Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (337) (entfernen)
Schlagworte
- Conference (253)
- Konferenz (252)
- Accident (137)
- Unfall (137)
- Germany (134)
- Deutschland (131)
- Injury (101)
- Verletzung (100)
- Unfallrekonstruktion (73)
- Analyse (math) (61)
Institut
- Sonstige (337) (entfernen)
Because of actual developments and the continuous increase in the field of drive assistant systems, representative and detailed investigations of accident databases are necessary. This lecture describes the possibility to estimate the potential of primary and secondary safety measures by means of a computerized case by case analysis. Single primary or secondary safety measures as well as a combination of both are presented. The method is exemplarily shown for the primary safety measure "Brake Assist" in pedestrian accidents. Regarding accident prevention only the primary safety measure is determined.
Accidents involving two wheels vehicles represent one of the more important types of accidents in Europe. These accidents are usually not easy to reconstruct specially for the analysis of the injuries and its correlation with accident dynamics and evidences. Different methodologies are applied in this work for the reconstruction of two wheeler accidents, especially accident involving motorcycles. From the typologies of road evidences like skid marks, to the use of Pc-Crash and the use of Madymo models, different reconstruction of real accidents are presented. One of the questions that sometimes arise for legal purposes when some type of head injuries arise is if the occupant was wearing or not a helmet. The correlation of head injuries with the use of the helmet is a very important issue, therefore an important legal aspect. One of the key questions for the reconstructions that is difficult to analyze, is if the vehicle occupant, was or not, wearing the helmet. Based on the previously collected information, a generic model of a helmet was developed on CAD 3D, followed by its conversion into finite elements, all in order to perform impact tests using the Madymo software that would help improve the helmet- safety, but that also can be used as a tool in accident reconstruction.
The levels of continuous vehicle automation have become common knowledge. They facilitate overall understanding of the issue. Yet, continuous vehicle automation described therein does not cover "automated driving" as a whole: Functions intervening temporarily in accident-prone situations can obviously not be classified by means of continuous levels. Continuous automation describes the shift in workload from purely human driven vehicles to full automation. Duties of the driver are assigned to the machine as automation levels rise. Emergency braking, e.g., is obviously discontinuous and intensive automation. It cannot be classified under this regime. The resulting absence of visibility of these important functions cannot satisfy " especially in the light of effect they take on traffic safety. Therefore, in order to reach a full picture of vehicle automation, a comprehensive approach is proposed that can map out different characteristics as "Principle of Operation" at top level. On this basis informing and warning functions as well as functions intervening only temporarily in near-accident situations can be described. To reach a complete picture, levels for the discontinuous, temporarily intervening functions are proposed " meant to be the counterpart of the continuous levels already in place. This results in a detailed and independent classification for accident-prone situations. This finally provides for the visibility these important functions deserve.
In recent years the boundaries between active and passive safety blurred more and more. Passive safety in the traditional term includes all safety aspects to prevent occupants to be injured or at least injury severity should be reduced. Passive Safety starts with the collision (first vehicle contact) and ends with rescue (open vehicle doors). Within this phase the occupant has to be protected by the passenger compartment whereby no intrusion should occur. Active safety on the other side was developed to interact prior to the collision whereby the goal is to prevent accidents. The extensive interaction between active and passive safety led to the terminologies "Primary" and "Secondary" safety whereas the expression Integrated Safety Concept was generated. Within this study the most well documented single vehicle accidents with cars not equipped with ESP were identified from the PENDANT database and reconstructed. Additional cases were found in the database ZEDATU of TU Graz. In comparison each case was simulated with the assumption that the cars were equipped with ESP. The differences regarding accident avoidance or crash severity as well as reduction of injury risk were analysed.
In order to enable foreseeing or comparing the benefit of safety systems or driver assistance systems in Germany, in the United States and in Japan, the traffic accident databases in those three countries are examined. The variables used are culpable party, collision partner, accident type, and injury level and the method to re-classify the databases for comparison are proposed. The result indicates that single passenger car fatality is the most frequent in Germany and in the United States, while passenger car vs. pedestrian is the most frequent fatality scenario in Japan. When the casualty by fatality ratio is focused, the greatest difference is observed in rear-end collisions. The ratio of slight injuries in Japan yields about eighteen times as many as those in Germany, and about eight times as many as those in the United States.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
In this study, we compared the injury severity of occupants according to the seating position and the crashing direction in motor vehicle accidents. In the driver's point of view, it was separated the seating position as "Near-side" and "Far-side". The study subjects were targeted by people who visited 4 regional emergency centers following motor vehicle accidents. Real-world investigation was performed by direct and indirect methods after patient- consent. The information of the damaged vehicle was informed by Collision Deformation Classification (CDC) code and the information of the injury of patients was informed by using the Abbreviated Injury Score (AIS) and Injury Severity Score (ISS). When the column 3 in CDC code was P, damaged at the middle part of lateral side, the average point of AIS 3 was 1.91-±1.72 in near-side and 1.02-±1.31 in far-side (p<0.01). The average point of maximum AIS (MAIS) was 2.78-±1.39 in near-side and 2.02-±1.11 in far-side (p<0.01). The average point of ISS was 15.74-±14.71 in near-side and 8.11-±8.39 in far-side (p<0.01). Also, when the column 3 in CDC code was D, damaged at the whole part of lateral side, it was significant that the average point of AIS 3 and MAIS in near-side was bigger than in far-side (p=0.02).
