Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (121)
- Buch (Monographie) (73)
- Wissenschaftlicher Artikel (48)
- Arbeitspapier (14)
- Bericht (7)
- Teil eines Buches (Kapitel) (5)
Sprache
- Deutsch (140)
- Englisch (126)
- Mehrsprachig (2)
Schlagworte
- Safety (89)
- Sicherheit (89)
- Fahrzeug (65)
- Vehicle (64)
- Bewertung (59)
- Evaluation (assessment) (53)
- Deutschland (50)
- Germany (50)
- Versuch (49)
- Test method (46)
Institut
- Abteilung Fahrzeugtechnik (268) (entfernen)
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
The objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria and limits for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configurations such as impacts with car sides, trucks, and pedestrians. The WG consists of national government representatives who are supported by industrial advisers. The WG serves as a focal point for European research conducted by national and industry sponsored projects. The WG is responsible for collating the results from this research to achieve its objectives. EEVC WG 15 serves as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the Development of Crash Test Procedures"(VC-COMPAT) project partly funded by the European Commission. This paper presents a review of the current European research status. It also identifies current issues with candidate test procedures and lists the parameters that should be considered in assessing compatibility. The current candidate test procedures are: an offset barrier test with the progressive deformable barrier (PDB) face; a full width wall test with or without a deformable aluminium honeycomb face and a high resolution load cell wall; an offset barrier test with the EEVC barrier and load cell wall. These candidate test procedures must allow assessment of structural interaction, frontal force levels and compartment strength. The WG will report its findings to the EEVC Steering Committee and propose a test procedure in November 2006.
Bewertung der Fahrzeug-Fußraumintrusionen beim Offset Frontaltest gegen das Verformungselement
(1998)
In den Tests nach dem neuen Frontaltestverfahren (Entwürfe ECE R.94 sowie Richtlinie 96/79/EG und Ergänzung zu RL 70/156/EWG) entstehen hohe Verformungen der Fußräume der Versuchsfahrzeuge. Die Bewertung der Gefährdung der Insassen durch Intrusion, vorwiegend der Spritzwand begleitet von heftigen Bewegungen der Pedale, soll durch am Dummy zu messende Schutzkriterien erfolgen. Es ist vorgesehen, an den Dummies die Verschiebung des Schienbeins gegen das Knie, die Längskraft im Unterschenkel und den sogenannten Tibia Index zu messen. Um dieses zu ermöglichen, mussten an den vorhandenen Dummy-Unterschenkeln konstruktive Änderungen vorgenommen werden. Über die Herleitung der Schutzkriterien, Fragen bei der Anwendung dieser Kriterien sowie die technischen Einzelheiten und die Zertifizierung der neuen Dummy-Unterschenkel, welche die erforderlichen Messungen erlauben, wird berichtet.
Der Kraftschluss zwischen Reifen und Fahrbahn bestimmt in entscheidender Weise die Fahrsicherheit, insbesondere bei Nässe. Wer sein Fahrzeug mit breiteren Reifen ausrüsten will, hat oftmals keine Möglichkeit, die Eigenschaften der jeweiligen Reifen bei nachlassender Profiltiefe einzuschätzen. Es sollte in dieser Untersuchung geklärt werden, ob die Verwendung von Breitreifen Nachteile für die Fahrsicherheit bei Nässe mit sich bringt, insbesondere unter Berücksichtigung der im Betrieb zwangsläufig nachlassenden Profiltiefe. Im Innentrommelprüfstand der Bundesanstalt für Straßenwesen wurden Kraftschlussuntersuchungen an Pkw-Reifen in drei verschiedenen Breiten durchgeführt. Die Untersuchung beschäftigt sich mit dem Einfluss der Reifenbreite, der Profilgestaltung und der Profilhöhe auf den Kraftschluss bei Nässe. Dabei werden auch die Parameter Fahrgeschwindigkeit, Wasserfilmhöhe, Radlast und Reifeninnendruck berücksichtigt, die den Kraftschluss bei Nässe maßgeblich mitbestimmen. Steigende Fahrgeschwindigkeit, geringere Profiltiefe und höherer Wasserfilm verringern die maximal übertragbaren Bremskräfte. Höhere Radlasten verringern die Tendenz des Reifens, unter dem Druck des sich ausbildenden Wasserkeils aufzuschwimmen und verbessern dadurch das Kraftschlussverhalten bei Nässe. Niedrige Profilhöhen führen wegen der schlechter werdenden Wasserverdrängung zu einem stärkeren Abfall der Kraftschlussmaximalwerte bei steigender Geschwindigkeit oder höherem Wasserfilm. Insgesamt birgt die Kombination von hoher Fahrgeschwindigkeit, niedriger Profiltiefe und hohem Wasserfilm eine extrem hohe Aquaplaninggefahr, die sich noch verstärkt, wenn der korrekte Reifeninnendruck unterschritten wird. Bei niedrigen Fahrgeschwindigkeiten zeigen schmalere Reifen Vorteile, während bei höheren Fahrgeschwindigkeiten und niedrigen Wasserfilmhöhen Breitreifen das Niveau schmaler Reifen sogar übertreffen können. Dieser Effekt ist auf die spezielle laufrichtungsgebundene Profilgestaltung der hier untersuchten Breitreifen zurückzuführen.
