Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (63) (entfernen)
Schlagworte
- Test method (63) (entfernen)
Institut
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
Um die Automobilhersteller zu animieren, mehr als die gesetzlich geforderte Sicherheit anzubieten, haben strengere Versuche im Rahmen des Verbraucherschutzes in den letzten Jahren nicht nur in den USA, sondern auch in Europa deutlich an Bedeutung zugenommen. Besonders Initiativen aus England ist es zu verdanken, dass sich heute die Testverfahren nach dem sogenannten Euro NCAP, dem European New Car Assessment Programme, durchgesetzt haben. Diese Entwicklung wurde auch von der Europäischen Kommission unterstützt. Ziel des Euro NCAP ist es, die unabhängige und objektive Bewertung des Sicherheitsniveaus von Fahrzeugen zu einer transparenten und leicht verständlichen Verbraucherberatung zu fördern. Weiterhin sollen objektive Bewertungsverfahren entwickelt werden, um die Fahrzeughersteller zu ermutigen, die Fahrzeuge sicherer zu machen. Im Beitrag wird auf die Struktur des Euro NCAP sowie auf seine Arbeitsweise eingegangen. Vorgestellt werden ferner bisherige Testphasen mit Fahrzeugen deutscher Hersteller oder Tochtergesellschaften sowie deren Bewertung.
Ausgehend von den Unfalldaten der letzten Jahre wird die Bedeutung von Fußgängerunfällen im Unfallgeschehen dargestellt. Betrachtet man die bei Unfällen getöteten Verkehrsteilnehmer, so sind am häufigsten Personen in Kraftfahrzeugen betroffen. Am zweithäufigsten werden, gemäß der Unfallstatistik, Fußgänger getötet. Eine Möglichkeit zur Verbesserung des Schutzes von Fußgängern und anderen sogenannten "ungeschützten Verkehrsteilnehmern" im Falle einer Kollision mit einem Kraftfahrzeug sind Maßnahmen am Fahrzeug. Um die Wirksamkeit derartiger Maßnahmen zu beurteilen, wurde durch das EEVC (European Enhanced Vehicle-Safety Committee) ein Prüfverfahren entwickelt. Es handelt sich dabei um ein Komponentenprüfverfahren, mit dem die Frontstruktur von Fahrzeugen, die bei einer Kollision mit einem Fußgänger hauptsächlich betroffen ist, geprüft wird. Es werden keine den gesamten Menschen repräsentierende Dummies verwendet, stattdessen werden Prüfkörper, die einzelne Körperteile simulieren, eingesetzt. Dieser EEVC Vorschlag wird geschildert. Darüber hinaus wird über Aktivitäten außerhalb des EEVC berichtet, sowie über den aktuellen Stand der Bemühungen der Europäischen Kommission in Bezug auf den Fußgängerschutz, die derzeit, auf Grundlage des Prüfvorschlages des EEVC, einen Vorschlag für eine Europäische Richtlinie erarbeitet.
Allein im Netz der Bundesfernstraßen sind etwa 35.000 Brücken mit einer Fläche von 25 Millionen Quadratmetern enthalten. Ihr Wiederbeschaffungswert beträgt etwa 70 Milliarden DM. Es wird über die notwendigen Aktivitäten zur Erhaltung dieser für die Aufrechterhaltung des auf den Bundesfernstraßen rollenden Verkehrs besonders wichtigen Bauwerke berichtet. Aufgrund des weiter stärker werdenden Verkehrs, der zunehmenden Fahrzeuggewichte sowie der wachsenden Anzahl von Schwertransporten unterliegen insbesondere die älteren Bauwerke größerer Beanspruchung, als man bei ihrer Planung in Rechnung stellen musste. Hinzu kommt die natürliche Alterung aus sonstigen äußeren Einflüssen wie Temperatur, Witterung und erhöhter Umweltbelastung. Die Verwendung von Auftausalzen führt insbesondere bei älteren Brückenüberbauten zu Korrosionsschäden an der Bewehrung des Betons. Durch die Entwicklung eines Bauwerks-Management-Systems (BMS) wird die Verbesserung der Erhaltung von Brücken und sonstigen Ingenieurbauten angestrebt. Der Aufbau und die Wirkungsweise des BMS werden dargelegt. Des Weiteren werden die schon seit langem eingeführten Prüfvorschriften für Bauwerke im Zuge von Straßen und Wegen (DIN 1076) sowie gängige Prüfverfahren beschrieben.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
In der Europäischen Union (EU) gab es 1999 circa 1,3 Millionen Straßenverkehrsunfälle mit Personenschaden, wobei circa 42.000 Personen getötet wurden. Ziel der EU ist es diese Zahl auf 25.000 im Jahr 2010 zu senken. Die EEVC befasst sich bereits seit Anfang der 80er Jahre mit der Thematik Fußgängerschutz in verschiedenen Arbeitsgruppen. Im Dezember 1998 legte die EEVC-Arbeitsgruppe 17 "Fußgängersicherheit" ihren Abschlussbericht vor, in dessen Anhang ein Prüfverfahren zum fahrzeugseitigen Fußgängerschutz enthalten ist. Dieses Prüfverfahren wird vorgestellt. Es basiert auf Komponententests. Unterschieden werden drei Prüfkörperarten und insgesamt vier Prüfkörper. Aus wissenschaftlicher Sicht und aus Sicht der Unfallforschung empfiehlt die EEVC-Arbeitsgruppe 17 eine umfassende Einführung des vorgeschlagenen Prüfverfahrens mit allen Prüfkörpern, gegebenenfalls in Form einer stufenweisen Einführung.
The Swedish National Road Administration (SNRA), the Japanese Automobile Research Institute (JARI) and the Federal Highway Research Institute (BASt) are co-operating in the International Harmonized Research Activities on Intelligent Transportation Systems (IHRA-ITS). Under this umbrella a joint study was conducted. The overall objective of this study was to contribute to the definition and validation of a "battery of tools" which enables a prediction and an assessment of changes in driver workload due to the use of in-vehicle information systems (IVIS) while driving. In this sense \"validation\" means to produce empirical evidence from which it can be concluded that these methods reliably discriminate between IVIS which differ in terms of relevant features of the HMI-design. Additionally these methods should also be sensitive to the task demands imposed on the driver by the traffic situation and their interactions with HMI-design. To achieve these goals experimental validation studies (on-road and in the simulator) were performed in Sweden, Germany and Japan. As a common element these studies focused on the secondary task methodology as an approach to the study of driver workload. In a joint German-Swedish on-road study the Peripheral Detection Task (PDT) was assessed with respect to its sensitivity to the complexity of traffic situations and effects of different types of navigation systems. Results show that the PDT performance of both the German and the Swedish subjects reflects the task demands of the traffic situations better than those of the IVIS. However, alternative explanations are possible which will be examined by further analyses. Results of this study are supplemented by the Japanese study where informational demands induced by various traffic situations were analysed by using a simple arithmetic task as a secondary task. Results of this study show that relatively large task demands can be expected even from simple traffic situations.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
When the EEVC proposed the full-scale side impact test procedure, it recommended that consideration should be given to an interior headform test in addition. This was to evaluate areas of contact not assessed by the dummy. EEVC Working Group 13 has been researching the parameters of a possible European headform test procedure in four phases. Earlier stages of the research have been presented at previous ESV conferences. The conclusions from these have suggested that the US free motion headform should be used in any European test procedure and that it should be a free flight test, not guided. This research has now culminated in proposals for a European test procedure. This paper presents the proposed EEVC side impact interior headform test procedure, giving the rationale for the test and the first results from the validation phase of the test protocol.
The European Enhanced Vehicle-safety Committee (EEVC) Working Group 13 for Side Impact Protection has been developing an Interior Headform Test Procedure to complement the full-scale Side Impact Test Procedure for Europe and for the proposed IHRA test procedures. In real world accidents interior head contacts with severe head injuries still occur, which are not always observed in standard side impact tests with dummies. Thus a means is needed to encourage further progress in head protection. At the 2003 ESV-Conference EEVC Working Group 13 reported the results on Interior Headform Testing. Further research has been performed since and the test procedure has been improved. This paper gives an overview of its latest status. The paper presents new aspects which are included in the latest test procedure and the research work leading to these enhancements. One topic of improvement is the definition of the Free Motion Headform (FMH) impactor alignment procedure to provide guidelines to minimize excessive headform chin contact and to minimize potential variability. Research activities have also been carried out on the definition of reasonable approach head angles to avoid unrealistic test conditions. Further considerations have been given to the evaluation of head airbags, their potential benefits and a means of ensuring protection for occupants regardless of seating position and sitting height. The paper presents the research activities that have been made since the last ESV Conference in 2003 and the final proposal of the EEVC Headform Test Procedure.
