Sonstige
Filtern
Dokumenttyp
- Konferenzveröffentlichung (122) (entfernen)
Sprache
- Englisch (122) (entfernen)
Schlagworte
- Deutschland (122) (entfernen)
Institut
Causation of traffic accidents with children from the perspective of all involved participants
(2017)
In the year 2014 about 2,800 children between zero and 14 years got injured due to traffic accidents in Austria. More than 50% were taking part in traffic as active road users like cyclists or pedestrians. Within this study 46 real world traffic accidents between vehicles and children as pedestrians were analysed. In 39 cases, car drivers hit the crossing children. In the other cases, the collision opponents were busses, trucks or motorcycles. Most of the children got hit while crossing a road at urban sites. By analysing the traffic accidents from the perspectives of all involved participants, vehicle drivers and injured children, it is possible to identify factors for each participant, which led to the accident and factors that contributed the accident. The main task is to find patterns in the behaviour of crash victims (children and driver) before the collision. One important fact is that in more than 50% of the analysed cases sight obstructions were an important contributing factor for both, the driver and the child. From drivers view situations in which the child moved unexpected into the driven road lane were often found. For the injured child, factors like: no attention to the road traffic or no sufficient traffic observation were found to be relevant. Further it- possible to sensitise children and adults to possible source of critical traffic situations according to the findings of this study.
Introduction: The incidence of trauma-related cervical-spine fractures is 19-88 / 100.000. In contrast, the incidence of cervical spine injuries is as high as 19% - 51% of all spinal trauma. Cervical spine injuries in non-polytrauma patients are rare. However, due to the potential damage to the spinal cord these traumata are feared and mustn't be missed. Cervical spine injuries represent the highest reported early mortality rate of all spinal trauma. The rate of functional impairment afterwards is high and the rate of reintegration into work is low compared to other organ systems. In the past, trauma surgeons often did x-rays of the cervical spine with low inhibition threshold and often without strong clinical suggestion for vertebral or discoligamental injuries. This practice was queried by the Canadian C-Spine rule and extensively discussed in the past. Therefore we did a retrospective study whether non-polytrauma patients benefit from cervical spine x-rays.
Event data recorders (EDRs) are a valuable tool for in-depth investigation of traffic accidents. EDRs are installed on the airbag control module (ACM) to record vehicle and occupant information before, during, and after a crash event. This study evaluates EDR characteristics and aims at better understanding EDR performance for the improvement of accident reconstruction with more reliable and accurate information regarding accidents. The analysis is based on six crash tests with corresponding EDR datasets.
Cycle helmets have continued to increase in popularity since their introduction half a century ago. Many studies indicate that overall, head injury can be significantly reduced by wearing them. This study was conducted using two distinct sets of real-world cycling collision data from Ireland, namely cases involving police collision reports and cases involving admission to a hospital emergency department. The analyses sought to simulate and analyse the protective performance of cycle helmets in such collision scenarios, by comparing the Head Injury Criterion score and peak head accelerations, both linear and angular. Cycle collisions were simulated using the specialised commercial software MADYMO. From the simulation results, these key metrics were compared between the same-scenario helmeted and unhelmeted cyclist models. Results showed that the inclusion of bicycle helmets reduced linear accelerations very significantly, but also increased angular accelerations significantly compared to unhelmeted situations. Given the modest protective performance of cycle helmets against angular accelerations, it is recommended that cycle helmet manufacturers and international test standards need to pay more attention to head angular accelerations.
This study aimed at comparing head Wrap Around Distance (WAD) of Vulnerable Road User (VRU) obtained from the German in-depth Accident Database (GIDAS), the China in-depth Accident Database (CIDAS) and the Japanese in-depth Accident Database (ITARDA micro). Cumulative distribution of WAD of pedestrian and cyclist were obtained for each database (AIS2+) showing that WAD of cyclists were larger than the ones of pedestrians. Comparing three regions, the 50%tile WAD of GIDAS was larger than that of both Asian accident databases. Using linear regression that might predict WAD of pedestrians and cyclists from Impact speed and VRU height, WADs were calculated to be 206cm/219cm (Pedestrian/Cyclist) for GIDAS, 170cm/192cm for CIDAS and 211cm/235cm for ITARDA. In addition, this study may be helpful for reconsideration of WAD measurement alignment between accident reconstruction and test procedures.
In this study, we compared the injury severity of occupants according to the seating position and the crashing direction in motor vehicle accidents. In the driver's point of view, it was separated the seating position as "Near-side" and "Far-side". The study subjects were targeted by people who visited 4 regional emergency centers following motor vehicle accidents. Real-world investigation was performed by direct and indirect methods after patient- consent. The information of the damaged vehicle was informed by Collision Deformation Classification (CDC) code and the information of the injury of patients was informed by using the Abbreviated Injury Score (AIS) and Injury Severity Score (ISS). When the column 3 in CDC code was P, damaged at the middle part of lateral side, the average point of AIS 3 was 1.91-±1.72 in near-side and 1.02-±1.31 in far-side (p<0.01). The average point of maximum AIS (MAIS) was 2.78-±1.39 in near-side and 2.02-±1.11 in far-side (p<0.01). The average point of ISS was 15.74-±14.71 in near-side and 8.11-±8.39 in far-side (p<0.01). Also, when the column 3 in CDC code was D, damaged at the whole part of lateral side, it was significant that the average point of AIS 3 and MAIS in near-side was bigger than in far-side (p=0.02).
