Konferenzveröffentlichung
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (637) (entfernen)
Schlagworte
- Conference (386)
- Konferenz (382)
- Germany (212)
- Deutschland (209)
- Unfall (188)
- Accident (187)
- Safety (123)
- Sicherheit (122)
- Injury (117)
- Verletzung (117)
Institut
Die meisten der in Betracht kommenden Zwischenquerschnitte werden durch die derzeitigen Entwurfsrichtlinien nicht abgedeckt. Hinreichende Erkenntnisse über ihre Leistungsfähigkeit, die bei verschiedenen Belastungen erzielbaren Verkehrsqualitäten und vergleichende Angaben zum Sicherheitsniveau der Zwischenquerschnitte liegen nicht vor. Die Projektgruppe "Zwischenquerschnitte" der Bundesanstalt für Straßenwesen untersucht daher die Vor- und Nachteile der Zwischenquerschnitte mit dem Ziel, Einsatzbereiche für die verschiedenen Ausbildungsformen von Querschnitten zu entwickeln. Der Bericht gibt einen Überblick über bisherige Aktivitäten der Projektgruppe und stellt erste Zwischenergebnisse der Untersuchung vor. Bisherige Messungen zeigen, dass der besondere Vorteil der zwei- und dreiseitigen Zwischenquerschnitte in der Verbesserung der Überholsituation liegt. Für die Beurteilung vierstreifiger Zwischenquerschnitte kann bislang erst die Aussage gemacht werden, dass immer dann, wenn die Verkehrsbelastung tatsächlich einen Querschnitt mit 4 Fahrstreifen erforderlich macht, man die beiden Fahrrichtungen aus Gründen der Verkehrssicherheit baulich trennen sollte.
This study analyses no.39 cases in which n.41 motorcyclists were fatally injured, or 36% of total motorcycle fatalities in Northern Ireland between 2004 and 2010 (n.114). There were n.17 cases (43.6%) where the actions of another vehicle driver caused the collision, in thirteen of these cases the motorcycles had their lights switched on. The remaining n.22 collisions (56.4%) were due to the actions of the motorcyclist. In the approach to the collision scene, there were n.13 cases (31.7%) in which the approach was a right hand bend and in n.8 (19.5%) cases, the approach was a left hand bend. In the remaining n.18 (43.9%) cases, the approach was a straight road. Of the n.17 (41.4%) motorcycles that slid after falling, n.10 (24.4%) fell onto their right side and the remaining n.7 (17.1%) fell onto their left side. The information from this study identifies primary and contributory causes of motorcycle collisions.
The changed focus in vehicle safety technology from secondary to primary safety systems need to evolve new methods to investigate accidents, high critical, critical and normal driving situations. Current Naturalistic Driving Studies mostly use vehicles that are highly equipped with additional measuring devices, video cameras, recording technology, and sensors. These equipped fleets are very expensive regarding the setup and administration of the study. Due to the great rarity of crashes it is additionally necessary to have a high distribution and a homogeneous distribution of subject groups. At the end all these facts are leading to a very expensive study with a manageable number of data. Smartphones are becoming more and more popular not only for younger people. Contrary to traditional mobile phones they are mostly equipped with sensors for acceleration and yaw rates, GPS modules as well as cameras in high definition resolution. Additionally they have high-performance processors that enable the execution of CPU-intensive tools directly on the phone. The wide distribution of these smartphones enables researchers to get high numbers of users for such studies. The paper shows and demonstrates a software app for smartphones that is able to record different driving situations up to crashes. Therefore all relevant parameter from the sensors, camera and GPS device are saved for a given duration if the event was triggered. The complete configuration is independently adjustable to the relevant driver and all events were sent automatically to the research institute for a further process. Direct after the event, interviews with the driver can be done and important data regarding the event itself are documented. The presentation shows the methodology and gives a demonstration of the working progress as well as first results and examples of the current study. In the discussion the advantages of this method will be discussed and compared with the disadvantages. The paper shows an alternative method to investigate real accident and incident data. This method is thereby highly cost efficient and comparable with existing methods for benefit estimation.
The number of injured car occupants decreases constantly. Nevertheless, they account for nearly 50% of all fatalities and about 44% of all seriously injured persons in German traffic accidents. Further reductions of casualties require multiple efforts in all parts of traffic safety. In this paper a detailed analysis of the important pre-hospital rescue phase was done. The basis for future improvements is the knowledge about injury causation of car occupants in combination with other corresponding influence factors. For that reason more than 1.200 severe (AIS3+) injuries of frontal car occupants were analyzed. For the most relevant injuries of car occupants multivariate analysis models were created to predict the probability of these injuries in a real crash scenario. In addition to the collision severity different influence factors like impact direction, seat belt usage, age of the occupant, and gender were analyzed. Furthermore, the models were checked regarding the goodness of fit and all results all results were checked concerning their robustness. The prediction models were created on the basis of 5.000 car accidents. Afterwards, the models were validated using 4.000 different car accidents. The prediction of the probability of severe injuries could be used for different applications in the field of traffic safety. One possibility is the implementation of the models in a tool for the on-the-spot diagnosis. The background for the development of such applications is the fact, that there are only limited diagnostic possibilities available at the accident scene. Nevertheless, the rescue forces have to make essential decisions like the alerting of the necessary medical experts, appropriate treatment, the type of transportation and the choice of an adequate hospital. These decisions quite often decide between life and death or influence the long-term effects of injured persons. At this point, indications of expectable injuries could help enormously. To enable even persons with limited technical knowledge to use the tool, a procedure was developed that facilitates the assumption of the given crash severity. Another important possibility for the application of the prediction models is the use for the qualification of information sent by e-call systems.
Over the last decades the number of traffic accident fatalities on German roads decreased by 77% down to 4968 in the year 2007. This positive development is due to optimisations of vehicle safety, roads and infrastructure and medical rescue issues. Up to now mostly the optimisations of secondary safety measures lead to this effect on vehicle safety. Since some years more and more driver assistance systems are available and lead to a further reduction of all accidents. These new systems are often comfort systems and have not primarily been developed to increase vehicle safety. In contrast to secondary safety systems primary safety systems are able to mitigate and avoid accidents. So in the future it is important to estimate the benefit of these systems in reducing accident numbers as well. Current benefit estimation methods mostly focus on a single system only and not on the combination of systems. In this paper a new method for a multivariate benefit estimation based on real accident data is developed. The paper describes the basic method to estimate the benefit of primary and secondary safety systems in combination. With the presented method the benefit will not be overestimated as it would be by a simple addition of the benefits of single systems. The model will be validated by a multivariate prospective benefit estimation of different vehicle safety systems in comparison to single benefit estimations of the same systems. For this the German In-Depth Accident Database is used. The results show the importance to implement the interactions of safety systems in the estimation process and rate the overestimation by a simple addition of the single system benefits. The validation includes primary and secondary safety systems in combination. The validation is done using more than 3500 real accidents which were initiated by cars. This sample out of the GIDAS database is representative for the current accident situation in Germany. The paper shows the necessity of a multivariate estimation of the benefit for existing and future safety systems.
In the last years various new driver information and driver assistance systems made their way into modern vehicles and there are yet countless systems underway. However, expenses for both, the development and the construction of these systems are tremendous. Therefore the interest of evaluating systems keeps growing steadily, not only regarding the results of systems developed in the last years but also regarding system ideas. Only if at least a rough benefit estimation is given, the industry can decide which development should be supported. However, there is still a lack of transparency of possible and useful methods for these kinds of estimations. These were analyses and structured in this study.
The accident research project in Dresden was founded in July 1999. To date over 6.000 crash investigations have been undertaken. About 10.000 vehicles have been documented and over 13.000 participants have been debriefed. But there is much more than this scientific success. Because of the interdisciplinary character between the medical and technical focus, the project affords an important contribution for the education of the involved students. Over 200 students of different fields of study have got experiences not only for the occupational career. This lecture describes the additional effects of the accident research project regarding the education of the students, the capacity for teamwork and learning about dealing with accident casualties.
Because of actual developments and the continuous increase in the field of drive assistant systems, representative and detailed investigations of accident databases are necessary. This lecture describes the possibility to estimate the potential of primary and secondary safety measures by means of a computerized case by case analysis. Single primary or secondary safety measures as well as a combination of both are presented. The method is exemplarily shown for the primary safety measure "Brake Assist" in pedestrian accidents. Regarding accident prevention only the primary safety measure is determined.
Bei Schrägseilbrücken und Hängebrücken ist die Tragfähigkeit und die Betriebsfestigkeit der Seile von entscheidender Bedeutung. Da in Deutschland seit einigen Jahren wieder verstärkt Schrägseilbrücken gebaut werden, kommt den neueren Entwicklungen auf diesem Gebiet eine besondere Bedeutung zu. Diese neuen Entwicklungen werden im Bericht beschrieben. An erster Stelle steht dabei die Anwendung von Litzenbündeln (LBS) in Deutschland bei der fertiggestellten Ziegelgrabenbrücke im Brückenzug der Rügenbrücke und der im Bau befindlichen Niederrheinbrücke Wesel. Diese im Ausland schon seit vielen Jahrzehnten angewendete Bauart stieß in Deutschland bisher auf Bedenken, insbesondere wegen der Prüfbarkeit und des Korrosionsschutzes. Litzenbündel bestehen im Wesentlichen aus 7-drähtigen Spannstahllitzen und speziellen Verankerungsteilen. Auf der freien Länge des Seils sind die Litzen durch ein HDPE-Rohr gegen äussere Beschädigungen und Umwelteinflüsse geschützt. Da Seile aus Litzenbuendeln bisher nicht bauaufsichtlich geregelt sind, war eine Zustimmung im Einzelfall erforderlich. Die Prüfung der Seile bei den regelmäßig durchzuführenden Bauwerksprüfungen ist verbunden mit einem großen technischen Aufwand, hohen Kosten und Beeinträchtigungen des Verkehrs. Der Bericht geht ausführlich auf mögliche Methoden der Seilprüfung ein. Bei der Ziegelgrabenbrücke wurde die magnetinduktive Prüfung, die sich bei vollverschlossenen Seilen seit vielen Jahren bewährt hat, zum Feststellen von Schäden an den Seilen aus Litzenbündeln angewendet. Neue Entwicklungen bei vollverschlossenen Seilen betreffen insbesondere die Korrosionschutzsysteme und die Ausführung der Ankerköpfe. In beiden Bereichen beschreibt der Bericht die Neuerungen. Bei den Instandsetzungen der vollverschlossenen Seile werden angespochen: dauerhafte Seilspreizung zur Verbesserung der Zugänglichkeit bei der visuellen Prüfung, Seilaustausch am Beispiel der Rheinbrücke Düsseldorf-Flehe und die Instandsetzung des Korrosionschutzes mit verschiedenen Methoden. Wegen der neueren technischen Entwicklungen entsprechen die derzeit gültigen einschlägigen Regelwerke teilweise nicht mehr dem Stand der Technik. Sie müssen daher überarbeitet oder gänzlich neu erstellt werden.
Accident simulation and reconstruction for enhancing pedestrian safety: issues and challenges
(2015)
The enhancement of pedestrian safety represents a major challenge in traffic accidents. This study allows a better understanding of the issues in pedestrian protection. It highlights the potential of in-depth studies in identifying relevant crash parameters interfering in the pedestrian safety. A computational simulation tool was developed to reconstruct pedestrian real-world crashes. A sample of 100 in-depth accident cases was reconstructed from two sources: 40 crashes provided by IFSTTAR-LMA and 60 crashes from CASR. To exemplify the methodology, two accident cases from each database were illustrated. A description of the sample of crashes was presented including the travel and impact speed of the vehicle, the driver reaction, the pedestrian walking speed, the scene configuration with the eventual obstacles, etc. This detailed description is pointing to the major factors affecting the limits of pedestrian safety systems.
Zur Ergänzung der bestehenden Routineverfahren in der forensischen Blutalkoholanalytik wurde ein massenspektrometrisches Verfahren mit d6-Ethanol als internem Standard entwickelt. Ziel war die Anwendung eines beweissicheren Bestimmungsverfahrens, bei dem Ethanol über die Retentionszeit und Substanzeigenschaften identifiziert wird. Die Pilotstudie belegt, dass die forensische Blutalkoholbestimmung durch Anwendung eines gaschromatographischen und massenspektrometrischen Verfahrens mit Dampfraumanalyse routinemäßig möglich ist. Im Gegensatz zum GC- und ADH-Verfahren ist die massenspektrometrische Blutalkoholbestimmung beweissicher. Die Autoren empfehlen die Aufnahme in die Richtlinien zur Bestimmung der Blutalkoholkonzentration für forensische Zwecke. Die Arbeit wurde vom Bund gegen Alkohol und Drogen im Straßenverkehr e.V. (B.A.D.S.) unterstützt.
