Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (28) (entfernen)
Schlagworte
- Test method (28) (entfernen)
Institut
- Sonstige (28) (entfernen)
The Netherlands is on the way to change its existing skid resistance measuring method for its highway network from the Dutch RAW 72, a longitudinal force method, to the Sideway Force method. This method is described in the Technical Specification 15901-8 (SKM device) as well as 15901-6 (SCRIM device) and is in use in 9 European countries. The CEN TC 227 WG5 on Surface Characteristics is currently working on combining of these two technical Specifications into a European standard for Sideway-Force (SWF) measurement devices. The idea of this change in the Netherlands was perceived in 2013 and since then a lot of meetings have been held with the different Dutch decision makers as well as with countries which currently operate SWF devices. There was an intensive exchange of knowledge about these devices and their corresponding quality assurance systems, because the Netherlands wanted to incorporate and rely on an existing system of a neighbor country without losing their present level of quality. The Netherlands has therefore decided to incorporate the German SKM approach. The network monitoring with the new system will start in 2017. To ensure the quality of skid resistance measurements and further cooperation in this field, it has been decided to initiate an alliance between BASt and the Dutch road owner Rijkswaterstaat (RWS). This alliance will facilitate an exchange of research activities, calibration of the Dutch systems according to the existing German Standard as well as control measurements with a BASt-device on the Dutch network during the network monitoring. During 2016 also comparative measurements will be performed on a network level with the current Dutch device and with an SKM device to determine a conversion between the two and to be able to define new threshold values.
PROSPECT (Proactive Safety for Pedestrians and Cyclists) is a collaborative research project involving most of the relevant partners from the automotive industry (including important active safety vehicle manufacturers and tier-1 suppliers) as well as academia and independent test labs, funded by the European Commission in the Horizon 2020 research program. PROSPECT's primary goal is the development of novel active safety functions, to be finally demonstrated to the public in three prototype vehicles. A sound benefit assessment of the prototype vehicle's functionality requires a broad testing methodology which goes beyond what has currently been used. Since PROSPECT functions are developed to prevent accidents in intersections, a key aspect of the test methodology is the reproduction of natural driving styles on the test track with driving robots. For this task, data from a real driving study with subjects in a suburb of Munich, Germany was used. Further data from Barcelona will be available soon. The data suggests that intersection crossing can be broken down into five phases, two phases with straight deceleration / acceleration, one phase with constant radius and speed turning, and two phases where the bend is imitated or ended. In these latter phases, drivers mostly combine lateral and longitudinal accelerations and drive what is called a clothoid, a curve with curvature proportional to distance travelled, in order to change lateral acceleration smoothly rather than abrupt. The data suggests that the main parameter of the clothoid, the ratio distance travelled to curvature, is mostly constant during the intersections. This parameter together with decelerations and speeds allows the generation of synthetic robot program files for a reproduction of natural driving styles using robots, allowing a much greater reproducibility than what is possible with human test drivers. First tests show that in principle it is possible to use the driving robots for vehicle control in that manner; a challenge currently is the control performance of the robot system in terms of speed control, but it is anticipated that this problem will be solved soon. Further elements of the PROSPECT test methodology are a standard intersection marking to be implemented on the test track which allows the efficient testing of all PROSPECT test cases, standard mobile and light obstruction elements for quick reproduction of obstructions of view, and a concept for tests in realistic surroundings. First tests using the PROSPECT test methodology will be conducted over the summer 2017, and final tests of the prototype vehicles developed within PROSPECT will be conducted in early 2018
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
Test and assessment procedures for passive pedestrian protection based on developments by the European Enhanced Vehicle-safety Committee (EEVC) have been introduced in world-wide regulations and consumer test programmes, with considerable harmonization between these programmes. Nevertheless, latest accident investigations reveal a stagnation of pedestrian fatality numbers on European roads running the risk of not meeting the European Union- goal of halving the number of road fatalities by the year 2020. The branch of external road user safety within the EC-funded research project SENIORS under the HORIZON 2020 framework programme focuses on investigating the benefit of modifications to pedestrian test and assessment procedures and their impactors for vulnerable road users with focus on the elderly. Injury patterns of pedestrians and cyclists derived from the German In-Depth