The following paper presents the nature and mechanism of injuries sustained in frontal impacts, focusing on car to car impacts. It was found that the body regions most frequently sustaining severe to fatal injuries were the legs and the thorax. The nature and mechanism of the injury sustained was investigated only for the thorax injuries, due to their potentially life threatening nature. The analysis revealed that the most frequent cause of the injury recorded was the seatbelt for low severity injuries and the front structure of the vehicle for higher severity injuries. An analysis of the effect of load limiter technology in the restraint system showed that the proportion of occupants who sustained "no thorax injury" did not increase when a load limiter was fitted to the restraint system. However, a decrease in the "organ" and "organ and skeletal" injuries was observed in the load limiter sample. Sample size and variation mean that these findings are not conclusive.
Motorcycle riders are one of the most vulnerable road users. Annually, on estimate 6000 people are killed in motorcycle accidents in the former 15 EU countries. The objective of this research was to investigate and analyze the main aspects and causes of this vulnerability and the accidents in general. For this aim around 70 accidents in The Netherlands were investigated in the framework of an international research program (MAIDS). Also a control group of motorcycles with riders was investigated so that exposure could be taken into account. An important result is that human failure is in 82% of the cases the main cause of the accident, in 52% this is due the other vehicle driver. Perception and decision failures are the most common failures. The most injuries are caused by the environment but they are typically only less severe (AIS1). Injuries caused by the car (front and side) are typically severe injuries (AIS4+). Previous convictions of the MC rider seem to be related to the chance to get involved in an accident. It was shown that the Dutch and the total MAIDS accident sample are comparable.
While many medical studies have dealt with the incidence, nature and treatment of polytrauma the injury-causing accident mechanisms are rarely discussed in detail, mostly due to the lack of documentation of the technical aspects. The present prospective study was started in late 2007 and collects data from traffic accidents with most severely injured in six south- German counties and two larger cities for the duration of one year. It is aimed at identifying and documenting all polytrauma cases (ISS ≥ 16) caused by traffic accidents and their crash circumstances. The data collection is based on an interdisciplinary concept to include both the police, emergency dispatch centers, hospitals and fire departments in the region and is completely anonymous. Potentially relevant cases where an emergency physician was called to the scene of a traffic accident are provided by the dispatch center. All three hospitals in the region suited for the treatment of polytraumatised patients record injuries, major diagnostic and surgery data. Data and images from the accident scene are provided by the police and by fire departments. The latter provide information which is usually not available from the police, like deployed airbags, vehicle extrication measures and detailed views of car interiors. The main objective of the study is to determine the structure of road users who sustain a polytrauma, their crash opponents and the injury patterns found in relation to the collision configuration and the protection by seat belts, air bags and other devices. With detailed documentation of vehicle damage and extrication measures the study is also intended to support the development of injury predictors for pre-hospital treatment and provide field data regarding further improvement of technical rescue.
A total survey of road traffic accidents involving most severely injured, defined as sustaining a polytrauma or severe monotrauma (ISS > 15) or being killed, was conducted over 14 months in a large study region in Germany. Data on injuries, pre-clinical and clinical care, crash circumstances and vehicle damage were obtained both prospectively and retrospectively from trauma centers, dispatch centers, police and fire departments. 149 patients with a polytrauma and eight with a severe monotrauma were recorded altogether. 22 patients died in hospital. Another 76 victims had deceased at the accident scene. In 2008, 49 % of patients treated with life-threatening injuries were car or van occupants, 21 % motorcyclists, 18 % cyclists and 10 % pedestrians. Among fatalities at the scene, vehicle occupants constituted an even larger portion. The number of road users with life-threatening trauma in the region was extrapolated to the German situation. It suggests that 10 % among the "seriously injured" as defined in national accident statistics are surviving accident victims with a polytrauma or severe monotrauma.
Pelvic fracture, cracking or breaking of a portion of the pelvis are extremely common injuries in the side impact collisions of motor vehicles. Due to both its shape and structural architecture, mechanics of the pelvic bone is complicated. There is a lack of knowledge regarding the dynamic behavior of the pelvis and its biomechanical tolerance under impact environment. Hence this study is aimed at the understanding of the mechanical response of the human pelvis with three-dimensional finite element (FE) models, under side impact load, applied through a structure, equivalent to a car door. The door structure was modeled, considering few layers, consisting of foam (Styrodur®, 3035 CS), plastic (UHMWPE), steel, glass and steel, putting them in series. A soft tissue layer (equivalent to fat) was also considered on the greater trochanter location. These FE models (with and without the car door structure) were analyzed with ANSYS-LS-DYNA-® dynamic finite element software to compare the effect of the car door padding system for shock absorption. It was observed that with proper combination of shock absorbing material (foam, etc.) and its thickness, the transmission of impact load to the body part (pelvis, etc.) from the outer surface of the car door could be reduced.
This paper reviews briefly the evolution of the investigation of transport accidents from the early beginnings when individual events were studied but systematic data was not collected. In the transport modes other than on the roads, accident investigation early on, even of single events, was important in introducing safety improvements. Road accidents, however, evolved enormously with the growth of car ownership without any comparable political response to the consequent deaths and injuries, equivalent to what happened with the other modes. From the 1950s data bases started to contribute to our knowledge of the epidemiology of road traffic injuries, and in-depth sample studies have contributed much to the body of knowledge in the last 30 years. However, even the basic input and output variables of a crash, its severity and the seriousness of the outcomes in terms of injuries and their consequences are not complete or agreed upon. Issues of experimental design and sampling are discussed. It is proposed that the most important area for current research to address is the effect of population variations on injury outcomes. The need for the establishment of good data bases for active safety issues is emphasised with the consequent need for better links between the research community and the police.
Verkehrspsychologische Nachschulungen stellen Maßnahmen zur Rehabilitierung von im Straßenverkehr auffälligen Kraftfahrerlnnen dar. Diese gesetzlich verankerten psychologischen lnterventionsprogramme werden mit hohem Aufwand konzipiert und sind bei der täglichen Durchführung mit beträchtlichen Kosten verbunden. Daraus ergibt sich die Notwendigkeit, die Effektivität der Nachschulungsmodelle durch eine wissenschaftliche Evaluation zu klären. Um die Effektivität der Nachschulungskurse der AAP (Austrian Applied Psychology) zu überprüfen wurde eine Fragebogenstudie mit Pre-Posttest-Designs durchgeführt. Die Ergebnisse der Alkoholkurse zeigen positive Auswirkungen hinsichtlich Einstellungsänderung, spezifischer Selbstwirksamkeitserwartung, interner Attributionen, Wissen und Gesamtbeurteilung.
