab 2002 bis 2005 den Straßenbauverwaltungen zur Verfügung gestellt.
Germany's road infrastructure grew over centuries to become the arteries and lifelines of our society. The present safety of the infrastructure has to be ensured under consideration of environmental aspects. At the same time the owner has to make sure that the maintenance activities are carried out in the most efficient way. Considering the fact that financial resources are restricted, maintenance costs have to be spent in a way to obtain the greatest possible benefit. In the case of bridges, which are one of the most important parts of the road infrastructure in Germany, this task is supported by the application of a bridge management system (BMS). The existing German BMS contains assessment and optimization procedures on object and network level and is the basis for advancements to meet future demands. Developments concern life cycle and quality-oriented, holistically optimized procedures. Reasonable infrastructure management will contribute to meeting efficiency and sustainability objectives and to achieving interoperability. Here holistic network infrastructure management methods are required. There is a strong need for management solutions during the whole service life of a structure. The definition of criteria for evaluation of the relevance of failure mechanisms, including acceptance thresholds, requires the availability of relevant data for management procedure. Tools for innovative investigation methods and an effective data management will help in meeting the requirements. Relevant fields of research are improved maintenance strategies to meet future demands concerning heavy goods traffic, application and further development of nondestructive testing methods for efficient and sustainable management structures, and the improvement of analytic management tools to meet future demands.
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
Das Unfallgeschehen der Radfahrer wird analysiert. Ein erheblicher Anteil der Unfälle ereignet sich ohne Beteiligung motorisierter Fahrzeuge als Alleinunfall, bei Kollisionen mit Fußgängern oder Radfahrern. Viele Alleinunfälle werden nicht angezeigt, daher gibt es eine große Dunkelziffer. Das Schwergewicht der unfallbeteiligten Radfahrer liegt bei Kindern/Jugendlichen und bei Senioren. Der Anteil der Radfahrer als Hauptverursacher liegt bei ca. 47%. Hauptunfallstellen sind Kreuzungen und Einmündungen mit je über 28 %. Auf gesonderten Radwegen ist das Radfahren nur wenig sicherer als auf Straßen ohne Radwege; hinsichtlich der Unfallschwere ist das Bild uneinheitlich. Das Unfallgeschehen an Knotenpunkten wird genauer beschrieben.
Bus or heavy vehicle passenger accidents are rare events, compared with car accidents, but sometimes leads to a large number of victims especially in rollover crash scenarios. Two accidents occurred in Portugal in 2007 and 2013 in which 28 people died and more than 50 are injured, shown the importance of the investigation of such accidents. For the investigation of these accidents multidisciplinary teams are constituted with engineers and police officers. All the factors involved are taken into consideration including road design, traffic signs, maintenance and hardware, human factors, and vehicle factors. In this work a methodology to an accurate collection of the data is proposed. From the information collected the accident is reconstructed using the PC-CrashTM software. From this all the contribution factors are determined and recommendations to mitigate these crashes are listed. These two accidents are rollover accidents and the analysis of the injuries and its correlation with the use of retention systems is very important. From the medical data and with the dynamics of the accident determined simulations of the occupants with biomechanical models are carried out in order to evaluate the effect of the retention systems in the injuries. This analysis is based on injury criteria (such as Abbreviated Injury Score (AIS) or Injury Severity Scale (ISS)). With this it is possible to determine if the seat belt was worn or not.
