91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (164) (entfernen)
Schlagworte
- Conference (100)
- Konferenz (97)
- Germany (53)
- Deutschland (52)
- Accident (48)
- Unfall (48)
- Safety (44)
- Sicherheit (44)
- Fahrzeug (38)
- Vehicle (36)
Institut
Rollover scenarios in Europe
(2005)
Rollover accidents seem to be a rising problem in Europe and therefore the systematic of this accident scenario should be investigated. Based on statistical investigations on major European accident databases for different countries a series of 73 real world rollover accidents was analysed. These cases were reconstructed using PC-Crash and preliminary categorised using a modified USbased rollover classification. In a first step, the rollover events were reconstructed from the point of conflict to the vehicle- rest position. The vehicles kinematics as well as its linear and rotational velocities were derived. In a second step typical velocity characteristics as well as kinematics were identified and the events categorised according to these criteria. Based on these results four main categories were defined, covering all reconstructed accidents. This categorisation was based on mechanical parameters (rotatory and translator kinematical data of the vehicle). Significant differences can be seen for different scenarios for the "first phase of rollover".
The second ESAR Conference took place at the Medical University Hannover. This year conference presents the current state of affairs of relevant research activities in the field of in-depth investigations. The first conference on ESAR (Expert Symposium on Accident Research) was established in 2004. It is planned to hold ESAR every two years. Hannover seems to be the right place for this conference concerning the fact that the first in-depth research team was found here in the year 1973 and comprehensive studies on accident analysis were spread out from here around the world continuously. This year conference topped all expectations in terms of the numbers of participants, in the variety of papers and the interdisciplinary of presenters from medical, psychological and engineering background. More than 100 delegates from all over the world, that means 13 different countries and from 4 different continents, came to Hannover, presented their results of accident investigation and discussed countermeasures for accident prevention and injury reduction. ESAR should be a platform for exchange of knowledge to find an optimized way for increase of traffic and vehicle safety by in-depth investigation and methodology. ESAR as international conference should be a platform for consideration of all nations round the world. This seems to be very important for the current situation, having high safety in the high industrial countries of Europe, US and Australia, but low safety and high injury risk in Asia and Africa.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 13. Oktober 2006 in Baden-Baden das 6. Symposium "Sicher fahren in Europa". Die Fachvorträge befassten sich mit den Themenbereichen: Ansätze zu mehr Verkehrssicherheit, - Verbesserung der Fahrzeugsicherheit, - Besondere Zielgruppen. Die CD-ROM dokumentiert die Grußworte, die Referate und die Podiumsdiskussion.
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
There is a need for detecting characteristics of pedestrian movement before car-pedestrian collisions to trigger a fully reversible pedestrian protection system. For this purpose, a pedestrian sensor system has been developed. In order to evaluate the effectiveness of the sensor system, the in-depth knowledge of car-pedestrian impact scenarios is needed. This study aims at the evaluation of the sensor system. The accident data are selected from the STRADA database. The accident scenarios available in this database were evaluated and the knowledge of the most common scenarios was developed in terms of the pedestrian trajectory, the pedestrian speed, the car trajectory, the car velocity, etc. A mathematical model was then established to evaluate the sensor system with different detective angles. It was found that in order to detect all the pedestrians in the most common scenarios on time the sensor detective angle must be kept larger than 60 degrees.
Institute for Traffic Accident Research and Data Analysis <Tokyo>rnAbstract: Analyses were conducted to clarify the features of rear-end collisions, using an integrated accident database developed by the Institute for Traffic Accident Research and Data Analysis (ITARDA). Focusing on neck injuries in rear-end collisions, analyses were made of the relation to struck-vehicle properties. Regarding the relation to the initial year of registration, the results did not show that newer vehicles tended to have a lower no-neck-injury rate, which was defined in this study as an index. On the contrary, in some passenger car classes, it was observed that the no-neck-injury rate was higher in newer vehicles. The effect of an active head restraint system, which is one type of anti-whiplash device, was analyzed by using not only the no-neck-injury rate but also a regression analysis. The results showed that the effect of an active head restraint system on suppressing the incidence of neck injuries was statistically significant.rn
In recent years the boundaries between active and passive safety blurred more and more. Passive safety in the traditional term includes all safety aspects to prevent occupants to be injured or at least injury severity should be reduced. Passive Safety starts with the collision (first vehicle contact) and ends with rescue (open vehicle doors). Within this phase the occupant has to be protected by the passenger compartment whereby no intrusion should occur. Active safety on the other side was developed to interact prior to the collision whereby the goal is to prevent accidents. The extensive interaction between active and passive safety led to the terminologies "Primary" and "Secondary" safety whereas the expression Integrated Safety Concept was generated. Within this study the most well documented single vehicle accidents with cars not equipped with ESP were identified from the PENDANT database and reconstructed. Additional cases were found in the database ZEDATU of TU Graz. In comparison each case was simulated with the assumption that the cars were equipped with ESP. The differences regarding accident avoidance or crash severity as well as reduction of injury risk were analysed.
