Sonstige
Refine
Document Type
- Conference Proceeding (256) (remove)
Language
- English (256) (remove)
Has Fulltext
- yes (256) (remove)
Keywords
- Conference (237)
- Konferenz (236)
- Accident (123)
- Unfall (123)
- Germany (118)
- Deutschland (117)
- Injury (85)
- Verletzung (84)
- Unfallrekonstruktion (72)
- Statistics (56)
Institute
Among European Countries, Spain first issued a Standard, UNE 135900:2005, further updated in 2008, that deals with homologation and effectiveness evaluation of road restraint systems components designed to reduce harm for bikers impacting on them. An in depth analysis and critical review of this standard is reported in this paper. Beside a close examination of the standard requirements, numerical models of the crash test stated by the standard have been set up and simulated to study the effects of slight speed and approach angle variations on test results, remaining within tolerance gaps allowed by the standard. Model were validated against experimental data. Together with the expected increasing severity of the impact according with speed, a strong influence of approach angle on injury parameters was found. Possible improvements to the norm, in order to make it more robust, are suggested.
Event Data Recorder (EDR) is an additional function installed in airbag control module (ACM) to record vehicle and occupant information for a brief period of time before, during, and after a crash event. EDRs are now being installed in ACMs by several automakers in the USA and in Japan. The aim of this study is to understand the performance of EDRs for the improvement of accident reconstruction with more reliable information. In the first report of the study, data obtained from EDRs of seven vehicle types were evaluated using 2006-2007 J-NCAP (Japanese new car assessment program) full-lap frontal barrier crash tests and offset frontal deformable barrier crash tests data. For more practical standpoint, we conducted thirteen crash tests reconstructing typical real-world accidents such as single vehicle accidents with barriers or poles, car to car accidents and multi rear-end collisions focusing on Japanese typical accident types. Data obtained from EDRs are compared with data obtained from optical speed sensor, instrumented accelerometers and high speed video cameras. The velocities determined from pre-crash data of EDRs and the maximum change in velocity, delta-V, and delta-V time history data obtained from post-crash data of EDRs are analyzed. The results are as follows: - Pre-crash velocities of EDRs were very accurate and reliable. An average difference between the EDR recording values and reference speeds was 4.2% and a root mean square of the differences was 9.2%. Only two cases resulted large differences for the pre-crash velocity. Both of them were cases with braking prior to the collision. However, another test with braking resulted less difference. The braking condition may influence accuracy of pre-crash velocities. - Maximum delta-Vs obtained from the EDRs showed uncertainty of measurement in several cases in comparisons with the reliable delta-V data. The differences in maximum delta-V were more than 10% in five of twenty-five events data and more than 20% in two of twenty-five events data. An average of the all differences was about 4% and root mean square of the differences was about 11%. Especially large deformation at narrow area may influence accuracy of post-crash delta-V. - Multiple rear-end crash tests were reconstructed using EDRs data as case studies. Some EDRs recorded two events and a time gap between two events, so that these reconstruction case studies were very accurate and reliable. - If though only one of three vehicles in multiple rear end crash was equipped EDR, overview and velocities of all cars may be reconstructed using these limited EDR data. In this case study, leading car- EDR data and middle car- EDR data were valuable. However if only following car was equipped EDR, the reconstruction was not accurate
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
Many safety-relevant tasks in control or diagnostics require binary choices such as "conflict versus separation" in air traffic control, "normal versus pathological" when interpreting x-ray pictures, or "permitted versus forbidden" when inspecting airport security scans. Deciders often are uncertain, but nevertheless required to decide between two alternatives, that is, they have not only to decide upon an action, but also about the admissible level of uncertainty. If the accepted level of judgment certainty is not taken into account, the sequence of decisions does not capture the full picture of the underlying decision process. Differences in judgment certainty are relevant, because they reflect not only the adequacy of the human-machine interface that is evaluated, but also the differences in expertise of the decider and the requirements of the actual situation or task. Therefore, capturing both judgment certainty and discrimination performance is essential. A comparison of different human-machine-interfaces (for air traffic control) is used to illustrate a methodological approach, which allows for integrated analyses of decision processes based on receiver-operator-characteristics and practical guidelines for the evaluation of human-machine-interfaces for safety-relevant operation procedures are provided.
This paper will outline ETSC's contribution to the European Union's road safety policy 2011-2020. It will present some of the main recommendations from ETSC's Blueprint for the 4th Road Safety Action Programme and will introduce the response to the European Commission's Road Safety Policy Orientations 2011-2020 (published July 2010). The second framework document presented is the Transport White Paper (published March 2011). The paper will focus on new targets and the new vision set for Europe's Road Safety policy picking out some issues in particular such as traffic law enforcement and the protection of vulnerable road users. It will argue that by reinforcing the current Road Safety Policy Orientations, the EU will be better placed to reach its new ambitious goal of halving road deaths by 2020 and the longer term zero casualty vision.
