Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (637) (entfernen)
Schlagworte
- Conference (386)
- Konferenz (382)
- Germany (212)
- Deutschland (209)
- Unfall (188)
- Accident (187)
- Safety (123)
- Sicherheit (122)
- Injury (117)
- Verletzung (117)
Institut
Due to the publication of guidelines in Germany the possibility exists to offer analytical designed construction works within an alternative proposal. But the extent to which the test specimen production influences the design relevant properties (for the same asphalt mixture) is not sufficiently investigated at present. Objective of this research project was to determine the design relevant asphalt properties by tests and do comparative considerations on two selected locations within the renewal of a federal trunk road (Germany). For the comparative consideration of the design relevant asphalt properties mixture samples were taken during paving and afterwards drill cores were taken at the same locations. Fatigue tests and tests to determine the stiffness were conducted with the Indirect Tensile Test (ITT). Then design calculations having regard to the test results were performed. At this different bearing conditions of the asphalt package were considered. The calculated fatigue conditions were comparative evaluated and they are presented and discussed in this paper.
Improving the security of critical road infrastructure is a major task for owners and operators of tunnels and bridges in the European TEN-T Network (Trans-European Networks of Transport) (European Parliament and Council 1996). Up to now, there has not been a systematic procedure for identifying and assessing critical infrastructure objects and selecting appropriate protection measures. The EC FP7 project SeRoN for the first time presents an innovative methodology in order to support road owners and operators in handling this complex task. This paper describes the methodology and project results in detail by giving an introduction into its practical application.
Für die rechnerische Dimensionierung der Betondecken im Oberbau von Verkehrsflächen für den Neubau sowie die Erneuerung nach RDO-Beton 09 ist die statische Spaltzugfestigkeit an der unteren beziehungsweise unteren und oberen Scheibe des Betonzylinders beziehungsweise Bohrkerns entsprechend der Vorgaben der AL Sp-Beton zu bestimmen. Aufgrund der unzureichenden Kenntnis der Präzision dieses Prüfverfahrens wurden mit einem breit aufgestellten Ringversuch die statistischen Kennwerte an Labor- und Bestandsbetonen unter Vergleichs- und Wiederholbedingungen auf der Grundlage des FGSV-Merkblatts über die statistische Auswertung von Prüfergebnissen ermittelt. Für eine möglichst gute statistische Absicherung nahmen an dem Ringversuch dreizehn erfahrene Prüfstellen teil. Zur Abdeckung des vielschichtigen Einsatzes des Prüfverfahrens erfolgte der Ringversuch an acht Prüflosen. Dabei berücksichtigen einerseits die Prüflose 1 und 2 mit den im Transportbetonwerk hergestellten Betonzylindern die Erst-/Eignungsprüfung und das darauf aufbauende Prüflos 3 mit Bohrkernen aus einer im Feldversuch hergestellten Fahrbahnplatte mit gleicher Betonrezeptur die Übereinstimmungskontrolle bei Neubaumaßnahmen. Andererseits findet der Einsatz des Prüfverfahrens bei der Restsubstanzbewertung von Betonfahrbahnplatten bei den Prüflosen 4 bis 7 mit den Bohrkernen aus vier in Waschbetonbauweise ausgeführten Fahrbahnplatten Berücksichtigung. Das zusätzlich aufgenommene Prüflos 8 mit einem Labormörtel dient der Herausarbeitung des Materialeinflusses auf die Präzision der Spaltzugfestigkeitsprüfung. Zusammenfassend kann festgestellt werden, dass die Präzision der in der AL Sp-Beton beschriebenen Spaltzugfestigkeitsprüfung mit einem Variationskoeffizienten von weniger als 10 % unter Wiederhol- und Vergleichsbedingungen hinreichend genau ist. Der geringe Unterschied zwischen den Variationskoeffizienten unter Wiederhol- und Vergleichsbedingungen lässt zusätzlich den Schluss zu, dass der Einfluss des unterschiedlichen Personals und der verschiedenartigen Prüftechniken bei den einzelnen Prüfstellen relativ gering ist. Die im Rahmen des Ringversuchs gewonnenen Erkenntnisse haben bereits partiell Eingang in die Normung gefunden.