Accident Study (GIDAS) show a trend of AIS 2+ and AIS 3+ injuries getting more relevant for the thorax region in crashes with newer cars (Wisch et al., 2017), while maintaining the relevance for head and lower extremities. Several crash databases from Europe such as GIDAS and the Swedish Traffic Accident Data Acquisition (STRADA) also show that head, thorax and lower extremities are the key affected body regions not only for the average population but in particular for the elderly. Therefore, the SENIORS project is focusing on an improvement of currently available impactors and procedures in terms of biofidelity and injury assessment ability towards a better protection of the affected body regions, incorporating previous results from FP 6 project APROSYS and subsequent studies carried out by BASt. The paper describes the overall methodology to develop revised FE impactor models. Matched human body model and impactor simulations against generic test rigs provide transfer functions that will be used for the derivation of impactor criteria from human injury risk functions for the affected body regions. In a later step, the refined impactors will be validated by simulations against actual vehicle front-ends. Prototyping and adaptation of test and assessment procedures as well as an impact assessment will conclude the work of the project at the final stage. The work will contribute to an improved protection of vulnerable road users focusing on the elderly. The use of advanced human body models to develop applicable assessment criteria for the revised impactors is intended to cope with the paucity of actual biomechanical data focusing on elderly pedestrians. In order to achieve optimized results in the future, the improved test methods need to be implemented within an integrated approach, combining active with passive safety measures. In order to address the developments in road accidents and injury patterns of vulnerable road users, established test and assessment procedures need to be continuously verified and, where needed, to be revised. The demographic change as well as changes in the vehicle fleet, leading to a variation of accident scenarios, injury frequencies and injury patterns of vulnerable road users are addressed by the work provided by the SENIORS project, introducing updated impactors for pedestrian test and assessment procedures.
Supported by field accident data and monitoring results of European Regulation (EC) No. 78/2009, recent plans of the European Commission regarding a way forward to improve passive safety of vulnerable road users include, amongst other things, an extension of the head test area. The inclusion of passive cyclist safety is also being considered by Euro NCAP. Although passenger car to cyclist collisions are often severe and have a significant share within the accident statistics, cyclists are neither considered sufficiently in the legislative nor in the consumer ratings tests. Therefore, a test procedure to assess the protection potential of vehicle fronts in a collision with cyclists has been developed within a current research project. For this purpose, the existing pedestrian head impact test procedures were modified in order to include boundary conditions relevant for cyclists as the second big group of vulnerable road users. Based on an in-depth analysis of passenger car to cyclist accidents in Germany the three most representative accident constellations have been initially defined. The development of the test procedure itself was based on corresponding simulations with representative vehicle and bicycle models. In addition to different cyclist heights, reaching from a 6-year-old child to a 95%-male, also four pedal positions were considered. By reconstruction of a real accident the defined simulation parameters could be validated in advance. The conducted accident kinematics analysis shows for a large portion of the constellations an increased head impact area, which can reach beyond the roof leading edge, as well as high average values for head impact velocity and angle. Based on the simulation data obtained for the different vehicle models, cyclist-specific test parameters for impactor tests have been derived, which have been further examined in the course of head and leg impact tests. In order to study the cyclist accident kinematics under real test conditions, different full scale tests with a Polar-II dummy positioned on a bicycle have been conducted. Overall, the tests showed a good correlation with the simulations and support the defined boundary test conditions. Typical accident scenarios and simulations reveal higher head impact locations, angles and velocities. An extended head impact area with modified test parameters will contribute to an improved protection of vulnerable road users including cyclists. However, due to significantly differing impact kinematics and postures between the lower extremities of pedestrians and cyclists, these injuries cannot be addressed by the means of current test tools such as the flexible pedestrian legform impactor FlexPLI. Based on the findings obtained within the project as well as the existing pedestrian protection requirements a cyclist protection test procedure for use in legislation and consumer test programmes has been developed, whose requirements have been transferred into a corresponding test specification. This specification provides common head test boundary conditions for pedestrians and cyclists, whereby the existing requirements are modified and two parallel test procedures are avoided.