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
Zur Ergänzung der bestehenden Routineverfahren in der forensischen Blutalkoholanalytik wurde ein massenspektrometrisches Verfahren mit d6-Ethanol als internem Standard entwickelt. Ziel war die Anwendung eines beweissicheren Bestimmungsverfahrens, bei dem Ethanol über die Retentionszeit und Substanzeigenschaften identifiziert wird. Die Pilotstudie belegt, dass die forensische Blutalkoholbestimmung durch Anwendung eines gaschromatographischen und massenspektrometrischen Verfahrens mit Dampfraumanalyse routinemäßig möglich ist. Im Gegensatz zum GC- und ADH-Verfahren ist die massenspektrometrische Blutalkoholbestimmung beweissicher. Die Autoren empfehlen die Aufnahme in die Richtlinien zur Bestimmung der Blutalkoholkonzentration für forensische Zwecke. Die Arbeit wurde vom Bund gegen Alkohol und Drogen im Straßenverkehr e.V. (B.A.D.S.) unterstützt.
Diese Studie erfolgte als eine erste Prüfung der Frage, ob 0,1 Promille als Sicherheitszuschlag für eine Bestimmung eines Blutalkoholwertes von 0,1 Promille aus Gründen der Messunsicherheit angebracht und ausreichend ist. Beides trifft zu. Obwohl zur Zeit der Studie noch nicht bei oder unter 0,2 Promille kalibriert wurde, bestimmten alle Labors eine Blutalkoholkonzentration von 0,08 Promille mit einem Wert unter 0,18 g/L (Cmax ADH: 0,15 g/L = CmaxGC: 0,15 g/L = Blutalkoholkonzentration (BAK) von 0,12 Promille). Es bestand kein Bias zwischen beiden Verfahren. Festgestellte Standabweichungen: ADH: 0,021 g/L, GC: 0,025 g/L. Ein Sicherheitszuschlag von 0,1 Promille auf 0,1 Promille umfasst demnach vier Standardabweichungen und bietet für die neue Regelung im Paragrafen 24 Straßenverkehrsgesetz (StVG) bei der richtliniengemäß ausgeführten forensischen Blutalkoholbestimmung genügend Analysensicherheit.
Die Begutachtung der Fahreignung beinhaltet in Deutschland neben einer medizinischen Untersuchung und einer psychologischen Exploration gegebenenfalls auch die Anwendung anlassbezogener verhaltenswissenschaftlicher/psychologischer Testverfahren. Diese stellen keine isolierte Maßnahme dar, sondern sind Bestandteil eines Begutachtungsprozesses. Dabei stellt der sachgerechte Gebrauch von so genannten Grenzwerten unter Berücksichtigung der Einzelfallgerechtigkeit und der Einhaltung des Grundsatzes der Verhältnismäßigkeit eine unabdingbare Voraussetzung dar. Testwerte sind nicht absolut, sondern relativ und üben von daher einen eher geringen Einfluss auf das Gutachtenergebnis in Bezug auf eine Prognose des Verkehrsverhaltens aus. Im Bereich des Verkehrsverhaltens kommt es nicht entscheidend darauf an, ob eine im Milli- oder Nanobereich exakte Messgenauigkeit erreicht wird, sondern wie die verkehrsmedizinischen, verkehrspsychologischen, technischen und anderen Sachverständigen mit dem Messwert fachlich umgehen. So müssen im Bereich der Begutachtung der Fahreignung tätige psychologische und medizinische Sachverständige in der Lage sein, Befunde im Einzelfall fehler-, mangel- sowie widerspruchsfrei zu interpretieren. Dies beinhaltet auch, sich mit den Ergebnissen eines psychologischen Testverfahrens fach- und sachgerecht auseinanderzusetzen, nach Kompensationsmöglichkeiten zu suchen und gegebenenfalls eine psychologische Fahrverhaltensbeobachtung durchzuführen. Bei grenzwertigen Vorgaben handelt es sich nicht um "Cut-Offs", sondern um "kritische Grenzwerte", die im Zusammenhang mit mehreren anderen Faktoren zu werten sind.
Die aktuellen Richtlinien zur Bestimmung der Blutalkoholkonzentration (BAK) für forensische Zwecke (BAK-Richtlinie, 2007) lassen unter bestimmten Bedingungen auch zwei verschiedene gaschromatographische Analysen anstatt der häufig angewandten Kombination Gaschromatographie und enzymatische Methode ADH zur Bestimmung des Blutalkoholgehaltes zu. Untersucht wurde die Messpräzision zweier gaschromatographischer Verfahren bei der Alkoholanalytik im Vergleich zur häufiger angewandten Methodenkombination. In mehr als 50 Prozent der Fälle hat sich bei den verglichenen Methodenkombinationen ein identischer Mittelwert ergeben. Ansonsten waren die Abweichungen gering. Damit werden die hohen Anforderungen, die an die forensische Blutalkoholbestimmung gestellt werden, durch die modernen Laborautomaten erfüllt.
Der Beitrag berichtet in einem ersten Teil über die in den Niederlanden angewendeten Inspektionstechniken zur Feststellung von Schäden (Rissen) bei orthotropen Stahlfahrbahnplatten und in einem zweiten Teil über die Instandsetzung der Moerdijkbruecke mit einer zusätzlichen Deckschicht aus bewehrtem hochfesten Stahlfaserbeton. Die Ausführungen zu den Inspektionstechniken umfassen die visuelle Inspektion, magnetische Inspektion, Farbeindringprüfung, Ultraschallprüfung und Diffraktionseffekt bei Anstrahlen von Fehlern (Time of Flight Diffraction (TOFD)) sowie radiographische Untersuchungen und das Wirbelstromverfahren. Für jede dieser Methoden wird ihre Wirkungsweise, Handhabung und der Anwendungsbereich angegeben. Die Moerdijkbrücke ist eine der meistbefahrenen Brücken in den Niederlanden mit einem erheblichen Schwerverkehrsaufkommen und weist etliche Schäden am Deckblech auf. Die bisher durchgeführte Instandsetzung durch Ausbessern der Längsschweissnähte führte nicht zum erhofften Erfolg. Der Bauherr entschloss sich daher, die Gussasphaltschicht durch einen bewehrten hochfesten Stahlfaserbeton mit einer Dicke von 5 cm mit Verbund zum Stahldeckblech zu ersetzen. Die Spannungen im Deckblech konnten auf diese Weise um einen Faktor 4 bis 5 reduziert werden. Die Methode reagiert jedoch empfindlich auf Abweichungen der Mischungsverhältnisse des Betons und der Viskosität.
Im Oktober 2007 wurde die Rügenbrücke, eine der längsten Hochbrücken Europas, für den Verkehr freigegeben. Der Beitrag befasst sich mit den Erfahrungen, die bei Planung und Bau dieses bemerkenswerten Bauwerks gemacht wurden, insbesondere hinsichtlich der vielen bautechnischen Innovationen bei dem Schlüsselbauwerk des Brückenzuges, der 570 m langen Schrägseilbrücke über den Ziegelgraben. Eine der wesentlichen Erstanwendungen für Deutschland betraf die Ausführung der Schrägseile mit Litzenbündeln des Systems DYNA Grip der SUSPA DSI. Wegen des aus Gründen des Vogelschutzes erforderlichen Mindestdurchmessers der Seile von 12 cm waren vollverschlossene Seile aus ingenieurtechnischen und wirtschaftlichen Gründen benachteiligt, sodass sich der Bauherr für Seile aus Litzenbuendeln entschied. Die Schrägseilbrücke über den Ziegelgraben wird schon jetzt als modernes Wahrzeichen der Stadt Stralsund empfunden. Sie passt sich gestalterisch hervorragend in die Umgebung ein und beeinträchtigt auch nicht die zum Weltkulturerbe zählende Altstadt von Stralsund. Besonders besticht das Bauwerk durch seine Leichtigkeit und die Einpassung der Formen der Bauteile, zum Beispiel wegen der tropfenfoermigen Gestaltung des Pylons und der Pfeiler, in das maritime Umfeld. Da die verwendeten Schrägseil-Litzenbündel noch nicht allgemein bauaufsichtlich zugelassen sind, kam der Qualitätssicherung für die Seile in allen Stufen der Planung, Fertigung, Montage und Bauwerksprüfung eine herausragende Bedeutung zu. Der zugehörige Qualitätssicherungsplan wird im Bericht ausführlich mit den wesentlichen \"schrägseilspezifischen\" Maßnahmen beschrieben. Schwingungen und Ermüdungsbeanspruchungen der Seile durch Fahrverkehr und Wind liessen sich durch einen mehrstufigen, kontinuierlich verdichteten Planungsprozess unter Nutzung von Versuchsdaten und Messungen am Bauwerk wirkungsvoll beherrschen. Aus Sicht der Bauwerksprüfung bestanden anfänglich Bedenken wegen der Erreichbarkeit der bis in 80 m Höhe über dem Brückendeck gespannten Schrägseile und der nicht direkt zugänglichen Litzen innerhalb des Hüllrohres sowie der Verankerungen. Daher wurden alle verfügbaren Prüfverfahren für Schrägseile an der Rügenbrücke getestet. Daraus ergab sich eine Prüfmatrix aus Prüfverfahren, Prüfmittel und Prüfumfang für die gesamte Nutzungsdauer. Zusammenfassend wird festgestellt, dass bei der Ziegelgrabenbrücke Schrägseile aus Litzenbündeln eine den vollverschlossenen Seilen ebenbürtige Bauart darstellen.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.
