Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (101)
- Buch (Monographie) (20)
- Wissenschaftlicher Artikel (4)
- Arbeitspapier (1)
Schlagworte
- Injury (126) (entfernen)
Institut
In most of developed countries, the progress made in passive safety during the last three decades allowed to drastically reduce the number of killed and severely injured especially for occupants of passenger cars. This reduction is mainly observed for frontal impacts for which the AIS3+ injuries has been reduced about 52% for drivers and 38% for front passengers. The stiffening of the cars' structure coupled with the generalization of airbags and the improvement of the seatbelt restraint (load limiter, pretension, etc.) allowed to protect vital body regions such as head, neck and thorax. However, the abdomen did not take advantage with so much success of this progress. The objective of this study is to draw up an inventory on the abdominal injuries of the belted car occupants involved in frontal impact, to present adapted counter-measures and to assess their potential effectiveness. In the first part the stakes corresponding to the abdominal injuries will be defined according to types of impact, seat location, occupants' age and type of injured organs. Then, we shall focus on the abdominal injury risk curves for adults involved in frontal impact and on the comparisons of the average risks according to the seat location. In the second part we will list counter-measures and we shall calculate their effectiveness. The method of case control will be used in order to estimate odds ratio, comparing two samples, given by occupants having or not having the studied safety system. For this study, two type of data sources are used: national road injured accident census and retrospective in-depth accident data collection. Abdominal injuries are mainly observed in frontal impact (52%). Fatal or severe abdominal occupant- injuries are observed at least in 27% of cases, ranking this body region as the most injured just after the thorax (51%). In spite of a twice lower occupation rate in the back seats compared to the front seats, the number of persons sustaining abdominal injuries at the rear place is higher than in the front place. In recent cars, the risk of having a serious or fatal abdominal injury in a frontal impact is 1.6% for the driver, 3.6% for the front passenger and 6.3% for the rear occupants. The most frequently hurt organs are the small intestine (17%), the spleen (16%) and the liver (13%). The most common countermeasures have a good efficiency in the reduction of the abdominal injuries for the adults: the stiffness of the structure of the seats allows decreasing the abdominal injury risk from 54% (driver) to 60% (front occupant), the seatbelt pretensioners decrease also this risk from 90% (driver) to 83% (front passenger).
Still correlated with high mortality rates in traffic accidents traumatic aortic ruptures were frequently detected in unprotected car occupants in the early years. This biomechanical analysis investigates the different kinds of injury mechanisms leading to traumatic aortic injuries in todays traffic accidents and how the way of traffic participation affects the frequency of those injuries over the years. Based on GIDAS reported traffic accidents from 1973 to 2014 are analyzed. Results show that traumatic aortic injuries are mainly observed in high-speed accidents with high body deceleration and direct load force to the chest. Mostly chest compression is responsible for the load direction to the cardiac vessels. The main observed load vector is from caudal-ventral and from ventral solely, but also force impact from left and right side and in roll-over events with chest compression lead to traumatic aortic injuries. Classically, the injury appeares at the junction between the well-fixed aortic arch and the pars decendens following a kind of a scoop mechanism, a few cases with a hyperflexion mechanism are also described. In our analysis the deceleration effect alone never led to an aortic rupture. Comparing the past 40 years aortic injuries shift from unprotected car occupants to today's unprotected vulnerable road users like pedestrians, cyclists and motorcyclists. Still the accident characteristics are linked with chest compression force under high speed impact, no seatbelt and direct body impact.
To elucidate the risk of pedestrians, bicycle and motorbike users, data of two accident research units from 1999 to 2014 were analysed in regard to demographic data, collision details, preclinical and clinical data using SPSS. 14.295 injured vulnerable road users were included. 92 out of 3610 pedestrians ("P", 2.5%), 90 out of 8307 bicyclists ("B", 1.1%) and 115 out of 4094 motorcycle users ("M", 2.8%) were diagnosed with spinal fractures. Thoracic fractures were most frequent ahead of lumbar and cervical fractures. Car collisions were most frequent mechanism (68, 62 and 36%). MAIS was 3.8, 2.8 and 3.2 for P, B and A with ISS 32, 16 and 23. AIS-head was 2.2, 1.3 and 1.5). Vulnerable road users are at significant risk for spine fractures. These are often associated with severe additional injuries, e.g. the head and a very high overall trauma severity (polytrauma).