Im Jahr 2005 wurde mit dem Bau der Niederrheinbrücke Wesel der Bau der Ortsumgehung Wesel begonnen. Der Beitrag berichtet über einige Ausführungsdetails der im Jahr 2009 fertiggestellten Baumaßnahme: die Herstellung des Pylons in hochfestem Beton, die Montage der Strombrücke, der Einsatz von Parallellitzenbündeln.
This study aimed at developing an injury estimation algorithm for AACN technologies for Germany and compared them to findings based on Japanese data. The data to build and to verify the algorithm was obtained from the German in-depth Accident Database (GIDAS) and split into a training and a validation dataset. Significant input variables and the generalized linear regression model to predict severe injuries (ISS>15) were selected to maximize area under the receiver operating characteristic curve (AUC). Probit regression with the input parameter multiple impact, delta v, seatbelt use and impact direction gave the largest AUC of 0.91. Sensitivity of the algorithm was validated at 90% and specificity at 76% for an injury risk threshold of 2%. It appears that no major differences between Japan and Germany exist for injury estimation based on delta v and impact direction. However, far side impact and multiple crash events appear to be associated with a larger risk increase in the German data.
Das Bundesministerium für Forschung und Technologie finanziert das Projekt "Leistra2", welches zum Ziel hat, den Reifen-Fahrbahn-Kontakt zu untersuchen und Maßnahmen zu entwickeln, die den Verkehrslärm reduzieren, insbesondere das Reifen-Fahrbahn-Geräusch. Das Projekt besteht aus drei Arbeitsgebieten: leise Reifen, leise Fahrbahnbeläge und die Verifizierung der Ergebnisse. Jedes Arbeitsgebiet gliedert sich in mehrere Unterprojekte. Dieser Vortrag gibt einen Überblick über Leistra2 und berichtet über neueste Tätigkeiten und Ergebnisse. Weitergehende Information und die Kontaktdaten der beteiligten Partner finden sich unter http:// www. LeiStra2. de . Das Programm ist Nachfolger des Programmes LeiStra (Leiser Straßenverkehr), welches ähnliche Themenschwerpunkte behandelte.
The German Federal Ministry of Economics and Technology is funding a projectrncalled "Leistra2" with the aim of understanding the tire road contact and to find measures to reduce traffic noise, in particular to reduce the noise of tires rolling on pavements, i.e. tire-road noise. The project is composed out of three mayor subjects, low noise tires, low noise pavements and verification of the results, each made out of single sub-projects. The purpose of this paper is to give a survey about Leistra2 and to report about the latest activities and results. More detailed information and contact data of the partners involved can be found at http://www. LeiStra2.de. The program is the successor of the program LeiStra (Leiser Strassenverkehr), dealing with similar topics.rn
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
Causation patterns and data collection blind spots for fatal intersection accidents in Norway
(2010)
Norwegian fatal intersection accidents from the years 2005-2007 were analysed to identify any causation patterns among their underlying contributing factors, and also to evaluate whether the data collection and documentation procedures used by the Norwegian in-depth investigation teams produces the information necessary to perform causation pattern analysis. A total of 28 fatal accidents were analysed. Details on crash contributing factors for each driver in each crash were first coded using the Driving Reliability and Error Analysis Method (DREAM), and then aggregated based on whether the driver was going straight or turning. Analysis results indicate that turning drivers to a large extent are faced with perception difficulties and unexpected behaviour from the primary conflict vehicle, while at the same time trying to negotiate a demanding traffic situation. Drivers going straight on the other hand have less perception difficulties. Instead, their main problem is that they largely expect turning drivers to yield. When this assumption is violated, they are either slow to react or do not react at all. Contributing factors often pointed to in literature, e.g. high speed, drugs and/or alcohol and inadequate driver training, played a role in 12 of 28 accidents. While this confirms their prevalence, it also indicates that most drivers end up in these situations due to combinations of less auspicious contributing factors. In terms of data collection and documentation, information on blunt end factors (those more distant in time/space, yet important for the development of events) was more limited than information on sharp end factors (those close in time/space to the crash). A possible explanation is that analysts may view some blunt end factors as event circumstances rather than contributing factors in themselves, and therefore do not report them. There was also an asymmetry in terms of reported obstructions to view due to signposts and vegetation. While frequently reported as contributing for turning drivers, they were rarely reported as contributing for their counterparts in the same accidents. This probably reflects an involuntary focus of the analyst on identifying contributing factors for the driver legally held liable, while less attention is paid to the driver judged not at fault. Since who to blame often is irrelevant from a countermeasure development point of view, this underlying investigator mindset needs addressing to avoid future bias in crash investigation reports.
Accident data shows that the vast majority of pedestrian accidents involve a passenger car. A refined method for estimating the potential effectiveness of a technology designed to support the car driver in mitigating or avoiding pedestrian accidents is presented. The basis of the benefit prediction method consists of accident scenario information for pedestrian-passenger car accidents from GIDAS, including vehicle and pedestrian velocities. These real world pedestrian accidents were first reconstructed and the system effectiveness was determined by comparing injury outcome with and without the functionality enabled for each accident. The predictions from Volvo Cars" general Benefit Estimation Model are refined by including the actual system algorithm and sensing models for a relevant car in the simulation environment. The feasibility of the method is proven by a case study on a authentic technology; the Auto Brake functionality in Collision Warning with Full Auto Brake and Pedestrian Detection (CWAB-PD). Assuming the system is adopted by all vehicles, the Case Study indicates a 24% reduction in pedestrian fatalities for crashes where the pedestrians were struck by the front of a passenger car.
