The increase in light duty trucks (LDT) on the road in the US is a safety concern because of their aggressivity, or risk they present to occupants of cars, especially in side impacts. We use FARS data to look at fatality trends in frontal and side impacts between cars and LDT. FARS data is also used to determine risk, or fatalities per registered vehicle, imposed on car drivers from other vehicle types. We use NASS CDS data to investigate sources of serious injuries in vehicles with side impact. These sources of injury are categorized into three major groups: 1) contact without intrusion, 2) contact with intrusion, and 3) restraints. We find a greater fraction of intrusion related injuries in cars struck on their side by SUV or pick-up trucks than when they are struck by other cars.
In spite of today's highly sophisticated crash test procedures like the different NCAP programs running world-wide, bad real world crash performance of cars is still an issue. There are crash situations which are not sufficiently represented by actual test configurations. This is especially true for car to car, as well as for car to object impacts. The paper describes reasons for this bad performance. The reasons are in principal bad structural interaction between the car and its impact partners (geometric incompatibility), unadjusted front end stiffness (stiffness incompatibility) and collapse of passenger compartments. To show the efficiency of improving cars' structural behaviour in accidents with different impact partners an accident data analysis has been taken out by members of European Project VC-COMPAT. Accident data analysis has shown that in Germany between 15,000 and 20,000 of the now severely injured car occupants might get less injured and between 600 and 900 car occupant fatalities might be saved. Similar results arise for the UK.
Today, Euro NCAP is a well established rating system for passive car safety. The significance of the ratings must however be evaluated by comparison with national accident data. For this purpose accidents with involvement of two passenger cars have been taken from the German National Road Accident Register (record years 1998 to 2004) to evaluate the results of the NCAP frontal impact test configuration. Injury data from both drivers involved in frontal car to car collisions have been sampled and have been compared, using a "Bradley Terry Model" which is well established in the area of paired comparisons. Confounders " like mass ratio of the cars involved, gender of the driver, etc. " have been accounted for in the statistical model. Applying the Bradley Terry Model to the national accident data the safety ranking from Euro NCAP has been validated (safety level: 1star <2 star <3 star <4 star). Significant safety differences are found between cars of the 1 and 2 star category as compared to cars of the 3 and 4 star category. The impact of the mass ratio was highly significant and most influential. Changing the mass ratio by an amount of 10% will raise the chance for the driver of the heavier car to get better off by about 18%. The impact of driver gender was again highly significant, showing a nearly 2 times lower injury risk for male drivers. With regard to the NCAP rating drivers of a high rated car are more than 2 times more probable (70% chance) to get off less injured in a frontal collision as compared to the driver of a low rated car.
In this study, the mean profile depth (MPD) that expresses roughness of road pavements was calculated using the road survey equipment vehicle and the calculated MPD was compared with the real number of traffic accidents. The analysis method used in this study was to classify the appropriate clustering in relation to traffic accidents using the K-means clustering and to compare this with the presence of traffic accidents via the MPDs to derive the result. K-means clustering was used in the analysis method and four clusters were found using the clustering analysis results. The center of each cluster was 0.627, 0.850, 1.118, and 1.237, respectively. The result of this study is expected to be utilized as foundational research in the traffic safety area.
The current paper reports on the results of a pilot study aiming to investigate the effect of mobile telephone use on the driving performance of 5 amateur and 5 professional drivers. Their driving acuity was tested through a driving simulator. Analysis and interpretation of the results occurred comparing the drivers' driving performance while talking, reading messages and writing a message on the mobile phone (intervention time) with the drivers' driving performance engaged in no activity (control time). The variables affected by the mobile phone were the "steering", the "lane offset" and the "duration of lane offset". Moreover, the drivers involved in a car crash in the last five years appeared to differ from those who were not involved in a crash in both "lane offset" and "following distance". The results of this pilot study will inform the design of a large experimental study on 50 professional and 50 amateur drivers.
During the last 5 years, the number of cars fitted with side airbags has dramatically increased. They are now standard equipment, even on many smaller cars or less luxurious vehicles. While some side airbags offer thoracic protection alone, there are those that combine thoracic and head protection (of which most deploy from the seat). Other systems employ separate airbags for head and thorax protection, which are designed to be effective noticeably in a crash against a pole. This paper proposes an evaluation of the effectiveness of side airbags in preventing thoracic injuries to passenger car occupants involved in side crashes. First, the target population (who can take benefit of side airbag deployment and in what circumstances) is defined. Side airbags can be especially effective in cases of impacts on the door with intrusion at a certain impact speed. Then, an example case of a side impact with side airbag deployment is given were side airbag deployment is thought to have had a positive effect on injury outcome. A further case is presented where the impact configuration is likely to have reduced the effect of side airbag deployment on injury outcome. Finally, the estimation of side airbag effectiveness (in terms of additional occupant protection brought exclusively by the airbag) is proposed by comparing injury risk sustained by occupants in (more or less) similar cars (fitted or non fitted with airbags) because, during these years, car structure, and side airbag conception have considerably evolved. In-depth accident data from France, the UK and Germany has been collected. Out of 2,035 side impact accident cases available in the databases, we selected 435 occupants of passenger cars (built from 1998 onwards) involved in an injury accident between year 1998 and year 2004 for EES (Energy Equivalent Speed) values between 20km/h and 50km/h. The occupants, belted or not, were sat on the struck side, whatever the obstacle and type of accidents (intersection, loss of control, etc.). For multiple impact crashes, the side impact is assumed to be the more severe one. Passenger cars were fitted with (96) or without (339) side airbags. Most of the potential risk explanatory variables were correctly and reliably reported in the databases (velocity " impact zone " impact angle " occupant characteristics, etc.). The analysis compared injury risks for different levels of EES and different types of side airbags. A logistic regression model was also computed with injury variables (such as thoracic AIS 2+ or AIS 3+) as the dependant variable and other variables (including airbag type and EES) as explanatory injury risk factors. Results revealed statistically non-significant reductions in thoracic AIS 2+ and AIS 3+ injury risk in side airbag equipped cars in the impact violence range selected (odds ratio between 0.84 and 0.98 depending on types of airbags). The results are discussed. The non-significance is assumed to be due to a low number of cases. Statistical analysis for head injuries was not possible due to the low number of accident cases with passenger cars fitted with head airbags in the databases. Moreover, the discrepancies between the data coming from different countries (especially calculation of EES) might have introduced instability in the analysis.
Electronic Stability Program (ESP) aims to prevent the lateral instability of a vehicle. Linked to the braking and powertrain systems, it prevents the car from running wide on a corner or the rear from sliding out. It also helps the driver control his trajectory, without replacing him, in the case of loss of control where the driver is performing an emergency manoeuvrer (confused and exaggerated steering wheel actions). A new ESP function optimizes ESP action in curves with hard under steering (situations in which the front wheels lose grip and the vehicle slides towards the outside of the curve). A complementary feature prevents the wheels from spinning when pulling away and accelerating. The name given to the ESP system varies according to the vehicle manufacturer, but other terms include: active stability control (ASC), automotive stability management system (ASMS), dynamic stability control (DSC), vehicle dynamic control (VDC), vehicle stability control (VSC) or electronic stability Control (ESC). This paper proposes an evaluation of the effectiveness of ESP in terms of reduction of injur accidents in France. The method consists of 3 steps: - The identification, in the French National injury accident census (Gendarmerie Nationale only), of accident-involved cars for which the determination of whether or not the car was fitted with ESP is possible. A sample of 1 356 cars involved in injury accidents occurred in 2000, 2001, 2002 and 2003 was then selected. But we had to restrict the analysis to only 588 Renault Lagunas. - The identification of accident situations for which we can determine whether or not ESP is pertinent (for example ESP is pertinent for loss of control accidents whilst it is not for cars pulling out of a junction). - The calculation, via a logistic regression, of the relative risk of being involved in an ESPpertinent accident for ESP equipped cars versus unequipped cars, divided by the relative risk of being involved in a non ESP-pertinent accident for ESP equipped cars versus unequipped cars. This relative risk is assumed to be the best estimator of ESP effectiveness. The arguments for such a method, effectiveness indicator and implicit hypothesis are presented and discussed in the paper. Based on a few assumptions, ESP is proved to be highly effective. Currently, the relative risk of being involved in an ESP pertinent accident for ESP-equipped cars is lower (-44%, although not statistically significant)rnthan for other cars.rn
The National Highways Development Project in India is aimed at upgrading over 12,000 km of national highways from 2-lane undivided roads to 4-lane divided roads. With nearly 40% of fatal crashes being reported on national highways, the effect of this project on road safety needs to be assessed. Researchers carried out on-site crash investigations and in-depth crash data collection for a period of 45 to 60 days on four 2-lane undivided highways and a 4-lane divided highway. Based on 76 crashes examined, researchers found a shift of crash pattern from head-on collisions on undivided 2- lane highways to front-rear collisions on divided 4-lane highways. This paper presents the methodology, analysis of crashes examined, and the critical safety problems identified for greater consideration in future highway development projects. This paper also highlights the need and significance of in-depth crash investigations to understand local traffic conditions and problems in India.
In India, heavy truck crashes on national highways account for a number of fatalities. But due to lack of in-depth crash data, detailed analysis is not possible to determine injury mechanisms, and to identify infrastructure, vehicle and human factors affecting these crashes. Over the past two years, researchers in India have established a crash investigation network, with the co-operation of the police and hospitals, to conduct crash investigations and in-depth crash data collection on national highways in the state of Tamil Nadu. This pioneering effort has resulted in the development of a heavy truck crash investigation methodology, the outcome of which is scientific and reliable crash data that has been able to provide good insight into truck crashes and their causes. This paper explains the need for truck crash investigations, the methodology, conclusions of the data analyzed up to date, and the need to focus on truck driver working conditions.
[Introduction:] A large number of road users involved in road traffic crashes recover from their injuries, but some of them never recover fully and suffer from some kind of permanent disability. In addition to loss of life or reduced quality of life, road accidents carry many and diverse consequences to the survivors such as legal implications, economic burden, job absences, need of care from a third person, home and vehicle adaptations as well as psychological consequences. Within an EU funded project MOVE/C4/SUB/2011-294/SI2.628846 (REHABIL AID) these consequences were analyzed more detailed.
In the context of the COST357 research project, the climatic conditions and requirements for protective helmets for motorcyclists have been examined. The extent to which these factors would influence motorbike handling and accidents in which motorcyclists are involved have also been examined. This project addresses how cognitive abilities of motorcyclists relate to helmet construction factors. In particular, the aspects of motorcycle driver helmets are to be parameterized in order that they may be used subsequently as a basis for future requirement profiles. The task of one working group of the COST357 project has been to analyse accident events and to identify helmet design issues which affect motorcycle drivers while wearing a helmet. This has been achieved by collating accident data across different countries recorded in the course of in-depth investigations at the site of accidents and by combining this with field studies of motorcyclists participating in traffic, but not involved in accidents. This paper presents the study methodology, database and first results of this international survey. The basis of the study has been a total of 424 interviews of motorcyclists and 134 motorcycle accidents, which were collected across Germany, Greece, Italy, Ireland, Portugal and Turkey and combined in a single database.
This paper describes the methodology of In-Depth Investigation in Germany on the example of GIDAS (German In-Depth Accident Study). Since 1999 in Germany a joint project between FAT (Forschungsvereinigung Automobiltechnik or Automotive Industry Research Association) and BASt (Bundesanstalt für Straßenwesen or the Federal Road Research Institute) is being carried out in Hannover and Dresden. The methodology of this project is based on a statistically orientated procedure of data sampling (sampling plan, weighting factors). The paper describes the possibilities of such in-depth investigation on the results of the offered title. The accident cases were collected randomly within GIDAS at Hannover. There are more cases existing from previous investigation started in 1985 under the same methodology. The portion of rollovers can be established at 3.7% of all accidents with casualties in the year 2000. For the study 434 cases of car accidents with rollovers are used for a detail comprehensive analysis. The accidents happened in the years 1994 to 2000 in the Hannover area. The injury distribution will report about 741 occupants with rollover accident event. The presented paper will give an overview of the accident situations following in rollover movements of cars. The distributions of injury frequencies, injury severity AIS for the whole body and for the body regions of occupants will be presented and compared to technical details like the impact speed and the deformation pattern. The speed of the car was determined at the point of rollover and on the point of accident initiency. The characteristics of the kinematics followed in a rollover movement are analyzed and the major defined types of rollover will be shown in the paper. The paper will describe the possibilities of In-Depth Investigation methods for the approach of finding countermeasures on the example of car accidents with rollover and explaining the biomechanics of injuries in rollover movements.