Since its creation in 2011 the Pre-Crash-Matrix (PCM) offers the possibility to observe the pre-crash phase until five seconds before crash for a wide range of accidents. Currently the PCM contains more than 8.000 reconstructed accidents out of the GIDAS (German In-Depth Accident Study) database and is enlarged continuously by more than 1.000 cases per year. Hence, a detailed investigation of active safety systems in real accident situations has been made feasible. The PCM contains all relevant data in database format to simulate the pre-crash phase until the first collision of the accident for a maximum of two participants. This includes the definition of the participants and their characteristics, the dynamic behavior of the participants as time-dependent course for five seconds before crash as well as the geometry of the traffic infrastructure. The digital sketch of the accident and information from GIDAS as well as from supplementary databases represent the main input for the simulation of the pre-crash phase of an accident with the VUFO simulation model VAST (Vufo Accident Simulation Tool). This simulation in turn embodies the foundation of the PCM. The PCM underlies continual improvements and enhancements in consultation with its users. In addition to collisions of cars with other cars, pedestrians, bicycles and motorcycles the PCM now also covers car to object and car to truck collisions. The paper illustrates car to truck collisions as a showcase and explains perspectives for further developments. In 2016 a more detailed definition of the contour of the vehicle was added. Furthermore, the geometrical surroundings of the accident site will be provided in a new structure with a higher level of detail. Thus, a precise classification of road marks and objects is possible to further improve the support of developing and evaluating ADAS. This paper gives an overview about the latest developments of the PCM with its innovations and provides an outlook to upcoming enhancements. Besides potential areas of application for the development of ADAS are shown.
This work describes the results of the experimental activity, illustrating the driving behavior observed in different conditions, relating them to the different methods of ADAS intervention and comparing the driver behavior without ADAS. In the present study, driver behavior was studied in road accidents involving elderly pedestrians, with different ADAS HMIs, as a base to develop a driver model in near missing pedestrian accidents. A literature research was conducted with the aim of finding out the main influencing factors, including environment, boundary conditions, configuration of impact, pedestrian and driver information, when pedestrian fatalities occur and an analysis of frequent road accidents was conducted to get more detailed information about the driver- behavior. In order to obtain more detailed information about pedestrian accidents, real road accidents were reconstructed with multibody simulations on PC-Crash and, by the comparison between literature findings and reconstructions, a generic accident scenario was defined. The generic accident scenario was implemented on the full scale dynamic driving simulator in use at the Laboratory for Safety and Traffic Accident Analysis (LaSIS, University of Florence, Italy) in order to analyse the driving behaviors of volunteers, also considering the influence of ADAS devices. Forty-five young volunteers were enrolled for this study, resulting in forty valid tests on different testing scenarios. Two different scenarios consisted in driving with or without ADAS in the vehicle. Different kinds of ADAS, acoustic and optical, with different time of intervention were tested in order to study the different reactions of the driver. The tests showed some interesting differences between driver's behavior when approaching the critical situation. Drivers with ADAS reacted earlier, but more slowly, depending also on the type of alarm, and often with double reaction when braking. In fact, the results of the activity showed that with ADAS intervention the time to collision (TTC) increases, but the reaction time and braking modality change: a) there is a sort of "latency" time between the accelerator pedal release and the brake pressure; b) the brake pressure is initially less intense. So the driver only partially takes advance from the TTC increase. These differences were valued not only qualitatively, but quantitatively as well. This work revealed to be useful to improve the knowledge of drivers" behavior, in order to realize a driver model that can be implemented to help attaining and assessing higher levels of automation through new technology.
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
Causation of traffic accidents with children from the perspective of all involved participants
(2017)
In the year 2014 about 2,800 children between zero and 14 years got injured due to traffic accidents in Austria. More than 50% were taking part in traffic as active road users like cyclists or pedestrians. Within this study 46 real world traffic accidents between vehicles and children as pedestrians were analysed. In 39 cases, car drivers hit the crossing children. In the other cases, the collision opponents were busses, trucks or motorcycles. Most of the children got hit while crossing a road at urban sites. By analysing the traffic accidents from the perspectives of all involved participants, vehicle drivers and injured children, it is possible to identify factors for each participant, which led to the accident and factors that contributed the accident. The main task is to find patterns in the behaviour of crash victims (children and driver) before the collision. One important fact is that in more than 50% of the analysed cases sight obstructions were an important contributing factor for both, the driver and the child. From drivers view situations in which the child moved unexpected into the driven road lane were often found. For the injured child, factors like: no attention to the road traffic or no sufficient traffic observation were found to be relevant. Further it- possible to sensitise children and adults to possible source of critical traffic situations according to the findings of this study.