Für den Einsatz im Erdbau des Straßenbaus müssen die eingesetzten Geokunststoffe hohen Qualitätsansprüchen genügen. Das Straßenbauregelwerk ist durch die Veröffentlichung der "Zusätzlichen Technischen Vertragsbedingungen und Richtlinien für Erdarbeiten im Straßenbau" (ZTV E-StB 09) in dieser Hinsicht nun vollständig, so dass eine lückenlose Nachverfolgung der Produkte von der Herstellung über die Lieferung bis zum Einbau möglich ist. Wichtig ist jedoch die Einhaltung der Vorschriften und Anforderungen, angefangen beim Hersteller über den Lieferanten, über den Auftragnehmer bis hin zum Auftraggeber, um einen hohen Qualitätsstandard des Produktes und der fertigen Leistung zu garantieren. Hersteller, deren Produkte einer freiwilligen Überwachung unterliegen, können diese Produkte mit einem Qualitätssiegel kennzeichnen und liefern zusammen mit der CE-Kennzeichnung ein Produktzertifikat. Da in diesem Fall auf die Baustoffeingangsprüfung verzichtet werden kann, reduziert sich der finanzielle und zeitliche Prüfaufwand und es wird ein reibungsloser Bauablauf erzielt.
Durch die Einführung der Bauproduktenrichtlinie und der nationalen Umsetzung in das Bauproduktengesetz kam es zur Erarbeitung einer ganzen Reihe von europäischen Prüf- und Anforderungsnormen für Straßenbauprodukte. Dazu zählen auch die Erhaltungsbauweisen Oberflächenbehandlung und Dünne Asphaltdeckschicht in Kaltbauweise. Dieser europäische Normungsprozess wird kontinuierlich weitergeführt. So sind vor allem bei der Bauweise Dünne Asphaltdeckschicht in Heißbauweise auf Versiegelung neuere Aktivitäten zu verzeichnen, aber auch die älteren Prüfnormen stehen vor ihrer regulären periodischen Überprüfung. In naher Zukunft wird mit der Bauproduktenverordnung ein neuer europäischer Rechtsakt erscheinen, der möglicherweise eine zusätzliche Dynamik in den Prozess bringt, der momentan noch nicht absehbar ist.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
Im Rahmen eines von der Bundesanstalt für Straßenwesen (BASt) initiierten Forschungsvorhabens (15.449/2007/ERB: "Prüfverfahren zur Beurteilung der Lebensdauer von Kunststoffdichtungsbahnen für Straßentunnel") wurden anhand von Untersuchungen an Kunststoffdichtungsbahnen (KDB) auf Basis von Polyolefinwerkstoffen die Möglichkeiten der Beurteilung der oxidativen Langzeitbeständigkeit sondiert. Im Mittelpunkt stand die Erprobung des Autoklaventests in Anlehnung an DIN EN ISO 13438 (Methode C1/C2) an ausgewählten, für den Tunnelbau repräsentativen marktüblichen KDB-Produkten. Die Untersuchungen im Autoklaven bei erhöhten Temperaturen (60 -°C, 70 -°C und 80 -°C) und Sauerstoffdrücken (11, 21 und 51 bar) wurden durch vergleichende Versuche im Wärmeschrank (Ofen) bei erhöhter Temperatur (85 -°C) in Anlehnung an DIN EN 14575 ergänzt. Die KDB-Produkte wurden außerdem einer eingehenden Materialcharakterisierung (Zugprüfung, OMA, DSC) unterzogen. Weiterhin wurden Bauwerksdaten recherchiert und auf ihre Nutzbarkeit zur Bewertung und Prüfbarkeit der Langzeitbeständigkeit von KDB in Tunneln betrachtet. Ziel war auch, die Anwendbarkeit des bisher vorgeschlagenen Extrapolationsmodells zur Auswertung der Ergebnisse von Autoklaventests an im Tunnelbau marktüblichen Produkten für Nutzungsdauern über 25 Jahre zu überprüfen und zur Entwicklung eines geeigneten Prüfverfahrens beizutragen. Der Beitrag geht auf Ergebnisse des Vorhabens ein und zeigt erste Schlussfolgerungen und weiteren Untersuchungsbedarf auf. Die Ergebnisse werden in den "Empfehlungen zu Dichtungssystemen im Tunnelbau EAG-EDT" des Arbeitskreises 5.1 "Kunststoffe in der Geotechnik und im Wasserbau" berücksichtigt, deren 2. Auflage in Vorbereitung ist. Aspekte des thermischen Verhaltens der eingesetzten Werkstoffe sowie mögliche Anpassungen der Prüfrandbedingungen für die Autoklaventests werden ergänzt und Hinweise zur Interpretation von Prüfergebnissen gegeben. Außerdem wurden inzwischen ausgehend von den Ergebnissen des Forschungsvorhabens erste Autoklaven-Ringversuche in drei Prüfinstitutionen initiiert.
Untersuchungen an in situ gealterten Kunststoffdichtungsbahnen aus Abdichtungen von Straßentunneln
(2011)
Tunnel in Spritzbetonbauweise werden in der Regel mit einem Abdichtungssystem aus Kunststoffdichtungsbahnen (KDB) gegen das anstehende Bergwasser abgedichtet. Zur Gewährleistung der Dauerhaftigkeit und Gebrauchstauglichkeit aber auch der Verkehrssicherheit (z.B. Gefahr der Glatteisbildung in undichten Tunneln) müssen die Tunnelabdichtungen aus KDB dabei über die gesamte Nutzungsdauer des Bauwerks von in der Regel 100 Jahren zuverlässig Ihre Funktion erfüllen. An der Entwicklung von Prüfverfahren zum Nachweis dieser Nutzungsdauer wird zurzeit national und international intensiv geforscht. Zur Verifizierung und Kalibrierung dieser Prüfverfahren können Untersuchungen an in situ gealterten KDB-Proben aus bestehenden Straßentunneln sehr nützlich sein. Im vorliegenden Beitrag werden erste Ergebnisse der Untersuchungen zu Materialeigenschaften von ausgebauten KDB Proben aus älteren Straßentunneln vorgestellt. Im Rahmen eines Forschungsprojektes der Bundesanstalt für Straßenwesen (BASt) wurden bereits zahlreiche Materialproben aus bestehenden Straßentunneln, die aktuell bautechnisch nachgerüstet werden, entnommen und untersucht. Bei der Entnahme der KDB-Proben wurde parallel auch die Bergwassertemperatur gemessen und an Bergwasserproben der Chemismus analysiert. Soweit möglich wurden die Produktdaten des Anlieferungs- bzw. Einbauzustandes beim Hersteller oder Bauherrn recherchiert, um so die Veränderungen der mechanischen Eigenschaften durch die in situ Alterung bewerten zu können. Die ermittelten mechanischen Eigenschaften nach Alterung wurden mit den Anforderungen damals gültiger und aktueller Regelwerke verglichen.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
The German highway network hast o face new challenges in the near future, e.g. increasing traffic density and loads, climate change effects and new quality requirements regarding sustainability. It is necessary to come up with foresighted concepts in the present to be prepared for these challenges. Therefore it is important to adapt and enhance innovative attempts, which take changing impacts into account. One goal of these efforts is the development of adaptive systems for the provision of information and a holistic evaluation in real time. The paper describes the recent research and developments on a system for information and holistic evaluation in real time, taking into account sensor networks, evaluation procedures and their implementation in existing maintenance and inspection strategies.
Für die Instandsetzung von schadhaften Betonfahrbahnplatten mittels "Heben und/oder Festlegen" werden in zunehmendem Maße Injektionsmaterialien aus Kunststoff verwendet. Aktuell existieren für die Prüfung und Bewertung derartiger Materialien mittels straßenbauspezifischer Kennwerte jedoch noch keine hinlänglichen Erfahrungen und Prüfvorschriften. In Laborversuchen wurden nunmehr geeignete Prüfungen und Auswertalgorithmen entwickelt und zweckgerichtete Festigkeitskennwerte an ausgesuchten Materialien bestimmt sowie erste Anforderungswerte formuliert. Zudem wurden die Wirksamkeit und die Dauerhaftigkeit von Unterpressungen im Hinblick auf das verwendete Injektionsmaterial in Praxisversuchen überprüft. Aus den Ergebnissen der Tragfähigkeitsmessungen ließ sich vorerst folgern, dass durch das Unterpressen von Fahrbahnplatten die Tragfähigkeits- und Lagerungsbedingungen signifikant verbessert werden können. Unterschiede in der kurzfristigen Wirksamkeit - im Hinblick auf das verwendete Injektionsmaterial - konnten hierbei nicht explizit deduziert werden. Vielmehr zeigte sich, dass die Dauerhaftigkeit maßgeblich von den vorliegenden Randbedingungen, das heisst, faktisch von der richtigen Auswahl des Materials abhängt.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
Having a look at safety to traffic and the prevention of accidents it can be observed that technical improvements in active safety of vehicles have let to various positive effects in this area. Among other components the tyre-road-contact takes a key role in the development of active safety technologies. All forces in accelerating, breaking and vehicle guidance have to be transmitted through the tyre-road contact area by friction forces. A common way to characterize a friction process is to identify the coefficient of friction μ between two touching materials. Even though there are several approaches to experimentially characterise road surfaces, no standard method exists. In this paper an overview of existing test methods is given. Furthermore the preliminary design of a newly developed portable test device with its possibility to investigate the tyre-road-friction of arbitrary roads or even places of accidents is shown.