Tunnel in Spritzbetonbauweise werden in der Regel mit einem Abdichtungssystem aus Kunststoffdichtungsbahnen (KDB) gegen das anstehende Bergwasser abgedichtet. Die Tunnelabdichtungen aus KDB müssen dabei über die gesamte Nutzungsdauer des Bauwerks von in der Regel 130 Jahren zuverlässig ihre Funktion erfüllen. Ein einfacher Austausch der KDB oder der Einbau einer gleichwertigen Alternative ist in der Regel nicht, oder nur mit erheblichem Aufwand möglich. Bislang existieren national und international keine abgesicherten Prüfkriterien, die eine Bestimmung der Langzeitbeständigkeit von KDB über die geforderte Nutzungsdauer von mindestens 100 Jahren ermöglichen. Im vorliegenden Beitrag werden Untersuchungsergebnisse eines BASt Forschungsprojektes präsentiert, in dem Prüfkriterien für die Abschätzung der Langzeitbeständigkeit von KDB aus PVC-P hergeleitet werden. In diesem Projekt werden verschiedene marktübliche KDB für die Tunnelabdichtung mit einem beschleunigten Prüfverfahren "Lagerung in heißem Wasser" systematisch auf ihr Alterungsverhalten hin untersucht. Das hierfür verwendete Immersionsprüfverfahren wurde neu entwickelt und basiert auf der SIA V 280 (Prüfung Nr. 13) und DIN EN 14415. Ziel der Untersuchungen ist es, die erforderlichen Prüfkriterien zu definieren, die für eine praxisgerechte Abschätzung der Nutzungsdauer von mindestens 100 Jahren erforderlich sind. Hierfür werden beispielsweise die Einlagerungsdauer, die Einlagerungstemperatur und das Prüfmedium strukturiert untersucht. Zum Vergleich der Prüfergebnisse aus dem Immersionsprüfverfahren werden Untersuchungen an ausgebauten KDB Proben aus 2 älteren Straßentunneln herangezogen. Die Ergebnisse des Forschungsvorhabens sollen in die Fortschreibung des nationalen Regelwerks für den Straßentunnelbau (TL/TP KDB) einfließen.
Für die rechnerische Dimensionierung der Betondecken im Oberbau von Verkehrsflächen für den Neubau sowie die Erneuerung nach RDO-Beton 09 ist die statische Spaltzugfestigkeit an der unteren beziehungsweise unteren und oberen Scheibe des Betonzylinders beziehungsweise Bohrkerns entsprechend der Vorgaben der AL Sp-Beton zu bestimmen. Aufgrund der unzureichenden Kenntnis der Präzision dieses Prüfverfahrens wurden mit einem breit aufgestellten Ringversuch die statistischen Kennwerte an Labor- und Bestandsbetonen unter Vergleichs- und Wiederholbedingungen auf der Grundlage des FGSV-Merkblatts über die statistische Auswertung von Prüfergebnissen ermittelt. Für eine möglichst gute statistische Absicherung nahmen an dem Ringversuch dreizehn erfahrene Prüfstellen teil. Zur Abdeckung des vielschichtigen Einsatzes des Prüfverfahrens erfolgte der Ringversuch an acht Prüflosen. Dabei berücksichtigen einerseits die Prüflose 1 und 2 mit den im Transportbetonwerk hergestellten Betonzylindern die Erst-/Eignungsprüfung und das darauf aufbauende Prüflos 3 mit Bohrkernen aus einer im Feldversuch hergestellten Fahrbahnplatte mit gleicher Betonrezeptur die Übereinstimmungskontrolle bei Neubaumaßnahmen. Andererseits findet der Einsatz des Prüfverfahrens bei der Restsubstanzbewertung von Betonfahrbahnplatten bei den Prüflosen 4 bis 7 mit den Bohrkernen aus vier in Waschbetonbauweise ausgeführten Fahrbahnplatten Berücksichtigung. Das zusätzlich aufgenommene Prüflos 8 mit einem Labormörtel dient der Herausarbeitung des Materialeinflusses auf die Präzision der Spaltzugfestigkeitsprüfung. Zusammenfassend kann festgestellt werden, dass die Präzision der in der AL Sp-Beton beschriebenen Spaltzugfestigkeitsprüfung mit einem Variationskoeffizienten von weniger als 10 % unter Wiederhol- und Vergleichsbedingungen hinreichend genau ist. Der geringe Unterschied zwischen den Variationskoeffizienten unter Wiederhol- und Vergleichsbedingungen lässt zusätzlich den Schluss zu, dass der Einfluss des unterschiedlichen Personals und der verschiedenartigen Prüftechniken bei den einzelnen Prüfstellen relativ gering ist. Die im Rahmen des Ringversuchs gewonnenen Erkenntnisse haben bereits partiell Eingang in die Normung gefunden.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
Having a look at safety to traffic and the prevention of accidents it can be observed that technical improvements in active safety of vehicles have let to various positive effects in this area. Among other components the tyre-road-contact takes a key role in the development of active safety technologies. All forces in accelerating, breaking and vehicle guidance have to be transmitted through the tyre-road contact area by friction forces. A common way to characterize a friction process is to identify the coefficient of friction μ between two touching materials. Even though there are several approaches to experimentially characterise road surfaces, no standard method exists. In this paper an overview of existing test methods is given. Furthermore the preliminary design of a newly developed portable test device with its possibility to investigate the tyre-road-friction of arbitrary roads or even places of accidents is shown.
