Refine
Year of publication
Document Type
- Conference Proceeding (136)
- Article (34)
- Part of a Book (9)
- Working Paper (6)
- Book (2)
Language
- English (187) (remove)
Has Fulltext
- no (187) (remove)
Keywords
- Safety (57)
- Sicherheit (57)
- Bewertung (42)
- Evaluation (assessment) (41)
- Germany (39)
- Deutschland (38)
- Test method (36)
- Anfahrversuch (34)
- Impact test (veh) (34)
- Prüfverfahren (33)
Institute
This study aimed to better understand nitrate transport in the soil system in a part of the state of North Rhine-Westphalia, in Germany, and to aid in the development of groundwater protection plans. An advection-diffusion (AD) cell was used in a miscible displacement experiment setup to characterize nitrate transport in 12 different soil samples from the study area. The three nitrate sorption isotherms were tested to define the exact nitrate interaction with the soil matrix. Soils varied in their properties which in its turn explain the variations in nitrate transport rates. Soil texture and organic matter content showed to have the most important effect on nitrate recovery and retardation. The miscible displacement experiment indicated a decrease in retardation by increasing sand fraction, and an increase in retardation by increasing soil organic matter content. Soil samples with high sand fractions (up to 94 %) exhibited low nitrate sorption capacity of less than 10 %, while soils with high organic matter content showed higher sorption of about 30 %. Based on parameterization for nitrate transport equation, the pore water velocity for both sandy and loamy soils were significantly different (P < 0.001). Pore water velocity in sandy soil (about 4 x 10 high 3 m/s) was about 100 to 1000 larger than in loamy soils (8.7 x 10 high 5 m/s). On the other hand, the reduction in nitrate transport in soils associated with high organic matter was due to fine pore pathways clogged by fine organic colloids. It is expected that the existing micro-phobicity increased the nitrate recovery from 9 to 32 % resulting in maximum diffusion rates of about 3.5 x 10 high 5 m/s2 in sandy soils (sample number CS-04) and about 1.4 x 10 high 7 m/s2 in silt loam soils (sample number FS-02).
Intelligent transportation systems have a high potential to optimise traffic flow, to increase road traffic safety and to reduce environmental pollution. Real Time Traffic Information (RTTI) systems help to achieve these targets. Beside verbal radio announcements the most used RTTI service is the Traffic Message Channel (TMC) as a part of the Radio Data System (RDS). TMC messages support drivers in their choice of efficient routes or prepare them to cope with situations on the route ahead. The main focus of the paper is on the quality of TMC messages in Germany. After a brief overview of RTTI stakeholders in Germany and their role in the German public traffic information chain the following literature analysis summarizes the state-of-the-art on traffic information quality. Then the paper gives an overview about methodology and first results of an ongoing project on traffic information quality that has been initiated by the Bundesanstalt für Straßenwesen (BASt, German Federal Highway Research Institute) in 2008. The paper describes a concept how to check all processing iterations of the traffic information chain and occurring failures. A cause-effect-analysis forms the basis of this concept to get an idea which reasons (= process) lead to which measurable effect (= quality indicator). The paper demonstrates the principle with the pre-process of the Location Code List (LCL), which is the major basis for message coding since the LCL describes all locations that can be named in a TMC message.