Automotive interiors have long been a potentially injurious impact area to occupants during accidents, especially in the absence of adequate padding. The U.S. Federal Motor Vehicle Safety Standard (FMVSS) 201, Occupant Protection in Interior Impact, outlines test procedures and performance criteria in order to mitigate potentially injurious head impacts to interior surfaces. FMVSS 201 specifies a finite set of impact locations and applies to passenger vehicles of a specified year range and with a gross vehicle weight rating less than 10,000 lb. In this paper, two head impact test methodologies are presented, a pendulum-test device and a Free Motion Headform (FMH) launching device, which allows for dynamic, repeatable impact evaluation of various vehicle interior surfaces and their impact attenuation abilities. The presented testing includes multiple series that evaluate the effect of differing vehicle upper interior padding on occupant head injury. One study in particular, analyzes a head impact to the side header of a heavy truck (not included in FMVSS 201) during a 90 degree rollover. Additionally, two other series of tests are presented which assess the injury reduction effect of side airbags to near side as well as far side occupants in a side impact scenario. Lastly, a forensic analysis is presented which evaluates two possible head impact locations experienced in a real world accident by analysis of the resulting interior compartment damage utilizing the FMH launching device test method. The data collected and presented includes accelerometer instrumentation and high speed video analysis. These studies demonstrate that adequate padding and airbags are very effective at mitigating head injury potential at impact speeds of 12-25 mph (19-40 kph).
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
Um ein zuverlässiges Straßennetz aufrechtzuerhalten, ist es notwendig, neue innovative Ansätze in das Erhaltungsmanagement der Brückenbauwerke im Bundesfernstraßennetz zu integrieren und weiterzuentwickeln. Ergänzend zu den turnusmäßigen Bauwerksprüfungen nach DIN 1076 wird daher ein adaptives Konzept bereitgestellt, das es ermöglichen soll zum einen Zustandsveränderungen frühzeitig zu erfassen und zu bewerten und zum anderen mit Hilfe von erfassten Einwirkungen und Widerständen zukünftige Zustandsentwicklungen zu prognostizieren. Die zu konzipierenden Systeme setzen sich im Wesentlichen aus der Datenerfassung mit Hilfe von Sensorik und den zur echtzeitnahen Verwendung und Bewertung notwendigen Modellen zusammen. Im Rahmen mehrerer Forschungsprojekte wurden einzelne Bausteine eines solchen adaptiven Systems erarbeitet.
Due to the publication of guidelines in Germany the possibility exists to offer analytical designed construction works within an alternative proposal. But the extent to which the test specimen production influences the design relevant properties (for the same asphalt mixture) is not sufficiently investigated at present. Objective of this research project was to determine the design relevant asphalt properties by tests and do comparative considerations on two selected locations within the renewal of a federal trunk road (Germany). For the comparative consideration of the design relevant asphalt properties mixture samples were taken during paving and afterwards drill cores were taken at the same locations. Fatigue tests and tests to determine the stiffness were conducted with the Indirect Tensile Test (ITT). Then design calculations having regard to the test results were performed. At this different bearing conditions of the asphalt package were considered. The calculated fatigue conditions were comparative evaluated and they are presented and discussed in this paper.
Für die rechnerische Dimensionierung der Betondecken im Oberbau von Verkehrsflächen für den Neubau sowie die Erneuerung nach RDO-Beton 09 ist die statische Spaltzugfestigkeit an der unteren beziehungsweise unteren und oberen Scheibe des Betonzylinders beziehungsweise Bohrkerns entsprechend der Vorgaben der AL Sp-Beton zu bestimmen. Aufgrund der unzureichenden Kenntnis der Präzision dieses Prüfverfahrens wurden mit einem breit aufgestellten Ringversuch die statistischen Kennwerte an Labor- und Bestandsbetonen unter Vergleichs- und Wiederholbedingungen auf der Grundlage des FGSV-Merkblatts über die statistische Auswertung von Prüfergebnissen ermittelt. Für eine möglichst gute statistische Absicherung nahmen an dem Ringversuch dreizehn erfahrene Prüfstellen teil. Zur Abdeckung des vielschichtigen Einsatzes des Prüfverfahrens erfolgte der Ringversuch an acht Prüflosen. Dabei berücksichtigen einerseits die Prüflose 1 und 2 mit den im Transportbetonwerk hergestellten Betonzylindern die Erst-/Eignungsprüfung und das darauf aufbauende Prüflos 3 mit Bohrkernen aus einer im Feldversuch hergestellten Fahrbahnplatte mit gleicher Betonrezeptur die Übereinstimmungskontrolle bei Neubaumaßnahmen. Andererseits findet der Einsatz des Prüfverfahrens bei der Restsubstanzbewertung von Betonfahrbahnplatten bei den Prüflosen 4 bis 7 mit den Bohrkernen aus vier in Waschbetonbauweise ausgeführten Fahrbahnplatten Berücksichtigung. Das zusätzlich aufgenommene Prüflos 8 mit einem Labormörtel dient der Herausarbeitung des Materialeinflusses auf die Präzision der Spaltzugfestigkeitsprüfung. Zusammenfassend kann festgestellt werden, dass die Präzision der in der AL Sp-Beton beschriebenen Spaltzugfestigkeitsprüfung mit einem Variationskoeffizienten von weniger als 10 % unter Wiederhol- und Vergleichsbedingungen hinreichend genau ist. Der geringe Unterschied zwischen den Variationskoeffizienten unter Wiederhol- und Vergleichsbedingungen lässt zusätzlich den Schluss zu, dass der Einfluss des unterschiedlichen Personals und der verschiedenartigen Prüftechniken bei den einzelnen Prüfstellen relativ gering ist. Die im Rahmen des Ringversuchs gewonnenen Erkenntnisse haben bereits partiell Eingang in die Normung gefunden.
Bitumen ist ein Erdölprodukt mit einer komplexen chemischen Zusammensetzung. Durch die Auswahl der zur Herstellung verwendeten Rohöle und die Art des Raffinerieprozesses werden die Zusammensetzung und die resultierenden chemisch-physikalischen Eigenschaften bestimmt. Für die Untersuchung von Bitumen steht heute eine Vielzahl von leistungsfähigen Methoden der modernen instrumentellen Analytik zur Verfügung. Das Hauptproblem bei der Analyse von Bitumen besteht in der Auftrennung des Stoffgemisches. Chromatographische Verfahren bieten generell die besten Voraussetzungen derartige Trennaufgaben zu bewältigen. So ermöglicht die TLC-FID-Methode die quantitative Bestimmung der Stoffgruppen der Aliphaten, Aromaten, Harze und Asphaltene. Dagegen ermöglicht die klassische Dünnschichtchromatographie, die in der Vergangenheit ausschließlich zum Nachweis von teerhaltigen Bindemitteln eingesetzt wurde, eine einfache und schnelle Möglichkeit eine chemische Charakterisierung von Bitumen in Form eines "Fingerprints" vorzunehmen. Dem Anspruch eine möglichst exakte und vollständige Beschreibung der chemischen Zusammensetzung von Bitumen zu erhalten, stehen Begrenzungen hinsichtlich der Wirtschaftlichkeit und Schnelligkeit der Verfahren gegenüber. Dennoch ist es möglich, mit einem relativ begrenzten Aufwand wertvolle Informationen über die chemische Beschaffenheit zu erhalten.
