Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (409) (entfernen)
Sprache
- Englisch (409) (entfernen)
Schlagworte
- Conference (278)
- Konferenz (276)
- Unfall (157)
- Accident (156)
- Germany (155)
- Deutschland (153)
- Injury (110)
- Verletzung (110)
- Unfallrekonstruktion (80)
- Safety (74)
During a lifecycle a tyre undergoes degradations due to mechanical wear and chemical ageing which affect not only durability and safety but also tyre/road noise emission and rolling resistance. This paper presents a study with the purpose to study how much tyre/road noise and rolling resistance change when car tyres are worn down from the original 8 mm tread depth to 2 mm, and when chemical ageing of the tyre rubber is simulated by exposure to heat. Six car tyres of different types were selected for the study which were worn on a wear machine in steps of 2 mm tread depth. Before, between and after these wear sessions tyre/road noise and rolling resistance were measured on two drum facilities with different surface textures, including replicas of ISO surfaces. Additionally, coast-by and CPX measurements were made on outdoor ISO test tracks. The results show that the wear and age effect was low on ISO surfaces but dramatic (noise increased with wear) on the rough-textured surface and high but opposite on an extremely smooth surface.
Twenty-eight percent of traffic accidents in Japan are rear-end collisions, and of these, 13% are multiple collisions (three or more vehicles and/or roadside objects). A post-crash braking system enables the driver to stop the vehicle in a short distance after a rear-end collision to prevent secondary collisions. In this study, the effectiveness of a post-crash braking system was examined using a drive recorder database. In 64% of rear-end collisions, the driver's braking was interrupted after the collision. The stopping distance was estimated with time data from the drive recorder. We predict that the brake assist would be effective in preventing secondary collisions in 21% of cases.
Mechanical properties of tibial bone at compressive strain rates of 50-200 s-1 are obtained through Split Hopkinson pressure bar. Cylindrical specimens of 12-15 mm diameter and 2-5 mm thickness were used. The Young- moduli are calculated from linear portion of stress-strain curves. For both cortical and cancellous part of the bones, the Young- modulus was found to increase with the increasing strain rates. Also for both cancellous and cortical bones the Young- modulus increases consistently with increase in densities.
Research to inform policy is often challenged with how to genuinely use and implement research findings in decision-making and policy-planning. To begin with, the dialogue between researchers and decision-makers is essential to ensure profound understanding and legitimate interpretations of the results. Furthermore, the step to drawing practical conclusions and processing them into actions can only succeed if research findings are diffused to decision-making levels with influence on the matter, and mechanisms to knowledge transfer in the presence of a stable, favourable policy environment exist. Research investments into the topic of electromobility in Europe are substantial, and subtopics aiming to inform national policy-makers address a complex set of aspects from environmental and societal to technological and economic. This paper has a two-fold objective, the first of which is to present the results of scenarios to explore electromobility deployment in Finland, Germany and the European Union. The second is to discuss the challenges and solutions to bridge the gap from research findings towards decision-making and policy-planning, using the authors' electromobility scenario work as an example. The electromobility scenarios were built using the VECTOR21 model (Mock, 2010), and the rationale was to simulate vehicle sales and markets under different policy settings and calculate the most economical solution to fulfill regulation on COâ‚‚ emissions as set by the European Commission (2009). The model allows calculating the market diffusion of alternative powertrain technologies to the European market until 2030, taking into account different taxation schemes, incentives and other country-specific characteristics. The authors also present the cost-benefit-analysis of the modelling results to assess the different scenarios and to show variation between regions regarding profitability of alternative technological or political support and interventions. To proceed from research findings towards decision-making and policy-planning, the authors made observations relating to transfer of research knowledge and interpretation of their electromobility scenario results in national policy contexts. An evaluation of how the function of research to inform policy in this case succeeded is provided. In addition, the influence of expert opinions on the political decision-making process will be discussed through experiences from an expert questionnaire conducted to survey the importance of costs, time requirement, acceptance and other criteria of promotion measures of electromobility.
A change emerges in hospital landscape due to health political measures, which in consequence also influences the pre-clinical medical care of emergencies. The main focus of this study was to gather information about emergency medical care after traffic accidents on the basis of data of Bavarian emergency medical services. In Bavaria, in 2006 it was necessary to call an emergency doctor in the case of 14.261 traffic accidents. Predominantly the patients were provided by land-based life saving appliances, air rescue services were only applied in 19.1 % of the cases. 47.6 % of patients being involved in a traffic accident were transported into a primary health care hospital. A prehospital interval of more than 60 minutes was calculated in 20 % of emergency care. 96.2 % of the patients were transported to hospitals of tertiary or maximum supply by air rescue services. The life saving appliances" readiness for action is however restricted to daylight. A further limitation appeared for routine office hours in hospitals: Only 36.7 % of accidents occurred in this time frame. An increase of hospitalizations in clinics of maximum supply appeared from 2002 until 2006 while simultaneously the prehospital period was extended. To assure a sufficient medical care of seriously injured persons further on, a fulltime and area-wide expostulation of efficient facilities is necessary. For this purpose it is necessary to establish regional trauma networks as well as emergency medical service at night time. Beyond that, a cost efficient compensation of the structural, personnel and logistic expenses has to be assured.