Automotive interiors have long been a potentially injurious impact area to occupants during accidents, especially in the absence of adequate padding. The U.S. Federal Motor Vehicle Safety Standard (FMVSS) 201, Occupant Protection in Interior Impact, outlines test procedures and performance criteria in order to mitigate potentially injurious head impacts to interior surfaces. FMVSS 201 specifies a finite set of impact locations and applies to passenger vehicles of a specified year range and with a gross vehicle weight rating less than 10,000 lb. In this paper, two head impact test methodologies are presented, a pendulum-test device and a Free Motion Headform (FMH) launching device, which allows for dynamic, repeatable impact evaluation of various vehicle interior surfaces and their impact attenuation abilities. The presented testing includes multiple series that evaluate the effect of differing vehicle upper interior padding on occupant head injury. One study in particular, analyzes a head impact to the side header of a heavy truck (not included in FMVSS 201) during a 90 degree rollover. Additionally, two other series of tests are presented which assess the injury reduction effect of side airbags to near side as well as far side occupants in a side impact scenario. Lastly, a forensic analysis is presented which evaluates two possible head impact locations experienced in a real world accident by analysis of the resulting interior compartment damage utilizing the FMH launching device test method. The data collected and presented includes accelerometer instrumentation and high speed video analysis. These studies demonstrate that adequate padding and airbags are very effective at mitigating head injury potential at impact speeds of 12-25 mph (19-40 kph).
Proposal for a test procedure of assistance systems regarding preventive pedestrian protection
(2011)
This paper is showing a proposal for a test procedure regarding preventive pedestrian protection based on accident analysis. Over the past years pedestrian protection has become an increasing importance also during the development phase of new vehicles. After a phase of focusing on secondary safety, there are current activities to detect a possible collision by assistance systems. Such systems have the task to inform the driver and/or automatically activate the brakes. How practical is such a system? In which kind of traffic situations will it work? How is it possible to check the effectiveness of such a system? To test the effectiveness, currently there are no generally approved identifiable procedures. It is reasonable that such a test should be based on real accidents. The test procedure should be designed to test all systems, independent of the system- working principle. The vFSS group (advanced Forward-looking Safety Systems) was founded to develop a proposal for a technology independent test procedure, which reflects the real accident situation. This contribution is showing the results of vFSS. The developed test procedure focuses on accidents between passenger cars and pedestrians. The results are based on analysis results of in-depth databases of GIDAS, German insurers and DEKRA and added by analysis of national and international statistics. The in-depth analysis includes many pre-crash situations with several influencing factors. The factors are e. g. speed of the car, speed of the pedestrian, moving direction and a possible obscuration of the pedestrian by an object. The results comprise also the different situations of adults and children. Furthermore, they include details regarding influence of the lighting conditions (daylight or night) especially with respect to the accident consequences. In fact, more accidents happen at daylight, but fatal accidents are more often at night. A clustering of parameter combinations was found which represents typical accident scenarios. There are six typical accident scenarios which were merged in four test scenarios. The test scenarios are varying the starting position of the pedestrian, the pedestrian size (adult or child) and the speed of the pedestrian, whereas the speed of the car will not be varied. To ensure the independency from used sensing technologies it is necessary to use a suitable dummy. For example, if sensors are based on infrared, the dummy should emit the temperature of a human being. The test procedure will identify the collision speed as the key parameter for assessing the effectiveness of the tested system. The collision speed is defined as the reduction between initial test speed of the car and impact speed. The assessment of the speed reduction value regarding the safety benefit, however, will be part of a separate procedure.