Estimation of the benefits for the UK for potential options to modify UNECE Regulation No. 95
(2010)
The side impact problem in Europe remains substantial. UK data shows that between 22% and 26% of car occupant casualties are involved in a side impact, but this rises to between 29% and 38% for those who are fatally injured. This indicates the more injurious nature of side impacts compared with frontal impacts. The European Enhanced Vehicle safety Committee (EEVC) has performed work to address the side impact issue since 1979. As part of its continuing work, it has recently investigated potential options for regulatory changes to improve side impact protection in cars further. To support this work the UK undertook an analysis to estimate the benefit for potential options to modify UNECE Regulation 95. The analysis used the UK national STATS19 and detailed Co-operative Crash Injury Study (CCIS) accident databases. Of the potential options reviewed, it was found that the addition of a pole test offered the greatest benefit.
Although the number of road accident casualties in Europe (EU27) is falling the problem still remains substantial. In 2011 there were still over 30,000 road accident fatalities. Approximately half of these were car occupants and about 60 percent of these occurred in frontal impacts. The next stage to improve a car's safety performance in frontal impacts is to improve its compatibility. The objective of the FIMCAR FP7 EU-project was to develop an assessment approach suitable for regulatory application to control a car's frontal impact and compatibility crash performance and perform an associated cost benefit analysis for its implementation. This paper reports the cost benefit analyses performed to estimate the effect of the following potential changes to the frontal impact regulation: • Option 1 " No change and allow current measures to propagate throughout the vehicle fleet. • Option 2 " Add a full width test to the current offset Deformable Barrier (ODB) test. • Option 3 " Add a full width test and replace the current ODB test with a Progressive Deformable Barrier (PDB) test. For the analyses national data were used from Great Britain (STATS 19) and from Germany (German Federal Statistical Office). In addition in-depth real word crash data were used from CCIS (Great Britain) and GIDAS (Germany). To estimate the benefit a generalised linear model, an injury reduction model and a matched pairs modelling approach were applied. The benefits were estimated to be: for Option 1 "No change" about 2.0%; for Option 2 "FW test" ranging from 5 to 12% and for Option 3 "FW and PDB tests" 9 to 14% of car occupant killed and seriously injured casualties.
Although the annual traffic accident statistics published by the national police is available in public, the detailed traffic accident data has not been released in Korea. Recently the Ministry of Land, Infrastructure and Transport recognized the importance of in-depth accident data to enhance road traffic safety and initiated a research project to establish a collection of the detailed accident data. The main objective of the project is a feasibility study to establish KIDAS (Korea In-Depth Accident Study). Within this project, three university hospitals which are located in mid-size cities have been selected to collect accident data. Annually, more than 500 cases of accidents have been collected from the in-patient's interviews and diagnosis. Unlike GIDAS (German In-Depth Accident Study), currently on-site investigation can"t be performed by the Korean police. The only available data is patient medical records, patient's description of accident circumstances and the damaged vehicle. Occasionally the police provide the accident investigation reports containing very brief information on accident causation and vehicle safety. In a first step, the concept of KIDAS is to adopt the format of iGLAD (Initiative for the Global Harmonization of Accident Data) for harmonization. Since the currently collected accident information is extremely limited compared with GIDAS, the other sources of data and calculations such as KNCAP vehicle data, pc-crash simulations, vehicle registration information, insurance company data are utilized to complete the iGLAD template. Results from KIDAS_iGLAD and the cases of assessment of active safety devices such as AEBS, ESC, and LDWS will be evaluated.
The need for improved EU level accident information and data was identified in the EU White Paper on Transport Policy (2001)1 and detailed in the Road Safety Action Plan (2003)2. The plan specifies that the EC will develop a road safety observatory to coordinate data collection within an integrated framework.
A change emerges in hospital landscape due to health political measures, which in consequence also influences the pre-clinical medical care of emergencies. The main focus of this study was to gather information about emergency medical care after traffic accidents on the basis of data of Bavarian emergency medical services. In Bavaria, in 2006 it was necessary to call an emergency doctor in the case of 14.261 traffic accidents. Predominantly the patients were provided by land-based life saving appliances, air rescue services were only applied in 19.1 % of the cases. 47.6 % of patients being involved in a traffic accident were transported into a primary health care hospital. A prehospital interval of more than 60 minutes was calculated in 20 % of emergency care. 96.2 % of the patients were transported to hospitals of tertiary or maximum supply by air rescue services. The life saving appliances" readiness for action is however restricted to daylight. A further limitation appeared for routine office hours in hospitals: Only 36.7 % of accidents occurred in this time frame. An increase of hospitalizations in clinics of maximum supply appeared from 2002 until 2006 while simultaneously the prehospital period was extended. To assure a sufficient medical care of seriously injured persons further on, a fulltime and area-wide expostulation of efficient facilities is necessary. For this purpose it is necessary to establish regional trauma networks as well as emergency medical service at night time. Beyond that, a cost efficient compensation of the structural, personnel and logistic expenses has to be assured.
Mechanical properties of tibial bone at compressive strain rates of 50-200 s-1 are obtained through Split Hopkinson pressure bar. Cylindrical specimens of 12-15 mm diameter and 2-5 mm thickness were used. The Young- moduli are calculated from linear portion of stress-strain curves. For both cortical and cancellous part of the bones, the Young- modulus was found to increase with the increasing strain rates. Also for both cancellous and cortical bones the Young- modulus increases consistently with increase in densities.