Cycling supports the independence and health of the aging population. However, elderly cyclists have an increased injury risk. The majority of injured cyclists is victim of a single-sided accident, an accident in which there is no other party involved. The aim of the project "Safe and Aware on the bicycle" is to develop guidelines for an advisory system that is useful in preventing single-sided accidents. This system is able to support the elderly cyclist; enabling the cyclist to timely adapt his cycling behaviour and improve cycling safety and comfort. For the development of such advisory system the causes of singles accidents and the wishes of the elderly cyclist must be known. First step to obtain this insight was a literature survey and an GIDAS research. Unfortunately accidentology research with GIDAS did not give the full understanding of the pre-crash situations and (especially the behaviour related) factors leading to the accident. The second step was consultation of elderly cyclist through a questionnaire (n=800), in-depth interviews (n=12) and focus group sessions (n=15). This offered complementary information and a much better understanding of the behavioural aspects. Results concern the behaviour in traffic and identify specific physical (i.e. problems looking backwards over the shoulder) and mental issues. Furthermore, the needs and wishes for support in specific cycling situations were identified. In conclusion; The GIDAS results together with the information obtained contacting the elderly cyclists enabled setting up requirements for an advisory system, which is useful in preventing single-sided accidents.
Novice drivers are at high risk for crash involvement. We performed an analysis of causations, injury patterns and distributions of novice drivers in cars and on motorcycles in road traffic as a basis for proper measurements. Method Data of accident and hospital records of novice drivers (licence < 2 years) were analysed focusing the following parameters: injury type, localisation and mechanism, Abbreviated Injury Scale (AIS), maximum AIS (MAIS), delta-v, collision speed and other technical parameters and have been compared to those of experienced drivers. In 18352 accidents in the area of Hannover (years1985"2004), 2602 novice drivers and 18214 experienced drivers were recorded having an accident. Novice car drivers were more often and severe injured than experienced and on motorcycles the experienced riders were at higher risk. Novice drivers of both groups sustained more often extremity injuries. 4.5 % novice car drivers were not restraint compared to 3.7 % of the experienced drivers and 6.1 % novice motorcycle drivers did not wear a proper helmet (versus 6.5 %). Severe injuries sustained at a rate of 20 % at collision speeds below 30 km/h and in 80% at collision speeds above 50 km/h. Novice car drivers drove significant older cars. The risk profile of novice drivers is similar to those of drivers older than 65 years. Structural protection and special lectures like skidding courses could be proper remedial action next to harder punishment of violations.
Description of road traffic related knee injuries in published investigations is very heterogeneous. The purpose of this study was to estimate the risk of knee injuries in real world car impacts in Germany focusing vulnerable road users (pedestrians, bicyclists and motorcyclists) and restrained car drivers. The accident research unit analyses technical and medical data collected shortly after the accident at scene. Two different periods (years 1985-1993 and 1995-2003) were compared focusing on knee injuries (Abbreviated Injury Scale (AISKnee) 2/3). In order to determine the influences type of collision, direction and speed as well as the injury pattern and different injury scores (AIS, MAIS, ISS) were examined. 1.794 pedestrians, 742 motorcyclists, 2.728 bicyclists and 1.116 car drivers were extracted. 2% had serious ligamentous or bony injuries in relation to all injured. The risk of injury is higher for twowheelers than for pedestrians, but knee injury severity is higher for the latter group. Overall the current knee injury risk is low and significant reduced comparing both time periods (27%, p<0,0001). Severe injuries (AISKnee 2/3) were below 1%). Improved aerodynamic design of car fronts reduced the risk for severe knee injuries significantly (p=0,0015). Highest risk of injury is for motorcycle followed by pedestrians, respectively. Knee protectors could prevent injuries by reducing local forces. The classically described dashboard injury was rarely identified. The overall injury risk for knee injuries in road traffic is lower than estimated and reduced comparing both periods. The aerodynamic shape of current cars compared to older types reduced the incidence and severity of knee injuries. Further modification and optimization of the interior and exterior design could be a proper measurement. Classic described injury mechanisms were rarely identified. It seems that the AIS is still underestimating extremity injuries and their long term results.
Es wird auf Grund einer Befragung untersucht, ob ein signifikanter Unterschied zwischen Fahranfängern, die die Prüfung nach weniger als 21 Fahrstunden, und solchen, die sie nach 21 und mehr Stunden bestanden haben, in Bezug auf Unfallneigung und Unfallhäufigkeit besteht. Es ergab sich, dass die kurz ausgebildeten im ersten Jahr eine Fahrleistung von durchschnittlich 12.362 Kilometer, die langausgebildeten von 7.750 Kilometer aufzuweisen hatten. Pro 1 Million Kilometer hatten die kurzausgebildeten 45,6, die langausgebildeten 73,2 Unfälle. Dem entsprach das Verhältnis von anderen Auffälligkeiten. Bei den Kurzausgebildeten ergaben sich keine Hinweise auf Defizite. Der Nutzen einer personenunabhängigen Mindestzahl von Fahrstunden ist zweifelhaft. Fahrschüler, die eine verhältnismäßig große Zahl von Fahrstunden benötigen, stellen die eigentliche Problemgruppe dar. Fahrschüler, die in der Fahrschule schnell lernen und bei der Prüfung erfolgreich sind, haben vergleichsweise gute Fahranfängerchancen.
Nachhaltigkeit im Brückenbau
(2011)
Nachhaltigkeit und Energieeffizienz sind wichtige baupolitische Ziele. Der Bund als Bauherr ist sich seiner Vorbildfunktion bewusst: Baumaßnahmen sollen sowohl ökologisch verträglich als auch ökonomisch akzeptabel und sozio-kulturell angemessen sein. Alle drei Bereiche betreffen auch die Straßeninfrastrukturen in unterschiedlich ausgeprägter Weise. Aus Sicht des Bauherrn geht es um die Sicherstellung der Mobilität durch ein umweltverträgliches, wirtschaftliches und qualitativ hochwertiges Straßennetz. Für die Baupraxis stellt sich die Aufgabe, in ganzheitlicher Hinsicht optimierte Lösungen bereitzustellen. Brückenbauwerke haben eine hohe symbolische Kraft und prägen Städte und Landschaften. Sie sind nicht nur für Ingenieure faszinierend, sondern stellen als bedeutender Bestandteil der Straßeninfrastruktur einen hohen gesellschaftlichen Wert dar. In der heutigen Vergabepraxis werden Entscheidungen über Baumaßnahmen maßgeblich durch die Diskussion über Erstellungs- und einmalige Investitionskosten beeinflusst. Grund dafür sind auch die begrenzten finanziellen Ressourcen; dies führt aber nicht zwangsweise zu nachhaltigen Lösungen. Damit Brückenbauwerke ökonomisch und ökologisch optimiert sowie funktional und sozio-kulturell angemessen erstellt werden können, sind weiterentwickelte Wertungskriterien erforderlich. Hier liegt aber auch eine Chance für die Bauwirtschaft, ihre Kompetenz auf dem Gebiet des Bauwesens auszuschöpfen und qualitätsvolles und kostengünstiges Bauen im Lebenszyklus zu verbinden. Neue Instrumente und Methoden sind gefragt, die derzeit auf Initiative des BMVBS entwickelt werden. Vor diesem Hintergrund befasst sich eine Arbeitsgruppe der Bundesanstalt für Straßenwesen unter Beteiligung von Experten aus Forschung und Baupraxis mit der Entwicklung und Bereitstellung von Verfahren der Nachhaltigkeitsbewertung für Bauwerke der Straßeninfrastruktur. Ganzheitliche Wertungskriterien werden derzeit in Pilotstudien getestet.
The Federal Highway Network of Germany represents considerable fixed assets. Construction and maintenance activities not only require a high budget, but also influence the traffic infrastructure and, thus, the economy and society as a whole. The present safety of the network has to be ensured under consideration of environmental aspects. At the same time the network owner has to make sure that the civil works are carried out in the most efficient way. Considering the fact that financial resources are restricted, the costs have to be spent in a way to obtain the greatest possible benefit. This task is supported by the application of a comprehensive Asset Management, which is subdivided into operational and controlling tasks respectively. The paper describes the current management procedures.
In future, additional and more detailed data are needed about the current conditions of bridges for preventive maintenance management. Monitoring procedures are not merely able to provide key performance indicators for a specific point in time, but also over a period. These KPIs must be selected in such a way as to permit substantiated statements about the present and future condition of bridges. For this reason, greater efforts must be made to define the significant KPIs for the various types of bridges, and show how these figures can be reliably determined. Both the COST Action TU1402, and TU1406 offer important approaches which, properly combined, can deliver substantial added value to the calculation and description of the condition of bridges in the interest of proactive maintenance management.
Germany's road infrastructure grew over centuries to become the arteries and lifelines of our society. The present safety of the infrastructure has to be ensured under consideration of environmental aspects. At the same time the owner has to make sure that the maintenance activities are carried out in the most efficient way. Considering the fact that financial resources are restricted, maintenance costs have to be spent in a way to obtain the greatest possible benefit. In the case of bridges, which are one of the most important parts of the road infrastructure in Germany, this task is supported by the application of a bridge management system (BMS). The existing German BMS contains assessment and optimization procedures on object and network level and is the basis for advancements to meet future demands. Developments concern life cycle and quality-oriented, holistically optimized procedures. Reasonable infrastructure management will contribute to meeting efficiency and sustainability objectives and to achieving interoperability. Here holistic network infrastructure management methods are required. There is a strong need for management solutions during the whole service life of a structure. The definition of criteria for evaluation of the relevance of failure mechanisms, including acceptance thresholds, requires the availability of relevant data for management procedure. Tools for innovative investigation methods and an effective data management will help in meeting the requirements. Relevant fields of research are improved maintenance strategies to meet future demands concerning heavy goods traffic, application and further development of nondestructive testing methods for efficient and sustainable management structures, and the improvement of analytic management tools to meet future demands.
Allein im Netz der Bundesfernstraßen sind etwa 35.000 Brücken mit einer Fläche von 25 Millionen Quadratmetern enthalten. Ihr Wiederbeschaffungswert beträgt etwa 70 Milliarden DM. Es wird über die notwendigen Aktivitäten zur Erhaltung dieser für die Aufrechterhaltung des auf den Bundesfernstraßen rollenden Verkehrs besonders wichtigen Bauwerke berichtet. Aufgrund des weiter stärker werdenden Verkehrs, der zunehmenden Fahrzeuggewichte sowie der wachsenden Anzahl von Schwertransporten unterliegen insbesondere die älteren Bauwerke größerer Beanspruchung, als man bei ihrer Planung in Rechnung stellen musste. Hinzu kommt die natürliche Alterung aus sonstigen äußeren Einflüssen wie Temperatur, Witterung und erhöhter Umweltbelastung. Die Verwendung von Auftausalzen führt insbesondere bei älteren Brückenüberbauten zu Korrosionsschäden an der Bewehrung des Betons. Durch die Entwicklung eines Bauwerks-Management-Systems (BMS) wird die Verbesserung der Erhaltung von Brücken und sonstigen Ingenieurbauten angestrebt. Der Aufbau und die Wirkungsweise des BMS werden dargelegt. Des Weiteren werden die schon seit langem eingeführten Prüfvorschriften für Bauwerke im Zuge von Straßen und Wegen (DIN 1076) sowie gängige Prüfverfahren beschrieben.
Brückenmanagement
(2001)
Die systematische Erhaltung der Brücken im Zuge der Bundesfernstraßen ist eine wichtige Aufgabe für den Baulastträger Bund und die Straßenbauverwaltungen der Länder. Um künftig Erhaltungsprogramme auf einer einheitlichen Grundlage unter Berücksichtigung gesamtwirtschaftlicher Grundsätze aufstellen zu können, wird durch die Bundesanstalt für Straßenwesen derzeit im Auftrag des Bundesministeriums für Verkehr, Bau- und Wohnungswesen ein umfassendes Bauwerks-Management-System (BMS) konzipiert und realisiert. Das geplante BMS beinhaltet alle Funktionen zur Durchführung des Erhaltungsmanagements. Grundlage ist die Erhebung und Bereitstellung von objektbezogenen Informationen. In Verbindung mit netzbezogenen Daten, Rahmenbedingungen und Restriktionen wird damit die Basis für Analyseprozesse, zum Beispiel Wirtschaftlichkeitsuntersuchungen, Priorisierungen und Bedarfsermittlungen bereitgestellt. Als Ergebnis werden Maßnahmenvorschläge, optimierte Programmplanungen und Angaben zum Finanzbedarf entwickelt. Verfahren und Programmsysteme werden schrittweise ab 2002 bis 2005 den Straßenbauverwaltungen zur Verfügung gestellt.
