620 Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
Dokumenttyp
- Arbeitspapier (23) (entfernen)
Schlagworte
- Bewertung (9)
- Fahrzeug (9)
- Safety (9)
- Vehicle (9)
- Evaluation (assessment) (8)
- Impact test (veh) (8)
- Method (8)
- Sicherheit (8)
- Verfahren (8)
- Anfahrversuch (7)
Anhand von zwei verschiedenen Versuchskonfigurationen wurde das Schutzpotential von Kopfschutzsystemen (Fahrradhelm und airbagbasiertes System) untersucht. Hierbei wurden die resultierende Kopfbeschleunigung als Messwert sowie das Kopfverletzungskriterium HIC bei Versuchen ohne und mit Kopfschutzsystem vergleichend gegenübergestellt.
The objective of this deliverable is to describe the expected influence of the candidate test procedures developed in FIMCAR for frontal impact on other impact types. The other impact types of primary interest are front-to-side impacts, collisions with road restraint systems (e.g. guardrails), and heavy goods vehicle impacts. These collision types were chosen as they involve structures that can be adapted to improve safety. Collisions with vulnerable road users (VRU) were not explicitly investigated in FIMCAR. It is expected that the vehicle structures of interest in FIMCAR can be designed into a VRU friendly shell. Information used for this deliverable comes from simulations and car-to-car crash tests conducted in FIMCAR or review of previous research. Three test configurations (full width, offset, and moving deformable barriers) were the input to the FIMCAR selection process. There are three different types of offset tests and two different full width tests. During the project test procedures could be divided into three groups that provide different influences or outcomes on vehicle designs: 1. The ODB barrier provides a method to assess part of the vehicles energy absorption capabilities and compartment test in one test. 2. The FWRB and FWDB have similar capabilities to control structural alignment, further assess energy absorption capabilities, and promote the improvements in the occupant restraint system for high deceleration impacts. 3. The PDB and MPDB can be used to promote better load spreading in the vehicle structures, in addition to assessing energy absorption and occupant compartment strength in an offset configuration. The consortium selected the ODB and FWDB as the two best candidates for short term application in international rulemaking. The review of how all candidates would affect vehicle performance in other impacts (beside front-to-front vehicle or frontal impacts with fixed obstacles) however is reported in this deliverable to support the benefit analysis reported in FIMCAR. The grouping presented above is used to discuss all five test candidates using similarities between certain tests and thereby simplify the discussion.
The objectives of the FIMCAR (Frontal Impact and Compatibility Assessment Research) project are to answer the remaining open questions identified in earlier projects (such as understanding of the advantages and disadvantages of force based metrics and barrier deformation based metrics, confirmation of specific compatibility issues such as structural interaction, investigation of force matching) and to finalise the frontal impact test procedures required to assess compatibility. Research strategies and priorities were based on earlier research programs and the FIMCAR accident data analysis. The identified real world safety issues were used to develop a list of compatibility characteristics which were then prioritised within the consortium. This list was the basis for evaluating the different test candidates. This analysis resulted in the combination of the Full Width Deformable Barrier test (FWDB) with compatibility metrics and the existing Offset Deformable Barrier (ODB) as described in UN-ECE Regulation 94 with additional cabin integrity requirement as being proposed as the FIMCAR assessment approach. The proposed frontal impact assessment approach addresses many of the issues identified by the FIMCAR consortium but not all frontal impact and compatibility issues could be addressed.
Accident analysis
(2014)
For the assessment of vehicle safety in frontal collisions compatibility (which consists of self and partner protection) between opponents is crucial. Although compatibility has been analysed worldwide for years, no final assessment approach has been defined to date. Taking into account the European Enhanced Vehicle safety Committee (EEVC) compatibility and frontal impact working group (WG15) and the EC funded FP5 VC-COMPAT project activities, two test approaches have been identified as the most promising candidates for the assessment of compatibility. Both are composed of an off-set and a full overlap test procedure. In addition another procedure (a test with a moving deformable barrier) is getting more attention in today- research programmes. The overall objective of the FIMCAR project is to complete the development of the candidate test procedures and propose a set of test procedures suitable for regulatory application to assess and control a vehicle- frontal impact and compatibility crash safety. In addition an associated cost benefit analysis should be performed. The specific objectives of the work reported in this deliverable were: - Determine if previously identified compatibility issues are still relevant in current vehicle fleet: Structural interaction, Frontal force matching, Compartment strength in particular for light cars. - Determine nature of injuries and injury mechanisms: Body regions injured o Injury mechanism: Contact with intrusion, Contact, Deceleration / restraint induced. The main data sources for this report were the CCIS and Stats 19 databases from Great Britain and the GIDAS database from Germany. The different sampling and reporting schemes for the detailed databases (CCIS & GIDAS) sometimes do not allow for direct comparisons of the results. However the databases are complementary " CCIS captures more severe collisions highlighting structure and injury issues while GIDAS provides detailed data for a broader range of crash severities. The following results represent the critical points for further development of test procedures in FIMCAR.
