Sonstige
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx. However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My. The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was observed. It was also observed that the primary neck response in these tests was flexion, not extension. This correlates well with recent findings from Japan and the United States showing a correlation between neck flexion and injury in accident replication simulations and postmortem human subjects (PMHS) studies, respectively. The present certification tests may not adequately control front cervical spine bumper characteristics, which are important for neck flexion response. The certification sled test also does not include the pelvis and so cannot be used to control pelvis response and does not substantially load the lumbar bumpers and so does not control these parts of the dummy. The stiffness of all spine bumpers and of the pelvis flesh should be much more tightly controlled. It is recommended that a method for certifying the front cervical bumpers should be developed. Recommendations are also made for tighter tolerance on the input parameters for the existing certification tests.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
To improve vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility aims to improve both the self and partner protection properties of vehicles. Although compatibility has received worldwide attention for many years, no final assessment approach has been defined. Within the Frontal Impact and Compatibility Assessment Research (FIMCAR) project, different frontal impact test procedures (offset deformable barrier [ODB] test as currently used for Economic Commission for Europe [ECE] R94, progressive deformable barrier test as proposed by France for a new ECE regulation, moveable deformable barrier test as discussed worldwide, full-width rigid barrier test as used in Federal Motor Vehicle Safety Standard [FMVSS] 208, and full-width deformable barrier test) were analyzed regarding their potential for future frontal impact legislation. The research activities focused on car-to-car frontal impact accidents based on accident investigations involving newer cars. Test procedures were developed with both a crash test program and numerical simulations. The proposal from FIMCAR is to use a full-width test procedure with a deformable element and compatibility metrics in combination with the current offset test as a frontal impact assessment approach that also addresses compatibility. By adding a full-width test to the current ODB test it is possible to better address the issues of structural misalignment and injuries resulting from high acceleration accidents as observed in the current fleet. The estimated benefit ranges from a 5 to 12 percent reduction of fatalities and serious injuries resulting from frontal impact accidents. By using a deformable element in the full-width test, the test conditions are more representative of real-world situations with respect to acceleration pulse, restraint system triggering time, and deformation pattern of the front structure. The test results are therefore expected to better represent real-world performance of the tested car. Furthermore, the assessment of the structural alignment is more robust than in the rigid wall test.
For the assessment of vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility compromises both the self protection and the partner protection properties of vehicles. For the accident data analysis, the CCIS (GB) and GIDAS (DE) in-depth data bases were used. Selection criteria were frontal car accidents with car in compliance with ECE R94. For this study belted adult occupants in the front seats sustaining MAIS 2+ injuries were studied. Following this analysis FIMCAR concluded that the following compatibility issues are relevant: - Poor structural interaction (especially low overlap and over/underriding) - Compartment strength - Frontal force mismatch with lower priority than poor structural interaction In addition injuries arising from the acceleration loading of the occupant are present in a significant portion of frontal crashes. Based on the findings of the accident analysis the aims that shall be addressed by the proposed assessment approach were defined and priorities were allocated to them. The aims and priorities shall help to decide on suitable test procedures and appropriate metrics. In general it is anticipated that a full overlap and off-set test procedure is the most appropriate set of tests to assess a vehicle- frontal impact self and partner protection.
Since a number of human models have been developed it appears sensible to use these models also in the accident analysis. Especially the understanding of injury mechanisms and probably even injury risk curves can be significantly improved when interesting accidents are reconstructed using human body models. However, an important limitation for utilising human models for accident reconstruction is the effort needed to develop detailed FE models of the accident partners or to prepare the human model reconstruction by running physical accident reconstructions. The proposed approach for using human models for accident reconstruction is to use simplified and parametric car models. These models can be adapted to the crash opponents in a fast and cost effective way. Although, accuracy is less compared to detailed FE models, the relevant change in velocity can be simulated well, indicating that the computation of a detailed crash pulse is not needed. Two frontal impact test accidents that were reconstructed experimentally and using the parametric car models are indicating sufficient correlation of the adapted parametric car models with the full scale crash reconstructions. However, further developments of the parametric models to be capable for the use in lateral impacts and rear impacts are needed. For the PC Crash simulation runs the output sampling rate is too large to allow sufficient analysis. In addition the performance appears to be too general.
Although the statistics show a decreasing rate of child injuries and fatalities in German road accidents more efforts can be made to protect children in cars e.g. by developing appropriate child restraint systems. An important part in of this work can be achieved with the help of crash tests using child dummies. However these crash tests cannot completely reflect the situation of real world crashes as factors like children moving out of the optimal position or children incorrectly fastened by their parents are difficult to predict. Therefore this study gives an overview over the current accident and injury situation of child occupants in cars in German road accidents.