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
The current paper reports on the results of a pilot study aiming to investigate the effect of mobile telephone use on the driving performance of 5 amateur and 5 professional drivers. Their driving acuity was tested through a driving simulator. Analysis and interpretation of the results occurred comparing the drivers' driving performance while talking, reading messages and writing a message on the mobile phone (intervention time) with the drivers' driving performance engaged in no activity (control time). The variables affected by the mobile phone were the "steering", the "lane offset" and the "duration of lane offset". Moreover, the drivers involved in a car crash in the last five years appeared to differ from those who were not involved in a crash in both "lane offset" and "following distance". The results of this pilot study will inform the design of a large experimental study on 50 professional and 50 amateur drivers.
The utilisation of secondary-safety systems to protect occupants has attained a very high level over the past decades. Further improvements are still possible, but increasingly minor progress is only to be had with a high degree of effort. Thus, a key aspect must be the impact to overall safety in an accident. If reliable information is available on an imminent crash, measures already taken in the pre-crash phase can result in a significantly great influence on the outcomes of the crash. With this background preventive measures are the key to a sustainable further reduction of the figures of crash victims on our roads. This paper aims to show a preventive approach that can contribute to lessening the consequences of a crash by creating an optimum interaction of measures in the fields of primary and secondary safety. To further enhance vehicle safety, driver assistant systems are already available that warn the driver of an imminent front-to-rear-end crash. The next step is to support him in his reactions or if he fails to react sufficiently, to even initiate an automatic braking when the crash becomes unavoidable. Automatic pre-crash braking can, in an ideal situation, fully prevent a crash or can significantly reduce the impact speed and thus the impact energy (and the severity of the accident). If a vehicle is being braked in the pre-crash phase, the occupants are already being pre-stressed by the deceleration. The information available about the imminent crash can be used to activate the belt tensioners and likewise other secondary safety systems in the vehicle right before the impact. The pre-crash deceleration also causes the front of the vehicle to dip. Conventional crash tests do not take this specific impact situation into consideration. This is why, for example, the influences of the pre-crash displacements of the occupants are not recorded in the test results. Furthermore, a reproducible representation of the benefit of the vehicle safety systems which prepare the occupants for the imminent impact is not possible. In order to demonstrate the functions of automated pre-crash braking and to investigate the differences during the impact as a consequence of the altered occupant positions as well as the initiation of force and deformations of the vehicle front, DEKRA teamed up with BMW to carry out a joint crash test with the latest BMW 5 series vehicle. It involved the vehicle braking automatically from a starting test speed of 64 km/h (corresponding to the impact speed set by Euro NCAP) down to 40 km/h. The test was still run by the intelligent drive system of the crash test facility. This required several modifications to be made to the test facility as well as to the vehicle. The paper will describe and discuss some relevant results of the crash test. In addition, the possible benefits of such systems will also be considered. The test supplemented the work of the vFSS working group (vFSS stands advanced Forward-looking Safety Systems).
The incidence of side impacts was investigated from GIDAS data. Both vehicle-fixed object and vehicle-vehicle collisions were analysed as these are enclosed within the consumer testing program. Vehicle-fixed object collisions were stratified according to ESC availability. Results indicated that vehicles equipped with ESC rarely have pure-lateral impacts. An increase in oblique collisions was seen for the vehicles with ESC whereby most vehicle were driving in left curves. The analysis of vehicle-vehicle collisions developed injury risk curves were developed at the AIS3+ injury severity for the vehicle-vehicle side impacts. Results suggested that greatest injury risk occurred when a Pre Euro NCAP vehicle was struck by a Post Euro-NCAP vehicle. The remaining curves did not show different behaviour, indicating that stiffness increased have been equally combated. This was attributable to the few Post Euro-NCAP vehicles that had a deployed curtain airbag available in the sample. The integration of Euro NCAP testing has shown to improve vehicle crashworthiness for pole collisions, as those vehicles with ESC rarely incur lateral impacts.
Although the statistics show a decreasing rate of child injuries and fatalities in German road accidents more efforts can be made to protect children in cars e.g. by developing appropriate child restraint systems. An important part in of this work can be achieved with the help of crash tests using child dummies. However these crash tests cannot completely reflect the situation of real world crashes as factors like children moving out of the optimal position or children incorrectly fastened by their parents are difficult to predict. Therefore this study gives an overview over the current accident and injury situation of child occupants in cars in German road accidents.