Injury probability functions for pedestrians and bicyclists based on real-world accident data
(2017)
The paper is focusing on the modelling of injury severity probabilities, often called as Injury Risk Functions (IRF). These are mathematical functions describing the probability for a defined population and for possible explanatory factors (variables) to sustain a certain injury severity. Injury risk functions are becoming more and more important as basis for the assessment of automotive safety systems. They contribute to the understanding of injury mechanisms, (prospective) evaluation of safety systems and definition of protection criteria or are used within regulation and/or consumer ratings. In all cases, knowledge about the correlation between mechanical behavior and injury severity is needed. IRFs are often based on biomechanical data. This paper is focusing on the derivation of injury probability models from real world accident data of the GIDAS database (German In-depth Accident Study). In contrast to most academic terms there is no explicit term definition or definition of creation processes existing for injury probability models based on empirical data. Different approaches are existing for such kind of models in the field of accident research. There is a need for harmonization in terms of the used methods and data as well as the handling with the existing challenges. These are preparation of the dataset, model assumptions, censored/unknown data, evaluation of model accuracy, definition of dependent and independent variable, and others. In the presented study, several empirical, statistical and phenomenological approaches were analyzed regarding their advantages and disadvantages and also their applicability. Furthermore, the identification of appropriate prediction parameters for the injury severity of pedestrians has been considered. Due to its main effect on injuries of pedestrians and bicyclists, the importance of the secondary impact has also been analyzed. Finally, the model accuracy, evaluated by several criteria, is the rating factor that gives the quality and reliability for application of the resulting models. After the investigation and evaluation of statistical approaches one method was chosen and appropriate prediction variables were examined. Finally, all findings were summarized and injury risk functions for pedestrians in real world accidents were created. Additionally, the paper gives instructions for the interpretation and usage of such functions. The presented results include IRFs for several injury severity levels and age groups. The presented models are based on a high amount of real world accidents and describe very well the injury severity probability of pedestrians and bicyclists in frontal collisions with current vehicles. The functions can serve as basis for the evaluation of effectiveness of systems like Pedestrian-AEB or Bicycle-AEB.
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
The grip between the road surface and vehicle tires is the physical basis for the moving of all vehicles in road traffic. In case of an accident the available grip level is one of the most relevant influence factors, influencing the causation and the procedure of the accident. However, the estimation of the grip level is not easy and therefore, is commonly not done on the accident scene. This is especially true for the measurement of the water depth. Until now, real accident databases provide no measurement data about the grip level and the water film depth and thus, the estimation of its influence is not possible yet. From the tyre manufacturers point of view, it is important to know about the road conditions (namely grip level, macro-texture, water depth, temperature) at the accident scene, as well as the operating conditions of the vehicles (braking, loss of control, speed, etc). These data is necessary to define relevant tyre traction tests for the end-user and for regulations. For this reason VUFO and Michelin developed a consistent method for the measurements of grip level and water depth for the accidents of the GIDAS database. The accident research team of Dresden, which documents about 1000 accidents with at least one injured person every year, is measuring the micro-roughness and the macro-roughness directly on the spot. For the measurement of the micro-roughness a Skid Resistance Tester (British Pendulum) is used. The Mean Texture Depth (describing the macro-roughness) is measured by the Sand Depth Method. Since June 2009, measurements for more than 700 accidents including 1200 participants have been carried out. In case of wet or damp road conditions during the accident, the water depth is measured additionally. Therefore VUFO and Michelin developed a special measurement device, which allows measurements with an accuracy of 1/10 millimetre. The measurement point at the accident scene is clearly defined and thus, the results are comparable for all different accidents and participants. The use of the GIDAS database and the accident sampling plan allows representative statements for the German accident scenario. With this data it is possible for the first time to have an accurate view of the road conditions at the accident scene. One possibility is a more detailed estimation of hydroplaning accidents using the actually measured water depths. The development of new testing methods and new tires can be based on the real situation of the road infrastructure. Furthermore, the combination of the technical GIDAS data and the measured road surface properties can also be used for the estimation of effectiveness of several safety systems like the brake assist and/or emergency braking systems. The calculation of a reduced collision speed due to the use of a brake assist is only one example for the application of real measured grip level data.
Analysis of the accident scenario of powered two-wheelers on the basis of real-world accidents
(2013)
For the first time since 20 years the German national statistics of traffic accidents revealed an increasing number of fatalities and seriously injured persons in 2011. This negative development was especially caused by increasing numbers in all groups of vulnerable road users (VRU). Furthermore, the comparison of fatality reduction rates between several categories of road users shows that persons on motorcycles show the worst performance over years. Although every second fatality in German traffic accidents is still a car occupant, users of PTW make up more than 20% in the meantime. Assuming further improvements in the field of occupant protection this trend will continue. For that reason, a study on the basis of real-world accidents was conducted to describe the accident scenario involving motorcycles and to identify the reasons of the above-described fact. Approximately 1.800 motorcycle accidents out of GIDAS database were used for the analyses. The first part of the study deals with the question how representative the GIDAS database is for the German motorcycle accident scenario. Afterwards, detailed descriptive statistics on motorcycle accidents were presented considering numerous parameters about the accident scene, environmental influences, vehicle information, individual characteristics, interview data, injury severity and injury causation. One important point is the identification of the most frequent critical situations that are typical for motorcycle accidents. Furthermore, a special focus was on accident causation. Finally, conspicuous facts out of the analysis are emphasized. All in all, the study gives a comprehensive overview about the German motorcycle accident scenario. One the one hand, the use of weighted GIDAS data allows representative and robust statements on the basis of large case numbers; on the other hand highly detailed conclusions can be drawn. The results of the study help to understand the particularities of motorcycle accidents and provide approaches for further improvements in the field of PTW safety.
The paper presents a methodology for the benefit estimation of several secondary safety systems for pedestrians, using the exceptional data depth of GIDAS. A total of 667 frontal pedestrian accidents up to 40kph and more than 500 AIS2+ injuries have been considered. In addition to the severity, affected body region, exact impact point on the vehicle, and the causing part of every injury, the related Euro NCAP test zone was determined. One results of the study is a detailed impact distribution for AIS2+ injuries across the vehicle front. It can be stated, how often a test zone or vehicle part is hit by pedestrians in frontal accidents and which role the ground impact plays. Basing on that, different secondary safety measures can be evaluated by an injury shift method concerning their real world effectiveness. As an example, measures concerning the Euro NCAP pedestrian rating tests have been evaluated. It was analysed which Euro NCAP test zones are the most effective ones. In addition, real test results have been evaluated. Using the presented methodology, other secondary safety like the active bonnet (pop-up bonnet) or a pedestrian airbag measures can be evaluated.