The need for improved EU level accident information and data was identified in the EU White Paper on Transport Policy (2001)1 and detailed in the Road Safety Action Plan (2003)2. The plan specifies that the EC will develop a road safety observatory to coordinate data collection within an integrated framework.
Although the annual traffic accident statistics published by the national police is available in public, the detailed traffic accident data has not been released in Korea. Recently the Ministry of Land, Infrastructure and Transport recognized the importance of in-depth accident data to enhance road traffic safety and initiated a research project to establish a collection of the detailed accident data. The main objective of the project is a feasibility study to establish KIDAS (Korea In-Depth Accident Study). Within this project, three university hospitals which are located in mid-size cities have been selected to collect accident data. Annually, more than 500 cases of accidents have been collected from the in-patient's interviews and diagnosis. Unlike GIDAS (German In-Depth Accident Study), currently on-site investigation can"t be performed by the Korean police. The only available data is patient medical records, patient's description of accident circumstances and the damaged vehicle. Occasionally the police provide the accident investigation reports containing very brief information on accident causation and vehicle safety. In a first step, the concept of KIDAS is to adopt the format of iGLAD (Initiative for the Global Harmonization of Accident Data) for harmonization. Since the currently collected accident information is extremely limited compared with GIDAS, the other sources of data and calculations such as KNCAP vehicle data, pc-crash simulations, vehicle registration information, insurance company data are utilized to complete the iGLAD template. Results from KIDAS_iGLAD and the cases of assessment of active safety devices such as AEBS, ESC, and LDWS will be evaluated.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
Estimation of the benefits for the UK for potential options to modify UNECE Regulation No. 95
(2010)
The side impact problem in Europe remains substantial. UK data shows that between 22% and 26% of car occupant casualties are involved in a side impact, but this rises to between 29% and 38% for those who are fatally injured. This indicates the more injurious nature of side impacts compared with frontal impacts. The European Enhanced Vehicle safety Committee (EEVC) has performed work to address the side impact issue since 1979. As part of its continuing work, it has recently investigated potential options for regulatory changes to improve side impact protection in cars further. To support this work the UK undertook an analysis to estimate the benefit for potential options to modify UNECE Regulation 95. The analysis used the UK national STATS19 and detailed Co-operative Crash Injury Study (CCIS) accident databases. Of the potential options reviewed, it was found that the addition of a pole test offered the greatest benefit.
In line with the new definition introduced by the European Commission (EC), the number of seriously injured road casualties in Germany for 2014 is assessed in this study. The number of MAIS3+ casualties is estimated by two different methodological approaches. The first approach is based on data from the German Inâ€Depth Accident Study (GIDAS), which is closely related to the German Road Traffic Accident Statistics. The second approach is based on data from the German TraumaRegister DGU-® (TRâ€DGU), which includes many more hospitals but not all MAIS3+ injuries.
This paper will outline ETSC's contribution to the European Union's road safety policy 2011-2020. It will present some of the main recommendations from ETSC's Blueprint for the 4th Road Safety Action Programme and will introduce the response to the European Commission's Road Safety Policy Orientations 2011-2020 (published July 2010). The second framework document presented is the Transport White Paper (published March 2011). The paper will focus on new targets and the new vision set for Europe's Road Safety policy picking out some issues in particular such as traffic law enforcement and the protection of vulnerable road users. It will argue that by reinforcing the current Road Safety Policy Orientations, the EU will be better placed to reach its new ambitious goal of halving road deaths by 2020 and the longer term zero casualty vision.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
Many safety-relevant tasks in control or diagnostics require binary choices such as "conflict versus separation" in air traffic control, "normal versus pathological" when interpreting x-ray pictures, or "permitted versus forbidden" when inspecting airport security scans. Deciders often are uncertain, but nevertheless required to decide between two alternatives, that is, they have not only to decide upon an action, but also about the admissible level of uncertainty. If the accepted level of judgment certainty is not taken into account, the sequence of decisions does not capture the full picture of the underlying decision process. Differences in judgment certainty are relevant, because they reflect not only the adequacy of the human-machine interface that is evaluated, but also the differences in expertise of the decider and the requirements of the actual situation or task. Therefore, capturing both judgment certainty and discrimination performance is essential. A comparison of different human-machine-interfaces (for air traffic control) is used to illustrate a methodological approach, which allows for integrated analyses of decision processes based on receiver-operator-characteristics and practical guidelines for the evaluation of human-machine-interfaces for safety-relevant operation procedures are provided.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