Tunnel in Spritzbetonbauweise werden in der Regel mit einem Abdichtungssystem aus Kunststoffdichtungsbahnen (KDB) gegen das anstehende Bergwasser abgedichtet. Die Tunnelabdichtungen aus KDB müssen dabei über die gesamte Nutzungsdauer des Bauwerks von in der Regel 130 Jahren zuverlässig ihre Funktion erfüllen. Ein einfacher Austausch der KDB oder der Einbau einer gleichwertigen Alternative ist in der Regel nicht, oder nur mit erheblichem Aufwand möglich. Bislang existieren national und international keine abgesicherten Prüfkriterien, die eine Bestimmung der Langzeitbeständigkeit von KDB über die geforderte Nutzungsdauer von mindestens 100 Jahren ermöglichen. Im vorliegenden Beitrag werden Untersuchungsergebnisse eines BASt Forschungsprojektes präsentiert, in dem Prüfkriterien für die Abschätzung der Langzeitbeständigkeit von KDB aus PVC-P hergeleitet werden. In diesem Projekt werden verschiedene marktübliche KDB für die Tunnelabdichtung mit einem beschleunigten Prüfverfahren "Lagerung in heißem Wasser" systematisch auf ihr Alterungsverhalten hin untersucht. Das hierfür verwendete Immersionsprüfverfahren wurde neu entwickelt und basiert auf der SIA V 280 (Prüfung Nr. 13) und DIN EN 14415. Ziel der Untersuchungen ist es, die erforderlichen Prüfkriterien zu definieren, die für eine praxisgerechte Abschätzung der Nutzungsdauer von mindestens 100 Jahren erforderlich sind. Hierfür werden beispielsweise die Einlagerungsdauer, die Einlagerungstemperatur und das Prüfmedium strukturiert untersucht. Zum Vergleich der Prüfergebnisse aus dem Immersionsprüfverfahren werden Untersuchungen an ausgebauten KDB Proben aus 2 älteren Straßentunneln herangezogen. Die Ergebnisse des Forschungsvorhabens sollen in die Fortschreibung des nationalen Regelwerks für den Straßentunnelbau (TL/TP KDB) einfließen.
Euro NCAP will start to test pedestrian Automatic Emergency Braking Systems (AEB) from 2016 on. Test procedures for these tests had been developed by and discussed between the AsPeCSS project and other initiatives (e.g. the AEB group with Thatcham Research from the UK). This paper gives an overview on the development process from the AsPeCSS side, summarizes the current test and assessment procedures as of March 2015 and shows test and assessment results of five cars that had been tested by BASt for AsPeCSS and the respective manufacturer. The test and assessment methodology seems appropriate to rate the performance of different vehicles. The best test result - still one year ahead of the test implementation - is around 80%, while the worst rating result is around 10%. Other vehicles are between these boundaries.
A methodology to derive precision requirements for automatic emergency braking (AEB) test procedures
(2015)
AEB Systems are becoming important to increase traffic safety. Test procedures in testing for consumer information, manufacturer self-certification and technical regulations are used to ensure a certain minimum performance of these systems. Consequently, test robustness, test efficiency and finally test cost become increasingly important. The key driver for testing effort and test costs is the required repeatable accuracy in a test design - the higher the accuracy, the higher effort and test costs. On the other hand, the performance of active safety systems depends on time discretization in the environment perception and other sub-systems: for instance, typical sensors supply information with a cycle time of 50 - 150 ms. Time discretization results in an inherent spread of system performance, even if the test conditions are perfectly equal. The proposed paper shows a methodology to derive requirements for a test setup (e.g. test repeats, use of driving robots, ...) as function of AEB system generation and rating method (e.g. Euro NCAP points awarded, pass/fail, ...). While the methodology itself is applicable to AEB pedestrian and AEB Car-Car scenarios, due to the lack of sufficient test data for AEB Car-Car, the focus of this paper is on AEB pedestrian scenarios. A simulation model for the performance of AEB Pedestrian systems allows for the systematic variation of the discretization time as well as test condition accuracy. This model is calibrated with test results of 4 production vehicles for AEB Pedestrian, all fully tested by BASt according to current Euro NCAP test protocols. Selected parameters to observe the accuracy of the test setup in case of pedestrian AEB is the calculated impact position of pedestrian on the vehicle front (as if no braking would have occurred), and the test vehicle speed accuracy. These variable was shown in real tests to be repeatable in the range of ± 5 cm and ± 0,25 km/h, respectively, with a fully robotized state of the art test setup. The sensitivity of AEB performance (measured in achieved speed reduction as well as overall rating result according to current Euro NCAP rating methods) towards discretization and the sensitivity of performance towards test accuracy then is compared to identify economic yet robust test concepts. These comparisons show that the available repeatability accuracy of current test setups is more than sufficient for today's AEB system capabilities. Time discretization problems dominate the performance spread especially in test scenarios with a limited pedestrian dummy reveal time (e.g. child behind obstruction, running adult scenarios with low car speeds). This would allow to increase test tolerances to decrease test cost. A methodology which allows to derive the required tolerances in active safety tests might be valuable especially for NCAPs of emerging countries that do not have the necessary equipment (e.g. driving robots, positioning units) available for the full-scale and high tolerance EuroNCAP active safety procedures yet still want to rate active safety systems, thus improving the global safety.
Accidents between right turning trucks and straight riding cyclists often show massive consequences. Accident severity is much higher than in other accidents. The situation is critical especially due to the fact that, in spite of the six mirrors that are mandatory for ensuring a minimum field of sight for the truck drivers, cyclists in some situations cannot be seen or are not seen by the driver. Either the cyclist is overlooked or is in a blind spot area that results from the turning manoeuvre of the truck and its articulation if it is a truck trailer or truck semitrailer combination. At present driver assistance systems are discussed that can support the driver in the turning situation by giving a warning when cyclists are riding parallel to the truck just before or in the turning manoeuvre. Such systems would generally bear a high potential to avoid accidents of right turning trucks and cyclists no matter if they ride on the road or on a parallel bicycle path. However, performance requirements for such turning assist systems or even test procedures do not exist yet. This paper describes the development of a testing method and requirements for turning assist systems for trucks. The starting point of each development of test procedures is an analysis of accident data. A general study of accident figures determines the size of the problem. In-depth accident data is evaluated case by case in order to find out which are representative critical situations. These findings serve to determine characteristic parameters (e.g. boundary conditions, trajectories of truck and cyclist, speeds during the critical situation, impact points). Based on these parameters and technical feasibility by current sensor and actuator technology, representative test scenarios and pass/fail-criteria are defined. The outcome of the study is an overview of the accident situation between right turning trucks and straight driving cyclists in Germany as well as a corresponding test procedure for driver assistance systems that at this first stage will be informing or warning the driver. This test procedure is meant to be the basis for an international discussion on introducing turning assist systems in vehicle regulations.
During the past five years, a Euro NCAP technical working group on pedestrian safety has been working on improving test and assessment procedures for enhanced passive pedestrian safety. After harmonizing the tools and procedures as much as possible with legislation, the work was mainly focused on the development of grid procedures for the pedestrian body regions head, upper leg with pelvis and lower leg with knee. Furthermore, the test parameters for the head and the upper leg were revised, a new lower legform impactor was introduced and the injury thresholds were adjusted or, where necessary, the injury criteria were changed. Finally, the assessment limits and colour scheme were refined, widening the range and adding two more colours in order to provide a more detailed description of the pedestrian safety performance. By abstaining from an assessment based on a worst point selection philosophy, the improved test point determination procedures that were introduced during the years 2013 and 2014 give a more homogeneous, high resolution picture of the pedestrian safety performance of the vehicle frontends. By using a uniform grid for each test zone approximately 200 test points, evenly distributed within each area, can now be assessed per vehicle. The introduction of the flexible pedestrian legform impactor in 2014 enables a more realistic injury prediction of the knee and the tibia using a biofidelic test tool. With the new upper legform test that has been launched in 2015 the assessment in that area is now focusing on the injured body region instead of the injury causing vehicle part and thus is aligned with the approach in the remaining body regions head and lower leg. At the same time, a monitoring test with the headform impactor against the bonnet leading edge is closing the possible gap between the test areas to identify injury causing vehicle parts that moved out of focus due to the introduction of the new upper legform test. The paper describes the new test and assessment procedures with their underlying philosophy and gives an outlook in terms of open issues, specifying the needs for further improvement in the future. In parallel to the work of the pedestrian subgroup, a Euro NCAP working group on heavy vehicles introduced a set of protocol changes in 2011 that were related to the assessment of M1 vehicles derived from commercial vehicles, with a gross vehicle weight between 2.5 and 3.5 tons and 8 or 9 seats. The paper also investigates the applicability of the new pedestrian test and assessment procedures to heavy vehicles.
Die Ermittlung einer voraussichtlichen Restnutzungsdauer von Verkehrsbefestigungen und somit der Abschätzung des Eingreifzeitpunktes für eine grundhafte Erneuerung ist ohne die Kenntnis der strukturellen Substanz nur sehr unzureichend zu bewerkstelligen. Mit Vorliegen des Entwurfes zu den "Richtlinien zur Bewertung der strukturellen Substanz des Oberbaus von Verkehrsflächen in Asphaltbauweise" (RSO Asphalt) ist zwar ein hierfür nutzbares Verfahren verfügbar, allerdings basiert dieses auf der Analyse von Laborversuchen an den aus Streckenabschnitten zu entnehmenden Bohrkernen, wodurch eine netzweite Anwendung nicht praktikabel ist. Um trotzdem einen umfassenden Einsatz zu ermöglichen und eine deutliche Verbesserung gegenüber bisherigen Verfahren herbeizuführen, können aber begründete Annahmen zu den Materialkennwerten getroffen werden. Alle weiteren Eingangsdaten des Verfahrens decken sich mit denen des bisherigen. Deren Vollständigkeit und Plausibilität muss zukünftig mehr Bedeutung zugemessen werden.