While cyclists and pedestrians are known to be at significant risk for severe injuries when exposed to road traffic accidents (RTAs) involving trucks, little is known about RTA injury risk for truck drivers. The objective of this study is to analyze the injury severity in truck drivers following RTAs. Between 1999 and 2008 the Hannover Medical School Accident Research Unit prospectively documented 43,000 RTAs involving 582 trucks. Injury severity including the abbreviated injury scale (AIS) and the maximum abbreviated injury scale (MAIS) were analyzed. Technical parameters (e.g. delta-v, direction of impact), the location of accident, and its dependency on the road type were also taken into consideration. The results show that the safety of truck drivers is assured by their vehicles, the consequence being that the risk of becoming injured is likely to be low. However, the legs especially are at high risk for severe injuries during RTAs. This probability increases in the instance of a collision with another truck. Nevertheless, in RTAs involving trucks and regular passenger vehicles, the other party is in higher risk of injury.
In this study, we compared the injury severity of occupants according to the seating position and the crashing direction in motor vehicle accidents. In the driver's point of view, it was separated the seating position as "Near-side" and "Far-side". The study subjects were targeted by people who visited 4 regional emergency centers following motor vehicle accidents. Real-world investigation was performed by direct and indirect methods after patient- consent. The information of the damaged vehicle was informed by Collision Deformation Classification (CDC) code and the information of the injury of patients was informed by using the Abbreviated Injury Score (AIS) and Injury Severity Score (ISS). When the column 3 in CDC code was P, damaged at the middle part of lateral side, the average point of AIS 3 was 1.91-±1.72 in near-side and 1.02-±1.31 in far-side (p<0.01). The average point of maximum AIS (MAIS) was 2.78-±1.39 in near-side and 2.02-±1.11 in far-side (p<0.01). The average point of ISS was 15.74-±14.71 in near-side and 8.11-±8.39 in far-side (p<0.01). Also, when the column 3 in CDC code was D, damaged at the whole part of lateral side, it was significant that the average point of AIS 3 and MAIS in near-side was bigger than in far-side (p=0.02).
The incidence of side impacts was investigated from GIDAS data. Both vehicle-fixed object and vehicle-vehicle collisions were analysed as these are enclosed within the consumer testing program. Vehicle-fixed object collisions were stratified according to ESC availability. Results indicated that vehicles equipped with ESC rarely have pure-lateral impacts. An increase in oblique collisions was seen for the vehicles with ESC whereby most vehicle were driving in left curves. The analysis of vehicle-vehicle collisions developed injury risk curves were developed at the AIS3+ injury severity for the vehicle-vehicle side impacts. Results suggested that greatest injury risk occurred when a Pre Euro NCAP vehicle was struck by a Post Euro-NCAP vehicle. The remaining curves did not show different behaviour, indicating that stiffness increased have been equally combated. This was attributable to the few Post Euro-NCAP vehicles that had a deployed curtain airbag available in the sample. The integration of Euro NCAP testing has shown to improve vehicle crashworthiness for pole collisions, as those vehicles with ESC rarely incur lateral impacts.
Recently, EuroNCAP updated the upper legform test protocols. The main objective of this study is to establish the upper legform test in KIDAS (Korean In-depth Accident Study) taking into account domestic pedestrian accident data as well as anthropometric data to protect elderly pedestrians whose average height and weight is much smaller and lighter than other age groups, especially compared to Europeans. Therefore 230 cases of pedestrian accidents from KIDAS were investigated to explore the injury severity of body regions as well as age related injury patterns. Injuries of all body regions were examined, with a special focus on injuries of abdomen and pelvic area. On the other hand, in order to explore Korea's pedestrian accident environment, national police data and KIDAS (Korean In-depth Accident Study) data were compared. The results should be taken into account in future analyses and possible improvements, such as regulations and KNCAP test protocols, of the pedestrian safety policy in Korea.
Interdisciplinary accident research and research projects of AARU Audi Accident Research Unit
(2017)
AARU (Audi Accident Research Unit) is an interdisciplinary research project of the University Hospital Regensburg in cooperation with AUDI AG. Specific objective is to comprehend the respective accident scenario and retrieve generally applicable findings as to technical, medical and psychological processes. In order to prevent traffic accidents and to alleviate vehicle accident consequences, postulates of general traffic safety, human-machine interaction, technical design and function of new vehicles and occupant as well as third party protection shall be inferred from these findings. Specifically, each accident with new Audi, Lamborghini and Ducati vehicles involved is analyzed interdisciplinary, discussed in a case meeting and anonymously documented with more than 2,000 parameters. The database is continually used for solving safety relevant issues. Parallel to accident analysis, research projects are performed in the fields medicine, psychology and engineering in order to gain comprehensive insight and identify potential additional areas of activity of accident research.