Event Data Recorder (EDR) is an additional function installed in airbag control module (ACM) to record vehicle and occupant information for a brief period of time before, during, and after a crash event. EDRs are now being installed in ACMs by several automakers in the USA and in Japan. The aim of this study is to understand the performance of EDRs for the improvement of accident reconstruction with more reliable information. In the first report of the study, data obtained from EDRs of seven vehicle types were evaluated using 2006-2007 J-NCAP (Japanese new car assessment program) full-lap frontal barrier crash tests and offset frontal deformable barrier crash tests data. For more practical standpoint, we conducted thirteen crash tests reconstructing typical real-world accidents such as single vehicle accidents with barriers or poles, car to car accidents and multi rear-end collisions focusing on Japanese typical accident types. Data obtained from EDRs are compared with data obtained from optical speed sensor, instrumented accelerometers and high speed video cameras. The velocities determined from pre-crash data of EDRs and the maximum change in velocity, delta-V, and delta-V time history data obtained from post-crash data of EDRs are analyzed. The results are as follows: - Pre-crash velocities of EDRs were very accurate and reliable. An average difference between the EDR recording values and reference speeds was 4.2% and a root mean square of the differences was 9.2%. Only two cases resulted large differences for the pre-crash velocity. Both of them were cases with braking prior to the collision. However, another test with braking resulted less difference. The braking condition may influence accuracy of pre-crash velocities. - Maximum delta-Vs obtained from the EDRs showed uncertainty of measurement in several cases in comparisons with the reliable delta-V data. The differences in maximum delta-V were more than 10% in five of twenty-five events data and more than 20% in two of twenty-five events data. An average of the all differences was about 4% and root mean square of the differences was about 11%. Especially large deformation at narrow area may influence accuracy of post-crash delta-V. - Multiple rear-end crash tests were reconstructed using EDRs data as case studies. Some EDRs recorded two events and a time gap between two events, so that these reconstruction case studies were very accurate and reliable. - If though only one of three vehicles in multiple rear end crash was equipped EDR, overview and velocities of all cars may be reconstructed using these limited EDR data. In this case study, leading car- EDR data and middle car- EDR data were valuable. However if only following car was equipped EDR, the reconstruction was not accurate
Among European Countries, Spain first issued a Standard, UNE 135900:2005, further updated in 2008, that deals with homologation and effectiveness evaluation of road restraint systems components designed to reduce harm for bikers impacting on them. An in depth analysis and critical review of this standard is reported in this paper. Beside a close examination of the standard requirements, numerical models of the crash test stated by the standard have been set up and simulated to study the effects of slight speed and approach angle variations on test results, remaining within tolerance gaps allowed by the standard. Model were validated against experimental data. Together with the expected increasing severity of the impact according with speed, a strong influence of approach angle on injury parameters was found. Possible improvements to the norm, in order to make it more robust, are suggested.
Providing effective occupant protection in rollover crashes requires supplying the occupant with a restraint system proven effective in the dynamic rollover accident mode. Preventing ejection and providing restraint sufficient to prevent potentially injurious contacts with both interior and exterior vehicle components is paramount for effective rollover occupant protection. Research has shown that the injury potential can be decreased by closely coupling the occupant to the seat. This paper focuses on the effect of restraint system slack and its relationship to occupant excursion and ejection potential during rollover. Various restraint system configurations are evaluated in rollover-type test environments. A review of prior research is presented prior to presenting new quasi-static vehicle inversion studies conducted with live surrogate occupants. Additionally, dynamic rollover testing utilizing anthropometric test devices (ATDs) is presented. The influence of belt looseness and effects of various restraint designs on the belted occupants' injury potential are discussed.