The declining trend since 1991 in the number of killed people was broken in 2011 when overall 4 009 people died in traffic accidents in Germany. The question arises if there is a stagnating trend of fatalities in Germany in future? By breaking down the accidents with casualties towards a monthly view one can see a decreasing trend of fatalities in the warmer months especially since 2009. When comparing against winter months higher deviations are observed. In December 2011 an increase of 191 traffic deaths were registered (181 in 2010 compared to 372 in 2011). Further analyses of different accident influences were evaluated and their possibility of drastic change from one year to the other was determined. As seen weather- and environmental conditions are one of the major contributing factors and are one of the causes for the increased number of fatalities. To support the underlying assumption a model had been created to calculate the number of traffic deaths on a daily basis approach. As an input, road conditions projected through weather parameters and also different driving behaviors on weekdays or holidays were used. As a result, estimates of daily fatality with up to 75% precision can be achieved out of the 2009, 2010 and 2011 data. Further on it shows that weather and street conditions have a high influence on the overall resulting number of traffic accidents with casualties, and especially to the number of fatalities. Hence it is estimated that approximately 3 300 people were killed in traffic accidents in Germany in 2013 which would be again a reduction of another 13% compared to 2012. Therefore an answer to the question will be that the decreasing trend in traffic fatalities in Germany somehow is not broken when environmental conditions are included in national statistics. Their effects will become more visible in future accident statistics and it is estimated variances of 5% to 8% of the annual number of traffic fatalities in Germany will be seen.
The paper aims to study the injury risk and kinematics of pedestrians involved in different passenger vehicle collisions. Furthermore, the difference of pedestrian kinematics in the accidents involved minivan and sedan was analyzed. The 18 sample cases of passenger car to pedestrian collisions were selected from the database of In-depth Investigation of Vehicle Accident in Changsha of China (IVAC),of which the 12 pedestrian accidents involved in a minivan impact for each case, and the 6 accidents in a sedan impact for each. The selected cases were reconstructed by using mathematical models of pedestrians and accident vehicles in a multi-body dynamic code MADYMO environment. The logistic regression models of the risks for pedestrian AIS 3+ injuries and fatalities were developed in terms of vehicle impact speed by analyzing the minivan-pedestrian and sedan-pedestrian accidents. The difference of pedestrian kinematics was identified by comparing the results from reconstructed pedestrian accidents between the minivans and sedans collisions. The result shows that there is a significant correlation among the impact speed and the severity of pedestrian injuries. The minivan poses greater risk to pedestrian than sedan at the same impact speed. The kinematics of pedestrian was greatly influenced by vehicle front shape.
Topics of this report are: Road construction (highways, interstate roads, urban by-passes, cycle tracks, construction sites, level crossings removal), traffic management systems, road tunnel equipment, harmonisation of vehicle regulations, accident statistics and accident research, passive vehicle safety, active vehicle safety , automotive environmental protection and rescue systems.
Annually within the European Union, there are over 50,000 road accident fatalities and 2 million other casualties, of which the majority are either the occupants of cars or other road users in collision with a car. The European Commission now has competency for vehicle-based injury countermeasures through the Whole Vehicle Type Approval system. As a result, the Commission has recognised that casualty reduction strategies must be based on a full understanding of the real-world need under European conditions and that the effectiveness of vehicle countermeasures must be properly evaluated. The PENDANT study commenced in January 2003 in order to explore the possibility of developing a co-ordinated set of targeted, in-depth crash data resources to support European Union vehicle and road safety policy. Three main work activity areas (Work Packages) commenced to provide these resources. This paper describes some of the outcomes of Work Package 2 (WP2, In-depth Crash Investigations and Data Analysis). In WP2, some 1,100 investigations of crashes involving injured car occupants were conducted in eight EU countries to a common protocol based on that developed in the STAIRS programme. This paper describes the purposes, methodology and results of WP2. It is expected that the results will be used as a co-ordinated system to inform European vehicle safety policy in a systematic, integrated manner. Furthermore, the results of the data analyses will be exploited further to provide new directions to develop injury countermeasures and regulations.
Interaction of road environment, vehicle and human factors in the causation of pedestrian accidents
(2005)
The UK On-the-Spot project (OTS) completed over 1500 in-depth investigations of road accidents during 2000-2003 and is continuing for a further 3 years. Cases were sampled from two regions of England using rotating shifts to cover all days of the week and all hours of the day and night. Research teams were dispatched to accidents notified to police during the shifts; arrival time to the scene of the accident was generally less than 20 minutes. The methodology of OTS includes sophisticated systems for describing accident causation and the interaction of road, vehicle and human factors. The purpose of this paper is to describe and illustrate these systems by reference to pedestrian accidents. This type of analysis is intended to provide an insight into how and why pedestrian accidents occur in order to assist the development of effective road, vehicle and behavioural countermeasures.
Der Beitrag berichtet in einem ersten Teil über die in den Niederlanden angewendeten Inspektionstechniken zur Feststellung von Schäden (Rissen) bei orthotropen Stahlfahrbahnplatten und in einem zweiten Teil über die Instandsetzung der Moerdijkbruecke mit einer zusätzlichen Deckschicht aus bewehrtem hochfesten Stahlfaserbeton. Die Ausführungen zu den Inspektionstechniken umfassen die visuelle Inspektion, magnetische Inspektion, Farbeindringprüfung, Ultraschallprüfung und Diffraktionseffekt bei Anstrahlen von Fehlern (Time of Flight Diffraction (TOFD)) sowie radiographische Untersuchungen und das Wirbelstromverfahren. Für jede dieser Methoden wird ihre Wirkungsweise, Handhabung und der Anwendungsbereich angegeben. Die Moerdijkbrücke ist eine der meistbefahrenen Brücken in den Niederlanden mit einem erheblichen Schwerverkehrsaufkommen und weist etliche Schäden am Deckblech auf. Die bisher durchgeführte Instandsetzung durch Ausbessern der Längsschweissnähte führte nicht zum erhofften Erfolg. Der Bauherr entschloss sich daher, die Gussasphaltschicht durch einen bewehrten hochfesten Stahlfaserbeton mit einer Dicke von 5 cm mit Verbund zum Stahldeckblech zu ersetzen. Die Spannungen im Deckblech konnten auf diese Weise um einen Faktor 4 bis 5 reduziert werden. Die Methode reagiert jedoch empfindlich auf Abweichungen der Mischungsverhältnisse des Betons und der Viskosität.