Within the COST Action TU1101 the working group WG 1 is dealing with acceptance criteria and problems in helmet use while bicycling concerning conspicuity, thermal stress, ventilation deficits and other potential confounding. To analyze the helmet usage practice of bicyclists in Europe a questionnaire was developed in the scope of working group 1 to collect relevant information by means of a field study. The questionnaire consists of some 66 questions covering the fields of personal data of the cyclist, riding und helmet usage habits, information concerning the helmet model and the sensation of the helmet, as well as information on previous bicycle accidents. A second complementary study is conducted to analyze if the use of a bicycle helmet influences the seating geometry and the posture of cyclists when riding a bicycle and if the if the helmet vertically limits the vision. For this purpose cyclists with and without helmets were photographed in real world situations and relevant geometrical values such as the decline of the torso, the head posture of the upper vertical vision limit due to the helmet were established from the photos. The interim results of the field studies which were conducted in Germany by the Hannover Medical School are presented in this study. Some 227 questionnaires were filled out, of which 67 participants had used a helmet and 42 of the 227 participants have had a bicycle accident before. For the analysis of the riding position and posture of the cyclist over 40 pictures of riders with a helmet and over 240 pictures of riders without a helmet were measured concerning the seating geometry to describe the influence of using a bicycle helmet. Some results in summary: From the riders interviewed with the questionnaire only 11% of the city bike riders and 12% of the mountain bike riders always used the helmet, while 38% of the racing bike riders and 88% of the e-bike-riders always used the helmet. The helmet use seems not to change the sensation of safety of cycling compared to the use of a car. The arguments for not wearing a helmet are mostly stated to be the short distance of a trip, high temperatures or carelessness and waste of time. The reasons for using a helmet are stated to be the feeling of safety and being used to using a helmet. Being a role model for others was also stated to be a reason for helmet use. Concerning the sensation of the helmet 9% of the riders reported problems with the field of vision when using a helmet, 57% saw the problem of sweating too much, and 10% reported headaches or other unpleasant symptoms like pressure on the forehead when using the helmet. The analysis of the seating posture from the pictures taken of cyclists revealed that older cyclists generally have a riding position where the handle bar is higher than the seat (0-° to 10-° incline from seat to handlebar), while younger riders had a higher variance (between -10-° decline and 20-° incline). Further, elderly riders and riders with helmets seem to have a more upright position of the upper body when cycling. The vertical vision limit due to the helmet is determined by the front rim of the helmet (mostly the sun shade). Typical values here range from 0-° (horizontal line from the eye to the sun shade) to 75-° upwards, in which elderly riders tend to have a slightly higher vertical vision limit possibly due to the helmet being worn more towards the face.
The Decision Support System (DSS) is one of the key objectives of the European co-funded research project SafetyCube in order to better support evidence-based policy making. Results will be assembled in the form of a DSS that will present for each suggested road safety measure: details of risk factor tackled, measure, best estimate of casualty reduction effectiveness, cost-benefit evaluation and analytic background. The development of the DSS presents a great potential to further support decision making at local, regional, national and international level, aiming to fill in the current gap of comparable measures effectiveness evaluation. In order to provide policy-makers and industry with comprehensive and well-structured information about measures, it is essential that a systems approach is used to ensure the links between risk factors and all relevant safety measures are made fully visible. The DSS is intended to become a major source of information for industry, policy-makers and the wider road safety community.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
The study aimed at estimating the impact of pedelecs (with an assumed higher speed than bicycles) on the traffic accident severity in Germany for different penetration rates. The analysis shows that in many real situations (68%) an electrical support of bicycles has no influence on the sequence of accident events. Taking into account a number of unreported "single bicycle accidents", the adoption of similar traffic behavior and similar age distribution, the authors determined a shift of 400 former slightly to seriously injured cyclists in Germany per year. Overall this would be an increase of approximately 2.3% in case of 10% of pedelec penetration with the pessimistic assumption of 10 km/h speed increase although first natural driving studies predict a much lower average speed increase of pedelecs. The hypothesis verbalized in the initial question whether a higher distribution of pedelecs will result in more severe accidents in Germany is not verified. The study shows that electrical support didn"t result in higher collision speed in general. In many accident situations, the speed of pedelecs has only a minor influence on the accident severity. Further research focusing on a possible change of driver behavior especially in new target groups (elderly people) will be needed.
Do learner gain sufficient braking capabilities at the end of education for collision avoidance?
(2013)
The paper describes a test design to evaluate the braking behaviour in the course of the driver education. The results show that the braking capabilities increased during the driver education and the learning effects are the same for males and females. The evaluation limit is set to 6 m/s-². At the beginning of education, 50% of the drivers do not reach this limit, although the driver education car is equipped with an emergency brake assist, which is regularly installed in all vehicles since 2009. After the education, 100% of the drivers can reach the limit. The results are mapped to a collision avoidance scenario.
