Filtern
Erscheinungsjahr
Dokumenttyp
Volltext vorhanden
- nein (38) (entfernen)
Schlagworte
- Anfahrversuch (38) (entfernen)
Institut
- Abteilung Fahrzeugtechnik (38) (entfernen)
The off-set assessment procedure potentially contributes to the FIMCAR objectives to maintain the compartment strength and to assess load spreading in frontal collisions. Furthermore it provides the opportunity to assess the restraint system performance with different pulses if combined with a full-width assessment procedure in the frontal assessment approach. Originally it was expected that the PDB assessment procedure would be selected for the FIMCAR assessment approach. However, it was not possible to deliver a compatibility metric in time so that the current off-set procedure (ODB as used in UNECE R94) with some minor modifications was proposed for the FIMCAR Assessment Approach. Nevertheless the potential to assess load spreading, which appears not to be possible with any other assessed frontal impact assessment procedure was considered to be still high. Therefore the development work for the PDB assessment procedure did not stop with the decision not to select the PDB procedure. As a result of the decisions to use the current ODB and to further develop the PDB procedure, both are covered within this deliverable. The deliverable describes the off-set test procedure that will be recommended by FIMCAR consortium, this corresponds to the ODB test as it is specified in UN-ECE Regulation 94 (R94), i.e. EEVC deformable element with 40% overlap at a test speed of 56 km/h. In addition to the current R94 requirements, FIMCAR will recommend to introduce some structural requirements which will guarantee sufficiently strong occupant compartments by enforcing the stability of the forward occupant cell. With respect to the PDB assessment procedure a new metric, Digital Derivative in Y direction - DDY, was developed, described, analysed, and compared with other metrics. The DDY metric analyses the deformation gradients laterally across the PDB face. The more even the deformation, the lower the DDY values and the better the metric- result. In order analyse the different metrics, analysis of the existing PDB test results and the results of the performed simulation studies was performed. In addition, an assessment of artificial deformation profiles with the metrics took place. This analysis shows that there are still issues with the DDY metric but it appears that it is possible to solve them with future optimisations. For example the current metric assesses only the area within 60% of the half vehicle width. For vehicles that have the longitudinals further outboard, the metric is not effective. In addition to the metric development, practical issues of the PDB tests such as the definition of a scan procedure for the analysis of the deformation pattern including the validation of the scanning procedure by the analysis of 3 different scans at different locations of the same barrier were addressed. Furthermore the repeatability and reproducibility of the PDB was analysed. The barrier deformation readings seem to be sensitive with respect to the impact accuracy. In total, the deliverable is meant to define the FIMCAR off-set assessment procedure and to be a starting point for further development of the PDB assessment procedure.
Sowohl mit dem 3. Road Safety Action Programme der Europäischen Kommission als auch mit dem deutschen Verkehrssicherheitsprogramm werden die verkehrspolitischen Zielsetzungen zur Erhöhung der Verkehrssicherheit in Europa und Deutschland festgelegt. Hierbei muss die passive Fahrzeugsicherheit auch weiterhin eine bedeutende Rolle übernehmen. Es ist jedoch auch festzustellen, dass durch den zunehmenden Einsatz von Elektronik im Fahrzeug die klassischen Bereiche der aktiven und passiven Fahrzeugsicherheit mehr und mehr ineinander greifen. Der Fortschritt in der Elektronik ermöglicht eine Integration der Systeme der aktiven und passiven Sicherheit. Dadurch lässt sich die Fahrzeugsicherheit weiter steigern. Durch die Vernetzung der Systeme lassen sich sogar Kosten einsparen. Der europäische Regierungsausschuss EEVC (European Enhanced Vehicle-safety Committee), die Verbraucherschutzorganisation Euro NCAP (European New Car Assessment Programme) und die Europäische Kommission mit der eSafety Initiative haben diesen Trend erkannt und entsprechende Aktivitäten eingeleitet.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