In this study, we compared the injury severity of occupants according to the seating position and the crashing direction in motor vehicle accidents. In the driver's point of view, it was separated the seating position as "Near-side" and "Far-side". The study subjects were targeted by people who visited 4 regional emergency centers following motor vehicle accidents. Real-world investigation was performed by direct and indirect methods after patient- consent. The information of the damaged vehicle was informed by Collision Deformation Classification (CDC) code and the information of the injury of patients was informed by using the Abbreviated Injury Score (AIS) and Injury Severity Score (ISS). When the column 3 in CDC code was P, damaged at the middle part of lateral side, the average point of AIS 3 was 1.91-±1.72 in near-side and 1.02-±1.31 in far-side (p<0.01). The average point of maximum AIS (MAIS) was 2.78-±1.39 in near-side and 2.02-±1.11 in far-side (p<0.01). The average point of ISS was 15.74-±14.71 in near-side and 8.11-±8.39 in far-side (p<0.01). Also, when the column 3 in CDC code was D, damaged at the whole part of lateral side, it was significant that the average point of AIS 3 and MAIS in near-side was bigger than in far-side (p=0.02).
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Side impacts, both nearside and farside, have been indicated by research to be responsible for a large proportion of serious injuries from road crashes. This study aimed to compare and contrast the characteristics of nearside and farside crashes in Australia, Germany and the U.S., using the ANCIS, GIDAS and NASS/CDS in-depth-databases, in order to establish the impact and injury severity associated with these crashes, and the types of injuries sustained. The analyses revealed some interesting similarities, as well as differences, between both nearside and farside crashes, and the emergent trends between the three investigated countries. More specifically, it was indicated that whilst the severity of injury sustained in nearside crashes was slightly greater overall than that found for farside crashes, careful consideration of struck and nonstruck side occupants must be made when considering aspects such as vehicle design and occupant protection.
A change emerges in hospital landscape due to health political measures, which in consequence also influences the pre-clinical medical care of emergencies. The main focus of this study was to gather information about emergency medical care after traffic accidents on the basis of data of Bavarian emergency medical services. In Bavaria, in 2006 it was necessary to call an emergency doctor in the case of 14.261 traffic accidents. Predominantly the patients were provided by land-based life saving appliances, air rescue services were only applied in 19.1 % of the cases. 47.6 % of patients being involved in a traffic accident were transported into a primary health care hospital. A prehospital interval of more than 60 minutes was calculated in 20 % of emergency care. 96.2 % of the patients were transported to hospitals of tertiary or maximum supply by air rescue services. The life saving appliances" readiness for action is however restricted to daylight. A further limitation appeared for routine office hours in hospitals: Only 36.7 % of accidents occurred in this time frame. An increase of hospitalizations in clinics of maximum supply appeared from 2002 until 2006 while simultaneously the prehospital period was extended. To assure a sufficient medical care of seriously injured persons further on, a fulltime and area-wide expostulation of efficient facilities is necessary. For this purpose it is necessary to establish regional trauma networks as well as emergency medical service at night time. Beyond that, a cost efficient compensation of the structural, personnel and logistic expenses has to be assured.
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
Das Fehlen der Fahreignung stellt im Sinne der ICF eine Barriere bei der Teilhabe am Arbeitsleben dar. Die dargestellten Ergebnisse zeigen auf, dass weiterer Forschungsbedarf zum Thema Fahreignung und Therapie besteht, um den Patienten die Aussicht auf eine berufliche Reintegration zu bewahren. Durch ein effektives Training der Fähigkeiten zum Führen eines Kraftwagens könnten bei einem relevanten Anteil der Patienten die Voraussetzungen zur Teilhabe am Arbeitsleben stark verbessert werden. Durch die Präsentation dieser Ergebnisse kann eine Verbesserung des Problembewusstseins erwartet werden, da immer noch nicht alle Patienten über mögliche Einschränkungen der Fahreignung aufgeklärt werden. Daneben muss dem Fachpublikum die Notwendigkeit aufgezeigt werden, über neue Rehabilitationsstrategien zur Wiedererlangung beziehungsweise Verbesserung der Fahreignung nachzudenken.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
In recent years special attention has been paid to reducing the number of fatalities resulting from road traffic accidents. The ambitious target to cut in half the number of road users who are killed each year by 2010 compared with the 2001 figures, as set out in the European White Paper "European Transport Policy for 2010: Time to Decide" implies a general approach covering all kinds of road users. Much has been achieved, e.g. in relation to the safety of car passengers and pedestrians but PTW accidents still represent a significant proportion of fatal road accidents. More than 6,000 motorcyclists die annually on European roads which amounts to 16% of the EU-15 road fatalities. The European Commission therefore launched in 2004 a Sub- Project dealing with motorcycle accidents within an Integrated Project called APROSYS (Advanced PROtection SYStems) forming part of the 6th Framework Programme. In a first step, the combined national statistical data collections of Germany, Italy, the Netherlands and Spain were analysed. Amongst other things parameters like accident location, road conditions, road alignment and injury severity have been explored. The main focus of the analysis was on serious and fatal motorcycle accidents and the results showed similar trends in all four countries. From these results 7 accident scenarios were selected for further investigation via such in-depth databases as the DEKRA database, the GIDAS 2002 database, the COST 327 database and the Dutch element of the MAIDS database. Three tasks, namely the study of PTW collisions with passenger cars, PTW accidents involving road infrastructure features, and motorcyclist protective devices have been assessed and these will concentrate inter alia on accident causes, rider kinematics and injury patterns. A detailed literature review together with the findings of the in-depths database analysis is presented in the paper. Conclusions are drawn and the further stages of the project are highlighted.
Die aktuellen Richtlinien zur Bestimmung der Blutalkoholkonzentration (BAK) für forensische Zwecke (BAK-Richtlinie, 2007) lassen unter bestimmten Bedingungen auch zwei verschiedene gaschromatographische Analysen anstatt der häufig angewandten Kombination Gaschromatographie und enzymatische Methode ADH zur Bestimmung des Blutalkoholgehaltes zu. Untersucht wurde die Messpräzision zweier gaschromatographischer Verfahren bei der Alkoholanalytik im Vergleich zur häufiger angewandten Methodenkombination. In mehr als 50 Prozent der Fälle hat sich bei den verglichenen Methodenkombinationen ein identischer Mittelwert ergeben. Ansonsten waren die Abweichungen gering. Damit werden die hohen Anforderungen, die an die forensische Blutalkoholbestimmung gestellt werden, durch die modernen Laborautomaten erfüllt.