BMS-Entwicklungen
(2002)
BMS-Entwicklungen
(2003)
Im von der DG Home (CIPS Program) geförderten Projekt "SecMan " Security Manual for Road Infrastructures" wurde ein vierstufiges Verfahren zur Identifikation kritischer Straßeninfrastrukturen, ihre Bewertung hinsichtlich diverser von Menschen verursachter Gefahren sowie die Bestimmung effektiver Schutzmaßnahmen entwickelt. Diese Ergebnisse wurden in einem ganzheitlichen "best-practice" Handbuch zusammen getragen, welches einen trans-nationalen Sicherheitsmanagement-Ansatz für Betreiber und Eigentümer von Straßeninfrastrukturen in Europa ermöglicht. Im Folgenden wird die entwickelte Methodik vorgestellt, ausgehend von der Bewertung der Netzkritikalität über die Attraktivität und Vulnerabilität eines Bauwerks hin zu einer Bewertungsmethodik für die Auswahl geeigneter Schutzmaßnahmen.
The European CASPER (Child Advanced Safety Project for European Roads) project studying car child safety includes a sociological approach in order to have a better understanding of the behaviour of parents driving children under 12 years old. A questionnaire was distributed via the internet in Europe with 998 parents (representing 1638 children) from 22 European countries responding. The results inform on the way parents secure their children during a car trip. Many parents did not control how their children were installed in the child restraint system (CRS). A toddler was more likely to travel into a child seat than an older child was. Regarding misuse situations, an important part of the participants did not think that they could make mistakes when fixing the child seat to the car (26%) or when placing the child into the seat (39%). This leaves an important field of action especially by communication via different media and in the CRS sale outlets.
Rollover scenarios in Europe
(2005)
Rollover accidents seem to be a rising problem in Europe and therefore the systematic of this accident scenario should be investigated. Based on statistical investigations on major European accident databases for different countries a series of 73 real world rollover accidents was analysed. These cases were reconstructed using PC-Crash and preliminary categorised using a modified USbased rollover classification. In a first step, the rollover events were reconstructed from the point of conflict to the vehicle- rest position. The vehicles kinematics as well as its linear and rotational velocities were derived. In a second step typical velocity characteristics as well as kinematics were identified and the events categorised according to these criteria. Based on these results four main categories were defined, covering all reconstructed accidents. This categorisation was based on mechanical parameters (rotatory and translator kinematical data of the vehicle). Significant differences can be seen for different scenarios for the "first phase of rollover".
Interdisciplinary accident research and research projects of AARU Audi Accident Research Unit
(2017)
AARU (Audi Accident Research Unit) is an interdisciplinary research project of the University Hospital Regensburg in cooperation with AUDI AG. Specific objective is to comprehend the respective accident scenario and retrieve generally applicable findings as to technical, medical and psychological processes. In order to prevent traffic accidents and to alleviate vehicle accident consequences, postulates of general traffic safety, human-machine interaction, technical design and function of new vehicles and occupant as well as third party protection shall be inferred from these findings. Specifically, each accident with new Audi, Lamborghini and Ducati vehicles involved is analyzed interdisciplinary, discussed in a case meeting and anonymously documented with more than 2,000 parameters. The database is continually used for solving safety relevant issues. Parallel to accident analysis, research projects are performed in the fields medicine, psychology and engineering in order to gain comprehensive insight and identify potential additional areas of activity of accident research.
Die hier berichtete Auswertung der Leistungen in den Tests zur Messung kognitiv-psychomotorischer Fähigkeiten haben durchgehend erbracht, dass die neuroleptisch behandelten Patienten unter Stress und Zeitdruck in ihrem Leistungsumfang gegenüber Gesunden beeinträchtigt sind. Sie haben allerdings eine ausgeprägte Tendenz Fehler zu vermeiden, was sich - relativ gesehen - günstig auf die Qualität der Leistung auswirkt. Es bleibt derzeit offen, ob die Patienten ihre eigenen Leistungseinbußen in Teilbereichen durchaus empfinden und daraus kompensatorisch risikovermeidend reagieren. Wieweit die von den Patienten erbrachten Leistungen ausreichen, die Fahrtüchtigkeit daraus abzuleiten, kann hier generell nicht beurteilt werden. Es ist notwendig, Normwerte eines gerade noch zulässigen Mindestmaßes an psychomotorischer Funktionstüchtigkeit zu erarbeiten. Die weitere Auswertung der Befindlichkeitsbeurteilungen sowie der habituellen Persönlichkeitsmerkmale - als intervenierende Variable - wird möglicherweise mehr Licht in die Interpretation bringen.
The data situation for quantifying the proportion of accidents avoided by the introduction of active safety systems is incomplete, since there is generally no data available on the accidents avoided by the technology in question. In this paper, a split-register approach is suggested and compared with the classical case-control approach known from epidemiologic applications. Provided a set of assumptions hold, which can reasonably be made in such data situations, the split register approach allows inferences on the population accident risk. For both approaches the benefits of basing the analysis on the results of a logistic regression to adjust for confounding factors are outlined. The biasing effects of violating key assumptions are discussed and the split-register approach is demonstrated using the example of the active safety system ESP with data from the German in-depth accident study GIDAS.
This study that was funded by the Research Association for Automotive Technology (FAT) develops a method for the evaluation of the placement of tanks or batteries by using the deformation frequencies in real-world accidents. Therefore, the deformations of more than 20.000 passenger cars in the GIDAS database are analysed. For each vehicle a contour of deformation is calculated and the deformed areas of the vehicles are transferred in a rangy matrix of deformation. Thereby, the vehicle is divided into more than 190.000 cells. Afterwards, all single matrices of deformation are summarized for each cell which allows representative analyses of the deformation frequencies of accidents with passenger cars in Germany. On the basis of these deformation frequencies it is possible to determine least deformed areas of all passenger cars. Furthermore, intended placements of tanks or batteries can be estimated in an early stage of development. Therefore, all vehicles with deformations in the intended tank areas can be analysed individually. Considering numerous parameters out of the GIDAS database (e.g. collision speed, kind of accident, overlap, collision partner etc.) the occurring forces can be calculated or the deformation frequency can be estimated. Furthermore, it is possible to consider the influence of primary and secondary safety systems on the deformation behaviour. The analysis of "worst case accident events" is an additional application of the calculated matrix of deformation frequency.
Im Mittelpunkt der Überlegungen zu Perspektiven einer zeitgemäßen und sicherheitswirksamen Fahranfängervorbereitung steht die Absenkung des weiterhin hohen Anfangsrisikos bei Fahranfängern. Ausgehend von den positiven Erfahrungen mit dem Begleiteten Fahren ab 17 beauftragte das Bundesministerium für Verkehr, Bau und Stadtentwicklung (BMVBS) die Bundesanstalt für Straßenwesen (BASt) mit der Erarbeitung eines Rahmenkonzepts, in dem Entwicklungsperspektiven für weitere Verbesserungen der Vorbereitung von Fahranfängern und wissenschaftlich begründete Maßnahmenvorschläge für die Erhöhung der Fahranfängersicherheit formuliert werden. Zunächst werden die Aufgaben und die Vorgehensweise der Rahmenkonzepterarbeitung sowie die Kriterien für die Ableitung von Maßnahmenprioritäten skizziert. Ausgehend von den Erkenntnissen zur Entwicklung des Unfallrisikos im Verlauf der Fahrkarriere werden im Anschluss die maßgeblichen Ansatzpunkte zur verbesserten Gestaltung eines sicheren Übergangs in die Automobilität aufgezeigt. Zentrale Maßnahmenvorschläge des Rahmenkonzepts werden vorgestellt. Diese beziehen sich auf die Bekämpfung der maßgeblichen Ursachen des erhöhten Fahranfängerrisikos (Fahrerfahrungsdefizit und Einstellungsmängel), die Optimierung bestehender Fahranfängermaßnahmen und die verstärkte Erschließung von Technik und Wissenschaft für das Fahren lernen.
Seit einigen Jahren steht mit dem pupillographischen Schläfrigkeitstest (PST) ein objektives Messverfahren zur Ermittlung der Tagesschläfrigkeit zur Verfügung, wobei die Zunahme der spontanen Schwankungen des Pupillendurchmessers unter Müdigkeit registriert wird. Es wurde eingesetzt bei verschiedenen Probandengruppen, die einem potenziell erhöhten Risiko von Vigilanzminderungen ausgesetzt sind: chronische Schmerzpatienten (n = 20) beziehungsweise substituierte Heroinabhängige (n = 52) unter Opioiden, ambulante Patienten unter Psychopharmaka (n = 32), Allergiker unter Antihistaminika (n = 40) und medizinisches Nachtdienst-Pflegepersonal (n = 40). Verglichen wurde unter anderem mit zwei Kontrollgruppen (n = 21, n = 10). Bei den Untersuchungen ergaben sich relativ normale Schläfrigkeitswerte bei ambulanten Psychopharmaka-Patienten und Allergikern. Teils exzessiv erhöhte Werte wurden dagegen insbesondere bei substituierten Heroinabhängigen (81 Prozent), opiatversorgten Schmerzpatienten (59 Prozent) und dem Nachtdienstpersonal (70 Prozent) festgestellt.
At IAM RoadSmart we share the excitement about autonomous cars " who wouldn't! However over half of the drivers we polled supported concentrating on making drivers safer " among IAM RoadSmart members it was 70%. Driverless cars are still years away but delivering safer drivers can help reduce death and injury from tomorrow. Governments, academics and car makers need to work hard to convince sceptical British and American drivers that autonomous cars can deliver the benefits promised such as a 90% plus reduction in road deaths.
The Swedish "Vision Zero" regards road fatalities and severe injuries as unacceptable. The vision is based on this ethical perspective together with a fundament of shared responsibility between the system designers and the road user. The design of the traffic system shall protect the road user from these effects as long as he or she follows the traffic rules. It should be possible to make a mistake without being killed. This policy has, during the first period of the "vision zero" (since 1997) put high priority on road and car design where the purpose has been to develop a forgiving environment. Gradually it has, however, become clear that much more effort has to be focused on the responsibility of the road user. Protecting measures will have limited effect as long as the understanding and acceptance from road users is limited. During the last years, Sweden has gone through several improvements of the driver education and is in the middle of important improvements of road safety education for children in schools. Several EU-projects has contributed to this development. One aspect that has received large international interest is the lay instructed driver training from 16 years of age supervised by parents. This has been in use since 1993. Another is the development of mandatory courses, such as an introduction for the learner and the lay instructor, a "risk awareness" courses dealing specifically with speeding, seat belt use, drunk driving, tiredness, and driving on low friction. The presentation will share some of the "vision zero" fundaments together with the latest experiences, research and development concerning driver education in Sweden.
An der Fortbildungsakademie der Ärztekammer Nordrhein werden in einem 16-Stunden-Kurs Qualifizierungen zum Fachgutachter/zur Fachgutachterin für verkehrsmedizinische Begutachtung in Kooperation mit unterschiedlichen Fachreferenten aus den verschiedenen klinischen Bereichen durchgeführt. Leistungskontrollen zum Kursinhalt, ein intensives Arbeiten an Fallbeispielen oder gar eine fachliche Begleitung der ersten Gutachten sind nicht generell vorgegeben, wenngleich in Evaluationen zum Kurs insbesondere eine fallorientierte Ausbildung und eine Supervision zumindest in ersten eigenen Begutachtungen von den Teilnehmern/Teilnehmerinnen gewünscht werden. Auf der Grundlage der Erfahrungen der Autoren mit der Leitung/Moderation der entsprechenden Fachfortbildungen der Ärztekammer Nordrhein wurden das bestehende Curriculum kritisch diskutiert und Anregungen zur Umstrukturierung erarbeitet, die im Einzelnen vorgestellt werden. Dabei handelt es sich um ein Konzept auf der Basis des "blended learning": Via Internet wird vertiefendes Lehrmaterial für die verschiedenen Fachbereiche der medizinischen Begutachtung unter verkehrsmedizinischen Fragestellungen zur Bearbeitung angeboten. Die Bearbeitung selbst kann online kontrolliert und bei Bedarf auch mit Lerninhaltsüberpruefungen verknüpft werden. Zusätzlich können Fallbeispiele anonymisiert vorgelegt und mit tatsächlich ausgesprochenen Begutachtungen bereitgestellt werden. Weiterhin wird eine qualifizierte Begleitung zumindest zu Beginn der Gutachtertätigkeit angeregt.