Since integrated safety systems combine active and passive safety elements in one safety system, it is necessary to define new procedures to evaluate vehicle safety from the overall system point of view. The main goal of the ASSESS project is to develop harmonized and standardized assessment procedures for collision mitigation and avoidance systems. Methods and Data Sources: In ASSESS, procedures are developed for: driver behaviour evaluation, pre-crash system performance evaluation, crash performance evaluation, socio-economic assessment. This paper will concentrate on the activities related to the crash evaluation. The objective is to perform simulations, sled tests and crash tests in order tounderstand the influence of the activation of the pre-crash systems on the occupants" injuries during the crash phase. When a traffic accident is unavoidable, pre-crash systems work on various safety devices in order to improve the vehicle occupants" protection. Braking assistance and adaptive restraint systems are the main pre-crash systems whose effect on the occupants" protection will be described in this paper. Results: The results will be a description of the effect of the activation of the pre-crash systems on the crash phase. Additionally, a set of recommendations for future methodology developments will be delivered. Furthermore, a first approach to the study of the effect of the pre-crash systems activation on the occupants" protection when the impact is unavoidable will be presented. This effect will be quantified using the biomechanical values obtained from the simulation and testing activities and their related injury risks. Simulation and testing activities will consider the following scenarios: - No activation of any pre-crash system, - Activation of one or a combination of several pre-crash systems. In this way, differences in the results obtained from different scenarios will show the effect of each pre-crash system separately during the crash phase. Discussion and Limitations: The set of activities developed in this research project is limited by the fact that with the given resources only a limited number of vehicle models could be investigated. In addition, there are also limitations related to the injury risk curves and the passive safety tools currently on the market. Conclusion and Relevance to session submitted: The paper will present a complete analysis of the effect of pre-crash systems during the crash phase when the impact is unavoidable. Details, limitations and first application experience based on a few examples will be discussed. Currently, there is not any regulation, assessment program, or other similar official procedure able to assess pre-crash systems during the crash phase. This project comprises phases of traffic accidents which have been historically analysed separately, and aims to evaluate them taking into account their interrelationship. ASSESS is one of the first European projects which deals in depth with the concept of integrated safety, defining methodologies to analyse vehicle safety from a global point of view.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
The primary goal of this investigation was to determine the relative risk of traffic accidents in students. In a two year period, a survey amongst 2,325 students was carried out, and 3,645 injuries sustained by students treated at our hospital were analyzed. Moped-riding in adolescents were associated with a 23.75-fold increased risk for injury as compared to biking. Children who ride bicycles have a 2.2-fold increased risk for an injury sustained by traffic accidents compared to pedestrians. None of 50 injured bicycle riders with helmet had an AIS for head injuries of more than 2. 24 of 233 injured bicycle drivers without helmet had an AIS for head injuries of more than 2. The use of a protective helmet significantly reduced the severity of head injuries. The level of awareness towards danger and a history of previous accidents correlate with the likelihood of future accidents. Due to the severity of traffic accidents, more adequate prevention measures (wearing of bicycle helmets and better education for moped riders) are urgently needed.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Aim of the study was to evaluate the protective effect of bicycle helmets particularly considering injuries to the head and to the face. Accidents with the participation of bicyclists which occurred from 2000 to 2007 were chosen from GIDAS. We observed that injuries to the head and face were more severe in the group of non-helmeted riders. There seems to be no significant difference in injuries with AIS 3-6. Altogether 26 cyclists were killed. 2 of them wore a helmet (1% of helmeted cyclists), 24 did not (1% of non-helmeted cyclists). Only one killed rider (without helmet) did not suffer from polytrauma (only head injuries recorded). The findings seem to support the thesis of a preventive effect of the bicycle helmet, however the two groups are different in their characteristics related to riding speed. Necessarily we need a multivariate model to evaluate the effect of helmets.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.
The paper gives an overview of the recent (mostly 2012) figures of killed bus/coach occupants (drivers and passengers) in 27 Member States of the European Union as reported by CARE. The Evolution of the figures of bus/coach occupants killed in road accidents urban, rural without motorway and on motorways from 1991 to 2010 in 15 Member States of the EU supplements this information. More detailed are the figures reported for Germany by the Federal Statistics. The paper displays long-term evaluations (1957 to 2012) for killed, seriously and slightly injured occupants in all kinds of buses/coaches. Midterm evaluations (1995 to 2012) of the figures of fatalities and casualties are displayed for different busses according to their identification of road using as coaches, urban buses, school buses, trolley buses and "other buses". To be able to compare the evolutions of the safety of vehicle occupants it is customary to use different risk indicators. Calculations and illustrations for three often used indicators with their development over time are given: fatalities, seriously injured and slightly injured per 100,000 vehicles registered, per 1 billion (109) vehicle-kilometres travelled and per 1 billion (109) person-kilometres. These indicators are shown for occupants of cars, goods vehicles and buses/coaches. For the period from 1957 until 2012 it is obvious, that for all three vehicle categories analysed there was a clear long-term trend towards more occupant safety in terms of casualties per vehicles registered and per vehicle mileage. This was most significant for car occupants but it can be seen for bus/coach occupants and goodsvehicle occupants as well. Figures of killed occupants and of casualties related to person-kilometres are calculated and displayed for the shorter period 1995 to 2012. Here it becomes obvious that the bus/coach is still the safest mode of transport for the occupants of road vehicles. Graphs for the casualty risk indices still show significantly higher risks for car occupants despite the corresponding curve moved sustainable downwards. It is remarkable, that the risks of being killed or injured for the occupants of urban buses is growing whereas the corresponding risk for the occupants of coaches in line traffic tends downwards. The article ends with a short comparison and discussion of the risk indicators which are actually published for the occupants (driver and passengers) of cars and the passengers of buses/coaches, railroads, trams and airplanes. The interpretation of such information depends on the perception and it seems that for a complete view not only one indicator should be used and the evolutions of the indicator values during longer periods (as displayed with examples in the paper) should also be taken into account.