For more than a decade, ADAC accident researchers have analysed road accidents with severe injuries, recording some 20,000 accidents. An important task in accident research is to determine the causative factors of road accidents. Apart from vehicle engineering and human factors, accident research also focuses on infrastructural and environmental aspects. To find out what accident scenarios are the most common in ADAC accident research and what driver assistance systems can prevent them, our first task was to conduct a detailed accident analysis. Using CarMaker, we performed a realistic simulation of accident scenarios, including crashes, with varying parameters. To begin with, we made an initial selection of driver assistance systems in order to determine those with the greatest accident prevention potential. One important finding of this study is that the safety potential of the individual driver assistance systems can actually be examined. It also turned out that active safety offers even much more potential for development and innovation than passive safety. At the same time, testing becomes more demanding, too, as new systems keep entering the market, many of them differing in functional details. ADAC will continue to test all driver assistance systems as realistically as possible so as to be able to provide advice to car buyers. Therefore, it will be essential to develop and improve test conditions and criteria.
The proportion of older road users is increasing because of demographic change (in the group 65+ from current 18% to about 24% by 2030). The mobility needs of people 65+ often differ from those of younger people. Seniors (65+) are already more involved in fatal accidents than younger road users. According to the age development, the senior share of road deaths in the EU of today is increasing nearly one-fifth to one-third. From the in-depth analysis of accidents generic simulation models were developed. Attention has been paid both to psycho-physical characteristics as well as on the social and physical environment and their specifics in conjunction with seniors. By simulating the defined scenarios and varying the defined relevant parameters, accident influencing factors were examined as a basis for avoidance. In addition, the parameters were varied to show the influence from the vehicle, the pedestrian and the infrastructure to avoid the accident or to characterize the conditions for which the accident is inevitable.
Twenty-eight percent of traffic accidents in Japan are rear-end collisions, and of these, 13% are multiple collisions (three or more vehicles and/or roadside objects). A post-crash braking system enables the driver to stop the vehicle in a short distance after a rear-end collision to prevent secondary collisions. In this study, the effectiveness of a post-crash braking system was examined using a drive recorder database. In 64% of rear-end collisions, the driver's braking was interrupted after the collision. The stopping distance was estimated with time data from the drive recorder. We predict that the brake assist would be effective in preventing secondary collisions in 21% of cases.
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
In this study, the mean profile depth (MPD) that expresses roughness of road pavements was calculated using the road survey equipment vehicle and the calculated MPD was compared with the real number of traffic accidents. The analysis method used in this study was to classify the appropriate clustering in relation to traffic accidents using the K-means clustering and to compare this with the presence of traffic accidents via the MPDs to derive the result. K-means clustering was used in the analysis method and four clusters were found using the clustering analysis results. The center of each cluster was 0.627, 0.850, 1.118, and 1.237, respectively. The result of this study is expected to be utilized as foundational research in the traffic safety area.
Powered Two Wheeler (Motorcycle) crashes are overrepresented in EU, England, and United States casualty statistics for both fatal and serious injuries. While regional geographic differences are evident for motorcycle size, type, and engine displacement, the casualty statistics consistently indicate significantly higher injury rates for all motorcycle riders when compared to car occupants. Accident analysis and reconstruction of these motorcycle crashes is a necessary process to gain further understanding of potential injury mitigation strategies. This paper focuses on the analysis of the rider post impact trajectory in the immediate moments following a crash. The rider and motorcycle, while loosely coupled by seating position leading up to a crash, quickly decouple as the crash forces develop. As a result, the rider moves relative to the motorcycle and relative to the collision partner. This movement, or trajectory, is primarily influenced by the type and configuration of the impact, the type and configuration of the motorcycle and collision partner, and the speeds involved. Understanding the rider's post impact trajectory will assist in the development of injury mitigation strategies. Both the free flight trajectory of the rider and the rider's trajectory as influenced by interaction with the motorcycle and collision partner are examined. Rider trajectories in full scale crash testing and real world motorcycle crashes are both studied and presented. The resulting physical evidence that can be observed by an accident analyst is discussed. The application of projectile motion physics is analyzed and the necessary input parameters, such as initial launch angle, are studied. This study will assist in understanding the post-impact dynamics of a motorcyclist, and will provide useful information to analysts evaluating real world crashes.