Structured road markings are becoming popular as edge line on high speed roads, ensuring night time visibility (retroreflection) during rain. These markings are often also "audio-tactile": vehicles (un)intentionally driving over it may produce much more tyre/road sound, which may be observed in the vehicle but also in the vicinity. The sound increase inside the car can be considered as a positive side effect, as it alarms the driver and may be very helpful for the prevention of "doze off" traffic accidents. The sound increase perceived outside the car however, may have a positive aspect as it can warn people on the emergency lane about the approaching vehicle, but it may as well annoy people living around. A method for the assessment of the acoustic properties of audio-tactile markings has been developed. It is mainly based on the "Close Proximity" (CPX) method, an ISO method intended for the acoustic assessment of pavements. The results of measurement campaigns with CPX trailers in Belgium and Germany according to a specially designed procedure are presented. The feasibility of the method is discussed. The research has been carried out in the frame of the standardization activities of the CEN working group CEN/TC226/WG2 "Horizontal signalization".
India is one of the leading countries reporting highest road accidents & related injuries. TMARG (Tata Motors Accident Research Group) has been recording crashes in association with M/s. Lokamanya Medical Foundation since 2011 with M/s, Amandeep Hospitals since Aug 2013. This study has highlighted some accident types not discussed extensively in literature. Trucks to Truck impacts " Cabin interaction with overhanging loadbody structures and Offset underside impacts for passenger vehicles are seen in significant numbers. The paper discusses these in more detail including severity.
The development of tyre- and truck-manufacturers leads to the direction to introduce wide base single tyres (size 495/45R22,5) instead of twin tyres on the driving axle of trucks, tractors and busses. To study the driving behaviour and safety of various trucks and units with different tyre combinations and loading conditions was the aim of the study. A computer-aided simulation was used for this investigation. Drive tests with a 40 t unit with prototype single tyres on the drive axle were carried out to verify the simulation. Alterations in driving behaviour and driving safety are mainly dependent on the tyre cornering stiffness. The prototype wide single tyres had a higher lateral stiffness which leads to a higher degree of under-steering (safer driving behaviour). The altered spring base on the drive axle had no influence on the side- tilt stability of vehicle combinations but the solo truck profited from the higher rear axle roll stiffness (less danger for roll-over accidents). As far as the driving safety is concerned nothing speaks against wide base tyres on the drive axle. The simulation of a tyre defect in a bend (assuming 40% of the max. transferable side force for the flat tyre) showed no increased danger using wide single tyres. Later driving tests showed however the need of tyre run flat possibilities to avoid jack-knifing of road trains. Also tyre pressure monitoring systems and electronic stability programs for the trucks are advised.
In the framework of the OECD study "Moving Freight with Better Trucks", several vehicle combinations which are worldwide in operation were examined regarding different performance criteria. One criterion was the road wear performance of these articulated vehicles. With given tyre and vehicle data (mainly weights and axle loads) the road wear performance was calculated for each vehicle combination. The method according to COST 334 is presented and the vehicle combinations are compared
The Swedish National Road Administration (SNRA), the Japanese Automobile Research Institute (JARI) and the Federal Highway Research Institute (BASt) are co-operating in the International Harmonized Research Activities on Intelligent Transportation Systems (IHRA-ITS). Under this umbrella a joint study was conducted. The overall objective of this study was to contribute to the definition and validation of a "battery of tools" which enables a prediction and an assessment of changes in driver workload due to the use of in-vehicle information systems (IVIS) while driving. In this sense \"validation\" means to produce empirical evidence from which it can be concluded that these methods reliably discriminate between IVIS which differ in terms of relevant features of the HMI-design. Additionally these methods should also be sensitive to the task demands imposed on the driver by the traffic situation and their interactions with HMI-design. To achieve these goals experimental validation studies (on-road and in the simulator) were performed in Sweden, Germany and Japan. As a common element these studies focused on the secondary task methodology as an approach to the study of driver workload. In a joint German-Swedish on-road study the Peripheral Detection Task (PDT) was assessed with respect to its sensitivity to the complexity of traffic situations and effects of different types of navigation systems. Results show that the PDT performance of both the German and the Swedish subjects reflects the task demands of the traffic situations better than those of the IVIS. However, alternative explanations are possible which will be examined by further analyses. Results of this study are supplemented by the Japanese study where informational demands induced by various traffic situations were analysed by using a simple arithmetic task as a secondary task. Results of this study show that relatively large task demands can be expected even from simple traffic situations.
Automated driving will provide many kinds of benefits - some direct and some indirect. The benefits originate at the individual level, from changes in the behaviour of drivers and travellers with regard to driving and mobility, ending up with benefits at the social level via changes in the whole transport system and society, where many of the current planning and operations paradigms are likely to be transformed by automated driving. There may also be disbenefits, particularly at a social level, for example in intensity of travel which could result in additional congestion and increased use of natural resources. There may also be unintended consequences. For example, we do not know the impacts on public transport: driverless vehicles could provide a means to a lower cost service provision, but the availability of automated cars could lead to more car travel at the expense of collective transport.
The incidence of side impacts was investigated from GIDAS data. Both vehicle-fixed object and vehicle-vehicle collisions were analysed as these are enclosed within the consumer testing program. Vehicle-fixed object collisions were stratified according to ESC availability. Results indicated that vehicles equipped with ESC rarely have pure-lateral impacts. An increase in oblique collisions was seen for the vehicles with ESC whereby most vehicle were driving in left curves. The analysis of vehicle-vehicle collisions developed injury risk curves were developed at the AIS3+ injury severity for the vehicle-vehicle side impacts. Results suggested that greatest injury risk occurred when a Pre Euro NCAP vehicle was struck by a Post Euro-NCAP vehicle. The remaining curves did not show different behaviour, indicating that stiffness increased have been equally combated. This was attributable to the few Post Euro-NCAP vehicles that had a deployed curtain airbag available in the sample. The integration of Euro NCAP testing has shown to improve vehicle crashworthiness for pole collisions, as those vehicles with ESC rarely incur lateral impacts.
The levels of continuous vehicle automation have become common knowledge. They facilitate overall understanding of the issue. Yet, continuous vehicle automation described therein does not cover "automated driving" as a whole: Functions intervening temporarily in accident-prone situations can obviously not be classified by means of continuous levels. Continuous automation describes the shift in workload from purely human driven vehicles to full automation. Duties of the driver are assigned to the machine as automation levels rise. Emergency braking, e.g., is obviously discontinuous and intensive automation. It cannot be classified under this regime. The resulting absence of visibility of these important functions cannot satisfy " especially in the light of effect they take on traffic safety. Therefore, in order to reach a full picture of vehicle automation, a comprehensive approach is proposed that can map out different characteristics as "Principle of Operation" at top level. On this basis informing and warning functions as well as functions intervening only temporarily in near-accident situations can be described. To reach a complete picture, levels for the discontinuous, temporarily intervening functions are proposed " meant to be the counterpart of the continuous levels already in place. This results in a detailed and independent classification for accident-prone situations. This finally provides for the visibility these important functions deserve.
Accidents between right turning trucks and straight riding cyclists often show massive consequences. Accident severity is much higher than in other accidents. The situation is critical especially due to the fact that, in spite of the six mirrors that are mandatory for ensuring a minimum field of sight for the truck drivers, cyclists in some situations cannot be seen or are not seen by the driver. Either the cyclist is overlooked or is in a blind spot area that results from the turning manoeuvre of the truck and its articulation if it is a truck trailer or truck semitrailer combination. At present driver assistance systems are discussed that can support the driver in the turning situation by giving a warning when cyclists are riding parallel to the truck just before or in the turning manoeuvre. Such systems would generally bear a high potential to avoid accidents of right turning trucks and cyclists no matter if they ride on the road or on a parallel bicycle path. However, performance requirements for such turning assist systems or even test procedures do not exist yet. This paper describes the development of a testing method and requirements for turning assist systems for trucks. The starting point of each development of test procedures is an analysis of accident data. A general study of accident figures determines the size of the problem. In-depth accident data is evaluated case by case in order to find out which are representative critical situations. These findings serve to determine characteristic parameters (e.g. boundary conditions, trajectories of truck and cyclist, speeds during the critical situation, impact points). Based on these parameters and technical feasibility by current sensor and actuator technology, representative test scenarios and pass/fail-criteria are defined. The outcome of the study is an overview of the accident situation between right turning trucks and straight driving cyclists in Germany as well as a corresponding test procedure for driver assistance systems that at this first stage will be informing or warning the driver. This test procedure is meant to be the basis for an international discussion on introducing turning assist systems in vehicle regulations.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
Fahrerassistenzsysteme unterstützen den Fahrer durch Information, Warnung oder Eingriff in die Fahrzeugsteuerung. Zukünftige Systeme zur Kollisionsvermeidung oder bis hin zum automatischen Fahren werden den Fahrer immer mehr entlasten. Wegen ihres erheblichen Potenzials zur Verbesserung vor allem der aktiven Sicherheit können die Fahrerassistenzsysteme wesentlich zur Vermeidung von Unfällen oder der Reduktion von Unfallfolgen beitragen. Andererseits können Fahrerassistenzsysteme aufgrund des komplexen Systemzusammenhangs zwischen Fahrer, Fahrzeug und Umwelt negative Auswirkungen auf das Verkehrsgeschehen haben. Dieser Aspekt muss schon bei der Entwicklung der Systeme berücksichtigt werden. Die Empfehlung der Europäischen Kommission zur Gestaltung von Informations- und Kommunikationssystemen gibt dazu Leitlinien vor. Die BASt ist mit der wissenschaftlichen Begleitung der Thematik beauftragt. Die Industrie ist dazu aufgefordert darzulegen, welche Maßnahmen zur Einhaltung der Grundsätze ergriffen worden sind beziehungsweise werden. Um das Potenzial der Fahrerassistenzsysteme zur Steigerung der Verkehrssicherheit voll ausschöpfen zu können, sind weiterhin Forschungsarbeiten zur Entwicklung neuer und zur Weiterentwicklung bestehender Systeme unter Berücksichtigung der Gestaltungsanforderungen für sichere Assistenzsysteme durchzuführen.
Since 2005 the German In-Depth Accident Study (GIDAS) also records aspects of active vehicle safety. This is done because vehicles are fitted with an increasing number of active safety devices which have undoubtedly an influence on the number, severity and course of accidents. Accident researchers expect that collecting active safety data will facilitate to assess and quantify the impact of these and future devices. It is the aim of this paper to outline benefits and limitations associated with the recording of active safety aspects within indepth studies. An overview about possible areas where active safety data can be useful will be given. For that purpose single safety or comfort systems will be selected to estimate the effects of an accident database which includes variables associated with these systems. Questions with regard to the limitations of collecting active safety data will be addressed. Possible items are for example the usability of the data recorded, the real accident cause, the small number of relevant accidents, the time span needed to gather a sufficient dataset, the small share of vehicles equipped with a certain system or different functionalities of systems that are supposed to fall in the same category. As a result user needs for a reasonable data collection of active safety elements will be elaborated.
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of synthetic and plastic materials as a material for the interior equipment of buses and coaches because of their ood mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years - also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, the production of smoke, the smoke development and propagation and its toxicity for the people as well as the testing methods and limit values are of interest. For those reasons research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behavior of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and on-board extinguishing equipment were elaborated. At the other hand research is carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. The paper describes which effective and economically reasonable fire safety requirements for interiors of buses would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses.
Except for corrective steering functions automatic steering is up to now only allowed at speeds up to 10 km/h according to UN Regulation No. 79. Progress in automotive engineering with regard to driver assistance systems and automation of driving tasks is that far that it would be technically feasible to realise automatically commanded steering functions also at higher vehicle speeds. Besides improvements in terms of comfort these automated systems are expected to contribute to road traffic safety as well. However, this safety potential will only be exhausted if automated steering systems are properly designed. Especially possible new risks due to automated steering have to be addressed and reduced to a minimum. For these reasons work is currently ongoing on UNECE level with the aim to amend the regulation dealing with provisions concerning the approval of steering equipment. It is the aim to revise requirements for automatically commanded steering functions (ACSF) so that they can be approved also for higher speeds if certain performance requirements are fulfilled. The paper at hand describes the derivation of reasonable system specifications from an analysis of relevant driving situations with an automated steering system. Needs are explained with regard to covering normal driving, sudden unexpected critical events, transition to manual driving, driver availability and manoeuvres to reach a state of minimal risk. These issues form the basis for the development of test procedures for automated steering to be implemented in international regulations. This holds for system functionalities like automatic lane keeping or automatic lane change as well as for addressing transition situations in which the system has to hand over steering to the driver or addressing emergency situations in which the system has to react instead of the driver.