The off-set assessment procedure potentially contributes to the FIMCAR objectives to maintain the compartment strength and to assess load spreading in frontal collisions. Furthermore it provides the opportunity to assess the restraint system performance with different pulses if combined with a full-width assessment procedure in the frontal assessment approach. Originally it was expected that the PDB assessment procedure would be selected for the FIMCAR assessment approach. However, it was not possible to deliver a compatibility metric in time so that the current off-set procedure (ODB as used in UNECE R94) with some minor modifications was proposed for the FIMCAR Assessment Approach. Nevertheless the potential to assess load spreading, which appears not to be possible with any other assessed frontal impact assessment procedure was considered to be still high. Therefore the development work for the PDB assessment procedure did not stop with the decision not to select the PDB procedure. As a result of the decisions to use the current ODB and to further develop the PDB procedure, both are covered within this deliverable. The deliverable describes the off-set test procedure that will be recommended by FIMCAR consortium, this corresponds to the ODB test as it is specified in UN-ECE Regulation 94 (R94), i.e. EEVC deformable element with 40% overlap at a test speed of 56 km/h. In addition to the current R94 requirements, FIMCAR will recommend to introduce some structural requirements which will guarantee sufficiently strong occupant compartments by enforcing the stability of the forward occupant cell. With respect to the PDB assessment procedure a new metric, Digital Derivative in Y direction - DDY, was developed, described, analysed, and compared with other metrics. The DDY metric analyses the deformation gradients laterally across the PDB face. The more even the deformation, the lower the DDY values and the better the metric- result. In order analyse the different metrics, analysis of the existing PDB test results and the results of the performed simulation studies was performed. In addition, an assessment of artificial deformation profiles with the metrics took place. This analysis shows that there are still issues with the DDY metric but it appears that it is possible to solve them with future optimisations. For example the current metric assesses only the area within 60% of the half vehicle width. For vehicles that have the longitudinals further outboard, the metric is not effective. In addition to the metric development, practical issues of the PDB tests such as the definition of a scan procedure for the analysis of the deformation pattern including the validation of the scanning procedure by the analysis of 3 different scans at different locations of the same barrier were addressed. Furthermore the repeatability and reproducibility of the PDB was analysed. The barrier deformation readings seem to be sensitive with respect to the impact accuracy. In total, the deliverable is meant to define the FIMCAR off-set assessment procedure and to be a starting point for further development of the PDB assessment procedure.