Wegen der wachsenden Verbreitung von Fahrradanhängern zum Kindertransport und der möglichen Unfallgefährdung ist im vorliegenden Forschungsprojekt deren passive Sicherheit untersucht worden. Zudem wurde der Frage nachgegangen, ob der Transport von Kindern im Fahrradanhänger sicherer ist als mit dem Fahrrad mit Kindersitzen. In Absprache mit Herstellern und Vertreibern wurden verschiedene Untersuchungen durchgeführt. Es handelte sich um Anprallversuche (Anfahrversuche), Rollwagenversuche (Schlittenversuche) sowie Kopffreiheitsprüfungen und Fallversuche. Bei den Versuchen waren die Prüfobjekte mit einem oder zwei Dummies besetzt, die mit Messdatenaufnehmern ausgestattet waren. Verschiedene Messdaten, zum Beispiel Kopf- und Brustbeschleunigung, wurden erfasst und ausgewertet. Zusätzlich wurde das Kopfschutzkriterium (HPC) berechnet und bewertet. Entstandene Schäden an den Prüfobjekten wurden aufgenommen und durch Fotos dokumentiert. Die Versuchsabläufe selbst wurden mit Hochgeschwindigkeitskameras aus verschiedenen Positionen aufgezeichnet. Beim Anfahrversuch mit einem Pkw gegen ein Gespann aus Fahrrad und Anhänger waren direkte Anstöße der Anhängerinsassen an die Pkw-Front zu erkennen. Die Beschleunigungswerte waren dabei relativ hoch. Anstöße gegen Anhängerinnenteile waren bei fast allen Versuchen zu beobachten. Teilweise wurden Radaufhängungen und Radnaben beschädigt. Durch die Rollwagenversuche wurden konstruktive Schwächen bei den Sitzen und Rückhaltesystemen festgestellt. Nähte, Befestigungen und Verstellösen wurden zerstört. Es stellte sich heraus, dass die Qualität des Gurtsystems, die Steifigkeit des Anhängeraufbaus, die Sitzposition der Kinder und die vorhandene Kopffreiheit ausschlaggebend für das Verletzungsrisiko der Insassen sind. Bei den Versuchen mit Fahrradsitzen ergaben sich hohe Beschleunigungswerte durch den direkten Kontakt des Radfahrers mit der Fahrzeugfront und/oder der Fahrbahn. Das Gewicht des Radfahrers, des Fahrrades und auch Fahrradteile bergen ein erhöhtes Verletzungsrisiko für das Kind. Zusätzlich besteht die Gefahr überfahren zu werden, wenn das Kind nach dem Sturz des Fahrrades ungeschützt auf der Fahrbahn liegt. Ein direkter Vergleich der beiden Transportmöglichkeiten war aufgrund der geringen Daten der Versuche mit Fahrradkindersitzen nur bedingt möglich. Tendenziell ist der Transport der Kinder im Fahrradanhänger als weniger gefährlich zu bewerten. Es werden die Vor- und Nachteile dargestellt. Zur Bewertung der Sicherheit von Fahrradanhängern wurden die folgenden Prüfmethoden erarbeitet: - Pendelschlagprüfung für die gesamte Chassisstruktur; - Kopffreiheitsprüfung; - Belastungsprüfung der Aufbaustruktur; - Festigkeitsprüfung der Gurtsysteme. Die Prüfungen sind so aufgebaut, dass sie mit einfachen Mitteln durchzuführen sind. Es sollte somit jedem Anhängerhersteller möglich sein, die passive Sicherheit seiner Produkte umfassend zu untersuchen. Die Prüfverfahren für die Sicherheitsbewertung sollen in eine DIN-Norm und in das Merkblatt für Fahrradanhänger einfließen. Der Original-Forschungsbericht enthält einen umfangreichen Fotoband zu den Einzelheiten der Versuche und Versuchsaufbauten sowie zu den Beschädigungen der Prüfobjekte und kann bei der BASt eingesehen werden.
Sicherheitstechnische Anforderungen an die Bestuhlung moderner Reisebusse als Rückhaltesysteme
(1991)
Die Schutzfähigkeit von KOM-Fahrgastsitzen, die den ECE-R 80-Anforderungen entsprechen, ist bisher nur für die aufgerichtete Rückenlehne nachgewiesen. Hier wurde untersucht, ob auch geneigte Rückenlehnen ausreichende Schutzwirkung bieten. Ausgehend von der Normalsitzposition verfügen Reisebussitze heutiger Bauart über einen Lehnenverstellwinkel von circa 15 Grad (Normal-, Ruhesitzposition). Sondersitze für Ältere und Sportler erlauben auch die Liegesitz- beziehungsweise Liegeposition bei jedoch erheblich größeren Sitzteilern. In Schlittenaufprallversuchen mit je zwei instrumentierten anthropometrischen Messpuppen auf Reisebus-Doppelsitzen wurden die Belastungsverhältnisse eines frontalen Aufpralls simuliert. Die Lehnenverstelleinrichtung der Prüfsitze wurde behelfsweise so verändert, dass 3 (4) Winkeleinstellungen der Lehnenneigung möglich waren. Für jeweils zwei hintereinander zugeordnete Sitzplätze wurden wechselweise diese Lehneneinstellungen variiert. Mit 17 Doppelsitzen wurden insgesamt 32 Körperaufprallereignisse in den verschiedenen Lehnenneigungskonfigurationen durchgeführt. Die Versuchsergebnisse gliederten sich nach der Bewegungsform des Dummy, seinen Belastungen und den am Vordersitz hervorgerufenen Beschädigungen. Die Aufprallverhältnisse in aufrechter Normalsitzposition entsprechend der ECE-R 80 bildeten die Bewertungsbasis. Die gewonnenen Versuchsergebnisse lassen sich wie folgt zusammenfassen: - Für beliebige Lehneneinstellungen im Winkelbereich bis zu 30 Grad zur Senkrechten bietet die vorgebaute Sitzlehne generell ausreichende Rückhaltewirkung beim Körperaufprall. - Wenn die Vordersitzlehne jedoch steiler eingestellt ist als es der Körperhaltung des dahintersitzenden Dummy entspricht, ist mit 1,5-2fach höheren Kopfbelastungen zu rechnen. Das ECE-R 80-Schutzkriterium HAC < 500 wird überschritten. - Vorsorglich sollte aus sicherheitstechnischer Sicht der zulässige Grenzwinkel der Lehnenneigung auf 30 Grad zur Senkrechten beschränkt werden.
The main objective of EC CASPER research project is to reduce fatalities and injuries of children travelling in cars. Accidents involving children were investigated, modelling of human being and tools for dummies were advanced, a survey for the diagnosis of child safety was carried out and demands and applications were analysed. From the many research tasks of the CASPER project, the intention of this paper is to address the following: • In-depth investigation of accidents and accident reconstruction. These will provide important points for the injury risk curve, in order to improve it. Different accident investigation teams collected data from real road accidents, involving child car passengers, in five different European countries. Then, a selection of the most appropriate cases for the injury risk curve and the purposes of the project was made for an in-depth analysis. The final stage of this analysis was to conduct an accident reconstruction to validate the results obtained. The in-depth analysis included on-scene accident investigation, creating virtual simulations of the accident/possible reconstruction, and conducting the reconstruction. In the cases of successful reconstructions, new points were introduced to the injury risk curves. Accident reconstructions of selected cases were carried out in test laboratories as the next step following in-depth road accident investigation. These cases were reconstructed using similar child restraint systems (CRS) and the same type make and model as in the real accidents. Reconstructing real cases has several limitations, such as crash angle, cars" approximation paths and crash speed. However, a few changes and applications on the testing conditions were applied to reduce the limitations and improved the representations of the real accidents. After conducting the reconstructions, a comparison between the deformations of the cars on the real accident and the vehicles from the reconstructions was made. Additionally, a correlation between the data captured from the dummies and the injury data from the real accident was sought. This finalises an in-depth analysis of the accident, which will provide new relevant points to the injury risk curve. The CASPER project conducted a large research programme on child safety. On technical points, a promising research area is the developing injury risk curves as a result of in-depth accident investigations and reconstructions. This abstract was written whilst the project was not yet finished and final results are not yet known, but they will be available by the time of the conference. All the works and findings will not necessarily be integrated in the industrial versions of evaluation tools as the CASPER project is a research program.
Automotive interiors have long been a potentially injurious impact area to occupants during accidents, especially in the absence of adequate padding. The U.S. Federal Motor Vehicle Safety Standard (FMVSS) 201, Occupant Protection in Interior Impact, outlines test procedures and performance criteria in order to mitigate potentially injurious head impacts to interior surfaces. FMVSS 201 specifies a finite set of impact locations and applies to passenger vehicles of a specified year range and with a gross vehicle weight rating less than 10,000 lb. In this paper, two head impact test methodologies are presented, a pendulum-test device and a Free Motion Headform (FMH) launching device, which allows for dynamic, repeatable impact evaluation of various vehicle interior surfaces and their impact attenuation abilities. The presented testing includes multiple series that evaluate the effect of differing vehicle upper interior padding on occupant head injury. One study in particular, analyzes a head impact to the side header of a heavy truck (not included in FMVSS 201) during a 90 degree rollover. Additionally, two other series of tests are presented which assess the injury reduction effect of side airbags to near side as well as far side occupants in a side impact scenario. Lastly, a forensic analysis is presented which evaluates two possible head impact locations experienced in a real world accident by analysis of the resulting interior compartment damage utilizing the FMH launching device test method. The data collected and presented includes accelerometer instrumentation and high speed video analysis. These studies demonstrate that adequate padding and airbags are very effective at mitigating head injury potential at impact speeds of 12-25 mph (19-40 kph).
Event data recorders (EDRs) are a valuable tool for in-depth investigation of traffic accidents. EDRs are installed on the airbag control module (ACM) to record vehicle and occupant information before, during, and after a crash event. This study evaluates EDR characteristics and aims at better understanding EDR performance for the improvement of accident reconstruction with more reliable and accurate information regarding accidents. The analysis is based on six crash tests with corresponding EDR datasets.
When the EEVC proposed the full-scale side impact test procedure, it recommended that consideration should be given to an interior headform test in addition. This was to evaluate areas of contact not assessed by the dummy. EEVC Working Group 13 has been researching the parameters of a possible European headform test procedure in four phases. Earlier stages of the research have been presented at previous ESV conferences. The conclusions from these have suggested that the US free motion headform should be used in any European test procedure and that it should be a free flight test, not guided. This research has now culminated in proposals for a European test procedure. This paper presents the proposed EEVC side impact interior headform test procedure, giving the rationale for the test and the first results from the validation phase of the test protocol.
An approach to the standardization of accident and injury registration systems (STAIRS) in Europe
(1998)
STAIRS is a European Commission funded study whose aim is to produce a set of guidelines for a harmonised, crash injury database. The need to evaluate the effectiveness of the forthcoming European Union front and side impact directives has emphasised the need for real world crash injury data-sets that can be representative of the crash population throughout Europe. STAIRS will provide a methodology to achieve this. The ultimate aim of STAIRS is to produce a set of data collection tools which will aid decision making on vehicle crashworthiness as well as providing a means to evaluate the effectiveness of safety regulations. This paper will disseminate the up-to-date findings of the group as they try to harmonise their methods. The stage has been reached where studies into the diverse methods of the UK, French and German systems of crash injury investigation have been undertaken. An assessment has already been made of the relationships between the three current systems in order to define the areas of agreement and divergence. The conclusions reached stated that there were many areas that are already closely related and that the differences were only at the detailed level. With the emphasis on secondary safety and injury causation, core data sets were decided upon, taking into account: vehicle description, collision configuration, structural response of vehicles, restraint and airbag performance, child restraint performance, Euro NCAP, pedestrian and vehicle occupant kinematics, injury description and causation. Each variable was studied objectively, the important elements isolated and developed into a form that all partners were agreeable on. A glossary of terms is being developed as the project progresses which includes ISO standards and other definitions from the associated CAREPLUS project, which addresses the comparability of national data sets. A major consideration of the group was the data collection method to be employed. The strengths and weaknesses of each study were investigated to obtain a clear idea of which aspects offered the best way forward. The quality of this information and transference into a common format, as well as the necessary error checking systems to be employed have just been completed and are described. In tandem with this area of study the problem of the statistical relationship of each sample to the national population is also being investigated. The study proposes a mechanism to use a sample of crash injury data to represent the national and international crash injury problem
Females sustain Cervical Spine Distortion injury (CSD) more often than males. Most work dealing with the biomechanics background (e.g. injury mechanism/criteria) as well as the application in seat design/testing, focuses on the occupant model of an average male. Therefore the EU-Project ADSEAT (Adaptive Seat to Reduce Neck Injuries for Female and Male Occupants) is aimed at adding a female model for gender balanced research of CSD and improving seat design. An extensive literature review, searching for risk factors and injury criteria for males and females, was accompanied by the evaluation of different databases containing CSD cases. The database evaluations suggests that an anthropometry quite close to the 50%ile female anthropometry as known from crash test dummy design is appropriate. The results presented here form the basis for the future development of a computational female model and the improvement of seat design for better protection of both males and females in the frame of the ADSEAT-Project.
Small overlap frontal crashes are defined by a damage pattern with most of the vehicle deformation concentrated outboard of the main longitudinal structures. These crashes are prominent among frontal crashes resulting in serious and fatal injuries, even among vehicles that perform well in regulatory and consumer information crash tests. One of the critical aspects of understanding these crashes is knowing the crash speeds that cause the types of damage associated with serious injuries. Laboratory crash tests were conducted using 12 vehicles in three small overlap test conditions: pole, vehicle-to-vehicle collinear, and vehicle-to-vehicle oblique (15-degree striking angle). Field reconstruction techniques were used to estimate the delta V for each vehicle, and these results were compared with actual delta V values based on vehicle accelerometer data. Estimated delta Vs were 50% lower than actual values. Velocity change estimates for small overlap frontal crashes in databases such as NASS-CDS significantly underestimate actual values.
Event Data Recorder (EDR) is an additional function installed in airbag control module (ACM) to record vehicle and occupant information for a brief period of time before, during, and after a crash event. EDRs are now being installed in ACMs by several automakers in the USA and in Japan. The aim of this study is to understand the performance of EDRs for the improvement of accident reconstruction with more reliable information. In the first report of the study, data obtained from EDRs of seven vehicle types were evaluated using 2006-2007 J-NCAP (Japanese new car assessment program) full-lap frontal barrier crash tests and offset frontal deformable barrier crash tests data. For more practical standpoint, we conducted thirteen crash tests reconstructing typical real-world accidents such as single vehicle accidents with barriers or poles, car to car accidents and multi rear-end collisions focusing on Japanese typical accident types. Data obtained from EDRs are compared with data obtained from optical speed sensor, instrumented accelerometers and high speed video cameras. The velocities determined from pre-crash data of EDRs and the maximum change in velocity, delta-V, and delta-V time history data obtained from post-crash data of EDRs are analyzed. The results are as follows: - Pre-crash velocities of EDRs were very accurate and reliable. An average difference between the EDR recording values and reference speeds was 4.2% and a root mean square of the differences was 9.2%. Only two cases resulted large differences for the pre-crash velocity. Both of them were cases with braking prior to the collision. However, another test with braking resulted less difference. The braking condition may influence accuracy of pre-crash velocities. - Maximum delta-Vs obtained from the EDRs showed uncertainty of measurement in several cases in comparisons with the reliable delta-V data. The differences in maximum delta-V were more than 10% in five of twenty-five events data and more than 20% in two of twenty-five events data. An average of the all differences was about 4% and root mean square of the differences was about 11%. Especially large deformation at narrow area may influence accuracy of post-crash delta-V. - Multiple rear-end crash tests were reconstructed using EDRs data as case studies. Some EDRs recorded two events and a time gap between two events, so that these reconstruction case studies were very accurate and reliable. - If though only one of three vehicles in multiple rear end crash was equipped EDR, overview and velocities of all cars may be reconstructed using these limited EDR data. In this case study, leading car- EDR data and middle car- EDR data were valuable. However if only following car was equipped EDR, the reconstruction was not accurate
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
Powered Two Wheeler (Motorcycle) crashes are overrepresented in EU, England, and United States casualty statistics for both fatal and serious injuries. While regional geographic differences are evident for motorcycle size, type, and engine displacement, the casualty statistics consistently indicate significantly higher injury rates for all motorcycle riders when compared to car occupants. Accident analysis and reconstruction of these motorcycle crashes is a necessary process to gain further understanding of potential injury mitigation strategies. This paper focuses on the analysis of the rider post impact trajectory in the immediate moments following a crash. The rider and motorcycle, while loosely coupled by seating position leading up to a crash, quickly decouple as the crash forces develop. As a result, the rider moves relative to the motorcycle and relative to the collision partner. This movement, or trajectory, is primarily influenced by the type and configuration of the impact, the type and configuration of the motorcycle and collision partner, and the speeds involved. Understanding the rider's post impact trajectory will assist in the development of injury mitigation strategies. Both the free flight trajectory of the rider and the rider's trajectory as influenced by interaction with the motorcycle and collision partner are examined. Rider trajectories in full scale crash testing and real world motorcycle crashes are both studied and presented. The resulting physical evidence that can be observed by an accident analyst is discussed. The application of projectile motion physics is analyzed and the necessary input parameters, such as initial launch angle, are studied. This study will assist in understanding the post-impact dynamics of a motorcyclist, and will provide useful information to analysts evaluating real world crashes.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.