Automatische Lenkfunktionen sind abgesehen von korrigierenden Lenkeingriffen entsprechend der UN-Regelung Nr. 79 bisher nur in einem Geschwindigkeitsbereich bis 10 km/h erlaubt. Die Weiterentwicklung der Technik im Bereich der Fahrerassistenzsysteme und der Automatisierung der Fahraufgabe wuerden es jedoch technisch erlauben, automatische Lenkfunktionen auch bei höheren Geschwindigkeiten einzusetzen. Neben einem Zugewinn an Komfort wird von diesen Systemen auch ein Beitrag zur Erhöhung der Verkehrssicherheit erwartet. Dieses Verkehrssicherheitspotenzial wird man jedoch nur ausschöpfen können, wenn die automatisierten Lenksysteme entsprechend gestaltet sind. Insbesondere sollten mögliche Risiken auf Grund automatischen Lenkens minimiert sein. Aus diesen Gründen laufen derzeit Arbeiten auf UNECE-Ebene, die Regelung Nr. 79 über einheitliche Bedingungen für die Genehmigung der Fahrzeuge hinsichtlich der Lenkanlage in Bezug auf automatische Lenkfunktionen (ACSF = Automatically Commanded Steering Functions) zu überarbeiten, um diese unter bestimmten Bedingungen auch bei höheren Geschwindigkeiten genehmigen zu können. Der vorliegende Beitrag reflektiert diese Arbeiten und stellt die Entwicklung der technischen Anforderungen an automatisches Lenken und der für die fahrzeugtechnischen Vorschriften vorgesehenen Testprozeduren dar.
Mit der EU-Verordnung Nummer 661/2009 zur Typgenehmigung und allgemeinen Sicherheit von Kraftfahrzeugen wird von der EU für schwere Nutzfahrzeuge der Einbau von Spurverlassenswarnsystemen und automatischen Notbremssystemen vorgeschrieben. Mit dem obligatorischen Einbau der Systeme wird eine Reduktion der Abkommens- und Auffahrunfälle von Nutzfahrzeugen aus den Klassen M2, M3, N2 und N3, die auf Grund der hohen Masse der Fahrzeuge folgenschwer sind, erwartet. Als Einführungsdaten werden der 1. November 2013 für neue Fahrzeugtypen und der 1. November 2015 für neue Fahrzeuge genannt. Leistungsanforderungen beziehungsweise technische Spezifikationen, denen die Systeme genügen müssen, liegen jedoch noch nicht vor. Diese werden derzeit von einer Expertengruppe auf UN-ECE-Ebene entwickelt. Dabei wird versucht, technologieneutrale Beschreibungen für die Ausgestaltung der Systeme zu erstellen, die gleichzeitig sowohl den gewünschten Nutzen für die Verkehrssicherheit garantieren, sich aber auch an der derzeit vorhandenen und realisierbaren Technologie orientieren. Darüber hinaus müssen die Systemkosten in einem vernünftigen Verhältnis zum Sicherheitsnutzen stehen. Ziel ist es, im Laufe des Jahres 2011 Vorschläge für die Legislative vorzulegen. Es wird über den Stand der Arbeiten, offene Fragestellungen, Herausforderungen bei der Ausgestaltung der technischen Anforderungen sowie sich abzeichnende Ergebnisse berichtet. Dabei sind die Arbeiten in Bezug auf Lane Departure Warning Systems (LDWS) bereits weiter fortgeschritten als zu Advanced Emergency Braking Systems (AEBS).
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
Der Beitrag behandelt ein Forschungsvorhaben, das die Instandsetzung und Ertüchtigung von Stahlbrücken, deren orthotrope Fahrbahntafeln durch Rissbildung beschädigt sind, die vorzugsweise im Bereich von Schweissnähten zwischen den Anschlüssen der Längsrippen und dem Deckblech aufgetreten ist, zum Ziel hat. Ursache der Schäden sind Materialermüdung infolge des stark gestiegenen Verkehrsaufkommens schwerer Fahrzeuge gegenüber der Bauzeit in den sechziger Jahren und die seitdem erheblich gestiegenen Achslasten. Durch das kraftschlüssige Aufkleben von Stahlblechen auf das Deckblech sollen dessen Steifigkeit erhöht und damit die Durchbiegungen verringert werden. Die Spannungen in den anschliessenden Schweissnaehten nehmen ab und können bei ausreichender Dicke des aufzuklebenden Bleches auf eine nicht mehr ermüdungsrelevante Größenordnung zurückgefuehrt werden. Wegen der sehr komplexen Gesamtaufgabe wurden die Untersuchungen in vier Teilbereiche aufgegliedert: 1. Computer-Simulation der Beanspruchung einer orthotropen Platte unter einem normierten Ermüdungslastmodell. 2. Optimierung der Klebtechnologie. 3. Dauerfestigkeitsuntersuchungen (Versuche). 4. Entwicklung und Prüfung von Konstruktionsdetails. Die Projekte 1 und 2 sind bereits erfolgreich abgeschlossen. Das Projekt 3 steht kurz vor dem Abschluss (10/2005). Projekt 4 wird in 2006 durchgeführt.
Die Bundesanstalt für Straßenwesen (BASt) ist an mehreren Forschungsvorhaben im Zusammenhang mit der Instandsetzung und Verstärkung von orthotropen Fahrbahnplatten beteiligt. Der Beitrag stellt die dabei gemachten Erfahrungen und die Entwicklungen der Verstärkungsverfahren in einem Überblick dar. Ein Großteil der Stahlbrücken wurde in Deutschland in den 1960er und 1970er Jahren nach den damals gültigen Regelwerken gebaut. Bei Erstellung dieser Regelwerke war die ermüdungswirksame Belastung durch den rasant steigenden Schwerlastverkehr nicht absehbar. Die damals erstellten Bauwerke weisen nach heutigem Kenntnisstand daher teilweise Defizite auf, die zu Schäden in Form von Schweißnaht- und Blechrissen geführt haben, die zu aufwändigen Instandsetzungen führten. Die Schäden werden in vier Kategorien eingeteilt, die sich jeweils beziehen auf die Anschlüsse am Deckblech, im Längssystem (Längssteifen), im Quersystem (Querträger) sowie im Hauptsystem (Hauptträger). Bei Anschlüssen im Hauptsystem sind bisher jedoch keine Schäden bekannt. Da das Deckblech und seine Anschlüsse infolge der direkten Lasteintragung durch die Reifen besonders gefährdet sind, konzentrieren sich die aktuellen Untersuchungen zu Instandsetzungsmethoden auf die dort aufgetretenen Schäden. Erfolgversprechend haben sich herausgestellt: direkte Deckblechverstärkung durch Stahlbleche, Aufbringen einer Sandwichplatte (Sandwich-Plate-System (SPS)) und Aufbringen von hochfestem bewehrten Stahlfaserbeton sowie die Verbesserung der Mitwirkung des Fahrbahnbelages durch erhöhte Steifigkeit des Asphaltbelags (zum Beispiel hohlraumreiches Asphaltgerüst mit nachträglichem Verguss) und bessere Haftung. Alle Varianten verringern die lokalen Spannungen und Verformungen signifikant und bewirken dadurch einen erhöhten Ermüdungswiderstand.
Der folgende Beitrag liefert einen Überblick über den Bestand der Stahlbrücken im Bundesfernstraßennetz und enthält eine Zusammenstellung unterschiedlicher Ertüchtigungsmßsnahmen. Damit bietet er eine wichtige Orientierungshilfe für die Ausrichtung der zukünftigen Forschungsschwerpunkte. Es wird deutlich, dass bei der Entwicklung von Verstärkungsmaßnahmen vordringlicher Forschungsbedarf besteht.
Die überarbeiteten neugefassten Begutachtungsleitlinien zur Kraftfahreignung beinhalten zum ersten Mal Leitlinien aus medizinischer und psychologischer Sicht. Sie entstanden durch die Zusammenführung der fünften Auflage der Begutachtungsleitlinien Krankheit und Kraftverkehr und des Psychologischen Gutachtens Kraftfahreignung. Die Leitlinien gründen auf den Ausführungen der Zweiten Führerscheinrichtlinie der EG und der neuen Fahrerlaubnisverordnung.
Im Rahmen des weltweiten ESV-Programmes (Enhanced Safety of Vehicles) werden seit mehreren Jahren internationale Forschungsbemühungen unternommen (International Harmonized Research Activities, IHRA), um im Vorfeld der Gesetzgebung die wissenschaftlichen Grundlagen gemeinsam zu erarbeiten. Ziel der IHRA-Arbeiten ist es, auf der Grundlage dieser Forschungsergebnisse die Harmonisierung der Vorschriften zu erleichtern. Eine besondere Aktivität bezieht sich auf Intelligent Transportation Systems (ITS). Im vorliegenden Beitrag wird die Aufgabe dieser IHRA-ITS-Arbeiten geschildert, sowie der derzeitige Stand der Forschungsbemühungen beschrieben. Es zeigt sich, dass die beschriebene Sicherheitsbewertung eine Fülle von Fragestellungen aufwirft und weitere Forschungsanstrengungen erfordert. Die zukünftigen Bemühungen sind darauf gerichtet, in internationaler Zusammenarbeit und Arbeitsteilung die als besonders wichtig erkannten Themen zur Bewertung der fahrzeugseitigen Fahrerassistenzsysteme zu bearbeiten.
Die neuen Begutachtungs-Leitlinien "Krankheit und Kraftverkehr" bringen nicht nur eine Angleichung der 4. Auflage des Gutachtens Krankheit und Kraftverkehr an den Text und die Systematik der 2. EG-Richtlinie, sondern auch eine Reihe wichtiger neuer Erkenntnisse entsprechend dem Fortschritt der Medizin in Diagnostik und Therapie. So wurden insbesondere die Beurteilungen von Krankheiten des Nervensystems, der psychischen Erkrankungen und Auffälligkeiten, der Zuckerkrankheit und der Sucht bezüglich der Kraftfahreignung neu formuliert.
Internationale Aktivitäten der Forschung auf dem Gebiet "Passive Sicherheit von Kraftfahrzeugen"
(2000)
Eine Fülle von Aktivitäten ist derzeit auf den Gebieten Frontal- und Seitenstoß zu beobachten, die in Europa auf den beiden entsprechenden EG-Richtlinien aufbauen. Das EEVC führt seine Arbeiten, an denen die Automobilindustrie beteiligt ist, fort; hier sind insbesondere die Arbeiten zum Seitenstoß (Kopfaufprall und Barrierenvergleich) zu nennen. Auf weltweiter Ebene beginnen die Arbeiten der IHRA (International Harmonised Research Activities) in ein konkretes Stadium der Zusammenarbeit einzutreten. Auf dem Gebiet der Seitenkollision ist längerfristig ein neues Testverfahren geplant, in das der von ISO entwickelte WORLD-SID einbezogen werden soll. Es gibt derzeit viele ernsthafte Bemühungen der Forschung um Harmonisierung. Auch wenn es nicht zu einer weltweiten Harmonisierung kompletter Regelungen kommt, so gibt es doch Hoffnung auf eine weltweite Harmonisierung von definierten Teilbestimmungen in speziellen Regelungen, so zum Beispiel bezüglich der Testmethode, der Versuchspuppen und der Bewertung der Schutzkriterien. Der Name des EEVC, European Enhanced Vehicle-safety Committee, steht für die Weiterentwicklung der Fahrzeugsicherheit. Die beteiligten Regierungen sind überzeugt, dass moderne Technologien neue Möglichkeiten eröffnen, um die Sicherheit der Kraftfahrzeuge weiter zu verbessern.
Ausgehend von den Unfalldaten der letzten Jahre wird die Bedeutung von Fußgängerunfällen im Unfallgeschehen dargestellt. Betrachtet man die bei Unfällen getöteten Verkehrsteilnehmer, so sind am häufigsten Personen in Kraftfahrzeugen betroffen. Am zweithäufigsten werden, gemäß der Unfallstatistik, Fußgänger getötet. Eine Möglichkeit zur Verbesserung des Schutzes von Fußgängern und anderen sogenannten "ungeschützten Verkehrsteilnehmern" im Falle einer Kollision mit einem Kraftfahrzeug sind Maßnahmen am Fahrzeug. Um die Wirksamkeit derartiger Maßnahmen zu beurteilen, wurde durch das EEVC (European Enhanced Vehicle-Safety Committee) ein Prüfverfahren entwickelt. Es handelt sich dabei um ein Komponentenprüfverfahren, mit dem die Frontstruktur von Fahrzeugen, die bei einer Kollision mit einem Fußgänger hauptsächlich betroffen ist, geprüft wird. Es werden keine den gesamten Menschen repräsentierende Dummies verwendet, stattdessen werden Prüfkörper, die einzelne Körperteile simulieren, eingesetzt. Dieser EEVC Vorschlag wird geschildert. Darüber hinaus wird über Aktivitäten außerhalb des EEVC berichtet, sowie über den aktuellen Stand der Bemühungen der Europäischen Kommission in Bezug auf den Fußgängerschutz, die derzeit, auf Grundlage des Prüfvorschlages des EEVC, einen Vorschlag für eine Europäische Richtlinie erarbeitet.