The aim of this study is to investigate the differences in car occupant injury severity recorded in AIS 2005 compared to AIS 1990 and to outline the likely effects on future data analysis findings. Occupant injury data in the UK Cooperative Crash Injury Study Database (CCIS) were coded for the period February 2006 to November 2007 using both AIS 1990 and AIS 2005. Data for 1,994 occupants with over 6000 coded injuries were reviewed at the AIS and MAIS level of severities and body regions to determine changes between the two coding methodologies. Overall there was an apparent general trend for fewer injuries to be coded at the AIS 4+ severity and more injuries to be coded at the AIS 2 severity. When these injury trends were reviewed in more detail it was found that the body regions which contributed the most to these changes in severity were the head, thorax and extremities. This is one of the first studies to examine the implications for large databases when changing to an updated method for coding injuries.
A series of drop tests and vehicle tests with the adult head impactor according to Regulation (EC) 631/2009 and drop tests with the phantom head impactor according to UN Regulation No. 43 have been carried out by the German Federal Highway Research Institute (BASt) on behalf of the German Federal Ministry of Transport, Building and Urban Development (BMVBS). Aim of the test series was to study the injury risk for vulnerable road users, especially pedestrians, in case of being impacted by a motor vehicle in a way described within the European Regulations (EC) 78/2009 and (EC) 631/2009. Furthermore, the applicability of the phantom head drop test described in UN Regulation No. 43 for plastic glazing should be investigated. In total, 30 drop tests, thereof 18 with the adult head impactor and 12 with the phantom head impactor, and 49 vehicle tests with the adult head impactor were carried out on panes of laminated safety glass (VSG), polycarbonate (PC) and laminated polycarbonate (L-PC). The influence of parameters such as the particular material properties, test point locations, fixations, ambient conditions (temperature and impact angle) was investigated in detail. In general, higher values of the Head Injury Criterion (HIC) were observed in tests on polycarbonate glazing. As the HIC is the current criterion for the assessment of head injury risk, polycarbonate glazing has to be seen as more injurious in terms of vulnerable road user protection. In addition, the significantly higher rebound of the head observed in tests with polycarbonate glazing is suspected to lead to higher neck loads and may also cause higher injury risks in secondary impacts of vulnerable road users. However, as in all tests with PC glazing no damage of the panes was observed, the risk of skin cut injuries may be expected to be reduced significantly. The performed test series give no indication for the test procedure prescribed in UN Regulation No. 43 as a methodology to approve glass windscreen not being feasible for polycarbonate glazing, as all PC panes tested fulfilled the UN R 43 requirements. The performance of the windscreen area will not be relevant for vehicle type approval according to the upcoming UN Regulation for pedestrian protection. However, it is recommended that pedestrian protection being considered for plastic windscreens to ensure at least the same level of protection as glass windscreens.
This study aimed at comparing head Wrap Around Distance (WAD) of Vulnerable Road User (VRU) obtained from the German in-depth Accident Database (GIDAS), the China in-depth Accident Database (CIDAS) and the Japanese in-depth Accident Database (ITARDA micro). Cumulative distribution of WAD of pedestrian and cyclist were obtained for each database (AIS2+) showing that WAD of cyclists were larger than the ones of pedestrians. Comparing three regions, the 50%tile WAD of GIDAS was larger than that of both Asian accident databases. Using linear regression that might predict WAD of pedestrians and cyclists from Impact speed and VRU height, WADs were calculated to be 206cm/219cm (Pedestrian/Cyclist) for GIDAS, 170cm/192cm for CIDAS and 211cm/235cm for ITARDA. In addition, this study may be helpful for reconsideration of WAD measurement alignment between accident reconstruction and test procedures.
Cycle helmets have continued to increase in popularity since their introduction half a century ago. Many studies indicate that overall, head injury can be significantly reduced by wearing them. This study was conducted using two distinct sets of real-world cycling collision data from Ireland, namely cases involving police collision reports and cases involving admission to a hospital emergency department. The analyses sought to simulate and analyse the protective performance of cycle helmets in such collision scenarios, by comparing the Head Injury Criterion score and peak head accelerations, both linear and angular. Cycle collisions were simulated using the specialised commercial software MADYMO. From the simulation results, these key metrics were compared between the same-scenario helmeted and unhelmeted cyclist models. Results showed that the inclusion of bicycle helmets reduced linear accelerations very significantly, but also increased angular accelerations significantly compared to unhelmeted situations. Given the modest protective performance of cycle helmets against angular accelerations, it is recommended that cycle helmet manufacturers and international test standards need to pay more attention to head angular accelerations.