Cyclists are more likely to be injured in fatal crashes than motorised vehicles. To gain detailed and precise behavioural data of road users, i.e. trajectories, a measuring campaign was conducted. Therefore, a black-spot for accidents with cyclists in Berlin, Germany was selected. The traffic has been detected by a fully automated traffic video analysis system continuously for twelve hours. The video surveillance system is capable of automatically extracting trajectories, classifying road user types and precise determining and positioning of conflicts and accidents. Additionally, pre-conflict and pre-accident situations could be analysed to provide further in-depth understanding of accident causation. The evaluation of the measuring campaign comprised the investigation of traffic parameters, e.g. traffic flow, as well as traffic-safety related parameters based on Surrogate Safety Measures (SSM). Furthermore, the spatial and temporal distributions of conflicts involving cyclists were determined. As a result, three possible conflict clusters could be identified, of which one cluster could be confirmed by detailed video analysis, showing conflicts caused by right turning vehicles.
Car occupants have a high level of mortality in road accidents, since passenger cars are the prevalent mode of transport. In 2013, car occupant fatalities accounted for 45% of all road accident fatalities in the EU. The objective of this research is the analysis of basic road safety parameters related to car occupants in the European countries over a period of 10 years (2004-2013), through the exploitation of the EU CARE database with disaggregate data on road accidents. Data from the EU Injury Database for the period 2005 - 2008 are used to identify injury patterns, and additional insight into accident causation for car occupants is offered through the use of in-depth accident data from the EC SafetyNet project Accident Causation System (SNACS). The results of the analysis allow for a better understanding of the car occupants' safety situation in Europe, thus providing useful support to decision makers working for the improvement of road safety level in Europe.
Injury probability functions for pedestrians and bicyclists based on real-world accident data
(2017)
The paper is focusing on the modelling of injury severity probabilities, often called as Injury Risk Functions (IRF). These are mathematical functions describing the probability for a defined population and for possible explanatory factors (variables) to sustain a certain injury severity. Injury risk functions are becoming more and more important as basis for the assessment of automotive safety systems. They contribute to the understanding of injury mechanisms, (prospective) evaluation of safety systems and definition of protection criteria or are used within regulation and/or consumer ratings. In all cases, knowledge about the correlation between mechanical behavior and injury severity is needed. IRFs are often based on biomechanical data. This paper is focusing on the derivation of injury probability models from real world accident data of the GIDAS database (German In-depth Accident Study). In contrast to most academic terms there is no explicit term definition or definition of creation processes existing for injury probability models based on empirical data. Different approaches are existing for such kind of models in the field of accident research. There is a need for harmonization in terms of the used methods and data as well as the handling with the existing challenges. These are preparation of the dataset, model assumptions, censored/unknown data, evaluation of model accuracy, definition of dependent and independent variable, and others. In the presented study, several empirical, statistical and phenomenological approaches were analyzed regarding their advantages and disadvantages and also their applicability. Furthermore, the identification of appropriate prediction parameters for the injury severity of pedestrians has been considered. Due to its main effect on injuries of pedestrians and bicyclists, the importance of the secondary impact has also been analyzed. Finally, the model accuracy, evaluated by several criteria, is the rating factor that gives the quality and reliability for application of the resulting models. After the investigation and evaluation of statistical approaches one method was chosen and appropriate prediction variables were examined. Finally, all findings were summarized and injury risk functions for pedestrians in real world accidents were created. Additionally, the paper gives instructions for the interpretation and usage of such functions. The presented results include IRFs for several injury severity levels and age groups. The presented models are based on a high amount of real world accidents and describe very well the injury severity probability of pedestrians and bicyclists in frontal collisions with current vehicles. The functions can serve as basis for the evaluation of effectiveness of systems like Pedestrian-AEB or Bicycle-AEB.