The price of a new car increased almost every year for a long period. In recent years however, the budget available to most people for purchasing a car either did not grow or became even smaller. Therefore it was in the interest of some OEMs to offer economical car models in the so-called "8,000- Euro class". Here an important question arose regarding the safety of these vehicles. There is no question that the very high safety level of cars reached in Europe during the last decades should not be sacrificed as a consequence of smaller budgets. Customers with sense of responsibility have the right to be properly informed about the balance between safety and price so that they can make a deliberate decision when buying either a new or a used car. Against this background, the German magazine "AutoBILD" commissioned DEKRA to conduct fullscale frontal crash tests with a view to publishing the results. These tests have been carried out in accordance with the corresponding Euro NCAP crash test requirements and performance criteria. The tested vehicles were two new Logans produced by the manufacturer Dacia, two used cars of the type VW Golf IV (registration date 2000) and one new VW Fox. This paper describes the safety features of the vehicles and the results of the five crash tests to demonstrate state-of-the-art safety levels and what levels may be expected from vehicles in the "8,000- Euro class". Looking at real-world crashes it is of interest to think about future trends in a more detailed manner. Therefore it will be more and more necessary to supplement the federal statistics with more detailed in-depth information about the consequences of accidents and the safety performance of crashed vehicles.
During the last 5 years, the number of cars fitted with side airbags has dramatically increased. They are now standard equipment, even on many smaller cars or less luxurious vehicles. While some side airbags offer thoracic protection alone, there are those that combine thoracic and head protection (of which most deploy from the seat). Other systems employ separate airbags for head and thorax protection, which are designed to be effective noticeably in a crash against a pole. This paper proposes an evaluation of the effectiveness of side airbags in preventing thoracic injuries to passenger car occupants involved in side crashes. First, the target population (who can take benefit of side airbag deployment and in what circumstances) is defined. Side airbags can be especially effective in cases of impacts on the door with intrusion at a certain impact speed. Then, an example case of a side impact with side airbag deployment is given were side airbag deployment is thought to have had a positive effect on injury outcome. A further case is presented where the impact configuration is likely to have reduced the effect of side airbag deployment on injury outcome. Finally, the estimation of side airbag effectiveness (in terms of additional occupant protection brought exclusively by the airbag) is proposed by comparing injury risk sustained by occupants in (more or less) similar cars (fitted or non fitted with airbags) because, during these years, car structure, and side airbag conception have considerably evolved. In-depth accident data from France, the UK and Germany has been collected. Out of 2,035 side impact accident cases available in the databases, we selected 435 occupants of passenger cars (built from 1998 onwards) involved in an injury accident between year 1998 and year 2004 for EES (Energy Equivalent Speed) values between 20km/h and 50km/h. The occupants, belted or not, were sat on the struck side, whatever the obstacle and type of accidents (intersection, loss of control, etc.). For multiple impact crashes, the side impact is assumed to be the more severe one. Passenger cars were fitted with (96) or without (339) side airbags. Most of the potential risk explanatory variables were correctly and reliably reported in the databases (velocity " impact zone " impact angle " occupant characteristics, etc.). The analysis compared injury risks for different levels of EES and different types of side airbags. A logistic regression model was also computed with injury variables (such as thoracic AIS 2+ or AIS 3+) as the dependant variable and other variables (including airbag type and EES) as explanatory injury risk factors. Results revealed statistically non-significant reductions in thoracic AIS 2+ and AIS 3+ injury risk in side airbag equipped cars in the impact violence range selected (odds ratio between 0.84 and 0.98 depending on types of airbags). The results are discussed. The non-significance is assumed to be due to a low number of cases. Statistical analysis for head injuries was not possible due to the low number of accident cases with passenger cars fitted with head airbags in the databases. Moreover, the discrepancies between the data coming from different countries (especially calculation of EES) might have introduced instability in the analysis.
This paper uses the national accident statistics of Great Britain to evaluate the effectiveness of Electronic Stability Control Systems (ESC) to reduce crash involvement rates. The crash experience of 8,951 cars is analysed and compared to a closely matching set of non-ESC cars using case-control methods. This is one of the largest ESC samples analysed to date. Overall the cars with ESC are involved in 3% fewer crashes although the effectiveness is substantially higher under conditions of adverse road friction. ESC equipped cars are involved in 15% fewer fatal crashes although this reduction represents the combined effect of ESC and passive safety improvements.