Wegen der wachsenden Verbreitung von Fahrradanhängern zum Kindertransport und der möglichen Unfallgefährdung ist im vorliegenden Forschungsprojekt deren passive Sicherheit untersucht worden. Zudem wurde der Frage nachgegangen, ob der Transport von Kindern im Fahrradanhänger sicherer ist als mit dem Fahrrad mit Kindersitzen. In Absprache mit Herstellern und Vertreibern wurden verschiedene Untersuchungen durchgeführt. Es handelte sich um Anprallversuche (Anfahrversuche), Rollwagenversuche (Schlittenversuche) sowie Kopffreiheitsprüfungen und Fallversuche. Bei den Versuchen waren die Prüfobjekte mit einem oder zwei Dummies besetzt, die mit Messdatenaufnehmern ausgestattet waren. Verschiedene Messdaten, zum Beispiel Kopf- und Brustbeschleunigung, wurden erfasst und ausgewertet. Zusätzlich wurde das Kopfschutzkriterium (HPC) berechnet und bewertet. Entstandene Schäden an den Prüfobjekten wurden aufgenommen und durch Fotos dokumentiert. Die Versuchsabläufe selbst wurden mit Hochgeschwindigkeitskameras aus verschiedenen Positionen aufgezeichnet. Beim Anfahrversuch mit einem Pkw gegen ein Gespann aus Fahrrad und Anhänger waren direkte Anstöße der Anhängerinsassen an die Pkw-Front zu erkennen. Die Beschleunigungswerte waren dabei relativ hoch. Anstöße gegen Anhängerinnenteile waren bei fast allen Versuchen zu beobachten. Teilweise wurden Radaufhängungen und Radnaben beschädigt. Durch die Rollwagenversuche wurden konstruktive Schwächen bei den Sitzen und Rückhaltesystemen festgestellt. Nähte, Befestigungen und Verstellösen wurden zerstört. Es stellte sich heraus, dass die Qualität des Gurtsystems, die Steifigkeit des Anhängeraufbaus, die Sitzposition der Kinder und die vorhandene Kopffreiheit ausschlaggebend für das Verletzungsrisiko der Insassen sind. Bei den Versuchen mit Fahrradsitzen ergaben sich hohe Beschleunigungswerte durch den direkten Kontakt des Radfahrers mit der Fahrzeugfront und/oder der Fahrbahn. Das Gewicht des Radfahrers, des Fahrrades und auch Fahrradteile bergen ein erhöhtes Verletzungsrisiko für das Kind. Zusätzlich besteht die Gefahr überfahren zu werden, wenn das Kind nach dem Sturz des Fahrrades ungeschützt auf der Fahrbahn liegt. Ein direkter Vergleich der beiden Transportmöglichkeiten war aufgrund der geringen Daten der Versuche mit Fahrradkindersitzen nur bedingt möglich. Tendenziell ist der Transport der Kinder im Fahrradanhänger als weniger gefährlich zu bewerten. Es werden die Vor- und Nachteile dargestellt. Zur Bewertung der Sicherheit von Fahrradanhängern wurden die folgenden Prüfmethoden erarbeitet: - Pendelschlagprüfung für die gesamte Chassisstruktur; - Kopffreiheitsprüfung; - Belastungsprüfung der Aufbaustruktur; - Festigkeitsprüfung der Gurtsysteme. Die Prüfungen sind so aufgebaut, dass sie mit einfachen Mitteln durchzuführen sind. Es sollte somit jedem Anhängerhersteller möglich sein, die passive Sicherheit seiner Produkte umfassend zu untersuchen. Die Prüfverfahren für die Sicherheitsbewertung sollen in eine DIN-Norm und in das Merkblatt für Fahrradanhänger einfließen. Der Original-Forschungsbericht enthält einen umfangreichen Fotoband zu den Einzelheiten der Versuche und Versuchsaufbauten sowie zu den Beschädigungen der Prüfobjekte und kann bei der BASt eingesehen werden.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
To improve vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility aims to improve both the self and partner protection properties of vehicles. Although compatibility has received worldwide attention for many years, no final assessment approach has been defined. Within the Frontal Impact and Compatibility Assessment Research (FIMCAR) project, different frontal impact test procedures (offset deformable barrier [ODB] test as currently used for Economic Commission for Europe [ECE] R94, progressive deformable barrier test as proposed by France for a new ECE regulation, moveable deformable barrier test as discussed worldwide, full-width rigid barrier test as used in Federal Motor Vehicle Safety Standard [FMVSS] 208, and full-width deformable barrier test) were analyzed regarding their potential for future frontal impact legislation. The research activities focused on car-to-car frontal impact accidents based on accident investigations involving newer cars. Test procedures were developed with both a crash test program and numerical simulations. The proposal from FIMCAR is to use a full-width test procedure with a deformable element and compatibility metrics in combination with the current offset test as a frontal impact assessment approach that also addresses compatibility. By adding a full-width test to the current ODB test it is possible to better address the issues of structural misalignment and injuries resulting from high acceleration accidents as observed in the current fleet. The estimated benefit ranges from a 5 to 12 percent reduction of fatalities and serious injuries resulting from frontal impact accidents. By using a deformable element in the full-width test, the test conditions are more representative of real-world situations with respect to acceleration pulse, restraint system triggering time, and deformation pattern of the front structure. The test results are therefore expected to better represent real-world performance of the tested car. Furthermore, the assessment of the structural alignment is more robust than in the rigid wall test.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