Test and assessment procedures for passive pedestrian protection of passenger cars are in place for many years within world-wide regulations as well as consumer test programmes. Nevertheless, recent accident investigations show a stagnation of pedestrian fatality numbers on European roads alongside increasing injury severities for older road users. The EU-funded SENIORS (Safety ENhancing Innovations for Older Road userS) project developed and evaluated a thorax injury prediction tool (TIPT) for later incorporation within test and assessment procedures. Accident data indicates an increasing portion of AIS2 and AIS3+ thoracic injuries of older pedestrians and cyclists which are currently not assessed in any test procedure for vulnerable road users. Therefore, SENIORS focused on the development of a test tool predicting the risk of rib fractures of vulnerable road users (VRU). While injury risk functions were reanalyzed, human body model (HBM) simulations against categorized generic vehicle frontends served as input for the definition of test setups and corresponding impact parameters. TIPT component tests against a generic frontend and an actual vehicle were used for the evaluation of the technical feasibility. The TIPT component tests shows the general feasibility of a test procedure for the assessment of thoracic injuries, with good repeatability and reproducibility of kinematics and results. Impact parameters such as the inclination angles of the thorax, angles of the velocity vector and impact speeds well replicate the parameters gained from the HBM simulations. The proposed markup and assessment scheme offers the possibility of a homogeneous evaluation of the protection potential of vehicle frontends while maintaining justifiable testing efforts. During evaluation testing, the proposed requirements were entirely met. The developed prototype of TIPT and launching system offer impact angles and speeds as suggested by HBM simulations. However, since thorax impacts during pedestrian accidents do not occur perpendicularly to the vehicle surface in most cases, the TIPT built-in linear potentiometers do not acquire the true resultant intrusions on the ribcage and thus, TIPT rib deflections do not reflect the actual human injury risk. However; for the impact forward to the bonnet leading edge, the TIPT seems applicable without further modifications. The test and assessment procedures using the TIPT offer for the first time the possibility of replicating the kinematics of a pedestrian thorax with a component test. The developed assessment scheme gives a first indication on how the risk for thoracic injuries could be implemented within the Euro NCAP Box 3 assessment. Future development of the TIPT may focus on implementing a rib cage that can deflect in all axes in a humanlike way.
Per definition, SAE Level 2 (L2) Systems perform both the lateral and longitudinal vehicle motion control with the expectation that the driver completes the Object and Event Detection and Response (OEDR). Since every system performs also parts of the OEDR itself and this amount of OEDR also varies between different L2 systems depending on the intended system design, it cannot be taken for granted that drivers automatically understand their roles and responsibilities in interaction with the system. Especially highly reliable L2 systems performing a greater amount of OEDR while at the same time requiring only little driver input over time can make it difficult for drivers to correctly identify their role and responsibility. Until now, neither application-oriented assessment methods nor design guidelines for OEDR related system design features taking safety of human-machine-interaction into account are available. The objective is therefore to deliver a standardized tool for the assessment of human-machine-interaction-related safety of vehicles with L2 systems currently available on the market. To evaluate the impact of different system design aspects on safety of human-machine-interaction and also to be able to differentiate between system designs, a holistic, standardized and application-oriented assessment procedure is proposed. The novel tablet-based assessment tool focuses not only on available standards and guidelines but measures also concrete user behaviour and user understanding in interaction with the L2 systems. The aim is to gain further insights which cannot be measured directly by simple checklist instruments. For preparation, based on international standards, literature reviews and expert consultations, a first checklistbased expert-evaluation for currently available vehicles with L2 systems was developed. These assessments are focusing on different sources of user information (e.g. user manual), human-machine-interface design as well as the prevention of unintended use by different driver monitoring techniques. The checklist-tool was developed in cooperation with experts of different EuroNCAP test laboratories and validated in a common expert workshop to gain high level of standardization and agreement. However, to assess safety of human-machine-interaction holistically beyond these rather explicit forms of information design criteria, also implicit forms of drivervehicle-communication via vehicle dynamics, functional behavior or reliability play an important role and should be taken into account. Therefore, the main and novel methodological aim is to consider also interaction related processes regarding user´s understanding of roles and responsibilities when applying automated driving functions as well as user´s awareness of automation modes or traffic situations in the modular tablet-based assessment tool.