Airbag-Systeme können, wie frühere Untersuchungen gezeigt haben, die passive Sicherheit von Motorrädern wirksam verbessern. Der vorliegende Forschungsbericht betrachtet die Übertragbarkeit von Pkw-Airbag-Konzepten auf das Motorrad und befasst sich vor allem mit dem Problem der motorradgerechten und sicheren Auslösung des Airbags. Die Funktion des Motorradairbags unterscheidet sich von der des Pkw-Airbags in entscheidender Weise durch die Möglichkeit, die Flugbahn des Fahrers bei einem Zusammenstoß mit einem rechtwinklig vor dem Motorrad befindlichen Pkw so zu beeinflussen, dass dieser das Hindernis ohne einen harten Anprall überfliegen kann. Der Abbau der kinetischen Energie des Fahrers geschieht so nicht in der kurzen Knautschzone vor dem Kollisionsobjekt, sondern in der meist ausreichend langen Auslaufzone dahinter. Der Motorradairbag kann am vorderen Tankbereich angebracht sein. Fülltechnik und Gewebematerial können vom Pkw direkt übernommen werden; jedoch ist die Nahtführung zu verstärken, da der Motorradairbag vorwiegend auf Scherung beansprucht wird. Gravierende Unterschiede ergeben sich in der Sensierung eines Crashs, da durch das an der Telegabel geführte Vorderrad signifikante Verzögerungsanstiege des Motorrades erst sehr spät erfolgen. Es ist daher nicht möglich, wie beim Pkw den Airbag allein über Beschleunigungsaufnehmer zu zünden. Schwerpunkt des Berichtes sind daher verschiedene Vorschläge, bei heute üblichen Motorradkonstruktionen einen Crash für eine Airbagauslösung rechtzeitig und sicher sensieren zu können. Zu charakteristischen Unfall-Ereignissen werden Sensoren nach verschiedenen Wirkprinzipien geordnet vorgestellt. Nach einer technischen Bewertung erweisen sich zwei Sensorvarianten als geeignet für eine zuverlässige Zündung des Airbag; gleichzeitig kann mit einer logischen Verknüpfung ihrer Signale eine Fehlauslösung sicher vermieden werden. Die ausgewählten und näher beschriebenen Sensoren registrieren den Druckanstieg im Vorderradreifen und die plastische Verformung der Telegabel. Damit ist eine Sensierung des Aufpralls rechtzeitig möglich. Je nach Größe und Dauer der Verzögerung kann der Druck des Luftkissens verändert werden, so dass der Motorradairbag in Abhängigkeit der Fahrgeschwindigkeit nur aufpralldämpfend oder flugbahnbeeinflussend wirkt. Testprogramme zur weiteren Entwicklung von Airbagsensoren für Motorräder werden als Forschungsbedarf näher erläutert.
Past European collaborative research involving government bodies, vehicle manufacturers and test laboratories has resulted in a prototype barrier face called the Advanced European Mobile Deformable Barrier (AE-MDB) for use in a new side impact test procedure . This procedure offers a better representation of the current accident situation and, in particular, the barrier concept is a better reflection of front-end stiffness seen in today- passenger car fleet compared to that of the current legislative barrier face. Based on the preliminary performance corridors of the prototype AE-MDB, a refined AE-MDB specification has been developed. A programme of barrier to load cell wall testing was undertaken to complete and standardise the AE-MDB specification. Barrier faces were supplied by the four leading manufacturers to demonstrate that the specification could be met by all. This paper includes background, specification and proof of compliance.
