Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (62)
- Buch (Monographie) (41)
- Wissenschaftlicher Artikel (12)
- Teil eines Buches (Kapitel) (2)
- Bericht (2)
Schlagworte
- Simulation (119) (entfernen)
Im Rahmen des Forschungsprojektes wurden für verschiedene Tunnel mit Rechteck- und Gewölbequerschnitt mit dem Regelquerschnitt RG 31t (bzw. RQ 10,5), die orts- und zeitabhängigen Verteilungen der Gastemperatur, der Gasgeschwindigkeit und Gaszusammensetzung, der adiabaten Decken- und Wandtemperaturen sowie der zeitliche Verlauf der Wärmefreisetzungsrate und des Durchwärmungsverhaltens bestimmt werden. Betrachtet wurden Tunnel mit konstanter Längsneigung von 3 % sowie ein Tunnel mit muldenfoermigem Längsprofil (Richtungs- und Gegenverkehr). Bezüglich der Austrittgeschwindigkeit wurden die Szenarien 20,6 kg/s und 300 kg/s unterschieden. Zusätzlich im Fall A ein mit Holzpaletten beladenen LKW und im Fall B zusätzlich noch weitere PKW und LKW berücksichtigt. In einem originalmaßstäblichen Großbrandversuch wurde zur Klärung offener, aus der Modellierung resultierender Fragen ein Unfall in einem Richtungsverkehrstunnel zwischen einem LKW, der mit ca. 3,7 t Europoolpaletten beladen war, und einem PKW nachgebildet. Insgesamt wurden 3 Mittelklasse-PKW im Versuchstunnel positioniert. Die Brandlast betrug ca. 123 GJ. Anhand durchgeführter Plattenbrandversuche wurde festgestellt, dass die Schichten aus spritzbarem Faserbeton des Systems RUB sowie die Fertigteilschutzschichten des Systems HOCHTIEF ein relativ geringes bzw. kein Abplatzverhalten aufweisen und bei Brandbeanspruchung jeweils einen signifikanten thermischen Schutz der Stahlbetonkonstruktion gewährleisten können. Es konnte gezeigt werden, dass Auswirkungen auf die Tragstruktur nicht größer sind als infolge eines Brands, dessen Temperatur-Zeit-Verlauf dem ZTV-ING-Verlauf entspricht. Es sei aber angemerkt, dass aus den Szenarien unter noch ungünstigeren Bedingungen (z.B. im Falle eingeschränkt funktionsfähiger Schlitzrinnen) Auswirkungen entstehen könnten, die nur durch den verlängerten ZTV-ING-Temperatur-Zeit-Verlauf abgedeckt wären.
This paper presents findings of a laboratory experiment which aimed at evaluating the sensitivity and intrusiveness of Tactile Detection Response Task (TDRT) methodology. Various single-task, dual-task and triple-task scenarios were compared. The task scenarios included a surrogate of driving (tracking task) and different secondary tasks (N-back, surrogate reference task (SuRT)). The results suggest that the TDRT is sensitive to load levels of secondary tasks which primarily demand for cognitive resources (N-back). Sensitivity to variations of visual"manual load could not be shown (SuRT). TDRT seems also to be able to differentiate between modes of primary task which varies in terms of cognitive load (visual against auditory tracking task). Results indicated intrusiveness of TDRT on primary task performance and secondary task performance depending on the type of underlying task scenario. As a conclusion, TDRT can be recommended as a method to assess attentional effects of cognitive load of a secondary task, but should be used with caution for secondary tasks with strong motor demands.