Im Rahmen eines von der Bundesanstalt für Straßenwesen (BASt) initiierten Forschungsvorhabens (15.449/2007/ERB: "Prüfverfahren zur Beurteilung der Lebensdauer von Kunststoffdichtungsbahnen für Straßentunnel") wurden anhand von Untersuchungen an Kunststoffdichtungsbahnen (KDB) auf Basis von Polyolefinwerkstoffen die Möglichkeiten der Beurteilung der oxidativen Langzeitbeständigkeit sondiert. Im Mittelpunkt stand die Erprobung des Autoklaventests in Anlehnung an DIN EN ISO 13438 (Methode C1/C2) an ausgewählten, für den Tunnelbau repräsentativen marktüblichen KDB-Produkten. Die Untersuchungen im Autoklaven bei erhöhten Temperaturen (60 -°C, 70 -°C und 80 -°C) und Sauerstoffdrücken (11, 21 und 51 bar) wurden durch vergleichende Versuche im Wärmeschrank (Ofen) bei erhöhter Temperatur (85 -°C) in Anlehnung an DIN EN 14575 ergänzt. Die KDB-Produkte wurden außerdem einer eingehenden Materialcharakterisierung (Zugprüfung, OMA, DSC) unterzogen. Weiterhin wurden Bauwerksdaten recherchiert und auf ihre Nutzbarkeit zur Bewertung und Prüfbarkeit der Langzeitbeständigkeit von KDB in Tunneln betrachtet. Ziel war auch, die Anwendbarkeit des bisher vorgeschlagenen Extrapolationsmodells zur Auswertung der Ergebnisse von Autoklaventests an im Tunnelbau marktüblichen Produkten für Nutzungsdauern über 25 Jahre zu überprüfen und zur Entwicklung eines geeigneten Prüfverfahrens beizutragen. Der Beitrag geht auf Ergebnisse des Vorhabens ein und zeigt erste Schlussfolgerungen und weiteren Untersuchungsbedarf auf. Die Ergebnisse werden in den "Empfehlungen zu Dichtungssystemen im Tunnelbau EAG-EDT" des Arbeitskreises 5.1 "Kunststoffe in der Geotechnik und im Wasserbau" berücksichtigt, deren 2. Auflage in Vorbereitung ist. Aspekte des thermischen Verhaltens der eingesetzten Werkstoffe sowie mögliche Anpassungen der Prüfrandbedingungen für die Autoklaventests werden ergänzt und Hinweise zur Interpretation von Prüfergebnissen gegeben. Außerdem wurden inzwischen ausgehend von den Ergebnissen des Forschungsvorhabens erste Autoklaven-Ringversuche in drei Prüfinstitutionen initiiert.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
Zur Ergänzung der bestehenden Routineverfahren in der forensischen Blutalkoholanalytik wurde ein massenspektrometrisches Verfahren mit d6-Ethanol als internem Standard entwickelt. Ziel war die Anwendung eines beweissicheren Bestimmungsverfahrens, bei dem Ethanol über die Retentionszeit und Substanzeigenschaften identifiziert wird. Die Pilotstudie belegt, dass die forensische Blutalkoholbestimmung durch Anwendung eines gaschromatographischen und massenspektrometrischen Verfahrens mit Dampfraumanalyse routinemäßig möglich ist. Im Gegensatz zum GC- und ADH-Verfahren ist die massenspektrometrische Blutalkoholbestimmung beweissicher. Die Autoren empfehlen die Aufnahme in die Richtlinien zur Bestimmung der Blutalkoholkonzentration für forensische Zwecke. Die Arbeit wurde vom Bund gegen Alkohol und Drogen im Straßenverkehr e.V. (B.A.D.S.) unterstützt.
