Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (70)
- Buch (Monographie) (45)
- Wissenschaftlicher Artikel (4)
- Bericht (1)
- Arbeitspapier (1)
Schlagworte
- Analysis (math) (121) (entfernen)
Institut
In Germany the number of casualties in passenger car to pedestrian crashes has been reduced by a considerable amount of 40% as regards fatalities and 25% with regard to seriously injured pedestrians since the year 2001. Similar trends can be seen in other European countries. The reasons for that positive development are still under investigation. As infrastructural or behavioral changes do in general take a longer time to be effective in real world, explanations related to improved active and passive safety of passenger vehicles can be more relevant in providing answers for this trend. The effect of passive pedestrian protection " specified by the Euro NCAP pedestrian test result " is of particular interest and has already been analyzed by several authors. However, the number of vehicles with some valid Euro NCAP pedestrian score (post 2002 rating) was quite limited in most of those studies. To overcome this problem of small datasets German National Accident Records have been taken to investigate a similar objective but now based on a much bigger dataset. The paper uses German National Accident Records from the years 2009 to 2011. In total 65.140 records of pedestrian to passenger car crashes have been available. Considering crash parameters like accident location (rural / urban areas) etc., 27.143 of those crashes have been classified to be relevant for the analysis of passive pedestrian safety. In those 27.143 records 7.576 Euro NCAP rated vehicles (post 2002 rating) have been identified. In addition it was possible to identify vehicles which comply with pedestrian protection legislation (2003/102/EG) where phase 1 came into force in October 2005. A significant correlation between Euro NCAP pedestrian score and injury outcome in real-life car to pedestrian crashes was found. Comparing a vehicle scoring 5 points and a vehicle scoring 22 points, pedestrians" conditional probability of getting fatally injured is reduced by 35% (from 0.58% to 0.37%) for the later one. At the same time the probability of serious injuries can be reduced by 16% (from 27.4% to 22.9%). No significant injury reducing effect, associated with the introduction of pedestrian protection legislation (phase 1) was detected. Considerable effects have also been identified comparing diesel and gasoline cars. Higher engine displacements are associated with a lower injury risk for pedestrians. The most relevant parameter has been "time of accident", whereas pedestrians face a more than 2 times higher probability to be fatally injured during night and darkness as compared to daytime conditions.
Within this paper different European accident data sources were used to investigate the causations and backgrounds of road traffic accidents with pedestrians. Analyses of high level national data and in-depth accident data from Germany and Great Britain was used to confirm and refine preliminary accident scenarios identified from other sources using a literature review. General observations made included that a high proportion of killed or seriously injured pedestrian casualties impacted by cars were in "dark" light conditions. Seven accident scenarios were identified (each divided into "daylight" and "dark" light conditions) which included the majority of the car front-to-pedestrian crash configurations. Test scenarios were developed using the identified accident scenarios and relevant parameters. Hypothetical parameters were derived to describe the performance of pedestrian pre-crash systems based on the assumption that these systems are designed to avoid false positives as a very high priority, i.e. at virtually all costs. As result, three "Base Test Scenarios" were selected to be developed in detail in the AsPeCSS project. However, further Enhanced Test Scenarios may be needed to address environmental factors such as darkness if it is determined that system performance is sensitive to these factors. Finally, weighting factors for the accident scenarios for Europe (EU-27) were developed by averaging and extrapolation of the available data. This paper represents interim results of Work Package 1 within the AsPeCSS project.
In general the passive safety capability is much greater in newer versus older cars due to the stiff compartment preventing intrusion in severe collisions. However, the stiffer structure which increases the deceleration can lead to a change in injury patterns. In order to analyse possible injury mechanisms for thoracic and lumbar spine injuries, data from the German Inâ€Depth Accident Study (GIDAS) were used in this study. A twoâ€step approach of statistical and caseâ€byâ€case analysis was applied for this investigation. In total 4,289 collisions were selected involving 8,844 vehicles, 5,765 injured persons and 9,468 coded injuries. Thoracic and lumbar spine injuries such as burst, compression or dislocation fractures as well as soft tissue injuries were found to occur in frontal impacts even without intrusion to the passenger compartment. If a MAIS 2+ injury occurred, in 15% of the cases a thoracic and/or lumbar spine injury is included. Considering AIS 2+ thoracic and lumbar spine, most injuries were fractures and occurred in the lumbar spine area. From the case by case analyses it can be concluded that lumbar spine fractures occur in accidents without the engagement of longitudinals, lateral loading to the occupant and/or very severe accidents with MAIS being much higher than the spine AIS.