Description of road traffic related knee injuries in published investigations is very heterogeneous. The purpose of this study was to estimate the risk of knee injuries in real world car impacts in Germany focusing vulnerable road users (pedestrians, bicyclists and motorcyclists) and restrained car drivers. The accident research unit analyses technical and medical data collected shortly after the accident at scene. Two different periods (years 1985-1993 and 1995-2003) were compared focusing on knee injuries (Abbreviated Injury Scale (AISKnee) 2/3). In order to determine the influences type of collision, direction and speed as well as the injury pattern and different injury scores (AIS, MAIS, ISS) were examined. 1.794 pedestrians, 742 motorcyclists, 2.728 bicyclists and 1.116 car drivers were extracted. 2% had serious ligamentous or bony injuries in relation to all injured. The risk of injury is higher for twowheelers than for pedestrians, but knee injury severity is higher for the latter group. Overall the current knee injury risk is low and significant reduced comparing both time periods (27%, p<0,0001). Severe injuries (AISKnee 2/3) were below 1%). Improved aerodynamic design of car fronts reduced the risk for severe knee injuries significantly (p=0,0015). Highest risk of injury is for motorcycle followed by pedestrians, respectively. Knee protectors could prevent injuries by reducing local forces. The classically described dashboard injury was rarely identified. The overall injury risk for knee injuries in road traffic is lower than estimated and reduced comparing both periods. The aerodynamic shape of current cars compared to older types reduced the incidence and severity of knee injuries. Further modification and optimization of the interior and exterior design could be a proper measurement. Classic described injury mechanisms were rarely identified. It seems that the AIS is still underestimating extremity injuries and their long term results.
Motorcycle safety research
(2007)
Honda- global motorcycle sales exceeded the 10 million units mark since 2004, and further expansion is expected. As a responsibility for a company to provide mobility, Honda is focusing on motorcycle safety as top priority and has been working on various activities for both aspects of hardware and software. Here, we present Honda- activity for the safety technology of motorcycles. At present, Honda is promoting motorcycle safety in the four themes of prevention and collision safety such as safety education, recognition assistance, accident prevention and injury reduction. First, in the area of the safety education, the "Honda Safety Driving Promotion Center" was established in 1970, and motorcycle riders and vehicle driver trainings have been organized, and the traffic training centers are used as an actual practice field not only in Japan but also in many other regions in the world. Through our training activities, the new area of safety training with hardware assistance was developed and Honda- unique technology was accumulated such as the riding simulator which can provide experience of potentially dangerous situations without risk. Especially, the "riding trainer", the popular version of the riding simulator, was introduced at several motor shows in various countries and launched in September 2005. It was distributed first in Europe and is expected to expand globally aiming at 3000 units worldwide.. And in Europe, the newest version, which includes the suburban roads program, jointly developed with ADAC, will be released in near future. In the area of recognition assistance, "vehicle to vehicle communication technology" is under development using the advantage of being a manufacturer of both motorcycles and cars. This technology is under research as Honda "ASV-3" in Japan, and as part of C2C activity in Europe. As for the accident prevention, advanced brake systems for motorcycles to assist more effective brake operation have been expanded, Honda signed the European Road Safety Charter in April 2004 with the advanced brake systems commitment and furthermore, they are expanding according to vehicle characteristics and region. Then all models above 250 cc will have a version of the system by 2010. And as the last theme, "motorcycle airbag system" is introduced which is equipped on a mass production motorcycle for the first time in the world. It has been researched and developed for a long time as an injury reduction technology for collision accidents. Honda automobile technology was used for the research and development of the motorcycle airbag, and many specific issues such as the analysis of the collision conditions particular to motorcycles have been solved to realize today- success. It might be known that ADAC in-house crash test held in August this year confirmed the high effectiveness of the airbag system and showed a positive result. This motorcycle airbag system is equipped to the Honda Gold Wing and launched in North America in August, 2006. Also in Europe, it will be sold by the end of this year. Each theme of Honda motorcycle safety technology can be seen at the Honda booth.
Die EU hat für die Verkehrssicherheit in Europa ein anspruchsvolles Ziel vorgegeben: Bis 2010 soll die Anzahl der im Straßenverkehr Getöteten gegenüber 2000 halbiert werden. Für Deutschland kann eine erfolgreiche Zwischenbilanz gezogen werden: In den letzten 5 Jahren nahm trotz Vergrößerung des Kraftfahrzeugbestandes um 6% die Anzahl der Verkehrstoten um 29% ab, in den vergangenen 10 Jahren ist ein Rückgang um 43% zu verzeichnen. Diese im internationalen Vergleich überdurchschnittlichen Erfolge sind nicht zuletzt auch auf Fortschritte in der Fahrzeugtechnik zurückzuführen, wobei die zunehmende Verbreitung von Systemen der Aktiven Sicherheit wie ABS, BAS, ESP einen entscheidenden Anteil hat. Nach der deutlichen Reduzierung von Fahrunfällen durch ESP-® stehen nun die Auffahrunfälle im Fokus der Sicherheitsentwicklung von Mercedes-Benz. Das Paket aus verbessertem rückwärtigen Signalbild (Adaptives Bremslicht) und Brems-Assistent (BAS) wurde kürzlich durch radarbasierte Bremsassistenz ergänzt (BAS PLUS und PRE-SAFE-®-Bremse). Der Beitrag geht auf Funktion und Wirksamkeit der einzelnen Systeme ein und gibt einen Ausblick in die nähere Zukunft.