EEVC Status report
(2001)
Die Erste Richtlinie des Rates zur Einführung eines EG-Führerscheins ist Ende 1980 verabschiedet worden. Der Anhang III dieser Richtlinie befasst sich mit den Mindestanforderungen an die körperliche und geistige Tauglichkeit der Fahrzeugführer. Diese Anforderungen sind über 10 Jahre alt und bedürfen einer Überprüfung. Der Autor berichtet über die Vorschläge, welche eine Sondergruppe von Regierungsexperten der Kommission der EG unterbreitet hat. Erläutert werden die Anforderungen an: Sehvermögen, Herz- und Gefäßkrankheiten, Zuckerkrankheit, Krankheiten des Nervensystems, Geistige Störungen, Drogen- und Arzneimittelmissbrauch sowie Nierenerkranken.
Straßentunnel mit integriertem Rettungsweg: Konstruktions- und betriebliche Sicherheitsaspekte
(2009)
Infolge der seit 2003 in den RABT formulierten schärferen Sicherheitsanforderungen ist für Gegenverkehrstunnel bei Neuplanungen und bautechnischen Nachrüstungen häufig die Anordnung eines parallel zur Hauptröhre verlaufenden Rettungsstollens erforderlich. Untersuchungen der Bundesanstalt für Straßenwesen (BASt) zur Wirtschaftlichkeit verschiedener aktueller und auch neuer Querschnittsvarianten haben gezeigt, dass insbesondere ein Querschnitt mit integriertem begehbarem Rettungsweg unter bestimmten Voraussetzungen Kostenvorteile gegenüber der Regellösung mit parallelem Rettungsstollen bietet. In ergänzenden Untersuchungen wurden konstruktive und sicherheitstechnische Detailfragen für einen Regelquerschnitt mit integriertem Rettungsweg untersucht und bewertet und ein Kostenvergleich mit der Regellösung mit parallelem Rettungsstollen wurde durchgeführt.
Pedestrians represent about 20% of the overall fatalities in Europe- road traffic accidents. In this paper a methodology is proposed to understand why the numbers are so high, especially in the south of Europe and particularly in Portugal, . First a detailed statistical analysis using Ordinal Logistic Regression model (OLR) was applied to the gathered data from all Portuguese accidents with victims in the period 2010-2012. In a second stage accident reconstruction computational techniques using pedestrian biomechanical models are used to evaluate the accident conditions that lead to the injuries, such as the speed and the impact location. For biomechanical injury criterions, the AIS (Abbreviated Injury Scale), the HIC (Head Injury Criterion) and other injury criterions based on the resulting accelerations in the pedestrian's body are used. The statistical model reported that there were several predictors that significantly influenced the pedestrian injury severity in the event of a road accident, such as Pedestrian's age, Pedestrian's gender, Vehicle Design/Category or Driver's gender. The use of injury scales and biomechanical criterions in in-depth investigation of road accidents, such as AIS, can significantly improve the quality of the reconstruction process.
Es werden erste Ergebnisse des von der Bundesanstalt für Straßenwesen (BASt) geförderten Forschungsprojekts "Hauptstudie zur Wirksamkeit von Tunnelwänden als Träger photokatalytischer Oberflächen" (FE 9.0184/2011/ARB) vorgestellt. Ziel war die Erarbeitung von technischen Lösungen zur Stickoxidreduktion an einem Tunnelstandort durch die Konzeptionierung und den Bau abgeschlossener photokatalytischer Reaktoren (Tunnelkassetten) sowie deren Validierung im Tunnel "Rudower Höhe" an der Bundesautobahn A113 in Berlin. Dabei wird künstliches UV-Licht als Energiequelle für den Schadstoffabbau eingesetzt. Es wird speziell über die Modellierungen berichtet, mit Hilfe derer die Tunnelkassetten sowohl strömungstechnisch als auch in Hinblick auf den photokatalytischen Abbauwirkungsgrad optimiert wurden.
This paper set out to examine the possibilities for injury avoidance implications for older drivers in crashes, based on crash and injury patterns among older drivers and current trends in ageing in most western societies. A number of safety technologies were identified and discussed which have potential for improving vehicle older driver crash avoidance and crashworthiness. While there were some promising estimates available of the likely benefits of this technology for improving safety, it is evident that they need to be confirmed for older drivers, given their age-related disabilities and sensory limitations. Further research is urgently required to ensure that these technologies yield safety benefits without any disbenefits for older drivers.rn
Whiplash injuries are characterized by the high variability of its symptoms and by the subjectivity of its diagnosis, which sometimes leads to frauds perpetrated by victims of rear-end impacts. It is estimated that whiplash injuries cost annually about 10.000 million Euros in Europe. Therefore, the aim of this study was to investigate the influence of the dynamics of the accident in which the victim was involved in the probability of development of whiplash associated injuries. In the presented methodology, first an accident reconstruction is performed where the dynamics of the accident is determined. This is carried out using the software PC-Crash, police and insurance companies' data. Then biomechanical injuries criteria related with whiplash injuries are evaluated. For the evaluation of the probability of having whiplash injuries, the Neck Injury Criterion (NIC) of the victim and the mean acceleration of the vehicle were evaluated. Then, with medical reports, the results of the accident reconstruction are correlated with the reported injuries. Some examples are presented. The results obtained indicate that the study of the dynamics of the road accidents in which the victims were involved could be used as an auxiliary of the prognosis of whiplash injuries and is important for a precise diagnosis of this type of injuries.
A national initiative from the vehicle manufacturers, safety system suppliers, the road administration and universities in Sweden took off in 2007. The aim was to develop a national investigation network and a methodology focusing on all phases of a crash (pre-crash, in-crash and post-crash) as well as all parts of the road transport system (road user, vehicle and road environment). The initiative is formally run as a project with the acronym INTACT (Investigation Network and Accident Collection Techniques). It was a three year pilot with the aim to develop methodologies for an extended national crash investigation activity. During the first year the INTACT partners agreed on the aim for the investigation and methods for retrieving the data were developed. During the second and third year the methodology was tested in real-world investigations and further refinement was made. The paper describes the methodology developed to obtain high qualitative in-depth road crash data.
The overall purpose of the ASSESS project is to develop a relevant and standardised set of test and assessment methods and associated tools for integrated vehicle safety systems, primarily focussing on currently available pre-crash sensing systems. The first stage of the project was to define casualty relevant accident scenarios so that the test scenarios will be developed based on accident scenarios which currently result in the greatest injury outcome, measured by a combination of casualty severity and casualty frequency. The first analysis stage was completed using data from a range of accident databases, including those which were nationally representative (STATS19, UK and STRADA, SE) and in-depth sources which provided more detailed parameters to characterise the accident scenarios (GIDAS, DE and OTS, UK). A common analysis method was developed in order to compare the data from these different sources, and while the data sets were not completely compatible, the majority of the data was aligned in such a way that allowed a useful comparison to be made. As the ASSESS project focuses on pre-crash sensing systems fitted to passenger cars, the data selected for the analysis was "injury accidents which involved at least one passenger car". The accident data analysis yielded the following ranked list of most relevant accident scenarios: Rank Accident scenario 1 Driving accident - single vehicle loss of control 2 Accidents in longitudinal traffic (same and opposite directions) 3 Accidents with turning vehicle(s) or crossing paths in junctions 4 Accidents involving pedestrians The ranked list highlights the relatively large role played by "accidents in longitudinal traffic", and "accidents with turning vehicle(s) or crossing paths in junctions" (the second and third most prevalent accident scenarios, respectively). The pre-crash systems addressed in ASSESS propose to yield beneficial safety outcomes with specific regard to these accident scenarios. This indicates that the ASSESS project is highly relevant to the current casualty crash problem. In the second stage of the analysis a selection of these accident scenarios were analysed further to define the accident parameters at a more detailed level .This paper describes the analysis approach and results from the first analysis stage.
The SafetyNet project was formulated in part to address the need for safety oriented European road accident data. One of the main tasks included within the project was the development of a methodology for better understanding of accident causation together with the development of an associated database involving data obtained from on-scene or "nearly onscene" accident investigations. Information from these investigations was complemented by data from follow-up interviews with crash participants to determine critical events and contributory factors to the accident occurrence. A method for classification of accident contributing factors, known as DREAM 3.0, was developed and tested in conjunction with the SafetyNet activities. Collection of data and case analysis for some 1 000 individual crashes have recently been completed and inserted into the database and therefore aggregation analyses of the data are now being undertaken. This paper describes the methodology development, an overview of the database and the initial aggregation analyses.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
The objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria and limits for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configurations such as impacts with car sides, trucks, and pedestrians. The WG consists of national government representatives who are supported by industrial advisers. The WG serves as a focal point for European research conducted by national and industry sponsored projects. The WG is responsible for collating the results from this research to achieve its objectives. EEVC WG 15 serves as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the Development of Crash Test Procedures"(VC-COMPAT) project partly funded by the European Commission. This paper presents a review of the current European research status. It also identifies current issues with candidate test procedures and lists the parameters that should be considered in assessing compatibility. The current candidate test procedures are: an offset barrier test with the progressive deformable barrier (PDB) face; a full width wall test with or without a deformable aluminium honeycomb face and a high resolution load cell wall; an offset barrier test with the EEVC barrier and load cell wall. These candidate test procedures must allow assessment of structural interaction, frontal force levels and compartment strength. The WG will report its findings to the EEVC Steering Committee and propose a test procedure in November 2006.
Bewertung der Fahrzeug-Fußraumintrusionen beim Offset Frontaltest gegen das Verformungselement
(1998)
In den Tests nach dem neuen Frontaltestverfahren (Entwürfe ECE R.94 sowie Richtlinie 96/79/EG und Ergänzung zu RL 70/156/EWG) entstehen hohe Verformungen der Fußräume der Versuchsfahrzeuge. Die Bewertung der Gefährdung der Insassen durch Intrusion, vorwiegend der Spritzwand begleitet von heftigen Bewegungen der Pedale, soll durch am Dummy zu messende Schutzkriterien erfolgen. Es ist vorgesehen, an den Dummies die Verschiebung des Schienbeins gegen das Knie, die Längskraft im Unterschenkel und den sogenannten Tibia Index zu messen. Um dieses zu ermöglichen, mussten an den vorhandenen Dummy-Unterschenkeln konstruktive Änderungen vorgenommen werden. Über die Herleitung der Schutzkriterien, Fragen bei der Anwendung dieser Kriterien sowie die technischen Einzelheiten und die Zertifizierung der neuen Dummy-Unterschenkel, welche die erforderlichen Messungen erlauben, wird berichtet.
The main focus of the benefit estimation of advanced safety systems with a warning interface by simulation is on the driver. The driver is the only link between the algorithm of the safety system and the vehicle, which makes the setup of a driver model for such simulations very important. This paper describes an approach for the use of a statistical driver model in simulation. It also gives an outlook on further work on this topic. The build-up process of the model suffices with a distribution of reaction times and a distribution of reaction intensities. Both were combined in different scenarios for every driver. Each scenario has then a specific probability to occur. To use the statistical driver model, every accident scene has to be simulated with each driver scenario (combinations of reaction times and intensities). The results of the simulations are then combined regarding the probabilities to occur, which leads to an overall estimated benefit of the specific system. The model works with one or more equipped participants and delivers a range for the benefit of advanced safety systems with warning interfaces.
Millions of kilometers are driven and recorded by car manufacturers and researchers every year to gather information about realistic traffic situations. The focus of these studies is often the recording of critical situations to create test scenarios for the development of new systems before introducing them into the market. This paper shows a novel Analysis and Investigation Method for All Traffic Scenarios (AIMATS) based on real traffic scenes. It also shows how to get detailed information about speeds, trajectories and behavior of all participants without driving thousands of kilometers at the example of conflict situations with animals. Basis of the AIMATS is the identification of the most relevant locations as "Points of Interest" (POI), the recording of the critical situations and their "base lines" at these POI. This paper presents a new method to identify critical scenarios involving both vehicles and animals as well as preliminary results of a study done in Saxony using this new method.