Um die Sicherheit der Straßentunnel zu gewährleisten, werden mehr als 400 m lange Tunnel ständig durch eine Tunnelleitzentrale überwacht. Die dort eingehende Flut von Einzelinformationen, wie Kamerabilder und zahlreiche Sensordaten, muss permanent durch das Personal erfasst und beurteilt werden. Das Projekt ESIMAS (Echtzeit-Sicherheits-Management-System für Straßentunnel) wird neue Wege aufzeigen, um die Leitstellenmitarbeiter zu unterstützen. Auf Grundlage der Datenanalyse und -bewertung von ESIMAS können zukünftig sicherheitsrelevante Ereignisse, wie ein Brand im Tunnel, zuverlässig und rechtzeitig erkannt werden. Im Ernstfall soll ESIMAS dem Leitzentralenpersonal sowie den Einsatz- und Rettungsdiensten Handlungsempfehlungen zur Ereignisbewältigung zur Verfügung stellen. Auf Basis dieser Handlungsempfehlungen können Maßnahmen schnellstmöglich und gezielt durchgeführt werden. Der innovative Ansatz von ESIMAS besteht in der ganzheitlichen Betrachtung aller Einzelinformationen und ihrer automatischen Auswertung und Bewertung. Hierdurch ist eine schnellere Reaktion der Leitstelle zum Schutz der Verkehrsteilnehmer möglich.
Betonfahrbahndecken werden seit vielen Jahrzehnten mit guten Gebrauchseigenschaften und langer Nutzungsdauer hergestellt. Um den wachsenden Anforderungen hinsichtlich der Verkehrssicherheit, der Umweltverträglichkeit und der Wirtschaftlichkeit gerecht werden zu können, ist eine stetige Weiterentwicklung erforderlich. Im September 2006 fand in Brüssel das 10. Internationale Betonstraßen Symposium statt. Im Rahmen umfangreicher Forschungsarbeiten und Studien auf Erprobungsstrecken wurden auf internationaler Ebene Untersuchungen zur Dauerhaftigkeit von Betonfahrbahnen durchgeführt. Der vorliegende Bericht stellt die Zusammenfassung von insgesamt 12 Fachbeiträgen aus 9 Nationen zum Themenblock "Kosteneffiziente und langlebige Straßen" dar.
In dem Beitrag präsentieren die Autoren einige laufende und geplante Forschungsvorhaben der Bundesanstalt für Straßenwesen (BASt), die wesentliche Bestandteile der Forschungslinie (FL) Q5 "Innovationen: Von der Idee in die Praxis" der mittelfristigen Forschungsplanung der BASt darstellen. Bei den konkreten Projekten geht es um die Entwicklung eines geeigneten Bewertungsverfahrens für Innovationen, um das Sichten neuer Forschungsideen aus denen neue Forschungsvorhaben resultieren können, um Nutzung von numerischen Methoden für die Entwicklung neuer Baustoffe und Bauweisen, sowie um den Aufbau einer geeigneten Untersuchungsinfrastruktur.
Die Straßenverkehrsinfrastruktur und der Straßenverkehr müssen sich künftig vielen Herausforderungen stellen. Zu nennen sind hier die Globalisierung, die Nachhaltigkeit, der Anstieg des Güterverkehrs und der technologische, demografische und klimatische Wandel. Die Straßenverkehrsinfrastruktur und der Straßenverkehr müssen sich den prognostizierten und projizierten Veränderungen anpassen. Die BASt betreut in ihrer Strategie "Anpassung der Straßenverkehrsinfrastruktur an den Klimawandel (AdSVIS)" bereits mehr als ein Dutzend Projekte. Diese Strategie soll dazu beitragen, die Verwundbarkeit gegenüber den Folgen des Klimawandels zu mindern bzw. eine leistungsfähige Straßenverkehrsinfrastruktur zu erhalten. Hierfür entscheidend sind nicht nur die durchschnittlichen Änderungen von klimatischen Parametern, sondern mehr noch das Auftreten von Extremwetterereignissen. Geringe Änderungen bei den Mittelwerten können sich aber in hohen Zunahmen bei der statistischen Verteilung der Extremwerte wie z. B. Hitzeperioden, Starkregen, Sturmböen äußern. Der zentrale Punkt der Anpassungsstrategie ist die Risikoanalyse wichtiger Güter- und Transitverkehrsachsen unter Einbeziehung von Seehäfen. Das Ziel dieses Projektes ist die Identifikation, Analyse und Bewertung der Risiken aus den projizierten Klimaänderungen für ausgewählte Streckenabschnitte im deutschen Teil des TEN-T (Transeuropäisches Netz Transport) in Anlehnung an die im ERA-NET ROAD Projekt RIMAROCC entwickelte Methodik. Hierfür werden für die relevanten meteorologischen Parameter Grenzwerte ermittelt, bei deren Überschreitung es für die Elemente der Straßenverkehrsinfrastruktur aus den Bereichen Erdbau, Entwässerung, Straßenbefestigungen, Ingenieurbau und Verkehrstechnik problematisch bzw. kritisch werden kann. Dabei werden nicht nur nach aktuellen Stand der Technik gefertigte Abschnitte des Straßennetzes betrachtet, sondern auch solche älterer Bauweisen und deren Vorkommen im Netz. Über die Fusion der Straßennetzdaten mit regionalisierten Klimaprojektionen werden schließlich die Lokalitäten mit prioritärem Anpassungsbedarf ermittelt. Anschließend werden für die identifizierten Risikobereiche erforderliche Anpassungsmaßnahmen entwickelt, erprobt und hinsichtlich ihrer Wirksamkeit bewertet. Da im Fokus die kostenintensiven Elemente der Straßenverkehrsinfrastruktur mit langer Nutzungsdauer wie Brücken und Straßengründungen stehen, müssen Anpassungsmaßnahmen bereits bei zeitnah anstehenden Erneuerungsarbeiten erfolgen, um die Folgenkosten der Klimaänderung zu senken. Das derzeit laufende Projekt "Risikoanalyse wichtiger Güter- und Transitverkehrsachsen unter Einbeziehung von Seehäfen" stellt eine erste Annäherung an den Aufbau eines Risikomanagements dar. Die hierbei verwendete RIMAROCC-Methodik muss dazu erweitert, weiterentwickelt und validiert werden. Erst dann kann die Risikoanalyse auf Netzebene durchgeführt und die erforderlichen Anpassungsprogramme aufgestellt werden.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.