Twenty-eight percent of traffic accidents in Japan are rear-end collisions, and of these, 13% are multiple collisions (three or more vehicles and/or roadside objects). A post-crash braking system enables the driver to stop the vehicle in a short distance after a rear-end collision to prevent secondary collisions. In this study, the effectiveness of a post-crash braking system was examined using a drive recorder database. In 64% of rear-end collisions, the driver's braking was interrupted after the collision. The stopping distance was estimated with time data from the drive recorder. We predict that the brake assist would be effective in preventing secondary collisions in 21% of cases.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
Driver distraction
(2017)
This report for the Institute of Advanced Motorists (IAM) summarises recent research and knowledge from scientific studies about distracted driving. The report defines what it means to be "distracted" when driving, discusses the impact of distraction on driver behaviour and safety, and what can be done to reduce distracted driving. The focus of distraction discussed here relates to how drivers engage with technology when driving. The report begins with a background to driver distraction, followed by discussion about what is actually meant by driver distraction. It is then considered why humans cannot successfully do two things at the same time, particularly within the context of driving. The subsequent section summarises the scientific research findings to date with regard to driver distraction and technology, and how this affects different types of road user. Recommendations for how driver distraction can be mitigated in the real world and a summary conclude the report. Responses to common questions raised by drivers are presented in Appendix A.
Do learner gain sufficient braking capabilities at the end of education for collision avoidance?
(2013)
The paper describes a test design to evaluate the braking behaviour in the course of the driver education. The results show that the braking capabilities increased during the driver education and the learning effects are the same for males and females. The evaluation limit is set to 6 m/s-². At the beginning of education, 50% of the drivers do not reach this limit, although the driver education car is equipped with an emergency brake assist, which is regularly installed in all vehicles since 2009. After the education, 100% of the drivers can reach the limit. The results are mapped to a collision avoidance scenario.
The study aimed at estimating the impact of pedelecs (with an assumed higher speed than bicycles) on the traffic accident severity in Germany for different penetration rates. The analysis shows that in many real situations (68%) an electrical support of bicycles has no influence on the sequence of accident events. Taking into account a number of unreported "single bicycle accidents", the adoption of similar traffic behavior and similar age distribution, the authors determined a shift of 400 former slightly to seriously injured cyclists in Germany per year. Overall this would be an increase of approximately 2.3% in case of 10% of pedelec penetration with the pessimistic assumption of 10 km/h speed increase although first natural driving studies predict a much lower average speed increase of pedelecs. The hypothesis verbalized in the initial question whether a higher distribution of pedelecs will result in more severe accidents in Germany is not verified. The study shows that electrical support didn"t result in higher collision speed in general. In many accident situations, the speed of pedelecs has only a minor influence on the accident severity. Further research focusing on a possible change of driver behavior especially in new target groups (elderly people) will be needed.
The SafetyNet project was formulated in part to address the need for safety oriented European road accident data. One of the main tasks included within the project was the development of a methodology for better understanding of accident causation together with the development of an associated database involving data obtained from on-scene or "nearly onscene" accident investigations. Information from these investigations was complemented by data from follow-up interviews with crash participants to determine critical events and contributory factors to the accident occurrence. A method for classification of accident contributing factors, known as DREAM 3.0, was developed and tested in conjunction with the SafetyNet activities. Collection of data and case analysis for some 1 000 individual crashes have recently been completed and inserted into the database and therefore aggregation analyses of the data are now being undertaken. This paper describes the methodology development, an overview of the database and the initial aggregation analyses.
The Decision Support System (DSS) is one of the key objectives of the European co-funded research project SafetyCube in order to better support evidence-based policy making. Results will be assembled in the form of a DSS that will present for each suggested road safety measure: details of risk factor tackled, measure, best estimate of casualty reduction effectiveness, cost-benefit evaluation and analytic background. The development of the DSS presents a great potential to further support decision making at local, regional, national and international level, aiming to fill in the current gap of comparable measures effectiveness evaluation. In order to provide policy-makers and industry with comprehensive and well-structured information about measures, it is essential that a systems approach is used to ensure the links between risk factors and all relevant safety measures are made fully visible. The DSS is intended to become a major source of information for industry, policy-makers and the wider road safety community.
The Powered Two Wheelers (PTWs) accidents constitute one of the road safety targets in Europe. PTWs users' fatalities represent 15% of EU road fatalities, having increased the last few years, which is quite opposite than other road users casualties. To reduce PTW accidents is necessary to know which the accident causations are from different points of view (human factor, vehicle characteristics, environment, type of accident, situation, etc.). In TRACE project ("Traffic Accident Causation in Europe", under the European Commission 6th Framework Program, 2006-2008,) a specific task was focused on PTW users point of view, analyzing extensive databases to locate the main accident configurations (type of accident, severity, frequency), and an in-depth database to obtain the causation factors, the risk factors for each configuration founded in the extensive databases analysis and the variables associated to each causation factor in the PTW configurations.