Bei der Nachrechnung bestehender Spannbetonbrücken auf Grundlage aktueller Normen zeigen sich i.A. erhebliche Defizite bei der erforderlichen Querkraftbewehrung. Dies ist zum einen auf höhere Verkehrslasten infolge des kontinuierlich gestiegenen Schwerverkehrs und zum anderen auf die Weiterentwicklung der Verfahren zum Nachweis der Querkrafttragfähigkeit zurückzuführen. Zudem erfolgte in Deutschland erst im Jahr 1966 die Festlegung einer erforderlichen Mindestquerkraftbewehrungsmenge. Die Nachweisverfahren für die Querkrafttragfähigkeit von Spannbetonbalken beruhen im Wesentlichen auf Versuchen an Einfeldträgern und sind bekanntlich sehr konservativ. Daher wurden am Lehrstuhl Betonbau der TU Dortmund in einem Großversuch experimentelle Untersuchungen zur Querkrafttragfähigkeit an einem vorgespannten Zweifeldträger durchgeführt, mit dem Ziel, Grundlagen für ein genaueres Nachweisverfahren zu schaffen. Von besonderem Interesse war das Tragverhalten im Bereich der Innenstütze. Die Gesamtlänge des Versuchsträgers betrug 12,0 m, die Stützweiten ergaben sich zu 5,75 m. Die Querkraftbewehrung des Balkens entsprach der rechnerisch erforderlichen Mindestquerkraftbewehrung nach DIN-Fachbericht 102. Lediglich in einem begrenzten Bereich unmittelbar neben der Innenstütze eines Feldes entsprach sie der doppelten Mindestquerkraftbewehrung. Da bisher kaum experimentelle Untersuchungen zum Querkrafttragverhalten an Innenstützen durchgeführt wurden, wurden die Verformungen in diesem Bereich während der Versuchsdurchführung zusätzlich mit einem optischen Messverfahren aufgezeichnet. Zur kontinuierlichen Erfassung des Tragverhaltens des gesamten Bauteils wurden zudem an der Querkraft- und Längsbewehrung des Versuchsträgers über 250 Dehnungsmessstreifen aufgebracht. Die Versuchsauswertung enthält eine umfangreiche Darstellung der Messwerte und zusätzlich Versuchsnachrechnungen unter Anwendung des Druckbogenmodells sowie mittels numerischer Simulationen.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
Im Rahmen der Untersuchung wurde der Einfluss von Lang-Lkw auf den Verkehrsablauf an planfreien Knotenpunkten mit Hilfe des mikroskopischen Simulationsprogramms BABSIM analysiert. Dazu wurde der Verkehrsablauf an verschiedenen Typen von Ausfahrten und Einfahrten sowie einer Verflechtungsstrecke nachgebildet. Die Simulationsmodelle der Untersuchungsstellen wurden anhand der Daten von Dauerzählstellen für Schwerverkehrsanteile zwischen 10 % und 15 % kalibriert und validiert. Für jede Untersuchungsstelle wurden Simulationen mit Lang-Lkw-Anteilen von 0 %, 1 %, 2 % und 5 % der Gesamtverkehrsstärke sowie in der Regel drei unterschiedlichen Verkehrsstärkeanteilen des ein- bzw. ausfahrenden Verkehrs durchgeführt. In einem weiteren Ansatz wurden Szenarien verglichen, bei denen die Transportleistung von drei herkömmlichen Lkw durch zwei Lang-Lkw ersetzt wurde. Für jedes Szenario wurde der Mittelwert der Verkehrsstärken vor Zusammenbrüchen des Verkehrsflusses als Schätzwert der Kapazität ermittelt. Insgesamt liefern die Ergebnisse der Verkehrsflusssimulationen einen Anhaltspunkt dafür, dass die Kapazität von planfreien Knotenpunkten bei den hier analysierten hohen Lang-Lkw-Anteilen von 1 bis 5 % der Gesamtverkehrsstärke im Allgemeinen nur gering beeinflusst wird. Die ermittelten Auswirkungen der Lang-Lkw auf die Kapazität liegen in der Größsenordnung der Bandbreite der Kapazität, die in der Realität auch im Vergleich unterschiedlicher Knotenpunkte mit ähnlichen verkehrlichen und streckengeometrischen Randbedingungen auftreten.