Verkehrsunfallopfer, die beim Unfall überrollt werden, erleiden fast immer tödliche Verletzungen. Im innerstädtischen Bereich ereignen sich diese Unfälle mehrheitlich im niedrigen Geschwindigkeitsbereich. Die Frage der Vermeidbarkeit des Unfalls wird daher sehr oft seitens der Ermittlungsbehörde an die Sachverständigen gestellt. Im Rahmen der Unfallrekonstruktion spielt der Reifenprofilabdruck am Leichnam eine wichtige Rolle. Er belegt nicht nur den Überrollungsvorgang selbst, sondern erlaubt auch die Identifikation der Überrollungsrichtung und -region, aber auch des in Frage kommenden Reifens. Bei der retrospektiven Analyse von 120 Überrollungsfällen in Berlin (Fußgänger, Radfahrer und Kraftradfahrer) aus den letzten 23 Jahren wurde untersucht, wie verlässlich dieses Merkmal ist, wie oft und wo man es findet und von welchen Faktoren seine Entstehung beeinflusst wird.
Die Elektromobilität ist nicht erst seit dem Nationalen Entwicklungsplan Elektromobilität der Bundesregierung, der u.a. als Zielsetzung hat, dass eine Million Elektrofahrzeuge bis 2020 auf deutschen Straßen fahren sollen, ein allgegenwärtiges Thema. Eine zu lösende Aufgabe auf dem Weg zu diesem Ziel ist die Betrachtung der Abhängigkeiten der Systeme Elektrofahrzeug, Ladeverbindungseinheit und Ladesystem, welche bisher weitgehend autonom normiert sind. Um Personen- und Sachschäden beim Laden von Fahrzeugen zu vermeiden, ist es möglicherweise erforderlich, Anforderungen an die Sicherheit dieses Gesamtsystems zu definieren. Zu diesem Zweck beauftragte die Bundesanstalt für Straßenwesen die SGS-TÜV Saar GmbH, Competence Center Funktionale Sicherheit mit der Durchführung einer Risikoanalyse, mit dem Ziel die Sicherheitsaspekte beim Laden eines Elektrofahrzeuges zu untersuchen. Bisher nicht bzw. unzureichend betrachtete Gefährdungen während des Ladevorganges sollten aufgezeigt werden. Nötige Maßnahmen sollten definiert und punktuell mittels Tests validiert werden, um identifizierte Risiken auf ein ausreichend geringes Maß zu senken. Im Kern wurde untersucht, welche potenziellen Risiken (Das Risiko definiert sich als die Beschreibung eines Ereignisses mit der Möglichkeit negativer Auswirkungen. Das Risiko wird allgemein als Produkt aus Eintrittswahrscheinlichkeit eines Ereignisses und dessen Konsequenz angesehen. (Quelle: Wikipedia)) beim Laden eines Elektrofahrzeugs auftreten. Auf Basis einer Normenrecherche wurde die Frage beantwortet, an welchen Stellen normativer und gesetzlicher Handlungsbedarf besteht. Dazu wurden die nachfolgenden Schwerpunkte erarbeitet: - Darstellung möglicher sicherheitskritischer Bedingungen beim Laden; - Zuordnung der sicherheitskritischen Bedingungen zu den Subsystemen Infrastruktur, Kabel und Fahrzeug; - Definition von Maßnahmen zur Erhöhung der Sicherheit beim Laden; - Aufzeigen der Zuständigkeiten für die Gewährleistung der Sicherheit; - Offenlegung des regelungsseitigen Bedarfs. Im ersten Schritt wurde eine Risikoanalyse durchgeführt, um die potenziellen Risiken beim Laden eines Elektrofahrzeugs aufzuzeigen. Die Risikoanalyse wurde zunächst ohne Berücksichtigung bereits normativ oder gesetzlich festgelegter Schutzmaßnahmen durchgeführt. Anschließend erfolgte eine iterative Weiterführung der Betrachtung der Risiken in zweierlei Hinsicht: a) Berücksichtigung existierender normativer und/ oder gesetzlicher Anforderungen, welche parallel zur Risikoanalyse recherchiert wurden; b) Beschreibung ergänzender technischer und/ oder organisatorischer Maßnahmen, um nicht abgedeckte Risiken weiter zu reduzieren. Danach wurde eine erneute Beurteilung der Risiken vorgenommen, um aufzuzeigen, ob die vorhandenen bzw. neu definierten Maßnahmen in der Lage sind, das identifizierte Risiko in ausreichendem Maß zu reduzieren. Generell zeigte sich im Rahmen der Risikoanalyse eine breite, durch Normen und Richtlinien bzw. gesetzlichen Regelungen, vorhandene Abdeckung der möglichen Risiken. Derzeit nicht abgedeckte Risiken konnten adressiert und wirksame Lösungsmöglichkeiten vorgeschlagen werden. Bei Umsetzung aller aufgezeigten Lösungsansätze bleiben somit keine relevanten Risiken offen. Jedoch zeigt sich auch, dass zu bestimmten Themen dringender Handlungsbedarf besteht. Als Ergebnis ließ sich zu folgenden Punkten ein konkreter Handlungsbedarf ableiten: - Als eines der Hauptrisiken wurde das Laden an einer haushaltsüblichen Schukosteckdose, ohne die Nutzung einer zusätzlichen in der Ladeleitung integrierten Schutzeinrichtung, identifiziert. Bei Ladeleitungen mit Schutzeinrichtung hängt deren Schutzwirkung nicht zuletzt von einer regelmäßigen technischen Überprüfung ab; - Als relevant wurden weiterhin die elektromagnetischen Felder, die von einer Ladeleitung bei hohen Strömen ausgehen (zukünftige Schnellladesysteme), identifiziert, hier sind tiefergehende Untersuchungen erforderlich; Im Sinne der Risikominimierung sollte auch das maximal zulässige Gewicht der Ladegarnitur limitiert sein; - Auch Risiken, die sich durch die Bedienung ergeben, wurden untersucht. Mit entsprechenden Hinweisen im Bedienungshandbuch des Elektrofahrzeuges kann hier bereits einigen möglichen Gefahren begegnet werden. Dies betrifft unter anderem die Handhabung der Ladegarnitur beim Laden im öffentlichen Raum. Aus den ermittelten, noch umzusetzenden Maßnahmen geht hervor, dass der derzeitige Stand der Normung und gesetzlichen Regelungen noch nicht vollkommen ausreichend ist, um alle ermittelten und aufgezeigten Risiken in ausreichendem Maße zu reduzieren. Aus den Ergebnissen der Studie wird aber auch deutlich, dass die Sicherheit nicht alleine von einem Teilsystem alleine, sondern vielmehr durch das sichere Zusammenwirken aller Teile, auch in Kombination mit dem Verhalten der Nutzer und partizipierender Personen, gewährleistet wird.
Mit der flächendeckenden Einführung des Beifahrerairbags ergab sich das Problem der nachträglich festgestellten Inkompatibilität mit rückwärts gerichten Kindersitzen. Zahlreiche tödliche Unfälle mit Babyschalen, insbesondere in den USA, führten unter anderem dazu, dass in den Mitgliedsstaaten der Europäischen Union die Beförderung von Kindern in einem rückwärtsgerichteten Kinderschutzsystem auf einem mit Frontairbag geschützten Autositz untersagt wurde, sofern der Airbag nicht deaktiviert wurde. Heute gibt es eine Vielzahl an Möglichkeiten, die dem Nutzer zur Abschaltung des Airbags zur Verfügung stehen. Mit der Notwendigkeit der Abschaltung ergibt sich die Gefahr zweier Arten der Fehlbenutzung: die Beförderung eines Kindes in einer Babyschale trotz aktivierten Airbags beziehungsweise die Mitfahrt eines erwachsenen Insassen trotz deaktivierten Airbags. Im Rahmen dieser Studie wurden