Nigeria ranks one of the highest countries in the world with the largest accident, especially when measured by whiplash associated disorders, whereas, traffic safety education rate, data and information been widely known as preventive indicators have been grossly neglected. In Nigeria, traffic safety enlightenment, awareness, political understanding and appreciation of the problem's magnitude are lacking. This study, therefore, seeks to understand and document the fact that accident causation factors in Nigeria relate more to the problem of development, poverty, knowledge and education as evidenced in most other developing countries. Among the primary accident causation factors on Nigerian roads are: - lack of a transportation system or multi-model integration - sub-standard and obsolete vehicles and road furniture - poor road maintenance, investment and engineering management - paucity of road users' and drivers' knowledge, skill, enlightenment and education of the road Use This paper submits that Nigeria being a developing nation requires purely primitive strategies being cost effective (health wise) than curative measures. It is in this light that an enduring, comprehensive and sustainable traffic safety educational programmes information base and data inventory, analysis and implementations form the focus of this study. This effort will provide basic guidelines framework and implementation procedure for a successful prevention of whiplash associated disorder resulting from road traffic crashes in Nigeria and other parts of the world.
Since the compulsory use of child restraints for children up to 5 years of age was introduced in 2000, restraint use among younger children has increased significantly. However, the observed rate of child restraint use plateaus at around 50%, and apparently little spillover effect has been found for older children who are not covered by the law. This report examines the restraint use patterns for children who were injured in cars in relation to driver and child passenger characteristics. Univariate and multivariate analyses were conducted to describe the association between the outcome measure (the proper use of restraints for children) and relevant variables. Better ways for parents and caregivers to improve the use of restraints for children are also discussed.
This report gives an overview of pedestrian accidents on Japanese roads. Database used for the analysis is national traffic accident data based on police reports. Relevant measures and background information ranging from vehicle safety, engineering and education are briefly reviewed, and area for further improvement is discussed.rn
Event data recorders (EDRs) are a valuable tool for in-depth investigation of traffic accidents. EDRs are installed on the airbag control module (ACM) to record vehicle and occupant information before, during, and after a crash event. This study evaluates EDR characteristics and aims at better understanding EDR performance for the improvement of accident reconstruction with more reliable and accurate information regarding accidents. The analysis is based on six crash tests with corresponding EDR datasets.
Twenty-eight percent of traffic accidents in Japan are rear-end collisions, and of these, 13% are multiple collisions (three or more vehicles and/or roadside objects). A post-crash braking system enables the driver to stop the vehicle in a short distance after a rear-end collision to prevent secondary collisions. In this study, the effectiveness of a post-crash braking system was examined using a drive recorder database. In 64% of rear-end collisions, the driver's braking was interrupted after the collision. The stopping distance was estimated with time data from the drive recorder. We predict that the brake assist would be effective in preventing secondary collisions in 21% of cases.
While accident statistics on a national level are provided by many countries, there is a need for international data that includes more detailed information about the accident, so called in-depth data. As a consequence, accident data projects have been emerging in different regions of the world. This creates a need for comparable and mergeable data from different countries, enabling the use of already existing accident data resources and helping to expedite the improvement of global road safety. While existing approaches focus that mostly on building a comprehensive accident database from scratch, the iGLAD project (Initiative for the Global Harmonization of Accident Data) attempts a more pragmatic approach by building on top of the work already accomplished in this area and complementing it. The target of iGLAD is to help setting up an additional dataset as a compatibility layer between already existing world wide data sets and integrating the structure of these by defining a common data scheme. This dataset is limited to the common denominator between the existing data sets and is inherently rather small and simple. Eventually, an individual converter for each participating accident investigation group will be built that enables pooling all data sets in a common repository. This not only saves costs and time, and hence makes such a target more feasible, but also creates data that is usable right from the start. This paper gives an overview of the current status of iGLAD and first steps taken. Additionally, some methodological aspects are discussed, next to a glance at other projects working currently on related issues, providing additional input for iGLAD. Finally, an overview of next steps and intended future work is given.
A lot of factors are related to a road traffic accident; particularly human factors such as road use characteristic, driving maneuver characteristic and safety attitude are the major ones. As a random factor is also included, so it is necessary to minimize the contribution of a random factor to identify human factors related to a road traffic accident. There are several standpoints for traffic accident analysis, such as vehicle-based, location-based and driver-based. And it is effective to analyze driver-based traffic accident data for discussion on the relation between human factors and accidents. An integrated traffic accident database system was developed for analysis considering driver- accident and violation records by ITARD, and several studies were carried out for the evaluation. Useful data for discussion on the relation between types of collision and traffic violations, and the effect of accident experience to the following accident were obtained.
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
The objective of the study is to measure the risk of pedestrian and bicyclist in urban traffic through an analysis of real-world accident data. The kinematics and injury mechanisms for both pedestrian and bicyclists are investigated to find the correlation of injury risks with injury related parameters. For this purpose, firstly 338 cases are selected as a sample from an IVAC accident database based on the In-depth Investigation of Vehicle Accident in Changsha of China. A statistic measurement of the fatality and serious injury risks with respect to impact speed was carried out by logistic regression analysis. Secondly, 12 pedestrian and 12 bicyclist accidents were further selected for reconstruction with MADYMO program. A comparative analysis was conducted based on the results from accident analysis and computer reconstructions for the injury risk, head impact conditions and dynamic response of pedestrians and bicyclists. The results indicate that bicyclists suffered lower risks of severe injuries and fatalities compared with pedestrians. The risks of AIS 3+ injury and fatality are 50% for pedestrians at impact speeds of 53.2 km/h and 63.3 km/h, respectively, while that for bicyclists at 62.5 km/h and 71.1 km/h, respectively. The findings could have a contribution to get a better understanding of pedestrians" and bicyclists" exposures in urban traffic in China, and provide background knowledge to generate strategies for pedestrian protection.
Vorgestellt werden Vorgehensweise, Datenaufbereitung, Modellaufbau und Ergebnisse des BASt-Projekts "Numerische Simulation der Stickoxidminderung durch photokatalytische Oberflächen an Verkehrswegen". Die Vorteile des Konzepts liegen in der Berücksichtigung von Zeitreihen (Eingangsdaten, Ausbreitungsrechnung) und in der Tatsache, dass die Depositionsgeschwindigkeit als zeitlich variable Eingangsgröße bei der Modellierung berücksichtigt wurde. Die Ergebnisse liegen entsprechend als Zeitreihen vor (Jahres- oder Tagesgänge können untersucht werden). Es ergab sich eine Minderung der NO2-Belastung um maximal knapp 1.5% im Nahbereich der Lärmschutzwand. Wesentlicher Faktor bei der Wirksamkeit photokatalytischer Oberflächen ist die Interaktion zwischen Gesamtbelastung und Depositionsgeschwindigkeit im Tagesverlauf.
Es wird über einen Kongress zur Gestaltung von Verkehrssicherheitskampagnen berichtet. Ziel dieses Kongresses war es, im europäischen Vergleich Stellenwert und Wirkung verschiedener Stilmittel und insbesondere die Vor- und Nachteile der Konfrontation als Instrument von Kampagnen herauszuarbeiten. Der Kongress bestätigte die verkehrspolitische These, dass es in der Verkehrssicherheitsarbeit keine für alle Staaten richtigen Konzepte für Erziehung und Aufklärung geben kann.
Das zweite Treffen der Koordinierungsstelle "Vernetzte Verkehrssicherheitsarbeit im Verkehrsverbund Rhein-Sieg" mit den örtlichen Kinderunfallkommissionen fand im September 2006 statt. Über 40 Teilnehmer vertraten die überwiegend aus Nordrhein-Westfalen kommenden Kommissionen. Schwerpunkt der Veranstaltung war das Thema "Schulweg- und Mobilitätspläne - Erfahrungen aus der Praxis". In drei Workshops wurden folgende Themen diskutiert: 1. Der Schulweg- und Mobilitätsplan als gemeinsame Aufgabe von Schule, Polizei, Gemeinde und Eltern; 2. Verkehrssicherheitsprobleme und wie man sie erkennen kann; 3. Gestaltungsmöglichkeiten der Pläne für Grund- und weiterführende Schulen und Überprüfung der Effektivität von Schulweg- und Mobilitätsplänen. In den Workshops berichteten Vertreter verschiedener Kinderunfallkommissionen über ihre Erfahrungen aus der Praxis bei der Erstellung der Pläne. Für die Verkehrssicherheitsanalyse verwiesen die Teilnehmer auf positive Erfahrungen mit der elektronischen Unfalltypensteckkarte. Die Erstellung von Schulweg- und Mobilitätsplänen könnte durch die Bereitstellung von Computerprogrammen sehr vereinfacht werden. Die Pläne selbst sollten in verschiedenen Formen zur Verfügung stehen: als Flyer, im Internet und als Poster. Die Abschlussdiskussion zeigte, dass bei der Erstellung von Schulweg- und Mobilitätsplänen noch viele Fragen zu klären sind. Zudem sollte grundsätzlich geklärt werden, welche Rahmenbedingungen geschaffen werden müssen, um die Arbeit der Kinderkommissionen zu fördern und zu unterstützen.
Angesprochen wurden aktuelle Entwicklungen beim Neubau und neue Entwicklungen bei Instandsetzungen und Verstärkungen. Eingegangen wird zu Beginn auf den Bestand an Brücken im Bundesfernstraßenbereich und auf die Entwicklung der Stahlpreise zwischen 2004 und 2008 mit einer sprunghaften Verdoppelung im August 2008 gegenüber den Jahren davor. Anschließend wird der Neubau von Stahlbrücken beleuchtet, auch mit Angabe der Möglichkeiten des Bundesministeriums fuer Verkehr, Bau und Stadtentwicklung (BMVBS) zur Förderung technischer Weiterentwicklungen und Innovationen. Aktuelle Entwicklungen bei Stahlverbundbrücken sind einteilige Überbauquerschnitte, VFT-Träger für Überführungen, luftdicht verschweisste Kästen, Hohlkästen mit Wellstahlträgern und Stahlrohrfachwerke. Alle diese Themen werden mit Beispielen unterlegt dargestellt. Neue Entwicklungen bei Instandsetzungen und Verstärkungen betreffen die verschiedenen Arten der Verstärkung von orthotropen Platten durch Aufkleben von Stahlplatten, Aufbringen einer Sandwichplatte (Sandwich-Plate-System (SPS)), Aufbetonieren einer dünnen Schicht aus ultrahochfestem Beton und Aufbringen eines steiferen Fahnbahnbelags.
NASS: the glass is half full
(2007)
The National Accident Sampling System (NASS) was born in the late 1970s. It was based on a substantial amount of experience and analysis of what was needed in the United States to understand the safety challenges of our highways. This work also showed how to collect high quality and useful crash data efficiently. Unfortunately, when Ronald Reagan - a President who believed in limited government - was elected, any hope of full funding for NASS was lost. The concept of 75 teams investigating about 18,000 serious crashes in detail annually was never realized. The system got up to 50 teams, then was cut to 36, and finally to 24 teams investigating fewer than a quarter of the originally anticipated number of crashes per year. Despite this, the NASS investigations provide a rich source of data, collected according to a sophisticated statistical sampling system to facilitate detailed national estimates of road casualties on our nation- highways and their causes. In addition, changes have been made in recent years to increase the number of more serious crashes of recent model vehicles to make the results more relevant to improving vehicle safety. A recent, detailed examination of hundreds of rollovers has provided considerable insight into rollover casualties and into what can be done to reduce them. Some of these results will be presented that show the value of the NASS system. Our experience with NASS and the Fatal Accident Reporting System (FARS) suggests a number of improvements that could be made in the United States" crash data systems. It also provides justification for a doubling or tripling of our national expenditures on crash data collection.
The misuse of CRS (child restraint system) is one of the most urgent problems in connection of child safety in cars. Numerous field studies show that more than two thirds of all CRS are used in a wrong way. This misuse could lead to serious injuries for the children. Surprisingly the quality of CRS use is coded much better in accident data (e.g. GIDAS) than the results of observatory field studies show. It is expected that misuse of CRS was not detected by the accident teams in a large number of the cases. An essential part in improving child seats and their usability is the knowledge of the relation between misuse and resulting injuries. For that the analysis and experimental reconstruction of accidents is an important part. For allowing an exact experimental accident reconstruction, it is necessary to have detailed information about the securing situation of the child and about the installation of the CRS in the car.
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
Introduction: Spine injuries pose a considerable risk to life and quality of life. The total number of road deaths in developed countries has markedly decreased, e.g. in Germany from over 20000 in 1970 to less than 4000 in 2010, but little is known how this is reflected in the burden of spine fractures of motor vehicle users. In this study, we aimed to show the actual incidence of spine injuries among drivers and front passengers and elucidate possible dependencies between crash mechanisms and types of injuries.
To elucidate the risk of pedestrians, bicycle and motorbike users, data of two accident research units from 1999 to 2014 were analysed in regard to demographic data, collision details, preclinical and clinical data using SPSS. 14.295 injured vulnerable road users were included. 92 out of 3610 pedestrians ("P", 2.5%), 90 out of 8307 bicyclists ("B", 1.1%) and 115 out of 4094 motorcycle users ("M", 2.8%) were diagnosed with spinal fractures. Thoracic fractures were most frequent ahead of lumbar and cervical fractures. Car collisions were most frequent mechanism (68, 62 and 36%). MAIS was 3.8, 2.8 and 3.2 for P, B and A with ISS 32, 16 and 23. AIS-head was 2.2, 1.3 and 1.5). Vulnerable road users are at significant risk for spine fractures. These are often associated with severe additional injuries, e.g. the head and a very high overall trauma severity (polytrauma).