Der vom 01.01.2012 bis zum 31.12.2016 andauernde Feldversuch der Bundesregierung mit Lang-Lkw wird durch die Bundesanstalt für Straßenwesen (BASt) wissenschaftlich begleitet. Lang-Lkw sind Fahrzeuge und Fahrzeugkombinationen, - die mit bis zu 25,25 m zwar länger als nach den geltenden Regelungen ausgeführt sein dürfen, - im Vergleich zu herkömmlichen Lkw um bis zu 6,50 m länger sind, - aber kein höheres Gesamtgewicht als die auch heute schon geltenden 40 t beziehungsweise 44 t im Vor- und Nachlauf zum Kombinierten Verkehr haben. Im Feldversuch werden die Chancen und Risiken des Einsatzes der Lang-Lkw untersucht. Nach etwa der Hälfte des Feldversuchs wurden die wesentlichen Erkenntnisse aus dem bisherigen Untersuchungszeitraum in einem Zwischenbericht von der BASt zusammengefasst und bewertet. Der Zwischenbericht der BASt gliedert sich thematisch und enthält neben den für die Konzeption der Gesamtuntersuchung erforderlichen rechtlichen Grundlagen und vorliegenden Erkenntnissen aus der Literatur insbesondere die Zusammenfassungen verschiedener Forschungsprojekte zu den hinsichtlich des Einsatzes von Lang-Lkw relevanten Fragestellungen. Die Teilprojekte, die von externen Forschungsnehmern bearbeitet wurden, sind als selbstständige Publikationen verfügbar. Dort finden sich detailliertere Informationen zu den einzelnen Untersuchungen. Insgesamt galt es herauszuarbeiten, welche Auswirkungen der Einsatz von Lang-Lkw im Vergleich zur Situation ohne Lang-Lkw auf die identifizierten Fragestellungen hat. Zusammenfassend lässt sich feststellen, dass sich neben den festgestellten positiven Effekten, wie einem Effizienzgewinn und der Einsparung von Lkw-Fahrten, gravierende Probleme im Feldversuch unter den gegebenen Randbedingungen bislang nicht gezeigt haben. Gemessen an der Vielzahl betrachteter Fragestellungen ist die Anzahl der identifizierten Risiken gering. Zudem sind die identifizierten Risiken bei der derzeit vorhandenen Anzahl von im Feldversuch beteiligten Lang-Lkw und auch noch unter der Annahme von deutlich höheren Anteilen von Lang-Lkw am Güterverkehrsaufkommen als hinnehmbar oder zumindest beherrschbar einzustufen. Einzig für den Umstand der für Lang-Lkw in der Regel zu kurzen Schrägparkstände auf Rastanlagen müssten bei einer steigenden Anzahl an Lang-Lkw Lösungsansätze entwickelt werden, um das regelkonforme Abstellen der Lang-Lkw auch auf Rastanlagen weiterhin gewährleisten zu können. Zu beachten ist hinsichtlich der Gesamteinschätzung zudem, dass den erzielten Ergebnissen in der Regel die ganz spezifischen Randbedingungen des Feldversuchs zugrunde liegen. Teilweise resultieren diese Randbedingungen aus den Vorgaben der Ausnahme-Verordnung zum Feldversuch, in Einzelfällen auch aus dem unter Versuchsbedingungen angepassten Verhalten der Lang-Lkw-Fahrer. Sofern sich an diesen Randbedingungen Änderungen einstellen sollten oder die Unternehmen die heute geltenden Freiheitsgrade deutlicher ausnutzen, sind gewisse Fragestellungen neu zu beleuchten. Somit zeigt der Zwischenbericht in seinem Fazit zusammenfassend auf, dass an einzelnen Punkten weiter Forschungsbedarf besteht. Bis zum Ende des Feldversuchs wird die BASt diesen Fragen nachgehen und Nacherhebungen zur Validierung der bisherigen Ergebnisse durchführen können.
Zur Erhöhung des Verformungswiderstandes von Asphaltbefestigungen ist eine Vielzahl von Produkten entwickelt worden, welche dem Bitumen erst an der Mischanlage zugegeben werden können. Da deren Praxisverhalten aber oftmals noch nicht hinreichend bekannt ist, wurde auf einem Streckenabschnitt der BAB 1 bei Euskirchen eine Versuchsstrecke zur Erprobung der Additive eingerichtet. Fazit nach vier Jahren Nutzungsdauer ist, dass die untersuchten Produkte in Verbindung mit einem nicht-modifizierten Straßenbaubitumen grundsätzlich als vergleichbare Bindemittelalternative verwendbar sind. Die separate Zugabe an der Mischanlage hat jedoch i. a. einen höheren Aufwand zur Folge, so dass der Einsatz sich insbesondere für Sonderanwendungen (z. B. Kleinmengen oder Mischgut mit höherer Modifizierung) eignet. Für die Anwendungen wird eine objektbezogene, aussagekräftige erweiterte Eignungsprüfung als zwingend notwendig angesehen. Bei großflächigen Anwendungen sollte aufgrund der noch nicht eindeutig dokumentierten gleichmäßigen Verteilung der Produkte und des noch fehlenden quantitativen Nachweises den gebrauchsfertigen PmB der Vorzug gegeben werden. Außerdem wird darauf hingewiesen, dass die Erprobungsfelder zwar in einem Autobahnabschnitt der Bauklasse SV liegen, die Verkehrsbelastung aber noch deutlich unter den besonders hoch belasteten Autobahnabschnitten in Nordrhein-Westfalen liegt. Auf der Erprobungsstrecke ist somit die Gefahr einer vergleichsweise schnellen Spurrinnenbildung nicht besonders hoch.