To assess occupant safety in a crash test, criteria associating the measurements made with a crash test dummy to injury risk are necessary. To enable better protection of elderly car occupants the objective of this study was to develop improved thoracic injury criteria for the THOR average male dummy. The development of these criteria is usually based on matched dummy and Post Mortem Human Surrogate (PMHS) tests by relating the obtained PMHS injuries to dummy measurements. This approach is limited, since only a few tests in relevant loading conditions are available and any new test series requires high efforts to be performed due to their complexity and costs. To overcome these limitations and to extend the dataset for the development of THOR dummy chest injury risk functions a simulation-based approach was applied within the EC funded project SENIORS (Safety Enhanced Innovations For older Road Users - www.seniors-project.eu). Within this study frontal impact sled simulations with an FE model representing a THOR average male dummy and matched simulations with a human body model (HBM) representing an elderly car occupant were carried out. The HBM used for this study was the THUMS TUC with modified rib cage, which was developed in SENIORS. The modifications included material and geometry changes aiming to represent an elderly car occupant. The rib fracture risk was predicted with a deterministic approach whereby a rib was considered broken when the strain exceeded an age-dependent threshold. Furthermore, a probabilistic method was applied to predict the probability of sustaining a certain number of fractured ribs by comparing local strain values to the distribution of cortical rib ultimate strain. By relating the output from the HBM simulations to a multi-point dummy injury criterion, injury risk curves were calculated by statistical methods. The wide range of loading conditions resulted in the desired range of injuries and THOR ATD output. The number of fractured ribs predicted by the HBM based on the deterministic prediction method was between 0 and 15. Furthermore, the probabilistic risk for the number of rib fractures equal or greater than two, three or four was calculated for each load case. The THOR rib deflection criterion Rmax was between 18 and 56 mm, while the PC Score was in the range of 2.5 to 7.2. Based on these outputs new risk curves for the predicted deterministic (AIS2+/3+) and probabilistic injury risk were calculated. The new curves show reasonable shapes and significance that provide trust in their application. The new risk curves are compared to risk curves obtained by traditional methods. The results were found similar to previous injury risk functions based on physical tests, which gives a high level of confidence in the chosen approach. The simulation-based approach of matched ATD model vs. HBM simulation was successfully applied. Rmax curves show a slightly better quality than the injury criterion PC Score.
Thorax injury is one of main causes of serious injury in frontal collisions, especially for elderly car occupants. The anthropometric test device (ATD) THOR‐M provides chest deflection measurements at multiple locations, to assess the risk of thorax injury. For this purpose e, risk functions are needed that relate the potential criteria based on multipoint chest deflection measurement to in jury risk. Different thorax injury criteria and risk functions for THOR have been proposed [2‐3]. The criteria and functions are based on the traditional approach to developing injury risk functions using matched ATD and PMHS tests by relating the injury (number of fractures) to injury criteria. Regarding these studies, some limitations have been identified, in particular concerning the loading conditions of the data used (mainly 3‐point‐belt loading, high loading severity, out‐of‐date ATD versions. To extend the data set and overcome these limitations, a new approach for improved thorax injury criteria was applied within the EC‐funded project SENIORS. The new approach is based on matched frontal impact sled computer simulations with a model representing the latest THOR‐M ATD version, and matching simulations with a human body model (HBM) representing an elderly car occupant.