Automatische Lenkfunktionen sind abgesehen von korrigierenden Lenkeingriffen entsprechend der UN-Regelung Nr. 79 bisher nur in einem Geschwindigkeitsbereich bis 10 km/h erlaubt. Die Weiterentwicklung der Technik im Bereich der Fahrerassistenzsysteme und der Automatisierung der Fahraufgabe wuerden es jedoch technisch erlauben, automatische Lenkfunktionen auch bei höheren Geschwindigkeiten einzusetzen. Neben einem Zugewinn an Komfort wird von diesen Systemen auch ein Beitrag zur Erhöhung der Verkehrssicherheit erwartet. Dieses Verkehrssicherheitspotenzial wird man jedoch nur ausschöpfen können, wenn die automatisierten Lenksysteme entsprechend gestaltet sind. Insbesondere sollten mögliche Risiken auf Grund automatischen Lenkens minimiert sein. Aus diesen Gründen laufen derzeit Arbeiten auf UNECE-Ebene, die Regelung Nr. 79 über einheitliche Bedingungen für die Genehmigung der Fahrzeuge hinsichtlich der Lenkanlage in Bezug auf automatische Lenkfunktionen (ACSF = Automatically Commanded Steering Functions) zu überarbeiten, um diese unter bestimmten Bedingungen auch bei höheren Geschwindigkeiten genehmigen zu können. Der vorliegende Beitrag reflektiert diese Arbeiten und stellt die Entwicklung der technischen Anforderungen an automatisches Lenken und der für die fahrzeugtechnischen Vorschriften vorgesehenen Testprozeduren dar.
PROSPECT (Proactive Safety for Pedestrians and Cyclists) is a collaborative research project involving most of the relevant partners from the automotive industry (including important active safety vehicle manufacturers and tier-1 suppliers) as well as academia and independent test labs, funded by the European Commission in the Horizon 2020 research program. PROSPECT's primary goal is the development of novel active safety functions, to be finally demonstrated to the public in three prototype vehicles. A sound benefit assessment of the prototype vehicle's functionality requires a broad testing methodology which goes beyond what has currently been used. Since PROSPECT functions are developed to prevent accidents in intersections, a key aspect of the test methodology is the reproduction of natural driving styles on the test track with driving robots. For this task, data from a real driving study with subjects in a suburb of Munich, Germany was used. Further data from Barcelona will be available soon. The data suggests that intersection crossing can be broken down into five phases, two phases with straight deceleration / acceleration, one phase with constant radius and speed turning, and two phases where the bend is imitated or ended. In these latter phases, drivers mostly combine lateral and longitudinal accelerations and drive what is called a clothoid, a curve with curvature proportional to distance travelled, in order to change lateral acceleration smoothly rather than abrupt. The data suggests that the main parameter of the clothoid, the ratio distance travelled to curvature, is mostly constant during the intersections. This parameter together with decelerations and speeds allows the generation of synthetic robot program files for a reproduction of natural driving styles using robots, allowing a much greater reproducibility than what is possible with human test drivers. First tests show that in principle it is possible to use the driving robots for vehicle control in that manner; a challenge currently is the control performance of the robot system in terms of speed control, but it is anticipated that this problem will be solved soon. Further elements of the PROSPECT test methodology are a standard intersection marking to be implemented on the test track which allows the efficient testing of all PROSPECT test cases, standard mobile and light obstruction elements for quick reproduction of obstructions of view, and a concept for tests in realistic surroundings. First tests using the PROSPECT test methodology will be conducted over the summer 2017, and final tests of the prototype vehicles developed within PROSPECT will be conducted in early 2018
The UN Regulation No. 79 is going to be amended to allow automatically commanded steering functions (ACSF) at speeds above 10 km/h. Hence, requirements concerning the approval of automatically performed steering manoeuvres have to be set in order to allow safe use of automatic steering on public roads as well as improve overall road safety for the driver and the surroundings. By order of the German Federal Ministry of Transport and Digital Infrastructure (BMVI), BASt developed and verified physical test procedures for automatic steering to be implemented in UN Regulation No. 79. The usability of currently available test tools was examined. The paper at hand describes these test procedures and presents results from verification tests. The designated tests are divided in three sections: functionality tests, verifications for the transition of control and emergency tests. System functionality tests are auto matic lane keeping, automatic lane change and an automatic abort of an initiated lane change due to traffic. Those tests check if the vehicle remains in its lane (under normal operating conditions), is able to perform safe automatic lane change manoeuvres and if it considers other road users during its manoeuvres. Transition tests examine the vehicle's behaviour when the driver fails to monitor the system and in situations when the system has to hand over the steering control back to the driver. For instance these tests provoke driver-in-the-loop requests by approaching system boundary limitations, like missing lane markings, surpassing maximum lateral acceleration in a bend or even a major system failure. Even further the driver and his inputs are monitored and if the system detects that he is overriding system actions or contrary want to quit the driving task and unfastens the seat belt, it has to shut down and put the human back into manually control and the responsibility of driving. The last series of test consists of two emergency situations in which the system has to react to a time critical event: A hard decelerating vehicle and a stationary vehicle in front both with no lane change possibility for the ACSF vehicle. Some of the tests, especially the emergency manoeuvres, require special target vehicles and propulsion systems. Since no fully automatic steering vehicles are available, a current Mercedes E-Class with Mercedes' "drive pilot" system was used. It was shown that the vehicle is automatically able to brake to a full stop towards a static Euro NCAP target from partial-automatic driving at 90 km/h, that it could brake towards a rapidly decelerating lead vehicle when travelling at 70 km/h, that it was able during partially automatic driving to remain in its lane in normal operation conditions and to perform a automatic (driver initiated) lane change while surveilling the driver- activities.
Schutz von schwächeren Verkehrsteilnehmern: kommende Anforderungen aus Gesetzgebung und Euro NCAP
(2017)
Systeme der aktiven Fahrzeugsicherheit, insbesondere Notbremsassistenzsysteme und automatische Notbremssysteme, haben in den letzten zwei Dekaden große technische Fortschritte gemacht, und das im Wesentlichen ohne "Druck" von Gesetzgeber oder unabhängigen Testorganisationen " diese können aber durch passende Anforderungen den Vormarsch der Systeme in die Breite und die Ausnutzung von ansonsten für den Hersteller vielleicht nicht wirtschaftlichen Potentialen unterstützen. Dieser Bericht hat das Ziel, einen Überblick über die kommenden Anforderungen an Schutzsysteme für schwächere Verkehrsteilnehmer zu geben und diese Anforderungen in den Kontext Euro NCAP (=welchen Einfluss haben diese Anforderungen auf die Gesamtbewertung?) sowie Gesetzgebung (schwächere Anforderungen, aber dafür ein Markteintrittskriterium) zu stellen: - Anforderungen und Testprozeduren für Notbremsassistenz Fahrradunfälle 2018 und 2020 in Euro NCAP; - Anforderungen und Testprozeduren für Notbremsassistenz bei Nachtunfällen mit Fußgängern in Euro NCAP 2018; - Anforderungen und Testprozeduren für Abbiegeassistenzsysteme zum Schutz von Radfahrern in Unfallsituationen mit rechtsabbiegenden Lkw innerhalb der Fahrzeugtypgenehmigung.
Except for corrective steering functions automatic steering is up to now only allowed at speeds up to 10 km/h according to UN Regulation No. 79. Progress in automotive engineering with regard to driver assistance systems and automation of driving tasks is that far that it would be technically feasible to realise automatically commanded steering functions also at higher vehicle speeds. Besides improvements in terms of comfort these automated systems are expected to contribute to road traffic safety as well. However, this safety potential will only be exhausted if automated steering systems are properly designed. Especially possible new risks due to automated steering have to be addressed and reduced to a minimum. For these reasons work is currently ongoing on UNECE level with the aim to amend the regulation dealing with provisions concerning the approval of steering equipment. It is the aim to revise requirements for automatically commanded steering functions (ACSF) so that they can be approved also for higher speeds if certain performance requirements are fulfilled. The paper at hand describes the derivation of reasonable system specifications from an analysis of relevant driving situations with an automated steering system. Needs are explained with regard to covering normal driving, sudden unexpected critical events, transition to manual driving, driver availability and manoeuvres to reach a state of minimal risk. These issues form the basis for the development of test procedures for automated steering to be implemented in international regulations. This holds for system functionalities like automatic lane keeping or automatic lane change as well as for addressing transition situations in which the system has to hand over steering to the driver or addressing emergency situations in which the system has to react instead of the driver.