zu den beiden Fehlbenutzungsarten Beobachtungs- und Befragungsstudien durchgeführt, Unfalldaten in Hinblick auf die Problematik der Fehlbenutzung der Airbagabschaltung analysiert und Versuche zur erneuten Bewertung des Risikos, das durch heutige und zukünftige Airbagsysteme ausgeht, durchgeführt. In den Umfragen ließen sich nur schwer Daten zum Missbrauch bei der Beförderung von Kindern mit Airbag auf dem Beifahrersitz erfassen. Es kommt insgesamt zu nur wenigen Fällen des Transports eines Kindes auf dem Beifahrersitz mit aktivem Airbag, was zum einen an der hohen Abschaltquote des Beifahrerairbags liegt, zum anderen an der Präferenz der Eltern, die Kinder auf dem Rücksitz zu transportieren. Der Großteil dieser Fehlbenutzungsfälle entsteht in älteren Pkw, die einen Werkstattaufenthalt für die Deaktivierung/Aktivierung erfordern. Keine Missbräuche beziehungsweise technische Fehler fanden sich bei den Systemen mit automatischer Sitzerkennung. Der überwiegende Anteil der Missbrauchsfälle bei den Modellen mit manueller Umschaltmöglichkeit geht offenbar auf Vergessen zurück. Der Missbrauch zweiter Art wird ebenfalls wirkungsvoll durch automatische Systeme verhindert. Bei dieser Beförderungskonstellation ergibt sich jedoch praktisch immer ein Problem, wenn der Beifahrerairbag in einer Werkstatt deaktiviert wurde. Die dadurch für einen erwachsenen Mitfahrer entstehende Gefährdung wird als weniger gravierend eingeschätzt. Bei der manuellen Umschaltung im Fahrzeug verbleibt ebenfalls ein Vergessensproblem wie beim Missbrauch erster Art. Auch die Unfallanalyse deutet auf eine geringe Fehlbenutzungsquote hin. Von den untersuchten GIDAS-Frontalaufprallunfällen mit über 300 betroffenen Kindern nutzten lediglich 24 Kinder den Beifahrerplatz in einem Auto, das mit einem Beifahrerairbag ausgestattet war. In den meisten Fällen war der Airbag vorschriftsmäßig deaktiviert. In den nachgewiesenen Fehlbenutzungsfällen waren die Unfallfolgen für die betroffenen Babys gering. Die untersuchten Einzelfälle zeigen jedoch die tödliche Gefahr, die vom Beifahrerairbag ausgehen kann. Auf der technischen Seite gab es im Lauf der letzten Jahre grundsätzliche Veränderungen im Bereich der Gestaltung des Beifahrerairbags. Während bei der früheren Einbauposition des Airbags die Schale direkt angeschossen wurde, entfaltet sich dieser heutzutage eher nach oben, stützt sich an der Windschutzscheibe ab und kommt danach erst mit der Schale in Kontakt. Da er in diesem Zustand aber schon weitestgehend voll entfaltet ist, besitzt er zu diesem Zeitpunkt kaum noch die Aggressivität, die bei den Beifahrerairbags der ersten Generation beobachtet werden konnte, und stellt somit wahrscheinlich eine geringere Gefahr für das Kleinkind in der Babyschale dar. Damit lässt sich ein deutlicher Trend in Richtung weniger gefährlicher Airbags erkennen. Der Originalbericht enthält als Anhänge den Abdruck des Expertenfragebogen, die Zusammenfassung der Expertenbefragung, den Umdruck der Online-Befragung sowie den Fragebogen der Feldbefragung "Kindersitze und Airbag auf dem Beifahrersitz". Auf die Widergabe dieser Anhänge wurde in der vorliegenden Veröffentlichung verzichtet. Sie liegen bei der Bundesanstalt für Straßenwesen vor und sind dort einsehbar. Verweise auf die Anhänge im Berichtstext wurden zur Information des Lesers beibehalten.