Bitumen ist ein Erdölprodukt mit einer komplexen chemischen Zusammensetzung. Durch die Auswahl der zur Herstellung verwendeten Rohöle und die Art des Raffinerieprozesses werden die Zusammensetzung und die resultierenden chemisch-physikalischen Eigenschaften bestimmt. Für die Untersuchung von Bitumen steht heute eine Vielzahl von leistungsfähigen Methoden der modernen instrumentellen Analytik zur Verfügung. Das Hauptproblem bei der Analyse von Bitumen besteht in der Auftrennung des Stoffgemisches. Chromatographische Verfahren bieten generell die besten Voraussetzungen derartige Trennaufgaben zu bewältigen. So ermöglicht die TLC-FID-Methode die quantitative Bestimmung der Stoffgruppen der Aliphaten, Aromaten, Harze und Asphaltene. Dagegen ermöglicht die klassische Dünnschichtchromatographie, die in der Vergangenheit ausschließlich zum Nachweis von teerhaltigen Bindemitteln eingesetzt wurde, eine einfache und schnelle Möglichkeit eine chemische Charakterisierung von Bitumen in Form eines "Fingerprints" vorzunehmen. Dem Anspruch eine möglichst exakte und vollständige Beschreibung der chemischen Zusammensetzung von Bitumen zu erhalten, stehen Begrenzungen hinsichtlich der Wirtschaftlichkeit und Schnelligkeit der Verfahren gegenüber. Dennoch ist es möglich, mit einem relativ begrenzten Aufwand wertvolle Informationen über die chemische Beschaffenheit zu erhalten.
Die Kenntnis über den tatsächlichen strukturellen Zustand einer Asphaltbefestigung wird im Hinblick der stets steigenden Verkehrsbelastung und für eine qualifizierte Erhaltungsplanung immer wichtiger. In dem vorliegenden Beitrag wird ein Ansatz vorgestellt, welcher darin besteht, zu einem beliebigem Zeitpunkt anhand von versuchstechnisch ermittelten Asphaltkennwerten und aufbauend auf diesen Ergebnissen die Restnutzungsdauer einer Asphaltbefestigung zu prognostizieren. Hierfür wurden aus bestehenden Asphaltbefestigungen, welche bereits langjährig unter Verkehr liegen, Asphaltproben entnommen und deren asphaltspezifischen Eigenschaften wie die Steifigkeit und die Ermüdungsbeständigkeit versuchstechnisch bestimmt. Mit diesen Ergebnissen der Asphaltuntersuchungen im Labor und zusammen mit einem Prognoseverfahren in Anlehnung an die RDO Asphalt (FGSV 2009) besteht die Möglichkeit, Aussagen zu den voraussichtlichen Restnutzungsdauern von Asphaltbefestigungen geben zu können. Für die Optimierung dieser Vorgehensweise zur Prognose von Restnutzungsdauern wurde zu verschiedenen Zeitpunkten der gesamte Asphaltoberbau der Asphaltbefestigungen untersucht.