Airbags are, together with the three-point belt, the most effective passive safety equipment of vehicles. However, literature shows that sound pressure levels of up to 170 dB can occur during airbag deployment. A literature review revealed no systematic experimental data on possible hearing loss by airbag deployment, that also takes any other crash accompanied noise into account, such as deformation and impact noise. Also the rising number of airbags per vehicle resulting in a higher number of deployed airbags in an accident was not addressed with respect to hearing loss. Thus, an extensive test matrix of noise measurements during airbag deployments was conducted including onboard measuring during crashes and static measurements. Dynamic and static experiments with single and multiple airbag deployments were conducted. The results of this study show, that in the analyzed crash constellations the acoustic emission of the collision as well as the car deformation can trigger the stapedius reflex before the airbag deployment. The stapedius reflex protects the inner ear at least partially in case of dangerous sound levels. However, it seems that multiple airbag deployments in a short sequence pose a considerable risk for hearing impairments despite the fully contracted stapedius muscle. Further and in line with Price et al. (2013) it was found that the risk of hearing loss is lower with closed windows. The analysis of patient and accident data showed no link between airbag deployment and hearing loss. This might be caused by low case numbers of reported hearing loss problems up to now. In conclusion the results show that a singular analysis of the sound pressure of airbag deployments without crash accompanied noises is not sufficient as the protective effect of the stapedius reflex is neglected. Still, successive airbag deployments in a short timeframe raise the risk of hearing loss. Further investigation on hearing impairment due to airbag deployment and triggering of the stapedius reflex is needed and the data acquisition of accidents and patients should consider hearing loss aspects.
Bicyclists and pedestrians belong to the most endangered groups in urban traffic. The EU-funded collaborative research project PROSPECT (‘PROactive Safety for PEdestrians and CyclisTs´) aims to significantly improve safety of those unprotected traffic participants by expanding the scope of scenarios covered by future active safety systems in passenger cars. Concepts for sensor control systems are built into three prototypes covering emergency interventions such as Autonomous Emergency Braking (AEB) as well as Autonomous Emergency Steering (AES). These systems tackle the well-known challenges of currently available systems including limited field-of-view by sensors, fuzzy path prediction, unreliable intent reaction times and slow reaction times. These highly innovative functions call for extensive validation methodologies based on already established consumer testing procedures. Since these functions are developed towards the prevention of intersection accidents in urban areas, a key aspect of the advanced testing methodology is the valid approximation of naturalistic trajectories using driving robots. Eventually, several simulator studies complemented a user acceptance and benefit analysis to evaluate the expected overall impact of the PROSPECT systems. The results achieved within the PROSPECT project are highly relevant for upcoming test protocols regarding the most critical situations with Vulnerable Road Users (VRU). With introducing the new methods in Euro NCAP (European New Car Assessment Programme) a significant increase in road safety is expected.
To assess occupant safety in a crash test, criteria associating the measurements made with a crash test dummy to injury risk are necessary. To enable better protection of elderly car occupants the objective of this study was to develop improved thoracic injury criteria for the THOR average male dummy. The development of these criteria is usually based on matched dummy and Post Mortem Human Surrogate (PMHS) tests by relating the obtained PMHS injuries to dummy measurements. This approach is limited, since only a few tests in relevant loading conditions are available and any new test series requires high efforts to be performed due to their complexity and costs. To overcome these limitations and to extend the dataset for the development of THOR dummy chest injury risk functions a simulation-based approach was applied within the EC funded project SENIORS (Safety Enhanced Innovations For older Road Users - www.seniors-project.eu). Within this study frontal impact sled simulations with an FE model representing a THOR average male dummy and matched simulations with a human body model (HBM) representing an elderly car occupant were carried out. The HBM used for this study was the THUMS TUC with modified rib cage, which was developed in SENIORS. The modifications included material and geometry changes aiming to represent an elderly car occupant. The rib fracture risk was predicted with a deterministic approach whereby a rib was considered broken when the strain exceeded an age-dependent threshold. Furthermore, a probabilistic method was applied to predict the probability of sustaining a certain number of fractured ribs by comparing local strain values to the distribution of cortical rib ultimate strain. By relating the output from the HBM simulations to a multi-point dummy injury criterion, injury risk curves were calculated by statistical methods. The wide range of loading conditions resulted in the desired range of injuries and THOR ATD output. The number of fractured ribs predicted by the HBM based on the deterministic prediction method was between 0 and 15. Furthermore, the probabilistic risk for the number of rib fractures equal or greater than two, three or four was calculated for each load case. The THOR rib deflection criterion Rmax was between 18 and 56 mm, while the PC Score was in the range of 2.5 to 7.2. Based on these outputs new risk curves for the predicted deterministic (AIS2+/3+) and probabilistic injury risk were calculated. The new curves show reasonable shapes and significance that provide trust in their application. The new risk curves are compared to risk curves obtained by traditional methods. The results were found similar to previous injury risk functions based on physical tests, which gives a high level of confidence in the chosen approach. The simulation-based approach of matched ATD model vs. HBM simulation was successfully applied. Rmax curves show a slightly better quality than the injury criterion PC Score.