Driver distraction
(2017)
This report for the Institute of Advanced Motorists (IAM) summarises recent research and knowledge from scientific studies about distracted driving. The report defines what it means to be "distracted" when driving, discusses the impact of distraction on driver behaviour and safety, and what can be done to reduce distracted driving. The focus of distraction discussed here relates to how drivers engage with technology when driving. The report begins with a background to driver distraction, followed by discussion about what is actually meant by driver distraction. It is then considered why humans cannot successfully do two things at the same time, particularly within the context of driving. The subsequent section summarises the scientific research findings to date with regard to driver distraction and technology, and how this affects different types of road user. Recommendations for how driver distraction can be mitigated in the real world and a summary conclude the report. Responses to common questions raised by drivers are presented in Appendix A.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
Twenty-eight percent of traffic accidents in Japan are rear-end collisions, and of these, 13% are multiple collisions (three or more vehicles and/or roadside objects). A post-crash braking system enables the driver to stop the vehicle in a short distance after a rear-end collision to prevent secondary collisions. In this study, the effectiveness of a post-crash braking system was examined using a drive recorder database. In 64% of rear-end collisions, the driver's braking was interrupted after the collision. The stopping distance was estimated with time data from the drive recorder. We predict that the brake assist would be effective in preventing secondary collisions in 21% of cases.
A change emerges in hospital landscape due to health political measures, which in consequence also influences the pre-clinical medical care of emergencies. The main focus of this study was to gather information about emergency medical care after traffic accidents on the basis of data of Bavarian emergency medical services. In Bavaria, in 2006 it was necessary to call an emergency doctor in the case of 14.261 traffic accidents. Predominantly the patients were provided by land-based life saving appliances, air rescue services were only applied in 19.1 % of the cases. 47.6 % of patients being involved in a traffic accident were transported into a primary health care hospital. A prehospital interval of more than 60 minutes was calculated in 20 % of emergency care. 96.2 % of the patients were transported to hospitals of tertiary or maximum supply by air rescue services. The life saving appliances" readiness for action is however restricted to daylight. A further limitation appeared for routine office hours in hospitals: Only 36.7 % of accidents occurred in this time frame. An increase of hospitalizations in clinics of maximum supply appeared from 2002 until 2006 while simultaneously the prehospital period was extended. To assure a sufficient medical care of seriously injured persons further on, a fulltime and area-wide expostulation of efficient facilities is necessary. For this purpose it is necessary to establish regional trauma networks as well as emergency medical service at night time. Beyond that, a cost efficient compensation of the structural, personnel and logistic expenses has to be assured.
Although the annual traffic accident statistics published by the national police is available in public, the detailed traffic accident data has not been released in Korea. Recently the Ministry of Land, Infrastructure and Transport recognized the importance of in-depth accident data to enhance road traffic safety and initiated a research project to establish a collection of the detailed accident data. The main objective of the project is a feasibility study to establish KIDAS (Korea In-Depth Accident Study). Within this project, three university hospitals which are located in mid-size cities have been selected to collect accident data. Annually, more than 500 cases of accidents have been collected from the in-patient's interviews and diagnosis. Unlike GIDAS (German In-Depth Accident Study), currently on-site investigation can"t be performed by the Korean police. The only available data is patient medical records, patient's description of accident circumstances and the damaged vehicle. Occasionally the police provide the accident investigation reports containing very brief information on accident causation and vehicle safety. In a first step, the concept of KIDAS is to adopt the format of iGLAD (Initiative for the Global Harmonization of Accident Data) for harmonization. Since the currently collected accident information is extremely limited compared with GIDAS, the other sources of data and calculations such as KNCAP vehicle data, pc-crash simulations, vehicle registration information, insurance company data are utilized to complete the iGLAD template. Results from KIDAS_iGLAD and the cases of assessment of active safety devices such as AEBS, ESC, and LDWS will be evaluated.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
This paper will outline ETSC's contribution to the European Union's road safety policy 2011-2020. It will present some of the main recommendations from ETSC's Blueprint for the 4th Road Safety Action Programme and will introduce the response to the European Commission's Road Safety Policy Orientations 2011-2020 (published July 2010). The second framework document presented is the Transport White Paper (published March 2011). The paper will focus on new targets and the new vision set for Europe's Road Safety policy picking out some issues in particular such as traffic law enforcement and the protection of vulnerable road users. It will argue that by reinforcing the current Road Safety Policy Orientations, the EU will be better placed to reach its new ambitious goal of halving road deaths by 2020 and the longer term zero casualty vision.
Many safety-relevant tasks in control or diagnostics require binary choices such as "conflict versus separation" in air traffic control, "normal versus pathological" when interpreting x-ray pictures, or "permitted versus forbidden" when inspecting airport security scans. Deciders often are uncertain, but nevertheless required to decide between two alternatives, that is, they have not only to decide upon an action, but also about the admissible level of uncertainty. If the accepted level of judgment certainty is not taken into account, the sequence of decisions does not capture the full picture of the underlying decision process. Differences in judgment certainty are relevant, because they reflect not only the adequacy of the human-machine interface that is evaluated, but also the differences in expertise of the decider and the requirements of the actual situation or task. Therefore, capturing both judgment certainty and discrimination performance is essential. A comparison of different human-machine-interfaces (for air traffic control) is used to illustrate a methodological approach, which allows for integrated analyses of decision processes based on receiver-operator-characteristics and practical guidelines for the evaluation of human-machine-interfaces for safety-relevant operation procedures are provided.