Although ATV accidents account for numerous deaths in the US and Australia, the role in traffic accidents and hospital admissions in Germany is unknown. At a level I trauma centre, hospital and crash charts were analysed for medical and technical parameters of ATV accidents. ATV drivers were 0.1% of emergency trauma patients. The mean total hospital stayrnwas 15 days; there were 1.5 stays per patients with 2.0 surgical procedures needed. One patient died, only two recovered fully. 14 cases of ATV accidents out of 18990 (0.1%) were documented within 10 years. The mean impact velocity was 35 km/h. Car collisions were predominant. The upper extremity was the predominant injured region (AIS 0.7), Mean maximum AIS was 1.4. ATV accidents in Germany are rare but pose high risk for severe injuries. Possible reasons are low active and passive security, limited experience and risky driving behaviour. Preventive measures are discussed.rn
This study aims to analyze spine injuries in motor vehicle accidents. Between 1985 and 2004 the Hannover accident research unit documented 18353 accidents. We identified 161 front passengers (0.53%) with cervical spine injuries, 84 (0.28%) with thoracic and 95 (0.31%) with lumbar injuries. Technical and medical data was reviewed. Patients" records were retrieved. X-rays were evaluated and fractures were classified according to the Magerl classification. 68% and 57% of thoracic and lumbar fractures occurred in accidents with multiple impacts. Delta-v was 50, 40 and 40 kph in passengers with cervical, thoracic and lumbar spine, resp. Passengers with spinal fractures frequently showed numerous concomitant injuries, e.g. additional vertebral fractures. The influence of seat belts and airbags is discussed. Patient work-up has to include a thorough investigation for additional injuries.
The study aimed at estimating the impact of pedelecs (with an assumed higher speed than bicycles) on the traffic accident severity in Germany for different penetration rates. The analysis shows that in many real situations (68%) an electrical support of bicycles has no influence on the sequence of accident events. Taking into account a number of unreported "single bicycle accidents", the adoption of similar traffic behavior and similar age distribution, the authors determined a shift of 400 former slightly to seriously injured cyclists in Germany per year. Overall this would be an increase of approximately 2.3% in case of 10% of pedelec penetration with the pessimistic assumption of 10 km/h speed increase although first natural driving studies predict a much lower average speed increase of pedelecs. The hypothesis verbalized in the initial question whether a higher distribution of pedelecs will result in more severe accidents in Germany is not verified. The study shows that electrical support didn"t result in higher collision speed in general. In many accident situations, the speed of pedelecs has only a minor influence on the accident severity. Further research focusing on a possible change of driver behavior especially in new target groups (elderly people) will be needed.
Although road infrastructure is developed extensively Brazil is still one of the countries with the most dangerous roads in the world. In order to stop the increasing trend of traffic fatalities of the last few years and to improve traffic safety on Brazilian roads a pilot study on behalf of SAE Brazil started in March 2016 with the goal to lay the foundations for a long-term research activity. Piloting for an in-depth accident investigation the city of Campinas, roughly 100 km north of São Paulo was chosen. The pilot project was carried out with the local partner, the Empresa Municipal de Desenvolvimento de Campinas (EMDEC). The paper reports on the initial training of evidence based accident data collection on-spot, the implementation of the new digital database, the data collection and the first results. An outlook on the planned long-term accident investigations is given.
The increasing economics in India has an enormous growth of its road traffic. As observed from official Indian accident statistics the number of road fatalities are one of the highest worldwide. In contrast to most industrialized nations they have an rapidly increasing trend. To come along with this trend it becomes more than essential to understand the traffic accident situation. The official Indian accident statistics gives a glimpse of only basic information. Therefore more detailed data is needed. By using In-depth accident data and officially representative statistics the current accident situation can be evaluated in India, if a suitable weighting methodology is considered. Hence in 2009/2010 a pilot study with the collaboration partner JP-Research India pvt. Ldt. was gathered in Tamil Nadu in south of India. In-depth accident investigations were done around the Coimbatore area on four highways. At first, the collected data is evaluated. Due to consequent and continuous further development based on the first approach a methodology similar to NASS/CDS/GES in the US and GIDAS in Germany was developed. Of course all relevant accident related parameters including pictures and severity information were collected. As a matter of fact based on scaled sketches and reconstruction benefit analyses can be done in order to analyze the accident scenery in India. As a first outcome influence from infrastructure, missing education and vehicle safety were identified as key parameters in order to reduce the number of accidents and casualties. To compare the accident situation against international standards an accident classification for left hand traffic was developed based on the German Insurance classification system. Looking into detail additional accident types were identified and added to create an Indian accident type catalogue. The positive results encouraged several OEMs to participate in this investigation and together with BOSCH a consortium was established in 2010/11. Within one year from beginning in May 2011 about 200 highway accidents were collected, reported and reconstructed using the new standard. Hence a first good overview of the accident situation is available for the Coimbatore Tamil Nadu area. The major target for establishing accident investigations is the extension towards other states of India and urban areas to achieve a better overview of the accident scenery. Therefore local and national authorities have to be embedded in order to strengthen the awareness against traffic safety.
Ziel der Untersuchung war, die Frage zu klären, inwieweit die Verwendung von fluoridhaltigen Blutentnahmesystemen einen Vorteil in Begutachtungsfragen bei Cocain-Konsumenten bringen kann. In einigen Bundesländern werden diese Blutentnahmesysteme bereits seit Jahren angewendet, um einer Zersetzung von Cocain entgegenzuwirken (Inhibition der Esterasen im abgenommenen Blut). Entsprechende Empfehlungen finden sich auch in den Richtlinien der Gesellschaft für Toxikologische und Forensische Chemie (GTFCh). Bei der Verwendung Fluorid-stabilisierter Blutentnahmesysteme fanden sich in mehr als 50 Prozent der Fälle neben dem nicht aktiven Stoffwechselprodukt Benzoylecgonin (BE) auch Cocain (ein Beleg des zeitnahen Konsums) im Blut. Seit Mitte 2007 ist neben dem Stoffwechselprodukt BE auch die Muttersubstanz Cocain im Anhang zu Paragraf 24a Straßenverkehrsgesetz (StVG) aufgeführt. Aus forensisch-toxikologischer Sicht ist die Verwendung fluorid-stabilisierter Entnahmesysteme zwingend anzuraten, da nur dann ein Nachweis der aktiven Muttersubstanz Cocain selbst ermöglicht wird.
In der Akutphase eines Rausches durch Stimulanzien sind die erwünschten Wirkungen nicht zwingend mit einer Beeinträchtigung der Fahrsicherheit in Verbindung zu bringen. Eine gesteigerte physische Leistungsfähigkeit kann sogar zumindest kurzfristig mit einer Verbesserung der Fahrleistung einhergehen. Es sind eher die unerwünschten Akutwirkungen, insbesondere aber die Nachwirkungen eines Rausches, die Einfluss auf die Fahrsicherheit nehmen können. Ziel der Untersuchung war es, Konzentrationsbereiche und verkehrsmedizinisch relevante psychophysische Auffälligkeiten von Fahrzeuglenkern zusammenzuführen und zu überprüfen, in welcher Rauschphase eine Teilnahme am Straßenverkehr erfolgt ist beziehungsweise kritisch zu sein scheint. 8.824 Fälle, bei denen eine aktive Teilnahme am Straßenverkehr erfolgt war, wurden daraufhin untersucht. Im Vergleich zu anderen (zentral dämpfenden) Substanzklassen sind bei Amphetaminen weniger psychophysische Leistungsdefizite bei der Polizei und dem Blutentnahmearzt dokumentiert, allerdings werden Personen prinzipiell sowohl in der Akutphase als auch in der nachfolgenden Ermüdungsphase auffällig. Die Ergebnisse bestätigen, dass nach dem Konsum von Amphetaminen generell keine eindeutigen Konzentrations-Wirkungsbeziehungen zu beobachten sind.
Nowadays, traffic accidents are recorded in historical databases. Regarding the huge quantity of data, the use of data mining tools is essential to help Experts, for automatically extracting relevant information in order to establish and quantify relations between severity and potential factors of accidents. An innovative approach is here proposed for an in depth investigation of real world accidents data base. Mutual information ratio based on conditional entropies is used to quantity the association strength between an accident outcome descriptor (injury severity) and other potential association factors. Information theoretic methods help to select automatically groups of factors mostly responsible of the severity of accident.
A lack of representative European accident data to aid the development of safety policy, regulation and technological advancement is a major obstacle in the European Union. Data are needed to assess the performance of road and vehicle safety and is also needed to support the development of further actions by stakeholders. This short-paper describes the process of developing a data collection and analysis system designed to partly fill these gaps. A project team with members from 7 countries was set up to devise appropriate variable lists to collect fatal crash data under the following topic levels: accident, road environment, vehicle, and road user, using retrospective detailed police reports (n=1,300). The typical level of detail recorded was a minimum of 150 variables for each accident. The project will enable multidisciplinary information on the circumstances of fatal crashes to be interpreted to provide information on a range of causal factors and events surrounding the collisions.
The purpose of this work is to investigate the association between the injuries in motorcycle accident and the main accident configurations. The data were provided by a multicentric case-control study MAIDS regarding the risk of crash and injuries of motorcyclists. Chi-square test was used to evaluate the relationship between the variables and a logistic regression was performed to evaluate the association of injury severity with some variables supposed to be predictive factors. Lesive patterns characterized by internal haemorrhages are mainly associated with fronto-lateral crashes, above all in urban areas. Lacerations or abrasions, mainly reported in torso and lower extremities, are mostly associated with single crashes or accidents in queue also for crashes occurred to low speed (< 50 km/h). The severity of injuries is highly associated with impact speed, regardless of the crash configuration. Fractures and haemorrhages play an important role in determining the severity of injuries. The upper extremities are the most frequently traumatised anatomic areas.
Vehicle crash research at different levels is currently being conducted by several investigation groups in Spain, in some instances within various EU-funded projects. However there is a clear opportunity for increasing compatibility and maximizing usefulness, both at national and European levels, of the information collected by these groups. After reviewing on-going activities and programs in different countries, a framework for a nationwide crash investigation project is proposed: an organizational scheme is suggested as part of a future National Road Safety Strategic Plan; a map of investigation teams located in technological centres, universities and police agencies in Spain is presented; alternatives for several practical aspects such as team composition, deployment and operational budgets and project developmental stages are also discussed.
The Powered Two Wheelers (PTWs) accidents constitute one of the road safety targets in Europe. PTWs users' fatalities represent 15% of EU road fatalities, having increased the last few years, which is quite opposite than other road users casualties. To reduce PTW accidents is necessary to know which the accident causations are from different points of view (human factor, vehicle characteristics, environment, type of accident, situation, etc.). In TRACE project ("Traffic Accident Causation in Europe", under the European Commission 6th Framework Program, 2006-2008,) a specific task was focused on PTW users point of view, analyzing extensive databases to locate the main accident configurations (type of accident, severity, frequency), and an in-depth database to obtain the causation factors, the risk factors for each configuration founded in the extensive databases analysis and the variables associated to each causation factor in the PTW configurations.
The significant demographic changes are predicted for the European future. The age group over 65 years is permanently increasing and over next 30 years every fourth person will belong to this group. This development will continue so far that by 2050 in many countries will double the percentage of the population aged 65 and more. Many studies analyze the new phenomena of the ageing (graying) society during the last decade. Mobility is integrated part of the life of every citizen, even more it means for the elderly people. The adequate mobility is the precondition for their active life and for their social communication that contribute to their health and functional capacity and their autonomy and independency. The active seniors demand less public support. The mobility of the older citizens is closely linked with health and societal problems and creates an important public challenge. On the other side the participation of seniors in transport due to their limited physical and mental possibilities means for them an increased risk to be injured or killed. The main mobility spaces are roads that can be used not only as a traveler in a vehicle (driver or passenger) but also as a pedestrian or cyclist or even as a motorcyclist. The road traffic is then an opportunity and danger in the same time. The accident analyzes show specific risk features of seniors that are different compared with other age groups. First of all the older road users (65 and more) are facing to the higher risk (number of killed divided by the population size) to be killed in a road accident compared with the group of younger road users (0 - 64). More significant difference can be observed when comparing the road user groups. The fatality percentage of the older pedestrians is 2,5 times higher compared with the group 25 " 64. Similar frequency show the cyclist fatalities. On the other side the vehicle passengers in the younger group have more or less two time higher percentage compared to seniors and in the group of motorcyclists even achieved in 2008 almost five times higher compared with the older group. The share of the old road users fatalities (around 19%) didn"t practically change during the last 10 years in the European average. But comparing the gender involvement (2006) there is an interesting difference " female fatalities make 30, 2%, male fatalities 15, 3% of all fatalities in their groups. The risk of the senior users is more connected with their physical and mental limits than with their risk behavior. According to the Czech statistics (2007) the vehicle drivers over 65 years cause only 3, 6% of all accidents. The solution of the problem is to minimize the risk and to create a safe environment for the elderly people using the roads. In order to achieve this goal a deep knowledge of risk and of accident circumstances, full understanding of the behavior of the seniors and their limitations and accommodating approach of the whole society is necessary. Road risk of the ageing society has to be considered as a part of the health and social policy. These can build a creditable basis for the implementation of the measures that secure safe moving of seniors on the roads.