Trauma management (TM) covers two types of medical treatment: the initial one provided by Emergency Medical Services (EMS) and a further one provided by permanent medical facilities. There is a consensus in the professional literature that to reduce the severity and the number of road crash victims, the TM system should provide rapid and adequate initial care of injury, combined with sufficient further treatment at a hospital or trauma centre. Recognizing the important role of TM for reducing road crash injury outcome, it was decided, within the EU funded SafetyNet project, to develop road safety performance indicators (SPIs) which would characterize the level of TM systems" performance in European countries and enable country comparisons. The concept of TM SPIs was developed based on a literature study of performance indicators in TM, a survey of available practices in Europe and data availability examinations. A set of TM SPIs was introduced including 14 indicators which characterize five issues such as: availability of EMS stations; availability and composition of EMS medical staff; availability and composition of EMS transportation units; characteristics of the EMS response time, and availability of trauma beds in permanent medical facilities. Basic information on the TM systems was collected in close cooperation with the national expert group. A dataset with TM SPIs for 21 countries was created. It was demonstrated that the countries can be compared using selected TM SPIs. Moreover, a more general comparison of the TM systems' performance in the countries is possible, using multiple ranking and statistical weighting techniques. By both methods, final estimates were received enabling the recognition of groups of countries with similar levels of the TM system's performance. The results of various trials were consistent as to the recognition of countries with high or low level of the TM systems" performance, where in grouping countries with intermediate levels of the TM system's performance some differences were observed. The SafetyNet project's practice demonstrated that data collection for estimating TM SPIs is not an easy task but is realizable for the majority of countries. The TM SPIs" message is currently limited to the availability of trauma care services. Further development of the TM SPIs should focus on characteristics of actual treatment supplied, based on combined police and medical road crash related databases.
To improve vehicle safety in frontal collisions, the crash compatibility between the colliding vehicles is crucial. Compatibility aims to improve both the self and partner protection properties of vehicles. Although compatibility has received worldwide attention for many years, no final assessment approach has been defined. Within the Frontal Impact and Compatibility Assessment Research (FIMCAR) project, different frontal impact test procedures (offset deformable barrier [ODB] test as currently used for Economic Commission for Europe [ECE] R94, progressive deformable barrier test as proposed by France for a new ECE regulation, moveable deformable barrier test as discussed worldwide, full-width rigid barrier test as used in Federal Motor Vehicle Safety Standard [FMVSS] 208, and full-width deformable barrier test) were analyzed regarding their potential for future frontal impact legislation. The research activities focused on car-to-car frontal impact accidents based on accident investigations involving newer cars. Test procedures were developed with both a crash test program and numerical simulations. The proposal from FIMCAR is to use a full-width test procedure with a deformable element and compatibility metrics in combination with the current offset test as a frontal impact assessment approach that also addresses compatibility. By adding a full-width test to the current ODB test it is possible to better address the issues of structural misalignment and injuries resulting from high acceleration accidents as observed in the current fleet. The estimated benefit ranges from a 5 to 12 percent reduction of fatalities and serious injuries resulting from frontal impact accidents. By using a deformable element in the full-width test, the test conditions are more representative of real-world situations with respect to acceleration pulse, restraint system triggering time, and deformation pattern of the front structure. The test results are therefore expected to better represent real-world performance of the tested car. Furthermore, the assessment of the structural alignment is more robust than in the rigid wall test.
Road accidents are typically analyzed to address influences of human, vehicle, and environmental (primarily infrastructure) factors. A new methodology, based on a "Venn diagram" analysis, gives a broader perspective on the probable factors, and combinations of factors, contributing both to the occurrence of a crash and to sustaining injuries in that crash. The methodology was applied to 214 accidents on the Mumbai-Pune expressway. Factors contributing to accidents and injuries were addressed. The major human factors influencing accidents on this roadway were speeding (30%) and falling asleep (29%), while injuries were primarily due to lack of seat belt use (46%). The leading infrastructure factor for injuries was impact with a roadside manmade structure (28%), and the main vehicle factor for injuries was passenger compartment intrusion (73%). This methodology can help identify effective vehicle and infrastructure-related solutions for preventing accidents and mitigating injuries in India.
Injury severity of e.g. pedestrians or bikers after crashes with cars that are reversing is almost unknown. However, crash victims of these injuries can frequently be seen in emergency departments and account for a large amount of patients every year. The objective of this study is to analyze injury severity of patients that were crashed into by reversing cars. The Hannover Medical School local accident research unit prospectively documented 43,000 road traffic accidents including 234 crashes involving reversing cars. Injury severity including the abbreviated injury scale (AIS) and the maximum abbreviated injury scale (MAIS) was analyzed as well as the location of the accident. As a result 234 accidents were included into this study. Pedestrians were injured in 141 crashes followed by 70 accidents involving bikers. The mean age of all crash victims was 57 -± 23 years. Most injuries took place on straight stretches (n = 81) as well as parking areas (n = 59), entries (n = 36) or crossroads (n = 24). The AIS of the lower extremities was highest followed by the upper extremities. The AIS of the neck was lowest. The mean MAIS was 1.3 -± 0.6. The paper concludes that the lower extremities show the highest risk to become injured during accidents with reversing cars. However, the risk of severe injuries is likely low.