Offenporige Asphaltbeläge besitzen mit 22 % Hohlraum im Belag und einer groben Kornstruktur an der Oberfläche einen wesentlich anderen Aufbau als dichte Beläge. Nach vorliegenden Erfahrungen und Ergebnissen von durchgeführten Untersuchungen erfordern die Belagseigenschaften der offenporigen Asphaltbeläge eine andere Anwendung von Tausalz. Die Bundesanstalt für Straßenwesen (BASt) führte in den vergangenen Jahren gemeinsam mit der Firma KOMMZEPT-Ingenieurbüro Hausmann umfangreiche Untersuchungen zum Salzeinsatz auf offenporigen Belägen durch. Dazu gehörten Laborversuche, Messungen zur Verweil- und Wirkungsdauer von Tausalz auf diesen Belägen und Auswertungen der Beobachtungen von Autobahnmeistereien in Bayern, Brandenburg und Niedersachsen. Die Ergebnisse der Untersuchungen zeigen, dass die offenporigen Beläge teilweise winterdienstlich anders behandelt werden müssen als die dichten Beläge. Die Offenporigen Asphalte besitzen im Vergleich zu dichten Belägen eine deutlich rauere Oberflächenstruktur. In den Poren des Belags fließt Wasser nicht vollständig ab. Durch Kapillarwirkungen lagert sich Wasser im Belag ähnlich wie in einem Schwamm ab. Dieses Wasser im Belag kann durch den Verkehr sogar wieder zur Oberfläche gesaugt werden, an der es bei Temperaturen unter 0 -°C vor allem nachts zu einer Eisschicht kommen kann. Aufgrund der größeren gebundenen Wassermengen muss mehr Salz auf offenporigen Asphalten gestreut werden. Ausgebrachtes Tausalz bleibt länger in den Oberflächenporen oder im Belag haften. Es wird im Vergleich zu dichten Belägen durch den Verkehr fast nicht zur Seite verweht. Vorbeugend ausgebrachtes Feuchtsalz dringt langsam in die Oberfläche ein. An den eigentlichen Kontaktflächen zum Reifen bleibt wenig haften. Deshalb ist der Einsatz von Tausalzlösungen bei Reifglätte oder geringer Feuchte (Nieselregen) wirkungsvoller.
Various climate projections predict changing climatic parameters like temperature, precipitation, wind speed etc. for Germany. This could have severe impacts on road transport infrastructure as well as road traffic itself. At the Federal Highway Research Institute (Bundesanstalt für Straßenwesen (BASt) a strategy was developed to adapt roads and engineering structures to the impacts of climate change. The strategy "Anpassung der Straßenverkehrsinfrastruktur an den Klimawandel / Adaptation of the road infrastructure to climate change (AdSVIS)" comprises currently about 15 projects. On the basis of the identification of the hazards and the combination of the climate and road network data, the road transport infrastructure which might be affected is to be determined. Adaptation measures are to be developed for the identified risk areas and assessed as to their effectiveness. Special attention is given to international cooperation since climate change is a truly global challenge.
Tempered road system
(2014)
The road performance is strongly influenced by climatic conditions. Winter conditions have massive impact on traffic security but also pavement lifetime decreases as an effect of temperature variation during wintertime and summertime. Heating and cooling of a pavement is a possibility to work against these impacts. To discuss the boundary conditions for an efficient construction and operation of a tempered road system a feasibility study has been made. The study shows the feasibility and identifies thermal energy buffering as a main challenge. When thinking of a fully regenerative operation of a large tempered road system (e.g. 20.000 m-²) the storage volume has to be too large for an economic and structurally engineered satisfactory solution. However, the location dependent usage of natural geothermal storage possibilities and as well smart alignment and construction promises a feasibility realization.
The paper describes the development of transitions between different safety barriers in Germany but also in the context of the European standardization. In the paper practical and impact test expriences with transitions are shown. In view of the sheer number of theoretically possible combinations of safety barriers, the demand for testing every transition, even if the connecting safety barriers differ only slightly, appears to be economically unacceptable. On the other hand the experience from accidents and also from failed impact tests shows that transitions can be a risk to traffic safety. Therefore criteria for the distinction between transitions (impact test required/impact test unnecessary) are explained. In order to distinguish transitions which do not have to be impact-tested from those that require impact tests, criteria were developed and formulated.