Für eine Reihe von EU Regelungen im Bereich Fahrzeugsicherheit erlaubt eine Verordnung bereits seit dem Jahr 2010 virtuelles Testen für die Typzulassungsprüfung. Technische Details bzw. konkrete Prozeduren für spezifische Regelungen sind in dieser Verordnung jedoch nicht enthalten. Das Hauptziel des europäischen Projekts IMVITER (lmplementation of Virtual Testing in Safety Regulations) war es, basierend auf der neuen Verordnung ein virtuelles Testverfahren auszuarbeiten und dabei offene Fragen zu berücksichtigen. Um die im Projekt-Konsortium unter Berücksichtigung der Anliegen aller Interessensgruppen wie Autohersteller, Zulassungsbehörden und technischer Dienste erarbeiteten offenen Punkte zu adressieren, wurde ein generisches Flussdiagramm entwickelt, das den Ablauf einer virtuell basierten Typprüfung darstellt. ln diesem Diagramm ist der virtuelle Typgenehmigungsprozess in drei aufeinander folgende Phasen aufgeteilt, die Verifikations-, Validierungs- und Typgenehmigungsphase. Von entscheidender Bedeutung ist die Phase der Validierung des Simulationsmodells, für die im IMVITER-Projekt eine Methodik vorgeschlagen wurde. Mit der im Projekt vorgeschlagenen Validierungsmethode ist kein Austausch des Simulationsmodells zwischen Fahrzeughersteller und technischem Dienst notwendig, so dass die Vertraulichkeit von Betriebsgeheimnissen nicht gefährdet ist. Zur Validierung des Modells werden jedoch immer Versuche notwendig sein. Dies gilt sowohl für die Überpruefung von passiven als auch aktiven Fahrzeugsicherheitssystemen. Eine zusammenfassende Betrachtung der Erfahrungen aus dem IMVITER-Projekt ergab, dass mit der Einführung von virtuellem Testen keine Erhöhung der Anforderungen an die Fahrzeugsicherheit bzgl. bestehender Regelungen verbunden sein sollte. Jedoch werden auch weiterhin neue zusäztliche Regelungen erforderlich sein, da sich das Unfallgeschehen und die Fahrzeugtechnologie weiterentwickeln und ändern werden. Diese sollten von Beginn an die Möglichkeiten des virtuellen Testens nutzen, insbesondere bei Testverfahren für neue Technologien, z.B. aktiver Fahrzeugsicherheitssysteme. Hier bieten virtuelle Testverfahren nicht nur eine Kosten- oder Zeitersparnis, sondern ermöglichen teilweise erst die sinnvolle Abprüfung von neuen Sicherheitssystemen, die mit aktuellen auf Hardware-Test basierenden Verfahren überhaupt nicht möglich wären.
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
Test and assessment procedures for passive pedestrian protection based on developments by the European Enhanced Vehicle-safety Committee (EEVC) have been introduced in world-wide regulations and consumer test programmes, with considerable harmonization between these programmes. Nevertheless, latest accident investigations reveal a stagnation of pedestrian fatality numbers on European roads running the risk of not meeting the European Union- goal of halving the number of road fatalities by the year 2020. The branch of external road user safety within the EC-funded research project SENIORS under the HORIZON 2020 framework programme focuses on investigating the benefit of modifications to pedestrian test and assessment procedures and their impactors for vulnerable road users with focus on the elderly. Injury patterns of pedestrians and cyclists derived from the German In-Depth Accident Study (GIDAS) show a trend of AIS 2+ and AIS 3+ injuries getting more relevant for the thorax region in crashes with newer cars (Wisch et al., 2017), while maintaining the relevance for head and lower extremities. Several crash databases from Europe such as GIDAS and the Swedish Traffic Accident Data Acquisition (STRADA) also show that head, thorax and lower extremities are the key affected body regions not only for the average population but in particular for the elderly. Therefore, the SENIORS project is focusing on an improvement of currently available impactors and procedures in terms of biofidelity and injury assessment ability towards a better protection of the affected body regions, incorporating previous results from FP 6 project APROSYS and subsequent studies carried out by BASt. The paper describes the overall methodology to develop revised FE impactor models. Matched human body model and impactor simulations against generic test rigs provide transfer functions that will be used for the derivation of impactor criteria from human injury risk functions for the affected body regions. In a later step, the refined impactors will be validated by simulations against actual vehicle front-ends. Prototyping and adaptation of test and assessment procedures as well as an impact assessment will conclude the work of the project at the final stage. The work will contribute to an improved protection of vulnerable road users focusing on the elderly. The use of advanced human body models to develop applicable assessment criteria for the revised impactors is intended to cope with the paucity of actual biomechanical data focusing on elderly pedestrians. In order to achieve optimized results in the future, the improved test methods need to be implemented within an integrated approach, combining active with passive safety measures. In order to address the developments in road accidents and injury patterns of vulnerable road users, established test and assessment procedures need to be continuously verified and, where needed, to be revised. The demographic change as well as changes in the vehicle fleet, leading to a variation of accident scenarios, injury frequencies and injury patterns of vulnerable road users are addressed by the work provided by the SENIORS project, introducing updated impactors for pedestrian test and assessment procedures.
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.
The Netherlands is on the way to change its existing skid resistance measuring method for its highway network from the Dutch RAW 72, a longitudinal force method, to the Sideway Force method. This method is described in the Technical Specification 15901-8 (SKM device) as well as 15901-6 (SCRIM device) and is in use in 9 European countries. The CEN TC 227 WG5 on Surface Characteristics is currently working on combining of these two technical Specifications into a European standard for Sideway-Force (SWF) measurement devices. The idea of this change in the Netherlands was perceived in 2013 and since then a lot of meetings have been held with the different Dutch decision makers as well as with countries which currently operate SWF devices. There was an intensive exchange of knowledge about these devices and their corresponding quality assurance systems, because the Netherlands wanted to incorporate and rely on an existing system of a neighbor country without losing their present level of quality. The Netherlands has therefore decided to incorporate the German SKM approach. The network monitoring with the new system will start in 2017. To ensure the quality of skid resistance measurements and further cooperation in this field, it has been decided to initiate an alliance between BASt and the Dutch road owner Rijkswaterstaat (RWS). This alliance will facilitate an exchange of research activities, calibration of the Dutch systems according to the existing German Standard as well as control measurements with a BASt-device on the Dutch network during the network monitoring. During 2016 also comparative measurements will be performed on a network level with the current Dutch device and with an SKM device to determine a conversion between the two and to be able to define new threshold values.
Knowledge of material properties is of great importance when developing new types of concrete and construction methods for road building, and for quality control and quality assurance. Physical material characteristics are likewise the basis for dimensioning and assessing the residual substance of concrete pavements. One relevant characteristic when examining thermally induced stress and deformation is the coefficient of thermal expansion (CTE) of concrete. This indicator, for example, significantly influences the longitudinal expansion of the pavement system as well as the degree of curling of slabs and joint movements. Extensive tests were conducted during the technical engineering assessment of the structural substance of concrete pavements in the German motorway network, including tests to determine the CTE of existing types of concrete. Because no standardised procedure currently exists in Germany for using tests to determine the CTE of concrete, the initial task was to develop a suitable test procedure from a road-building perspective, taking consideration of the national prevailing structural conditions. This article presents the results of selected status analyses, in which the CTE was determined for a total of 656 individual samples. The values calculated for the top and bottom drilled core layer are in the range 8.9 – 13.2 x 10-6/K, whereby the average CTE assumes a value of 10.7 x 10-6/K. The deviations of the CTEs from the bottom and top drilled core layer are in principle significantly below the limitation to a maximum of 2.50 x 10-6/K recommended in literature.
Im Jahr 2009 wurde CEN/TC 396 „Erdarbeiten“ mit der Zielsetzung gegründet, erstmalig europäische Normen für Erdarbeiten zu erarbeiten. Durch eine einheitliche Grundlage für Erdarbeiten in den EU-Ländern sollen Handelshemmnisse vermieden und die Nutzung und Schonung natürlicher Ressourcen verbessert werden. Länder mit bestehenden nationalen Regelwerken, z. B. im Eisenbahn- oder Straßenbau, können diese weiterhin anwenden und gleichzeitig Erfahrungen mit der europäischen Norm sammeln. Gespiegelt werden die Arbeiten vom NA 005-05-22 AA „Erdarbeiten (SpA zu CEN/TC 396 und CEN/TC 396/WG 1 bis WG 8), Gemeinschaftsausschuss mit FGSV“ im DIN-Normenausschuss Bauwesen. Von allen Beteiligten wurde in den letzten Jahren großes Engagement in die Erarbeitung und Begleitung der ersten sechs Teile der Normenreihe EN 16907 eingebracht. Ihre Veröffentlichung wird im April 2019 erwartet. Bereits 2017 wurde DIN CEN/TS 17006 (DIN SPEC 1035), Erdarbeiten – Flächendeckende dynamische Verdichtungskontrolle (FDVK) veröffentlicht. Der Norm-Entwurf zu DIN EN 16907-7, Erdarbeiten – Teil 7: Hydraulische Einbringung von mineralischen Abfällen befindet sich derzeit in der CEN-Umfrage. Diese erste Generation der europäischen Erdbaunormen stellt im Ergebnis den derzeitigen Konsens im europäischen Raum dar und geht den ersten Schritt in Richtung Harmonisierung. Zudem wird eine Übersicht über die nationale Praxis der verschiedenen Länder gegeben. Sie bietet somit für ausführende Unternehmen eine Hilfestellung, da diese einen Überblick über die Regelwerke der jeweiligen Länder erhalten. In neuen Arbeitsgruppen des CEN/TC 396 haben bereits die Arbeiten an weiteren Normungsvorhaben begonnen. Ein Technical Report (CEN/TR) zum Einsatz von sekundären Rohstoffen befindet sich in der Erarbeitung, und eine Arbeitsgruppe befasst sich mit erdbauspezifischen Prüfverfahren. Diese neuen Themen werden ebenfalls durch den NA 005-05-22 AA gespiegelt. Für die nächste Generation europäischen Erdbaunormen wird der NA 005-05-22 AA gemeinsam mit den Gremien der Forschungsgesellschaft für Straßen- und Verkehrswesen (FGSV) eine auf den Erfahrungen mit der neuen Normenreihe basierende Liste mit Änderungserfordernissen vorbereiten, die bei der nächsten turnusmäßigen Überprüfung im Sommer 2023 von deutscher Seite eingebracht werden soll.