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
The paper gives an overview of the recent (mostly 2012) figures of killed bus/coach occupants (drivers and passengers) in 27 Member States of the European Union as reported by CARE. The Evolution of the figures of bus/coach occupants killed in road accidents urban, rural without motorway and on motorways from 1991 to 2010 in 15 Member States of the EU supplements this information. More detailed are the figures reported for Germany by the Federal Statistics. The paper displays long-term evaluations (1957 to 2012) for killed, seriously and slightly injured occupants in all kinds of buses/coaches. Midterm evaluations (1995 to 2012) of the figures of fatalities and casualties are displayed for different busses according to their identification of road using as coaches, urban buses, school buses, trolley buses and "other buses". To be able to compare the evolutions of the safety of vehicle occupants it is customary to use different risk indicators. Calculations and illustrations for three often used indicators with their development over time are given: fatalities, seriously injured and slightly injured per 100,000 vehicles registered, per 1 billion (109) vehicle-kilometres travelled and per 1 billion (109) person-kilometres. These indicators are shown for occupants of cars, goods vehicles and buses/coaches. For the period from 1957 until 2012 it is obvious, that for all three vehicle categories analysed there was a clear long-term trend towards more occupant safety in terms of casualties per vehicles registered and per vehicle mileage. This was most significant for car occupants but it can be seen for bus/coach occupants and goodsvehicle occupants as well. Figures of killed occupants and of casualties related to person-kilometres are calculated and displayed for the shorter period 1995 to 2012. Here it becomes obvious that the bus/coach is still the safest mode of transport for the occupants of road vehicles. Graphs for the casualty risk indices still show significantly higher risks for car occupants despite the corresponding curve moved sustainable downwards. It is remarkable, that the risks of being killed or injured for the occupants of urban buses is growing whereas the corresponding risk for the occupants of coaches in line traffic tends downwards. The article ends with a short comparison and discussion of the risk indicators which are actually published for the occupants (driver and passengers) of cars and the passengers of buses/coaches, railroads, trams and airplanes. The interpretation of such information depends on the perception and it seems that for a complete view not only one indicator should be used and the evolutions of the indicator values during longer periods (as displayed with examples in the paper) should also be taken into account.
Data concerning accidents involving personal injury which have been collected in the context of in-depth investigations on scene in the Hannover area since 1973 and in the Dresden area since 1999 represent an important basis for empirical traffic safety research. At national and international level various analyses and comparisons are carried out on the basis of "in-depth data" from the above mentioned investigations. In-depth data play a decisive role e.g. within the validation of EuroNCAP results on secondary safety (crashworthiness) of individual passenger car models. Thus, statistically sound methods of data analysis and population parameter estimation are of high importance. Since the 1st of August 1984 the "in-depth investigations on scene" in the Hannover area have been carried out according to a sampling plan developed by HAUTZINGER in the context of a research project on behalf of BASt. In the meantime a second region of in-depth investigation on scene was added with surveys in Dresden and the surrounding area. Internationally, the acronym GIDAS (German In-Depth Accident Study) is commonly used for the two above mentioned surveys. The objective of a current research project (topic of this contribution) is, among other things, to examine and adjust the previous weighting and expansion method for the two regional accident investigations to the current general conditions.
In the context of this study, different data sources for accident research were examined regarding their possible data access and evaluated concerning the individual quality and extent of the data. Analyses of accidents require detailed and comprehensive information in particular concerning vehicle damages, injury patterns and descriptions of the accident sequence. The police documentation supplies the basic accident statistics and is amended in the context of the forensic treatment by further information, e.g. by medical and technical appraisals and witness questionings. As a new approach to the data acquisition for the analysis of fatal traffic accidents, the information was made usable which was collected by the police and by the investigations of the public prosecutor. The best strategy for obtaining reliable, extensive and complete data consists of combining the information from these two sources: the very complete, but elementary statistic data of the Niedersächsisches Landesamt für Statistik (Lower Saxony State Authority of Statistics), based on the police documentation as well as the very extensive accident information resulting from the investigation documentation of the public prosecutor after conclusion of the procedure, the so-called Court Records. Of all 715 fatal traffic accidents, which happened in the year 2003 in the German State of Lower Saxony, 238 cases were selected by means of a statistically coincidental selective procedure based on a statistically representative manner (every third accident). These cases cover the investigation documents of the 11 responsible public prosecutor- offices, which were requested and evaluated while preserving the data security. Of the 238 cases 202 cases were available, which were individually coded and stored in a data base using 160 variables. Thus a data base of a sample of representative data for fatal accidents in Lower Saxony was set up. The data base contains extensive information concerning general accident data (35 variables), concerning road and road surface data (30 variables), concerning vehicle-specific data (68 variables) as well as concerning personal and injury data (27 variables).