At the end of each year, the German Federal Highway Research Institute (BASt) publishes the road safety balance of the closing year. They describe the development of accident and casualty numbers disaggregated by road user types, age groups, type of road and the consequences of the accidents. However, at the time of publishing, these series are only available for the first eight or nine months of the year. To make the balance for the whole year, the last three or four months are forecasted. The objective of this study was to improve the accuracy of these forecasts through structural time-series models that include effects of meteorological conditions. The results show that, compared to the earlier heuristic approach, root mean squared errors are reduced by up to 55% and only two out of the 27 different data series yield a modest rise of prediction errors. With the exception of four data series, prediction accuracies also clearly improve incorporating meteorological data in the analysis. We conclude that our approach provides a valid alternative to provide input to policy makers in Germany.
Effects of time pressure on left-turn decisions of elderly drivers in a fixed-base driving simulator
(2019)
In countries with right lane traffic left-turn maneuvers at intersections are known to be particularly critical for elderly drivers. It has been suggested that the implementation and use of Advanced Driver Assistance Systems (ADAS) might offer a solution to compensate for age-related weaknesses in driving-related skills. In the present paper an experiment is reported which explored the effects of time pressure on the performance of left-turn manoeuvers supported by an ADAS function (time gap assistant). The study was performed in a fixed-base driving simulator with 20 younger (22-37) and 21 elderly drivers (60-84) who were observed when negotiating left-turn manoeuvers on rural roads with and without the assistance function active. Subjects performed the task once under conditions of time pressure once without. Results indicate that both age groups used the assistance function to perform the left-turn manoeuvers with shorter time gaps. Under conditions of time pressure this effect was more pronounced, and the effects of time pressure were stronger for the elderly. However, there were only weak indications for a specific benefit of the assistance function for the elderly.
Although cruise control (CC) is available for most cars, no studies have been found which examine how this automation system influences driving behaviour. However, a relatively large number of studies have examined adaptive cruise control (ACC) which compared to CC includes also a distance control. Besides positive effects with regard to a better compliance to speed limits, there are also indications of smaller distances to lead vehicles and slower responses in situations that require immediate braking. Similar effects can be expected for CC as this system takes over longitudinal control as well. To test this hypothesis, a simulator study was conducted at the German Aerospace Center. Twenty-two participants drove different routes (highway and motorway) under three different conditions (assisted by ACC, CC and manual driving without any system). Different driving scenarios were examined including a secondary task condition. On the one hand, both systems lead to lower maximum velocities and less speed limit violations. There was no indication that drivers shift more of their attention towards secondary tasks when driving with CC or ACC. However, there were delayed driver reactions in critical situations, e.g., in a narrow curve or a fog bank. These results give rise to some caution regarding the safety effects of these systems, especially if in the future their range of functionality (e.g., ACC Stop-and-Go) is further increased.