Since integrated safety systems combine active and passive safety elements in one safety system, it is necessary to define new procedures to evaluate vehicle safety from the overall system point of view. The main goal of the ASSESS project is to develop harmonized and standardized assessment procedures for collision mitigation and avoidance systems. Methods and Data Sources: In ASSESS, procedures are developed for: driver behaviour evaluation, pre-crash system performance evaluation, crash performance evaluation, socio-economic assessment. This paper will concentrate on the activities related to the crash evaluation. The objective is to perform simulations, sled tests and crash tests in order tounderstand the influence of the activation of the pre-crash systems on the occupants" injuries during the crash phase. When a traffic accident is unavoidable, pre-crash systems work on various safety devices in order to improve the vehicle occupants" protection. Braking assistance and adaptive restraint systems are the main pre-crash systems whose effect on the occupants" protection will be described in this paper. Results: The results will be a description of the effect of the activation of the pre-crash systems on the crash phase. Additionally, a set of recommendations for future methodology developments will be delivered. Furthermore, a first approach to the study of the effect of the pre-crash systems activation on the occupants" protection when the impact is unavoidable will be presented. This effect will be quantified using the biomechanical values obtained from the simulation and testing activities and their related injury risks. Simulation and testing activities will consider the following scenarios: - No activation of any pre-crash system, - Activation of one or a combination of several pre-crash systems. In this way, differences in the results obtained from different scenarios will show the effect of each pre-crash system separately during the crash phase. Discussion and Limitations: The set of activities developed in this research project is limited by the fact that with the given resources only a limited number of vehicle models could be investigated. In addition, there are also limitations related to the injury risk curves and the passive safety tools currently on the market. Conclusion and Relevance to session submitted: The paper will present a complete analysis of the effect of pre-crash systems during the crash phase when the impact is unavoidable. Details, limitations and first application experience based on a few examples will be discussed. Currently, there is not any regulation, assessment program, or other similar official procedure able to assess pre-crash systems during the crash phase. This project comprises phases of traffic accidents which have been historically analysed separately, and aims to evaluate them taking into account their interrelationship. ASSESS is one of the first European projects which deals in depth with the concept of integrated safety, defining methodologies to analyse vehicle safety from a global point of view.
The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx. However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My. The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was observed. It was also observed that the primary neck response in these tests was flexion, not extension. This correlates well with recent findings from Japan and the United States showing a correlation between neck flexion and injury in accident replication simulations and postmortem human subjects (PMHS) studies, respectively. The present certification tests may not adequately control front cervical spine bumper characteristics, which are important for neck flexion response. The certification sled test also does not include the pelvis and so cannot be used to control pelvis response and does not substantially load the lumbar bumpers and so does not control these parts of the dummy. The stiffness of all spine bumpers and of the pelvis flesh should be much more tightly controlled. It is recommended that a method for certifying the front cervical bumpers should be developed. Recommendations are also made for tighter tolerance on the input parameters for the existing certification tests.