Automotive Engineering, Mechanical Engineering and TechnologyrnAbstract: The degrees of injury severity, as a rule injuries scaled by AIS of specific regions of the human body, investigated out of road traffic accidents correspond to the body-specific loading values, which are found out with the aid of experimental or mathematical simulation of crash tests with motor vehicles or with sled tests. The coherence between the injured human being on the one hand and the physical and the theoretical model respectively on the other hand is established by the risk function, which describes the probability of degrees of injury severity in dependence on the protection criteria. Due to the different physical characteristics in the simulation, e.g. accelerations, forces, compressions and their velocity, the compilation of these quantities, comparable to the MAIS, the maximal occurred single AIS obtained in accident analysis is much more difficult in the simulation than in the accident occurrence. Therefore it is obvious to normalize the loading values gained out of simulation and to summarise them to an entire value in a suitable manner, the safety index.rn
One goal of the assessment of the crashworthiness of passenger cars is to characterize the potential of injury outcome to occupants of cars involved in an accident. This can be achieved by the help of an index that puts the number of injured occupants of passenger cars in relation to the number of cars involved in an accident. As a consequence, this index decreases with a lower potential of injury and rises with a higher number of injuries while assuming a fixed number of accidents. Another index is introduced that uses an economical weighting of each injury level. The consequential injury costs are calculated using the average economical costs for lightly, severely and fatally injured persons. The calculation of the safety indices is based on an anonymized sample of accident data provided by the Federal Statistical Office. An index of Mercedes passenger car drivers depending on the year of registration between 1991 and 2006 is compared to the index of drivers of cars of other makes within the same range of registration years.
This study aimed to identify the occurrence, type and mechanisms of the traumatic injuries of the vulnerable road users in vehicle collisions, and to determine the effects of human, engineering, and environment factors on traffic accidents and injuries. The pedestrian accident cases were collected in the years 2000 to 2005 from Changsha Wujing hospital China and Accident Research Unit at Medical University Hannover in Germany. A statistic analysis was carried out using the collected accident data. The results from analysis of Changsha data were compared with results from analysis of GIDAS data Hannover. The injury severities were determined using AIS code and ISS values. The results were presented in terms of cause of injuries, injury distributions, injury patterns, injury severity. The factors influenced the injury outcomes were proposed and discussed for the vehicle transport environment and road users. The results were discussed with regard to accident data collection, accident sampling and injury distributions etc. In the urban area of Changsha, motorcycles and passenger cars are most frequently involved in vehicle pedestrian accidents. Head and lower extremities injuries are the predominant types of pedestrian injuries. The pedestrian accidents were identified as vital issue in urban traffic safety and therefore a high priority should be given to this road user group in research of safe urban transportation. In Hannover area, cars are most frequently involved in traffic accidents, injured pedestrians are involved in road traffic of Germany in 13% of all causalities only in 2005 and have nearly the same number as motorcyclists, but the half of bicyclists.
Accident research 2.0: New methods for representative evaluation of integral safety in traffic
(2013)
BMW has developed a procedure for rating Advanced Driver Assistance Systems (ADAS) benefits that integrates two distinct tools. The tool "S.A.F.E.R." is designed to analyze the pre-crash phase. The aim of S.A.F.E.R. is to simulate all relevant processes in sufficient detail to obtain reproducible estimates of key indicators (effectiveness, false positives, etc.). The relevant processes include not only traffic and vehicle dynamics, but also environmental and most importantly human factors. Representative distributions of factors and parameters are obtained by taking the stochastic variation of all relevant parameters into account in the simulations. The second tool, known as "ICOS", has been designed to provide a high-resolution, high-fidelity description of crash phase dynamics. If one converts the outputs of stochastic simulation into inputs for crash dynamics, the result is a comprehensive description of exactly how a safety system can reduce injuries. Applications currently focus on high-fidelity simulation of individual crashes in order to enhance our understanding and optimization of connected safety systems. An integrated simulation process thus allows an exact prediction of the effectiveness in individual cases in terms of injury severity. The development and rating of integral safety need to reflect the true efficiency in the field. The integrated approach described here could provide a valid and reproducible basis for rating connected systems of active and passive safety. In particular, "virtual experiments" using a traffic-based approach and incorporating models of all relevant processes constitute an essential element of the approach.
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
The incidence and treatment of sternal fractures among traffic accidents are of increasing importance to ensure best possible outcomes. Analysis of technical indicators of the collision, preclinical and clinical data of patients with sterna fractures from 1985-2004 among 42,055 injured patients were assessed by an Accident Research Unit. Two time groups were categorized: 1985-1994 (A) vs. 1995-2004 (B). 267/42,055 patients (0.64%) suffered a sterna fracture. Regarding the vehicle type, the majority occurred after car accidents in 0.81% (251/31,183 pts), followed by 0.19% (5/2,633pts) driving motorbike, and 0.11% (4/3,258pts) driving a truck. 91% wore a safety belt. Only 13% of all passengers suffering a sternal fracture had an airbag on board (33/255 car/trucks), with an airbag malfunction in 18%. The steering column was deformed in 39%, the steering wheel in 36%. Cars in the recent years were significantly older (7.67-±5 years (B) vs. 5.88-±5 years (A), p=0.003). Cervical spine injuries are frequent (23% vs. 22%), followed by multiple rib fractures (14% vs. 12%) and lung injuries (12% vs. 11%). We found 9/146 (6%) and 3/121 patients (3%) with heart contusion among the 267 sternal fractures. MAIS was 2.56-±1.3 vs. 2.62-±1.3 (A vs. B, p=0.349). 18% of patients were polytraumatized, with 11.2% dying at the scene, 2.3% in the hospital. Sternal fractures occur most often in old cars to seat-belted drivers often without any airbag. Severe multiple rib fractures and lung contusion are concomitant injuries in more than 10% each indicating the severity of the crash. Over a twentyyear period, the injury severity encountered was not different with 18% polytrauma patients suffering sternal fractures.
The European Union has set a target to reduce all road fatalities (over 40,000) with 50% in 2010. This target percentage remained unchanged with the introduction of the ten new member states within the EU as by May 1st, 2004. According to Eurostat, 34% of all fatalities in 1998 in the, then, fifteen states of the European Union were the result of single vehicle collisions. This represents over 14,000 lives lost each year of which many can likely be saved through better roadside infrastructure design. The challenge for road safety professionals is to find methods and design strategies that help to reduce these casualties. Procedures for full-scale vehicle crash testing of guard rails were first published in the US in 1962. Present European regulation is mainly based on these procedures and later developments. Since then the vehicle fleet has changed considerably. Due to the complexity of the actual safety problem the numerical simulation approach offers a good opportunity to evaluate the different parameters involved in road safety, such as infrastructure properties, vehicle type, vehicle occupants and injuries. The ideal situation would be that simulation tools are coupled or integrated and all involved effects would be related. At the moment this is not the case yet, but initiatives are taken and a new virtual era has started. This paper offers a method looking at two components that encompass the driving environment: the car and the guardrail. As part of the EC-funded project, RISER (Roadside Infrastructure for Safer European Roads) a multi body simulation program study is carried out to determine sensitivities of some parameters in car to guardrail collisions and gives insides in performance of the car with passive safety equipment, the guardrail and the interaction of these objects with each other. By offering a set of methods that includes these two aspects and their intertwining relations, more confidence can be gained in actually reducing fatalities due to single vehicle collisions with, or due to, roadside furniture. Reducing the number of fatalities of single vehicle crashes would contribute greatly to the stated goal of reducing casualties altogether.