Analysis of the accident scenario of powered two-wheelers on the basis of real-world accidents
(2013)
For the first time since 20 years the German national statistics of traffic accidents revealed an increasing number of fatalities and seriously injured persons in 2011. This negative development was especially caused by increasing numbers in all groups of vulnerable road users (VRU). Furthermore, the comparison of fatality reduction rates between several categories of road users shows that persons on motorcycles show the worst performance over years. Although every second fatality in German traffic accidents is still a car occupant, users of PTW make up more than 20% in the meantime. Assuming further improvements in the field of occupant protection this trend will continue. For that reason, a study on the basis of real-world accidents was conducted to describe the accident scenario involving motorcycles and to identify the reasons of the above-described fact. Approximately 1.800 motorcycle accidents out of GIDAS database were used for the analyses. The first part of the study deals with the question how representative the GIDAS database is for the German motorcycle accident scenario. Afterwards, detailed descriptive statistics on motorcycle accidents were presented considering numerous parameters about the accident scene, environmental influences, vehicle information, individual characteristics, interview data, injury severity and injury causation. One important point is the identification of the most frequent critical situations that are typical for motorcycle accidents. Furthermore, a special focus was on accident causation. Finally, conspicuous facts out of the analysis are emphasized. All in all, the study gives a comprehensive overview about the German motorcycle accident scenario. One the one hand, the use of weighted GIDAS data allows representative and robust statements on the basis of large case numbers; on the other hand highly detailed conclusions can be drawn. The results of the study help to understand the particularities of motorcycle accidents and provide approaches for further improvements in the field of PTW safety.
With an ever rising human life expectancy the share of elderly people in society is constantly rising. This leads to the fact that at the same rate the share of people with age related diseases such as dementia and poor eyesight taking part in traffic will rise and therefore traffic accidents caused by this group of people due to the disease will play an ever greater role. This Situation will be among the future challenges of road safety work. At present this study displays specific characteristics of accidents caused by elderly car drivers (aged 65 or higher) based on the analysis of the German In-Depth Accident Study GIDAS. Herein almost 1000 elderly car drivers were identified as accident participants in the years 2008 to 2011. The focus of this study lies on identifying special types of accidents which are caused by elderly drivers and on characterizing these types with the information gathered on scene and by interviewing the participants. The main evidence analyzed is the knowledge about the accident locality, the trajectories of the participants as well as the reasons for the occurrence of the accidents. Furthermore personal information such as the personal condition before the accident and driving purposes is used to identify patterns of contributing circumstances for accidents caused by elderly traffic participants.
The number of road accidents in Portugal has decreased significantly in the last decades, however, this tendency is not similar in all types of transportation. In the most recent years and by European standards, Portugal is still one of the leading countries concerning the number of fatalities in Powered Two Wheelers (PTW) accidents. To this effect, the in-depth investigation of PTW accidents is crucial and so, a thorough statistical analysis concerning the main factors influencing PTW riders injury severity accidents was undertaken regarding the 2007-2010 period in the National Road Safety Authority (ANSR) injured riders database using the software SPSS. In addition, to determine the importance of absent factors in the database analysis, such as velocity, a set of 53 real accidents involving PTW were also investigated and computationally reconstructed using the software PC-Crash. Lateral collisions between a motorcycle, its rider and the side of three different passenger cars were also simulated, varying the motorcycle impact angle and velocity in order to estimate the PTW deformation energy and the rider- injuries, as this accident configuration stands out in terms of frequency and even severity. The results of this detailed study are presented.