Detailed investigations and reconstructions of real accidents involving vulnerable road users
(2005)
The aim of this research is to improve knowledge about vulnerable road users accidents and more specifically pedestrians or cyclists. This work has been based on a complete analysis of real accidents. From accidents chosen from an in-depth multidisciplinary investigation (psychology, technical, medical), we have tried to identify the configuration of the impact: car speed, pedestrian or cyclist orientations. Then, we have made a numerical modelling of the same configuration with a multibody software. In particular, we have reproduced the anthropometry of the victim and the front shape of the car. A first simulation has been performed on this starting configuration. Next, effects of some parameters such as car velocity or victim position at impact have been numerically studied in order to find the best correlations with all indications produced by the in-depth analysis. Finally, the retained configuration was close to the presumed real accident conditions because it reproduces in particular the same impact points on the car, the same injuries, and is according to the driver statement. This double approach associating an in-depth accident analysis and a numerical simulation has been applied on pedestrian-to-car and bicyclist-tocar accidents. It has allowed us to better understand the real kinematics of such impacts. Even if this method is based on a case to case study, it underlines which parameters are relevant on a vulnerable road user accident investigation and reconstruction.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
Within the COST Action TU1101 the working group WG 1 is dealing with acceptance criteria and problems in helmet use while bicycling concerning conspicuity, thermal stress, ventilation deficits and other potential confounding. To analyze the helmet usage practice of bicyclists in Europe a questionnaire was developed in the scope of working group 1 to collect relevant information by means of a field study. The questionnaire consists of some 66 questions covering the fields of personal data of the cyclist, riding und helmet usage habits, information concerning the helmet model and the sensation of the helmet, as well as information on previous bicycle accidents. A second complementary study is conducted to analyze if the use of a bicycle helmet influences the seating geometry and the posture of cyclists when riding a bicycle and if the if the helmet vertically limits the vision. For this purpose cyclists with and without helmets were photographed in real world situations and relevant geometrical values such as the decline of the torso, the head posture of the upper vertical vision limit due to the helmet were established from the photos. The interim results of the field studies which were conducted in Germany by the Hannover Medical School are presented in this study. Some 227 questionnaires were filled out, of which 67 participants had used a helmet and 42 of the 227 participants have had a bicycle accident before. For the analysis of the riding position and posture of the cyclist over 40 pictures of riders with a helmet and over 240 pictures of riders without a helmet were measured concerning the seating geometry to describe the influence of using a bicycle helmet. Some results in summary: From the riders interviewed with the questionnaire only 11% of the city bike riders and 12% of the mountain bike riders always used the helmet, while 38% of the racing bike riders and 88% of the e-bike-riders always used the helmet. The helmet use seems not to change the sensation of safety of cycling compared to the use of a car. The arguments for not wearing a helmet are mostly stated to be the short distance of a trip, high temperatures or carelessness and waste of time. The reasons for using a helmet are stated to be the feeling of safety and being used to using a helmet. Being a role model for others was also stated to be a reason for helmet use. Concerning the sensation of the helmet 9% of the riders reported problems with the field of vision when using a helmet, 57% saw the problem of sweating too much, and 10% reported headaches or other unpleasant symptoms like pressure on the forehead when using the helmet. The analysis of the seating posture from the pictures taken of cyclists revealed that older cyclists generally have a riding position where the handle bar is higher than the seat (0-° to 10-° incline from seat to handlebar), while younger riders had a higher variance (between -10-° decline and 20-° incline). Further, elderly riders and riders with helmets seem to have a more upright position of the upper body when cycling. The vertical vision limit due to the helmet is determined by the front rim of the helmet (mostly the sun shade). Typical values here range from 0-° (horizontal line from the eye to the sun shade) to 75-° upwards, in which elderly riders tend to have a slightly higher vertical vision limit possibly due to the helmet being worn more towards the face.
Although the statistics show a decreasing rate of child injuries and fatalities in German road accidents more efforts can be made to protect children in cars e.g. by developing appropriate child restraint systems. An important part in of this work can be achieved with the help of crash tests using child dummies. However these crash tests cannot completely reflect the situation of real world crashes as factors like children moving out of the optimal position or children incorrectly fastened by their parents are difficult to predict. Therefore this study gives an overview over the current accident and injury situation of child occupants in cars in German road accidents.
The incidence of side impacts was investigated from GIDAS data. Both vehicle-fixed object and vehicle-vehicle collisions were analysed as these are enclosed within the consumer testing program. Vehicle-fixed object collisions were stratified according to ESC availability. Results indicated that vehicles equipped with ESC rarely have pure-lateral impacts. An increase in oblique collisions was seen for the vehicles with ESC whereby most vehicle were driving in left curves. The analysis of vehicle-vehicle collisions developed injury risk curves were developed at the AIS3+ injury severity for the vehicle-vehicle side impacts. Results suggested that greatest injury risk occurred when a Pre Euro NCAP vehicle was struck by a Post Euro-NCAP vehicle. The remaining curves did not show different behaviour, indicating that stiffness increased have been equally combated. This was attributable to the few Post Euro-NCAP vehicles that had a deployed curtain airbag available in the sample. The integration of Euro NCAP testing has shown to improve vehicle crashworthiness for pole collisions, as those vehicles with ESC rarely incur lateral impacts.