Diese Studie erfolgte als eine erste Prüfung der Frage, ob 0,1 Promille als Sicherheitszuschlag für eine Bestimmung eines Blutalkoholwertes von 0,1 Promille aus Gründen der Messunsicherheit angebracht und ausreichend ist. Beides trifft zu. Obwohl zur Zeit der Studie noch nicht bei oder unter 0,2 Promille kalibriert wurde, bestimmten alle Labors eine Blutalkoholkonzentration von 0,08 Promille mit einem Wert unter 0,18 g/L (Cmax ADH: 0,15 g/L = CmaxGC: 0,15 g/L = Blutalkoholkonzentration (BAK) von 0,12 Promille). Es bestand kein Bias zwischen beiden Verfahren. Festgestellte Standabweichungen: ADH: 0,021 g/L, GC: 0,025 g/L. Ein Sicherheitszuschlag von 0,1 Promille auf 0,1 Promille umfasst demnach vier Standardabweichungen und bietet für die neue Regelung im Paragrafen 24 Straßenverkehrsgesetz (StVG) bei der richtliniengemäß ausgeführten forensischen Blutalkoholbestimmung genügend Analysensicherheit.
Die Begutachtung der Fahreignung beinhaltet in Deutschland neben einer medizinischen Untersuchung und einer psychologischen Exploration gegebenenfalls auch die Anwendung anlassbezogener verhaltenswissenschaftlicher/psychologischer Testverfahren. Diese stellen keine isolierte Maßnahme dar, sondern sind Bestandteil eines Begutachtungsprozesses. Dabei stellt der sachgerechte Gebrauch von so genannten Grenzwerten unter Berücksichtigung der Einzelfallgerechtigkeit und der Einhaltung des Grundsatzes der Verhältnismäßigkeit eine unabdingbare Voraussetzung dar. Testwerte sind nicht absolut, sondern relativ und üben von daher einen eher geringen Einfluss auf das Gutachtenergebnis in Bezug auf eine Prognose des Verkehrsverhaltens aus. Im Bereich des Verkehrsverhaltens kommt es nicht entscheidend darauf an, ob eine im Milli- oder Nanobereich exakte Messgenauigkeit erreicht wird, sondern wie die verkehrsmedizinischen, verkehrspsychologischen, technischen und anderen Sachverständigen mit dem Messwert fachlich umgehen. So müssen im Bereich der Begutachtung der Fahreignung tätige psychologische und medizinische Sachverständige in der Lage sein, Befunde im Einzelfall fehler-, mangel- sowie widerspruchsfrei zu interpretieren. Dies beinhaltet auch, sich mit den Ergebnissen eines psychologischen Testverfahrens fach- und sachgerecht auseinanderzusetzen, nach Kompensationsmöglichkeiten zu suchen und gegebenenfalls eine psychologische Fahrverhaltensbeobachtung durchzuführen. Bei grenzwertigen Vorgaben handelt es sich nicht um "Cut-Offs", sondern um "kritische Grenzwerte", die im Zusammenhang mit mehreren anderen Faktoren zu werten sind.
Die aktuellen Richtlinien zur Bestimmung der Blutalkoholkonzentration (BAK) für forensische Zwecke (BAK-Richtlinie, 2007) lassen unter bestimmten Bedingungen auch zwei verschiedene gaschromatographische Analysen anstatt der häufig angewandten Kombination Gaschromatographie und enzymatische Methode ADH zur Bestimmung des Blutalkoholgehaltes zu. Untersucht wurde die Messpräzision zweier gaschromatographischer Verfahren bei der Alkoholanalytik im Vergleich zur häufiger angewandten Methodenkombination. In mehr als 50 Prozent der Fälle hat sich bei den verglichenen Methodenkombinationen ein identischer Mittelwert ergeben. Ansonsten waren die Abweichungen gering. Damit werden die hohen Anforderungen, die an die forensische Blutalkoholbestimmung gestellt werden, durch die modernen Laborautomaten erfüllt.
