91 Fahrzeugkonstruktion
Filtern
Erscheinungsjahr
Dokumenttyp
Volltext vorhanden
- nein (133) (entfernen)
Schlagworte
- Sicherheit (58)
- Safety (57)
- Bewertung (40)
- Evaluation (assessment) (40)
- Vehicle (39)
- Fahrzeug (38)
- Anfahrversuch (34)
- Impact test (veh) (31)
- Conference (28)
- Test method (28)
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
The presence and performance of Advanced Driver Assistance Systems (ADAS) has increased over last years. Systems available on the market address also conflicts with vulnerable road users (VRUs) such as pedestrians and cyclists. Within the European project PROSPECT (Horizon2020, funded by the EC) improved VRU ADAS systems are developed and tested. However, before determining systems" properties and starting testing, an up-to-date analysis of VRU crashes was needed in order to derive the most important Use Cases (detailed crash descriptions) the systems should address. Besides the identified Accident Scenarios (basic crash descriptions), this paper describes in short the method of deriving the Use Cases for car-to-cyclist crashes. Method Crashes involving one passenger car and one cyclist were investigated in several European crash databases looking for all injury severity levels (slight, severe and fatal). These data sources included European statistics from CARE, data on national level from Germany, Sweden and Hungary as well as detailed accident information from these three countries using GIDAS, the Volvo Cars Cyclist Accident database and Hungarian in-depth accident data, respectively. The most frequent accident scenarios were studied and Use Cases were derived considering the key aspects of these crash situations (e.g., view orientation of the cyclist and the car driver- manoeuvre intention) and thus, form an appropriate basis for the development of Test Scenarios. Results Latest information on car-to-cyclist crashes in Europe was compiled including details on the related crash configurations, driving directions, outcome in terms of injury severity, accident location, other environmental aspects and driver responsibilities. The majority of car-to-cyclist crashes occurred during daylight and in clear weather conditions. Car-to-cyclist crashes in which the vehicle was traveling straight and the cyclist is moving in line with the traffic were found to result in the greatest number of fatalities. Considering also slightly and seriously injured cyclists led to a different order of crash patterns according to the three considered European countries. Finally the paper introduced the Use Cases derived from the crash data analysis. A total of 29 Use Cases were derived considering the group of seriously or fatally injured cyclists and 35 Use Cases were derived considering the group of slightly, seriously or fatally injured cyclists. The highest ranked Use Case describes the collision between a car turning to the nearside and a cyclist riding on a bicycle lane against the usual driving direction. A unified European dataset on car-to-cyclist crash scenarios is not available as the data available in CARE is limited, hence national datasets had to be used for the study and further work will be required to extrapolate the results to a European level. Due to the large number of Use Cases, the paper shows only highest ranked ones.
Die vorliegende Studie untersucht die Auswirkung der Ausstattung von Motorrädern mit Anti-Blockier-System (ABS) auf die Fahrsicherheit von Motorrädern. Hierzu wurden Fahrversuche im realen Verkehr und auf abgesperrter Teststrecke durchgeführt. Erfahrene und wenig erfahrene Motorradfahrer absolvierten Testfahrten auf nasser und trockener Fahrbahn mit und ohne ABS-Aktivierung des Motorrades. Bei den Versuchsfahrten kam es zu einigen kritischen Fahrsituationen, bei denen die Versuchspersonen insbesondere zu Beginn des Bremsmanövers von ihrem "normalen" Bremsverhalten abwichen. Bei blockierendem Hinterrad wurde der Bremsdruck vorne und hinten reduziert, was zu einer deutlichen Bremswegverlängerung führte. Bei den Vollbremsungen unter idealen Bedingungen auf abgesperrter Strecke wurden von erfahrenen Fahrern ohne ABS kürzere Bremswege als mit ABS erreicht. Kurvenbremsungen mit ABS-Regelung wurden im mittleren Geschwindigkeits- und Schräglagebereich fahrstabil durchgeführt. Die Ergebnisse zeigen, dass selbst erfahrene Motorradfahrer Bremsweg in kritischen Situationen verschenken. Geeignete Antiblockiersysteme könnten Motorradfahrern die Angst vor Radblockaden nehmen. Dies dürfte einen erheblichen Beitrag zur Steigerung der aktiven Sicherheit leisten.