Today's volumes of traffic require more and more responsibility from each individual road user in their interactions. Those who drive motor vehicles have the singular obligation to minimise the risk of accidents and hence the severity of injuries, particularly with a view to the most vulnerable road users such as motor bikes, bikes and pedestrians. Since responsible and pro-active driving depends first and foremost on the visual information relayed by our eyes and the visual channel this requires good command of the traffic and all-round visibility from our driver's seat. Granted that human error can never be fully excluded, improving visibility around the car is nevertheless an urgent priority. To do so, we need to rate visibility in the most realistic driving situations. Since the existing visibility metrics and methodology are not applicable to real-life driving situations, this study aimed at developing a new visibility rating methodology based on real-life accident scenarios. On the basis of the cases documented by the accident research project, this study analysed criteria indicative of diminishing visibility on the one hand and revealing some peculiarities in connection with the visibility issue on the other. Based on the above, the project set out to develop a rating methodology allowing to assess all-round visibility in various road situations taking into account both driver and road geometries. In this context, the assessment of visibility while turning a corner, crossing an intersection and joining traffic on a major road (priority through route) is of major importance. The first tests have shown that critical situations can be avoided by adapting the relevant geometries and technical solutions and that significant improvements of road safety can be derived therefrom.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
In North America, frontal crash tests in both the regulatory environment and consumer-based safety rating schemes have historically been based on full-width and moderate-overlap (40%) vehicle to barrier impacts. The combination of improved seat-belt technologies, notably belt tensioning and load limiting systems, together with advanced airbags, has proven very effective in providing occupant protection in these crash modes. Recently, however, concern has been raised over the contribution of narrower frontal impacts, involving primarily the vehicle corners, to the incidence of fatality and serious injury as a result of the potential for increased occupant compartment intrusion and performance limitations of current restraint systems. Drawing on data documented in the National Automotive Sampling System (NASS)/ Crashworthiness Data System (CDS) for calendar years 1999 to 2012, the present study examines the characteristics of existing and proposed corner crash test configurations, and the nature of real-world collisions that approximate the test environments. In this analysis, particular emphasis is placed on crash pulse information extracted from vehicle-based event data recorders (EDR's).
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
[Introduction:] A large number of road users involved in road traffic crashes recover from their injuries, but some of them never recover fully and suffer from some kind of permanent disability. In addition to loss of life or reduced quality of life, road accidents carry many and diverse consequences to the survivors such as legal implications, economic burden, job absences, need of care from a third person, home and vehicle adaptations as well as psychological consequences. Within an EU funded project MOVE/C4/SUB/2011-294/SI2.628846 (REHABIL AID) these consequences were analyzed more detailed.
The misuse of CRS (child restraint system) is one of the most urgent problems in connection of child safety in cars. Numerous field studies show that more than two thirds of all CRS are used in a wrong way. This misuse could lead to serious injuries for the children. Surprisingly the quality of CRS use is coded much better in accident data (e.g. GIDAS) than the results of observatory field studies show. It is expected that misuse of CRS was not detected by the accident teams in a large number of the cases. An essential part in improving child seats and their usability is the knowledge of the relation between misuse and resulting injuries. For that the analysis and experimental reconstruction of accidents is an important part. For allowing an exact experimental accident reconstruction, it is necessary to have detailed information about the securing situation of the child and about the installation of the CRS in the car.
The increasing economics in India has an enormous growth of its road traffic. As observed from official Indian accident statistics the number of road fatalities are one of the highest worldwide. In contrast to most industrialized nations they have an rapidly increasing trend. To come along with this trend it becomes more than essential to understand the traffic accident situation. The official Indian accident statistics gives a glimpse of only basic information. Therefore more detailed data is needed. By using In-depth accident data and officially representative statistics the current accident situation can be evaluated in India, if a suitable weighting methodology is considered. Hence in 2009/2010 a pilot study with the collaboration partner JP-Research India pvt. Ldt. was gathered in Tamil Nadu in south of India. In-depth accident investigations were done around the Coimbatore area on four highways. At first, the collected data is evaluated. Due to consequent and continuous further development based on the first approach a methodology similar to NASS/CDS/GES in the US and GIDAS in Germany was developed. Of course all relevant accident related parameters including pictures and severity information were collected. As a matter of fact based on scaled sketches and reconstruction benefit analyses can be done in order to analyze the accident scenery in India. As a first outcome influence from infrastructure, missing education and vehicle safety were identified as key parameters in order to reduce the number of accidents and casualties. To compare the accident situation against international standards an accident classification for left hand traffic was developed based on the German Insurance classification system. Looking into detail additional accident types were identified and added to create an Indian accident type catalogue. The positive results encouraged several OEMs to participate in this investigation and together with BOSCH a consortium was established in 2010/11. Within one year from beginning in May 2011 about 200 highway accidents were collected, reported and reconstructed using the new standard. Hence a first good overview of the accident situation is available for the Coimbatore Tamil Nadu area. The major target for establishing accident investigations is the extension towards other states of India and urban areas to achieve a better overview of the accident scenery. Therefore local and national authorities have to be embedded in order to strengthen the awareness against traffic safety.
India is one of the leading countries reporting highest road accidents & related injuries. TMARG (Tata Motors Accident Research Group) has been recording crashes in association with M/s. Lokamanya Medical Foundation since 2011 with M/s, Amandeep Hospitals since Aug 2013. This study has highlighted some accident types not discussed extensively in literature. Trucks to Truck impacts " Cabin interaction with overhanging loadbody structures and Offset underside impacts for passenger vehicles are seen in significant numbers. The paper discusses these in more detail including severity.