Nowadays human-created systems are increasing in complexity due to the interaction of humans and technology. Especially road traffic systems are composed of multitudinous resources (e.g. personnel, vehicles, organizations, etc.), which make it even harder to anticipate the positive and negative effects on safety. One key in achieving a significant reduction of fatalities is seen in driver assistant systems counterbalancing the lack of drivers' capabilities. But the actual outcome of implementing these sophisticated technologies especially on influencing driver's capabilities are yet unknown. Latest research exemplifies an increase of reaction times of drivers in case of dysfunctional driver assistant systems. This research paper applies STAMP/STPA (STAMP = systems-theoretic accident model and processes; STPA = systems-theoretic process analysis) to the German automobile traffic system focusing on the effects of driver assistant systems on drivers. By doing so, the potential hazards caused by technology can be identified.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
Die Untersuchung zum Forschungsprojekt FE 82.0499/2011 "Ausdehnung der Kostentragungspflicht des -§ 25a StVG auf den fließenden Verkehr" befasst sich mit der Thematik einer möglichen Ausdehnung der bislang ausschließlich für den ruhenden Verkehrs geltenden Kostentragungspflicht des -§ 25a StVG auf Verkehrsverstöße im fließenden Verkehr. Dieses Forschungsprojekt hatte die Aufgabenstellung zu erfüllen, aus der Arbeitspraxis der Bußgeldbehörden in den Bundesländern eine für die Ansprüche wissenschaftlicher Auswertungen qualitativ und quantitativ ausreichende Datenmenge zur Bearbeitung digital erfasster Geschwindigkeits-, Rotlicht- und Abstandsverstöße zu erheben. Dieser Gesamtdatenbestand sollte gesammelt, thematisch geordnet und hinsichtlich der einschlägigen Tatbestände sowie der Verfahrenseinstellungen aufbereitet werden. Hauptergebnis der Studie ist: - Bei einer Gesamtanzahl von 10,7 % eingestellter Bußgeldverfahren wird eine Anzahl von 2,5 % Bußgeldverfahren eingestellt, weil bei einem mittels digitaler Messtechnik beweissicher festgestellten Verkehrsverstoß und zweifelsfrei dokumentiertem Kfz-Kennzeichen der Fahrzeugführer trotz mindestens einer Ermittlungsmaßnahme nicht vor Eintritt der Verfolgungsverjährung ermittelt werden konnte.
Unfallgeschehen zwischen rechtsabbiegenden Güterkraftfahrzeugen und geradeausfahrenden Radfahrern
(2014)
Abbiege-Unfälle von Fahrzeugen, bei denen Radfahrer zu Schaden kommen, gehören zu den schweren Radfahrunfällen, insbesondere, wenn sie sich in einer "Tote Winkel"-Situation mit einem Güterkraftfahrzeug ereignen. Unklar ist die genaue Anzahl der Unfälle und die Unfallschwere, welche mit dieser Unfallkonstellation in Zusammenhang stehen können. In der Unfall-Analyse wurden dazu Daten der amtlichen Straßenverkehrsunfallstatistik der Jahre 2008 bis 2012 untersucht. Festgestellt wurde, dass diese Unfälle lediglich 1 % aller Radfahrunfälle sowie rund 6 % der insgesamt 406 getöteten Radfahrer darstellen. Durch eine weitere Differenzierung von "Tote Winkel"-Unfällen nach dem zulässigen Gesamtgewicht der Güterkraftfahrzeuge konnte festgestellt werden, dass die schweren Unfälle überwiegend geprägt sind von schweren Güterkraftfahrzeugen mit zulässigem Gesamtgewicht über 7,5 t sowie Sattelschleppern. Theoretisch wird bei jedem 10. "Tote Winkel"-Unfall zwischen einem rechtsabbiegenden, schwerem Güterkraftfahrzeug und einem geradeausfahrenden Radfahrer ungefähr ein Radfahrer getötet. Im laufenden Forschungsvorhaben "Toter Winkel " Konflikt zwischen rechtsabbiegenden Lkw und geradeausfahrendem Radverkehr" sollen die Verkehrssicherheitsdefizite analysiert werden. Des Weiteren wurde ein Forschungsvorhaben "Entwicklung eines Testverfahrens für Nutzfahrzeug-Abbiegeassistenzsysteme" initiiert, um eine Testkonfiguration für die Detektion von Radfahrern und die Warnung des Fahrzeugführers auf Basis von Unfallszenarien abzuleiten.