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
Regarding to the German road traffic licensing regulations it is mandatory to have a light system using a bicycle in public traffic. All attached components must be approved. The admission requires additional restrictions such as a dynamo as energy source with a nominal voltage of 6 V. Batteries are only allowed in addition to this. To adopt the German bicycle regulation to the state of art of an energy efficient lighting, additional power sources such as a battery respectively rechargeable batterie should be evaluated. The project will propose amendments for German Road Traffic Regulations and technical requirements.
Erfahrungen in Deutschland mit der Anwendung der EU-Empfehlung "Europäischer Grundsatzkatalog zur Fahrer-Fahrzeug-Schnittstelle für Informations- und Kommunikationssysteme" werden beschrieben und daraus Konsequenzen abgeleitet. Insgesamt ist die ergonomische Bewertung der Mensch-Maschine-Schnittstelle von Fahrerinformations- und -Kommunikationssystemen nicht als einmaliges Ereignis, sondern als immer wieder zu durchlaufender Vorgang anzusehen, da neben neuen wissenschaftlichen Erkenntnissen jeweils neu entwickelte Geräte und Systeme zu berücksichtigen sind, was eine Anpassung der Grundsätze beziehungsweise eine Öffnung der Grundsätze für technische Neuerungen mit hohem Sicherheitsstandard erfordern könnte. Demonstrationen neuartiger Bedienkonzepte, Systementwicklungen und Arbeitstechniken sowie die hierzu durchgeführten Nutzertests verdeutlichen, dass ergonomisch sehr vielversprechende Lösungen (wie zum Beispiel Schnittstellen, die Eingaben mittels Gestik gestatten) existieren, beziehungsweise sich in der Entwicklung befinden. Diese Lösungen zeigen, dass die Empfehlung in weiten Bereichen technologieabhängig, das heißt, mit Blick auf Neuentwicklungen, nicht erschöpfend ist. Die Weiterentwicklung der Grundsätze sowie die Bewertung der sicheren Gestaltung der Mensch-Maschine-Schnittstelle bedarf nicht nur einer europaweit, sondern weltweit abgestimmten Vorgehensweise.
Der Autor berichtet über das neu eingerichtete Expertennetzwerk HUMANIST, das sich mit Fragen der nutzerorientierten und sicherheitsgerechten Gestaltung von Fahrerassistenz- und Informationssystemen befasst. Ziel sind die Zusammenführung und Integration entsprechender Forschungsaktivitäten auf europäischer Ebene.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
Anforderungen, Zielkonflikte
(2019)
Um Sicherheit und Umweltverträglichkeit von Straßen- bzw. Kraftfahrzeugen zu gewährleisten, werden an die Gestaltung der Fahrzeuge technische Anforderungen gestellt. Es gibt Anforderungen durch den Gesetzgeber, die erfüllt werden müssen, um ein Fahrzeug in den Verkehr bringen zu dürfen. Darüber hinaus bestehen herstellerinterne Anforderungen an das Produkt, die über das vom Gesetzgeber geforderte Maß hinausgehen, um den Kundenwünschen und der Firmenphilosophie zu genügen. Und als dritter Punkt stellen auch Verbraucherschutz-Organisationen Kriterien auf, anhand derer sie die Eigenschaften der auf dem Markt befindlichen Fahrzeuge bewerten und die Fahrzeuge eingruppieren, was dann der Kundeninformation dient. Auch diese Anforderungen gehen über die des Gesetzgebers hinaus. Das Setzen der gesetzlichen Mindestanforderungen ist für die Fahrzeugtechnik mittlerweile jedoch nicht mehr einzelnen Staaten überlassen. Vielmehr sind die für die Genehmigung von Fahrzeugtypen einzuhaltenden Bedingungen international harmonisiert: Für die EU sind dies EU-Richtlinien oder EU-Verordnungen, die von der Europäischen Kommission in Brüssel vorgeschlagen werden. Für über die EU hinausgehende Staaten bzw. Regionen sind dies unter anderem Regelungen der UN, erstellt von der UN-Wirtschaftskommission für Europa (UNECE) in Genf.