Die vom Bundesministerium für Verkehr, Bau und Stadtentwicklung (BMVBS) beauftragte Studie zu den Auswirkungen neuartiger Lastzugkombinationen auf die Infrastruktur, den Verkehrsablauf und die Verkehrssicherheit liegt jetzt vor. Die Untersuchungen der Arbeitsgruppe der Bundesanstalt für Straßenwesen (BASt) konzentrieren sich ausschließlich auf die technischen Fragestellungen. Die wesentlichen Ergebnisse: - Eine erhöhte Straßenschädigung ist wegen der zugrunde gelegten neuen Fahrzeugtypen mit acht Achsen nicht zu erwarten. Infolge der prognostizierten allgemeinen Transportleistungssteigerung ist dieser Effekt jedoch von begrenzter Dauer. - Die Beanspruchung der Brücken wird durch 60-Tonnen-Lastzugkombinationen deutlich erhöht, was Ersatz oder Verstärkungen erforderlich machen wird. - Für die Tunnel der Bundesfernstraßen können sich wegen des deutlich größeren Ladevolumens höhere Brandlasten ergeben, mit der Folge erhöhter Anforderungen an die Sicherheitsausstattung. - Probleme bei der Befahrbarkeit von Kreisverkehren, Straßenkreuzungen und -einmündungen sowie Parkplätzen auf Rastanlagen werden sich infolge der größeren Fahrzeuglängen ergeben. Durch zusätzliche fahrzeugtechnische Einrichtungen - wie Lenkachse oder zusätzliche Gelenke - können diese gemindert werden. - Nach den vorliegenden Erfahrungen aus dem Ausland sind für ausreichend motorisierte und mit zuverlässigen Bremsanlagen ausgerüstete Transportfahrzeuge keine gravierenden Probleme hinsichtlich des Verkehrsablaufs und der Verkehrssicherheit auf Autobahnen zu erwarten. Im nachgeordneten Straßennetz (insbesondere Landes-, Kreis- und Gemeindestraßen) ist mit negativen Auswirkungen der Lastzugkombinationen sowohl auf die Verkehrssicherheit als auch auf die Leistungsfähigkeit der Straßen zu rechnen. So muss beispielsweise mit längeren Überholwegen und längeren Räumzeiten - etwa beim Abbiegen und an Bahnübergängen - gerechnet werden. - Die derzeitigen Schutz- und Rückhaltesysteme sind nicht für 60-Tonnen-Lastzugkombinationen ausgelegt. Derartige Rückhaltesysteme müssten erst entwickelt werden. Aufgrund der höheren Fahrzeuggewichte könnte die Unfallschwere bei Auffahrunfällen deutlich zunehmen. Moderne Fahrerassistenzsysteme (Spurhalteassistent sowie Bremsassistent mit Abstandsradar) könnten jedoch grundsätzlich dazu beitragen, sowohl Unfallrisiko als auch Unfallschwere zu verringern.
With the present brake signal pattern the traffic behind only receives the information that the brakes are applied, however, the drivers have no information about the intensity of the braking maneuver. In this report it is examined on the basis of a study of the literature, how the rear signal pattern could be optimized for a special representation of emergency braking maneuvers. In principle there are two suitable possibilities to reduce the driver reaction time: - An increase in the area and luminance of the brake lights intuitively provide the drivers following with an impression of approaching the vehicle in front , - Flashing lights are particularly suited to attract the attention of the driver following to the deceleration of the vehicle ahead , - The following advancement is recommended as an optimization of the rear signal pattern: When the brake assistant or ABS actuates or at a vehicle deceleration rate greater than 7 m/s-², the emergency braking maneuver is signaled by flashing of the third high-mounted brake light at a rate of 3-5 Hz. As an option, the area and luminance of the two lower brake lights could be increased in addition. These measures require changes to ECE Regulations No. 7 and No. 48 as well as to the Vienna Convention. The purpose of the described solution is to reduce the number or severity of rear-end accidents.