The objective of this study was to identify aspects of the individual experience and behaviour of drivers in intersection accidents. A total of 40 accident drivers sketched their ideas and expectations relating to intersection assistance using the method of Structure Formation Technique. Using this method prepared content cards and relation cards for a subject matter are formed together in a structure through the application of an explicit set of rules. The structures generated in this process were compared with the structures of 20 control persons who have not recently experienced an accident at intersections. The basis for this comparison was a case-control design with matched samples regarding the variables age, sex, education, occupation, driving experience and annual mileage. The results of the accident reports indicate that additional assistance is instrumental in the perception of other road users. Generally the interviewed drivers were open-minded towards the use of intersection assistance systems. Drivers who have recently experienced an accident at intersections significantly more often approved of warning assistance in their vehicle than drivers who have not recently experienced an accident. Further accident experienced drivers favoured warning and information via audio warning more frequently. The ideas of the drivers were strongly shaped by the experiences with already available advanced driver assistance systems. Hence acoustic and visual warnings were generally preferred to tactile warnings. The findings also indicate a relationship between the variable age and the acceptance of automatic vehicle intervention, and the suggestion of a head up display as a configuration of a visual warning system.
Since 2005 the German In-Depth Accident Study (GIDAS) also records aspects of active vehicle safety. This is done because vehicles are fitted with an increasing number of active safety devices which have undoubtedly an influence on the number, severity and course of accidents. Accident researchers expect that collecting active safety data will facilitate to assess and quantify the impact of these and future devices. It is the aim of this paper to outline benefits and limitations associated with the recording of active safety aspects within indepth studies. An overview about possible areas where active safety data can be useful will be given. For that purpose single safety or comfort systems will be selected to estimate the effects of an accident database which includes variables associated with these systems. Questions with regard to the limitations of collecting active safety data will be addressed. Possible items are for example the usability of the data recorded, the real accident cause, the small number of relevant accidents, the time span needed to gather a sufficient dataset, the small share of vehicles equipped with a certain system or different functionalities of systems that are supposed to fall in the same category. As a result user needs for a reasonable data collection of active safety elements will be elaborated.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
In September 2004 the first international symposium called ESAR (Expert Symposium on Accident Research) was carried out at the University of Hannover (Germany). The idea for such international conference was to bring together experts from the fields of accident investigation teams worldwide to present their results for a common audience of people from government, industry and other universities. The first conference was a really sufficient one and followed by the second symposium also at the Hannover Medical School two years later in 2006. This two year rhythm was now continued with the third conference in Hannover again in 2008. It is planned to carry out ESAR every two years also in the future. ESAR is a scientific colloquium and can be seen as a platform for exchange of information on accident research issues based on methodologies of investigation, injury mechanisms and injury assessment, accident causation and other issues of statistical accident data analysis. Representatives from authorities as well as from medical and technical institutions come together to discuss new research issues and exchange experiences on accident prevention and the complex field of accident reconstruction. Special focus was given to the target the European Union set for itself in 2000 which stipulates that within 10 years the number of person killed in road traffic accidents must be cut in half. To reach this goal, optimized measures, comprehensive research and analysis are necessary. A key hurdle comes from the European Union extension to 27 member states, each featuring different levels of traffic safety standards and different accident scenarios. Existing results from long term research projects in Europe, the USA, Australia and Japan including analyses of infrastructure, population, vehicle fleet and driver behaviour offer an excellent basis for understanding and improving countermeasures and research support needs in underdeveloped countries. ESAR's goal is to bring together researchers from all parts of the world, who will report on their methods and recommendations to improve traffic safety based on "In-Depth-Investigations" of real world accidents. These In-depth-investigations of accidents require thorough documentation and an accident data analysis on multidisciplinary levels which must be carried out immediately after it occurs. ESAR presents scientists the opportunity to present their studies on a common basis of research level.