Thoracic injuries are one of the main causes of fatally and severely injured casualties in car crashes. Advances in restraint system technology and airbags may be needed to address this problem; however, the crash test dummies available today for studying these injuries have limitations that prevent them from being able to demonstrate the benefits of such innovations. THORAX-FP7 was a collaborative medium scale project under the European Seventh Framework. It focused on the mitigation and prevention of thoracic injuries through an improved understanding of the thoracic injury mechanisms and the implementation of this understanding in an updated design for the thorax-shoulder complex of the THOR dummy. The updated dummy should enable the design and evaluation of advanced restraint systems for a wide variety (gender, age and size) of car occupants. The hardware development involved five steps: 1) Identification of the dominant thoracic injury types from field data, 2) Specification of biomechanical requirements, 3) Identification of injury parameters and necessary instrumentation, 4) Dummy hardware development and 5) Evaluation of the demonstrator dummy. The activities resulted in the definition of new biofidelity and instrumentation requirements for an updated thorax-shoulder complex. Prototype versions were realised and implemented in three THOR dummies for biomechanical evaluation testing. This paper documents the hardware developments and biomechanical evaluation testing carried out.
Airbag-Systeme können, wie frühere Untersuchungen gezeigt haben, die passive Sicherheit von Motorrädern wirksam verbessern. Der vorliegende Forschungsbericht betrachtet die Übertragbarkeit von Pkw-Airbag-Konzepten auf das Motorrad und befasst sich vor allem mit dem Problem der motorradgerechten und sicheren Auslösung des Airbags. Die Funktion des Motorradairbags unterscheidet sich von der des Pkw-Airbags in entscheidender Weise durch die Möglichkeit, die Flugbahn des Fahrers bei einem Zusammenstoß mit einem rechtwinklig vor dem Motorrad befindlichen Pkw so zu beeinflussen, dass dieser das Hindernis ohne einen harten Anprall überfliegen kann. Der Abbau der kinetischen Energie des Fahrers geschieht so nicht in der kurzen Knautschzone vor dem Kollisionsobjekt, sondern in der meist ausreichend langen Auslaufzone dahinter. Der Motorradairbag kann am vorderen Tankbereich angebracht sein. Fülltechnik und Gewebematerial können vom Pkw direkt übernommen werden; jedoch ist die Nahtführung zu verstärken, da der Motorradairbag vorwiegend auf Scherung beansprucht wird. Gravierende Unterschiede ergeben sich in der Sensierung eines Crashs, da durch das an der Telegabel geführte Vorderrad signifikante Verzögerungsanstiege des Motorrades erst sehr spät erfolgen. Es ist daher nicht möglich, wie beim Pkw den Airbag allein über Beschleunigungsaufnehmer zu zünden. Schwerpunkt des Berichtes sind daher verschiedene Vorschläge, bei heute üblichen Motorradkonstruktionen einen Crash für eine Airbagauslösung rechtzeitig und sicher sensieren zu können. Zu charakteristischen Unfall-Ereignissen werden Sensoren nach verschiedenen Wirkprinzipien geordnet vorgestellt. Nach einer technischen Bewertung erweisen sich zwei Sensorvarianten als geeignet für eine zuverlässige Zündung des Airbag; gleichzeitig kann mit einer logischen Verknüpfung ihrer Signale eine Fehlauslösung sicher vermieden werden. Die ausgewählten und näher beschriebenen Sensoren registrieren den Druckanstieg im Vorderradreifen und die plastische Verformung der Telegabel. Damit ist eine Sensierung des Aufpralls rechtzeitig möglich. Je nach Größe und Dauer der Verzögerung kann der Druck des Luftkissens verändert werden, so dass der Motorradairbag in Abhängigkeit der Fahrgeschwindigkeit nur aufpralldämpfend oder flugbahnbeeinflussend wirkt. Testprogramme zur weiteren Entwicklung von Airbagsensoren für Motorräder werden als Forschungsbedarf näher erläutert.
Advancing active safety towards the protection of vulnerable road users: the PROSPECT project
(2017)
Accidents involving Vulnerable Road Users (VRU) are still a very significant issue for road safety. According to the World Health Organisation, pedestrian and cyclist deaths account for more than 25% of all road traffic deaths worldwide. Autonomous Emergency Braking Systems have the potential to improve safety for these VRU groups. The PROSPECT project (Proactive Safety for Pedestrians and Cyclists) aims to significantly improve the effectiveness of active VRU safety systems compared to those currently on the market by expanding the scope of scenarios addressed by the systems and improving the overall system performance. The project pursues an integrated approach: Newest available accident data combined with naturalistic observations and HMI guidelines represent key inputs for the system specifications, which form the basis for the system development. For system development, two main aspects are considered: advanced sensor processing with situation analysis, and intervention strategies including braking and steering. All these concepts are implemented in several vehicle prototypes. Special emphasis is put on balancing system performance in critical scenarios and avoiding undesired system activations. For system validation, testing in realistic scenarios will be done. Results will allow the performance assessment of the developed concepts and a cost-benefit analysis. The findings within the PROSPECT project will contribute to the generation of state -of-the-art knowledge, technical innovations, assessment methodologies and tools for advancing Advanced Driver Assistance Systems towards the protection of VRUs. The introduction of a new generation safety system in the market will enhance VRU road safety in 2020-2025, contributing to the "Vision Zero" objective of no fatalities or serious injuries in road traffic set out in the Transport White Paper. Furthermore, the test methodologies and tools developed within the project shall be considered for the New Car Assessment Programme (Euro NCAP) future roadmaps, supporting the European Commission goal of halving the road toll in the 2011-2020 timeframe.
The development of tyre- and truck-manufacturers leads to the direction to introduce wide base single tyres (size 495/45R22,5) instead of twin tyres on the driving axle of trucks, tractors and busses. To study the driving behaviour and safety of various trucks and units with different tyre combinations and loading conditions was the aim of the study. A computer-aided simulation was used for this investigation. Drive tests with a 40 t unit with prototype single tyres on the drive axle were carried out to verify the simulation. Alterations in driving behaviour and driving safety are mainly dependent on the tyre cornering stiffness. The prototype wide single tyres had a higher lateral stiffness which leads to a higher degree of under-steering (safer driving behaviour). The altered spring base on the drive axle had no influence on the side- tilt stability of vehicle combinations but the solo truck profited from the higher rear axle roll stiffness (less danger for roll-over accidents). As far as the driving safety is concerned nothing speaks against wide base tyres on the drive axle. The simulation of a tyre defect in a bend (assuming 40% of the max. transferable side force for the flat tyre) showed no increased danger using wide single tyres. Later driving tests showed however the need of tyre run flat possibilities to avoid jack-knifing of road trains. Also tyre pressure monitoring systems and electronic stability programs for the trucks are advised.
Accident analysis
(2014)
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the EC funded FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in today- research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The specific objectives of the work reported in this deliverable were: - Determine if previously identified compatibility issues are still relevant in current vehicle fleet: Structural interaction, Frontal force matching, Compartment strength in particular for light cars. - Determine nature of injuries and injury mechanisms: Body regions injured o Injury mechanism: Contact with intrusion, Contact, Deceleration / restraint induced. The main data sources for this report were the CCIS and Stats 19 databases from Great Britain and the GIDAS database from Germany. The different sampling and reporting schemes for the detailed databases (CCIS & GIDAS) sometimes do not allow for direct comparisons of the results. However the databases are complementary " CCIS captures more severe collisions highlighting structure and injury issues while GIDAS provides detailed data for a broader range of crash severities. The following results represent the critical points for further development of test procedures in FIMCAR.
Die Gestaltung der Interaktion zwischen den elektronischen "Infotainment"-Systemen im Auto und dem Fahrer gewinnt zunehmend an Bedeutung für die Verkehrssicherheit. Dem positiven Nutzen, den die Systeme hinsichtlich Fahrerunterstützung und Fahrkomfort aufweisen, stehen möglicherweise negative Auswirkungen auf die Fahrsicherheit gegenüber, wenn Ablenkung und Überlastung des Fahrers auftreten. Diesem Problemfeld widmete sich das EU-Projekt "Communication Multimedia Unit Inside Car" (COMMUNICAR), das im Juni 2003 abgeschlossen wurde. Hauptziel des Projekts waren die Entwicklung und Evaluierung eines Systems, das den Fahrer bei der Bewältigung der eingehenden Informationen unterstützt und eine zentrale Bedienmöglichkeit aufweist. Das COMMUNICAR-System enthält folgende wesentliche Elemente: Verschiedene Funktionen zu Telematikdiensten, Unterhaltung und zur digitalen Darstellung der traditionellen Informationen; eine als Informationsmanager (IM) bezeichnete regelbasierte Filterlogik sowie eine multimediale integrierte Mensch-Maschine-Schnittstelle (MMS) zur zentralen Bedienung und Informationsausgabe. In der ersten Phase der Entwicklung wurden die Nutzeranforderungen analysiert, die Funktionen definiert und die Ein-/Ausgabemodalitäten festgelegt. In der zweiten Phase wurden virtuelle Prototypen zur Gestaltung der MMS erarbeitet und diese in den anschließenden Nutzertest im Labor bewertet und ausgewählt. Die dritte Phase diente der Systementwicklung, bei der es vor allem um die Filterlogik des IM ging. Das System wurde zunächst im Fahrsimulator, anschließend unter Feldbedingungen getestet. Die Ergebnisse, die in den wesentlichen Einzelheiten berichtet werden, zeigten insgesamt ein positives Bild sowohl hinsichtlich der subjektiven Akzeptanzbewertung als auch hinsichtlich des Fahrverhaltens.
Abschluss des deutsch-französischen Verbundprojekts "Inter-Vehicle Hazard Warning" (DEUFRAKO-IVWH)
(2004)
Im Rahmen der Deutsch-Französischen Kooperation im Verbundprojekt "Inter-Vehicle Hazard Warning" (DEUFRAKO-IVWH) wurde ein auf Fahrzeug-Fahrzeug-Kommunikation basierendes Warnsystem konzipiert und bewertet. Die im Rahmen des Projekts durchgeführten Arbeiten haben gezeigt, dass ein auf Fahrzeug-Fahrzeug-Kommunikation basierendes Warnsystem prinzipiell geeignet ist, einen Beitrag zur Erhöhung der Verkehrssicherheit zu leisten. Das Ausmaß der zu erwartenden positiven Effekte ist allerdings ganz wesentlich abhängig vom Ausstattungsgrad der Fahrzeugflotte mit einem solchen System.
One main objective of the EU-Project SENIORS is to provide improved methods to assess thoracic injury risk to elderly occupants. In contribution to this task paired simulations with a THOR dummy model and human body model will be used to develop improved thoracic injury risk functions. The simulation results can provide data for injury criteria development in chest loading conditions that are underrepresented in PMHS test data sets that currently proposed risk functions are based on. To support this approach a new simplified generic but representative sled test fixture and CAE model for testing and simulation were developed. The parameter definition and evaluation of this sled test fixture and model is presented in this paper. The justification and definition of requirements for this test set-up was based on experience from earlier studies. Simple test fixtures like the gold standard sled fixture are easy to build and also to model in CAE, but provide too severe belt-only loading. On the other hand a vehicle buck including production components like airbag and seat is more representative, but difficult to model and to be replicated at a different laboratory. Furthermore some components might not be available for physical tests at later stage. The basis of the SENIORS generic sled test set-up is the gold standard fixture with a cable seat back and foot rest. No knee restraint was used. The seat pan design was modified including a seat ramp. The three-point belt system had a generic adjustable load limiter. A pre-inflated driver airbag assembly was developed for the test fixture. Results of THOR test and simulations in different configurations will be presented. The configurations include different deceleration pulses. Further parameter variations are related to the restraint system including belt geometry and load limiter levels. Additionally different settings of the generic airbag were evaluated. The test set-up was evaluated and optimized in tests with the THOR-M dummy in different test configurations. Belt restraint parameters like D-ring position and load limiter setting were modified to provide moderate chest loading to the occupant. This resulted in dummy readings more representative of the loading in a contemporary vehicle than most available PMHS sled tests reported in the literature. However, to achieve a loading configuration that exposes the occupant to even less severe loading comparable to modern vehicle restraints it might be necessary to further modify the test set-up. The new generic sled test set-up and a corresponding CAE model were developed and applied in tests and simulations with THOR. Within the SENIORS project with this test set-up also volunteer and PMHS as well as HBM simulations are performed, which will be reported in other publications. The test environment can contribute in future studies to the assessment of existing and new frontal impact dummies as well as dummy improvements and related instrumentation. The test set-up and model could also serve as a new standard test environment for PMHS and volunteer tests as well as HBM simulations.