Having a look at safety to traffic and the prevention of accidents it can be observed that technical improvements in active safety of vehicles have let to various positive effects in this area. Among other components the tyre-road-contact takes a key role in the development of active safety technologies. All forces in accelerating, breaking and vehicle guidance have to be transmitted through the tyre-road contact area by friction forces. A common way to characterize a friction process is to identify the coefficient of friction μ between two touching materials. Even though there are several approaches to experimentially characterise road surfaces, no standard method exists. In this paper an overview of existing test methods is given. Furthermore the preliminary design of a newly developed portable test device with its possibility to investigate the tyre-road-friction of arbitrary roads or even places of accidents is shown.
From an automotive safety occupant protection standpoint, effective occupant restraint requires a system capable of providing non-injurious occupant ride down of anticipated crash forces. This is not only the case for frontal collisions, where occupant restraint is provided primarily by seatbelts and airbags, but is also critical for other crash modes such as side impacts, rear impacts, rollovers, as well as multiple impact events. In the rear impact crash mode, occupant restraint is provided primarily by the seatbacks and to some extent the seatbelts. Foundationally, therefore, what becomes fundamental to the seatback's role in rear occupant protection is its ability to contain the occupant within the seat, preventing occupant ramping, as well as preventing the seat's, and/or its occupant's, dangerous intrusion into the rear occupant's survival space where contact with rear compartment components and/ or rear seated occupants can present a significant injury risk. An analysis is presented of a series of rear impact sled testing conducted by the authors that evaluates the timing, position and extent of the front seatback's reward displacement toward and into the rear occupant compartment as well as consideration of the front seat occupant' ramping potential and its injury potential relative to the rear compartment. Additionally, three other series of testing are presented which assess various seat designs occupant retention capabilities. Lastly, a matched-pair comparison test series is presented which evaluates occupant motion in rear impact with and without use of a typical vehicle body mounted 3-point seatbelt. Discussion of restraint system performance observed in all the testing is included along with ATD biofidelity and thigh-gap considerations. The data collected and presented includes accelerometer instrumentation and high speed video analysis.
Automotive interiors have long been a potentially injurious impact area to occupants during accidents, especially in the absence of adequate padding. The U.S. Federal Motor Vehicle Safety Standard (FMVSS) 201, Occupant Protection in Interior Impact, outlines test procedures and performance criteria in order to mitigate potentially injurious head impacts to interior surfaces. FMVSS 201 specifies a finite set of impact locations and applies to passenger vehicles of a specified year range and with a gross vehicle weight rating less than 10,000 lb. In this paper, two head impact test methodologies are presented, a pendulum-test device and a Free Motion Headform (FMH) launching device, which allows for dynamic, repeatable impact evaluation of various vehicle interior surfaces and their impact attenuation abilities. The presented testing includes multiple series that evaluate the effect of differing vehicle upper interior padding on occupant head injury. One study in particular, analyzes a head impact to the side header of a heavy truck (not included in FMVSS 201) during a 90 degree rollover. Additionally, two other series of tests are presented which assess the injury reduction effect of side airbags to near side as well as far side occupants in a side impact scenario. Lastly, a forensic analysis is presented which evaluates two possible head impact locations experienced in a real world accident by analysis of the resulting interior compartment damage utilizing the FMH launching device test method. The data collected and presented includes accelerometer instrumentation and high speed video analysis. These studies demonstrate that adequate padding and airbags are very effective at mitigating head injury potential at impact speeds of 12-25 mph (19-40 kph).
Providing effective occupant protection in rollover crashes requires supplying the occupant with a restraint system proven effective in the dynamic rollover accident mode. Preventing ejection and providing restraint sufficient to prevent potentially injurious contacts with both interior and exterior vehicle components is paramount for effective rollover occupant protection. Research has shown that the injury potential can be decreased by closely coupling the occupant to the seat. This paper focuses on the effect of restraint system slack and its relationship to occupant excursion and ejection potential during rollover. Various restraint system configurations are evaluated in rollover-type test environments. A review of prior research is presented prior to presenting new quasi-static vehicle inversion studies conducted with live surrogate occupants. Additionally, dynamic rollover testing utilizing anthropometric test devices (ATDs) is presented. The influence of belt looseness and effects of various restraint designs on the belted occupants' injury potential are discussed.
Die Unfallzahlen für das Jahr 2008 zeigen, dass die intensiven Anstrengungen für die Verkehrssicherheit weiterhin Früchte tragen. Nachdem im Jahr 2007 mit 220 Toten auch in Rheinland-Pfalz der geringste Stand seit Einführung der Unfallstatistik registriert wurde, konnte dieser Trend auch im Jahr 2008 bestätigt werden. Die Verkehrssicherheitsarbeit in Rheinland-Pfalz sieht sich dabei zunächst im Kontext des anspruchsvollen Ziels der EU, die Zahl der Verkehrstoten bis 2010 zu halbieren. Im Mittelpunkt steht dabei die Frage, wie die Risiken im Verkehrsverhalten der Menschen minimiert werden können. Vorhandene Sicherheitspotenziale sollen genutzt werden, Maßnahmen sind gezielt auf die Brennpunkte im Verkehrsgeschehen auszurichten. Neben Sicherheitsaktionen und Trainings für die Verkehrsteilnehmer sowie der Polizeiarbeit ist einer der wichtigsten Ansätze die Verbesserung der Infrastruktur. Zu den Maßnahmen auf diesem Gebiet zählen neue Ansätze beispielsweise bei der Überprüfung sicherheitsrelevanter Aspekte schon in der Planung, beim Bau moderner Verkehrsbeeinflussungsanlagen oder bei der Sicherheit an Bahnübergängen und in Tunnels. Ein Fokus liegt jedoch auf der Unfallkommissionsarbeit. Sie ist ein wesentlicher Bestandteil der Gesamtkonzeption zur Verbesserung der Verkehrssicherheit. Das Land Rheinland-Pfalz verfügt seit nunmehr über 35 Jahren über institutionalisierte Erfahrungen auf diesem Gebiet, die auch als Beispiel für die bundesweite Entwicklung dienten. In einem weiteren Schritt werden seit kurzem in einer landesweiten Unfallkonferenz nunmehr Programmschwerpunkte wie beispielsweise die Bekämpfung von Motorradunfällen oder Baumunfällen definiert. Zudem wurden mit einem aufwändigen Programm allen der etwa 400 Unfallkommissionsmitglieder in Rheinland-Pfalz Schulungen angeboten. Eine permanente Nachschulung garantiert dabei einen gleichbleibend hohen Wissensstand. Beispielgebend ist allerdings auch die zentrale Unfallauswertestelle beim Landesbetrieb Mobilität in Koblenz, die es in dieser Form so nur noch in Bayern gibt. Mit ihr steht seit vielen Jahren ein Instrument zur Verfügung, das nicht nur die Grundlagen für gezielte und effektive Verkehrssicherheitsmaßnahmen schafft, sondern auch landesweite Controllings durchführt. Ohne eine finanzielle Ausstattung ist jedoch eine effektive Unfallkommissionsarbeit nicht möglich. Aus diesem Grund wurde als Novum ein spezieller Haushaltsansatz geschaffen, der gezielt ausschließlich im Sinne der Verkehrssicherheit - derzeit mit dem Schwerpunkt Baumunfälle und Motorradsicherheit - eingesetzt wird. Dabei wurde auch in einem Bewertungsverfahren zum Ausbauplan für Landesstraßen die Verkehrssicherheit so gewichtet, dass speziell Unfallhäufungsstellen in die Prioritätenreihung gelangen. Diese Ansätze mit Strategien aus einer Landesunfallkonferenz, gezielter Schulung, finanzieller Ausstattung sowie Unterstützung und Controlling durch eine zentrale Unfallauswertestelle sind zugleich Chance und Herausforderung für eine künftige Verkehrssicherheitsarbeit.
Der Beitrag befasst sich vor dem Hintergrund der kontrovers diskutierten Zwischenhaftung bei der Ausführung von Korrosionsschutzsystemen fuer Stahl- und Stahlverbundbrücken mit einer Abfrage bei den Bundesländern zu Schäden am Korrosionschutz bei Systemen nach Blatt 87 und Blatt 94 der ZTV-ING, Teil 4, Abschnitt 3. Auslöser für die Abfrage waren Schadensfälle mit grossflächigen Ablösungen der Deckbeschichtung aus Polyurethan, die nach einer Zwischenreinigung auf die Werksbeschichtung aus Epoxidharz aufgebracht worden war. Der Zeitraum zwischen der Beschichtung im Werk und dem Aufbringen der Deckbeschichtung auf der Baustelle kann zwischen einigen Wochen oder Monaten bis - in Ausnahmefällen - zu mehreren Jahren liegen. Mit der Abfrage bei den Straßenbauverwaltungen der Bundesländer sollte herausgefunden werden, ob Schäden aufgetreten sind - und wenn ja - in welchem Umfang. In die Umfrage einbezogen sind die 16 Obersten Straßenbauverwaltungen sowie die DEGES. Gemeldet wurden insgesamt 648 Stahl- und Stahlverbundbrücken, davon 46 mit Schäden am Korrosionsschutz. Die Schadensquote liegt demnach bei 7 Prozent. Es zeigte sich, dass die Enthaftung der Deckbeschichtung unterschiedliche Ursachen haben kann, insbesondere Nichteinhaltung des Sicherheitsabstands zwischen Objekt- und Taupunkttemperatur und unzureichende Reinigung der Zwischenbeschichtung. Ein grundlegendes, systembedingtes Zwischenhaftungsproblem kann nach den bisherigen Umfrageergebnissen nicht bestätigt werden. Sehr wohl sollte jedoch wegen der Schadensquote von 7 Prozent den Ursachen der aufgetretenen Schäden weiter nachgegangen werden.
The following paper presents the nature and mechanism of injuries sustained in frontal impacts, focusing on car to car impacts. It was found that the body regions most frequently sustaining severe to fatal injuries were the legs and the thorax. The nature and mechanism of the injury sustained was investigated only for the thorax injuries, due to their potentially life threatening nature. The analysis revealed that the most frequent cause of the injury recorded was the seatbelt for low severity injuries and the front structure of the vehicle for higher severity injuries. An analysis of the effect of load limiter technology in the restraint system showed that the proportion of occupants who sustained "no thorax injury" did not increase when a load limiter was fitted to the restraint system. However, a decrease in the "organ" and "organ and skeletal" injuries was observed in the load limiter sample. Sample size and variation mean that these findings are not conclusive.
Motorcycle riders are one of the most vulnerable road users. Annually, on estimate 6000 people are killed in motorcycle accidents in the former 15 EU countries. The objective of this research was to investigate and analyze the main aspects and causes of this vulnerability and the accidents in general. For this aim around 70 accidents in The Netherlands were investigated in the framework of an international research program (MAIDS). Also a control group of motorcycles with riders was investigated so that exposure could be taken into account. An important result is that human failure is in 82% of the cases the main cause of the accident, in 52% this is due the other vehicle driver. Perception and decision failures are the most common failures. The most injuries are caused by the environment but they are typically only less severe (AIS1). Injuries caused by the car (front and side) are typically severe injuries (AIS4+). Previous convictions of the MC rider seem to be related to the chance to get involved in an accident. It was shown that the Dutch and the total MAIDS accident sample are comparable.
While many medical studies have dealt with the incidence, nature and treatment of polytrauma the injury-causing accident mechanisms are rarely discussed in detail, mostly due to the lack of documentation of the technical aspects. The present prospective study was started in late 2007 and collects data from traffic accidents with most severely injured in six south- German counties and two larger cities for the duration of one year. It is aimed at identifying and documenting all polytrauma cases (ISS ≥ 16) caused by traffic accidents and their crash circumstances. The data collection is based on an interdisciplinary concept to include both the police, emergency dispatch centers, hospitals and fire departments in the region and is completely anonymous. Potentially relevant cases where an emergency physician was called to the scene of a traffic accident are provided by the dispatch center. All three hospitals in the region suited for the treatment of polytraumatised patients record injuries, major diagnostic and surgery data. Data and images from the accident scene are provided by the police and by fire departments. The latter provide information which is usually not available from the police, like deployed airbags, vehicle extrication measures and detailed views of car interiors. The main objective of the study is to determine the structure of road users who sustain a polytrauma, their crash opponents and the injury patterns found in relation to the collision configuration and the protection by seat belts, air bags and other devices. With detailed documentation of vehicle damage and extrication measures the study is also intended to support the development of injury predictors for pre-hospital treatment and provide field data regarding further improvement of technical rescue.