The price of a new car increased almost every year for a long period. In recent years however, the budget available to most people for purchasing a car either did not grow or became even smaller. Therefore it was in the interest of some OEMs to offer economical car models in the so-called "8,000- Euro class". Here an important question arose regarding the safety of these vehicles. There is no question that the very high safety level of cars reached in Europe during the last decades should not be sacrificed as a consequence of smaller budgets. Customers with sense of responsibility have the right to be properly informed about the balance between safety and price so that they can make a deliberate decision when buying either a new or a used car. Against this background, the German magazine "AutoBILD" commissioned DEKRA to conduct fullscale frontal crash tests with a view to publishing the results. These tests have been carried out in accordance with the corresponding Euro NCAP crash test requirements and performance criteria. The tested vehicles were two new Logans produced by the manufacturer Dacia, two used cars of the type VW Golf IV (registration date 2000) and one new VW Fox. This paper describes the safety features of the vehicles and the results of the five crash tests to demonstrate state-of-the-art safety levels and what levels may be expected from vehicles in the "8,000- Euro class". Looking at real-world crashes it is of interest to think about future trends in a more detailed manner. Therefore it will be more and more necessary to supplement the federal statistics with more detailed in-depth information about the consequences of accidents and the safety performance of crashed vehicles.
The utilisation of secondary-safety systems to protect occupants has attained a very high level over the past decades. Further improvements are still possible, but increasingly minor progress is only to be had with a high degree of effort. Thus, a key aspect must be the impact to overall safety in an accident. If reliable information is available on an imminent crash, measures already taken in the pre-crash phase can result in a significantly great influence on the outcomes of the crash. With this background preventive measures are the key to a sustainable further reduction of the figures of crash victims on our roads. This paper aims to show a preventive approach that can contribute to lessening the consequences of a crash by creating an optimum interaction of measures in the fields of primary and secondary safety. To further enhance vehicle safety, driver assistant systems are already available that warn the driver of an imminent front-to-rear-end crash. The next step is to support him in his reactions or if he fails to react sufficiently, to even initiate an automatic braking when the crash becomes unavoidable. Automatic pre-crash braking can, in an ideal situation, fully prevent a crash or can significantly reduce the impact speed and thus the impact energy (and the severity of the accident). If a vehicle is being braked in the pre-crash phase, the occupants are already being pre-stressed by the deceleration. The information available about the imminent crash can be used to activate the belt tensioners and likewise other secondary safety systems in the vehicle right before the impact. The pre-crash deceleration also causes the front of the vehicle to dip. Conventional crash tests do not take this specific impact situation into consideration. This is why, for example, the influences of the pre-crash displacements of the occupants are not recorded in the test results. Furthermore, a reproducible representation of the benefit of the vehicle safety systems which prepare the occupants for the imminent impact is not possible. In order to demonstrate the functions of automated pre-crash braking and to investigate the differences during the impact as a consequence of the altered occupant positions as well as the initiation of force and deformations of the vehicle front, DEKRA teamed up with BMW to carry out a joint crash test with the latest BMW 5 series vehicle. It involved the vehicle braking automatically from a starting test speed of 64 km/h (corresponding to the impact speed set by Euro NCAP) down to 40 km/h. The test was still run by the intelligent drive system of the crash test facility. This required several modifications to be made to the test facility as well as to the vehicle. The paper will describe and discuss some relevant results of the crash test. In addition, the possible benefits of such systems will also be considered. The test supplemented the work of the vFSS working group (vFSS stands advanced Forward-looking Safety Systems).
Crash involvement studies using routine accident and exposure data : a case for case-control designs
(2009)
Fortunately, accident involvement is a rare event: the chance of an individual road user trip to end up in a crash is close to zero. Thus, according to general epidemiological principles one can expect the case-control study design to be especially suitable for quantifying the relative risk (odds ratio) of accident involvement of road users with a certain risk factor as compared to road users that do not have this characteristic. Ideally, of course, the database for such a case-control study should be established by drawing two independent random samples of cases (accidental units) and controls (nonaccidental units), respectively. If, however, special data collection is not an option, it is nevertheless possible to analyze routine accident and exposure data under a case-control design in order to fully exploit the information contained in already existing databases. As a prerequisite, accident and exposure data from different sources are to be combined in a single file of micro or grouped data in a way consistent with the case-control study design. Among other things, the proposed methodological approach offers the possibility to use in-depth data of the GIDAS type also in investigations of active vehicle safety by combining this data with appropriate vehicle trip data collected in mobility surveys.
Active safety systems are aimed at accident prevention, hence the knowledge required for their development is different from that required for passive safety systems aimed at injury prevention. Particularly, knowledge about accident causation is required. When looking at existing accident causation data, it is argued it fails to explain in sufficient detail how and why the accidents occur. Therefore, there is a need for detailed micro-level descriptions of accident causation mechanisms, and also of methodologies suitable for creating such descriptions. One study addressing these needs is the Swedish project FICA (Factors Influencing the Causation of Accidents and Incidents), where an accident investigation methodology suitable for active safety is developed, and in-depth accident investigations following this methodology are carried out on-scene in the area of Gothenburg by a multidisciplinary team. A preliminary aggregated analysis of different cases shows that the methodology developed is adequate for pointing out common contributing factors and devising principal countermeasures.
The current paper reports on the results of a pilot study aiming to investigate the effect of mobile telephone use on the driving performance of 5 amateur and 5 professional drivers. Their driving acuity was tested through a driving simulator. Analysis and interpretation of the results occurred comparing the drivers' driving performance while talking, reading messages and writing a message on the mobile phone (intervention time) with the drivers' driving performance engaged in no activity (control time). The variables affected by the mobile phone were the "steering", the "lane offset" and the "duration of lane offset". Moreover, the drivers involved in a car crash in the last five years appeared to differ from those who were not involved in a crash in both "lane offset" and "following distance". The results of this pilot study will inform the design of a large experimental study on 50 professional and 50 amateur drivers.