Accidents between right turning trucks and straight driving cyclists often show massive consequences. Accident severity in terms of seriously or fatally injured cyclists that are involved is much higher than in accidents of other traffic participants in other situations. It seems clear that adding additional mirrors will very likely not improve the situation. At ESV 2015, a methodology to derive test procedures and first test cases as well as requirements for a driver assist system to address blind spot accidents has been presented. However, it was unclear if and how testing of these cases is feasible, to what extent characteristics of different truck concepts (e.g. articulated vehicles, rigid vehicles) influence the test conduction and outcome, and what tolerances should be selected for the different variables. This work is important for the acceptance of a draft regulation in the UN working group on general safety. In the meantime, three test series using a single tractor vehicle, a tractor-semitrailer combination and a rigid vehicle have been conducted. The test tools (e.g. surrogate devices) have been refined. A fully crashable, commercially available bicycle dummy has been tested. If used correct, this dummy does follow a straight line quite precisely and it does not cause any damage to the truck under test in case of accidental impact. The dummy specifications are freely available. During testing, the different vehicle categories resulted in different trajectories being driven. Articulated vehicle combinations did first execute a turn into the opposite direction, and on the other hand, single tractor vehicles did behave comparable to passenger cars. A possible solution to take these behaviors into account is to require the vehicles to drive through a corridor that is narrow for a precise straight-driving phase and extends during the turn. Other investigated parameters are the dummy and vehicle speed tolerances. The results from this research make it possible to draft a regulation for a driver assistance system that helps to avoid blind spot accidents: test cases have been refined, their feasibility has been checked, and corridors for the vehicles and for important parameters (e.g. test speeds) have been set. The test procedure is applicable to all types of heavy goods vehicles. In combination with the accidentology (ESV 2015 paper), the work provides the basis for a regulation for such an assistance system.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 15. Oktober 2009 in Baden-Baden ihr 7. Symposium \"Sicher fahren in Europa\". Nach 1991, 1994, 1997, 2000, 2003 und zuletzt 2006 trafen sich auch dieses Mal wieder zahlreiche Fachleute aus Wissenschaft und Politik, Industrie, Wirtschaft und Verbänden aus dem In- und Ausland, trugen neue Forschungsergebnisse vor und erörterten aktuelle Ansätze zur Erhöhung der Verkehrssicherheit. Dabei ging es in den Referaten und Diskussionsbeiträgen und in den vier Workshops vor allem darum, die verkehrspolitischen Entwicklungen und Herausforderungen für die europäische Verkehrssicherheitsarbeit im Hinblick auf folgende Themen zu beleuchten: "Verkehrssicherheit Junger Fahrer", - Das "Auto der Zukunft", - "Demographischer Wandel", - "Landstraßensicherheit". Den Grundsatzreferaten folgten vertiefte Bearbeitungen in den Workshops. Die CD-ROM dokumentiert die Grußworte, Referate und Diskussionsbeiträge.
Der Allgemeine Deutsche Automobil-Club e.V. (ADAC) und die Bundesanstalt für Straßenwesen (BASt) veranstalteten am 13. Oktober 2006 in Baden-Baden das 6. Symposium "Sicher fahren in Europa". Die Fachvorträge befassten sich mit den Themenbereichen: Ansätze zu mehr Verkehrssicherheit, - Verbesserung der Fahrzeugsicherheit, - Besondere Zielgruppen. Die CD-ROM dokumentiert die Grußworte, die Referate und die Podiumsdiskussion.
In 2012 the fifth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
Das Fahren mit Licht am Tag wird seit dem 1. Oktober 2005 vom damaligen Bundesministerium für Verkehr, Bau und Stadtentwicklung (BMVBS) empfohlen. Weiterhin wurde im Februar 2011 auf europäischer Ebene beschlossen, alle neuen Fahrzeugtypen der Fahrzeugklasse M1 (Fahrzeuge zur Personenbeförderung mit vier Rädern und maximal 8 Sitzplätzen außer dem Fahrersitz) sowie der Fahrzeugklasse N1 (Kraftfahrzeuge zur Güterbeförderung mit mindestens vier Rädern und mit einem zulässigen Gesamtgewicht bis zu 3,5 t) mit speziellen Tagfahrleuchten (TFL) auszustatten. Seit August 2012 gilt diese Regelung auch für alle anderen Fahrzeugklassen. Vor dem Hintergrund dieser Entwicklung wird davon ausgegangen, dass sich das Fahren mit Licht am Tag immer weiter verbreitet. Um daraus resultierende Sicherheitsgewinne bewerten zu können, ist eine kontinuierliche Beobachtung der Lichteinschaltquoten am Tag erforderlich. Die Grundidee der kontinuierlichen Erfassung der Lichteinschaltquoten am Tag mit der angewendeten Erhebungsmethodik wird beschrieben. Im Fokus stehen die neuen Qualitätssicherungsmaßnahmen. Abschließend werden die bisher ermittelten Zeitreihen analysiert.