The focus of the technical innovation in the automobile industry is currently changing to sensor based safety systems, which are operating in the pre-crash phase of an accident. To get more information about this pre-crash phase for real accidents a simulation of this phase using the GIDAS database is done. The basics for this simulation are geometrical information about the accident location and the exact accident data out of the GIDAS database. This aggregated information gives the possibility to simulate an exact motion for every accident participant, using MATLAB / SIMULINK, in the pre-crash phase. After the simulation the information about the geometrical positions, the velocities and maneuvers of the drivers to an individual TTC (time to collision) are available. With those results it is possible to develop new useful sensor geometries using pre-crash scatter plots or estimate the efficiency of implemented active safety systems in combination with sensor characteristics. This simulation can be done for every reconstructed accident included in the GIDAS database, so these results can represent a wide spread basis for the further development of active safety systems and sensor geometries and characteristics
Entgegen populären Meinungen, welche älteren Kraftfahrern ein generelles Gefahrenpotenzial für die allgemeine Verkehrssicherheit zuschreiben, weisen die Unfallstatistiken eher auf eine besondere Gefährdung dieser Gruppe von Verkehrsteilnehmern hin, woraus sich Forderungen nach einer zielgruppenspezifischen Verkehrssicherheitsarbeit begründen. Kompetentes und damit sicheres Verhalten kann als Ergebnis der Passung zwischen den individuell verfügbaren Ressourcen und den Anforderungen der Umwelt betrachtet werden. Überschreiten die Umweltanforderungen die Verhaltenspotenziale des Individuums, kann es zu Überforderung kommen. Verdeutlichen lässt sich diese Perspektive durch genaue Betrachtung von Verkehrsunfällen unter Beteiligung älterer Kraftfahrer: So spiegeln die aktuellen Unfallstatistiken aus 2008 wider, dass ein großer Teil der Unfälle von Kraftfahrern im Alter über 65 Jahren auf sogenanntes Fehlverhalten in Knoten, wie z.B. Fehler beim Abbiegen, Ein- und Ausfahren in Kreuzungen und Vorfahrtbeachtung, zurückzuführen sind. Diese im Vergleich zu jüngeren Fahrern häufigere Verwicklung Älterer in Unfälle dieser Art legt nahe, dass es in genau diesen Situationen zu einem Ungleichgewicht zwischen individuell verfügbaren Ressourcen und den Anforderungen der Verkehrsumwelt kommt. Beispielsweise könnten in diesen Situationen Beeinträchtigungen der visuellen Wahrnehmungsfähigkeit, verlangsamte Reaktionszeiten oder auch Einschränkungen der Bewegungsausführung zu einer zu langsamen oder auch falschen Entscheidungsfindung oder Handlungsausführung im Straßenverkehr führen. Dieser Perspektive folgend können Maßnahmen zur Erhöhung der Verkehrssicherheit älterer Kraftfahrer zum einen auf Seiten des Individuums ansetzen und dazu beitragen, die Kompetenzen des älteren Kraftfahrers zu erhöhen, zum anderen Bezug auf den Kontext nehmen, indem durch Anpassungen der Bedingungen der Verkehrsumwelt zur Sicherheit " nicht nur " älterer Kraftfahrer beigetragen wird. Personenzentrierte Ansätze zielen dabei auf die Ausschöpfung der individuellen Potenziale zur Aufrechterhaltung, Verbesserung oder auch Wiederherstellung einer sicheren Verkehrsteilnahme bis ins hohe Lebensalter. Diese Ansätze umfassen Trainings- und Rehabilitationsprogramme der Fahrkompetenz gleichermaßen wie verkehrspädagogische Programme, mediale Informationskampagnen oder auch Beratungsmaßnahmen und Screening-Tests. Eine Schlüsselposition kann in diesem Kontext dem (Haus)-Arzt als Experten hinsichtlich Konstitution und Lebensverhältnissen seines Patienten und Vertrauensperson zukommen. In der Regel passen ältere Kraftfahrer ihr Fahrverhalten ihren individuell verfügbaren Kompetenzen an. Auf diese Weise können altersbegleitende oder auch mit Erkrankungen oder Medikamenteneinnahmen einhergehende Veränderungen der körperlichen oder geistigen Leistungsfähigkeit zumeist erfolgreich kompensiert werden. Personenzentrierten Ansätzen kommt jedoch eine besondere Relevanz für den kleinen Anteil älterer Fahrer zu, welche keine oder nur unzureichende Kompensation aufweisen. Kontextorientierte Ansätze beziehen sich auf Maßnahmen, welche eine möglichst optimale Gestaltung der Bedingungen der Verkehrsumwelt auf die Bedürfnisse und Anforderungen älterer Kraftfahrer herbeiführen sollen. Maßnahmen dieser Art zielen zum Beispiel auf eine Entschleunigung des Straßenverkehrs durch Geschwindigkeitsbegrenzungen oder auch bauliche Maßnahmen. Auch die Potenziale moderner Fahrzeugtechnik werden unter dieser Perspektive zur Erhöhung der Verkehrssicherheit älterer Fahrer nutzbar. So können Fahrerassistenz- oder Fahrerinformationssysteme den älteren Fahrer in komplexen Situationen unterstützen. Dabei ist der Nutzen für die Verkehrssicherheit jedoch stark von der Handhabbarkeit und Bedienqualität der technischen Hilfsmittel abhängig. Technologien, welche die Komplexität der Fahrzeugbedienung erheblich erhöhen oder die Aufmerksamkeit vom Straßenverkehr ablenken, können ggf. auch zu einer weiteren Diskrepanz zwischen Anforderungssituation und verfügbaren Kompetenzen beitragen. Neben diesen eher auf die individuelle Verkehrsteilnahme als Autofahrer bezogenen Maßnahmen sind weitere wichtige kontextorientierte Ansatzpunkte in alternativen Mobilitätsvarianten zum Auto, wie in der Verbesserung der Attraktivität von Angeboten des ÖPNV oder auch den Bedingungen für Fußgänger und Radfahrer, zu finden. In diesem Sinne erscheint ein mehrdimensionaler Ansatz für die Gestaltung von Maßnahmen zur Erhöhung der Verkehrssicherheit älterer Kraftfahrer am erfolgversprechendsten. Interventionsansätze sollten sich gegenseitig ergänzen und möglichst sowohl die Ressourcen auf Seiten des älteren Menschen selbst als auch der Umwelt umfassen.
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
In Deutschland werden als passive Schutzeinrichtungen an Straßen Stahlschutzplanken und in jüngerer Zeit auch vermehrt Betonschutzwände eingesetzt. Auf dem Gebiet der Schutzeinrichtungen wird es demnächst europäisch harmonisierte Normen geben. Durch ihre Einführung, vermutlich noch in 1997, kommt es auch in Deutschland zur Veränderung der Anforderungen an Schutzeinrichtungen. Die Qualifizierung der in Deutschland nach den Richtlinien für passive Schutzeinrichtungen an Straßen eingesetzten Schutzeinrichtungen nach den europäischen Vorgaben ist durch die Bundesanstalt für Straßenwesen (BASt) in einem Forschungsprojekt für das Bundesverkehrsministerium erfolgt. Die BASt hat ein weiteres Projekt initiiert mit dem Ziel, die wichtigsten Ausführungsformen zu untersuchen und zu weitergehenden Kenntnissen über die hier eingesetzten Schutzeinrichtungen zu kommen. Berichtet wird über wesentliche Ergebnisse aus diesem Projekt.
A set of recommendations for pan-European transparent and independent road accident investigations has been developed by the SafetyNet project. The aim of these recommendations is to pave the way for future EU scale accident investigation activities by setting out the necessary steps for establishing safety oriented road accident investigations in Member States. This can be seen as the start of the process for establishing road accident investigations throughout Europe which operate according to a common methodology. The recommendations propose a European Safety Oriented Road Accident Investigation Programme which sets out the procedures that need to be put in place to investigate a sample of every day road accidents. They address four sets of issues; institutional addressing the characteristics of the programme; operational describing the conditions under which data isrncollected; data storage and protection; and reports, countermeasures and the dissemination of data.rn
Road condition acquisition and assessment are the key to guarantee their permanent availability. In order to maintain a country's whole road network, millions of high-resolution images have to be analyzed annually. Currently, this requires cost and time excessive manual labor. We aim to automate this process to a high degree by applying deep neural networks. Such networks need a lot of data to be trained successfully, which are not publicly available at the moment. In this paper, we present the GAPs dataset, which is the first freely available pavement distress dataset of a size, large enough to train high-performing deep neural networks. It provides high quality images, recorded by a standardized process fulfilling German federal regulations, and detailed distress annotations. For the first time, this enables a fair comparison of research in this field. Furthermore, we present a first evaluation of the state of the art in pavement distress detection and an analysis of the effectiveness of state of the art regularization techniques on this dataset.
The national accident statistics demonstrate that the situation of passenger car side impacts is dominated by car to car accidents. Car side to pole impacts are relatively infrequent events. However the importance of car side to pole impacts is significantly increasing with fatal and seriously injured occupants. For the present study the German in-depth database GIDAS (German In-Depth-Accident Study) and the UK based database CCIS (Co-operative Crash Injury Study) were used. Two approaches were undertaken to better understand the scenario of car to pole impacts. The first part is a statistical analysis of passenger car side to pole impacts to describe the characteristics and their importance relevant to other types of impact and to get further knowledge about the main factors influencing the accident outcome. The second part contains a case by case review on passenger cars first registered 1998 onwards to further investigate this type of impact including regression analysis to assess the relationship between injury severity and pole impact relevant factors.
The role of a national motor vehicle crash causation study-style data set in rollover data analysis
(2010)
On 1 January 2005, The National Highway Traffic Safety Administration, an agency of the United States Department of Transportation, implemented a new data collection strategy designed to assess crash avoidance technologies and report associated behavioral inputs and outcomes. The original goal was a six-year program, however, during the shortened data collection period; it proved a valuable resource for understanding a precrash environment previously obscured by forensic case investigation. Another unintended consequence was an overlap with infrastructure, roadway geometry, and design with the occupant and vehicle outcomes, by virtue of well-defined attributes. External to the collected data, supplementary information was extrapolated, by using manuals published in the United States, by the American Association of State Highway Transportation Officials and selected State Departments of Transportation, in conjunction with the National Motor Vehicle Crash Causation Study (NMVCCS). This provided a backdrop to the infrastructure framework of the rollover problem within which the occupant and vehicle outcomes were studied. If a NMVCCS-style data collection were to be implemented elsewhere, then complementary manuals produced by federal transportation officials might be consulted producing similar relationships. The current study uses NMVCCS data to describe vehicles travelling through diverse design geometries and the outcome for occupants involved in crashes within that system. Codified and extrapolated data form the basis for assessing NMVCCS and its value to the transportation safety community, as the protocols are applicable universally. The benefit in continuing a NMVCCS-style study is noted, as the interaction of roadway infrastructure and occupant protection agencies might find paths to better work together in solving the complex rollover problem using a common data-driven approach.
Verkehrsunfallopfer, die beim Unfall überrollt werden, erleiden fast immer tödliche Verletzungen. Im innerstädtischen Bereich ereignen sich diese Unfälle mehrheitlich im niedrigen Geschwindigkeitsbereich. Die Frage der Vermeidbarkeit des Unfalls wird daher sehr oft seitens der Ermittlungsbehörde an die Sachverständigen gestellt. Im Rahmen der Unfallrekonstruktion spielt der Reifenprofilabdruck am Leichnam eine wichtige Rolle. Er belegt nicht nur den Überrollungsvorgang selbst, sondern erlaubt auch die Identifikation der Überrollungsrichtung und -region, aber auch des in Frage kommenden Reifens. Bei der retrospektiven Analyse von 120 Überrollungsfällen in Berlin (Fußgänger, Radfahrer und Kraftradfahrer) aus den letzten 23 Jahren wurde untersucht, wie verlässlich dieses Merkmal ist, wie oft und wo man es findet und von welchen Faktoren seine Entstehung beeinflusst wird.
To assess occupant safety in a crash test, criteria associating the measurements made with a crash test dummy to injury risk are necessary. To enable better protection of elderly car occupants the objective of this study was to develop improved thoracic injury criteria for the THOR average male dummy. The development of these criteria is usually based on matched dummy and Post Mortem Human Surrogate (PMHS) tests by relating the obtained PMHS injuries to dummy measurements. This approach is limited, since only a few tests in relevant loading conditions are available and any new test series requires high efforts to be performed due to their complexity and costs. To overcome these limitations and to extend the dataset for the development of THOR dummy chest injury risk functions a simulation-based approach was applied within the EC funded project SENIORS (Safety Enhanced Innovations For older Road Users - www.seniors-project.eu). Within this study frontal impact sled simulations with an FE model representing a THOR average male dummy and matched simulations with a human body model (HBM) representing an elderly car occupant were carried out. The HBM used for this study was the THUMS TUC with modified rib cage, which was developed in SENIORS. The modifications included material and geometry changes aiming to represent an elderly car occupant. The rib fracture risk was predicted with a deterministic approach whereby a rib was considered broken when the strain exceeded an age-dependent threshold. Furthermore, a probabilistic method was applied to predict the probability of sustaining a certain number of fractured ribs by comparing local strain values to the distribution of cortical rib ultimate strain. By relating the output from the HBM simulations to a multi-point dummy injury criterion, injury risk curves were calculated by statistical methods. The wide range of loading conditions resulted in the desired range of injuries and THOR ATD output. The number of fractured ribs predicted by the HBM based on the deterministic prediction method was between 0 and 15. Furthermore, the probabilistic risk for the number of rib fractures equal or greater than two, three or four was calculated for each load case. The THOR rib deflection criterion Rmax was between 18 and 56 mm, while the PC Score was in the range of 2.5 to 7.2. Based on these outputs new risk curves for the predicted deterministic (AIS2+/3+) and probabilistic injury risk were calculated. The new curves show reasonable shapes and significance that provide trust in their application. The new risk curves are compared to risk curves obtained by traditional methods. The results were found similar to previous injury risk functions based on physical tests, which gives a high level of confidence in the chosen approach. The simulation-based approach of matched ATD model vs. HBM simulation was successfully applied. Rmax curves show a slightly better quality than the injury criterion PC Score.