Rural roads (highways) in Germany have to provide both high road safety and an appropriate level of service in accordance with their function in the road network. Single carriageway rural roads often underperform these expectations. An analysis of severe accidents on rural roads found two main contributing factors. First, high or inappropriate speed leads to accidents caused by the loss of control of the vehicle. Second, unsafe passing manoeuvres related to a misjudgement of sight distance, speed of oncoming vehicles or a misjudgement of the driver vehicle's acceleration capability. On the five roads where unsafe passing manoeuvres were a main contributing factor to accident occurrence, single short passing lanes (600 m to 1.2 km) were built to provide safe passing. On the remaining two-lane sections passing was prohibited by road signs and road marking. This paper investigates the effect of this design change on the accident situation and on traffic flow. The research project is based on a before/after comparison of traffic and accident data. Traffic volume, vehicle types and their velocities as well as the time gaps between the vehicles were recorded at different cross-sections. The result shows a significant improvement in road safety. This improvement was especially noted for severe head-on crashes, which were reduced to almost zero. The analysis of traffic flow on these roads pointed out that the chosen lengths of passing lanes were sufficient for safe passing and thereby reduced the need for dangerous driving behaviour. The recommendations of this research were fundamental for the determination of the design parameters of the second highest design class (EKL 2) in the new German Rural Road Design Guideline (RAL) published in spring 2013.
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
Bis zum Jahr 2000 erfolgte die Überarbeitung der Begutachtungsleitlinien zur Kraftfahrereignung stets als Gesamtwerk, in Zusammenarbeit mit den Fachgesellschaften und herausgegeben von einem Wissenschaftlichen Beirat. Diese Art der Veröffentlichung erwies sich aus verschiedenen Gründen als nicht mehr praktikabel. Von Anwenderseite wurde der Wunsch nach besserer Übersicht geäußert und es hat sich gezeigt, dass mehr Detailinformation erforderlich ist. Es wird auf die zukünftige Gestaltung und Veröffentlichung der Leitlinien eingegangen, die nun die kapitelweise Überarbeitung als Methode der Wahl definieren. Die freie Verfügbarkeit als elektronisches Dokument soll die Verbreitung weiter erhöhen, die Suche nach Begriffen vereinfachen und eine schnellere Aktualisierung ermöglichen. Änderungen bei der Europäischen Führerscheinrichtlinie (Annex III) sowie bei deren Umsetzung in Deutschland (Anlage 4 der Fahrerlaubnisverordnung) gingen Überarbeitungen bei verschiedenen Kapiteln der Begutachtungsleitlinien voraus. Schon seit 2009 veröffentlicht ist das überarbeitete Kapitel "Epilepsie". Es wird auf die Änderungen in den Kapiteln Diabetes, Tagesschläfrigkeit, Hörvermögen und Gleichgewicht eingegangen, die als nächste folgen sollen. Für den Abstimmungsprozess mit Bund und Ländern wurde das zukünftige Vorgehen bei Änderungsbedarf abgestimmt. Die Begutachtungsleitlinien sind kostenlos zum Download auf www.bast.de verfügbar, einschließlich ergänzender Informationen.
T. DÜNCHHEIM erörtert in seinem Einführungsvortrag zu "Die Stellung der Gemeinden im Straßenrecht" die kommunalen Gestaltungsspielräume hinsichtlich ihres Satzungsrechts, das sich auf -§ 19 StrWG NRW stützen lässt. Er schildert die Auswirkungen dieser Gestaltung auf das Straßen- und Straßenverkehrsrecht, die letztlich Ausfluss der gemeindlichen Selbstverwaltungsgarantie sind. Dabei problematisiert er die Abgrenzung zwischen straßenrechtlichem Gemeingebrauch und Sondernutzung sowie die Bedeutung der rechtlichen Ausgestaltung des Straßen- und Straßenverkehrsrechts. Hierbei wird die Anwendung des -§ 45 StVO durch die Gemeinden einer kritischen Analyse unterzogen. A. NETTER schildert in seinem Beitrag "Aktuelle Rechtsfragen der Ortsdurchfahrten" die Gremienstruktur im Straßenwesen und den Einfluss des Europarechts, des Bundes- und Landesstraßenrechts