Technical progress in automotive engineering focuses at the moment on two competing branches: improving safety and reducing energy consumption. Recent consideration has been given to a third factor, cost to the consumer. Challenges are presented by demographic changes, especially with increasing participation of elderly people in road traffic. The report considers the recent history of road accidents in Germany and statistics relating to vehicle population and road performance. There is a general trend towards decreasing numbers of accidents and their severity. Transport is responsible for roughly 20% of CO2 emissions and approximately 70% of total petroleum consumption. The Federal Government has responded to these challenges by publishing the Freight Transport and Logistics Masterplan in the summer of 2008. It describes the strategic transport policy direction and the key elements of the future course of action which are to be used to ensure the provision of efficient infrastructure and, at the same time, to reduce the amount of energy consumed by vehicles and make transport more efficient, cleaner and quieter. This document contains a number of concrete measures subsumed under the following six objectives: Making optimum use of transport infrastructure - shaping transport to make it more efficient; Reducing the number of journeys - ensuring mobility; Transferring more traffic to the railways and inland waterways; Upgrading more transport arteries and hubs; Environmentally friendly, climate friendly, quiet and safe transport, and Good working conditions and good training in the freight transport industry. Progress in research is outlined in the following areas: Daytime Running Lights for Motorcycles; Safety of hydrogen vehicles - addressing safety and environmental issues by development of a Global Technical Regulation for hydrogen vehicles; Elements of active vehicle safety for elderly drivers; Periodical Technical Inspection of electronically controlled systems in road vehicles - Electronic Stability Control; Pedestrian protection; Crash Compatibility - role of collision partner in passive safety tests; Child safety; Euro NCAP - Child Restraint Systems, and German Field Operational Test on Car-to-Car and Car-to-Infrastructure Systems (SIM-TD). The research project AKTIV - "Adaptive and Cooperative Technologies for Intelligent Traffic" encompasses the design, development, and evaluation of novel driver assistance systems, knowledge and information technologies and is set up to find solutions for efficient traffic management and Car-to-Car and Car-to-Infrastructure communication for future cooperative vehicle applications. The European Statement of Principles on the Human Machine Interface (HMI), presented at the eSafety Conference, which was held in Berlin on 5/6 June 2007, addresses issues such as Real Time Traffic Information (RTTI), Legal issues of Advanced Driver Assistance Systems (ADAS) and e-security.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
Impact severity is a fundamental measure for all in-depth crash investigation projects. One methodology used in the UK is based on the US Calspan software package CRASH3. The UK- in-depth crash investigation studies routinely use AiDamage3 a software package which is based on an updated version of the original CRASH3 algorithm, including enhancements to the vehicle stiffness coefficients. Real world accident-damaged vehicles are measured and their crush is correlated with a library of stiffness coefficients. These measurements are then used, along with other parameters, to calculate the crash energy and equivalent changes of velocity of the vehicles (delta-v), which is a measure of the impact severity. UK in-depth accident studies routinely validate the crash severity methodologies applied as the vehicle fleet changes. This is achieved by analysing crash test data and using the appropriate residual crush damage and other inputs to AiDamage3 and checking the program- outputs with the known crash severity parameters. This procedure checks, at least in part, the default stiffness values in the data libraries and the reconstruction methods used.
In the last years various new driver information and driver assistance systems made their way into modern vehicles and there are yet countless systems underway. However, expenses for both, the development and the construction of these systems are tremendous. Therefore the interest of evaluating systems keeps growing steadily, not only regarding the results of systems developed in the last years but also regarding system ideas. Only if at least a rough benefit estimation is given, the industry can decide which development should be supported. However, there is still a lack of transparency of possible and useful methods for these kinds of estimations. These were analyses and structured in this study.
The focus of the technical innovation in the automobile industry is currently changing to sensor based safety systems, which are operating in the pre-crash phase of an accident. To get more information about this pre-crash phase for real accidents a simulation of this phase using the GIDAS database is done. The basics for this simulation are geometrical information about the accident location and the exact accident data out of the GIDAS database. This aggregated information gives the possibility to simulate an exact motion for every accident participant, using MATLAB / SIMULINK, in the pre-crash phase. After the simulation the information about the geometrical positions, the velocities and maneuvers of the drivers to an individual TTC (time to collision) are available. With those results it is possible to develop new useful sensor geometries using pre-crash scatter plots or estimate the efficiency of implemented active safety systems in combination with sensor characteristics. This simulation can be done for every reconstructed accident included in the GIDAS database, so these results can represent a wide spread basis for the further development of active safety systems and sensor geometries and characteristics
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
The aim of this study was to evaluate the performance and accuracy of Event Data Recorders (EDRs). The analysis was based on J-NCAP crash tests from 2006"2007, with the corresponding EDR datasets. The pre-crash velocity, maximum delta-V and delta-V versus time history data recorded in the EDRs were compared with the reliable crash test data. The difference between the EDR pre-crash velocity and the laboratory test speed was less than 4 percent. In contrast, in several cases the maximum delta-V and delta-V versus time history data obtained from the EDRs showed uncertainty of measurement in comparisons with the reliable delta-V data. The difference in maximum delta-V in these comparisons was more than 5 percent in 10 of 14 tests and more than 10 percent in 4 of 14 tests. The EDRs underestimated the maximum delta-V in almost all tests. It was also concluded that the calculated acceleration from the EDR delta-V versus time history data showed good agreement with the instrumented accelerometer signal during the collision in almost all tests.