Der Beitrag berichtet in einem ersten Teil über die in den Niederlanden angewendeten Inspektionstechniken zur Feststellung von Schäden (Rissen) bei orthotropen Stahlfahrbahnplatten und in einem zweiten Teil über die Instandsetzung der Moerdijkbruecke mit einer zusätzlichen Deckschicht aus bewehrtem hochfesten Stahlfaserbeton. Die Ausführungen zu den Inspektionstechniken umfassen die visuelle Inspektion, magnetische Inspektion, Farbeindringprüfung, Ultraschallprüfung und Diffraktionseffekt bei Anstrahlen von Fehlern (Time of Flight Diffraction (TOFD)) sowie radiographische Untersuchungen und das Wirbelstromverfahren. Für jede dieser Methoden wird ihre Wirkungsweise, Handhabung und der Anwendungsbereich angegeben. Die Moerdijkbrücke ist eine der meistbefahrenen Brücken in den Niederlanden mit einem erheblichen Schwerverkehrsaufkommen und weist etliche Schäden am Deckblech auf. Die bisher durchgeführte Instandsetzung durch Ausbessern der Längsschweissnähte führte nicht zum erhofften Erfolg. Der Bauherr entschloss sich daher, die Gussasphaltschicht durch einen bewehrten hochfesten Stahlfaserbeton mit einer Dicke von 5 cm mit Verbund zum Stahldeckblech zu ersetzen. Die Spannungen im Deckblech konnten auf diese Weise um einen Faktor 4 bis 5 reduziert werden. Die Methode reagiert jedoch empfindlich auf Abweichungen der Mischungsverhältnisse des Betons und der Viskosität.
Im Oktober 2007 wurde die Rügenbrücke, eine der längsten Hochbrücken Europas, für den Verkehr freigegeben. Der Beitrag befasst sich mit den Erfahrungen, die bei Planung und Bau dieses bemerkenswerten Bauwerks gemacht wurden, insbesondere hinsichtlich der vielen bautechnischen Innovationen bei dem Schlüsselbauwerk des Brückenzuges, der 570 m langen Schrägseilbrücke über den Ziegelgraben. Eine der wesentlichen Erstanwendungen für Deutschland betraf die Ausführung der Schrägseile mit Litzenbündeln des Systems DYNA Grip der SUSPA DSI. Wegen des aus Gründen des Vogelschutzes erforderlichen Mindestdurchmessers der Seile von 12 cm waren vollverschlossene Seile aus ingenieurtechnischen und wirtschaftlichen Gründen benachteiligt, sodass sich der Bauherr für Seile aus Litzenbuendeln entschied. Die Schrägseilbrücke über den Ziegelgraben wird schon jetzt als modernes Wahrzeichen der Stadt Stralsund empfunden. Sie passt sich gestalterisch hervorragend in die Umgebung ein und beeinträchtigt auch nicht die zum Weltkulturerbe zählende Altstadt von Stralsund. Besonders besticht das Bauwerk durch seine Leichtigkeit und die Einpassung der Formen der Bauteile, zum Beispiel wegen der tropfenfoermigen Gestaltung des Pylons und der Pfeiler, in das maritime Umfeld. Da die verwendeten Schrägseil-Litzenbündel noch nicht allgemein bauaufsichtlich zugelassen sind, kam der Qualitätssicherung für die Seile in allen Stufen der Planung, Fertigung, Montage und Bauwerksprüfung eine herausragende Bedeutung zu. Der zugehörige Qualitätssicherungsplan wird im Bericht ausführlich mit den wesentlichen \"schrägseilspezifischen\" Maßnahmen beschrieben. Schwingungen und Ermüdungsbeanspruchungen der Seile durch Fahrverkehr und Wind liessen sich durch einen mehrstufigen, kontinuierlich verdichteten Planungsprozess unter Nutzung von Versuchsdaten und Messungen am Bauwerk wirkungsvoll beherrschen. Aus Sicht der Bauwerksprüfung bestanden anfänglich Bedenken wegen der Erreichbarkeit der bis in 80 m Höhe über dem Brückendeck gespannten Schrägseile und der nicht direkt zugänglichen Litzen innerhalb des Hüllrohres sowie der Verankerungen. Daher wurden alle verfügbaren Prüfverfahren für Schrägseile an der Rügenbrücke getestet. Daraus ergab sich eine Prüfmatrix aus Prüfverfahren, Prüfmittel und Prüfumfang für die gesamte Nutzungsdauer. Zusammenfassend wird festgestellt, dass bei der Ziegelgrabenbrücke Schrägseile aus Litzenbündeln eine den vollverschlossenen Seilen ebenbürtige Bauart darstellen.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