Data concerning accidents involving personal injury which have been collected in the context of in-depth investigations on scene in the Hannover area since 1973 and in the Dresden area since 1999 represent an important basis for empirical traffic safety research. At national and international level various analyses and comparisons are carried out on the basis of "in-depth data" from the above mentioned investigations. In-depth data play a decisive role e.g. within the validation of EuroNCAP results on secondary safety (crashworthiness) of individual passenger car models. Thus, statistically sound methods of data analysis and population parameter estimation are of high importance. Since the 1st of August 1984 the "in-depth investigations on scene" in the Hannover area have been carried out according to a sampling plan developed by HAUTZINGER in the context of a research project on behalf of BASt. In the meantime a second region of in-depth investigation on scene was added with surveys in Dresden and the surrounding area. Internationally, the acronym GIDAS (German In-Depth Accident Study) is commonly used for the two above mentioned surveys. The objective of a current research project (topic of this contribution) is, among other things, to examine and adjust the previous weighting and expansion method for the two regional accident investigations to the current general conditions.
In the paper it is investigated to what extend one can extrapolate the detailed accident database GIDAS (German In-Depth Accident Study), with survey area Hanover and Dresden region, to accident behavior in other regions and countries within Europe and how such an extrapolation can be implemented and evaluated. Moreover, it is explored what extent of accident data for the target country is necessary for such an extrapolation and what can be done in situations with sparse and low accident information in a target region. It will be shown that a direct transfer of GIDAS injury outcomes to other regions does not lead to satisfactory results. But based on GIDAS and using statistical decision tree methods, an extrapolation methodology will be presented which allows for an adequate prediction of the distribution of injury severity in severe traffic accidents for European countries. The method consists essentially of a separation of accidents into well-described subgroups of accidents within which the accident severity distribution does not vary much over different regions. In contrast the distribution over the various subgroups of accidents typically is rather different between GIDAS and the target. For the separation into the subgroups meaningful accident parameters (like accident type, traffic environment, type of road etc.) have been selected. The developed methodology is applied to GIDAS data for the years 1999-2012 and is evaluated with police accident data for Sweden (2002 to 2012) and the United Kingdom (2004 to 2010). It is obtained that the extrapolation proposal has good to very good predictive power in the category of severe traffic accidents. Moreover, it is shown that iterative proportional fitting enables the developed extrapolation method to lead to a satisfactory extrapolation of accident outcomes even to target regions with sparse accident information. As an important potential application of the developed methodology the a priori extrapolation of effects of (future) safety systems, the operation of which can only be well assessed on the basis of very detailed GIDAS accident data, is presented. Based on the evaluation of the presented extrapolation method it will be shown that GIDAS very well represents severe accidents, i.e. accidents with at least one severely or fatally injured person involved, for other countries in Europe. The developed extrapolation method reaches its limits in cases for which only very little accident information is available for the target region.
A very high service availability is important for the operator and for the user of road tunnels, too. The service availability of a structure is directly related to its quality. The earlier quality assurance measures are being considered during the life cycle, the better a structure of high quality can be guaranteed. Problems which occur during the operation period of a structure often result from design errors or from inadequate realisation during the construction phase. They may also occur as a result of wrongly planned maintenance and refurbishment works. Thus, the transfer of specific data, information and experiences through the whole life cycle is very important. In this context methods of facility management can provide efficient assistance when they have already been used throughout all three classic phases of a structure's life cycle - planning, construction and operation. Finally the tunnel drainage system of German road tunnels is considered as an example as practical application possibility.
Since 2005, the motorcycle crash fatalities in the US exceeded 10% of the overall annual traffic fatalities. Consequently, it has become critical to gain in-depth understanding of the factors and characteristics contributing to motorcycle crashes. Unfortunately, there currently exists no database gathering the necessary information for an in-depth analysis of the US motorcycle crashes. So this study utilizes the NASS/CDS database (National Automotive Sampling System, Crashworthiness Data System) in order to gain insights into the patterns and factors leading to a NASS/CDS motorcycle crash, from 1997 to 2007. NASS/CDS samples about 5,000 passenger car tow-away crashes per year. Each case includes photographs and detailed data on crash and pre-crash characteristics, vehicle types, trajectories, types of impact, and other pertinent roadway and crash scene information, allowing an in-depth investigation of the crash mechanisms. However, the NASS/CDS sampling process specifically focuses on passenger car crashes, so the cases extracted only correspond to crashes in which a passenger vehicle was towed, and a motorcycle was somehow involved. Thus, a by-hand in-depth review of about 200 cases allowed retrieving 106 relevant crashes for this study, tending to represent the severe passenger vehicle(s) versus motorcycle(s) crashes on US roads. The findings lead to the conclusion that these crashes mostly result from the low conspicuity of the motorcycle, and from the inability of the car drivers to fully appreciate and anticipate the behavior of a motorcycle. Indeed, it has been shown that, first, the car drivers involved in these cases did not attempt any avoidance maneuver, second, they were largely of ages under 25, and finally, the majority of the crashes were in an intersection scenario. In addition, the two major scenarios unveiled were the car attempting a left turn from the opposite direction and the car attempting a left turn from the right. The paper mentions several solutions to enhance the motorcycle- conspicuity and to allow the car drivers to better anticipate its behavior, which seem to be key factors in the intersection-related crashes (and more generally in the passenger vehicle(s) versus motorcycle(s) crashes).