It has been pointed that most of the accidents on the roads are caused by driver faults, inattention and low performance. Therefore, future active safety systems are required to be aware of the driver status to be able to have preventative features. This probe study gives a system structure depending on multi-channel signal processing for three modules: Driver Identification, Route Recognition and Distraction Detection. The novelty lies in personalizing the route recognition and distraction detection systems according to particular driver with the help of driver identification system. The driver ID system also uses multiple modalities to verify the identity of the driver; therefore it can be applied to future smart cars working as car-keys. All the modules are tested using a separate data batch from the training sets using eight drivers" multi-channel driving signals, video and audio. The system was able to identify the driver with 100% accuracy using speech signals of length 30 sec or more and a frontal face image. After identifying the driver, the maneuver/ route recognition was achieved with 100% accuracy and the distraction detection had 72% accuracy in worst case. In overall, system is able to identify the driver, recognize the maneuver being performed at a particular time and able to detect driver distraction with reasonable accuracy.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 15. Oktober 2009 in Baden-Baden ihr 7. Symposium \"Sicher fahren in Europa\". Nach 1991, 1994, 1997, 2000, 2003 und zuletzt 2006 trafen sich auch dieses Mal wieder zahlreiche Fachleute aus Wissenschaft und Politik, Industrie, Wirtschaft und Verbänden aus dem In- und Ausland, trugen neue Forschungsergebnisse vor und erörterten aktuelle Ansätze zur Erhöhung der Verkehrssicherheit. Dabei ging es in den Referaten und Diskussionsbeiträgen und in den vier Workshops vor allem darum, die verkehrspolitischen Entwicklungen und Herausforderungen für die europäische Verkehrssicherheitsarbeit im Hinblick auf folgende Themen zu beleuchten: "Verkehrssicherheit Junger Fahrer", - Das "Auto der Zukunft", - "Demographischer Wandel", - "Landstraßensicherheit". Den Grundsatzreferaten folgten vertiefte Bearbeitungen in den Workshops. Die CD-ROM dokumentiert die Grußworte, Referate und Diskussionsbeiträge.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
Mit der EU-Verordnung Nummer 661/2009 zur Typgenehmigung und allgemeinen Sicherheit von Kraftfahrzeugen wird von der EU für schwere Nutzfahrzeuge der Einbau von Spurverlassenswarnsystemen und automatischen Notbremssystemen vorgeschrieben. Mit dem obligatorischen Einbau der Systeme wird eine Reduktion der Abkommens- und Auffahrunfälle von Nutzfahrzeugen aus den Klassen M2, M3, N2 und N3, die auf Grund der hohen Masse der Fahrzeuge folgenschwer sind, erwartet. Als Einführungsdaten werden der 1. November 2013 für neue Fahrzeugtypen und der 1. November 2015 für neue Fahrzeuge genannt. Leistungsanforderungen beziehungsweise technische Spezifikationen, denen die Systeme genügen müssen, liegen jedoch noch nicht vor. Diese werden derzeit von einer Expertengruppe auf UN-ECE-Ebene entwickelt. Dabei wird versucht, technologieneutrale Beschreibungen für die Ausgestaltung der Systeme zu erstellen, die gleichzeitig sowohl den gewünschten Nutzen für die Verkehrssicherheit garantieren, sich aber auch an der derzeit vorhandenen und realisierbaren Technologie orientieren. Darüber hinaus müssen die Systemkosten in einem vernünftigen Verhältnis zum Sicherheitsnutzen stehen. Ziel ist es, im Laufe des Jahres 2011 Vorschläge für die Legislative vorzulegen. Es wird über den Stand der Arbeiten, offene Fragestellungen, Herausforderungen bei der Ausgestaltung der technischen Anforderungen sowie sich abzeichnende Ergebnisse berichtet. Dabei sind die Arbeiten in Bezug auf Lane Departure Warning Systems (LDWS) bereits weiter fortgeschritten als zu Advanced Emergency Braking Systems (AEBS).
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.