The practicability and feasibility of using alcohol ignition interlock devices has been discussed for more than 15 years in Germany. Thereby, judicial issues have been treated conversely. Consensus exists about the fact that the voluntary use of alcohol ignition interlocks is in all areas of possible use recommendable. Great reservation is shown concerning the operation of the devices for DUI (Driving Under Influence) offenders. Main doubts regard the missing legal base for application in such cases and potential circumvention attempts while the need of supportive psychological measures is unquestioned. In 2011, the Ministry of Transport, Building and Urban Affairs entered this topic in its newly released traffic safety programme as a matter of future research. Almost in parallel, the Federal Highway Research Institute (BASt) launched an alcohol ignition interlock project for DUI offenders. The study at hand aimed at developing a comprehensive programme concept for the use of alcohol ignition interlocks as additional measure to psychological rehabilitation for DUI offenders. Expert surveys serve as input for the establishment of a widely accepted innovative concept for nationwide implementation. By means of a pilot trial, the added value of using a combination of structural (alcohol interlock) and individual (psychological measure) intervention for DUI offenders to the existing countermeasure system should be studied. In addition, selection criteria for DUI offenders eligible for future programme participation should be defined. The majority of the experts evaluate the introduction of alcohol ignition interlocks as a good option to enhance traffic safety. The possibility of early psychological rehabilitation is emphasized in the process. Those who do not approve alcohol ignition interlock usage estimate the amount of offenders eligible for such programmes too small. The survey also revealed that legal regulations for issuing an alcohol interlock restricted licence to DUI offenders is missing. Hence, a possible amendment to the German Driving Licencing Regulation was developed within the project. Consultations with the Ministry of Transport, Building and Urban Affairs and the Ministry of Justice disclosed the need for a change of the road traffic law before an amendment to the existing regulations may be put into force. At least, the person responsible in the Ministry of Justice developed a proposal for the law section that needs revision. All in all, it became clear within the process of the project that a field trial in Germany is still a distant vision. Nevertheless, all institutions involved are motivated to deal with the matter further on in order to pave the way for a soon start of the pilot trial.
The use of alcohol interlocks for DUI offenders is widespread around the world. in North America and Australia alcohol interlocks are core elements in the countermeasure system against DUI recidivism. Based on a European experience exchange hosted by the Federal Highway Research Institute (BASt) in October 2013, key features of European alcohol interlock programmes are illustrated. In addition, key findings from international alcohol interlock research are presented. They point towards a need for an accompanying rehabilitative measure in order to achieve long-lasting behavioural changes in the offender. Data from the interlock recorder can be used as predictor for recidivism risk, but also as objective data to aid counselling. Finally, an example of an accompanying rehabilitative measure, which was specifically developed for interlock programmes within a BASt project, is given.
Im Oktober 2007 wurde die Rügenbrücke, eine der längsten Hochbrücken Europas, für den Verkehr freigegeben. Der Beitrag befasst sich mit den Erfahrungen, die bei Planung und Bau dieses bemerkenswerten Bauwerks gemacht wurden, insbesondere hinsichtlich der vielen bautechnischen Innovationen bei dem Schlüsselbauwerk des Brückenzuges, der 570 m langen Schrägseilbrücke über den Ziegelgraben. Eine der wesentlichen Erstanwendungen für Deutschland betraf die Ausführung der Schrägseile mit Litzenbündeln des Systems DYNA Grip der SUSPA DSI. Wegen des aus Gründen des Vogelschutzes erforderlichen Mindestdurchmessers der Seile von 12 cm waren vollverschlossene Seile aus ingenieurtechnischen und wirtschaftlichen Gründen benachteiligt, sodass sich der Bauherr für Seile aus Litzenbuendeln entschied. Die Schrägseilbrücke über den Ziegelgraben wird schon jetzt als modernes Wahrzeichen der Stadt Stralsund empfunden. Sie passt sich gestalterisch hervorragend in die Umgebung ein und beeinträchtigt auch nicht die zum Weltkulturerbe zählende Altstadt von Stralsund. Besonders besticht das Bauwerk durch seine Leichtigkeit und die Einpassung der Formen der Bauteile, zum Beispiel wegen der tropfenfoermigen Gestaltung des Pylons und der Pfeiler, in das maritime Umfeld. Da die verwendeten Schrägseil-Litzenbündel noch nicht allgemein bauaufsichtlich zugelassen sind, kam der Qualitätssicherung für die Seile in allen Stufen der Planung, Fertigung, Montage und Bauwerksprüfung eine herausragende Bedeutung zu. Der zugehörige Qualitätssicherungsplan wird im Bericht ausführlich mit den wesentlichen \"schrägseilspezifischen\" Maßnahmen beschrieben. Schwingungen und Ermüdungsbeanspruchungen der Seile durch Fahrverkehr und Wind liessen sich durch einen mehrstufigen, kontinuierlich verdichteten Planungsprozess unter Nutzung von Versuchsdaten und Messungen am Bauwerk wirkungsvoll beherrschen. Aus Sicht der Bauwerksprüfung bestanden anfänglich Bedenken wegen der Erreichbarkeit der bis in 80 m Höhe über dem Brückendeck gespannten Schrägseile und der nicht direkt zugänglichen Litzen innerhalb des Hüllrohres sowie der Verankerungen. Daher wurden alle verfügbaren Prüfverfahren für Schrägseile an der Rügenbrücke getestet. Daraus ergab sich eine Prüfmatrix aus Prüfverfahren, Prüfmittel und Prüfumfang für die gesamte Nutzungsdauer. Zusammenfassend wird festgestellt, dass bei der Ziegelgrabenbrücke Schrägseile aus Litzenbündeln eine den vollverschlossenen Seilen ebenbürtige Bauart darstellen.