In 2011 399 cyclists died in road accidents in Germany and another 76.351 cyclists have been injured. Since 2000 the number of injured or fatally injured cyclists remained on the same high level. Cyclists form 19% of all casualties in German road traffic, although the modal split rate of this transport mode in 2008 was only 10% of trips and resp. 3% of kilometres per day. The high proportion of fatally and seriously injured shows the high vulnerability of cyclists. The demographic shift towards an older population in Germany and the governmental recommendation of increased bicycle use as an ecological, economical and healthy alternative to other modes of transport lead to the assumption that bicycle use especially of elderly people will increase. Based on these facts about the German cyclists' situation a representative survey of 2.000 cyclists was conducted. Results display use patterns and accident involvement on a descriptive level. Overall 7.7% of cyclists report to have been involved in at least one road traffic accident within the last three years. The performed path model analysis reveals an acceptable model fit. Though the explained variance of accident involvement of the applied psychological factors was low, significant relations between several of these factors and especially risky behaviour could be found.
In the context of this study, different data sources for accident research were examined regarding their possible data access and evaluated concerning the individual quality and extent of the data. Analyses of accidents require detailed and comprehensive information in particular concerning vehicle damages, injury patterns and descriptions of the accident sequence. The police documentation supplies the basic accident statistics and is amended in the context of the forensic treatment by further information, e.g. by medical and technical appraisals and witness questionings. As a new approach to the data acquisition for the analysis of fatal traffic accidents, the information was made usable which was collected by the police and by the investigations of the public prosecutor. The best strategy for obtaining reliable, extensive and complete data consists of combining the information from these two sources: the very complete, but elementary statistic data of the Niedersächsisches Landesamt für Statistik (Lower Saxony State Authority of Statistics), based on the police documentation as well as the very extensive accident information resulting from the investigation documentation of the public prosecutor after conclusion of the procedure, the so-called Court Records. Of all 715 fatal traffic accidents, which happened in the year 2003 in the German State of Lower Saxony, 238 cases were selected by means of a statistically coincidental selective procedure based on a statistically representative manner (every third accident). These cases cover the investigation documents of the 11 responsible public prosecutor- offices, which were requested and evaluated while preserving the data security. Of the 238 cases 202 cases were available, which were individually coded and stored in a data base using 160 variables. Thus a data base of a sample of representative data for fatal accidents in Lower Saxony was set up. The data base contains extensive information concerning general accident data (35 variables), concerning road and road surface data (30 variables), concerning vehicle-specific data (68 variables) as well as concerning personal and injury data (27 variables).
Federal highway A 26 in Germany : reinforced dams in soft soils - control method according DIN 1054
(2004)
In 2001 the construction of the Federal Highway A 26 in Lower Saxony (north of Germany) was started. In this area the underground is without any substantial bearing capacity as it consists of soft layers ( clay, peat) with a thickness of up to 12 m. Because it was not possible to exchange the soil neither completely nor partially pre-loading procedure (consolidation method) was chosen for this construction. Short- and long-term stability are ensured by the use of high-tensile fabrics for reinforcement at the dam basis. The vertical and horizontal deformations and the stress changes in the soil, caused by the pre-load procedure, has to be controlled by special geotechnical measurements. Additionally, in the higher parts of the dam the strain behaviour of the high-tensile fabrics is measured. These measurements form the basis for the application of the control method according DIN 1054. In this article, the special circumstances of this project are described. Further on the geotechnical measurements, the winning and evaluation of the necessary parameters of the subsoil, and the consequences of these data for the ongoing of the project are laid down. Intermediate results of the geotechnical measurements are described.
Today's volumes of traffic require more and more responsibility from each individual road user in their interactions. Those who drive motor vehicles have the singular obligation to minimise the risk of accidents and hence the severity of injuries, particularly with a view to the most vulnerable road users such as motor bikes, bikes and pedestrians. Since responsible and pro-active driving depends first and foremost on the visual information relayed by our eyes and the visual channel this requires good command of the traffic and all-round visibility from our driver's seat. Granted that human error can never be fully excluded, improving visibility around the car is nevertheless an urgent priority. To do so, we need to rate visibility in the most realistic driving situations. Since the existing visibility metrics and methodology are not applicable to real-life driving situations, this study aimed at developing a new visibility rating methodology based on real-life accident scenarios. On the basis of the cases documented by the accident research project, this study analysed criteria indicative of diminishing visibility on the one hand and revealing some peculiarities in connection with the visibility issue on the other. Based on the above, the project set out to develop a rating methodology allowing to assess all-round visibility in various road situations taking into account both driver and road geometries. In this context, the assessment of visibility while turning a corner, crossing an intersection and joining traffic on a major road (priority through route) is of major importance. The first tests have shown that critical situations can be avoided by adapting the relevant geometries and technical solutions and that significant improvements of road safety can be derived therefrom.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of synthetic and plastic materials as a material for the interior equipment of buses and coaches because of their ood mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years - also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, the production of smoke, the smoke development and propagation and its toxicity for the people as well as the testing methods and limit values are of interest. For those reasons research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behavior of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and on-board extinguishing equipment were elaborated. At the other hand research is carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. The paper describes which effective and economically reasonable fire safety requirements for interiors of buses would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses.