Assessment of the effectiveness of Intersection Assistance Systems at urban and rural accident sites
(2015)
An Intersection Collision Avoidance System is a promising safety system for accident avoidance or injury mitigation at junctions. However, there is still a lack of evidence of the effectiveness, due to the missing real accident data concerning Advanced Driver Assistance Systems. The objective of this study is the assessment of the effectiveness of an Intersection Collision Avoidance System based on real accidents. The method used is called virtual pre-crash simulation. Accidents at junctions were reconstructed by using the numerical simulation software PC-Crashâ„¢. This first simulation is called the baseline simulation. In a second step the vehicles of these accidents were equipped with an Intersection Collision Avoidance System and simulated again. The second simulation is called the system simulation. In the system simulation two different sensors and four different intervention strategies were used, based on a time-to-collision approach. The effectiveness of Intersection Collision Avoidance System has been evaluated by using an assessment function. On average 9% of the reviewed junction accidents could have been avoided within the system simulations. The other simulation results clearly showed a change in the principal direction of force, delta-v and reduction of the injury severity.
The main focus of the benefit estimation of advanced safety systems with a warning interface by simulation is on the driver. The driver is the only link between the algorithm of the safety system and the vehicle, which makes the setup of a driver model for such simulations very important. This paper describes an approach for the use of a statistical driver model in simulation. It also gives an outlook on further work on this topic. The build-up process of the model suffices with a distribution of reaction times and a distribution of reaction intensities. Both were combined in different scenarios for every driver. Each scenario has then a specific probability to occur. To use the statistical driver model, every accident scene has to be simulated with each driver scenario (combinations of reaction times and intensities). The results of the simulations are then combined regarding the probabilities to occur, which leads to an overall estimated benefit of the specific system. The model works with one or more equipped participants and delivers a range for the benefit of advanced safety systems with warning interfaces.
Detailed anthropometric data of pregnant women have been collected and used in the development of a computational model of the pregnant occupant model "Expecting". The model is complete with a finite element uterus and multi-body fetus, which is a novel feature in the models of this kind. The computational pregnant occupant model has been validated and used to simulate a range of impacts. The strains developed in the utero-placental interface are used as the main criteria for fetus safety. Stress distributions due to inertial loading of the fetus on the utero-placental interface play a role on the strain levels. Inclusion of fetus model is shown to significantly affect the strain levels in the utero-placental interface. This series of studies has led to the design of seatbelt features specifically for the pregnant women to enable them use the seatbelt correctly and comfortably.
The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx. However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My. The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was observed. It was also observed that the primary neck response in these tests was flexion, not extension. This correlates well with recent findings from Japan and the United States showing a correlation between neck flexion and injury in accident replication simulations and postmortem human subjects (PMHS) studies, respectively. The present certification tests may not adequately control front cervical spine bumper characteristics, which are important for neck flexion response. The certification sled test also does not include the pelvis and so cannot be used to control pelvis response and does not substantially load the lumbar bumpers and so does not control these parts of the dummy. The stiffness of all spine bumpers and of the pelvis flesh should be much more tightly controlled. It is recommended that a method for certifying the front cervical bumpers should be developed. Recommendations are also made for tighter tolerance on the input parameters for the existing certification tests.
It is commonly agreed that active safety will have a significant impact on reducing accident figures for pedestrians and probably also bicyclists. However, chances and limitations for active safety systems have only been derived based on accident data and the current state of the art, based on proprietary simulation models. The objective of this article is to investigate these chances and limitations by developing an open simulation model. This article introduces a simulation model, incorporating accident kinematics, driving dynamics, driver reaction times, pedestrian dynamics, performance parameters of different autonomous emergency braking (AEB) generations, as well as legal and logical limitations. The level of detail for available pedestrian accident data is limited. Relevant variables, especially timing of the pedestrian appearance and the pedestrian's moving speed, are estimated using assumptions. The model in this article uses the fact that a pedestrian and a vehicle in an accident must have been in the same spot at the same time and defines the impact position as a relevant accident parameter, which is usually available from accident data. The calculations done within the model identify the possible timing available for braking by an AEB system as well as the possible speed reduction for different accident scenarios as well as for different system configurations. The simulation model identifies the lateral impact position of the pedestrian as a significant parameter for system performance, and the system layout is designed to brake when the accident becomes unavoidable by the vehicle driver. Scenarios with a pedestrian running from behind an obstruction are the most demanding scenarios and will very likely never be avoidable for all vehicle speeds due to physical limits. Scenarios with an unobstructed person walking will very likely be treatable for a wide speed range for next generation AEB systems.