Cyclists are more likely to be injured in fatal crashes than motorised vehicles. To gain detailed and precise behavioural data of road users, i.e. trajectories, a measuring campaign was conducted. Therefore, a black-spot for accidents with cyclists in Berlin, Germany was selected. The traffic has been detected by a fully automated traffic video analysis system continuously for twelve hours. The video surveillance system is capable of automatically extracting trajectories, classifying road user types and precise determining and positioning of conflicts and accidents. Additionally, pre-conflict and pre-accident situations could be analysed to provide further in-depth understanding of accident causation. The evaluation of the measuring campaign comprised the investigation of traffic parameters, e.g. traffic flow, as well as traffic-safety related parameters based on Surrogate Safety Measures (SSM). Furthermore, the spatial and temporal distributions of conflicts involving cyclists were determined. As a result, three possible conflict clusters could be identified, of which one cluster could be confirmed by detailed video analysis, showing conflicts caused by right turning vehicles.
As the official German catalogue of accident causes has difficulty in matching the increasing demands for detailed psychologically relevant accident causation information, a new system, based on a "7 Steps" model, so called ACASS, for analyzing and collecting causation factors of traffic accidents, was implemented in GIDAS in the year 2008. A hierarchical system was developed, which describes the human causation factors in a chronological sequence (from the perception to concrete action errors), considering the logical sequence of basic human functions when reacting to a request for reaction. With the help of this system the human errors of accident participants can be adequately described, as the causes of each range of basic human functions may be divided into their characteristics (influence criteria) and further into specific indicators of these characteristics (e.g. distraction from inside the vehicle as a characteristic of an observation-error and the operation of devices as an indication for distraction from inside the vehicle. The causation factors accordingly classified can be recorded in an economic way as a number is assigned to each basic function, to each characteristic of that basic function and to each indicator of that characteristic. Thus each causation factor can be explicitly described by means of a code of numbers. In a similar way the causation factors based on the technology of the vehicle and the driving environment, which are also subdivided in an equally hierarchical system, can be tagged with a code. Since the causes of traffic accidents can consist of a variety of factors from different ranges and categories, it is possible to tag each accident participant with several causation factors. This also opens the possibility to not only assign causation factors to the accident causer in the sense of the law, but also to other participants involved in the accident, who may have contributed to the development of the accident. The hierarchical layout of the system and the collection of the causation factors with numerical codes allow for the possibility to code information on accident causes even if the causation factor is not known to its full extent or in full detail, given the possibility to code only those cause factors, which are known. Derived from the systematic of the analysis of human accident causes ("7 steps") and from the practical experiences of on-scene interviews of accident participants, a system was set in place, which offers the possibility to extensively record not only human causation factors in a structured form. Furthermore, the analysis of the human causation factors in such a structured way provides a tool, especially for on-scene accident investigations, to conduct the interview of accident participants effectively and in a structured way.
This study analyses no.39 cases in which n.41 motorcyclists were fatally injured, or 36% of total motorcycle fatalities in Northern Ireland between 2004 and 2010 (n.114). There were n.17 cases (43.6%) where the actions of another vehicle driver caused the collision, in thirteen of these cases the motorcycles had their lights switched on. The remaining n.22 collisions (56.4%) were due to the actions of the motorcyclist. In the approach to the collision scene, there were n.13 cases (31.7%) in which the approach was a right hand bend and in n.8 (19.5%) cases, the approach was a left hand bend. In the remaining n.18 (43.9%) cases, the approach was a straight road. Of the n.17 (41.4%) motorcycles that slid after falling, n.10 (24.4%) fell onto their right side and the remaining n.7 (17.1%) fell onto their left side. The information from this study identifies primary and contributory causes of motorcycle collisions.
In the course of the EUROPEAN PROJECT TRACE all fatally injured pedestrians autopsied at the Institute for Legal Medicine in Munich in 2004 had been analysed by using the "Human Functional Failure (HFF) analysis" method. It was possible to apply this method although some restrictions have to be taken into account. The results derived from this analysis comprise first the failures the pedestrians (most often "impairment of sensorimotor and cognitive abilities") and the opponents (most often " Non-detection in visibility constraints conditions") faced in the accident, second the conflicts and tasks (pedestrian crossing the street conflicting with a vehicle from the side (which was going ahead on a straight road), the degree of accident involvement (pedestrians often the primary active part), and further the contributing factors to the accident (pedestrians most often "alcohol (> 0.05% BAC)", opponents most often "visibility constraints").