In Europe, in situ measurements of sound reflection and airborne sound insulation of noise barriers are usually done according to CEN/TS 1793-5. This method has been improved substantially during the EU funded QUIESST collaborative project. Within the same framework, an inter-laboratory test has been carried out to assess the repeatability and reproducibility of the newly developed method when applied to real-life samples, including the effect of outdoor weather variability and sample ageing. This article presents the statistical analysis of the inter-laboratory test results, and the values of the repeatability and the reproducibility, both in one-third octave bands and for the single-number ratings. The estimated reproducibility values can be used as the extended measure of uncertainty at the 95% credibility level in compliance with the ISO GUM. The repeatability and reproducibility values associated with airborne sound insulation are also compared with the corresponding values for laboratory measurements in building acoustics and an acceptable agreement is found.
Intelligente Bauwerke - Anforderungen an die Aufbereitung von Messgrößen und ihrer Darstellungsform
(2015)
Ziel des Forschungsvorhabens FE 15.0548/2011/GRB war die Ausarbeitung einer Konzeption zu Anforderungen an die Aufbereitung und Verarbeitung von Messgrößen und ihrer Darstellung. Dies beinhaltete die Evaluierung und Entwicklung verschiedener modellbasierter und statistischer Analyseverfahren, die über den bisherigen Stand der Technik der Bauwerksüberwachung hinausgehen. Der Nutzen liegt in der Herausfilterung relevanter Informationen aus umfangreichem Datenmaterial (Vor-Aggregation) sowie der Erzeugung von belastbaren Zustandsinformationen bzw. Vorergebnissen hierzu durch eine frühzeitige, leistungsfähige Plausibilisierung. Es wurde gezeigt, dass durch den Einsatz von leistungsfähigen, gedächtnisbehafteten, selbstlernenden Algorithmen für die Sensorfusion, Interpolation, Plausibilitätserhöhung und Treffen fachtechnischer Monitoringaussagen Ergebnisse erzielt werden können, die bezüglich der Verarbeitung von Mess- und Erfassungsdaten weit über den aktuellen Stand beim Brückenmonitoring hinausgehen. Anhand mehrerer Szenarien, für die reale Erfassungsdaten zur Verfügung standen, wurde gezeigt, dass diese Verfahren sehr zuverlässig verschiedenste Signalstörungen, wie Messausreisser, erhöhtes Rauschen und Brummeinstreuung erkennen können. Nur durch die frühzeitige und zuverlässige Plausibilisierung von Sensordaten von Brückenbauwerken kann verhindert werden, dass offensichtlich fehlerhafte Messwerte (wie z.B. Messausreisser, störungsbehaftete Messungen) zu falschen Vorhersagen der Systemzuverlässigkeit von Brückenbauwerken durch rechnergestützte Systemmodelle führen.
Abbiegeunfälle mit Kollisionen zwischen rechtsabbiegenden Güterkraftfahrzeugen und Fahrrädern haben in der Regel schwerwiegende Folgen für den ungeschützten Verkehrsteilnehmer. In der Vergangenheit wurde durch eine steigende Anzahl von Spiegeln das individuelle Sichtfeld des Lkw-Fahrers vergrößert und die Sicherheit für ungeschützte Verkehrsteilnehmer durch den Seitenunterfahrschutz verbessert. Da Abbiegeunfälle trotz der Vielzahl an Spiegeln auch heute noch geschehen, gleichzeitig aber Fahrerassistenzsysteme Einzug in viele Fahrzeugklassen gehalten haben, liegt es nahe, derartige Systeme für die Verhinderung von Abbiegeunfällen zu nutzen. Um entsprechende Systementwicklungen fördern zu können oder aber auch Systeme vorschreiben zu können, sind Anforderungen und passende Testmethoden für Abbiegeassistenzsysteme erforderlich. Ziel der BASt war es, solche Anforderungen und ein mögliches Testverfahren hierfür zu entwickeln. Ausgehend von Analysen des Unfallgeschehens wurden charakteristische Parameter und Begleitumstände von Unfällen zwischen Fahrrädern und rechtsabbiegenden Lkw identifiziert. Aus fahrdynamischen Überlegungen folgt bei den gegebenen Parametern, dass nur eine frühe, aber niederschwellige Fahrerinformation eine wirkungsvolle Assistenzfunktion zur Verhinderung der Unfälle sein kann. Für automatische Bremsungen gibt es bisher noch zu wenig Erfahrungen im Feld, und klassische, hochschwellige, aber sehr spät erfolgende Warnsignale würden durch die dann noch verstreichende Reaktionszeit keine rechtzeitige Bremsung des Lkw-Fahrers mehr hervorrufen. Basierend auf dem identifizierten Parameterraum, der zum komfortablen Anhalten erforderlichen Zeit und einem geeigneten Kinematikmodell lassen sich die räumlichen Bereiche um den Lkw definieren, in dem eine Umfelderkennung den Fahrradfahrer detektieren können muss, damit das Informationssignal durch das Assistenzsystem an den Lkw-Fahrer rechtzeitig ausgegeben wird. Aktuell wird davon ausgegangen, dass ein Abbiegeassistenzsystem, das die hier beschriebenen Prüfungen besteht, einen sehr positiven Einfluss auf das Unfallgeschehen zwischen rechtsabbiegenden Lkw und Fahrrädern haben wird.