A total survey of road traffic accidents involving most severely injured, defined as sustaining a polytrauma or severe monotrauma (ISS > 15) or being killed, was conducted over 14 months in a large study region in Germany. Data on injuries, pre-clinical and clinical care, crash circumstances and vehicle damage were obtained both prospectively and retrospectively from trauma centers, dispatch centers, police and fire departments. 149 patients with a polytrauma and eight with a severe monotrauma were recorded altogether. 22 patients died in hospital. Another 76 victims had deceased at the accident scene. In 2008, 49 % of patients treated with life-threatening injuries were car or van occupants, 21 % motorcyclists, 18 % cyclists and 10 % pedestrians. Among fatalities at the scene, vehicle occupants constituted an even larger portion. The number of road users with life-threatening trauma in the region was extrapolated to the German situation. It suggests that 10 % among the "seriously injured" as defined in national accident statistics are surviving accident victims with a polytrauma or severe monotrauma.
Pelvic fracture, cracking or breaking of a portion of the pelvis are extremely common injuries in the side impact collisions of motor vehicles. Due to both its shape and structural architecture, mechanics of the pelvic bone is complicated. There is a lack of knowledge regarding the dynamic behavior of the pelvis and its biomechanical tolerance under impact environment. Hence this study is aimed at the understanding of the mechanical response of the human pelvis with three-dimensional finite element (FE) models, under side impact load, applied through a structure, equivalent to a car door. The door structure was modeled, considering few layers, consisting of foam (Styrodur®, 3035 CS), plastic (UHMWPE), steel, glass and steel, putting them in series. A soft tissue layer (equivalent to fat) was also considered on the greater trochanter location. These FE models (with and without the car door structure) were analyzed with ANSYS-LS-DYNA-® dynamic finite element software to compare the effect of the car door padding system for shock absorption. It was observed that with proper combination of shock absorbing material (foam, etc.) and its thickness, the transmission of impact load to the body part (pelvis, etc.) from the outer surface of the car door could be reduced.
This paper reviews briefly the evolution of the investigation of transport accidents from the early beginnings when individual events were studied but systematic data was not collected. In the transport modes other than on the roads, accident investigation early on, even of single events, was important in introducing safety improvements. Road accidents, however, evolved enormously with the growth of car ownership without any comparable political response to the consequent deaths and injuries, equivalent to what happened with the other modes. From the 1950s data bases started to contribute to our knowledge of the epidemiology of road traffic injuries, and in-depth sample studies have contributed much to the body of knowledge in the last 30 years. However, even the basic input and output variables of a crash, its severity and the seriousness of the outcomes in terms of injuries and their consequences are not complete or agreed upon. Issues of experimental design and sampling are discussed. It is proposed that the most important area for current research to address is the effect of population variations on injury outcomes. The need for the establishment of good data bases for active safety issues is emphasised with the consequent need for better links between the research community and the police.
Verkehrspsychologische Nachschulungen stellen Maßnahmen zur Rehabilitierung von im Straßenverkehr auffälligen Kraftfahrerlnnen dar. Diese gesetzlich verankerten psychologischen lnterventionsprogramme werden mit hohem Aufwand konzipiert und sind bei der täglichen Durchführung mit beträchtlichen Kosten verbunden. Daraus ergibt sich die Notwendigkeit, die Effektivität der Nachschulungsmodelle durch eine wissenschaftliche Evaluation zu klären. Um die Effektivität der Nachschulungskurse der AAP (Austrian Applied Psychology) zu überprüfen wurde eine Fragebogenstudie mit Pre-Posttest-Designs durchgeführt. Die Ergebnisse der Alkoholkurse zeigen positive Auswirkungen hinsichtlich Einstellungsänderung, spezifischer Selbstwirksamkeitserwartung, interner Attributionen, Wissen und Gesamtbeurteilung.
Im Jahr 2005 wurde mit dem Bau der Niederrheinbrücke Wesel der Bau der Ortsumgehung Wesel begonnen. Der Beitrag berichtet über einige Ausführungsdetails der im Jahr 2009 fertiggestellten Baumaßnahme: die Herstellung des Pylons in hochfestem Beton, die Montage der Strombrücke, der Einsatz von Parallellitzenbündeln.
This study aimed at developing an injury estimation algorithm for AACN technologies for Germany and compared them to findings based on Japanese data. The data to build and to verify the algorithm was obtained from the German in-depth Accident Database (GIDAS) and split into a training and a validation dataset. Significant input variables and the generalized linear regression model to predict severe injuries (ISS>15) were selected to maximize area under the receiver operating characteristic curve (AUC). Probit regression with the input parameter multiple impact, delta v, seatbelt use and impact direction gave the largest AUC of 0.91. Sensitivity of the algorithm was validated at 90% and specificity at 76% for an injury risk threshold of 2%. It appears that no major differences between Japan and Germany exist for injury estimation based on delta v and impact direction. However, far side impact and multiple crash events appear to be associated with a larger risk increase in the German data.
Das Bundesministerium für Forschung und Technologie finanziert das Projekt "Leistra2", welches zum Ziel hat, den Reifen-Fahrbahn-Kontakt zu untersuchen und Maßnahmen zu entwickeln, die den Verkehrslärm reduzieren, insbesondere das Reifen-Fahrbahn-Geräusch. Das Projekt besteht aus drei Arbeitsgebieten: leise Reifen, leise Fahrbahnbeläge und die Verifizierung der Ergebnisse. Jedes Arbeitsgebiet gliedert sich in mehrere Unterprojekte. Dieser Vortrag gibt einen Überblick über Leistra2 und berichtet über neueste Tätigkeiten und Ergebnisse. Weitergehende Information und die Kontaktdaten der beteiligten Partner finden sich unter http:// www. LeiStra2. de . Das Programm ist Nachfolger des Programmes LeiStra (Leiser Straßenverkehr), welches ähnliche Themenschwerpunkte behandelte.
The German Federal Ministry of Economics and Technology is funding a projectrncalled "Leistra2" with the aim of understanding the tire road contact and to find measures to reduce traffic noise, in particular to reduce the noise of tires rolling on pavements, i.e. tire-road noise. The project is composed out of three mayor subjects, low noise tires, low noise pavements and verification of the results, each made out of single sub-projects. The purpose of this paper is to give a survey about Leistra2 and to report about the latest activities and results. More detailed information and contact data of the partners involved can be found at http://www. LeiStra2.de. The program is the successor of the program LeiStra (Leiser Strassenverkehr), dealing with similar topics.rn
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
Causation patterns and data collection blind spots for fatal intersection accidents in Norway
(2010)
Norwegian fatal intersection accidents from the years 2005-2007 were analysed to identify any causation patterns among their underlying contributing factors, and also to evaluate whether the data collection and documentation procedures used by the Norwegian in-depth investigation teams produces the information necessary to perform causation pattern analysis. A total of 28 fatal accidents were analysed. Details on crash contributing factors for each driver in each crash were first coded using the Driving Reliability and Error Analysis Method (DREAM), and then aggregated based on whether the driver was going straight or turning. Analysis results indicate that turning drivers to a large extent are faced with perception difficulties and unexpected behaviour from the primary conflict vehicle, while at the same time trying to negotiate a demanding traffic situation. Drivers going straight on the other hand have less perception difficulties. Instead, their main problem is that they largely expect turning drivers to yield. When this assumption is violated, they are either slow to react or do not react at all. Contributing factors often pointed to in literature, e.g. high speed, drugs and/or alcohol and inadequate driver training, played a role in 12 of 28 accidents. While this confirms their prevalence, it also indicates that most drivers end up in these situations due to combinations of less auspicious contributing factors. In terms of data collection and documentation, information on blunt end factors (those more distant in time/space, yet important for the development of events) was more limited than information on sharp end factors (those close in time/space to the crash). A possible explanation is that analysts may view some blunt end factors as event circumstances rather than contributing factors in themselves, and therefore do not report them. There was also an asymmetry in terms of reported obstructions to view due to signposts and vegetation. While frequently reported as contributing for turning drivers, they were rarely reported as contributing for their counterparts in the same accidents. This probably reflects an involuntary focus of the analyst on identifying contributing factors for the driver legally held liable, while less attention is paid to the driver judged not at fault. Since who to blame often is irrelevant from a countermeasure development point of view, this underlying investigator mindset needs addressing to avoid future bias in crash investigation reports.
Accident data shows that the vast majority of pedestrian accidents involve a passenger car. A refined method for estimating the potential effectiveness of a technology designed to support the car driver in mitigating or avoiding pedestrian accidents is presented. The basis of the benefit prediction method consists of accident scenario information for pedestrian-passenger car accidents from GIDAS, including vehicle and pedestrian velocities. These real world pedestrian accidents were first reconstructed and the system effectiveness was determined by comparing injury outcome with and without the functionality enabled for each accident. The predictions from Volvo Cars" general Benefit Estimation Model are refined by including the actual system algorithm and sensing models for a relevant car in the simulation environment. The feasibility of the method is proven by a case study on a authentic technology; the Auto Brake functionality in Collision Warning with Full Auto Brake and Pedestrian Detection (CWAB-PD). Assuming the system is adopted by all vehicles, the Case Study indicates a 24% reduction in pedestrian fatalities for crashes where the pedestrians were struck by the front of a passenger car.
Injury probability functions for pedestrians and bicyclists based on real-world accident data
(2017)
The paper is focusing on the modelling of injury severity probabilities, often called as Injury Risk Functions (IRF). These are mathematical functions describing the probability for a defined population and for possible explanatory factors (variables) to sustain a certain injury severity. Injury risk functions are becoming more and more important as basis for the assessment of automotive safety systems. They contribute to the understanding of injury mechanisms, (prospective) evaluation of safety systems and definition of protection criteria or are used within regulation and/or consumer ratings. In all cases, knowledge about the correlation between mechanical behavior and injury severity is needed. IRFs are often based on biomechanical data. This paper is focusing on the derivation of injury probability models from real world accident data of the GIDAS database (German In-depth Accident Study). In contrast to most academic terms there is no explicit term definition or definition of creation processes existing for injury probability models based on empirical data. Different approaches are existing for such kind of models in the field of accident research. There is a need for harmonization in terms of the used methods and data as well as the handling with the existing challenges. These are preparation of the dataset, model assumptions, censored/unknown data, evaluation of model accuracy, definition of dependent and independent variable, and others. In the presented study, several empirical, statistical and phenomenological approaches were analyzed regarding their advantages and disadvantages and also their applicability. Furthermore, the identification of appropriate prediction parameters for the injury severity of pedestrians has been considered. Due to its main effect on injuries of pedestrians and bicyclists, the importance of the secondary impact has also been analyzed. Finally, the model accuracy, evaluated by several criteria, is the rating factor that gives the quality and reliability for application of the resulting models. After the investigation and evaluation of statistical approaches one method was chosen and appropriate prediction variables were examined. Finally, all findings were summarized and injury risk functions for pedestrians in real world accidents were created. Additionally, the paper gives instructions for the interpretation and usage of such functions. The presented results include IRFs for several injury severity levels and age groups. The presented models are based on a high amount of real world accidents and describe very well the injury severity probability of pedestrians and bicyclists in frontal collisions with current vehicles. The functions can serve as basis for the evaluation of effectiveness of systems like Pedestrian-AEB or Bicycle-AEB.
The evaluation of the expected benefit of active safety systems or even ideas of future systems is challenging because this has to be done prospectively. Beside acceptance, the predicted real-world benefit of active safety systems is one of the most important and interesting measures. Therefore, appropriate methods should be used that meet the requirements concerning representativeness, robustness and accuracy. The paper presents the development of a methodology for the assessment of current and future vehicle safety systems. The variety of systems requires several tools and methods and thus, a common tool box was created. This toolbox consists of different levels, regarding different aspects like data sources, scenarios, representativeness, measures like pre-crash-simulations, automated crash computation, single-case-analyses or driving simulator studies. Finally, the benefit of the system(s) is calculated, e.g. by using injury risk functions; giving the number of avoided/mitigated accidents, the reduction of injured or killed persons or the decrease of economic costs.