One goal of the assessment of the crashworthiness of passenger cars is to characterize the potential of injury outcome to occupants of cars involved in an accident. This can be achieved by the help of an index that puts the number of injured occupants of passenger cars in relation to the number of cars involved in an accident. As a consequence, this index decreases with a lower potential of injury and rises with a higher number of injuries while assuming a fixed number of accidents. Another index is introduced that uses an economical weighting of each injury level. The consequential injury costs are calculated using the average economical costs for lightly, severely and fatally injured persons. The calculation of the safety indices is based on an anonymized sample of accident data provided by the Federal Statistical Office. An index of Mercedes passenger car drivers depending on the year of registration between 1991 and 2006 is compared to the index of drivers of cars of other makes within the same range of registration years.
This paper uses the national accident statistics of Great Britain to evaluate the effectiveness of Electronic Stability Control Systems (ESC) to reduce crash involvement rates. The crash experience of 8,951 cars is analysed and compared to a closely matching set of non-ESC cars using case-control methods. This is one of the largest ESC samples analysed to date. Overall the cars with ESC are involved in 3% fewer crashes although the effectiveness is substantially higher under conditions of adverse road friction. ESC equipped cars are involved in 15% fewer fatal crashes although this reduction represents the combined effect of ESC and passive safety improvements.
Measuring and characterizing airborne particulate matter (PM) is an important research area because PM can lead to impacts on health and to visibility reduction, material damage and groundwater pollution. In regard to road dust, suspension and re-suspension and the contribution of non-exhaust PM to total traffic emissions are expected to increase as a result of predicted climate scenarios. European environmental regulations have been enforced to reduce exhaust particle emissions from road traffic, but little attention has been paid to reducing non-exhaust coarse particle emissions due to traffic. Therefore, a monitoring program for coarse PM has been initiated in early 2013 to assess the predicted increase in the abundance of non-exhaust particles. Particle sampling was performed with the passive-sampler technique Sigma-2. The subsequent single-particle analysis allows for characterization of individual particles, determination of PM size distribution, and calculation of PM mass concentrations. Two motorways n ear Cologne (Koeln), Germany were selected as sampling sites, and the experimental setup in the field was realized with a so-called twin-site method. The present study reports single-particle analysis data for samples collected between May 31, 2013 and May 30, 2014. Coarse PM, generated through multi-source mechanisms, consists of, e.g., tire-wear, soot aggregates, and mineral dust. The highest mass concentration occurs at both motorways in spring, and the observed PM mainly contains traffic-abrasion particles. The field measurements show that the minimum PM concentration was found in the 5 to 12-°C temperature range, whereas the maximum concentration was observed in both the "5 to 5-°C and the 12 to 24-°C ranges, in agreement with previous laboratory measurements. Correlation between super-coarse (d p 10"80 μm, geometric equivalent diameter) PM concentration and precipitation displays a significant increase in concentration with decreasing number of precipitation events (dry weather periods).
The average CO2 concentrations relevant to a motorcyclist wearing an integral helmet were measured twenty years ago and found to be alarmingly high. The present study examined gas concentrations typically inhaled by a motorcyclist. Average concentrations of CO2 for persons (n=4) wearing integral motorcycle helmets were measured in the laboratory and the field to facilitate comparison to previous work, and similarly high average concentrations were found: above 2% when stationary, well below 1% for speeds of 50km/h or more. Detailed measurements of the time-dependent CO2 concentrations during normal inhalation showed levels of about half of the corresponding average concentrations, including 1% at standstill, though higher concentrations (4% or more) are inhaled at the beginning of each breath. Opening the visor at standstill lowered the average inhaled concentration only to about 0.8%. The oxygen deficiency is equal to the CO2 concentration, and could also contribute negatively to motorcyclist cognitive abilities.