Zur Ermittlung einer Mehr- oder Minderbeanspruchung des Straßenoberbaus durch Lang-Lkw wurde eine Stichprobe von 1.746 Fahrten im Direktverkehr und 483 Fahrten im kombinierten Verkehr analysiert. Die durchschnittliche Fahrzeuggesamtmasse der Lang-Lkw betrug 32,3 t. Ca. 9 % der Lang-Lkw fuhren überladen. Das Niveau der Überladungen lag jeweils unterhalb 3 t. Die maximale Achslast betrug 11,7 t. Die Achslastverteilung von Lang-Lkw im kombinierten Verkehr weist ein niedrigeres Niveau als für Lang-Lkw im Direktverkehr auf. Im Vergleich zu äquivalenten konventionellen Lkw ergibt sich für Lang-Lkw eine um 5 % niedrigere Anzahl äquivalenter 10-t-Achsen. Der mittlere Achszahlfaktor fA von Lang-Lkw beträgt 7,40. Das Transportvolumen eines Lang-Lkw entspricht rechnerisch dem Transportvolumen von 1,53 äquivalenten konventionellen Lkw. Mit zunehmendem Anteil Lang-Lkw am Gesamtkollektiv Schwerverkehr (bis zu 9 %) ist eine zunehmende, vergleichsweise geringe Reduzierung der B-Zahl nach RStO 12 zu verzeichnen, was in der Regel jedoch nicht zu einem Wechsel in die nächstkleinere Belastungsklasse führen würde. Mittels Dimensionierung nach RDO Asphalt 09 errechnet sich bei Einsatz von Lang-Lkw nach dem Ende einer 30-jährigen Nutzungsdauer der Straßenbefestigung ein geringfügig niedrigerer Ermüdungsstatus, der zu einer marginalen Verlängerung des Nutzungszeitraums führen würde. Der Einsatz von Lang-Lkw würde unter Einhaltung der im Feldversuch definierten fahrzeugtechnischen Vorgaben und zulässigen Grenzwerte für Fahrzeuggesamtgewichte und Achslasten nicht zur Mehrbeanspruchung des Oberbaus von Straßen führen. Die rechnerisch festgestellte Minderbeanspruchung des Oberbaus im Vergleich zu konventionellen Lkw hat nur marginale Bedeutung und würde sich somit in der Praxis kaum spürbar auf die Nutzungsdauer der Straßen auswirken.