When assessing the consequences of accidents normally the injury severity and the damage costs are considered. The injury severity is either expressed within the police categories (slight injury, severe injury or fatal injury) or the AIS code that rates the fatality risk of a given injury. Both injury metrics are assessing the consequences of the accident directly after the accident. However, not all consequences of accidents are visible directly after the accident and the duration of the consequences are different. Besides a physiological reduction of functionality social and psychological implications such as reduced mobility options, problems to continue the original job etc. are happening. In order to assess long term consequences of accidents the MHH Accident Research Unit established a brief questionnaire that is distributed to accident involved people of the Hannover subset of the GIDAS data set approx. one year after the accident beginning with the accident year 2013. The basic idea of using a brief questionnaire (in fact only one page) is to obtain a relatively large return rate because the questionnaire appears to be simple and quickly answered. This appears to be important because it is believed that the majority of accident involved people will not report long term consequences. In order to allow a more detailed survey amongst those responders that are reporting long term consequences they are asked for a written consent for the additional questionnaire that will be distributed at a time that is not yet defined. Long term consequences are reported for all addressed areas, medical, physiological, psychological and sociological by people without injuries, with minor injuries and with severe injuries.
[Introduction:] A large number of road users involved in road traffic crashes recover from their injuries, but some of them never recover fully and suffer from some kind of permanent disability. In addition to loss of life or reduced quality of life, road accidents carry many and diverse consequences to the survivors such as legal implications, economic burden, job absences, need of care from a third person, home and vehicle adaptations as well as psychological consequences. Within an EU funded project MOVE/C4/SUB/2011-294/SI2.628846 (REHABIL AID) these consequences were analyzed more detailed.
The objectives of this paper are the analysis of the accident risk of drivers brain pathologies (Mild Cognitive Impairment, Alzheimer- disease, and Parkinson- disease), and the investigation of the impact of driver distraction on the accident risk of patients with brain pathologies, through a driving simulator experiment. The three groups of patients are compared to a healthy group of similar demographics, with no brain pathology. In particular, 125 drivers of more than 55 years old (34 "controls"" and 91 "patients") went through a large driving simulator experimental process, in which incidents were scheduled to occur. They drove in rural and urban areas, in low and high traffic volumes and in three distraction conditions (undistracted driving, conversation with a passenger and conversation through a mobile phone). The statistical analyses indicated several interesting findings; brain pathologies affect significantly accident risk and distraction affects more the groups of patients than the control one.
Whiplash injuries are characterized by the high variability of its symptoms and by the subjectivity of its diagnosis, which sometimes leads to frauds perpetrated by victims of rear-end impacts. It is estimated that whiplash injuries cost annually about 10.000 million Euros in Europe. Therefore, the aim of this study was to investigate the influence of the dynamics of the accident in which the victim was involved in the probability of development of whiplash associated injuries. In the presented methodology, first an accident reconstruction is performed where the dynamics of the accident is determined. This is carried out using the software PC-Crash, police and insurance companies' data. Then biomechanical injuries criteria related with whiplash injuries are evaluated. For the evaluation of the probability of having whiplash injuries, the Neck Injury Criterion (NIC) of the victim and the mean acceleration of the vehicle were evaluated. Then, with medical reports, the results of the accident reconstruction are correlated with the reported injuries. Some examples are presented. The results obtained indicate that the study of the dynamics of the road accidents in which the victims were involved could be used as an auxiliary of the prognosis of whiplash injuries and is important for a precise diagnosis of this type of injuries.