Road authorities, freight, and logistic industries face a multitude of challenges in a world changing at an ever growing pace. While globalization, changes in technology, demography, and traffic, for instance, have received much attention over the bygone decades, climate change has not been treated with equal care until recently. However, since it has been recognized that climate change jeopardizes many business areas in transport, freight, and logistics, research programs investigating future threats have been initiated. One of these programs is the Conference of European Directors of Roads (CEDR) Transnational Research Programme (TRP), which emerged about a decade ago from a cooperation between European National Road Authorities and the EU. This paper presents findings of a CEDR project called CliPDaR, which has been designed to answer questions from road authorities concerning climate-driven future threats to transport infrastructure. Pertaining results are based on two potential future socio-economic pathways of mankind (one strongly economically oriented "A2" and one more balanced scenario "A1B"), which are used to drive global climate models (GCMs) producing global and continental scale climate change projections. In order to achieve climate change projections, which are valid on regional scales, GCM projections are downscaled by regional climate models. Results shown here originate from research questions raised by European Road Authorities. They refer to future occurrence frequencies of severely cold winter seasons in Fennoscandia, to particularly hot summer seasons in the Iberian Peninsula and to changes in extreme weather phenomena triggering landslides and rutting in Central Europe. Future occurrence frequencies of extreme winter and summer conditions are investigated by empirical orthogonal function analyses of GCM projections driven with by A2 and A1B pathways. The analysis of future weather phenomena triggering landslides and rutting events requires downscaled climate change projections. Hence, corresponding results are based on an ensemble of RCM projections, which was available for the A1B scenario. All analyzed risks to transport infrastructure are found to increase over the decades ahead with accelerating pace towards the end of this century. Mean Fennoscandian winter temperatures by the end of this century may match conditions of rather warm winter season experienced in the past and particularly warm future winter temperatures have not been observed so far. This applies in an even more pronounced manner to summer seasons in the Iberian Peninsula. Occurrence frequencies of extreme climate phenomena triggering landslides and rutting events in Central Europe are also projected to rise. Results show spatially differentiated patterns and indicate accelerated rates of increases.
Urban runoff is known to transport a significant pollutant load consisting of e.g. heavy metals, salts and hydrocarbons. Interactions between solid and dissolved compounds, proper understanding of particle size distribution, dissolved pollutant fractions and seasonal variations is crucial for the selection and development of appropriate road runoff treatment devices. Road runoff at an arterial road in Augsburg, Germany, has been studied for 3.5 years. A strong seasonal variation was observed, with increased heavy metal concentrations with doubled and tripled median concentrations for heavy metals during the cold season. Correlation analysis showed that de-icing salt is not the only factor responsible for increased pollutant concentrations in winter. During the cold period, the fraction of dissolved metals was lower compared to the warm season. In road dust, the highest metal concentrations were measured for fine particles. Metals in road runoff were found to show a significant correlation to fine particles SS63 (<63 μm). Therefore, it is debatable whether treatment devices only implementing sedimentation processes provide sufficient removal rates.
Powered Two Wheelers (PTWs) accidents constitute one of the road safety problems in Europe. PTWs fatalities represent 22% at EU level in 2006, having increased during last years, representing an opposite trend compared to other road users" figures. In order to reduce these figures it is necessary to investigate the accident causation mechanisms from different points of view (e.g.: human factor, vehicle characteristics, influence of the environment, type of accident). SAFERIDER project ("Advanced telematics for enhancing the SAFEty and comfort of motorcycle RIDERs", under the European Commission "7th Framework Program") has investigated PTW accident mechanisms through literature review and statistical analyses of National and In-depth accident databases; detecting and describing all the possible PTW's accident configurations where the implementation of ADAS (Advanced Driver Assistance Systems) and IVIS (In-Vehicle Information Systems) could contribute to avoid an accident or mitigate its severity. DIANA, the Spanish in-depth database developed by CIDAUT, has been analyzed for that purpose. DIANA comprises of accident investigation teams, in close cooperation with police forces, medical services, forensic surgeons, garages and scrap yards. An important innovation is the fact that before injured people arrive to hospitals, photographs and explanations about the possible accident injury mechanisms are sent to the respective hospitals (via 3G GPRS technology). By this, additional information to medical staff can be provided in order to predict in advance possible internal injuries and select the best medical treatment. This methodology is presented in this paper. On the other hand, the main results (corresponding to road, rider and PTW characteristics; pre and post-accident manoeuvres; road layout; rider behaviour; impact points; accident causations;...) from the analyses of the PTW accidents used for SAFERIDER are shown. Only accident types relevant to ADAS and IVIS devices have been considered.
The national accident statistics demonstrate that the situation of passenger car side impacts is dominated by car to car accidents. Car side to pole impacts are relatively infrequent events. However the importance of car side to pole impacts is significantly increasing with fatal and seriously injured occupants. For the present study the German in-depth database GIDAS (German In-Depth-Accident Study) and the UK based database CCIS (Co-operative Crash Injury Study) were used. Two approaches were undertaken to better understand the scenario of car to pole impacts. The first part is a statistical analysis of passenger car side to pole impacts to describe the characteristics and their importance relevant to other types of impact and to get further knowledge about the main factors influencing the accident outcome. The second part contains a case by case review on passenger cars first registered 1998 onwards to further investigate this type of impact including regression analysis to assess the relationship between injury severity and pole impact relevant factors.