The fact that ADAC Air Rescue handles approximately 4,000 road accident missions every year gave rise to set up an accident research programme for which ADAC Air Rescue provides its data. This data is of initial informational quality and will be supplemented by data from the police, experts, fire brigades as well as hospitals and forensic institutes. Although the number of cases is still rather low, certain tendencies can be identified. The causes for most accidents occur when joining or intersecting traffic, followed by speeding in road bends and tailgating. Many accidents involve HGV rear end collisions, often causing serious injuries, considerable damage and technical problems for the rescue operations. With regard to the various impact types, it has become obvious that most of the extremely serious injuries are inflicted during a passenger car side impact. In addition, access to and removal of trapped passengers is becoming more and more complicated, partly due to the increasing use of high-strength materials, and rescue operations tend to be more time consuming.
Because of actual developments and the continuous increase in the field of drive assistant systems, representative and detailed investigations of accident databases are necessary. This lecture describes the possibility to estimate the potential of primary and secondary safety measures by means of a computerized case by case analysis. Single primary or secondary safety measures as well as a combination of both are presented. The method is exemplarily shown for the primary safety measure "Brake Assist" in pedestrian accidents. Regarding accident prevention only the primary safety measure is determined.
Accidents involving two wheels vehicles represent one of the more important types of accidents in Europe. These accidents are usually not easy to reconstruct specially for the analysis of the injuries and its correlation with accident dynamics and evidences. Different methodologies are applied in this work for the reconstruction of two wheeler accidents, especially accident involving motorcycles. From the typologies of road evidences like skid marks, to the use of Pc-Crash and the use of Madymo models, different reconstruction of real accidents are presented. One of the questions that sometimes arise for legal purposes when some type of head injuries arise is if the occupant was wearing or not a helmet. The correlation of head injuries with the use of the helmet is a very important issue, therefore an important legal aspect. One of the key questions for the reconstructions that is difficult to analyze, is if the vehicle occupant, was or not, wearing the helmet. Based on the previously collected information, a generic model of a helmet was developed on CAD 3D, followed by its conversion into finite elements, all in order to perform impact tests using the Madymo software that would help improve the helmet- safety, but that also can be used as a tool in accident reconstruction.
In recent years the boundaries between active and passive safety blurred more and more. Passive safety in the traditional term includes all safety aspects to prevent occupants to be injured or at least injury severity should be reduced. Passive Safety starts with the collision (first vehicle contact) and ends with rescue (open vehicle doors). Within this phase the occupant has to be protected by the passenger compartment whereby no intrusion should occur. Active safety on the other side was developed to interact prior to the collision whereby the goal is to prevent accidents. The extensive interaction between active and passive safety led to the terminologies "Primary" and "Secondary" safety whereas the expression Integrated Safety Concept was generated. Within this study the most well documented single vehicle accidents with cars not equipped with ESP were identified from the PENDANT database and reconstructed. Additional cases were found in the database ZEDATU of TU Graz. In comparison each case was simulated with the assumption that the cars were equipped with ESP. The differences regarding accident avoidance or crash severity as well as reduction of injury risk were analysed.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
In this study, we compared the injury severity of occupants according to the seating position and the crashing direction in motor vehicle accidents. In the driver's point of view, it was separated the seating position as "Near-side" and "Far-side". The study subjects were targeted by people who visited 4 regional emergency centers following motor vehicle accidents. Real-world investigation was performed by direct and indirect methods after patient- consent. The information of the damaged vehicle was informed by Collision Deformation Classification (CDC) code and the information of the injury of patients was informed by using the Abbreviated Injury Score (AIS) and Injury Severity Score (ISS). When the column 3 in CDC code was P, damaged at the middle part of lateral side, the average point of AIS 3 was 1.91-±1.72 in near-side and 1.02-±1.31 in far-side (p<0.01). The average point of maximum AIS (MAIS) was 2.78-±1.39 in near-side and 2.02-±1.11 in far-side (p<0.01). The average point of ISS was 15.74-±14.71 in near-side and 8.11-±8.39 in far-side (p<0.01). Also, when the column 3 in CDC code was D, damaged at the whole part of lateral side, it was significant that the average point of AIS 3 and MAIS in near-side was bigger than in far-side (p=0.02).
The aim of this study is to investigate the differences in car occupant injury severity recorded in AIS 2005 compared to AIS 1990 and to outline the likely effects on future data analysis findings. Occupant injury data in the UK Cooperative Crash Injury Study Database (CCIS) were coded for the period February 2006 to November 2007 using both AIS 1990 and AIS 2005. Data for 1,994 occupants with over 6000 coded injuries were reviewed at the AIS and MAIS level of severities and body regions to determine changes between the two coding methodologies. Overall there was an apparent general trend for fewer injuries to be coded at the AIS 4+ severity and more injuries to be coded at the AIS 2 severity. When these injury trends were reviewed in more detail it was found that the body regions which contributed the most to these changes in severity were the head, thorax and extremities. This is one of the first studies to examine the implications for large databases when changing to an updated method for coding injuries.