The paper gives an overview of the recent (mostly 2012) figures of killed bus/coach occupants (drivers and passengers) in 27 Member States of the European Union as reported by CARE. The Evolution of the figures of bus/coach occupants killed in road accidents urban, rural without motorway and on motorways from 1991 to 2010 in 15 Member States of the EU supplements this information. More detailed are the figures reported for Germany by the Federal Statistics. The paper displays long-term evaluations (1957 to 2012) for killed, seriously and slightly injured occupants in all kinds of buses/coaches. Midterm evaluations (1995 to 2012) of the figures of fatalities and casualties are displayed for different busses according to their identification of road using as coaches, urban buses, school buses, trolley buses and "other buses". To be able to compare the evolutions of the safety of vehicle occupants it is customary to use different risk indicators. Calculations and illustrations for three often used indicators with their development over time are given: fatalities, seriously injured and slightly injured per 100,000 vehicles registered, per 1 billion (109) vehicle-kilometres travelled and per 1 billion (109) person-kilometres. These indicators are shown for occupants of cars, goods vehicles and buses/coaches. For the period from 1957 until 2012 it is obvious, that for all three vehicle categories analysed there was a clear long-term trend towards more occupant safety in terms of casualties per vehicles registered and per vehicle mileage. This was most significant for car occupants but it can be seen for bus/coach occupants and goodsvehicle occupants as well. Figures of killed occupants and of casualties related to person-kilometres are calculated and displayed for the shorter period 1995 to 2012. Here it becomes obvious that the bus/coach is still the safest mode of transport for the occupants of road vehicles. Graphs for the casualty risk indices still show significantly higher risks for car occupants despite the corresponding curve moved sustainable downwards. It is remarkable, that the risks of being killed or injured for the occupants of urban buses is growing whereas the corresponding risk for the occupants of coaches in line traffic tends downwards. The article ends with a short comparison and discussion of the risk indicators which are actually published for the occupants (driver and passengers) of cars and the passengers of buses/coaches, railroads, trams and airplanes. The interpretation of such information depends on the perception and it seems that for a complete view not only one indicator should be used and the evolutions of the indicator values during longer periods (as displayed with examples in the paper) should also be taken into account.
Enhanced protection of pedestrians and cyclists remains on the focus. Besides infrastructural and behavioral aspects it is necessary to exploit technical solutions placed on motorized vehicles. Accident research needs reliable data as well as national road accident statistics. Changing the view on seriously injured road users is one of the challenges which will substantially contribute to the optimization on future traffic safety. The missing accuracy in the definition of personal injury has a detrimental effect on making cost efficient road safety policy which is not only focused on fatal accidents. The European commission requested that, starting in 2015, all EU member states provide more detailed data on the injury status of road casualties, with special regard to the group of seriously injured. Conventional accident data will always be essential. But to obtain detailed data about driver behavior in real traffic situations further data sources are required. These could be EDR data, data from electronic control units, data from traffic surveys and traffic counting, naturalistic diving studies and field operational tests. Gaining insight into normal as well as critical driver behavior will enable accident researchers to deduct functions estimating the increase or decrease of accident risk associated with certain behaviors or vehicle functions. Also with view to the introduction of highly automated driving functions in the future such data is urgently needed. Computer simulation based tools to estimate the benefits of active safety systems are another step on the way towards the safety assessment of automated driving. It is now the duty of the scientific community to ask the right questions, to develop a methodology and to merge all these data sources into a common framework for the assessment of future traffic safety innovations.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
Ziel des Forschungsvorhabens war es zu untersuchen, ob in verschiedenen Prüfstellen mit dem Walzsektor-Verdichtungsgerät hergestellte Asphalt-Probeplatten gleiche Eigenschaften aufweisen, damit z.B. verträgliche Ergebnisse für Performance-Prüfungen ermittelt werden können. Dazu wurde in 12 Prüfstellen ein Verfahrens-Audit durchgeführt, um eine einheitliche Vorgehensweise bei der Herstellung dieser Platten zu gewährleisten. Anschließend wurden aus verschiedenen Asphaltvarianten WSV-Platten hergestellt und an daraus gewonnenen Probekörpern umfangreiche Performance-Prüfungen durchgeführt. Die ermittelten Ergebnisse zeigen, dass es möglich ist WSV-Platten mit verträglicher Raumdichte in unterschiedlichen WSV-Geräten sowie verschiedenen Prüfstellen herzustellen. Die Ergebnisse der Spurbildungs-, Druck-Schwell- und Zugversuche haben gezeigt, dass die WSV-Platten trotz ähnlicher Raumdichten nicht zwangsläufig verträgliche Ergebnisse im Versuch aufweisen und sich daher in verschiedenen Prüfstellen keine vergleichbaren Ergebnisse für diese Versuche ermitteln lassen. Lediglich bei den Abkühl- und Spaltzug-Schwellversuchen konnten verträgliche Ergebnisse erzielt werden. Für keine der ermittelten Kenngrößen der Performance-Prüfungen ließen sich Zusammenhänge mit der Raumdichte ermitteln. Somit lässt sich die Größe der Ergebnisse bei den Versuchen nicht auf unterschiedliche Größen der Raumdichten der Probekörper zurückführen. Da sich trotz geringer Unterschiede in den Raumdichten nur in ausgewählten Performance-Untersuchungen Unterschiede zeigen, ist davon auszugehen, dass die Streuungen in den Performance-Untersuchungen vornehmlich auf die Sensitivität dieser Versuche zurückzuführen sind. Das Verfahren zur Herstellung von Probekörpern für Performance-Prüfungen aus WSV-Platten scheint aufgrund der Gesamtheit der ermittelten Kenngrößen (Raumdichte, etc.), deren Aussehen, den Erkenntnissen aus dem Verfahrensaudit sowie der Performance-Prüfungen das richtige Verfahren zu sein.