The improvement of passive car security devices led to a reduction of injuries, especially of the head, the neck and the torso mainly due to the airbag function. The passenger's foot and ankle could not profit from this development. Some investigators even reported a progression of leg injuries (1). In this study, we investigated a current collective of patients with foot and ankle fractures or severe soft tissue injuries in relation with defined crash parameters. Special interest was paid to the car's footwell.
The National Roads Authority in Ireland is responsible for planning and supervision of construction and maintenance works on the National Road network. Its primary function is "to secure the provision of a safe and efficient network of national roads". The population of Ireland has grown rapidly from 3.5 million to 4 million within the past 10 years, and vehicle ownership has also risen rapidly to 2 million vehicles, with 2.2 million drivers. Collisions rates in Ireland are at approximately 1.5 collisions per 1,000 population (in 2002), and 8.4 deaths per 1,000,000 population (in 2003). This ranked 8th out of the 15 countries in the European Union at the time. Ireland- current Road Safety Strategy includes Engineering Targets. These are to complete construction of certain lengths of new motorway, dual carriageway and 2+1 highway, to implement a certain number of accident remedial and traffic calming schemes, and to implement road safety audit on all new schemes. The accident remedial schemes, traffic calming schemes, and road safety audit are all the responsibility of the Road Safety section of NRA. The road safety programme of the NRA is divided into four main areas; a) accident remedial measures at individual sites, b) accident remedial treatment of entire routes, c) traffic calming of towns and villages on main roads, d) road safety audit. Examples of these measures are described. Evaluation of past programmes of single site accident remedial measures show a reduction in collision occurrence at these sites, but the effectiveness and the economic rate of return is decreasing over successive programmes. A similar programme has now been adopted on the rest of the country- road network, on regional and local roads. The programme of remedial treatment of entire routes has only recently started and has not been evaluated. Evaluation of the first programme of traffic calming of towns and villages shows an overall decrease in collisions and their severity, and a small reduction in speed. Road Safety Audit, examining new schemes a number of times during design and after construction, has been standard procedure on the national road network for nearly 6 years. An evaluation is currently underway.
In North America, frontal crash tests in both the regulatory environment and consumer-based safety rating schemes have historically been based on full-width and moderate-overlap (40%) vehicle to barrier impacts. The combination of improved seat-belt technologies, notably belt tensioning and load limiting systems, together with advanced airbags, has proven very effective in providing occupant protection in these crash modes. Recently, however, concern has been raised over the contribution of narrower frontal impacts, involving primarily the vehicle corners, to the incidence of fatality and serious injury as a result of the potential for increased occupant compartment intrusion and performance limitations of current restraint systems. Drawing on data documented in the National Automotive Sampling System (NASS)/ Crashworthiness Data System (CDS) for calendar years 1999 to 2012, the present study examines the characteristics of existing and proposed corner crash test configurations, and the nature of real-world collisions that approximate the test environments. In this analysis, particular emphasis is placed on crash pulse information extracted from vehicle-based event data recorders (EDR's).
In an on-going project since 2005, ADAC has been analyzing accidents documented by the ADAC air rescue service. The knowledge derived from real-life accidents serves as a basis for new test configurations and assessment criteria. In 2007, ADAC began looking into the feasibility of international data collection. The idea of Global Accident Prevention was born. Three European partner clubs have begun pioneering the project (ÖAMTC, ANWB, and RACC). The aim is to set up an international accident research network to provide a steady stream of information on road accidents. The FIA Foundation supports ADAC in developing and coordinating this initiative.
Topics of the status report are: Road accidents in Germany ; Socio-economic costs due to road traffic accidents in Germany , German Road Safety Programme. Finished projects: Turning Assist Systems for Trucks ; Handbook „Accessibility in long-distance bus transport“ ; EU project PROSPECT ; Intersection assistance (Euro NCAP) ; Personal Light Electric Vehicles (PLEV) ; Automatic Emergency Braking for Heavy Goods Vehicles ; KO-HAF ; AFAS ; SENIORS ; Adoption of UN-GTR9-PH2. Ongoing and planned research: Safety potential and testing of reversing assistants for passengers cars (M1) and LGV´s (N1) ; Study on winter tires ; Automatic Emergency Braking for passenger cars ; Motorcyclist-friendly safety barriers ; Active motorcycle safety ; EU-Project PIONEERS ; Friction prediction ; Bus safety: smoke gas toxicity ; HMI aspects on Camera-Monitor-Systems ; Activities with regard to UN R 22 and helmets for S-Pedelecs ; Seriously injured road accident casualties ; UNECE IWG on Deployable Pedestrian Protection Systems (Active bonnets) ; GIDAS – new requirements to address new vehicle technology ; Human Body Modelling ; Child Safety at the UNECE with regard to R 129 ; Development of requirements on automated driving functions for vehicle regulations ; EU-Project L3-Pilot ; Development of evaluation methods for driver interaction with assistance and automation (national research and Euro NCAP) ; EU-Project OSCCAR ; PEGASUS ; Development of basic scenarios for the description of control-relevant requirements for continuous automated vehicle guidance ; EU project HEADSTART ; C-Roads Germany ; Practical Test for the Quality of Congestion-Tail Information ; Research program road safety.
Airbags are, together with the three-point belt, the most effective passive safety equipment of vehicles. However, literature shows that sound pressure levels of up to 170 dB can occur during airbag deployment. A literature review revealed no systematic experimental data on possible hearing loss by airbag deployment, that also takes any other crash accompanied noise into account, such as deformation and impact noise. Also the rising number of airbags per vehicle resulting in a higher number of deployed airbags in an accident was not addressed with respect to hearing loss. Thus, an extensive test matrix of noise measurements during airbag deployments was conducted including onboard measuring during crashes and static measurements. Dynamic and static experiments with single and multiple airbag deployments were conducted. The results of this study show, that in the analyzed crash constellations the acoustic emission of the collision as well as the car deformation can trigger the stapedius reflex before the airbag deployment. The stapedius reflex protects the inner ear at least partially in case of dangerous sound levels. However, it seems that multiple airbag deployments in a short sequence pose a considerable risk for hearing impairments despite the fully contracted stapedius muscle. Further and in line with Price et al. (2013) it was found that the risk of hearing loss is lower with closed windows. The analysis of patient and accident data showed no link between airbag deployment and hearing loss. This might be caused by low case numbers of reported hearing loss problems up to now. In conclusion the results show that a singular analysis of the sound pressure of airbag deployments without crash accompanied noises is not sufficient as the protective effect of the stapedius reflex is neglected. Still, successive airbag deployments in a short timeframe raise the risk of hearing loss. Further investigation on hearing impairment due to airbag deployment and triggering of the stapedius reflex is needed and the data acquisition of accidents and patients should consider hearing loss aspects.
In India, heavy truck crashes on national highways account for a number of fatalities. But due to lack of in-depth crash data, detailed analysis is not possible to determine injury mechanisms, and to identify infrastructure, vehicle and human factors affecting these crashes. Over the past two years, researchers in India have established a crash investigation network, with the co-operation of the police and hospitals, to conduct crash investigations and in-depth crash data collection on national highways in the state of Tamil Nadu. This pioneering effort has resulted in the development of a heavy truck crash investigation methodology, the outcome of which is scientific and reliable crash data that has been able to provide good insight into truck crashes and their causes. This paper explains the need for truck crash investigations, the methodology, conclusions of the data analyzed up to date, and the need to focus on truck driver working conditions.
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
[Introduction:] A large number of road users involved in road traffic crashes recover from their injuries, but some of them never recover fully and suffer from some kind of permanent disability. In addition to loss of life or reduced quality of life, road accidents carry many and diverse consequences to the survivors such as legal implications, economic burden, job absences, need of care from a third person, home and vehicle adaptations as well as psychological consequences. Within an EU funded project MOVE/C4/SUB/2011-294/SI2.628846 (REHABIL AID) these consequences were analyzed more detailed.
The misuse of CRS (child restraint system) is one of the most urgent problems in connection of child safety in cars. Numerous field studies show that more than two thirds of all CRS are used in a wrong way. This misuse could lead to serious injuries for the children. Surprisingly the quality of CRS use is coded much better in accident data (e.g. GIDAS) than the results of observatory field studies show. It is expected that misuse of CRS was not detected by the accident teams in a large number of the cases. An essential part in improving child seats and their usability is the knowledge of the relation between misuse and resulting injuries. For that the analysis and experimental reconstruction of accidents is an important part. For allowing an exact experimental accident reconstruction, it is necessary to have detailed information about the securing situation of the child and about the installation of the CRS in the car.
This study updates previous IIHS studies comparing estimated delta Vs for crash tested vehicles to the distribution of estimated delta Vs in the National Automotive Sampling System (NASS) Crashworthiness Data System (CDS). The delta V estimates for 232 frontal crash tests at 64.4km/h into a deformable barrier with 40 percent overlap are compared with estimates from frontal offset crashes in the 1997-2004 NASS database. All delta V estimates were based on SMASH, the delta V estimating program used by NASS since 1997. Results indicated that for all vehicles tested by IIHS, SMASH delta Vs were, on average, 32 percent lower than impact speeds and about 28 percent lower than the expected delta V. Almost 80 percent of all real-world frontal crashes resulting in AIS 3+ injuries and just over 60 percent of all fatal crashes occur at or below the average estimated delta V calculated for crash tested vehicles.