This study aimed at comparing head Wrap Around Distance (WAD) of Vulnerable Road User (VRU) obtained from the German in-depth Accident Database (GIDAS), the China in-depth Accident Database (CIDAS) and the Japanese in-depth Accident Database (ITARDA micro). Cumulative distribution of WAD of pedestrian and cyclist were obtained for each database (AIS2+) showing that WAD of cyclists were larger than the ones of pedestrians. Comparing three regions, the 50%tile WAD of GIDAS was larger than that of both Asian accident databases. Using linear regression that might predict WAD of pedestrians and cyclists from Impact speed and VRU height, WADs were calculated to be 206cm/219cm (Pedestrian/Cyclist) for GIDAS, 170cm/192cm for CIDAS and 211cm/235cm for ITARDA. In addition, this study may be helpful for reconsideration of WAD measurement alignment between accident reconstruction and test procedures.
Cycle helmets have continued to increase in popularity since their introduction half a century ago. Many studies indicate that overall, head injury can be significantly reduced by wearing them. This study was conducted using two distinct sets of real-world cycling collision data from Ireland, namely cases involving police collision reports and cases involving admission to a hospital emergency department. The analyses sought to simulate and analyse the protective performance of cycle helmets in such collision scenarios, by comparing the Head Injury Criterion score and peak head accelerations, both linear and angular. Cycle collisions were simulated using the specialised commercial software MADYMO. From the simulation results, these key metrics were compared between the same-scenario helmeted and unhelmeted cyclist models. Results showed that the inclusion of bicycle helmets reduced linear accelerations very significantly, but also increased angular accelerations significantly compared to unhelmeted situations. Given the modest protective performance of cycle helmets against angular accelerations, it is recommended that cycle helmet manufacturers and international test standards need to pay more attention to head angular accelerations.
One goal of the assessment of the crashworthiness of passenger cars is to characterize the potential of injury outcome to occupants of cars involved in an accident. This can be achieved by the help of an index that puts the number of injured occupants of passenger cars in relation to the number of cars involved in an accident. As a consequence, this index decreases with a lower potential of injury and rises with a higher number of injuries while assuming a fixed number of accidents. Another index is introduced that uses an economical weighting of each injury level. The consequential injury costs are calculated using the average economical costs for lightly, severely and fatally injured persons. The calculation of the safety indices is based on an anonymized sample of accident data provided by the Federal Statistical Office. An index of Mercedes passenger car drivers depending on the year of registration between 1991 and 2006 is compared to the index of drivers of cars of other makes within the same range of registration years.
This paper uses the national accident statistics of Great Britain to evaluate the effectiveness of Electronic Stability Control Systems (ESC) to reduce crash involvement rates. The crash experience of 8,951 cars is analysed and compared to a closely matching set of non-ESC cars using case-control methods. This is one of the largest ESC samples analysed to date. Overall the cars with ESC are involved in 3% fewer crashes although the effectiveness is substantially higher under conditions of adverse road friction. ESC equipped cars are involved in 15% fewer fatal crashes although this reduction represents the combined effect of ESC and passive safety improvements.
The average CO2 concentrations relevant to a motorcyclist wearing an integral helmet were measured twenty years ago and found to be alarmingly high. The present study examined gas concentrations typically inhaled by a motorcyclist. Average concentrations of CO2 for persons (n=4) wearing integral motorcycle helmets were measured in the laboratory and the field to facilitate comparison to previous work, and similarly high average concentrations were found: above 2% when stationary, well below 1% for speeds of 50km/h or more. Detailed measurements of the time-dependent CO2 concentrations during normal inhalation showed levels of about half of the corresponding average concentrations, including 1% at standstill, though higher concentrations (4% or more) are inhaled at the beginning of each breath. Opening the visor at standstill lowered the average inhaled concentration only to about 0.8%. The oxygen deficiency is equal to the CO2 concentration, and could also contribute negatively to motorcyclist cognitive abilities.
The national accident statistics demonstrate that the situation of passenger car side impacts is dominated by car to car accidents. Car side to pole impacts are relatively infrequent events. However the importance of car side to pole impacts is significantly increasing with fatal and seriously injured occupants. For the present study the German in-depth database GIDAS (German In-Depth-Accident Study) and the UK based database CCIS (Co-operative Crash Injury Study) were used. Two approaches were undertaken to better understand the scenario of car to pole impacts. The first part is a statistical analysis of passenger car side to pole impacts to describe the characteristics and their importance relevant to other types of impact and to get further knowledge about the main factors influencing the accident outcome. The second part contains a case by case review on passenger cars first registered 1998 onwards to further investigate this type of impact including regression analysis to assess the relationship between injury severity and pole impact relevant factors.
Event data recorders (EDRs) are a valuable tool for in-depth investigation of traffic accidents. EDRs are installed on the airbag control module (ACM) to record vehicle and occupant information before, during, and after a crash event. This study evaluates EDR characteristics and aims at better understanding EDR performance for the improvement of accident reconstruction with more reliable and accurate information regarding accidents. The analysis is based on six crash tests with corresponding EDR datasets.
Introduction: The incidence of trauma-related cervical-spine fractures is 19-88 / 100.000. In contrast, the incidence of cervical spine injuries is as high as 19% - 51% of all spinal trauma. Cervical spine injuries in non-polytrauma patients are rare. However, due to the potential damage to the spinal cord these traumata are feared and mustn't be missed. Cervical spine injuries represent the highest reported early mortality rate of all spinal trauma. The rate of functional impairment afterwards is high and the rate of reintegration into work is low compared to other organ systems. In the past, trauma surgeons often did x-rays of the cervical spine with low inhibition threshold and often without strong clinical suggestion for vertebral or discoligamental injuries. This practice was queried by the Canadian C-Spine rule and extensively discussed in the past. Therefore we did a retrospective study whether non-polytrauma patients benefit from cervical spine x-rays.