Over the past two decades the popularity of consumer crash test programs, commonly referred to as New Car Assessment Programs (NCAP), has grown across the world. They are popular among government regulators as they afford a means of promoting safety innovations and levels of vehicle performance beyond those dictated by national standards. They also fulfill the demand for information regarding the safety ranking of vehicles among consumers contemplating the purchase of a new vehicle. There is no question that consumer crash test programs greatly influence vehicle design changes as well as accelerate the fitment of new safety features. The extent to which these changes can be expected to reduce serious and potentially fatal injuries will be influenced by how well the testing protocols and associated rating schemes correctly reflect the nature of the residual safety problem they seek to address. Drawing on data contained primarily in the US National Automotive Sampling System (NASS), the field relevance of current and proposed testing and rating protocols addressing frontal crash test protection is examined. Emphasis is placed on examining how accurately injury rates computed from the dummy responses measured in consumer crash tests correspond to actual injury rates observed in the field. Additional data from Canadian field investigations and US databases such as the National Motor Vehicle Crash Causation Survey (NMVCCS) are examined to see how well frontal airbag firing times, crush pulse durations and other determinants of injury are replicated in consumer testing protocols. This portion of the analysis draws on data obtained from Event Data Recorders (EDR) in both field collisions and staged tests of the same vehicle model. Vehicle rankings and overall frontal crash test ratings were found to be particularly sensitive to the choice of injury risk functions employed in the test. This was particularly true in the case of injury risk functions used to assess neck injury potential. Neck injury risk derived from Nij was found to show the least agreement with the field. Agreement between field chest injury rates and those derived from crash tests was improved considerably when chest injury risk functions for "older" occupants were employed. The paper concludes with a discussion of how different current testing protocols could be improved to enhance their field relevance.
Females sustain Cervical Spine Distortion injury (CSD) more often than males. Most work dealing with the biomechanics background (e.g. injury mechanism/criteria) as well as the application in seat design/testing, focuses on the occupant model of an average male. Therefore the EU-Project ADSEAT (Adaptive Seat to Reduce Neck Injuries for Female and Male Occupants) is aimed at adding a female model for gender balanced research of CSD and improving seat design. An extensive literature review, searching for risk factors and injury criteria for males and females, was accompanied by the evaluation of different databases containing CSD cases. The database evaluations suggests that an anthropometry quite close to the 50%ile female anthropometry as known from crash test dummy design is appropriate. The results presented here form the basis for the future development of a computational female model and the improvement of seat design for better protection of both males and females in the frame of the ADSEAT-Project.
The paper presents a methodology for the benefit estimation of several secondary safety systems for pedestrians, using the exceptional data depth of GIDAS. A total of 667 frontal pedestrian accidents up to 40kph and more than 500 AIS2+ injuries have been considered. In addition to the severity, affected body region, exact impact point on the vehicle, and the causing part of every injury, the related Euro NCAP test zone was determined. One results of the study is a detailed impact distribution for AIS2+ injuries across the vehicle front. It can be stated, how often a test zone or vehicle part is hit by pedestrians in frontal accidents and which role the ground impact plays. Basing on that, different secondary safety measures can be evaluated by an injury shift method concerning their real world effectiveness. As an example, measures concerning the Euro NCAP pedestrian rating tests have been evaluated. It was analysed which Euro NCAP test zones are the most effective ones. In addition, real test results have been evaluated. Using the presented methodology, other secondary safety like the active bonnet (pop-up bonnet) or a pedestrian airbag measures can be evaluated.
Accident data shows that the vast majority of pedestrian accidents involve a passenger car. A refined method for estimating the potential effectiveness of a technology designed to support the car driver in mitigating or avoiding pedestrian accidents is presented. The basis of the benefit prediction method consists of accident scenario information for pedestrian-passenger car accidents from GIDAS, including vehicle and pedestrian velocities. These real world pedestrian accidents were first reconstructed and the system effectiveness was determined by comparing injury outcome with and without the functionality enabled for each accident. The predictions from Volvo Cars" general Benefit Estimation Model are refined by including the actual system algorithm and sensing models for a relevant car in the simulation environment. The feasibility of the method is proven by a case study on a authentic technology; the Auto Brake functionality in Collision Warning with Full Auto Brake and Pedestrian Detection (CWAB-PD). Assuming the system is adopted by all vehicles, the Case Study indicates a 24% reduction in pedestrian fatalities for crashes where the pedestrians were struck by the front of a passenger car.
An eCall device has been mounted on some vehicles in France since 2003. It is an integrated car radio/GSM/GPS system that can be used with a SIM card. When an accident occurs, a call can be sent manually or automatically made to a telephone call centre. Knowing the geographic location, the vehicle identity and the possibility of a direct communication with the people involved enables the nearest emergency services to be called out. In this context, the LAB / CEESAR have set up a study aimed at evaluating the effectiveness of this system. The purpose of this paper is to detail the E-call system evaluation method of effectiveness used and give a global synthesis of the results.