In most of developed countries, the progress made in passive safety during the last three decades allowed to drastically reduce the number of killed and severely injured especially for occupants of passenger cars. This reduction is mainly observed for frontal impacts for which the AIS3+ injuries has been reduced about 52% for drivers and 38% for front passengers. The stiffening of the cars' structure coupled with the generalization of airbags and the improvement of the seatbelt restraint (load limiter, pretension, etc.) allowed to protect vital body regions such as head, neck and thorax. However, the abdomen did not take advantage with so much success of this progress. The objective of this study is to draw up an inventory on the abdominal injuries of the belted car occupants involved in frontal impact, to present adapted counter-measures and to assess their potential effectiveness. In the first part the stakes corresponding to the abdominal injuries will be defined according to types of impact, seat location, occupants' age and type of injured organs. Then, we shall focus on the abdominal injury risk curves for adults involved in frontal impact and on the comparisons of the average risks according to the seat location. In the second part we will list counter-measures and we shall calculate their effectiveness. The method of case control will be used in order to estimate odds ratio, comparing two samples, given by occupants having or not having the studied safety system. For this study, two type of data sources are used: national road injured accident census and retrospective in-depth accident data collection. Abdominal injuries are mainly observed in frontal impact (52%). Fatal or severe abdominal occupant- injuries are observed at least in 27% of cases, ranking this body region as the most injured just after the thorax (51%). In spite of a twice lower occupation rate in the back seats compared to the front seats, the number of persons sustaining abdominal injuries at the rear place is higher than in the front place. In recent cars, the risk of having a serious or fatal abdominal injury in a frontal impact is 1.6% for the driver, 3.6% for the front passenger and 6.3% for the rear occupants. The most frequently hurt organs are the small intestine (17%), the spleen (16%) and the liver (13%). The most common countermeasures have a good efficiency in the reduction of the abdominal injuries for the adults: the stiffness of the structure of the seats allows decreasing the abdominal injury risk from 54% (driver) to 60% (front occupant), the seatbelt pretensioners decrease also this risk from 90% (driver) to 83% (front passenger).
Still correlated with high mortality rates in traffic accidents traumatic aortic ruptures were frequently detected in unprotected car occupants in the early years. This biomechanical analysis investigates the different kinds of injury mechanisms leading to traumatic aortic injuries in todays traffic accidents and how the way of traffic participation affects the frequency of those injuries over the years. Based on GIDAS reported traffic accidents from 1973 to 2014 are analyzed. Results show that traumatic aortic injuries are mainly observed in high-speed accidents with high body deceleration and direct load force to the chest. Mostly chest compression is responsible for the load direction to the cardiac vessels. The main observed load vector is from caudal-ventral and from ventral solely, but also force impact from left and right side and in roll-over events with chest compression lead to traumatic aortic injuries. Classically, the injury appeares at the junction between the well-fixed aortic arch and the pars decendens following a kind of a scoop mechanism, a few cases with a hyperflexion mechanism are also described. In our analysis the deceleration effect alone never led to an aortic rupture. Comparing the past 40 years aortic injuries shift from unprotected car occupants to today's unprotected vulnerable road users like pedestrians, cyclists and motorcyclists. Still the accident characteristics are linked with chest compression force under high speed impact, no seatbelt and direct body impact.
To elucidate the risk of pedestrians, bicycle and motorbike users, data of two accident research units from 1999 to 2014 were analysed in regard to demographic data, collision details, preclinical and clinical data using SPSS. 14.295 injured vulnerable road users were included. 92 out of 3610 pedestrians ("P", 2.5%), 90 out of 8307 bicyclists ("B", 1.1%) and 115 out of 4094 motorcycle users ("M", 2.8%) were diagnosed with spinal fractures. Thoracic fractures were most frequent ahead of lumbar and cervical fractures. Car collisions were most frequent mechanism (68, 62 and 36%). MAIS was 3.8, 2.8 and 3.2 for P, B and A with ISS 32, 16 and 23. AIS-head was 2.2, 1.3 and 1.5). Vulnerable road users are at significant risk for spine fractures. These are often associated with severe additional injuries, e.g. the head and a very high overall trauma severity (polytrauma).
While cyclists and pedestrians are known to be at significant risk for severe injuries when exposed to road traffic accidents (RTAs) involving trucks, little is known about RTA injury risk for truck drivers. The objective of this study is to analyze the injury severity in truck drivers following RTAs. Between 1999 and 2008 the Hannover Medical School Accident Research Unit prospectively documented 43,000 RTAs involving 582 trucks. Injury severity including the abbreviated injury scale (AIS) and the maximum abbreviated injury scale (MAIS) were analyzed. Technical parameters (e.g. delta-v, direction of impact), the location of accident, and its dependency on the road type were also taken into consideration. The results show that the safety of truck drivers is assured by their vehicles, the consequence being that the risk of becoming injured is likely to be low. However, the legs especially are at high risk for severe injuries during RTAs. This probability increases in the instance of a collision with another truck. Nevertheless, in RTAs involving trucks and regular passenger vehicles, the other party is in higher risk of injury.