Causation patterns and data collection blind spots for fatal intersection accidents in Norway
(2010)
Norwegian fatal intersection accidents from the years 2005-2007 were analysed to identify any causation patterns among their underlying contributing factors, and also to evaluate whether the data collection and documentation procedures used by the Norwegian in-depth investigation teams produces the information necessary to perform causation pattern analysis. A total of 28 fatal accidents were analysed. Details on crash contributing factors for each driver in each crash were first coded using the Driving Reliability and Error Analysis Method (DREAM), and then aggregated based on whether the driver was going straight or turning. Analysis results indicate that turning drivers to a large extent are faced with perception difficulties and unexpected behaviour from the primary conflict vehicle, while at the same time trying to negotiate a demanding traffic situation. Drivers going straight on the other hand have less perception difficulties. Instead, their main problem is that they largely expect turning drivers to yield. When this assumption is violated, they are either slow to react or do not react at all. Contributing factors often pointed to in literature, e.g. high speed, drugs and/or alcohol and inadequate driver training, played a role in 12 of 28 accidents. While this confirms their prevalence, it also indicates that most drivers end up in these situations due to combinations of less auspicious contributing factors. In terms of data collection and documentation, information on blunt end factors (those more distant in time/space, yet important for the development of events) was more limited than information on sharp end factors (those close in time/space to the crash). A possible explanation is that analysts may view some blunt end factors as event circumstances rather than contributing factors in themselves, and therefore do not report them. There was also an asymmetry in terms of reported obstructions to view due to signposts and vegetation. While frequently reported as contributing for turning drivers, they were rarely reported as contributing for their counterparts in the same accidents. This probably reflects an involuntary focus of the analyst on identifying contributing factors for the driver legally held liable, while less attention is paid to the driver judged not at fault. Since who to blame often is irrelevant from a countermeasure development point of view, this underlying investigator mindset needs addressing to avoid future bias in crash investigation reports.
Causation of traffic accidents with children from the perspective of all involved participants
(2017)
In the year 2014 about 2,800 children between zero and 14 years got injured due to traffic accidents in Austria. More than 50% were taking part in traffic as active road users like cyclists or pedestrians. Within this study 46 real world traffic accidents between vehicles and children as pedestrians were analysed. In 39 cases, car drivers hit the crossing children. In the other cases, the collision opponents were busses, trucks or motorcycles. Most of the children got hit while crossing a road at urban sites. By analysing the traffic accidents from the perspectives of all involved participants, vehicle drivers and injured children, it is possible to identify factors for each participant, which led to the accident and factors that contributed the accident. The main task is to find patterns in the behaviour of crash victims (children and driver) before the collision. One important fact is that in more than 50% of the analysed cases sight obstructions were an important contributing factor for both, the driver and the child. From drivers view situations in which the child moved unexpected into the driven road lane were often found. For the injured child, factors like: no attention to the road traffic or no sufficient traffic observation were found to be relevant. Further it- possible to sensitise children and adults to possible source of critical traffic situations according to the findings of this study.
The GIDAS-investigation team of Dresden (VUFO) has documented more than 11.500 accidents since 1999. The documentation of the accident includes beside vehicle-, injury- and environmental-data very detailed reconstruction data. Within this accident investigation the VUFO began to record the skid resistance of the accident site in 2009. The measurements are divided in macro- and microroughness (Sand depth method and Portable Skid Resistance Tester-SRT-by Munro-Stanley London-©). Both methods are used to determine the skid resistance for more than 1000 passenger cars. The aim of the present study is to find out a relationship between the measured skid resistance, the road conditions and the friction coefficient, which is used to calculate the maximum accelerations and decelerations during a reconstruction of an accident. Basic approach to convert the SRT-value into the friction coefficient is the calculation of the theoretical absorbed energy of the spring rubber system of the swinging arm of lever. This absorbed energy is used to get the friction coefficient by using the equations for the work of friction. To consider the road-behavior, in correlation to the friction coefficient, the results will be merged with existing literature. Last step for this study will be a comparison between actual used friction coefficients all over the GIDAS-database and the theoretical results. The study shows, if it is possible to use the SRT-Measurement for the estimation of a friction coefficient for the reconstruction of a traffic accident. As expected, the GIDAS-Database and the additional measurement of the roughness of the road directly on the spot are an enormous useful dataset.
Ruptures and dissections of the thoracic and abdominal aortic vessel caused by traffic accidents are rare but potentially life-threatening injuries. They can occur by blunt trauma via seat belt or dashboard injury. The study aimed at evaluating the overall mortality, morbidity, neurological disorders, and differences in operative procedures of open repair and stenting. It shows that, with a change and improvement in diagnostic tools and surgical approach, mortality and morbidity of blunt aortic injuries were significantly reduced. Still an immediate life-threatening injury early diagnosis via multiple-slice and scans and surgical repair with minimally invasive stents showed excellent short-time results for selected patients.