The Swedish National Road Administration (SNRA), the Japanese Automobile Research Institute (JARI) and the Federal Highway Research Institute (BASt) are co-operating in the International Harmonized Research Activities on Intelligent Transportation Systems (IHRA-ITS). Under this umbrella a joint study was conducted. The overall objective of this study was to contribute to the definition and validation of a "battery of tools" which enables a prediction and an assessment of changes in driver workload due to the use of in-vehicle information systems (IVIS) while driving. In this sense \"validation\" means to produce empirical evidence from which it can be concluded that these methods reliably discriminate between IVIS which differ in terms of relevant features of the HMI-design. Additionally these methods should also be sensitive to the task demands imposed on the driver by the traffic situation and their interactions with HMI-design. To achieve these goals experimental validation studies (on-road and in the simulator) were performed in Sweden, Germany and Japan. As a common element these studies focused on the secondary task methodology as an approach to the study of driver workload. In a joint German-Swedish on-road study the Peripheral Detection Task (PDT) was assessed with respect to its sensitivity to the complexity of traffic situations and effects of different types of navigation systems. Results show that the PDT performance of both the German and the Swedish subjects reflects the task demands of the traffic situations better than those of the IVIS. However, alternative explanations are possible which will be examined by further analyses. Results of this study are supplemented by the Japanese study where informational demands induced by various traffic situations were analysed by using a simple arithmetic task as a secondary task. Results of this study show that relatively large task demands can be expected even from simple traffic situations.
When the EEVC proposed the full-scale side impact test procedure, it recommended that consideration should be given to an interior headform test in addition. This was to evaluate areas of contact not assessed by the dummy. EEVC Working Group 13 has been researching the parameters of a possible European headform test procedure in four phases. Earlier stages of the research have been presented at previous ESV conferences. The conclusions from these have suggested that the US free motion headform should be used in any European test procedure and that it should be a free flight test, not guided. This research has now culminated in proposals for a European test procedure. This paper presents the proposed EEVC side impact interior headform test procedure, giving the rationale for the test and the first results from the validation phase of the test protocol.
Despite the steadily declining number of pedestrian fatalities and injuries in most European countries during recent decades, pedestrian protection is still of great importance in the European Union as well as in Germany. This is because they still constitute a large proportion of road user casualties and are more likely to suffer serious and fatal injuries than most other road users. In 1999 only car occupants suffered more fatal injuries than pedestrians in Germany. In December 1998, EEVC WG 17 completed their review and updating of the EEVC WG 10 pedestrian test procedure that made it possible to evaluate the protection afforded to pedestrians by the front of passenger cars in an accident. Within the scope of this procedure, four different impactors are used representing those parts of the body which are injured very often and/or very seriously in vehicle-pedestrian-collisions. In a project executed by IKA and BASt, a small family car was tested according to the EEVC WG 17 test procedure. Afterwards modifications to the car were carried out in order to improve the pedestrian protection provided by the vehicle design. There were certain restrictions placed on the level of modifications undertaken, e.g. only minor modifications to vehicle styling and to the vehicle structures, which provide passenger protection. The redesigned vehicle was tested again using the WG 17 test procedure. The test results of the modified vehicle were compared with those of the standard vehicle and evaluated. The results show that considered measures for pedestrian protection in many areas of the vehicle front structure and the use of innovative techniques can lead to a significant reduction of the loads of pedestrians at an acceptable expense.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.