A study on knowledge and practices of first aid and CPR among police officers in Colombo and Gampaha
(2017)
Around 85% of deaths in developing countries have been found to be due to road traffic accidents (RTAs), which cost the countries around 1-2% of their gross national product (GNP). In Sri Lanka there were 2,436 deaths reported from 36,045 RTAs in 2014. This study aimed at assessing first aid and cardiopulmonary resuscitation (CPR) knowledge among police officers and identifying its relationship to their first aid and CPR practices. A study was done on 493 police officers from Colombo and Gampaha who were selected using convenience sampling through a self-administered questionnaire. The results showed that the police officers had unsatisfactory knowledge and practices of CPR and interventions for bleeding and fractures. These should therefore be focused in their further training.
In this study, we compared the injury severity of occupants according to the seating position and the crashing direction in motor vehicle accidents. In the driver's point of view, it was separated the seating position as "Near-side" and "Far-side". The study subjects were targeted by people who visited 4 regional emergency centers following motor vehicle accidents. Real-world investigation was performed by direct and indirect methods after patient- consent. The information of the damaged vehicle was informed by Collision Deformation Classification (CDC) code and the information of the injury of patients was informed by using the Abbreviated Injury Score (AIS) and Injury Severity Score (ISS). When the column 3 in CDC code was P, damaged at the middle part of lateral side, the average point of AIS 3 was 1.91-±1.72 in near-side and 1.02-±1.31 in far-side (p<0.01). The average point of maximum AIS (MAIS) was 2.78-±1.39 in near-side and 2.02-±1.11 in far-side (p<0.01). The average point of ISS was 15.74-±14.71 in near-side and 8.11-±8.39 in far-side (p<0.01). Also, when the column 3 in CDC code was D, damaged at the whole part of lateral side, it was significant that the average point of AIS 3 and MAIS in near-side was bigger than in far-side (p=0.02).
In-depth accident investigation offers many advantages for the analysis and comprehension of crash mechanisms. IFSTTAR makes such investigations since 1992 without interruption. The corresponding database contains more than 1200 accident case studies. Currently, in-depth accident investigation is one of the best ways to determine the speed or cars involved in accidents. This paper first presents the methods used for accident investigation and for accident kinematic reconstruction. Then, in order to illustrate the interest and possible applications of such accident data, it shows some results from a recent study based on the IFSTTAR in-depth accident study programme (IDAS) and dealing with the link between travelling speed and accident risk.
For the avoidance of traffic accidents by means of advanced driver assistance systems the knowledge of failures and deficiencies a few seconds before the crash is of increasing importance. This information e.g. is collected in the German accident survey GIDAS by an interview derived from the ACAS methodology. However to display the whole range of accident causation factors additional information is needed on enduring factors of the system components "human", "infrastructure" and "machine". On the strategic level these accident moderating factors include long term influences such as medical preconditions or a general higher risk taking behavior as well as influences on the immediate conflict level such as an aggressive response to a perceived previous traffic conflict. This study was conducted to examine the feasibility of collecting such causation information in the scope of an in-depth accident investigation like GIDAS. Due to the comprehensive amount of information necessary to estimate the moderating factors the collection of the information is distributed to different methods. 5 cases of real world crashes have been investigated where information was collected on-scene and retrospective by interviews. The identified moderating factors of the accidents and the method for collecting the information are displayed.
Motorcycle crashes in Austria: Analysis of causes and contributing factors based on in-depth data
(2017)
From CEDATU, the in-depth accident database run by the Vehicle Safety Institute at Graz University of Technology, a representative sample of 101 crashes involving at least one motorcycle was selected. The analysis focused on causes for crashes as well as on contributing factors, but also included parameters of road, riders and vehicles. Own riding speed and "unexpectable action by another road user" were the most frequent causes for accidents. Inappropriate safety distance or delayed reaction were frequent, both as causation factors and as contributing factors. Infrastructure issues never cause an accident, but they are very frequent as contributing factors; road geometry and road guidance are by far most frequent among these. This paper also discusses accidents by type and other parameters (e.g. injury severity by body region, collision speed, age and others), and compares accident causes to previous studies as well as the police reported accident statistics.