The grip between the road surface and vehicle tires is the physical basis for the moving of all vehicles in road traffic. In case of an accident the available grip level is one of the most relevant influence factors, influencing the causation and the procedure of the accident. However, the estimation of the grip level is not easy and therefore, is commonly not done on the accident scene. This is especially true for the measurement of the water depth. Until now, real accident databases provide no measurement data about the grip level and the water film depth and thus, the estimation of its influence is not possible yet. From the tyre manufacturers point of view, it is important to know about the road conditions (namely grip level, macro-texture, water depth, temperature) at the accident scene, as well as the operating conditions of the vehicles (braking, loss of control, speed, etc). These data is necessary to define relevant tyre traction tests for the end-user and for regulations. For this reason VUFO and Michelin developed a consistent method for the measurements of grip level and water depth for the accidents of the GIDAS database. The accident research team of Dresden, which documents about 1000 accidents with at least one injured person every year, is measuring the micro-roughness and the macro-roughness directly on the spot. For the measurement of the micro-roughness a Skid Resistance Tester (British Pendulum) is used. The Mean Texture Depth (describing the macro-roughness) is measured by the Sand Depth Method. Since June 2009, measurements for more than 700 accidents including 1200 participants have been carried out. In case of wet or damp road conditions during the accident, the water depth is measured additionally. Therefore VUFO and Michelin developed a special measurement device, which allows measurements with an accuracy of 1/10 millimetre. The measurement point at the accident scene is clearly defined and thus, the results are comparable for all different accidents and participants. The use of the GIDAS database and the accident sampling plan allows representative statements for the German accident scenario. With this data it is possible for the first time to have an accurate view of the road conditions at the accident scene. One possibility is a more detailed estimation of hydroplaning accidents using the actually measured water depths. The development of new testing methods and new tires can be based on the real situation of the road infrastructure. Furthermore, the combination of the technical GIDAS data and the measured road surface properties can also be used for the estimation of effectiveness of several safety systems like the brake assist and/or emergency braking systems. The calculation of a reduced collision speed due to the use of a brake assist is only one example for the application of real measured grip level data.
Analysis of the accident scenario of powered two-wheelers on the basis of real-world accidents
(2013)
For the first time since 20 years the German national statistics of traffic accidents revealed an increasing number of fatalities and seriously injured persons in 2011. This negative development was especially caused by increasing numbers in all groups of vulnerable road users (VRU). Furthermore, the comparison of fatality reduction rates between several categories of road users shows that persons on motorcycles show the worst performance over years. Although every second fatality in German traffic accidents is still a car occupant, users of PTW make up more than 20% in the meantime. Assuming further improvements in the field of occupant protection this trend will continue. For that reason, a study on the basis of real-world accidents was conducted to describe the accident scenario involving motorcycles and to identify the reasons of the above-described fact. Approximately 1.800 motorcycle accidents out of GIDAS database were used for the analyses. The first part of the study deals with the question how representative the GIDAS database is for the German motorcycle accident scenario. Afterwards, detailed descriptive statistics on motorcycle accidents were presented considering numerous parameters about the accident scene, environmental influences, vehicle information, individual characteristics, interview data, injury severity and injury causation. One important point is the identification of the most frequent critical situations that are typical for motorcycle accidents. Furthermore, a special focus was on accident causation. Finally, conspicuous facts out of the analysis are emphasized. All in all, the study gives a comprehensive overview about the German motorcycle accident scenario. One the one hand, the use of weighted GIDAS data allows representative and robust statements on the basis of large case numbers; on the other hand highly detailed conclusions can be drawn. The results of the study help to understand the particularities of motorcycle accidents and provide approaches for further improvements in the field of PTW safety.
The paper presents a methodology for the benefit estimation of several secondary safety systems for pedestrians, using the exceptional data depth of GIDAS. A total of 667 frontal pedestrian accidents up to 40kph and more than 500 AIS2+ injuries have been considered. In addition to the severity, affected body region, exact impact point on the vehicle, and the causing part of every injury, the related Euro NCAP test zone was determined. One results of the study is a detailed impact distribution for AIS2+ injuries across the vehicle front. It can be stated, how often a test zone or vehicle part is hit by pedestrians in frontal accidents and which role the ground impact plays. Basing on that, different secondary safety measures can be evaluated by an injury shift method concerning their real world effectiveness. As an example, measures concerning the Euro NCAP pedestrian rating tests have been evaluated. It was analysed which Euro NCAP test zones are the most effective ones. In addition, real test results have been evaluated. Using the presented methodology, other secondary safety like the active bonnet (pop-up bonnet) or a pedestrian airbag measures can be evaluated.
The declining trend since 1991 in the number of killed people was broken in 2011 when overall 4 009 people died in traffic accidents in Germany. The question arises if there is a stagnating trend of fatalities in Germany in future? By breaking down the accidents with casualties towards a monthly view one can see a decreasing trend of fatalities in the warmer months especially since 2009. When comparing against winter months higher deviations are observed. In December 2011 an increase of 191 traffic deaths were registered (181 in 2010 compared to 372 in 2011). Further analyses of different accident influences were evaluated and their possibility of drastic change from one year to the other was determined. As seen weather- and environmental conditions are one of the major contributing factors and are one of the causes for the increased number of fatalities. To support the underlying assumption a model had been created to calculate the number of traffic deaths on a daily basis approach. As an input, road conditions projected through weather parameters and also different driving behaviors on weekdays or holidays were used. As a result, estimates of daily fatality with up to 75% precision can be achieved out of the 2009, 2010 and 2011 data. Further on it shows that weather and street conditions have a high influence on the overall resulting number of traffic accidents with casualties, and especially to the number of fatalities. Hence it is estimated that approximately 3 300 people were killed in traffic accidents in Germany in 2013 which would be again a reduction of another 13% compared to 2012. Therefore an answer to the question will be that the decreasing trend in traffic fatalities in Germany somehow is not broken when environmental conditions are included in national statistics. Their effects will become more visible in future accident statistics and it is estimated variances of 5% to 8% of the annual number of traffic fatalities in Germany will be seen.
The paper aims to study the injury risk and kinematics of pedestrians involved in different passenger vehicle collisions. Furthermore, the difference of pedestrian kinematics in the accidents involved minivan and sedan was analyzed. The 18 sample cases of passenger car to pedestrian collisions were selected from the database of In-depth Investigation of Vehicle Accident in Changsha of China (IVAC),of which the 12 pedestrian accidents involved in a minivan impact for each case, and the 6 accidents in a sedan impact for each. The selected cases were reconstructed by using mathematical models of pedestrians and accident vehicles in a multi-body dynamic code MADYMO environment. The logistic regression models of the risks for pedestrian AIS 3+ injuries and fatalities were developed in terms of vehicle impact speed by analyzing the minivan-pedestrian and sedan-pedestrian accidents. The difference of pedestrian kinematics was identified by comparing the results from reconstructed pedestrian accidents between the minivans and sedans collisions. The result shows that there is a significant correlation among the impact speed and the severity of pedestrian injuries. The minivan poses greater risk to pedestrian than sedan at the same impact speed. The kinematics of pedestrian was greatly influenced by vehicle front shape.
Topics of this report are: Road construction (highways, interstate roads, urban by-passes, cycle tracks, construction sites, level crossings removal), traffic management systems, road tunnel equipment, harmonisation of vehicle regulations, accident statistics and accident research, passive vehicle safety, active vehicle safety , automotive environmental protection and rescue systems.
Annually within the European Union, there are over 50,000 road accident fatalities and 2 million other casualties, of which the majority are either the occupants of cars or other road users in collision with a car. The European Commission now has competency for vehicle-based injury countermeasures through the Whole Vehicle Type Approval system. As a result, the Commission has recognised that casualty reduction strategies must be based on a full understanding of the real-world need under European conditions and that the effectiveness of vehicle countermeasures must be properly evaluated. The PENDANT study commenced in January 2003 in order to explore the possibility of developing a co-ordinated set of targeted, in-depth crash data resources to support European Union vehicle and road safety policy. Three main work activity areas (Work Packages) commenced to provide these resources. This paper describes some of the outcomes of Work Package 2 (WP2, In-depth Crash Investigations and Data Analysis). In WP2, some 1,100 investigations of crashes involving injured car occupants were conducted in eight EU countries to a common protocol based on that developed in the STAIRS programme. This paper describes the purposes, methodology and results of WP2. It is expected that the results will be used as a co-ordinated system to inform European vehicle safety policy in a systematic, integrated manner. Furthermore, the results of the data analyses will be exploited further to provide new directions to develop injury countermeasures and regulations.
Interaction of road environment, vehicle and human factors in the causation of pedestrian accidents
(2005)
The UK On-the-Spot project (OTS) completed over 1500 in-depth investigations of road accidents during 2000-2003 and is continuing for a further 3 years. Cases were sampled from two regions of England using rotating shifts to cover all days of the week and all hours of the day and night. Research teams were dispatched to accidents notified to police during the shifts; arrival time to the scene of the accident was generally less than 20 minutes. The methodology of OTS includes sophisticated systems for describing accident causation and the interaction of road, vehicle and human factors. The purpose of this paper is to describe and illustrate these systems by reference to pedestrian accidents. This type of analysis is intended to provide an insight into how and why pedestrian accidents occur in order to assist the development of effective road, vehicle and behavioural countermeasures.
Der Beitrag berichtet in einem ersten Teil über die in den Niederlanden angewendeten Inspektionstechniken zur Feststellung von Schäden (Rissen) bei orthotropen Stahlfahrbahnplatten und in einem zweiten Teil über die Instandsetzung der Moerdijkbruecke mit einer zusätzlichen Deckschicht aus bewehrtem hochfesten Stahlfaserbeton. Die Ausführungen zu den Inspektionstechniken umfassen die visuelle Inspektion, magnetische Inspektion, Farbeindringprüfung, Ultraschallprüfung und Diffraktionseffekt bei Anstrahlen von Fehlern (Time of Flight Diffraction (TOFD)) sowie radiographische Untersuchungen und das Wirbelstromverfahren. Für jede dieser Methoden wird ihre Wirkungsweise, Handhabung und der Anwendungsbereich angegeben. Die Moerdijkbrücke ist eine der meistbefahrenen Brücken in den Niederlanden mit einem erheblichen Schwerverkehrsaufkommen und weist etliche Schäden am Deckblech auf. Die bisher durchgeführte Instandsetzung durch Ausbessern der Längsschweissnähte führte nicht zum erhofften Erfolg. Der Bauherr entschloss sich daher, die Gussasphaltschicht durch einen bewehrten hochfesten Stahlfaserbeton mit einer Dicke von 5 cm mit Verbund zum Stahldeckblech zu ersetzen. Die Spannungen im Deckblech konnten auf diese Weise um einen Faktor 4 bis 5 reduziert werden. Die Methode reagiert jedoch empfindlich auf Abweichungen der Mischungsverhältnisse des Betons und der Viskosität.
In this study, we compared the injury severity of occupants according to the seating position and the crashing direction in motor vehicle accidents. In the driver's point of view, it was separated the seating position as "Near-side" and "Far-side". The study subjects were targeted by people who visited 4 regional emergency centers following motor vehicle accidents. Real-world investigation was performed by direct and indirect methods after patient- consent. The information of the damaged vehicle was informed by Collision Deformation Classification (CDC) code and the information of the injury of patients was informed by using the Abbreviated Injury Score (AIS) and Injury Severity Score (ISS). When the column 3 in CDC code was P, damaged at the middle part of lateral side, the average point of AIS 3 was 1.91-±1.72 in near-side and 1.02-±1.31 in far-side (p<0.01). The average point of maximum AIS (MAIS) was 2.78-±1.39 in near-side and 2.02-±1.11 in far-side (p<0.01). The average point of ISS was 15.74-±14.71 in near-side and 8.11-±8.39 in far-side (p<0.01). Also, when the column 3 in CDC code was D, damaged at the whole part of lateral side, it was significant that the average point of AIS 3 and MAIS in near-side was bigger than in far-side (p=0.02).
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Side impacts, both nearside and farside, have been indicated by research to be responsible for a large proportion of serious injuries from road crashes. This study aimed to compare and contrast the characteristics of nearside and farside crashes in Australia, Germany and the U.S., using the ANCIS, GIDAS and NASS/CDS in-depth-databases, in order to establish the impact and injury severity associated with these crashes, and the types of injuries sustained. The analyses revealed some interesting similarities, as well as differences, between both nearside and farside crashes, and the emergent trends between the three investigated countries. More specifically, it was indicated that whilst the severity of injury sustained in nearside crashes was slightly greater overall than that found for farside crashes, careful consideration of struck and nonstruck side occupants must be made when considering aspects such as vehicle design and occupant protection.
A change emerges in hospital landscape due to health political measures, which in consequence also influences the pre-clinical medical care of emergencies. The main focus of this study was to gather information about emergency medical care after traffic accidents on the basis of data of Bavarian emergency medical services. In Bavaria, in 2006 it was necessary to call an emergency doctor in the case of 14.261 traffic accidents. Predominantly the patients were provided by land-based life saving appliances, air rescue services were only applied in 19.1 % of the cases. 47.6 % of patients being involved in a traffic accident were transported into a primary health care hospital. A prehospital interval of more than 60 minutes was calculated in 20 % of emergency care. 96.2 % of the patients were transported to hospitals of tertiary or maximum supply by air rescue services. The life saving appliances" readiness for action is however restricted to daylight. A further limitation appeared for routine office hours in hospitals: Only 36.7 % of accidents occurred in this time frame. An increase of hospitalizations in clinics of maximum supply appeared from 2002 until 2006 while simultaneously the prehospital period was extended. To assure a sufficient medical care of seriously injured persons further on, a fulltime and area-wide expostulation of efficient facilities is necessary. For this purpose it is necessary to establish regional trauma networks as well as emergency medical service at night time. Beyond that, a cost efficient compensation of the structural, personnel and logistic expenses has to be assured.
The project UR:BAN "Cognitive assistance (KA)" aims at developing future assistance systems providing improved performance in complex city traffic. New state-of-the-art panoramic sensor technologies now allow comprehensive monitoring and evaluation of the vehicle environment. In order to improve protection of vulnerable road users such as pedestrians and cyclists, a particular objective of UR:BAN is the evaluation and prediction of their behaviour and actions. The objective of subproject "WER" is development support by providing quantitative estimates of traffic collisions at the very start and predict potential in terms of optimized accident avoidance and reduction of injury severity. For this purpose an integrated computer simulation toolkit is being devised based on real world accidents (GIDAS as well as video documented accidents), allowing the prediction of potential effectiveness and future benefit of assistance systems in this accident scenario. Subsequently, this toolkit may be used for optimizing the design of implemented assistance systems for improved effectiveness.
Das Fehlen der Fahreignung stellt im Sinne der ICF eine Barriere bei der Teilhabe am Arbeitsleben dar. Die dargestellten Ergebnisse zeigen auf, dass weiterer Forschungsbedarf zum Thema Fahreignung und Therapie besteht, um den Patienten die Aussicht auf eine berufliche Reintegration zu bewahren. Durch ein effektives Training der Fähigkeiten zum Führen eines Kraftwagens könnten bei einem relevanten Anteil der Patienten die Voraussetzungen zur Teilhabe am Arbeitsleben stark verbessert werden. Durch die Präsentation dieser Ergebnisse kann eine Verbesserung des Problembewusstseins erwartet werden, da immer noch nicht alle Patienten über mögliche Einschränkungen der Fahreignung aufgeklärt werden. Daneben muss dem Fachpublikum die Notwendigkeit aufgezeigt werden, über neue Rehabilitationsstrategien zur Wiedererlangung beziehungsweise Verbesserung der Fahreignung nachzudenken.
Safety of light goods vehicles - findings from the German joint project of BASt, DEKRA, UDV and VDA
(2011)
Light goods vehicles (LGVs) are an important part of the vehicle fleet, providing a vital component in the European transportation system. On the other hand, LGVs are in the focus of public discussion regarding road safety. In order to analyse the accident situation of LGVs in an objective manner, Federal Highway Research Institute (BASt), VDA, DEKRA and German Insurers Accident Research (UDV) launched a joint project. The aim of this project, which will be finished by mid of 2011, is to identify reasonable measures which will further improve the safety of LGVs. For the first time, these partners jointly together conducted a research project and put together their know-how in accident research. Analyses are based on real-life accident data from the GIDAS database, the Accident Database of UDV (UDB), the DEKRA database and national statistics. The findings deliver answers to questions within the arena of future legislative actions and consumer protection activities. The analyses of databases cover areas of primary and secondary safety of LGVs with a special focus on advanced driver assistance systems (ADAS), driver behaviour as well as partner and occupant protection. Key figures from national statistics are used to highlight hotspots of accidents of LGVs in Germany. Finally, the proposed countermeasures are assessed regarding their potential effectiveness. Amongst others, the results show that the accident situation of LGVs is very similar to that of passenger cars. Noteworthy variations could be found in collisions with pedestrians, at reversing and regarding accident causes. Occupant safety of LGVs is on a higher level compared to cars. Results indicate that seatbelt use is on a significantly lower level compared to cars. This leads to higher-than-average injury risk for unbelted LGV occupants. When it comes to partner protection, there are problems with compatibility at LGVs. For car occupants there is a very high injury risk when colliding with a LGV. It indicates that higher passive safety test standards for LGVs would be counterproductive if they further increase stiffness of LGVs. The analysis of LGV-pedestrian accidents shows that pedestrian kinematic differs significantly from car-pedestrian accidents. At this point, existing pedestrian related test standards developed for cars cannot be adopted to LGVs. When it comes to active safety, ESC proved its effectiveness once again. Beyond that, rear view cameras, advanced emergency braking systems and lane departure warning systems show a safety potential, too. In addition to any technical countermeasures previously discussed, the importance of the driver behavior and attitude regarding the accident risk was investigated. In order to develop successful actions it is important to understand the main target population. In the case of LGV especially the crafts business and smaller companies are the major contributors the safety issue.
In recent years special attention has been paid to reducing the number of fatalities resulting from road traffic accidents. The ambitious target to cut in half the number of road users who are killed each year by 2010 compared with the 2001 figures, as set out in the European White Paper "European Transport Policy for 2010: Time to Decide" implies a general approach covering all kinds of road users. Much has been achieved, e.g. in relation to the safety of car passengers and pedestrians but PTW accidents still represent a significant proportion of fatal road accidents. More than 6,000 motorcyclists die annually on European roads which amounts to 16% of the EU-15 road fatalities. The European Commission therefore launched in 2004 a Sub- Project dealing with motorcycle accidents within an Integrated Project called APROSYS (Advanced PROtection SYStems) forming part of the 6th Framework Programme. In a first step, the combined national statistical data collections of Germany, Italy, the Netherlands and Spain were analysed. Amongst other things parameters like accident location, road conditions, road alignment and injury severity have been explored. The main focus of the analysis was on serious and fatal motorcycle accidents and the results showed similar trends in all four countries. From these results 7 accident scenarios were selected for further investigation via such in-depth databases as the DEKRA database, the GIDAS 2002 database, the COST 327 database and the Dutch element of the MAIDS database. Three tasks, namely the study of PTW collisions with passenger cars, PTW accidents involving road infrastructure features, and motorcyclist protective devices have been assessed and these will concentrate inter alia on accident causes, rider kinematics and injury patterns. A detailed literature review together with the findings of the in-depths database analysis is presented in the paper. Conclusions are drawn and the further stages of the project are highlighted.
Die aktuellen Richtlinien zur Bestimmung der Blutalkoholkonzentration (BAK) für forensische Zwecke (BAK-Richtlinie, 2007) lassen unter bestimmten Bedingungen auch zwei verschiedene gaschromatographische Analysen anstatt der häufig angewandten Kombination Gaschromatographie und enzymatische Methode ADH zur Bestimmung des Blutalkoholgehaltes zu. Untersucht wurde die Messpräzision zweier gaschromatographischer Verfahren bei der Alkoholanalytik im Vergleich zur häufiger angewandten Methodenkombination. In mehr als 50 Prozent der Fälle hat sich bei den verglichenen Methodenkombinationen ein identischer Mittelwert ergeben. Ansonsten waren die Abweichungen gering. Damit werden die hohen Anforderungen, die an die forensische Blutalkoholbestimmung gestellt werden, durch die modernen Laborautomaten erfüllt.
Um die Sicherheit der Straßentunnel zu gewährleisten, werden mehr als 400 m lange Tunnel ständig durch eine Tunnelleitzentrale überwacht. Die dort eingehende Flut von Einzelinformationen, wie Kamerabilder und zahlreiche Sensordaten, muss permanent durch das Personal erfasst und beurteilt werden. Das Projekt ESIMAS (Echtzeit-Sicherheits-Management-System für Straßentunnel) wird neue Wege aufzeigen, um die Leitstellenmitarbeiter zu unterstützen. Auf Grundlage der Datenanalyse und -bewertung von ESIMAS können zukünftig sicherheitsrelevante Ereignisse, wie ein Brand im Tunnel, zuverlässig und rechtzeitig erkannt werden. Im Ernstfall soll ESIMAS dem Leitzentralenpersonal sowie den Einsatz- und Rettungsdiensten Handlungsempfehlungen zur Ereignisbewältigung zur Verfügung stellen. Auf Basis dieser Handlungsempfehlungen können Maßnahmen schnellstmöglich und gezielt durchgeführt werden. Der innovative Ansatz von ESIMAS besteht in der ganzheitlichen Betrachtung aller Einzelinformationen und ihrer automatischen Auswertung und Bewertung. Hierdurch ist eine schnellere Reaktion der Leitstelle zum Schutz der Verkehrsteilnehmer möglich.
Betonfahrbahndecken werden seit vielen Jahrzehnten mit guten Gebrauchseigenschaften und langer Nutzungsdauer hergestellt. Um den wachsenden Anforderungen hinsichtlich der Verkehrssicherheit, der Umweltverträglichkeit und der Wirtschaftlichkeit gerecht werden zu können, ist eine stetige Weiterentwicklung erforderlich. Im September 2006 fand in Brüssel das 10. Internationale Betonstraßen Symposium statt. Im Rahmen umfangreicher Forschungsarbeiten und Studien auf Erprobungsstrecken wurden auf internationaler Ebene Untersuchungen zur Dauerhaftigkeit von Betonfahrbahnen durchgeführt. Der vorliegende Bericht stellt die Zusammenfassung von insgesamt 12 Fachbeiträgen aus 9 Nationen zum Themenblock "Kosteneffiziente und langlebige Straßen" dar.
In dem Beitrag präsentieren die Autoren einige laufende und geplante Forschungsvorhaben der Bundesanstalt für Straßenwesen (BASt), die wesentliche Bestandteile der Forschungslinie (FL) Q5 "Innovationen: Von der Idee in die Praxis" der mittelfristigen Forschungsplanung der BASt darstellen. Bei den konkreten Projekten geht es um die Entwicklung eines geeigneten Bewertungsverfahrens für Innovationen, um das Sichten neuer Forschungsideen aus denen neue Forschungsvorhaben resultieren können, um Nutzung von numerischen Methoden für die Entwicklung neuer Baustoffe und Bauweisen, sowie um den Aufbau einer geeigneten Untersuchungsinfrastruktur.
Die Straßenverkehrsinfrastruktur und der Straßenverkehr müssen sich künftig vielen Herausforderungen stellen. Zu nennen sind hier die Globalisierung, die Nachhaltigkeit, der Anstieg des Güterverkehrs und der technologische, demografische und klimatische Wandel. Die Straßenverkehrsinfrastruktur und der Straßenverkehr müssen sich den prognostizierten und projizierten Veränderungen anpassen. Die BASt betreut in ihrer Strategie "Anpassung der Straßenverkehrsinfrastruktur an den Klimawandel (AdSVIS)" bereits mehr als ein Dutzend Projekte. Diese Strategie soll dazu beitragen, die Verwundbarkeit gegenüber den Folgen des Klimawandels zu mindern bzw. eine leistungsfähige Straßenverkehrsinfrastruktur zu erhalten. Hierfür entscheidend sind nicht nur die durchschnittlichen Änderungen von klimatischen Parametern, sondern mehr noch das Auftreten von Extremwetterereignissen. Geringe Änderungen bei den Mittelwerten können sich aber in hohen Zunahmen bei der statistischen Verteilung der Extremwerte wie z. B. Hitzeperioden, Starkregen, Sturmböen äußern. Der zentrale Punkt der Anpassungsstrategie ist die Risikoanalyse wichtiger Güter- und Transitverkehrsachsen unter Einbeziehung von Seehäfen. Das Ziel dieses Projektes ist die Identifikation, Analyse und Bewertung der Risiken aus den projizierten Klimaänderungen für ausgewählte Streckenabschnitte im deutschen Teil des TEN-T (Transeuropäisches Netz Transport) in Anlehnung an die im ERA-NET ROAD Projekt RIMAROCC entwickelte Methodik. Hierfür werden für die relevanten meteorologischen Parameter Grenzwerte ermittelt, bei deren Überschreitung es für die Elemente der Straßenverkehrsinfrastruktur aus den Bereichen Erdbau, Entwässerung, Straßenbefestigungen, Ingenieurbau und Verkehrstechnik problematisch bzw. kritisch werden kann. Dabei werden nicht nur nach aktuellen Stand der Technik gefertigte Abschnitte des Straßennetzes betrachtet, sondern auch solche älterer Bauweisen und deren Vorkommen im Netz. Über die Fusion der Straßennetzdaten mit regionalisierten Klimaprojektionen werden schließlich die Lokalitäten mit prioritärem Anpassungsbedarf ermittelt. Anschließend werden für die identifizierten Risikobereiche erforderliche Anpassungsmaßnahmen entwickelt, erprobt und hinsichtlich ihrer Wirksamkeit bewertet. Da im Fokus die kostenintensiven Elemente der Straßenverkehrsinfrastruktur mit langer Nutzungsdauer wie Brücken und Straßengründungen stehen, müssen Anpassungsmaßnahmen bereits bei zeitnah anstehenden Erneuerungsarbeiten erfolgen, um die Folgenkosten der Klimaänderung zu senken. Das derzeit laufende Projekt "Risikoanalyse wichtiger Güter- und Transitverkehrsachsen unter Einbeziehung von Seehäfen" stellt eine erste Annäherung an den Aufbau eines Risikomanagements dar. Die hierbei verwendete RIMAROCC-Methodik muss dazu erweitert, weiterentwickelt und validiert werden. Erst dann kann die Risikoanalyse auf Netzebene durchgeführt und die erforderlichen Anpassungsprogramme aufgestellt werden.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.