This work aims at bringing evidence for mass incompatibility in frontal impact for cars built according to the UNECE R94 regulation. French national injury accidents database census for years 2005 to 2008 were used for the analysis. The heterogeneity of frontal self-protection among cars of different masses is investigated, as well as the partner protection parameter offered by these cars. The last part of the analysis deals with the estimation of the benefit, in terms of fatal and severe injuries avoided, if crashworthiness was harmonized for the whole fleet of vehicle. This calculation is done for France and is extended to all Europe.
The overall purpose of the ASSESS project is to develop a relevant and standardised set of test and assessment methods and associated tools for integrated vehicle safety systems, primarily focussing on currently available pre-crash sensing systems. The first stage of the project was to define casualty relevant accident scenarios so that the test scenarios will be developed based on accident scenarios which currently result in the greatest injury outcome, measured by a combination of casualty severity and casualty frequency. The first analysis stage was completed using data from a range of accident databases, including those which were nationally representative (STATS19, UK and STRADA, SE) and in-depth sources which provided more detailed parameters to characterise the accident scenarios (GIDAS, DE and OTS, UK). A common analysis method was developed in order to compare the data from these different sources, and while the data sets were not completely compatible, the majority of the data was aligned in such a way that allowed a useful comparison to be made. As the ASSESS project focuses on pre-crash sensing systems fitted to passenger cars, the data selected for the analysis was "injury accidents which involved at least one passenger car". The accident data analysis yielded the following ranked list of most relevant accident scenarios: Rank Accident scenario 1 Driving accident - single vehicle loss of control 2 Accidents in longitudinal traffic (same and opposite directions) 3 Accidents with turning vehicle(s) or crossing paths in junctions 4 Accidents involving pedestrians The ranked list highlights the relatively large role played by "accidents in longitudinal traffic", and "accidents with turning vehicle(s) or crossing paths in junctions" (the second and third most prevalent accident scenarios, respectively). The pre-crash systems addressed in ASSESS propose to yield beneficial safety outcomes with specific regard to these accident scenarios. This indicates that the ASSESS project is highly relevant to the current casualty crash problem. In the second stage of the analysis a selection of these accident scenarios were analysed further to define the accident parameters at a more detailed level .This paper describes the analysis approach and results from the first analysis stage.
An analysis of NASS and FARS was conducted to determine crash conditions that involved injuries that are not currently being directly addressed by vehicle safety standards or by consumer information test protocols. Analysis of both field data and US NCAP tests were conducted to determine the relative safety provided by seating position and by vehicle model year. Opportunities for improvements were determined by crash categories with large populations of injuries that were not addressed by safety tests or smaller numbers that were increasing in frequency. Areas of opportunities include improved occupant restrain in rollovers, improved frontal protection for rear seat occupants and improved fire prevention in frontal and rollover crashes.
The share of high-tensile steel in car bodies has increased over the last years. While occupant safety has generally benefited from this measure, there is a potential risk that, as a result, rescue time may increase considerably. In more than 60% of all car occupant fatalities a technical rescue has been necessary. These are in particular those cases where occupants die immediately at the accident scene. Therefore, in these cases "rescue time" is a very sensitive parameter. In addition to the general analysis of the need of technical rescue and the actual rescue time depending on model years, the injury pattern of occupants requiring technical rescue will be analysed to provide advice for rescue teams. Furthermore, a detailed analysis of rescue measures for the most popular car models depending on the safety cell design is given.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
Providing effective occupant protection in rollover crashes requires supplying the occupant with a restraint system proven effective in the dynamic rollover accident mode. Preventing ejection and providing restraint sufficient to prevent potentially injurious contacts with both interior and exterior vehicle components is paramount for effective rollover occupant protection. Research has shown that the injury potential can be decreased by closely coupling the occupant to the seat. This paper focuses on the effect of restraint system slack and its relationship to occupant excursion and ejection potential during rollover. Various restraint system configurations are evaluated in rollover-type test environments. A review of prior research is presented prior to presenting new quasi-static vehicle inversion studies conducted with live surrogate occupants. Additionally, dynamic rollover testing utilizing anthropometric test devices (ATDs) is presented. The influence of belt looseness and effects of various restraint designs on the belted occupants' injury potential are discussed.
In road traffic accidents, a car-seat and its occupant can be subjected to various crash pulses in the case of a rear impact. This study investigates the influence of crash pulse shape on seat-occupant response and evaluates the corresponding risk of whiplash injury. For this purpose, a rigorously validated seat-occupant system model is used to study different carseat designs and crash pulses. Two different car-seat concepts are also presented which can effectively mitigate whiplash injury for a wide range of crash severity. It is shown that for crash pulses of similar severity, the level of whiplash-risk depends strongly on the combined effects of seat design and crash pulse shape.