Interdisciplinary accident research and research projects of AARU Audi Accident Research Unit
(2017)
AARU (Audi Accident Research Unit) is an interdisciplinary research project of the University Hospital Regensburg in cooperation with AUDI AG. Specific objective is to comprehend the respective accident scenario and retrieve generally applicable findings as to technical, medical and psychological processes. In order to prevent traffic accidents and to alleviate vehicle accident consequences, postulates of general traffic safety, human-machine interaction, technical design and function of new vehicles and occupant as well as third party protection shall be inferred from these findings. Specifically, each accident with new Audi, Lamborghini and Ducati vehicles involved is analyzed interdisciplinary, discussed in a case meeting and anonymously documented with more than 2,000 parameters. The database is continually used for solving safety relevant issues. Parallel to accident analysis, research projects are performed in the fields medicine, psychology and engineering in order to gain comprehensive insight and identify potential additional areas of activity of accident research.
Die Bundesanstalt für Straßenwesen (BASt) bringt zum Ende jeden Jahres eine Prognose der Unfall- und Verunglücktenzahlen des noch laufenden Jahres heraus, um so über die Entwicklung der Verkehrssicherheit in Deutschland Bilanz ziehen zu können. Dabei wird das Unfallgeschehen nach dem Schweregrad der Konsequenzen, der Ortslage sowie Alter und Art der Verkehrsbeteiligung der Verunglückten in 27 Zeitreihen unterteilt. Zu diesem Zeitpunkt sind die Daten lediglich für die ersten acht oder neun Monate erhältlich. Um Bilanz zu ziehen, werden die Anzahlen der letzten drei oder vier Monate prognostiziert. Gesamtziel des hier beschriebenen Forschungsvorhabens ist die Optimierung der jährlichen Unfallprognosen durch Anwendung von strukturellen Zeitreihenmodellen, bei denen die Vorhersagen aus dem Trend der vorliegenden Monate, und der Dynamik der vorhergehenden Jahre abgeleitet werden. Um dem Einfluss der Witterungsverhältnisse Rechnung zu tragen, werden dabei meteorologische Variablen in das Vorhersagemodell aufgenommen. Um die Modelle zu testen, werden die endgültigen Daten der letzten 15 Jahre jeweils aus den vorläufigen Daten der ersten Monate vorhergesagt und mit den tatsächlich beobachteten endgültigen Unfall- und Verunglücktenzahlen verglichen. Die Resultate zeigen, dass im Vergleich zu den bisherigen Vorhersagen mithilfe der hier vorgestellten Modelle die Vorhersagen für 25 der 27 Reihen präziser werden. Lediglich zwei Reihen zeigen einen leichten Anstieg des Vorhersagefehlers. Beim Vergleich von Modellen mit und ohne meteorologischen Variablen zeigt sich, dass 23 der 27 Reihen besser vorhergesagt werden können, wenn man das Wetter berücksichtigt. Neben der verbesserten Vorhersage ermöglicht die Aufnahme der Wettervariablen auch eine Einschätzung, wie groß der Einfluss der Witterungsgegebenheiten auf das Unfallgeschehen ist. Es zeigt sich also, dass die Anwendung von strukturellen Zeitreihenmodellen und die Berücksichtigung von meteorologischen Variablen zu einer deutlichen Verbesserung der Vorhersagegenauigkeit führen. Die Verbesserung der Vorhersagen durch die Aufnahme von Wettervariablen bestätigt nochmals den Einfluss der Witterungsumstände auf das Unfallgeschehen.