For a number of EU regulatory acts Virtual Testing (VT) is already allowed for type approval (see Commission Regulation No. 371/2010 of 16 April 2010 amending the Framework Directive 2007/46/EC). However, only a very general procedure on how to apply VT for type approval is provided. Technical details for specific regulatory acts are not given yet. The main objective of the European project IMVITER (IMplementation of VIrtual TEsting in Safety Regulations) was to promote the implementation of VT in safety regulations. When proposing VT procedures the new regulation was taken into account, in particular, addressing open issues. Special attention was paid to pedestrian protection as pilot cases. A key aspect for VT implementation is to demonstrate that the employed simulation models are reliable. This paper describes how the Verification and Validation (V&V) method defined by the American Society of Mechanical Engineers was adapted for pedestrian protection VT based assessment. or the certification of headform impactors an extensive study was performed at two laboratories to assess the variability in calibration tests and equivalent results from a set of simulation models. Based on these results a methodology is defined for certification of headform impactor simulation models. A similar study was also performed with one vehicle in the type approval test setup. Its bonnet was highly instrumented and subjected to 45 impacts in five different positions at two laboratories in order to obtain an estimation of the variability in the physical tests. An equivalent study was performed using stochastic simulation with a metamodel fed with observed variability in impact conditions of physical headforms. An estimation of the test method uncertainty was obtained and used in the definition of a validation corridor for simulation models. Validation metric and criteria were defined in cooperation with the ISO TC22 SC10 and SC12 WG4 "Virtual Testing". A complete validation procedure including different test setups, physical magnitudes and evaluation criteria is provided. A detailed procedural flowchart is developed for VT implementation in EC Regulation No 78/2009 based on a so called "Hybrid VT" approach, which combines real hardware based head impact tests and simulations. This detailed flowchart is shown and explained within this paper. Another important point within the virtual testing based procedures is the documentation of relevant information resulting from the verification and validation process of the numerical models used. For this purpose report templates were developed within the project. The proposed procedure fixes minimum V&V requirements for numerical models to be confidently used within the type-approval process. It is not intended to be a thorough guide on how to build such reliable models. Different modeling methodologies are therefore possible, according to particular OEM know-how. These requirements respond to a balance amongst the type-approval stakeholders interests. A cost-benefit analysis, which was also performed within the IMVITER project, supports this approach, showing the conditions in which VT implementation is beneficial. Based on the experience gained in the project and the background of the experts involved an outlook is given as a roadmap of VT implementation, identifying the most important milestones to be reached along the way to a future vehicle type approval procedure supported by VT. The results presented in this paper show an important step addressing open questions and fostering the future acceptance of virtual testing in pedestrian protection type approval procedures.
Upcoming test procedures and regulations consider the use of Q-dummies. Especially Q6 and Q10 will be introduced to assess the safety of child occupants in vehicle rear seats. Therefore detailed knowledge of these dummies is important to improve safety. As recent studies have shown, chest deflection measurements of both dummies are influenced by parameters like belt geometry. This could lead to a non optimized design of child restraint systems (CRS) and belt systems. The objective of this study is to obtain a more detailed understanding of the sensitivity of chest measurements to restraint parameters and to investigate the possibilities of chest acceleration as an alternative for the assessment of chest injury risks. A study of frontal impact sled tests was performed with Q6 and Q10 in a generic rear seat environment on a bench. Belt parameters like modified belt attachment locations were varied. For the Q6 dummy, different positioning settings of the CRS (booster with backrest) and of the dummy itself were investigated. The Q10 dummy was seated on a booster cushion. Here the position of the upper belt anchorage point was varied. To simulate the influence of vehicle rotation in the ODB crash configuration, the bench was pre-rotated on the sled in additional tests with the Q10. This configuration was tested with and without pretensioner and load limiter. Chest deflection in Q6 showed a high sensitivity to changes in positioning of the CRS and the dummy itself. A more slouched position of the CRS or dummy resulted in a reduction of measured chest deflection, whereas chest acceleration increased for a more slouched position of the CRS. Chest deflection in Q10 is sensitive to belt geometry as already shown in other studies. In a more outboard position of the shoulder belt anchorage the measured chest deflection is higher. Chest acceleration shows the opposite tendency, which is highest for the rearmost location of the upper belt anchorage. On a pre-rotated bench the highest chest deflection within this test series was observed without load limiter/pretensioner and an outboard belt position. By optimizing the belt location and the use of pretensioner/load limier the chest deflection was significantly reduced. For the Q6 a criterion based on chest acceleration as well as deflection measured at two locations might be the most reliable approach, which requires further research with an additional upper deflection sensor. In the Q10 the measured chest deflection does not always correctly reflect the severity of chest loading. The deflection is depending on initial belt position and restraint parameters as well as test conditions, which result in different directions of belt migration. A3ms chest acceleration might be a better indicator for severity of chest loading independent of different conditions like belt geometries. However, in some cases the benefit of an optimized restraint system could only be shown by deflection. These findings suggest that further research is needed to identify a chest injury assessment method, which could be based on deflection as well as acceleration or other parameters related to belt to occupant interaction.