sowie den Ortsdurchfahrtenrichtlinien auf das Straßenwesen. Er stellt dabei die Folgen der Aufhebung der Radwegbenutzungspflicht sowie die aus der Straßenbaulast folgende Entwässerungsverpflichtung der Straßenbaulastträger und ihre Umsetzung in den Gemeinden dar. U. WEGNER berichtet in ihrem Beitrag "Aktuelle Entwicklungen des Verbandsklagerechts" über die Auswirkungen europäischer Richtlinien auf das Umweltrecht. In diesem Zusammenhang wird eine wegweisende Entscheidung des BVerwG erörtert, welche die direkte Anwendung des Art. 9 Abs. 3 AK zum Gegenstand hat. Trotz der Einführung einer bundesrechtlichen Verbandsklage in -§ 64 BNatSchG sei das Problem der Wahrung von Allgemeininteressen nicht gelöst, da diese Norm die Interessen des Umweltschutzes nicht hinreichend zu schützen vermöge. Der Beitrag "Inanspruchnahme öffentlicher Wege durch TK-Unternehmen" von U. STELKENS, stellt eine differenzierte Auseinandersetzung mit dem TKG-Wegerecht dar. Er konstatiert, dass die Bestimmungen des TKG im Wesentlichen auf den Normen des Telegraphenwegegesetz (TWG) basieren. Daher bestehen Spannungsverhältnisse und Reibungsflächen zwischen den verschiedenen Abschnitten des TKG, da das TKG und das TWG unterschiedliche Ziele verfolgen. Beispielsweise seien die -§ 77a bis -§ 77e TKG nicht auf die -§ 68 bis -§ 77 TKG abgestimmt worden. Der abschließende Beitrag "Fachplanerische Auswirkungen des Umweltschadensgesetzes" von M. PETERSEN widmet sich der Frage, ob und welche Auswirkungen das Umweltschadensgesetz auf das Fachplanungsrecht hat. Zunächst wird allgemein herausgearbeitet, dass das Umweltschadensgesetz nicht Schadensersatz- oder Ausgleichsleistungen eines geschädigten Dritten bezweckt; vielmehr sollen Umweltschäden vermieden und die Wiederherstellung geschädigter Umweltgüter erreicht werden. Die Frage, ob und inwieweit das Umweltschadensgesetz Auswirkungen auf das Fachplanungsrecht hat, hängt davon ab, ob die Haftungstatbestände des -§ 3 Abs. 1 USchadG einschlägig sind.
Structured road markings are becoming popular as edge line on high speed roads, ensuring night time visibility (retroreflection) during rain. These markings are often also "audio-tactile": vehicles (un)intentionally driving over it may produce much more tyre/road sound, which may be observed in the vehicle but also in the vicinity. The sound increase inside the car can be considered as a positive side effect, as it alarms the driver and may be very helpful for the prevention of "doze off" traffic accidents. The sound increase perceived outside the car however, may have a positive aspect as it can warn people on the emergency lane about the approaching vehicle, but it may as well annoy people living around. A method for the assessment of the acoustic properties of audio-tactile markings has been developed. It is mainly based on the "Close Proximity" (CPX) method, an ISO method intended for the acoustic assessment of pavements. The results of measurement campaigns with CPX trailers in Belgium and Germany according to a specially designed procedure are presented. The feasibility of the method is discussed. The research has been carried out in the frame of the standardization activities of the CEN working group CEN/TC226/WG2 "Horizontal signalization".
The use of alcohol interlocks for DUI offenders is widespread around the world. in North America and Australia alcohol interlocks are core elements in the countermeasure system against DUI recidivism. Based on a European experience exchange hosted by the Federal Highway Research Institute (BASt) in October 2013, key features of European alcohol interlock programmes are illustrated. In addition, key findings from international alcohol interlock research are presented. They point towards a need for an accompanying rehabilitative measure in order to achieve long-lasting behavioural changes in the offender. Data from the interlock recorder can be used as predictor for recidivism risk, but also as objective data to aid counselling. Finally, an example of an accompanying rehabilitative measure, which was specifically developed for interlock programmes within a BASt project, is given.