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
Bus or heavy vehicle passenger accidents are rare events, compared with car accidents, but sometimes leads to a large number of victims especially in rollover crash scenarios. Two accidents occurred in Portugal in 2007 and 2013 in which 28 people died and more than 50 are injured, shown the importance of the investigation of such accidents. For the investigation of these accidents multidisciplinary teams are constituted with engineers and police officers. All the factors involved are taken into consideration including road design, traffic signs, maintenance and hardware, human factors, and vehicle factors. In this work a methodology to an accurate collection of the data is proposed. From the information collected the accident is reconstructed using the PC-CrashTM software. From this all the contribution factors are determined and recommendations to mitigate these crashes are listed. These two accidents are rollover accidents and the analysis of the injuries and its correlation with the use of retention systems is very important. From the medical data and with the dynamics of the accident determined simulations of the occupants with biomechanical models are carried out in order to evaluate the effect of the retention systems in the injuries. This analysis is based on injury criteria (such as Abbreviated Injury Score (AIS) or Injury Severity Scale (ISS)). With this it is possible to determine if the seat belt was worn or not.
This study aimed to identify the occurrence, type and mechanisms of the traumatic injuries of the vulnerable road users in vehicle collisions, and to determine the effects of human, engineering, and environment factors on traffic accidents and injuries. The pedestrian accident cases were collected in the years 2000 to 2005 from Changsha Wujing hospital China and Accident Research Unit at Medical University Hannover in Germany. A statistic analysis was carried out using the collected accident data. The results from analysis of Changsha data were compared with results from analysis of GIDAS data Hannover. The injury severities were determined using AIS code and ISS values. The results were presented in terms of cause of injuries, injury distributions, injury patterns, injury severity. The factors influenced the injury outcomes were proposed and discussed for the vehicle transport environment and road users. The results were discussed with regard to accident data collection, accident sampling and injury distributions etc. In the urban area of Changsha, motorcycles and passenger cars are most frequently involved in vehicle pedestrian accidents. Head and lower extremities injuries are the predominant types of pedestrian injuries. The pedestrian accidents were identified as vital issue in urban traffic safety and therefore a high priority should be given to this road user group in research of safe urban transportation. In Hannover area, cars are most frequently involved in traffic accidents, injured pedestrians are involved in road traffic of Germany in 13% of all causalities only in 2005 and have nearly the same number as motorcyclists, but the half of bicyclists.
The share of high-tensile steel in car bodies has increased over the last years. While occupant safety has generally benefited from this measure, there is a potential risk that, as a result, rescue time may increase considerably. In more than 60% of all car occupant fatalities a technical rescue has been necessary. These are in particular those cases where occupants die immediately at the accident scene. Therefore, in these cases "rescue time" is a very sensitive parameter. In addition to the general analysis of the need of technical rescue and the actual rescue time depending on model years, the injury pattern of occupants requiring technical rescue will be analysed to provide advice for rescue teams. Furthermore, a detailed analysis of rescue measures for the most popular car models depending on the safety cell design is given.
Injuries in motorbike accidents in correlation with protective clothes and mechanism of the accident
(2013)
This study deals with a possible connection between safety clothing / accident mechanism and injury severity in a state-wide traffic accident investigation with focus on light and small motorbike-involvement for accidents in the area of the Saarland in which the persons riding the bike have been injured or killed. An interdisciplinary team of medical scientists and engineers collected the medical and technical data as well as all the relevant traces of the accident on scene and in time. During twenty months of data collection a total of 401 cases could be gathered. Grave injuries were more common for the group of heavier motorcycles (>125 ccm). Motorcyclists had been polytraumatized only in the group where the accident was connected with a collision. Significant correlation between protective clothes and injury severity could only be found for protective gloves and protective trousers. The knowledge about mechanism of the accident, protective clothes and severity of injuries can be helpful for the improvement of road and motorcyclists' safety.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
This study aimed at developing an injury estimation algorithm for AACN technologies for Germany and compared them to findings based on Japanese data. The data to build and to verify the algorithm was obtained from the German in-depth Accident Database (GIDAS) and split into a training and a validation dataset. Significant input variables and the generalized linear regression model to predict severe injuries (ISS>15) were selected to maximize area under the receiver operating characteristic curve (AUC). Probit regression with the input parameter multiple impact, delta v, seatbelt use and impact direction gave the largest AUC of 0.91. Sensitivity of the algorithm was validated at 90% and specificity at 76% for an injury risk threshold of 2%. It appears that no major differences between Japan and Germany exist for injury estimation based on delta v and impact direction. However, far side impact and multiple crash events appear to be associated with a larger risk increase in the German data.
Recently, EuroNCAP updated the upper legform test protocols. The main objective of this study is to establish the upper legform test in KIDAS (Korean In-depth Accident Study) taking into account domestic pedestrian accident data as well as anthropometric data to protect elderly pedestrians whose average height and weight is much smaller and lighter than other age groups, especially compared to Europeans. Therefore 230 cases of pedestrian accidents from KIDAS were investigated to explore the injury severity of body regions as well as age related injury patterns. Injuries of all body regions were examined, with a special focus on injuries of abdomen and pelvic area. On the other hand, in order to explore Korea's pedestrian accident environment, national police data and KIDAS (Korean In-depth Accident Study) data were compared. The results should be taken into account in future analyses and possible improvements, such as regulations and KNCAP test protocols, of the pedestrian safety policy in Korea.