Die Kenntnis von Materialeigenschaften spielt bei der Entwicklung oder Optimierung von Betonen und Bauweisen für den Straßenbau sowie der Qualitätskontrolle und -sicherung eine bedeutende Rolle. Gleichermaßen bilden physikalische Materialkennwerte die Grundlage für die rechnerische Dimensionierung und die Restsubstanzbewertung von Betonfahrbahndecken. Einen relevanten Kennwert bei der Untersuchung thermisch induzierter Spannungs- und Verformungszustände stellt der thermische Ausdehnungskoeffizient von Beton dar. Dieser beeinflusst beispielsweise maßgeblich das Längsdehnungsverhalten des Deckensystems sowie das Ausmaß von Plattenkrümmungen und Fugenbewegungen. Im Zuge der systematischen Weiterentwicklung der rechnerischen Dimensionierung aber auch im Zusammenhang mit der gezielten Verbesserung der Gebrauchseigenschaften von Fahrbahndecken gilt es zu hinterfragen, ob lastunabhängige Formänderungseigenschaften, wie z. B. der thermische Ausdehnungskoeffizient der verwendeten Betone, aktuell ausreichend Beachtung finden, ob allgemeine Literaturwerte für die heutigen Fahrbandeckenbetone stets Gültigkeit besitzen und ob deren Implementierung in moderne Rechenmodelle zu validen Ergebnissen führt. Für eine empirische Herangehensweise ist die Verfügbarkeit adäquater Prüfverfahren von entscheidender Bedeutung. In Deutschland existiert aktuell jedoch kein standardisiertes oder genormtes Verfahren für die prüftechnische Bestimmung des thermischen Ausdehnungskoeffizienten von Beton. Daher wurden unter Beachtung straßenbauspezifischer Gesichtspunkte zwei Prüfansätze entwickelt, die in diesem Beitrag vorgestellt und hinsichtlich möglicher Messunsicherheiten und Messungenauigkeiten diskutiert werden. Außerdem erfolgt die Darstellung ausgewählter Ergebnisse aus Analysen an Bestandsbetonen aus dem BAB-Netz. Im Ergebnis sollen die Untersuchungen einen Beitrag zur Schaffung der prüftechnischen Voraussetzungen für eine abgesicherte Quantifzierung der thermischen Dehnung von Fahrbahndeckenbetonen leisten.
The Intersection 2020 project was initiated to develop a test procedure for Automatic Emergency Braking systems in intersection car-to-car scenarios to be transferred to Euro NCAP. The project aims to address current road traffic accidents on European roads and therefore sets a priority of the identification of the most important car-to-car accidents and Use Cases. Taking into account technological and practical limitations, Test Scenarios are derived from the Use Cases in a later stage of the project. This paper presents parts of a larger study and provides an overview of common car-to-vehicle(at least four wheels) collision types at junctions in Europe and specifies seven Accident Scenarios from which the three scenarios “Straight Crossing Paths (SCP)”, “Left Turn Across Path – Opposite Direction Conflict (LTAP/OD)” and “Left Turn Across Path – Lateral Direction (LTAP/LD)” are most important due to their high relevance regarding severe car-to-car accidents. Technical details about crash parameters such as collision and initial speeds are delivered. The analysis work performed is input for the definition and selection of the Use Cases as well as for the project’s benefit estimation. The numbers of accidents and fatalities in accidents at intersections involving a passenger car were shown per intersection type. In both statistics, it was found that accidents at crossroads and T- or staggered junctions are of highest relevance, followed by roundabouts. Focusing on accidents at intersections between one passenger car and another road user shows that around one-third of all accidents and related fatalities could have been assigned to car-to-PTW accidents and one-fifth of all accidents and fatalities to car-to-car accidents. Regarding car-to-car accidents with at least serious injury outcome 38% out of 34,489 car-to-car accidents happened at intersections. These figures correspond to 18% of the fatalities (4,236 fatalities in total). Considering all intersection types, around half of all related accidents happened in urban environments whereas this number decreased to one-third of all fatalities. Further, the proportion of road fatalities per country occurring at intersections varies widely across the EU. Also, there are proportionately more fatalities in daylight or twilight conditions at junctions. Use Cases are supposed to be derived from Accident Scenarios and by adding detailed information for example about the road layout, right-of-way and the vehicle trajectories prior to the collision. Instead of applying cluster algorithms to the accident data, a pragmatic approach was finally preferred to create them. Note: Use Cases serve as an intermediate step between the Accident Scenarios and the Test Scenarios which describe the actual testing conditions. Finally, 74 Use Cases were identified. This large number indicates the complexity of intersection crashes due to the combination of several parameters.
Bicyclists and pedestrians belong to the most endangered groups in urban traffic. The EU-funded collaborative research project PROSPECT (‘PROactive Safety for PEdestrians and CyclisTs´) aims to significantly improve safety of those unprotected traffic participants by expanding the scope of scenarios covered by future active safety systems in passenger cars. Concepts for sensor control systems are built into three prototypes covering emergency interventions such as Autonomous Emergency Braking (AEB) as well as Autonomous Emergency Steering (AES). These systems tackle the well-known challenges of currently available systems including limited field-of-view by sensors, fuzzy path prediction, unreliable intent reaction times and slow reaction times. These highly innovative functions call for extensive validation methodologies based on already established consumer testing procedures. Since these functions are developed towards the prevention of intersection accidents in urban areas, a key aspect of the advanced testing methodology is the valid approximation of naturalistic trajectories using driving robots. Eventually, several simulator studies complemented a user acceptance and benefit analysis to evaluate the expected overall impact of the PROSPECT systems. The results achieved within the PROSPECT project are highly relevant for upcoming test protocols regarding the most critical situations with Vulnerable Road Users (VRU). With introducing the new methods in Euro NCAP (European New Car Assessment Programme) a significant increase in road safety is expected.
Test and assessment procedures for passive pedestrian protection of passenger cars are in place for many years within world-wide regulations as well as consumer test programmes. Nevertheless, recent accident investigations show a stagnation of pedestrian fatality numbers on European roads alongside increasing injury severities for older road users. The EU-funded SENIORS (Safety ENhancing Innovations for Older Road userS) project developed and evaluated a thorax injury prediction tool (TIPT) for later incorporation within test and assessment procedures. Accident data indicates an increasing portion of AIS2 and AIS3+ thoracic injuries of older pedestrians and cyclists which are currently not assessed in any test procedure for vulnerable road users. Therefore, SENIORS focused on the development of a test tool predicting the risk of rib fractures of vulnerable road users (VRU). While injury risk functions were reanalyzed, human body model (HBM) simulations against categorized generic vehicle frontends served as input for the definition of test setups and corresponding impact parameters. TIPT component tests against a generic frontend and an actual vehicle were used for the evaluation of the technical feasibility. The TIPT component tests shows the general feasibility of a test procedure for the assessment of thoracic injuries, with good repeatability and reproducibility of kinematics and results. Impact parameters such as the inclination angles of the thorax, angles of the velocity vector and impact speeds well replicate the parameters gained from the HBM simulations. The proposed markup and assessment scheme offers the possibility of a homogeneous evaluation of the protection potential of vehicle frontends while maintaining justifiable testing efforts. During evaluation testing, the proposed requirements were entirely met. The developed prototype of TIPT and launching system offer impact angles and speeds as suggested by HBM simulations. However, since thorax impacts during pedestrian accidents do not occur perpendicularly to the vehicle surface in most cases, the TIPT built-in linear potentiometers do not acquire the true resultant intrusions on the ribcage and thus, TIPT rib deflections do not reflect the actual human injury risk. However; for the impact forward to the bonnet leading edge, the TIPT seems applicable without further modifications. The test and assessment procedures using the TIPT offer for the first time the possibility of replicating the kinematics of a pedestrian thorax with a component test. The developed assessment scheme gives a first indication on how the risk for thoracic injuries could be implemented within the Euro NCAP Box 3 assessment. Future development of the TIPT may focus on implementing a rib cage that can deflect in all axes in a humanlike way.