Ruptures and dissections of the thoracic and abdominal aortic vessel caused by traffic accidents are rare but potentially life-threatening injuries. They can occur by blunt trauma via seat belt or dashboard injury. The study aimed at evaluating the overall mortality, morbidity, neurological disorders, and differences in operative procedures of open repair and stenting. It shows that, with a change and improvement in diagnostic tools and surgical approach, mortality and morbidity of blunt aortic injuries were significantly reduced. Still an immediate life-threatening injury early diagnosis via multiple-slice and scans and surgical repair with minimally invasive stents showed excellent short-time results for selected patients.
In North America, frontal crash tests in both the regulatory environment and consumer-based safety rating schemes have historically been based on full-width and moderate-overlap (40%) vehicle to barrier impacts. The combination of improved seat-belt technologies, notably belt tensioning and load limiting systems, together with advanced airbags, has proven very effective in providing occupant protection in these crash modes. Recently, however, concern has been raised over the contribution of narrower frontal impacts, involving primarily the vehicle corners, to the incidence of fatality and serious injury as a result of the potential for increased occupant compartment intrusion and performance limitations of current restraint systems. Drawing on data documented in the National Automotive Sampling System (NASS)/ Crashworthiness Data System (CDS) for calendar years 1999 to 2012, the present study examines the characteristics of existing and proposed corner crash test configurations, and the nature of real-world collisions that approximate the test environments. In this analysis, particular emphasis is placed on crash pulse information extracted from vehicle-based event data recorders (EDR's).
Analysis of pedestrian leg contacts and distribution of contact points across the vehicle front
(2015)
Determining the risk to pedestrians that are impacted by areas of the front bumper not currently regulated in type-approval testing requires an understanding of the target population and the injury risk posed by the edges of the bumper. National statistics show that approximately 10% of all accident casualties are pedestrians, with 20% to 30% of these pedestrian casualties being killed or seriously injured. However, the contact position across the front of the bumper is not recorded in national statistics and so in-depth accident databases (OTS, UK and GIDAS, Germany) were used to examine injury risk in greater detail. The results showed that some injury types and severities of injuries appear to peak around the bumper edges. Although there are sometimes inconsistencies in the data, generally there is no evidence to suggest that the edges of the bumper are less likely to be contacted or cause injury.
The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx. However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My. The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was observed. It was also observed that the primary neck response in these tests was flexion, not extension. This correlates well with recent findings from Japan and the United States showing a correlation between neck flexion and injury in accident replication simulations and postmortem human subjects (PMHS) studies, respectively. The present certification tests may not adequately control front cervical spine bumper characteristics, which are important for neck flexion response. The certification sled test also does not include the pelvis and so cannot be used to control pelvis response and does not substantially load the lumbar bumpers and so does not control these parts of the dummy. The stiffness of all spine bumpers and of the pelvis flesh should be much more tightly controlled. It is recommended that a method for certifying the front cervical bumpers should be developed. Recommendations are also made for tighter tolerance on the input parameters for the existing certification tests.
In general the passive safety capability is much greater in newer versus older cars due to the stiff compartment preventing intrusion in severe collisions. However, the stiffer structure which increases the deceleration can lead to a change in injury patterns. In order to analyse possible injury mechanisms for thoracic and lumbar spine injuries, data from the German Inâ€Depth Accident Study (GIDAS) were used in this study. A twoâ€step approach of statistical and caseâ€byâ€case analysis was applied for this investigation. In total 4,289 collisions were selected involving 8,844 vehicles, 5,765 injured persons and 9,468 coded injuries. Thoracic and lumbar spine injuries such as burst, compression or dislocation fractures as well as soft tissue injuries were found to occur in frontal impacts even without intrusion to the passenger compartment. If a MAIS 2+ injury occurred, in 15% of the cases a thoracic and/or lumbar spine injury is included. Considering AIS 2+ thoracic and lumbar spine, most injuries were fractures and occurred in the lumbar spine area. From the case by case analyses it can be concluded that lumbar spine fractures occur in accidents without the engagement of longitudinals, lateral loading to the occupant and/or very severe accidents with MAIS being much higher than the spine AIS.