Automotive Engineering, Mechanical Engineering and TechnologyrnAbstract: The degrees of injury severity, as a rule injuries scaled by AIS of specific regions of the human body, investigated out of road traffic accidents correspond to the body-specific loading values, which are found out with the aid of experimental or mathematical simulation of crash tests with motor vehicles or with sled tests. The coherence between the injured human being on the one hand and the physical and the theoretical model respectively on the other hand is established by the risk function, which describes the probability of degrees of injury severity in dependence on the protection criteria. Due to the different physical characteristics in the simulation, e.g. accelerations, forces, compressions and their velocity, the compilation of these quantities, comparable to the MAIS, the maximal occurred single AIS obtained in accident analysis is much more difficult in the simulation than in the accident occurrence. Therefore it is obvious to normalize the loading values gained out of simulation and to summarise them to an entire value in a suitable manner, the safety index.rn
One goal of the assessment of the crashworthiness of passenger cars is to characterize the potential of injury outcome to occupants of cars involved in an accident. This can be achieved by the help of an index that puts the number of injured occupants of passenger cars in relation to the number of cars involved in an accident. As a consequence, this index decreases with a lower potential of injury and rises with a higher number of injuries while assuming a fixed number of accidents. Another index is introduced that uses an economical weighting of each injury level. The consequential injury costs are calculated using the average economical costs for lightly, severely and fatally injured persons. The calculation of the safety indices is based on an anonymized sample of accident data provided by the Federal Statistical Office. An index of Mercedes passenger car drivers depending on the year of registration between 1991 and 2006 is compared to the index of drivers of cars of other makes within the same range of registration years.
This study aimed to identify the occurrence, type and mechanisms of the traumatic injuries of the vulnerable road users in vehicle collisions, and to determine the effects of human, engineering, and environment factors on traffic accidents and injuries. The pedestrian accident cases were collected in the years 2000 to 2005 from Changsha Wujing hospital China and Accident Research Unit at Medical University Hannover in Germany. A statistic analysis was carried out using the collected accident data. The results from analysis of Changsha data were compared with results from analysis of GIDAS data Hannover. The injury severities were determined using AIS code and ISS values. The results were presented in terms of cause of injuries, injury distributions, injury patterns, injury severity. The factors influenced the injury outcomes were proposed and discussed for the vehicle transport environment and road users. The results were discussed with regard to accident data collection, accident sampling and injury distributions etc. In the urban area of Changsha, motorcycles and passenger cars are most frequently involved in vehicle pedestrian accidents. Head and lower extremities injuries are the predominant types of pedestrian injuries. The pedestrian accidents were identified as vital issue in urban traffic safety and therefore a high priority should be given to this road user group in research of safe urban transportation. In Hannover area, cars are most frequently involved in traffic accidents, injured pedestrians are involved in road traffic of Germany in 13% of all causalities only in 2005 and have nearly the same number as motorcyclists, but the half of bicyclists.
Accident research 2.0: New methods for representative evaluation of integral safety in traffic
(2013)
BMW has developed a procedure for rating Advanced Driver Assistance Systems (ADAS) benefits that integrates two distinct tools. The tool "S.A.F.E.R." is designed to analyze the pre-crash phase. The aim of S.A.F.E.R. is to simulate all relevant processes in sufficient detail to obtain reproducible estimates of key indicators (effectiveness, false positives, etc.). The relevant processes include not only traffic and vehicle dynamics, but also environmental and most importantly human factors. Representative distributions of factors and parameters are obtained by taking the stochastic variation of all relevant parameters into account in the simulations. The second tool, known as "ICOS", has been designed to provide a high-resolution, high-fidelity description of crash phase dynamics. If one converts the outputs of stochastic simulation into inputs for crash dynamics, the result is a comprehensive description of exactly how a safety system can reduce injuries. Applications currently focus on high-fidelity simulation of individual crashes in order to enhance our understanding and optimization of connected safety systems. An integrated simulation process thus allows an exact prediction of the effectiveness in individual cases in terms of injury severity. The development and rating of integral safety need to reflect the true efficiency in the field. The integrated approach described here could provide a valid and reproducible basis for rating connected systems of active and passive safety. In particular, "virtual experiments" using a traffic-based approach and incorporating models of all relevant processes constitute an essential element of the approach.
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
The incidence and treatment of sternal fractures among traffic accidents are of increasing importance to ensure best possible outcomes. Analysis of technical indicators of the collision, preclinical and clinical data of patients with sterna fractures from 1985-2004 among 42,055 injured patients were assessed by an Accident Research Unit. Two time groups were categorized: 1985-1994 (A) vs. 1995-2004 (B). 267/42,055 patients (0.64%) suffered a sterna fracture. Regarding the vehicle type, the majority occurred after car accidents in 0.81% (251/31,183 pts), followed by 0.19% (5/2,633pts) driving motorbike, and 0.11% (4/3,258pts) driving a truck. 91% wore a safety belt. Only 13% of all passengers suffering a sternal fracture had an airbag on board (33/255 car/trucks), with an airbag malfunction in 18%. The steering column was deformed in 39%, the steering wheel in 36%. Cars in the recent years were significantly older (7.67-±5 years (B) vs. 5.88-±5 years (A), p=0.003). Cervical spine injuries are frequent (23% vs. 22%), followed by multiple rib fractures (14% vs. 12%) and lung injuries (12% vs. 11%). We found 9/146 (6%) and 3/121 patients (3%) with heart contusion among the 267 sternal fractures. MAIS was 2.56-±1.3 vs. 2.62-±1.3 (A vs. B, p=0.349). 18% of patients were polytraumatized, with 11.2% dying at the scene, 2.3% in the hospital. Sternal fractures occur most often in old cars to seat-belted drivers often without any airbag. Severe multiple rib fractures and lung contusion are concomitant injuries in more than 10% each indicating the severity of the crash. Over a twentyyear period, the injury severity encountered was not different with 18% polytrauma patients suffering sternal fractures.
The European Union has set a target to reduce all road fatalities (over 40,000) with 50% in 2010. This target percentage remained unchanged with the introduction of the ten new member states within the EU as by May 1st, 2004. According to Eurostat, 34% of all fatalities in 1998 in the, then, fifteen states of the European Union were the result of single vehicle collisions. This represents over 14,000 lives lost each year of which many can likely be saved through better roadside infrastructure design. The challenge for road safety professionals is to find methods and design strategies that help to reduce these casualties. Procedures for full-scale vehicle crash testing of guard rails were first published in the US in 1962. Present European regulation is mainly based on these procedures and later developments. Since then the vehicle fleet has changed considerably. Due to the complexity of the actual safety problem the numerical simulation approach offers a good opportunity to evaluate the different parameters involved in road safety, such as infrastructure properties, vehicle type, vehicle occupants and injuries. The ideal situation would be that simulation tools are coupled or integrated and all involved effects would be related. At the moment this is not the case yet, but initiatives are taken and a new virtual era has started. This paper offers a method looking at two components that encompass the driving environment: the car and the guardrail. As part of the EC-funded project, RISER (Roadside Infrastructure for Safer European Roads) a multi body simulation program study is carried out to determine sensitivities of some parameters in car to guardrail collisions and gives insides in performance of the car with passive safety equipment, the guardrail and the interaction of these objects with each other. By offering a set of methods that includes these two aspects and their intertwining relations, more confidence can be gained in actually reducing fatalities due to single vehicle collisions with, or due to, roadside furniture. Reducing the number of fatalities of single vehicle crashes would contribute greatly to the stated goal of reducing casualties altogether.
The practicability and feasibility of using alcohol ignition interlock devices has been discussed for more than 15 years in Germany. Thereby, judicial issues have been treated conversely. Consensus exists about the fact that the voluntary use of alcohol ignition interlocks is in all areas of possible use recommendable. Great reservation is shown concerning the operation of the devices for DUI (Driving Under Influence) offenders. Main doubts regard the missing legal base for application in such cases and potential circumvention attempts while the need of supportive psychological measures is unquestioned. In 2011, the Ministry of Transport, Building and Urban Affairs entered this topic in its newly released traffic safety programme as a matter of future research. Almost in parallel, the Federal Highway Research Institute (BASt) launched an alcohol ignition interlock project for DUI offenders. The study at hand aimed at developing a comprehensive programme concept for the use of alcohol ignition interlocks as additional measure to psychological rehabilitation for DUI offenders. Expert surveys serve as input for the establishment of a widely accepted innovative concept for nationwide implementation. By means of a pilot trial, the added value of using a combination of structural (alcohol interlock) and individual (psychological measure) intervention for DUI offenders to the existing countermeasure system should be studied. In addition, selection criteria for DUI offenders eligible for future programme participation should be defined. The majority of the experts evaluate the introduction of alcohol ignition interlocks as a good option to enhance traffic safety. The possibility of early psychological rehabilitation is emphasized in the process. Those who do not approve alcohol ignition interlock usage estimate the amount of offenders eligible for such programmes too small. The survey also revealed that legal regulations for issuing an alcohol interlock restricted licence to DUI offenders is missing. Hence, a possible amendment to the German Driving Licencing Regulation was developed within the project. Consultations with the Ministry of Transport, Building and Urban Affairs and the Ministry of Justice disclosed the need for a change of the road traffic law before an amendment to the existing regulations may be put into force. At least, the person responsible in the Ministry of Justice developed a proposal for the law section that needs revision. All in all, it became clear within the process of the project that a field trial in Germany is still a distant vision. Nevertheless, all institutions involved are motivated to deal with the matter further on in order to pave the way for a soon start of the pilot trial.
The use of alcohol interlocks for DUI offenders is widespread around the world. in North America and Australia alcohol interlocks are core elements in the countermeasure system against DUI recidivism. Based on a European experience exchange hosted by the Federal Highway Research Institute (BASt) in October 2013, key features of European alcohol interlock programmes are illustrated. In addition, key findings from international alcohol interlock research are presented. They point towards a need for an accompanying rehabilitative measure in order to achieve long-lasting behavioural changes in the offender. Data from the interlock recorder can be used as predictor for recidivism risk, but also as objective data to aid counselling. Finally, an example of an accompanying rehabilitative measure, which was specifically developed for interlock programmes within a BASt project, is given.
Im Oktober 2007 wurde die Rügenbrücke, eine der längsten Hochbrücken Europas, für den Verkehr freigegeben. Der Beitrag befasst sich mit den Erfahrungen, die bei Planung und Bau dieses bemerkenswerten Bauwerks gemacht wurden, insbesondere hinsichtlich der vielen bautechnischen Innovationen bei dem Schlüsselbauwerk des Brückenzuges, der 570 m langen Schrägseilbrücke über den Ziegelgraben. Eine der wesentlichen Erstanwendungen für Deutschland betraf die Ausführung der Schrägseile mit Litzenbündeln des Systems DYNA Grip der SUSPA DSI. Wegen des aus Gründen des Vogelschutzes erforderlichen Mindestdurchmessers der Seile von 12 cm waren vollverschlossene Seile aus ingenieurtechnischen und wirtschaftlichen Gründen benachteiligt, sodass sich der Bauherr für Seile aus Litzenbuendeln entschied. Die Schrägseilbrücke über den Ziegelgraben wird schon jetzt als modernes Wahrzeichen der Stadt Stralsund empfunden. Sie passt sich gestalterisch hervorragend in die Umgebung ein und beeinträchtigt auch nicht die zum Weltkulturerbe zählende Altstadt von Stralsund. Besonders besticht das Bauwerk durch seine Leichtigkeit und die Einpassung der Formen der Bauteile, zum Beispiel wegen der tropfenfoermigen Gestaltung des Pylons und der Pfeiler, in das maritime Umfeld. Da die verwendeten Schrägseil-Litzenbündel noch nicht allgemein bauaufsichtlich zugelassen sind, kam der Qualitätssicherung für die Seile in allen Stufen der Planung, Fertigung, Montage und Bauwerksprüfung eine herausragende Bedeutung zu. Der zugehörige Qualitätssicherungsplan wird im Bericht ausführlich mit den wesentlichen \"schrägseilspezifischen\" Maßnahmen beschrieben. Schwingungen und Ermüdungsbeanspruchungen der Seile durch Fahrverkehr und Wind liessen sich durch einen mehrstufigen, kontinuierlich verdichteten Planungsprozess unter Nutzung von Versuchsdaten und Messungen am Bauwerk wirkungsvoll beherrschen. Aus Sicht der Bauwerksprüfung bestanden anfänglich Bedenken wegen der Erreichbarkeit der bis in 80 m Höhe über dem Brückendeck gespannten Schrägseile und der nicht direkt zugänglichen Litzen innerhalb des Hüllrohres sowie der Verankerungen. Daher wurden alle verfügbaren Prüfverfahren für Schrägseile an der Rügenbrücke getestet. Daraus ergab sich eine Prüfmatrix aus Prüfverfahren, Prüfmittel und Prüfumfang für die gesamte Nutzungsdauer. Zusammenfassend wird festgestellt, dass bei der Ziegelgrabenbrücke Schrägseile aus Litzenbündeln eine den vollverschlossenen Seilen ebenbürtige Bauart darstellen.