Thorax injury is one of main causes of serious injury in frontal collisions, especially for elderly car occupants. The anthropometric test device (ATD) THOR‐M provides chest deflection measurements at multiple locations, to assess the risk of thorax injury. For this purpose e, risk functions are needed that relate the potential criteria based on multipoint chest deflection measurement to in jury risk. Different thorax injury criteria and risk functions for THOR have been proposed [2‐3]. The criteria and functions are based on the traditional approach to developing injury risk functions using matched ATD and PMHS tests by relating the injury (number of fractures) to injury criteria. Regarding these studies, some limitations have been identified, in particular concerning the loading conditions of the data used (mainly 3‐point‐belt loading, high loading severity, out‐of‐date ATD versions. To extend the data set and overcome these limitations, a new approach for improved thorax injury criteria was applied within the EC‐funded project SENIORS. The new approach is based on matched frontal impact sled computer simulations with a model representing the latest THOR‐M ATD version, and matching simulations with a human body model (HBM) representing an elderly car occupant.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
Upcoming test procedures and regulations consider the use of Q-dummies. Especially Q6 and Q10 will be introduced to assess the safety of child occupants in vehicle rear seats. Therefore detailed knowledge of these dummies is important to improve safety. As recent studies have shown, chest deflection measurements of both dummies are influenced by parameters like belt geometry. This could lead to a non optimized design of child restraint systems (CRS) and belt systems. The objective of this study is to obtain a more detailed understanding of the sensitivity of chest measurements to restraint parameters and to investigate the possibilities of chest acceleration as an alternative for the assessment of chest injury risks. A study of frontal impact sled tests was performed with Q6 and Q10 in a generic rear seat environment on a bench. Belt parameters like modified belt attachment locations were varied. For the Q6 dummy, different positioning settings of the CRS (booster with backrest) and of the dummy itself were investigated. The Q10 dummy was seated on a booster cushion. Here the position of the upper belt anchorage point was varied. To simulate the influence of vehicle rotation in the ODB crash configuration, the bench was pre-rotated on the sled in additional tests with the Q10. This configuration was tested with and without pretensioner and load limiter. Chest deflection in Q6 showed a high sensitivity to changes in positioning of the CRS and the dummy itself. A more slouched position of the CRS or dummy resulted in a reduction of measured chest deflection, whereas chest acceleration increased for a more slouched position of the CRS. Chest deflection in Q10 is sensitive to belt geometry as already shown in other studies. In a more outboard position of the shoulder belt anchorage the measured chest deflection is higher. Chest acceleration shows the opposite tendency, which is highest for the rearmost location of the upper belt anchorage. On a pre-rotated bench the highest chest deflection within this test series was observed without load limiter/pretensioner and an outboard belt position. By optimizing the belt location and the use of pretensioner/load limier the chest deflection was significantly reduced. For the Q6 a criterion based on chest acceleration as well as deflection measured at two locations might be the most reliable approach, which requires further research with an additional upper deflection sensor. In the Q10 the measured chest deflection does not always correctly reflect the severity of chest loading. The deflection is depending on initial belt position and restraint parameters as well as test conditions, which result in different directions of belt migration. A3ms chest acceleration might be a better indicator for severity of chest loading independent of different conditions like belt geometries. However, in some cases the benefit of an optimized restraint system could only be shown by deflection. These findings suggest that further research is needed to identify a chest injury assessment method, which could be based on deflection as well as acceleration or other parameters related to belt to occupant interaction.
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
One main objective of the EU-Project SENIORS is to provide improved methods to assess thoracic injury risk to elderly occupants. In contribution to this task paired simulations with a THOR dummy model and human body model will be used to develop improved thoracic injury risk functions. The simulation results can provide data for injury criteria development in chest loading conditions that are underrepresented in PMHS test data sets that currently proposed risk functions are based on. To support this approach a new simplified generic but representative sled test fixture and CAE model for testing and simulation were developed. The parameter definition and evaluation of this sled test fixture and model is presented in this paper. The justification and definition of requirements for this test set-up was based on experience from earlier studies. Simple test fixtures like the gold standard sled fixture are easy to build and also to model in CAE, but provide too severe belt-only loading. On the other hand a vehicle buck including production components like airbag and seat is more representative, but difficult to model and to be replicated at a different laboratory. Furthermore some components might not be available for physical tests at later stage. The basis of the SENIORS generic sled test set-up is the gold standard fixture with a cable seat back and foot rest. No knee restraint was used. The seat pan design was modified including a seat ramp. The three-point belt system had a generic adjustable load limiter. A pre-inflated driver airbag assembly was developed for the test fixture. Results of THOR test and simulations in different configurations will be presented. The configurations include different deceleration pulses. Further parameter variations are related to the restraint system including belt geometry and load limiter levels. Additionally different settings of the generic airbag were evaluated. The test set-up was evaluated and optimized in tests with the THOR-M dummy in different test configurations. Belt restraint parameters like D-ring position and load limiter setting were modified to provide moderate chest loading to the occupant. This resulted in dummy readings more representative of the loading in a contemporary vehicle than most available PMHS sled tests reported in the literature. However, to achieve a loading configuration that exposes the occupant to even less severe loading comparable to modern vehicle restraints it might be necessary to further modify the test set-up. The new generic sled test set-up and a corresponding CAE model were developed and applied in tests and simulations with THOR. Within the SENIORS project with this test set-up also volunteer and PMHS as well as HBM simulations are performed, which will be reported in other publications. The test environment can contribute in future studies to the assessment of existing and new frontal impact dummies as well as dummy improvements and related instrumentation. The test set-up and model could also serve as a new standard test environment for PMHS and volunteer tests as well as HBM simulations.
Thoracic injury is one of the predominant types of severe injuries in frontal accidents. The assessment of the injury risk to the thorax in the current frontal impact test procedures is based on the uni-axial chest deflection measured in the dummy Hybrid III. Several studies have shown that criteria based on the linear chest potentiometer are not sensitive enough to distinguish between different restraint systems, and cannot indicate asymmetric chest loading, which has been shown to correlate to increased injury risk. Furthermore, the measurement is sensitive to belt position on the dummy chest. The objective of this study was to evaluate the optical multipoint chest deflection measurement system "RibEye" in frontal impact sled tests. Therefore the sensitivity of the RibEyesystem to different restraint system parameters was investigated. Furthermore, the issue of signal drop out at the 6 th rib was investigated in this study.A series of sled tests were conducted with the RibEye system in the Hybrid III 50%. The sled environment consisted of a rigid seat and a standard production three-point seat belt system. Rib deflections were recorded with the RibEye system and additionally with the standard chest potentiometer. The tests were carried out at crash pulses of two different velocities (30 km/h and 64 km/h). The tests were conducted with different belt routing to investigate the sensitivity of chest deflection measurements to belt position on the dummy chest. Furthermore, different restraint system parameters were investigated (force limiter level, with or without pretensioning) to evaluate if the RibEye measurements provide additional information to distinguish between restraint system configurations . The results showed that with the RibEye system it was possible to identify the effect of belt routing in more detail. The chest deflections measured with the standard chest potentiometer as well as the maximum deflection measured by RibEye allowed the distinction to be made between different force limiter levels. The RibEye system was also able to clearly show the asymmetric deflection of the rib cage due to belt loading. In some configurations, differences of more than 15 mm were observed between the left and side areas of the chest. Furthermore, the abdomen insert was identified as source of the problem of signal drop out at the 6th rib. Possible solutions are discussed. In conclusion, the RibEye system provided valuable additional information regarding the assessment of restraint systems. It has the potential to enable the evaluation of thoracic injury risk due to asymmetric loading. Further investigations with the RibEye should be extended to tests in a vehicle environment, which include a vehicle seat and other restraint system components such as an airbag.
Für eine Reihe von EU Regelungen im Bereich Fahrzeugsicherheit erlaubt eine Verordnung bereits seit dem Jahr 2010 virtuelles Testen für die Typzulassungsprüfung. Technische Details bzw. konkrete Prozeduren für spezifische Regelungen sind in dieser Verordnung jedoch nicht enthalten. Das Hauptziel des europäischen Projekts IMVITER (lmplementation of Virtual Testing in Safety Regulations) war es, basierend auf der neuen Verordnung ein virtuelles Testverfahren auszuarbeiten und dabei offene Fragen zu berücksichtigen. Um die im Projekt-Konsortium unter Berücksichtigung der Anliegen aller Interessensgruppen wie Autohersteller, Zulassungsbehörden und technischer Dienste erarbeiteten offenen Punkte zu adressieren, wurde ein generisches Flussdiagramm entwickelt, das den Ablauf einer virtuell basierten Typprüfung darstellt. ln diesem Diagramm ist der virtuelle Typgenehmigungsprozess in drei aufeinander folgende Phasen aufgeteilt, die Verifikations-, Validierungs- und Typgenehmigungsphase. Von entscheidender Bedeutung ist die Phase der Validierung des Simulationsmodells, für die im IMVITER-Projekt eine Methodik vorgeschlagen wurde. Mit der im Projekt vorgeschlagenen Validierungsmethode ist kein Austausch des Simulationsmodells zwischen Fahrzeughersteller und technischem Dienst notwendig, so dass die Vertraulichkeit von Betriebsgeheimnissen nicht gefährdet ist. Zur Validierung des Modells werden jedoch immer Versuche notwendig sein. Dies gilt sowohl für die Überpruefung von passiven als auch aktiven Fahrzeugsicherheitssystemen. Eine zusammenfassende Betrachtung der Erfahrungen aus dem IMVITER-Projekt ergab, dass mit der Einführung von virtuellem Testen keine Erhöhung der Anforderungen an die Fahrzeugsicherheit bzgl. bestehender Regelungen verbunden sein sollte. Jedoch werden auch weiterhin neue zusäztliche Regelungen erforderlich sein, da sich das Unfallgeschehen und die Fahrzeugtechnologie weiterentwickeln und ändern werden. Diese sollten von Beginn an die Möglichkeiten des virtuellen Testens nutzen, insbesondere bei Testverfahren für neue Technologien, z.B. aktiver Fahrzeugsicherheitssysteme. Hier bieten virtuelle Testverfahren nicht nur eine Kosten- oder Zeitersparnis, sondern ermöglichen teilweise erst die sinnvolle Abprüfung von neuen Sicherheitssystemen, die mit aktuellen auf Hardware-Test basierenden Verfahren überhaupt nicht möglich wären.
Das Fahrverhalten ändert sich mit zunehmendem Alter. Damit ändern sich auch die Risiken. Neben den jungen Fahranfängern im Alter von 18 bis etwa 25 Jahren stellen Fahrer über 75 Jahre eine besondere Problemgruppe dar. Mit zunehmender Zahl alter Fahrer (demographische Entwicklung plus Zunahme der Fahrerlaubnisinhaber in dieser Altersgruppe) besteht hier in naher Zukunft akuter Handlungsbedarf. Ansatzpunkte gibt es im gesamten Mensch-Maschine-Umwelt-System. Fahrzeuge müssen vermehrt im Hinblick auf alte Fahrer konstruiert und optimiert werden. Die Infrastruktur muss den Bedürfnissen einer eindeutigen Verkehrsführung angepasst werden. Aber nur, wenn der Mensch selbst geeignet ist, als Fahrer am Straßenverkehr teilzunehmen, ist ein Gewinn bei der Verkehrssicherheit zu erwarten. Dies muss gewährleistet werden. Wichtig ist, dass die Problematik der alten Fahrer als solche erkannt wird und schnell eine tragfähige Lösung für die Zukunft gefunden wird.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
The frontal crash is still an important contributor to deaths and serious injured resulting from road accidents in Europe. As the Hybrid-III dummy used in crash tests is over two decades old, the European Enhanced Vehicle-safety Committee is studying the potential for a new test device. Key is the availability of a well-defined set of requirements that identifies the minimum level of biofidelity required for an advanced frontal dummy. In this paper, a complete set of frontal impact biofidelity requirements, consisting of references , description of test conditions and corridors, is presented.