The German highway network is facing new challenges in the near future. The structures have to deal with increasing traffic loads, climate change effects and new requirements regarding sustainability while they are getting older and budget cuts can be expected. To guarantee a reliable highway network, it will be vital to adapt and enhance innovative approaches. Current bridge management relies on the results of conventional bridge inspections and thus has certain limitations when it comes to insufficient load bearing capacity and other systematic weaknesses. Therefore, new approaches for real time condition assessment of critical road infrastructure elements are to be developed.
In 2012 the fifth ESAR conference (Expert Symposium on Accident Research) was held in Hannover. ESAR is an international convention of experts, who analyze traffic accidents all over the world and discuss their results in this context, conducted at the Medizinische Hochschule Hannover every 2 years. It connected representatives of public authorities, engineers in automotive development and scientists and offers a forum with particular emphasis on In-Depth-Analyses of accident statistics and accident analyses. Special focus is placed on research on the basis of so-called "In-Depth-Accident-Investigations" [data collections at the sites of the accidents], which are characterized by extensive documentations of the sites of the accidents, of the vehicles as well as of the injuries, encompassing several scientific fields. ESAR aims at a multi-disciplinary compilation of scientific results and at discussing them on an international, scientific level. It is thus a scientific colloquium and a platform for exchanging information for all accident researchers. Experiences in accident prevention as well as in the complex field of accident reconstruction are stated and new research fields are added. Existing results of long-term research work in Europe, the US, Australia and Japan include different infrastructural correlations and give findings on population, vehicle population and driver characteristics, which offer a basis for recommendations to be derived and measures for increasing road safety.
The utilisation of secondary-safety systems to protect occupants has attained a very high level over the past decades. Further improvements are still possible, but increasingly minor progress is only to be had with a high degree of effort. Thus, a key aspect must be the impact to overall safety in an accident. If reliable information is available on an imminent crash, measures already taken in the pre-crash phase can result in a significantly great influence on the outcomes of the crash. With this background preventive measures are the key to a sustainable further reduction of the figures of crash victims on our roads. This paper aims to show a preventive approach that can contribute to lessening the consequences of a crash by creating an optimum interaction of measures in the fields of primary and secondary safety. To further enhance vehicle safety, driver assistant systems are already available that warn the driver of an imminent front-to-rear-end crash. The next step is to support him in his reactions or if he fails to react sufficiently, to even initiate an automatic braking when the crash becomes unavoidable. Automatic pre-crash braking can, in an ideal situation, fully prevent a crash or can significantly reduce the impact speed and thus the impact energy (and the severity of the accident). If a vehicle is being braked in the pre-crash phase, the occupants are already being pre-stressed by the deceleration. The information available about the imminent crash can be used to activate the belt tensioners and likewise other secondary safety systems in the vehicle right before the impact. The pre-crash deceleration also causes the front of the vehicle to dip. Conventional crash tests do not take this specific impact situation into consideration. This is why, for example, the influences of the pre-crash displacements of the occupants are not recorded in the test results. Furthermore, a reproducible representation of the benefit of the vehicle safety systems which prepare the occupants for the imminent impact is not possible. In order to demonstrate the functions of automated pre-crash braking and to investigate the differences during the impact as a consequence of the altered occupant positions as well as the initiation of force and deformations of the vehicle front, DEKRA teamed up with BMW to carry out a joint crash test with the latest BMW 5 series vehicle. It involved the vehicle braking automatically from a starting test speed of 64 km/h (corresponding to the impact speed set by Euro NCAP) down to 40 km/h. The test was still run by the intelligent drive system of the crash test facility. This required several modifications to be made to the test facility as well as to the vehicle. The paper will describe and discuss some relevant results of the crash test. In addition, the possible benefits of such systems will also be considered. The test supplemented the work of the vFSS working group (vFSS stands advanced Forward-looking Safety Systems).
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of synthetic and plastic materials as a material for the interior equipment of buses and coaches because of their ood mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years - also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, the production of smoke, the smoke development and propagation and its toxicity for the people as well as the testing methods and limit values are of interest. For those reasons research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behavior of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and on-board extinguishing equipment were elaborated. At the other hand research is carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. The paper describes which effective and economically reasonable fire safety requirements for interiors of buses would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses.