Abteilung Fahrzeugtechnik
Filtern
Erscheinungsjahr
Dokumenttyp
- Buch (Monographie) (15)
- Wissenschaftlicher Artikel (11)
- Konferenzveröffentlichung (9)
- Arbeitspapier (7)
Schlagworte
- Versuch (42) (entfernen)
Der Nutzen des Schutzhelmes für motorisierte Zweiradfahrer ist unumstritten. Die Grenzwerte für eine zulässige Kopfbeschleunigung bei der Prüfung des Dämpfungsverhaltens gemäß ECE-R 22 sind jedoch weiterhin in der Diskussion. In der vorliegenden Untersuchung wird deshalb die Kopfbelastung eines Dummys beim Pkw-Crash-Versuch mit den Belastungen des behelmten Prüfkopfes bei Fallversuchen gemäß ECE-R 22 verglichen. Bei den durchgeführten Fallversuchen besteht ein enger Zusammenhang zwischen HIC und maximaler Beschleunigung, der durch eine analytische Funktion beschrieben werden kann. Es kann gezeigt werden, dass die bei ECE-R 22 zulässige Kopfbeschleunigung von 300 g einem HIC von etwa 3400 entspricht. Zur Bewertung von Schutzhelmen mit verbesserten Stoßabsorptionseigenschaften erscheint es sinnvoll, wie anhand von Modellrechnungen gezeigt wird, den HIC als Schutzkriterium einzuführen. Bei einer Anprallgeschwindigkeit von 7 m/s kann ein HIC von 1500 als realistische Forderung angesehen werden, sofern bei der ECE-Regelung der sogenannte Zweitschlag entfällt. Bei den Pkw-Versuchen ist kein Zusammenhang zwischen HIC und maximaler Beschleunigung vorhanden. Hier ist der HIC als Verletzungskriterium etabliert, und das ist für den komplexen Verlauf des Signals der Kopfbeschleunigung sinnvoll. Eine Bewertung nach anderen Kopfschutzkriterien würde die Rangfolge der einzelnen Versuche ändern. Bei Helmversuchen auf den Stirnanprallpunkt B werden starke Rotationen des rückprallenden Systems Prüfkopf/Helm beobachtet. In Verbindung damit treten hohe Rotationsbeschleunigungen auf. Diese liegen, wie bei einem Teil der Helmversuche gemessen, zwischen 2,4 und 4,8 krad/s2.
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of synthetic and plastic materials as a material for the interior equipment of buses and coaches because of their ood mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years - also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, the production of smoke, the smoke development and propagation and its toxicity for the people as well as the testing methods and limit values are of interest. For those reasons research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behavior of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and on-board extinguishing equipment were elaborated. At the other hand research is carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. The paper describes which effective and economically reasonable fire safety requirements for interiors of buses would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
The objectives of the FIMCAR (Frontal Impact and Compatibility Assessment Research) project are to answer the remaining open questions identified in earlier projects (such as understanding of the advantages and disadvantages of force based metrics and barrier deformation based metrics, confirmation of specific compatibility issues such as structural interaction, investigation of force matching) and to finalise the frontal impact test procedures required to assess compatibility. Research strategies and priorities were based on earlier research programs and the FIMCAR accident data analysis. The identified real world safety issues were used to develop a list of compatibility characteristics which were then prioritised within the consortium. This list was the basis for evaluating the different test candidates. This analysis resulted in the combination of the Full Width Deformable Barrier test (FWDB) with compatibility metrics and the existing Offset Deformable Barrier (ODB) as described in UN-ECE Regulation 94 with additional cabin integrity requirement as being proposed as the FIMCAR assessment approach. The proposed frontal impact assessment approach addresses many of the issues identified by the FIMCAR consortium but not all frontal impact and compatibility issues could be addressed.
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for over 10 years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and the final report to the steering committee on frontal impact [Faerber 2007] and the FP5 VC-COMPAT[Edwards 2007] project activities, two test approaches were identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in current research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis will be performed. In the FIMCAR Deliverable D 3.1 [Adolph 2013] the development and assessment of criteria and associated performance limits for the full width test procedure were reported. In this Deliverable D3.2 analyses of the test data (full width tests, car-to-car tests and component tests), further development and validation of the full width assessment protocol and development of the load cell and load cell wall specification are reported. The FIMCAR full-width assessment procedure consists of a 50 km/h test against the Full Width Deformable Barrier (FWDB). The Load Cell Wall behind the deformable element assesses whether or not important Energy Absorbing Structures are within the Common Interaction Zone as defined based on the US part 581 zone. The metric evaluates the row forces and requires that the forces directly above and below the centre line of the Common Interaction Zone exceed a minimum threshold. Analysis of the load spreading showed that metrics that rely on sum forces of rows and columns are within acceptable tolerances. Furthermore it was concluded that the Repeatability and Reproducibility of the FWDB test is acceptable. The FWDB test was shown to be capable to detect lower load paths that are beneficial in car-to-car impacts.
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for over 10 years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in current research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The objectives of the work reported in this deliverable were to review existing full-width test procedures and their discussed compatibility metrics, to report recent activities and findings with respect to full-width assessment procedures and to assess test procedures and metrics. Starting with a review of previous work, candidate metrics and associated performance limits to assess a vehicle- structural interaction potential, in particular its structural alignment, have been developed for both the Full Width Deformable Barrier (FWDB) and Full Width Rigid Barrier (FWRB) tests. Initial work was performed to develop a concept to assess a vehicle- frontal force matching. However, based on the accident analyses performed within FIMCAR frontal force matching was not evaluated as a first priority and thus in line with FIMCAR strategy the focus was put on the development of metrics for the assessment of structural interaction which was evaluated as a first priority.
Cost benefit analysis
(2014)
Although the number of road accident casualties in Europe is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities [EC 2012]. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car- safety performance in frontal impacts is to improve its compatibility for car-to-car impacts and for collisions against objects and HGVs. Compatibility consists of improving both a car- self and partner protection in a manner such that there is good interaction with the collision partner and the impact energy is absorbed in the car- frontal structures in a controlled way which results in a reduction of injuries. Over the last ten years much research has been performed which has found that there are four main factors related to a car- compatibility [Edwards 2003, Edwards 2007]. These are structural interaction potential, frontal force matching, compartment strength and the compartment deceleration pulse and related restraint system performance. The objective of the FIMCAR FP7 EC-project was to develop an assessment approach suitable for regulatory application to control a car- frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation.
The objective of this deliverable is to describe the expected influence of the candidate test procedures developed in FIMCAR for frontal impact on other impact types. The other impact types of primary interest are front-to-side impacts, collisions with road restraint systems (e.g. guardrails), and heavy goods vehicle impacts. These collision types were chosen as they involve structures that can be adapted to improve safety. Collisions with vulnerable road users (VRU) were not explicitly investigated in FIMCAR. It is expected that the vehicle structures of interest in FIMCAR can be designed into a VRU friendly shell. Information used for this deliverable comes from simulations and car-to-car crash tests conducted in FIMCAR or review of previous research. Three test configurations (full width, offset, and moving deformable barriers) were the input to the FIMCAR selection process. There are three different types of offset tests and two different full width tests. During the project test procedures could be divided into three groups that provide different influences or outcomes on vehicle designs: 1. The ODB barrier provides a method to assess part of the vehicles energy absorption capabilities and compartment test in one test. 2. The FWRB and FWDB have similar capabilities to control structural alignment, further assess energy absorption capabilities, and promote the improvements in the occupant restraint system for high deceleration impacts. 3. The PDB and MPDB can be used to promote better load spreading in the vehicle structures, in addition to assessing energy absorption and occupant compartment strength in an offset configuration. The consortium selected the ODB and FWDB as the two best candidates for short term application in international rulemaking. The review of how all candidates would affect vehicle performance in other impacts (beside front-to-front vehicle or frontal impacts with fixed obstacles) however is reported in this deliverable to support the benefit analysis reported in FIMCAR. The grouping presented above is used to discuss all five test candidates using similarities between certain tests and thereby simplify the discussion.
Accident analysis
(2014)
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the EC funded FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in today- research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The specific objectives of the work reported in this deliverable were: - Determine if previously identified compatibility issues are still relevant in current vehicle fleet: Structural interaction, Frontal force matching, Compartment strength in particular for light cars. - Determine nature of injuries and injury mechanisms: Body regions injured o Injury mechanism: Contact with intrusion, Contact, Deceleration / restraint induced. The main data sources for this report were the CCIS and Stats 19 databases from Great Britain and the GIDAS database from Germany. The different sampling and reporting schemes for the detailed databases (CCIS & GIDAS) sometimes do not allow for direct comparisons of the results. However the databases are complementary " CCIS captures more severe collisions highlighting structure and injury issues while GIDAS provides detailed data for a broader range of crash severities. The following results represent the critical points for further development of test procedures in FIMCAR.
The off-set assessment procedure potentially contributes to the FIMCAR objectives to maintain the compartment strength and to assess load spreading in frontal collisions. Furthermore it provides the opportunity to assess the restraint system performance with different pulses if combined with a full-width assessment procedure in the frontal assessment approach. Originally it was expected that the PDB assessment procedure would be selected for the FIMCAR assessment approach. However, it was not possible to deliver a compatibility metric in time so that the current off-set procedure (ODB as used in UNECE R94) with some minor modifications was proposed for the FIMCAR Assessment Approach. Nevertheless the potential to assess load spreading, which appears not to be possible with any other assessed frontal impact assessment procedure was considered to be still high. Therefore the development work for the PDB assessment procedure did not stop with the decision not to select the PDB procedure. As a result of the decisions to use the current ODB and to further develop the PDB procedure, both are covered within this deliverable. The deliverable describes the off-set test procedure that will be recommended by FIMCAR consortium, this corresponds to the ODB test as it is specified in UN-ECE Regulation 94 (R94), i.e. EEVC deformable element with 40% overlap at a test speed of 56 km/h. In addition to the current R94 requirements, FIMCAR will recommend to introduce some structural requirements which will guarantee sufficiently strong occupant compartments by enforcing the stability of the forward occupant cell. With respect to the PDB assessment procedure a new metric, Digital Derivative in Y direction - DDY, was developed, described, analysed, and compared with other metrics. The DDY metric analyses the deformation gradients laterally across the PDB face. The more even the deformation, the lower the DDY values and the better the metric- result. In order analyse the different metrics, analysis of the existing PDB test results and the results of the performed simulation studies was performed. In addition, an assessment of artificial deformation profiles with the metrics took place. This analysis shows that there are still issues with the DDY metric but it appears that it is possible to solve them with future optimisations. For example the current metric assesses only the area within 60% of the half vehicle width. For vehicles that have the longitudinals further outboard, the metric is not effective. In addition to the metric development, practical issues of the PDB tests such as the definition of a scan procedure for the analysis of the deformation pattern including the validation of the scanning procedure by the analysis of 3 different scans at different locations of the same barrier were addressed. Furthermore the repeatability and reproducibility of the PDB was analysed. The barrier deformation readings seem to be sensitive with respect to the impact accuracy. In total, the deliverable is meant to define the FIMCAR off-set assessment procedure and to be a starting point for further development of the PDB assessment procedure.
Aufgrund des demografischen Wandels werden in der Zukunft immer mehr ältere Menschen ein Kraftfahrzeug führen. Das vorliegende Projekt soll Erkenntnisse dazu liefern, wie unter Berücksichtigung der Verkehrssicherheit die Mobilität der älteren Fahrer so lange wie möglich erhalten werden kann. Unfallanalysen zeigen, dass ältere Kraftfahrer typische Fahrfehler bzw. Unfälle begehen. Unklar ist derzeit die genaue Ursache hierfür, vor allem vor dem Hintergrund der langjährigen Erfahrung älterer Kraftfahrer, welche eher eine äußerst geringe Unfallrate vermuten ließe. Ziel der vorliegenden Untersuchung war es, tiefere Erkenntnisse äber die Ursache von Fahrfehlern älterer Kraftfahrer zu gewinnen, um daraus Anforderungen an die technische Weiterentwicklung von Fahrerassistenzsystemen ableiten zu können. Diese Fahrerassistenzsysteme sollen speziell älteren Autofahrern Hilfestellung zum sicheren Führen von Kraftfahrzeugen bieten. In dem folgenden Laborexperiment wurde ein Doppeltätigkeits-Paradigma verwendet, indem eine Spurhalteaufgabe mit einer peripheren Lichtreizaufgabe kombiniert wurde. Die peripheren Lichtreize wurden den Probanden bilateral in zwei verschiedenen Abständen vom zentralen Punkt des Sehens (20 Grad und 60 Grad) präsentiert. Die Aufgaben wurden von älteren (65+) und jüngeren Kraftfahrern (22-45) zuerst einzeln, dann in Kombination durchgeführt. Um Aufschluss über mögliche Ursachen von Leistungsbeeinträchtigungen erhalten zu können, wurde neben der Erfassung von Verhaltensdaten (Spurabweichungen, Reaktionszeit, Anzahl der Auslassungen) ein Elektroenzephalogramm abgeleitet, welches Einblicke in die zugrunde liegenden neuronalen Verarbeitungsmechanismen ermöglicht. Wie erwartet, zeigten Ältere in der Spurhalteaufgabe schlechtere Leistungen als Jüngere, besonders bei gleichzeitiger Durchführung der Lichtreizaufgabe (Doppel-Aufgabe). In der Lichtreizaufgabe unterschieden sich die Leistungen der Altersgruppen nur bei Lichtreizen, die im 60 Grad Sehwinkel auftraten. Die Älteren reagierten hier langsamer und zeigten mehr Auslassungen als die Jüngeren. Überraschenderweise zeigten alle Versuchspersonen weniger Auslassungen in der Doppel-Aufgabe. Mittels Elektroenzephalogramm wurde anhand der ereigniskorrelierten Potenziale (EKP) deutlich, dass die Defizite Älterer nicht in einer Einschränkung der frühen Verarbeitung peripherer Reize (P1) liegen, da die P1 Amplitude bei Älteren sogar höher war als bei Jüngeren. Die N2 Amplitude, welche Hinweise auf die Verschiebung der Aufmerksamkeit gibt, war bei Jüngeren hingegen bei weiter peripher liegenden Reizen (60 Grad Sehwinkel) erhöht, was einen fronto-zentral fokussierten Kontrollprozess widerspiegelt. Die Orientierung auf den peripheren Reiz (P3a) war bei Älteren geringer ausgeprägt sowie auch die Zuordnung von Verarbeitungsressourcen (P3b) vor allem bei peripheren Lichtreizen. Es liegen zudem Hinweise darauf vor, dass Ältere verlängerte Reaktionszeiten aufgrund einer verzögerten Reaktionsaktivierung aufweisen. Mit dem vorliegenden Experiment konnte also gezeigt werden, dass die schlechteren Leistungen der älteren Versuchspersonen nicht auf periphere Sehleistungsmängel zurückzuführen sind, sondern einem späteren kognitiven Verarbeitungsprozess zuzuschreiben sind. Die Ergebnisse werden vor dem Hintergrund der Literatur und der Erfordernisse technischer Unterstützungen älterer Kraftfahrer diskutiert.
Mit der EU-Verordnung Nummer 661/2009 zur Typgenehmigung und allgemeinen Sicherheit von Kraftfahrzeugen wird von der EU für schwere Nutzfahrzeuge der Einbau von Spurverlassenswarnsystemen und automatischen Notbremssystemen vorgeschrieben. Mit dem obligatorischen Einbau der Systeme wird eine Reduktion der Abkommens- und Auffahrunfälle von Nutzfahrzeugen aus den Klassen M2, M3, N2 und N3, die auf Grund der hohen Masse der Fahrzeuge folgenschwer sind, erwartet. Als Einführungsdaten werden der 1. November 2013 für neue Fahrzeugtypen und der 1. November 2015 für neue Fahrzeuge genannt. Leistungsanforderungen beziehungsweise technische Spezifikationen, denen die Systeme genügen müssen, liegen jedoch noch nicht vor. Diese werden derzeit von einer Expertengruppe auf UN-ECE-Ebene entwickelt. Dabei wird versucht, technologieneutrale Beschreibungen für die Ausgestaltung der Systeme zu erstellen, die gleichzeitig sowohl den gewünschten Nutzen für die Verkehrssicherheit garantieren, sich aber auch an der derzeit vorhandenen und realisierbaren Technologie orientieren. Darüber hinaus müssen die Systemkosten in einem vernünftigen Verhältnis zum Sicherheitsnutzen stehen. Ziel ist es, im Laufe des Jahres 2011 Vorschläge für die Legislative vorzulegen. Es wird über den Stand der Arbeiten, offene Fragestellungen, Herausforderungen bei der Ausgestaltung der technischen Anforderungen sowie sich abzeichnende Ergebnisse berichtet. Dabei sind die Arbeiten in Bezug auf Lane Departure Warning Systems (LDWS) bereits weiter fortgeschritten als zu Advanced Emergency Braking Systems (AEBS).
Falltests zur Untersuchung der Belastungen von Dummys beim Aufprall auf den Boden, Teil 1 und 2
(2010)
Beim Zusammenprall eines Motorrads mit einem Pkw unterscheidet man in der Unfallforschung sowohl den Erstanprall des Motorradfahrers an den Pkw als auch den Sekundäraufprall des Motorradfahrers auf dem Boden. So genannte Full-Scale-Crashtests mit Dummys haben beim Erstanprall gezeigt, dass Motorradfahrer durch Airbags potenziell geschützt werden können. Bei den entsprechenden Unfallsimulationen wurde jedoch im weiteren Bewegungsablauf beim nachfolgenden Sekundäraufprall auf dem Boden festgestellt, dass relativ hohe Belastungen auf den Dummy einwirken. Es stellt sich hierbei jedoch die Frage, ob die üblicherweise für Lasteinwirkungen im Falle eines Erstanpralls entwickelten und validierten Dummys die bei einem Sekundäraufprall auf einen Motorradfahrer einwirkenden Belastungen hinreichend genau wiedergeben können. Dazu wurden die Belastungen eines Dummys beim Aufprall auf den Boden untersucht, um das Verletzungsrisiko eines menschlichen Motorradfahrers einschätzen zu können. Im Dekra-Crash-Test-Center wurden vier verschiedene Aufprallsituationen mit einem Hybrid III Dummy durchgeführt, wobei diese Tests an eine andere Testreihe angelehnt sind, die bereits am US-amerikanischen Institut "Dynamic Research International" (DRI) durchgeführt worden waren. Nach der Erläuterung des Testaufbaus und seiner Durchführung wird detailliert auf die gemessenen Verzögerungsbelastungen des Dummys eingegangen. Hierbei geben zum einen Tabellen eine Übersicht über charakteristische Messwerte zur Quantifizierung der maximalen Belastung des Dummys, zum anderen veranschaulichen Bilder die zugehörigen zeitlichen Verzögerungsverläufe in Becken, Brust und Kopf des Dummys. Der Artikel schließt mit einer Interpretation der Versuchsergebnisse und gibt einen Ausblick auf den weiteren Untersuchungsbedarf.
Run-Flat-Reifen (Reifen mit Notlaufeigenschaften) stellen eine sicherheitsrelevante Komponente am Fahrzeug dar. Im Gegensatz zu Standardreifen bieten sie die Eigenschaft, auch im drucklosen Zustand noch eine gewisse Wegstrecke mit dem Fahrzeug zurücklegen zu können. In der vorliegenden Untersuchung wurden verschiedene Run-Flat-Reifen auf ihre Leistungsfähigkeit hin untersucht. Zum einen wurde die Dauerhaltbarkeit der Reifen getestet. Die zugehörigen Messungen wurden im Innentrommelprüfstand der BASt durchgeführt. Zum anderen wurden die fahrdynamischen Eigenschaften eines Fahrzeugs, das mit Run-Flat-Reifen ausgerüstet war, auf der Versuchsfläche der BASt untersucht. Im Rahmen einer Literaturrecherche wurde weiterhin das im Zusammenhang mit Run-Flat-Reifen stehende Thema Reifendruckkontrolle behandelt. Die Versuche zur Dauerhaltbarkeit der Reifen haben gezeigt, dass große Unterschiede bezüglich der erreichbaren Notlaufstrecke der Run-Flat-Reifen bestehen. Unter den Prüfbedingungen der BASt, die auch Phasen mit Verzögerungen, Beschleunigungen und Schräglauf enthielten, wurden teilweise die von den Herstellern vorgegebenen Strecken nicht erreicht, teilweise jedoch auch weit überschritten. In Bezug auf den Einfluss von Run-Flat-Reifen auf die fahrdynamischen Eigenschaften des Fahrzeugs ist festzustellen, dass die Run-Flat-Reifen im druckbehafteten Zustand Standardreifen in nichts nachstehen. Im drucklosen Zustand bieten sie noch gutes Fahrverhalten, wenn mit Standardreifen an eine Weiterfahrt nicht mehr zu denken ist. In Bezug auf die Fahrdynamik lassen sich bei den Run-Flat-Reifen untereinander kaum Unterschiede ausmachen. Das gilt auch für den Vergleich von Reifen mit verstärkter Seitenwand und Reifen mit innerem Stützring. Insgesamt stellen Run-Flat-Reifen einen deutlichen Sicherheitsgewinn gegenüber Standardreifen für den Fall eines Luftverlustes eines Reifens dar. Es hat sich herausgestellt, dass eine Druckkontrolle bei der Verwendung von Run-Flat-Reifen dringend zu empfehlen ist, da sonst ein Druckverlust eventuell nicht bemerkt wird. Dafür kommen sowohl direkte als auch indirekte Reifendruckkontrollsysteme in Frage. Die Ergebnisse zeigen weiterhin, dass eine Prüfprozedur für neue Typen von Run-Flat-Reifen erforderlich ist, um die erforderlichen Notlaufeigenschaften zu garantieren. Mit Hilfe von Seitenwandbeschriftungen am Reifen sollte der Nutzer auf Notlaufstrecke und -geschwindigkeit hingewiesen werden.
Studien zeigen, dass vom Fahren mit Licht am Tag ein Verkehrssicherheitsgewinn erwartet wird. Daher wird in Deutschland seit Oktober 2005 empfohlen, dass alle mehrspurigen Kraftfahrzeuge am Tag mit eingeschaltetem Abblendlicht oder speziellen Tagfahrleuchten (nach ECE-R87) fahren sollen. Tagfahrleuchten für mehrspurige Kraftfahrzeuge sind speziell auf die Erkennbarkeit des Kraftfahrzeuges ausgelegt und haben eine andere Abstrahlcharakteristik als Abblendlicht. Bei einer vermehrten Verbreitung von Tagfahrleuchten bei mehrspurigen Kraftfahrzeugen ist nicht ausgeschlossen, dass Motorräder im Vergleich zur heutigen Situation schlechter erkennbar sein werden, da Motorräder derzeit nicht mit Tagfahrleuchten ausgerüstet werden dürfen. Aus diesem Grund wurde in der vorliegenden Studie untersucht, inwieweit sich die Erkennbarkeit von Motorrädern gegenüber der derzeitigen Situation steigern lässt. Gleichzeitig sollte geklärt werden, ob Motorräder mit dem heutigen Signalbild am Tag (Abblendlicht) zukünftig schlechter erkennbar sein könnten. Folgende unterschiedliche Leuchtenkonfigurationen, die die Motorräder mit einem gesonderten oder angepassten Signalbild besser sichtbar und erkennbar machen sollen, wurden dafür an zwei verschiedenen Motorrädern montiert: Abblendlicht, Abblendlicht mit dauerhaft leuchtenden vorderen Fahrtrichtungsanzeigern, Tagfahrleuchten in Weiß, selective Yellow und Amber sowie weiße Tagfahrleuchten als Paar beziehungsweise mit größerer Lichtstärke. Im statischen Versuch wurden diese dann durch Probanden in verschiedenen realitätsnahen Verkehrssituationen vergleichend bewertet. Abschließend wurden Vorschläge für ein optimiertes vorderes Signalbild von Motorrädern und damit verbundene notwendige Vorschriftenänderungen erarbeitet. Die wichtigsten Ergebnisse für die Verbesserung des vorderen Signalbildes am Motorrad sind: • Eine Tagfahrleuchte nach ECE-R87 ist besser erkennbar als Abblendlicht. • Zwei Tagfahrleuchten sind besser erkennbar als eine Tagfahrleuchte. • Lichtstärkere Tagfahrleuchten sind auf größere Entfernung besser erkennbar als lichtschwächere Tagfahrleuchten, während Erkennbarkeitsunterschiede durch verschiedene Farben beziehungsweise Farbbereiche mit zunehmender Beobachtungsentfernung abnehmen. • Mehrspurige Fahrzeuge und ihre Beleuchtung hatten keinen Einfluss auf die Erkennbarkeitsbewertung der Motorräder. Als Konsequenz der Untersuchungsergebnisse zur Erkennbarkeit von Motorrädern sollte der Anbau von einer oder zwei Tagfahrleuchten nach ECER87 an Motorrädern erlaubt werden, um tagsüber mit eingeschalteten Tagfahrleuchten anstelle des Abblendlichts fahren zu können. Dadurch ist eine Verbesserung der Erkennbarkeit von Motorrädern am Tag möglich und zusätzlich kann der Energieverbrauch durch die Beleuchtung gemindert werden.